Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ series SMBJ Series Description The SMBJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features t 'BTUSFTQPOTFUJNF typically less than 1.0ps from 0V to BV min t &YDFMMFOUDMBNQJOH capability t -PXJODSFNFOUBMTVSHF resistance t 5ZQJDBM*R less than 1μA above 12V ΔVBR = 0.1% x VBR@25°C x ΔT t )JHI5FNQFSBUVSF soldering guaranteed: t (MBTTQBTTJWBUFEDIJQ 260°C/40 seconds at junction terminals t 8QFBLQVMTFQPXFS t 1MBTUJDQBDLBHFIBT capability at 10×1000μs Underwriters Laboratory waveform, repetition rate Flammability 94V-O (duty cycles):0.01% t .BUUF5JO-FBEoGSFF1MBUFE t)BMPHFO'SFF t 3P)4DPNQMJBOU t 'PSTVSGBDFNPVOUFE applications to optimize board space t -PXQSPmMFQBDLBHF t #VJMUJOTUSBJOSFMJFG t 5ZQJDBMNBYJNVN temperature coefficient Agency Approvals AGENCY AGENCY FILE NUMBER E128662/E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25ºC by 10x1000μs waveform (Fig.1)(Note 1), (Note 2) PPPM 600 W Power Dissipation on infinite heat sink at TA=50OC PM(AV) 5.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 100 A Maximum Instantaneous Forward Voltage at 50A for Unidirectional only (Note 4) VF 3.5V/5.0 V TJ , TSTG -65 to 150 °C Typical Thermal Resistance Junction to Lead RuJL 20 °C/W Typical Thermal Resistance Junction to Ambient RuJA 100 °C/W Operating Junction and Storage Temperature Range Applications TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25OC per Fig. 2. 2. Mounted on copper pad area of 0.2x0.2” (5.0 x 5.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. _ 200V and VF<5.0V for VBR > _ 201V. 4. VF<3.5V for VBR < ©2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to http://www.Littelfuse.com/series/SMBJ.html for current information. 23 Revision: January 09, 2009 SMBJ Series SMBJ Series RoHS Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ series Electrical Characteristics Part Number (Uni) Part Number (Bi) SMBJ5.0A SMBJ6.0A SMBJ6.5A SMBJ7.0A SMBJ7.5A SMBJ8.0A SMBJ8.5A SMBJ9.0A SMBJ10A SMBJ11A SMBJ12A SMBJ13A SMBJ14A SMBJ15A SMBJ16A SMBJ17A SMBJ18A SMBJ20A SMBJ22A SMBJ24A SMBJ26A SMBJ28A SMBJ30A SMBJ33A SMBJ36A SMBJ40A SMBJ43A SMBJ45A SMBJ48A SMBJ51A SMBJ54A SMBJ58A SMBJ60A SMBJ64A SMBJ70A SMBJ75A SMBJ78A SMBJ85A SMBJ90A SMBJ100A SMBJ110A SMBJ120A SMBJ130A SMBJ150A SMBJ160A SMBJ170A SMBJ180A SMBJ200A SMBJ220A SMBJ250A SMBJ300A SMBJ350A SMBJ400A SMBJ440A SMBJ5.0CA SMBJ6.0CA SMBJ6.5CA SMBJ7.0CA SMBJ7.5CA SMBJ8.0CA SMBJ8.5CA SMBJ9.0CA SMBJ10CA SMBJ11CA SMBJ12CA SMBJ13CA SMBJ14CA SMBJ15CA SMBJ16CA SMBJ17CA SMBJ18CA SMBJ20CA SMBJ22CA SMBJ24CA SMBJ26CA SMBJ28CA SMBJ30CA SMBJ33CA SMBJ36CA SMBJ40CA SMBJ43CA SMBJ45CA SMBJ48CA SMBJ51CA SMBJ54CA SMBJ58CA SMBJ60CA SMBJ64CA SMBJ70CA SMBJ75CA SMBJ78CA SMBJ85CA SMBJ90CA SMBJ100CA SMBJ110CA SMBJ120CA SMBJ130CA SMBJ150CA SMBJ160CA SMBJ170CA SMBJ180CA SMBJ200CA SMBJ220CA SMBJ250CA SMBJ300CA SMBJ350CA SMBJ400CA SMBJ440CA Marking UNI BI KE KG KK KM KP KR KT KV KX KZ LE LG LK LM LP LR LT LV LX LZ ME MG MK MM MP MR MT MV MX MZ NE NG NK NM NP NR NT NV NX NZ PE PG PK PM PP PR PT PV PX PZ QE QG QK QM AE AG AK AM AP AR AT AV AX AZ BE BG BK BM BP BR BT BV BX BZ CE CG CK CM CP CR CT CV CX CZ DE DG DK DM DP DR DT DV DX DZ EE EG EK EM EP ER ET EV EX EZ FE FG FK FM Reverse Stand off Voltage VR (Volts) 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 180.0 200.0 220.0 250.0 300.0 350.0 400.0 440.0 Breakdown Voltage VBR (Volts) @ IT MIN MAX 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 201.00 224.00 246.00 279.00 335.00 391.00 447.00 492.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 222.00 247.00 272.00 309.00 371.00 432.00 494.00 543.00 Maximum Maximum Maximum Test Peak Reverse Current Clamping Voltage VC Pulse Leakage IR IT @ Ipp Current Ipp @ VR (mA) (V) (A) (μA) 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 292.0 324.0 356.0 405.0 486.0 567.0 648.0 713.0 65.3 58.3 53.6 50.0 46.6 44.2 41.7 39.0 35.3 33.0 30.2 28.0 25.9 24.6 23.1 21.8 20.6 18.6 16.9 15.5 14.3 13.3 12.4 11.3 10.4 9.3 8.7 8.3 7.8 7.3 6.9 6.5 6.2 5.9 5.3 5.0 4.8 4.4 4.1 3.7 3.4 3.1 2.9 2.5 2.3 2.2 2.1 1.9 1.7 1.5 1.3 1.1 0.9 0.9 800 800 500 200 100 50 20 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X For bidirectional type having VR of 10 volts and less, the IR limit is double. For parts without A , the VBR is ± 10% and Vc is 5% higher than with A parts. SMBJ Series 24 Revision: January 09, 2009 ©2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to http://www.Littelfuse.com/series/SMBJ.html for current information. Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ series Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 2 - Pulse Derating Curve Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % PPPM-Peak Pulse Power (kW) 100 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 100 80 60 40 20 0 0.000001 0.00001 0.0001 0 0.001 td-Pulse Width (sec.) 50 75 100 125 150 175 Figure 4 - Typical Junction Capacitance 10000 150 tr=10μsec TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 Bi-directional V=0V 1000 Cj (pF) IPPM- Peak Pulse Current, % IRSM 25 TA - Ambient Temperature (ºC) Figure 3 - Pulse Waveform Half Value IPPM IPPM ( ) Uni-directional V=0V Uni-directional @VR 100 2 Bi-directional @VR 50 0 10/1000μsec. Waveform as defined by R.E.A 10 Tj=25C f=1.0MHz Vsig=50mVp-p td 1.0 0 2.0 3.0 1 1.0 4.0 t-Time (ms) 10.0 100.0 VBR - Reverse Breakdown Voltage (V) 1000.0 Figure 6 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 5 - Steady State Power Dissipation Derating Curve 6 120 IFSM - Peak Forward Surge Current (A) PM(AV), Steady State Power Dissipation (W) SMBJ Series Figure 1 - Peak Pulse Power Rating 5 4 3 2 1 0 0 25 50 75 100 125 150 Specifications are subject to change without notice. Please refer to http://www.Littelfuse.com/series/SMBJ.html for current information. 80 60 40 20 0 175 1 TA - Ambient Temperature (ºC) ©2009 Littelfuse, Inc. 100 10 100 Number of Cycles at 60 Hz 25 Revision: January 09, 2009 SMBJ Series Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ series Soldering Parameters Reflow Condition -FBEoGSFFBTTFNCMZ tp TP 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) oTFDT Ramp-up TL Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Time (min to max) (ts) oTFDPOET Temperature (T) Pre Heat - Temperature Min (Ts(min)) Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Peak Temperature (TP) 260 Time within 5°C of actual peak Temperature (tp) oTFDPOET Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C +0/-5 Time (t) °C Physical Specifications Environmental Specifications Weight 0.003 ounce, 0.093 grams Temperature Cycle JESD22-A104 Case JEDEC DO214AA. Molded plastic body over glass passivated junction Pressure Cooker JESD 22-A102 Polarity Color band denotes cathode except Bidirectional High Temp. Storage JESD22-A103 Terminal Matte Tin-plated leads, Solderable per JESD22-B102D HTRB JESD22-A108 Thermal Shock JESD22-A106 SMBJ Series Critical Zone TL to TP tL 26 Revision: January 09, 2009 ©2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to http://www.Littelfuse.com/series/SMBJ.html for current information. Transient Voltage Suppression Diodes Surface Mount – 600W > SMBJ series Dimensions Dimensions C B H D F E G K J L Millimeters Min Max A 0.077 B 0.160 Cathode Band A Inches Min Max 0.086 1.950 2.200 0.180 4.060 4.570 C 0.130 0.155 3.300 3.940 D 0.084 0.096 2.130 2.440 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.205 0.220 5.210 5.590 H 0.006 0.012 0.152 0.305 I 0.089 - 2.260 - J 0.085 - 2.160 - K - 0.107 - 2.740 L 0.085 - 2.160 - I Part Numbering System Part Marking System Cathode Band SMBJ XXX C A XXX 5% VOLTAGE TOLERANCE F BI-DIRECTIONAL VOLTAGE SERIES Littelfuse Logo Marking Code Packaging Part number Component Package SMBJxxxXX DO-214AA Quantity 3000 ©2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to http://www.Littelfuse.com/series/SMBJ.html for current information. Packaging Option 5BQF3FFMoNNwUBQF 27 Revision: January 09, 2009 Packaging Specification EIA STD RS-481 SMBJ Series SMBJ Series DO-214AA (SMB J-Bend)