Si5365 P I N - P ROGRAMMABLE P R E C I S I O N C LOCK M U LT IP L I E R Features Not recommended for new designs. For alternatives, see the Si533x family of products. Selectable output frequencies ranging from 19.44 to 1050 MHz Low jitter clock outputs w/jitter generation as low as 0.6 ps rms (50 kHz–80 MHz) Integrated loop filter with selectable loop bandwidth (150 kHz to 1.3 MHz) Four clock inputs w/manual or automatically controlled switching Five clock outputs with selectable signal format (LVPECL, LVDS, CML, CMOS) Support for ITU G.709 FEC ratios (255/238, 255/237, 255/236) LOS alarm outputs Pin-programmable settings On-chip voltage regulator for 1.8 ±5%, 2.5 V ±10%, or 3.3 V ±10% operation Small size: 14 x 14 mm 100-pin TQFP Pb-free, RoHS compliant Ordering Information: See page 21. Applications SONET/SDH OC-48/STM-16 ITU G.709 line cards and STM-64/OC-192 line cards Test and measurement GbE/10GbE, 1/2/4/8/10GFC line cards Description The Si5365 is a low-jitter, precision clock multiplier for high-speed communication systems, including SONET OC-48/OC-192, Ethernet, and Fibre Channel, in which the application requires clock multiplication without jitter attenuation. The Si5365 accepts four clock inputs ranging from 19.44 to 707 MHz and generates five frequency-multiplied clock outputs ranging from 19.44 to 1050 MHz. The input clock frequency and clock multiplication ratio are selectable from a table of popular SONET, Ethernet, and Fibre Channel frequencies. The Si5365 is based on Silicon Laboratories' 3rd-generation DSPLL® technology, which provides anyfrequency synthesis in a highly integrated PLL solution that eliminates the need for external VCXO and loop filter components. The DSPLL loop bandwidth is digitally programmable, providing jitter performance optimization at the application level. Operating from a single 1.8, 2.5, or 3.3 V supply, the Si5365 is ideal for providing clock multiplication in high performance timing applications. Rev. 1.0 9/14 Copyright © 2014 by Silicon Laboratories Si5365 Si5365 Functional Block Diagram CKIN1 ÷ N31 CKIN2 ÷ N32 CKIN3 ÷ N33 CKIN4 ÷ N34 ÷ NC1 CKOUT1 ÷ NC2 CKOUT2 ÷ NC3 CKOUT3 DSPLL® ÷ N2 Divider Select Manual/Auto Switch ÷ NC4 CKOUT4 ÷ NC5 CKOUT5 Clock Select LOS/FOS Alarms Control Frequency Select Bandwidth Select VDD (1.8, 2.5, or 3.3 V) GND 2 Rev. 1.0 Si5365 TABLE O F C ONTENTS Section Page 1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.1. Further Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4. Pin Descriptions: Si5365 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 5. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6. Package Outline: 100-Pin TQFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7. PCB Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 8. Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 8.1. Si5365 Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 8.2. Top Marking Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Rev. 1.0 3 Si5365 1. Electrical Specifications Table 1. DC Characteristics (VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit IDD LVPECL Format 622.08 MHz Out All CKOUTs Enabled — 394 435 mA LVPECL Format 622.08 MHz Out 1 CKOUT Enabled — 253 294 mA CMOS Format 19.44 MHz Out All CKOUTs Enabled — 278 321 mA CMOS Format 19.44 MHz Out 1 CKOUT Enabled — 229 261 mA Disable Mode — 165 — mA 1.8 V ± 5% 0.9 — 1.4 V 2.5 V ± 10% 1 — 1.7 V 3.3 V ± 10% 1.1 — 1.95 V CKNRIN Single-ended 20 40 60 kΩ Single-Ended Input Voltage Swing (See Absolute Specs) VISE fCKIN < 212.5 MHz See Figure 1. 0.2 — — VPP fCKIN > 212.5 MHz See Figure 1. 0.25 — — VPP Differential Input Voltage Swing (See Absolute Specs) VID fCKIN < 212.5 MHz See Figure 1. 0.2 — — VPP fCKIN > 212.5 MHz See Figure 1. 0.25 — — VPP Supply Current1 CKINn Input Pins2 Input Common Mode Voltage (Input Threshold Voltage) Input Resistance VICM Notes: 1. Current draw is independent of supply voltage 2. No under- or overshoot is allowed. 3. LVPECL outputs require nominal VDD ≥ 2.5 V. 4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx Family Reference Manual for more details. 5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz. 4 Rev. 1.0 Si5365 Table 1. DC Characteristics (Continued) (VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit CKOVCM LVPECL 100 load lineto-line VDD – 1.42 — VDD –1.25 V Differential Output Swing CKOVD LVPECL 100 load lineto-line 1.1 — 1.9 VPP Single Ended Output Swing CKOVSE LVPECL 100 load lineto-line 0.5 — 0.93 VPP Differential Output Voltage CKOVD CML 100 load line-toline 350 425 500 mVPP CKOVCM CML 100 load line-toline — VDD-0.36 — V CKOVD LVDS 100 load line-to-line 500 700 900 mVPP Low Swing LVDS 100 load line-to-line 350 425 500 mVPP CKOVCM LVDS 100 load line-toline 1.125 1.2 1.275 V CKORD CML, LVPECL, LVDS — 200 — Output Voltage Low CKOVOLLH CMOS — — 0.4 V Output Voltage High CKOVOHLH VDD = 1.71 V CMOS 0.8 x VDD — — V CKOIO VDD = 1.8 V — 7.5 — mA VDD = 3.3 V — 32 — mA Output Clocks (CKOUTn)3 Common Mode Common Mode Output Voltage Differential Output Voltage Common Mode Output Voltage Differential Output Resistance Output Drive Current (CMOS driving into CKOVOL for output low or CKOVOH for output high. CKOUT+ and CKOUT– shorted externally) Notes: 1. Current draw is independent of supply voltage 2. No under- or overshoot is allowed. 3. LVPECL outputs require nominal VDD ≥ 2.5 V. 4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx Family Reference Manual for more details. 5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz. Rev. 1.0 5 Si5365 Table 1. DC Characteristics (Continued) (VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit VDD = 1.71 V — — 0.5 V VDD = 2.25 V — — 0.7 V VDD = 2.97 V — — 0.8 V VDD = 1.89 V 1.4 — — V VDD = 2.25 V 1.8 — — V VDD = 3.63 V 2.5 — — V 2-Level LVCMOS Input Pins Input Voltage Low Input Voltage High VIL VIH 3-Level Input Pins4 Input Voltage Low VILL — — 0.15 x VDD V Input Voltage Mid VIMM 0.45 x VDD — 0.55 x VDD V Input Voltage High VIHH 0.85 x VDD — — V Input Low Current IILL See Note 4 –20 — — µA Input Mid Current IIMM See Note 4 –2 — +2 µA Input High Current IIHH See Note 4 — — 20 µA Notes: 1. Current draw is independent of supply voltage 2. No under- or overshoot is allowed. 3. LVPECL outputs require nominal VDD ≥ 2.5 V. 4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx Family Reference Manual for more details. 5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz. 6 Rev. 1.0 Si5365 Table 1. DC Characteristics (Continued) (VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit VOL IO = 2 mA VDD = 1.71 V — — 0.4 V IO = 2 mA VDD = 2.97 V — — 0.4 V IO = –2 mA VDD = 1.71 V VDD – 0.4 — — V IO = –2 mA VDD = 2.97 V VDD – 0.4 — — V RSTb = 0 –100 — 100 µA LVCMOS Output Pins Output Voltage Low Output Voltage Low Output Voltage High VOH Output Voltage High Disabled Leakage Current IOZ Notes: 1. Current draw is independent of supply voltage 2. No under- or overshoot is allowed. 3. LVPECL outputs require nominal VDD ≥ 2.5 V. 4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx Family Reference Manual for more details. 5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz. SIGNAL + Differential I/Os VICM , VOCM V VISE , VOSE SIGNAL – (SIGNAL +) – (SIGNAL –) Differential Peak-to-Peak Voltage VID,VOD VICM, VOCM Single-Ended Peak-to-Peak Voltage t SIGNAL + VID = (SIGNAL+) – (SIGNAL–) SIGNAL – Figure 1. Differential Voltage Characteristics 80% CKIN, CKOUT 20% tF tR Figure 2. Rise/Fall Time Characteristics Rev. 1.0 7 Si5365 Table 2. AC Specifications (VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit 19.44 — 707.35 MHz 40 — 60 % 2 — — ns — — 3 pF — — 11 ns CKINn Input Pins Input Frequency CKNF Input Duty Cycle (Minimum Pulse Width) CKNDC Input Capacitance CKNCIN Input Rise/Fall Time CKNTRF Whichever is smaller (i.e., the 40% / 60% limitation applies only to high frequency clocks) 20–80% See Figure 2 CKOUTn Output Pins (See ordering section for speed grade vs frequency limits) Output Frequency (Output not configured for CMOS or Disabled) CKOF 19.44 — 1050 MHz Maximum Output Frequency in CMOS Format CKOF — — 212.5 MHz Output Rise/Fall (20–80 %) @ 622.08 MHz output CKOTRF Output not configured for CMOS or Disabled See Figure 2 — 230 350 ps Output Rise/Fall (20–80%) @ 212.5 MHz output CKOTRF CMOS Output VDD = 1.71 CLOAD = 5 pF — — 8 ns Output Rise/Fall (20–80%) @ 212.5 MHz output CKOTRF CMOS Output VDD = 2.97 CLOAD = 5 pF — — 2 ns Output Duty Cycle Uncertainty @ 622.08 MHz CKODC 100 Load Line-to-Line Measured at 50% Point (Not for CMOS) — — +/-40 ps 8 Rev. 1.0 Si5365 Table 2. AC Specifications (Continued) (VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit LVCMOS Input Pins Minimum Reset Pulse Width Input Capacitance tRSTMN 1 Cin — — 3 pF µs LVCMOS Output Pins Rise/Fall Times tRF CLOAD = 20pf See Figure 2 — 25 — ns LOSTRIG From last CKINn to LOS — — 750 µs Output Clock Skew tSKEW of CKOUTn to of CKOUT_m, C — — 100 ps Phase Change due to Temperature Variation tTEMP Max phase changes from –40 to +85 °C — 300 500 ps — 0.05 0.1 dB Jitter Frequency Loop Bandwidth 5000/BW — — ns pk-pk 1 kHz Offset — –90 — dBc/Hz 10 kHz Offset — –113 — dBc/Hz 100 kHz Offset — –118 — dBc/Hz 1 MHz Offset — –132 — dBc/Hz Max spur @ n x f3 (n 1, n x f3 < 100 MHz) — –93 –70 dBc LOSn Trigger Window Device Skew PLL Performance (fin=fout = 622.08 MHz; BW=120 Hz; LVPECL) Closed Loop Jitter Peaking JPK Jitter Tolerance JTOL Phase Noise fout = 622.08 MHz CKOPN Spurious Noise SPSPUR Rev. 1.0 9 Si5365 Table 3. Jitter Generation Parameter Symbol Jitter Gen OC-192 Test Condition* Typ Max Unit Measurement Filter DSPLL BW2 4–80 MHz 120 Hz — .23 — psrms 0.05–80 MHz 120 Hz — .47 — ps rms 0.12–20 MHz 120 Hz — .48 — ps rms JGEN Jitter Gen OC-48 Min JGEN *Note: Test conditions: 1. fIN = fOUT = 622.08 MHz 2. Clock input: LVPECL 3. Clock output: LVPECL 4. PLL bandwidth: 877 kHz 5. VDD = 3.3 V 6. TA = 85 °C Table 4. Thermal Characteristics (VDD = 1.8 ±5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C) Parameter Thermal Resistance Junction to Ambient 10 Symbol Test Condition Value Unit JA Still Air 40 C°/W Rev. 1.0 Si5365 Table 5. Absolute Maximum Limits Symbol Value Unit DC Supply Voltage VDD –0.5 to 3.8 V LVCMOS Input Voltage VDIG –0.3 to (VDD + 0.3) V CKINn Voltage Level Limits CKNVIN 0 to VDD V XA/XB Voltage Level Limits XAVIN 0 to 1.2 V Operating Junction Temperature TJCT –55 to 150 C Storage Temperature Range TSTG –55 to 150 C 2 kV ESD MM Tolerance; All pins except CKIN+/CKIN– 150 V ESD HBM Tolerance (100 pF, 1.5 kΩ); CKIN+/CKIN– 700 V ESD MM Tolerance; CKIN+/CKIN– 100 V Parameter ESD HBM Tolerance (100 pF, 1.5 kΩ); All pins except CKIN+/CKIN– Latch-Up Tolerance JESD78 Compliant Note: Permanent device damage may occur if the Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as specified in the operation sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods of time may affect device reliability. Phase Noise (dBc/Hz) 622 MHz In, 622 MHz Out BW=877 kHz -50 -70 -90 -110 -130 -150 -170 1000 10000 100000 1000000 10000000 100000000 Offset Frequency (Hz) Figure 3. Typical Phase Noise Plot Jitter Bandwidth RMS Jitter (fs) OC-48, 12 kHz to 20 MHz 374 OC-192, 20 kHz to 80 MHz 388 OC-192, 4 MHz to 80 MHz 181 OC-192, 50 kHz to 80 MHz 377 Broadband, 800 Hz to 80 MHz 420 Rev. 1.0 11 Si5365 2. Typical Application Schematic System Power Supply C10 Ferrite Bead 1 µF C1–9 130 VDD GND 0.1 µF VDD = 3.3 V CKOUT1+ 130 0.1 µF + 100 CKIN1+ CKOUT1– 0.1 µF – CKIN1– 82 Input Clock Sources1 82 Clock Outputs VDD = 3.3 V 130 130 CKIN4+ CKIN4– 82 CKOUT5+ 0.1 µF + 100 82 CKOUT5– 0.1 µF – Si5365 VDD Manual/Automatic Clock15 k Selection (L) AUTOSEL2 15 k Input Clock Select VDD 15 k Frequency Table Select VDD 15 k Frequency Select Bandwidth Select 15 k VDD VDD 15 k CKOUT_3 and CKOUT_4 Divider Control Clock Output 2 Disable/15 k Bypass Mode Control 15 k VDD FRQSEL[3:0]2 BWSEL[1:0]2 15 k 15 k Signal Format Select FRQTBL2 15 k VDD 15 k CKSEL[1:0]3 SFOUT[1:0]2 DIV34[1:0]2 15 k DBL2_BY2 15 k Clock Outputs 3 and 4 Disable CKOUT5 Disable VDD 15 k DBL34 DBL52 15 k Reset ALRMOUT RST CnB Notes: 1. Assumes differential LVPECL termination (3.3 V) on clock inputs. 2. Denotes tri-level input pins with states designated as L (ground), M (VDD/2), and H (VDD). 3. Assumes manual input clock selection. Figure 4. Si5365 Typical Application Circuit 12 Rev. 1.0 Alarm Output Indicator CKIN_n Invalid Indicator (n = 1 to 3) Si5365 3. Functional Description 3.1. Further Documentation The Si5365 is a low jitter, precision clock multiplier for high-speed communication systems, including SONET OC-48/OC-192, SDH STM-16/STM-64, Ethernet, and Fibre Channel, in which the application requires clock multiplication without jitter attenuation. The Si5365 accepts four clock inputs ranging from 19.44 to 707 MHz and generates five frequency-multiplied clock outputs ranging from 19.44 to 1050 MHz. By default the four clock inputs are at the same frequency and the five clock outputs are at the same frequency. Two of the output clocks can be divided down further to generate an integer sub-multiple frequency. The input clock frequency and clock multiplication ratio are selectable from a table of popular SONET, Ethernet, and Fibre Channel frequencies. In addition to providing clock multiplication in SONET and datacom applications, the Si5365 supports SONET-to-datacom frequency translations. Silicon Laboratories offers a PC-based software utility, DSPLLsim, that can be used to look up valid Si5365 frequency translations. This utility can be downloaded from http://www.silabs.com/timing (click on Documentation). Consult the Silicon Laboratories Any-Frequency Precision Clock Family Reference Manual (FRM) for detailed information about the Si5365. Additional design support is available from Silicon Laboratories through your distributor. Silicon Laboratories has developed a PC-based software utility called DSPLLsim to simplify device configuration, including frequency planning and loop bandwidth selection. The FRM and this utility can be downloaded from http://www.silabs.com/timing; click on Documentation. The Si5365 is based on Silicon Laboratories' 3rdgeneration DSPLL® technology, which provides anyfrequency synthesis in a highly integrated PLL solution that eliminates the need for external VCXO and loop filter components. The Si5365 PLL loop bandwidth is digitally programmable via the BWSEL[1:0] pins and supports a range from 150 kHz to 1.3 MHz. The DSPLLsim software utility can be used to calculate valid loop bandwidth settings for a given input clock frequency/clock multiplication ratio. The Si5365 monitors all input clocks for loss-of-signal and provides a LOS alarm when it detects a missing clock. In the case when the input clocks enter alarm conditions, the PLL will freeze the DCO output frequency near its last value to maintain operation with an internal state close to the last valid operating state. The Si5365 has five differential clock outputs. The signal format of the clock outputs is programmable to support LVPECL, LVDS, CML, or CMOS loads. If not required, unused clock outputs can be powered down to minimize power consumption. For system-level debugging, a bypass mode is available which drives the output clock directly from the input clock, bypassing the internal DSPLL. The device is powered by a single 1.8, 2.5, or 3.3 V supply. Rev. 1.0 13 Si5365 VDD VDD CKOUT4+ CKOUT4– VDD SFOUT0 VDD CKOUT2– CKOUT2+ VDD NC VDD CKOUT5+ CKOUT5– VDD DSBL34 VDD CKOUT1+ CKOUT1– VDD SFOUT1 VDD CKOUT3– CKOUT3+ VDD 4. Pin Descriptions: Si5365 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 1 74 2 3 73 4 5 6 7 72 71 8 68 67 70 69 9 10 11 12 13 14 15 16 17 18 19 20 66 65 Si5365 64 63 62 61 60 59 GND PAD 58 57 56 21 55 22 23 54 53 24 52 51 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 GND VDD GND CKIN4+ CKIN4– GND VDD GND CKIN2+ CKIN2– GND DBL2_BY GND CKIN3+ CKIN3– GND VDD GND CKIN1+ CKIN1– GND NC NC NC DBL5 NC NC RST FRQTBL VDD VDD GND GND C1B C2B C3B ALRMOUT CS0_C3A GND VDD GND NC GND GND NC GND AUTOSEL NC NC NC 14 Rev. 1.0 NC NC NC NC FRQSEL3 FRQSEL2 FRQSEL1 FRQSEL0 DIV34_1 DIV34_0 GND GND VDD VDD BWSEL1 BWSEL0 C2A C1A CS1_C4A FOS_CTL GND GND NC NC GND Si5365 Table 6. Si5365 Pin Descriptions Pin # Pin Name I/O Signal Level Description 1, 2, 17, 20, 23, 24, 25, 47, 48, 49, 52, 53, 72, 73, 74, 75, 90 NC 3 RST I LVCMOS 4 FRQTBL I 3-Level Frequency Table Select. This pin selects SONET/SDH, datacom, or SONET/SDH to datacom frequency translation table. L = SONET/SDH. M = Datacom. H = SONET/SDH to Datacom. This pin has a weak pullup and weak pulldown and defaults to M. Some designs may require an external resistor voltage divider when driven by an active device that will tri-state. 5, 6, 15, 27, 32, 42, 62, 63, 76, 79, 81, 84, 86, 89, 91, 94, 96, 99, 100 VDD VDD Supply VDD. The device operates from a 1.8 or 2.5 V supply. Bypass capacitors should be associated with the following VDD pins: Pins Bypass Cap 5, 6 0.1 µF 15 0.1 µF 27 0.1 µF 62, 63 0.1 µF 76, 79 1.0 µF 81, 84 0.1 µF 86, 89 0.1 µF 91, 94 0.1 µF 96, 99, 100 0.1 µF 7, 8, 14, 16, 18, 19, 21, 26, 28, 31, 33, 36, 38, 41, 43, 46, 51, 54, 55, 56, 64, 65 GND GND Supply Ground. These pins must be connected to system ground. Minimize the ground path impedance for optimal performance. No Connect. These pins must be left unconnected for normal operation. External Reset. Active low input that performs external hardware reset of device. Resets all internal logic to a known state and forces the device registers to their default value. Clock outputs are tristated during reset. After rising edge of RST signal, the device will perform an internal self-calibration. This pin has a weak pullup. Rev. 1.0 15 Si5365 Table 6. Si5365 Pin Descriptions (Continued) Pin # Pin Name I/O Signal Level Description 9 C1B O LVCMOS CKIN1 Invalid Indicator. This pin is an active high alarm output associated with CKIN1. Once triggered, the alarm will remain high until CKIN1 is validated. 0 = No alarm on CKIN1. 1 = Alarm on CKIN1. 10 C2B O LVCMOS CKIN2 Invalid Indicator. This pin is an active high alarm output associated with CKIN2. Once triggered, the alarm will remain high until CKIN2 is validated. 0 = No alarm on CKIN2. 1 = Alarm on CKIN2. 11 C3B O LVCMOS CKIN3 Invalid Indicator. This pin is an active high alarm output associated with CKIN3. 0 = No alarm on CKIN3. 1 = Alarm on CKIN3. 12 ALRMOUT O LVCMOS Alarm Output Indicator. This pin is an active high alarm output associated with CKIN4 or the frame sync alignment alarm. 0 = ALRMOUT not active. 1 = ALRMOUT active. 13 57 CS0_C3A CS1_C4A I/O LVCMOS Input Clock Select/CKINn Active Clock Indicator. Input: If manual clock selection mode is chosen (AUTOSEL = 1), the CS[1:0] pins function as the manual input clock selector control. CS[1:0] Active Input Clock 00 CKIN1 01 CKIN2 10 CKIN3 11 CKIN4 These inputs are internally deglitched to prevent inadvertent clock switching during changes in the CSn input state. If configured as input, these pins must not float. Output: If automatic clock detection is chosen (AUTOSEL = M or H), these pins function as the CKINn active clock indicator output. 0 = CKINn is not the active input clock. 1 = CKINn is currently the active input clock to the PLL. This pin has a weak pulldown. 16 22 AUTOSEL I 3-Level Manual/Automatic Clock Selection. Three level input that selects the method of input clock selection to be used. L = Manual. M = Automatic non-revertive. H = Automatic revertive. This pin has a weak pullup and weak pulldown and defaults to M. Some designs may require an external resistor voltage divider when driven by an active device that will tri-state. 29 30 CKIN4+ CKIN4– I MULTI Clock Input 4. Differential clock input. This input can also be driven with a singleended signal. Rev. 1.0 Si5365 Table 6. Si5365 Pin Descriptions (Continued) Pin # Pin Name I/O Signal Level Description 34 35 CKIN2+ CKIN2– I MULTI Clock Input 2. Differential input clock. This input can also be driven with a singleended signal. 37 DBL2_BY I 3-Level CKOUT2 Disable/PLL Bypass Mode Control. Controls enable of CKOUT2 divider/output buffer path and PLL bypass mode. L = CKOUT2 Enabled. M = CKOUT2 Disabled. H = BYPASS Mode with CKOUT2 enabled. Bypass is not available with CMOS outputs. This pin has a weak pullup and weak pulldown and defaults to M. Some designs may require an external resistor voltage divider when driven by an active device that will tri-state. 39 40 CKIN3+ CKIN3– I MULTI Clock Input 3. Differential clock input. This input can also be driven with a singleended signal. 44 45 CKIN1+ CKIN1– I MULTI Clock Input 1. Differential clock input. This input can also be driven with a singleended signal. 50 DBL5 I 3-Level CKOUT5 Disable. This pin performs the following functions: L = Normal operation. Output path is active and signal format is determined by SFOUT inputs. M = CMOS signal format. Overrides SFOUT signal format to allow CKOUT5 to operate in CMOS format while the clock outputs operate in a differential output format. H = Powerdown. Entire CKOUT5 divider and output buffer path is powered down. CKOUT5 output will be in tristate mode during powerdown. This pin has a weak pullup and weak pulldown and defaults to M. Some designs may require an external resistor voltage divider when driven by an active device that will tri-state. 56 FOS_CTL I 3-Level Frequency Offset Control. This pin enables or disables use of the CKIN2 FOS reference as an input to the clock selection state machine. L = FOS Disabled. M = Stratum 3/3E FOS Threshold. H = SONET Minimum Clock FOS Threshold. This pin has both weak pullups and weak pulldowns and defaults to M. Some designs may require an external resistor voltage divider when driven by an active device that will tri-state. 58 C1A O LVCMOS CKIN1 Active Clock Indicator. This pin serves as the CKIN1 active clock indicator. 0 = CKIN1 is not the active input clock. 1 = CKIN1 is currently the active input clock to the PLL. 59 C2A O LVCMOS CKIN2 Active Clock Indicator. This pin serves as the CKIN2 active clock indicator. 0 = CKIN2 is not the active input clock. 1 = CKIN2 is currently the active input clock to the PLL. Rev. 1.0 17 Si5365 Table 6. Si5365 Pin Descriptions (Continued) Pin # Pin Name 60 61 BWSEL0 BWSEL1 I 3-Level Bandwidth Select. These pins are three level inputs that select the DSPLL closed loop bandwidth according to the Any-Frequency Precision Clock Family Reference Manual. These pins have both weak pullups and weak pulldowns and default to M. Some designs may require an external resistor voltage divider when driven by an active device that will tri-state. 66 67 DIV34_0 DIV34_1 I 3-Level CKOUT3 and CKOUT4 Divider Control. These pins control the division of CKOUT3 and CKOUT4 relative to the CKOUT2 output frequency. Detailed operations and timing characteristics for these pins may be found in the Any-Frequency Precision Clock Family Reference Manual. These pins have both weak pullups and weak pulldowns and default to M. Some designs may require an external resistor voltage divider when driven by an active device that will tri-state. 68 69 70 71 FRQSEL0 FRQSEL1 FRQSEL2 FRQSEL3 I 3-Level Multiplier Select. These pins are three level inputs that select the input clock and clock multiplication setting according to the Any-Frequency Precision Clock Family Reference Manual, depending on the FRQTBL setting. These pins have both weak pullups and weak pulldowns and default to M. Some designs may require an external resistor voltage divider when driven by an active device that will tri-state. 77 78 CKOUT3+ CKOUT3– O MULTI Clock Output 3. Differential output clock with a frequency specified by FRQSEL and FRQTBL settings. Output is differential for LVPECL, LVDS, and CML compatible modes. For CMOS format, both output pins drive identical single-ended clock outputs. 18 I/O Signal Level Description Rev. 1.0 Si5365 Table 6. Si5365 Pin Descriptions (Continued) Pin # Pin Name 80 95 SFOUT1 SFOUT0 I/O Signal Level I 3-Level Description Signal Format Select. Three level inputs that select the output signal format (common mode voltage and differential swing) for all of the clock outputs except CKOUT5 (see DBL5). SFOUT[1:0] Signal Format HH Reserved HM LVDS HL CML MH LVPECL MM Reserved ML LVDS—Low Swing LH CMOS LM Disable LL Reserved Bypass mode is not available with CMOS outputs. When VDD = 3.3 V, for thermal reasons, there are restrictions on the number of LVPECL and CMOS outputs. See the Si53xx-RM reference manual for details. These pins have both weak pullups and weak pulldowns and default to M. Some designs may require an external resistor voltage divider when driven by an active device that will tri-state. 82 83 CKOUT1– CKOUT1+ O MULTI 85 DBL34 I LVCMOS 87 88 CKOUT5– CKOUT5+ O MULTI Clock Output 5. Fifth high-speed clock output with a frequency specified by FRQSEL and FRQTBL. Output signal format is selected by SFOUT pins. Output is differential for LVPECL, LVDS, and CML compatible modes. For CMOS format, both output pins drive identical single-ended clock outputs. 92 93 CKOUT2+ CKOUT2– O MULTI Clock Output 2. Differential output clock with a frequency specified by FRQSEL and FRQTBL. Output signal format is selected by SFOUT pins. Output is differential for LVPECL, LVDS, and CML compatible modes. For CMOS format, both output pins drive identical single-ended clock outputs. Clock Output 1. Differential output clock with a frequency specified by FRQSEL and FRQTBL. Output signal format is selected by SFOUT pins. Output is differential for LVPECL, LVDS, and CML compatible modes. For CMOS format, both output pins drive identical single-ended clock outputs. Output 3 and 4 Disable. Active high input. When active, entire CKOUT3 and CKOUT4 divider and output buffer path is powered down. CKOUT3 and CKOUT4 outputs will be in tristate mode during powerdown. This pin has a weak pullup. Rev. 1.0 19 Si5365 Table 6. Si5365 Pin Descriptions (Continued) Pin # Pin Name I/O Signal Level 97 98 CKOUT4– CKOUT4+ O GND PAD 20 GND PAD GND Description MULTI Clock Output 4. Differential output clock with a frequency specified by FRQSEL and FRQTBL settings. Output signal format is selected by SFOUT pins. Output is differential for LVPECL, LVDS, and CML compatible modes. For CMOS format, both output pins drive identical single-ended clock outputs. Supply Ground Pad. The ground pad must provide a low thermal and electrical impedance to a ground plane. Rev. 1.0 Si5365 5. Ordering Guide Ordering Part Number Package ROHS6, Pb-Free Temperature Range Si5365-C-GQ* 100-Pin 14 x 14 mm TQFP Yes –40 to 85 °C *Note: Not recommended for new designs. For alternatives, see the Si533x family. Rev. 1.0 21 Si5365 6. Package Outline: 100-Pin TQFP Figure 5 illustrates the package details for the Si5365. Table 7 lists the values for the dimensions shown in the illustration. Figure 5. 100-Pin Thin Quad Flat Package (TQFP) Table 7. 100-Pin Package Diagram Dimensions Dimension Min Nom Max Dimension Min Nom A — — 1.20 E 16.00 BSC. A1 0.05 — 0.15 E1 14.00 BSC. A2 0.95 1.00 1.05 E2 3.85 4.00 4.15 b 0.17 0.22 0.27 L 0.45 0.60 0.75 c 0.09 — 0.20 aaa — — 0.20 D 16.00 BSC. bbb — — 0.20 D1 14.00 BSC. ccc — — 0.08 ddd — — 0.08 0º 3.5º 7º D2 e 3.85 4.00 4.15 0.50 BSC. Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This package outline conforms to JEDEC MS-026, variant AED-HD. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body Components. 22 Max Rev. 1.0 Si5365 7. PCB Land Pattern Figure 6. PCB Land Pattern Diagram Rev. 1.0 23 Si5365 Table 8. PCB Land Pattern Dimensions Dimension MIN MAX e 0.50 BSC. E 15.40 REF. D 15.40 REF. E2 3.90 4.10 D2 3.90 4.10 GE 13.90 — GD 13.90 — X — 0.30 Y 1.50 REF. ZE — 16.90 ZD — 16.90 R1 R2 0.15 REF — 1.00 Notes: General 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification. 3. This Land Pattern Design is based on IPC-7351 guidelines. 4. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm. Solder Mask Design 5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 µm minimum, all the way around the pad. Stencil Design 6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 7. The stencil thickness should be 0.125 mm (5 mils). 8. The ratio of stencil aperture to land pad size should be 1:1 for the perimeter pads. 9. A 4 x 4 array of 0.80 mm square openings on 1.05 mm pitch should be used for the center ground pad. Card Assembly 10. A No-Clean, Type-3 solder paste is recommended. 11. The recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body Components. 24 Rev. 1.0 Si5365 8. Top Marking 8.1. Si5365 Top Marking 8.2. Top Marking Explanation Mark Method: Laser Logo Size: 9.2 x 3.1 mm Center-Justified Font Size: 3.0 Point (1.07 mm) Right-Justified Line 1 Marking: Device Part Number Si5365x-C-GQ X = Speed Grade See "5. Ordering Guide" on page 21. Line 2 Marking: YY = Year WW = Workweek Assigned by the Assembly Supplier. Corresponds to the year and workweek of the mold date. R = Die Revision Line 3 Marking: TTTTT = Mfg Code Manufacturing Code Circle = 1.8 mm Diameter Center-Justified “e3” Pb-Free Symbol Country of Origin ISO Code Abbreviation Rev. 1.0 25 Si5365 DOCUMENT CHANGE LIST Revision 0.32 to Revision 0.33 Condensed format. Revision 0.33 to Revision 0.34 Removed references to latency control, INC, and DEC pins. Updated Table 1, “Performance Specifications,” on page 2. Changed LVTTL to LVCMOS in Table 2, “Absolute Maximum Ratings,” on page 3. Added Figure 1, “Typical Phase Noise Plot,” on page 4. Updated Figure 4, “Si5365 Typical Application Circuit”. Updated “4. Pin Descriptions: Si5365”. Updated "5. Ordering Guide" on page 21. Added “7. PCB Land Pattern”. Revision 0.34 to Revision 0.4 Changed 1.8 V operating range to ±5%. Updated Table 1 on page 2. Updated Table 2 on page 3. Added page 4. Updated "3. Functional Description" on page 13. Clarified "4. Pin Descriptions: Si5365" on page 14 including the addition of FOS_CTL (pin 56). Revision 0.4 to Revision 0.5 Changed “rate” to “frequency” throughout. Added Table of Contents. Reordered and expanded spec tables. Added 3.3 V operation. Added "8. Top Marking" on page 25. Added no bypass with CMOS outputs. Updated Table 2, “AC Specifications,” on page 8. Updated Table 3, “Jitter Generation,” on page 10. Updated "5. Ordering Guide" on page 21. Revision 0.5 to Revision 1.0 Updated logo. Transitioned to full production. 26 Rev. 1.0 Si5365 NOTES: Rev. 1.0 27 ClockBuilder Pro One-click access to Timing tools, documentation, software, source code libraries & more. Available for Windows and iOS (CBGo only). www.silabs.com/CBPro Timing Portfolio www.silabs.com/timing SW/HW www.silabs.com/CBPro Quality www.silabs.com/quality Support and Community community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com