Si5366 Data Sheet

Si5366
P RECISION C L O C K M ULTIPLIER / J I T T E R A TTENUATOR
Features






Selectable output frequencies

ranging from 8 kHz to 1050 MHz
Ultra-low jitter clock outputs

w/jitter generation as low as
0.3 ps rms (12 kHz–20 MHz)

Integrated loop filter with

selectable loop bandwidth (60 Hz
to 8.4 kHz)

Meets OC-192 GR-253-CORE 
jitter specifications
Four clock inputs w/manual or
automatically controlled hitless 
switching
Five clock outputs with selectable 
signal format (LVPECL, LVDS,
CML, CMOS)
SONET frame sync switching
and regeneration
Support for ITU G.709 FEC ratios
(255/238, 255/237, 255/236)
LOL, LOS, FOS alarm outputs
Pin-controlled output phase
adjust
Pin-programmable settings
On-chip voltage regulator for
1.8 ±5%, 2.5 V ±10%, or
3.3 V ±10% operation
Small size: 14 x 14 mm 100-pin
TQFP
Pb-free, RoHS-compliant
Ordering Information:
See page 25.
Applications
SONET/SDH OC-48/STM-16
 Optical modules
and OC-192/STM-64 line cards  Test and measurement
 GbE/10GbE, 1/2/4/8/10G Fibre  Synchronous Ethernet
Channel line cards
 ITU G.709 line cards

Description
The Si5366 is a jitter-attenuating precision clock multiplier for high-speed
communication systems, including SONET OC-48/OC-192, Ethernet, and
Fibre Channel. The Si5366 accepts four clock inputs ranging from 8 kHz
to 707 MHz and generates five frequency-multiplied clock outputs ranging
from 8 kHz to 1050 MHz. The input clock frequency and clock
multiplication ratio are selectable from a table of popular SONET,
Ethernet, and Fibre Channel frequencies. The Si5366 is based on Silicon
Laboratories' 3rd-generation DSPLL® technology, which provides anyfrequency synthesis and jitter attenuation in a highly integrated PLL
solution that eliminates the need for external VCXO and loop filter
components. The DSPLL loop bandwidth is digitally programmable,
providing jitter performance optimization at the application level.
Operating from a single 1.8, 2.5, or 3.3 V supply, the Si5366 is ideal for
providing clock multiplication and jitter attenuation in high performance
timing applications.
Rev. 1.0 8/12
Copyright © 2012 by Silicon Laboratories
Si5366
Si5366
Functional Block Diagram
Xtal or Refclock
CKIN1
CKIN2
DSPLL
CKIN3
®
÷ NF1
CKOUT1
÷ NF2
CKOUT2
÷ NF3
CKOUT3
N1_HS
CKIN4
Input Clock Configuration
Divider Select
Manual/Auto Switch
Clock Select
÷ NF4
CKOUT4
÷ NF5
CKOUT5 (FS_OUT)
Resonator/Rate Select
LOL/LOS/FOS Alarms
Control
Output Clock2
Frequency Select
Bandwidth Select
Input Clock3
VDD (1.8, 2.5, or 3.3 V)
Skew Control
Input Clock4
GND
FSYNC Align
2
Rev. 1.0
Si5366
TABLE O F C ONTENTS
Section
Page
1. Typical Phase Noise Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2. Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.1. External Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2. Further Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4. Pin Descriptions: Si5366 (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6. Package Outline: 100-Pin TQFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7. PCB Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
8. Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.1. Si5366 Top Marking (TQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.2. Top Marking Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Rev. 1.0
3
Si5366
Table 1. Recommended Operating Conditions1
Parameter
Symbol
Ambient Temperature
TA
Supply Voltage during
Normal Operation
VDD
Test Condition
Min
Typ
Max
Unit
–40
25
85
C
3.3 V Nominal2
2.97
3.3
3.63
V
2.5 V Nominal
2.25
2.5
2.75
V
1.8 V Nominal
1.71
1.8
1.89
V
Notes:
1. All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions.
Typical values apply at nominal supply voltages and an operating temperature of 25 ºC unless otherwise stated.
2. The LVPECL and CMOS output formats draw more current than either LVDS or CML; however, there are restrictions in
the allowed output format pin settings so that the maximum power dissipation for the TQFP devices is limited when
they are operated at 3.3 V. When there are four enabled LVPECL or CMOS outputs, the fifth output must be disabled.
When there are five enabled outputs, there can be no more than three outputs that are either LVPECL or CMOS.
SIGNAL +
Differential I/Os VICM , VOCM
V
VISE , VOSE
SIGNAL –
(SIGNAL +) – (SIGNAL –)
Differential Peak-to-Peak Voltage
VID,VOD
VICM, VOCM
Single-Ended
Peak-to-Peak Voltage
t
SIGNAL +
VID = (SIGNAL+) – (SIGNAL–)
SIGNAL –
Figure 1. Differential Voltage Characteristics
80%
CKIN, CKOUT
20%
tF
tR
Figure 2. Rise/Fall Time Characteristics
4
Rev. 1.0
Si5366
Table 2. DC Characteristics
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
IDD
LVPECL Format
622.08 MHz Out
All CKOUTs Enabled
—
394
435
mA
LVPECL Format
622.08 MHz Out
1 CKOUT Enabled
—
253
284
mA
CMOS Format
19.44 MHz Out
All CKOUTs Enabled
—
278
400
mA
CMOS Format
19.44 MHz Out
1 CKOUT Enabled
—
229
261
mA
Disable Mode
—
165
—
mA
1.8 V ± 5%
0.9
—
1.4
V
2.5 V ± 10%
1
—
1.7
V
3.3 V ± 10%
1.1
—
1.95
V
CKNRIN
Single-ended
20
40
60
k
Single-Ended Input
Voltage Swing
(See Absolute Specs)
VISE
fCKIN < 212.5 MHz
See Figure 1.
0.2
—
—
VPP
fCKIN > 212.5 MHz
See Figure 1.
0.25
—
—
VPP
Differential Input
Voltage Swing
(See Absolute Specs)
VID
fCKIN < 212.5 MHz
See Figure 1.
0.2
—
—
VPP
fCKIN > 212.5 MHz
See Figure 1.
0.25
—
—
VPP
Supply Current1,6
CKINn Input Pins2
Input Common Mode
Voltage (Input Threshold Voltage)
Input Resistance
VICM
Notes:
1. Current draw is independent of supply voltage
2. No under- or overshoot is allowed.
3. LVPECL outputs require nominal VDD ≥ 2.5 V.
4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx Family Reference
Manual for more details.
5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz.
6. The LVPECL and CMOS output formats draw more current than either LVDS or CML; however, there are restrictions in
the allowed output format pin settings so that the maximum power dissipation for the TQFP devices is limited when they
are operated at 3.3 V. When there are four enabled LVPECL or CMOS outputs, the fifth output must be disabled. When
there are five enabled outputs, there can be no more than three outputs that are either LVPECL or CMOS.
Rev. 1.0
5
Si5366
Table 2. DC Characteristics (Continued)
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
CKOVCM
LVPECL 100  load
line-to-line
VDD –1.42
—
VDD –1.25
V
Differential Output
Swing
CKOVD
LVPECL 100  load
line-to-line
1.1
—
1.9
VPP
Single Ended Output
Swing
CKOVSE
LVPECL 100  load
line-to-line
0.5
—
0.93
VPP
Differential Output
Voltage
CKOVD
CML 100  load line-toline
350
425
500
mVPP
CKOVCM
CML 100  load line-toline
—
VDD-0.36
—
V
CKOVD
LVDS
100  load line-to-line
500
700
900
mVPP
Low Swing LVDS
100  load line-to-line
350
425
500
mVPP
CKOVCM
LVDS 100 load lineto-line
1.125
1.2
1.275
V
CKORD
CML, LVPECL, LVDS
—
200
—

Output Voltage Low
CKOVOLLH
CMOS
—
—
0.4
V
Output Voltage High
CKOVOHLH
VDD = 1.71 V
CMOS
0.8 x VDD
—
—
V
CKOIO
VDD = 1.8 V
—
7.5
—
mA
VDD = 3.3 V
—
32
—
mA
Output Clocks (CKOUTn)3,5,6
Common Mode
Common Mode Output
Voltage
Differential Output
Voltage
Common Mode Output
Voltage
Differential Output
Resistance
Output Drive Current
(CMOS driving into
CKOVOL for output low
or CKOVOH for output
high. CKOUT+ and
CKOUT– shorted
externally)
Notes:
1. Current draw is independent of supply voltage
2. No under- or overshoot is allowed.
3. LVPECL outputs require nominal VDD ≥ 2.5 V.
4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx Family Reference
Manual for more details.
5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz.
6. The LVPECL and CMOS output formats draw more current than either LVDS or CML; however, there are restrictions in
the allowed output format pin settings so that the maximum power dissipation for the TQFP devices is limited when they
are operated at 3.3 V. When there are four enabled LVPECL or CMOS outputs, the fifth output must be disabled. When
there are five enabled outputs, there can be no more than three outputs that are either LVPECL or CMOS.
6
Rev. 1.0
Si5366
Table 2. DC Characteristics (Continued)
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
VDD = 1.71 V
—
—
0.5
V
VDD = 2.25 V
—
—
0.7
V
VDD = 2.97 V
—
—
0.8
V
VDD = 1.89 V
1.4
—
—
V
VDD = 2.25 V
1.8
—
—
V
VDD = 3.63 V
2.5
—
—
V
2-Level LVCMOS Input Pins
Input Voltage Low
Input Voltage High
VIL
VIH
Notes:
1. Current draw is independent of supply voltage
2. No under- or overshoot is allowed.
3. LVPECL outputs require nominal VDD ≥ 2.5 V.
4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx Family Reference
Manual for more details.
5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz.
6. The LVPECL and CMOS output formats draw more current than either LVDS or CML; however, there are restrictions in
the allowed output format pin settings so that the maximum power dissipation for the TQFP devices is limited when they
are operated at 3.3 V. When there are four enabled LVPECL or CMOS outputs, the fifth output must be disabled. When
there are five enabled outputs, there can be no more than three outputs that are either LVPECL or CMOS.
Rev. 1.0
7
Si5366
Table 2. DC Characteristics (Continued)
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
3-Level Input Pins4
Input Voltage Low
VILL
—
—
0.15 x VDD
V
Input Voltage Mid
VIMM
0.45 x VDD
—
0.55 x VDD
V
Input Voltage High
VIHH
0.85 x VDD
—
—
V
Input Low Current
IILL
See Note 4
–20
—
—
µA
Input Mid Current
IIMM
See Note 4
–2
—
+2
µA
Input High Current
IIHH
See Note 4
—
—
20
µA
VOL
IO = 2 mA
VDD = 1.71 V
—
—
0.4
V
IO = 2 mA
VDD = 2.97 V
—
—
0.4
V
IO = –2 mA
VDD = 1.71 V
VDD –0.4
—
—
V
IO = –2 mA
VDD = 2.97 V
VDD –0.4
—
—
V
LVCMOS Output Pins
Output Voltage Low
Output Voltage Low
Output Voltage High
Output Voltage High
VOH
Notes:
1. Current draw is independent of supply voltage
2. No under- or overshoot is allowed.
3. LVPECL outputs require nominal VDD ≥ 2.5 V.
4. This is the amount of leakage that the 3-Level inputs can tolerate from an external driver. See Si53xx Family Reference
Manual for more details.
5. LVPECL, CML, LVDS and low-swing LVDS measured with Fo = 622.08 MHz.
6. The LVPECL and CMOS output formats draw more current than either LVDS or CML; however, there are restrictions in
the allowed output format pin settings so that the maximum power dissipation for the TQFP devices is limited when they
are operated at 3.3 V. When there are four enabled LVPECL or CMOS outputs, the fifth output must be disabled. When
there are five enabled outputs, there can be no more than three outputs that are either LVPECL or CMOS.
8
Rev. 1.0
Si5366
Table 3. AC Characteristics
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Single-Ended Reference Clock Input Pin XA (XB with cap to GND)
Input Resistance
XARIN
RATE[1:0] = LM, MH,
ac-coupled
—
12
—
k
Input Voltage Swing
XAVPP
RATE[1:0] = LM, MH,
ac-coupled
0.5
—
1.2
VPP
0.5
—
2.4
VPP
Differential Reference Clock Input Pins (XA/XB)
Input Voltage Swing
XA/XBVPP
RATE[1:0] = LM, MH
CKINn Input Pins
Input Frequency
CKNF
.008
—
707.35
MHz
CKIN3 and CKIN4
used as FSYNC pins
CKNF
—
8
—
kHz
40
—
60
%
2
—
—
ns
—
—
3
pF
—
—
11
ns
Input Duty Cycle
(Minimum Pulse
Width)
CKNDC
Input Capacitance
CKNCIN
Input Rise/Fall Time
CKNTRF
Whichever is smaller
(i.e., the 40% / 60%
limitation applies only
to high frequency
clocks)
20–80%
See Figure 2
CKOUTn Output Pins
(See ordering section for speed grade vs frequency limits)
Output Frequency
(Output not configured for CMOS or
Disabled)
CKOF
0.008
—
1050
MHz
Maximum Output
Frequency in CMOS
Format
CKOF
—
—
212.5
MHz
Output Rise/Fall
(20–80 %) @
622.08 MHz output
CKOTRF
Output not configured for
CMOS or Disabled
See Figure 2
—
230
350
ps
Output Rise/Fall
(20–80%) @
212.5 MHz output
CKOTRF
CMOS Output
VDD = 1.71
CLOAD = 5 pF
—
—
8
ns
*Note: Input to output phase skew after an ICAL is not controlled and can assume any value.
Rev. 1.0
9
Si5366
Table 3. AC Characteristics
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Output Rise/Fall
(20–80%) @
212.5 MHz output
CKOTRF
CMOS Output
VDD = 2.97
CLOAD = 5 pF
—
—
2
ns
Output Duty Cycle
Uncertainty @
622.08 MHz
CKODC
100  Load
Line-to-Line
Measured at 50% Point
(Not for CMOS)
—
—
±40
ps
tRSTMN
1
—
—
µs
Cin
—
—
3
pF
LVCMOS Input Pins
Minimum Reset Pulse
Width
Input Capacitance
LVCMOS Output Pins
Rise/Fall Times
tRF
CLOAD = 20 pF
See Figure 2
—
25
—
ns
LOSn Trigger Window
LOSTRIG
From last CKINn to 
Internal detection of LOSn
—
—
4.5 x N3
TCKIN
Time to Clear LOL
after LOS Cleared
tCLRLOL
LOS to LOL
Fold = Fnew
Stable XA/XB reference
—
10
—
ms
Output Clock Skew
tSKEW
 of CKOUTn to  of
CKOUT_m, CKOUTn
and CKOUT_m at same
frequency
—
—
100
ps
Phase Change due to
Temperature
Variation*
tTEMP
Max phase changes from
–40 to +85 °C
—
300
500
ps
Device Skew
*Note: Input to output phase skew after an ICAL is not controlled and can assume any value.
10
Rev. 1.0
Si5366
Table 3. AC Characteristics
(VDD = 1.8 ± 5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
PLL Performance
(fin = fout = 622.08 MHz; BW = 120 Hz; LVPECL)
Lock Time
tLOCKMP
Start of ICAL to of LOL
—
35
1200
ms
Output Clock Phase
Change
tP_STEP
After clock switch
f3  128 kHz
—
200
—
ps
—
0.05
0.1
dB
Closed Loop Jitter
Peaking
JPK
Jitter Tolerance
JTOL
Jitter Frequency Loop
Bandwidth
5000/BW
—
—
ns pk-pk
CKOPN
1 kHz Offset
—
–106
—
dBc/Hz
10 kHz Offset
—
–121
—
dBc/Hz
100 kHz Offset
—
–132
—
dBc/Hz
1 MHz Offset
—
–131
—
dBc/Hz
Max spur @ n x F3
(n  1, n x F3 < 100 MHz)
—
–93
–70
dBc
Phase Noise
fout = 622.08 MHz
Spurious Noise
SPSPUR
*Note: Input to output phase skew after an ICAL is not controlled and can assume any value.
Rev. 1.0
11
Si5366
Table 4. Jitter Generation
Parameter
Jitter Gen
OC-192
Symbol
JGEN
Test Condition*
Measurement
Filter
DSPLL
BW2
0.02–80 MHz
120 Hz
4–80 MHz
0.05–80 MHz
Jitter Gen
OC-48
JGEN
0.12–20 MHz
Min
Typ
Max
GR-253Specification
Unit
—
4.2
6.2
30
psPP
—
.27
.42
N/A
psrms
—
3.7
6.4
10
psPP
—
.14
.31
N/A
psrms
—
4.4
6.9
10
psPP
—
.26
.41
1.0
ps rms
—
3.5
5.4
40.2
psPP
—
.27
.41
4.02
ps rms
120 Hz
120 Hz
120 Hz
*Note: Test conditions:
1. fIN = fOUT = 622.08 MHz.
2. Clock input: LVPECL .
3. Clock output: LVPECL.
4. PLL bandwidth: 120 Hz.
5. 114.285 MHz 3rd OT crystal used as XA/XB input.
6. VDD = 2.5 V.
7. TA = 85 °C.
8. Jitter integration bands include low-pass (–20 dB/Dec) and high-pass (–60 dB/Dec) roll-offs per Telecordia GR-253CORE.
Table 5. Thermal Characteristics
(VDD = 1.8 ±5%, 2.5 ±10%, or 3.3 V ±10%, TA = –40 to 85 °C)
Parameter
Thermal Resistance Junction to Ambient
12
Symbol
Test Condition
Value
Unit
JA
Still Air
31
C°/W
Rev. 1.0
Si5366
-
Table 6. Absolute Maximum Ratings*
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
—
3.8
V
VDD+0.3
V
DC Supply Voltage
VDD
–0.5
LVCMOS Input Voltage
VDIG
–0.3
CKINn Voltage Level Limits
CKNVIN
0
—
VDD
V
XA/XB Voltage Level Limits
XAVIN
0
—
1.2
V
Operating Junction Temperature
TJCT
–55
—
150
ºC
Storage Temperature Range
TSTG
–55
—
150
ºC
2
—
—
kV
ESD MM Tolerance; All pins
except CKIN+/CKIN–
150
—
—
V
ESD HBM Tolerance
(100 pF, 1.5 k); CKIN+/CKIN–
700
—
—
V
ESD MM Tolerance;
CKIN+/CKIN–
100
—
—
V
ESD HBM Tolerance
(100 pF, 1.5 k); All pins except
CKIN+/CKIN–
Latch-up Tolerance
JESD78 Compliant
*Note: Permanent device damage may occur if the absolute maximum ratings are exceeded. Functional operation should be
restricted to the conditions specified in the operational sections of this data sheet. Exposure to absolute maximum
rating conditions for extended periods of time may affect device reliability.
Rev. 1.0
13
Si5366
1. Typical Phase Noise Performance
Figure 3. Typical Phase Noise Plot
Table 7. RMS Jitter by Band
Jitter Band
RMS Jitter
SONET_OC48, 12 kHz to 20 MHz
249 fs
SONET_OC192_A, 20 kHz to 80 MHz
274 fs
SONET_OC192_B, 4 MHz to 80 MHz
166 fs
SONET_OC192_C, 50 kHz to 80 MHz
267 fs
Brick Wall_800 Hz to 80 MHz
274 fs
*Note: Jitter integration bands include low-pass (–20 dB/Dec) and hi-pass
(–60 dB/Dec) roll-offs per Telcordia GR-253-CORE.
14
Rev. 1.0
Si5366
2. Typical Application Schematic
C10
System
Power
Supply
Ferrite
Bead
Option 2:
Ext.
Refclk–
Ext.
Refclk+
C1–9
VDD = 3.3 V
0.1 µF
0.1 µF
CKIN1+
XA
XB
XA
XB
130 
GND
0.1 µF
VDD
130 
Option 1:
114.285 MHz
Crystal
1 µF
CKIN1–
82 
82 
CKOUT1+
0.1 µF
+
100 
CKOUT1–
Input
Clock
Sources1
0.1 µF
–
VDD = 3.3 V
130 
130 
CKIN4+
CKIN4–
82 
CKOUT4+
CKOUT4–
VDD
CKOUT5/FS_OUT+
15 k
RATE2
CKOUT5/FS_OUT–
CK_CONF
VDD
+
0.1 µF
0.1 µF
–
+
100 
15 k
Input Clock Configuration
Control
Clock
Outputs
100 
82 
Crystal/Ref Clk Rate
0.1 µF
0.1 µF
–
15 k
Manual/Automatic Clock
Selection (L)
15 k
AUTOSEL2
Input Clock Select
VDD
CKSEL[1:0]3
Si5366
15 k
Frequency Offset Control
VDD
15 k
Frequency Table Select
VDD
15 k
Frequency Select
Bandwidth Select
FOS_CTL2
15 k
FRQTBL2
15 k
VDD
15 k
FRQSEL[3:0]2
15 k
BWSEL[1:0]2
15 k
Skew Increment
INC
Skew Decrement
VDD
DEC
15 k
Signal Format Select
VDD
15 k
CKOUT3 and CKOUT4
Divider Control
15 k
Clock Output 2 Disable/
Bypass Mode Control
Clock Outputs 3 and 4
Disable
SFOUT[1:0]2
15 k
VDD
DIV34_[1:0]2
15 k
DBL2_BY2
15 k
VDD
DBL34
15 k
FS_OUT Disable
DBL_FS2
15 k
FSYNC Inputs to Clock
Selection Enable
FS_SW
FSYNC Realignment
Control
FS_ALIGN
Reset
RST
ALRMOUT
Alarm Output Indicator
CKnB
CKINn Invalid Indicator
(n = 1 to 3)
LOL
PLL Loss of Lock
Indicator
Notes: 1. Assumes differential LVPECL termination (3.3 V) on clock inputs.
2. Denotes tri-level input pins with states designated as L (ground), M (VDD/2), and H (VDD).
3. Assumes manual input clock selection.
Figure 4. Si5366 Typical Application Circuit
Rev. 1.0
15
Si5366
3. Functional Description
The Si5366 is a jitter-attenuating precision clock
multiplier for high-speed communication systems,
including SONET OC-48/OC-192, Ethernet, and Fibre
Channel. The Si5366 accepts four clock inputs ranging
from 8 kHz to 707 MHz and generates five frequencymultiplied clock outputs ranging from 8 kHz to
1050 MHz. By default the four clock inputs are at the
same frequency and the five clock outputs are at the
same frequency. Two of the output clocks can be
divided down further to generate an integer sub-multiple
frequency. Optionally, the fifth clock output can be
configured as
a 8 kHz SONET/SDH frame
synchronization output that is phase aligned with one of
the high-speed output clocks. The input clock frequency
and clock multiplication ratio are selectable from a table
of popular SONET, Ethernet, and Fibre Channel
frequencies. In addition to providing clock multiplication
in SONET and datacom applications, the Si5366
supports SONET-to-datacom frequency translations.
Silicon Laboratories offers a PC-based software utility,
DSPLLsim, that can be used to look up valid Si5366
frequency translations. This utility can be downloaded
from
http://www.silabs.com/timing
(click
on
Documentation).
The Si5366 is based on Silicon Laboratories' 3rdgeneration DSPLL® technology, which provides anyfrequency synthesis and jitter attenuation in a highly
integrated PLL solution that eliminates the need for
external VCXO and loop filter components. The Si5366
PLL loop bandwidth is selectable via the BWSEL[1:0]
pins and supports a range from 60 Hz to 8.4 kHz. The
DSPLLsim software utility can be used to calculate valid
loop bandwidth settings for a given input clock
frequency/clock multiplication ratio.
The Si5366 supports hitless switching between input
clocks in compliance with GR-253-CORE and GR-1244CORE that greatly minimizes the propagation of phase
transients to the clock outputs during an input clock
transition (<200 ps typ). Manual and automatic revertive
and non-revertive input clock switching options are
available via the AUTOSEL input pin. The Si5366
monitors the four input clocks for loss-of-signal and
provides a LOS alarm when it detects missing pulses on
any of the four input clocks. The device monitors the
lock status of the PLL. The lock detect algorithm works
by continuously monitoring the phase of the input clock
in relation to the phase of the feedback clock. If a
potential phase cycle slip is detected, the LOL output is
set high. The Si5366 monitors the frequency of CKIN1,
CKIN3, and CKIN4 with respect to a reference
frequency applied to CKIN2, and generates a frequency
offset alarm (FOS) if the threshold is exceeded.
16
This FOS feature is available for SONET applications in
which both the monitored frequency on CKIN1, CKIN3,
and CKIN4 and the reference frequency are integer
multiples of 19.44 MHz. Both Stratum 3/3E and SONET
Minimum Clock (SMC) FOS thresholds are supported.
The Si5366 provides a digital hold capability that allows
the device to continue generation of a stable output
clock when the selected input reference is lost. During
digital hold, the DSPLL is locked to an input frequency
that existed a fixed amount of time before the error
event occurred, eliminating the effects of phase and
frequency transients that may occur immediately
preceding digital hold.
The Si5366 has five differential clock outputs. The
signal format of the clock outputs is selectable to
support LVPECL, LVDS, CML, or CMOS loads. If not
required, unused clock outputs can be powered down to
minimize power consumption. The phase difference
between the selected input clock and the output clocks
is adjustable in 200 ps increments for system skew
control. For system-level debugging, a bypass mode is
available which drives the output clock directly from the
input clock, bypassing the internal DSPLL. The device is
powered by a single 1.8, 2.5, or 3.3 V supply.
3.1. External Reference
An external, high quality clock or a low-cost
114.285 MHz 3rd overtone crystal is used as part of a
fixed-frequency oscillator within the DSPLL. This
external reference is required for the device to perform
jitter attenuation. Silicon Laboratories recommends
using a high-quality crystal. Specific recommendations
may be found in the Family Reference Manual.
In digital hold, the DSPLL remains locked to this
external reference. Any changes in the frequency of this
reference when the DSPLL is in digital hold, will be
tracked by the output of the device. Note that crystals
can have temperature sensitivities.
3.2. Further Documentation
Consult the Silicon Laboratories Any-Frequency
Precision Clock Family Reference Manual (FRM) for
detailed information about the Si5366. Additional design
support is available from Silicon Laboratories through
your distributor.
Silicon Laboratories has developed a PC-based
software utility called DSPLLsim to simplify device
configuration, including frequency planning and loop
bandwidth selection. The FRM and this utility can be
downloaded from http://www.silabs.com/timing; click on
Documentation.
Rev. 1.0
Si5366
VDD
CKOUT3+
CKOUT3–
VDD
SFOUT1
VDD
CKOUT1–
CKOUT1+
VDD
DBL34
FS_OUT–
VDD
FS_OUT+
VDD
NC
VDD
CKOUT2+
CKOUT2–
SFOUT0
VDD
VDD
CKOUT4–
VDD
CKOUT4+
VDD
4. Pin Descriptions: Si5366 (Top View)
NC
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
75
1
NC
NC
2
74
NC
NC
3
73
FRQTBL
4
72
NC
VDD
5
71
FRQSEL3
VDD
6
70
FRQSEL2
GND
7
69
FRQSEL1
GND
8
FRQSEL0
C1B
9
68
67
DIV34_0
RST
DIV34_1
10
66
C3B
11
65
GND
ALRMOUT
12
64
GND
CS0_C3A
13
63
VDD
GND
14
62
VDD
BWSEL1
C2B
Si5366
VDD
15
61
XA
16
17
60
BWSEL0
59
C2A
GND
18
58
C1A
GND
19
57
CS1_C4A
FOS_CTL
XB
GND PAD
FS_SW
20
56
FS_ALIGN
21
55
INC
AUTOSEL
22
54
DEC
NC
23
53
NC
NC
24
25
52
NC
Rev. 1.0
CK_CONF
DBL_FS
LOL
NC
NC
CKIN1–
GND
CKIN1+
GND
GND
RATE1
CKIN3–
CKIN3+
GND
DBL2_BY
GND
CKIN2–
CKIN2+
GND
RATE0
GND
CKIN4–
GND
CKIN4+
VDD
51
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
GND
NC
17
Si5366
Table 8. Si5366 Pin Descriptions
Pin #
Pin Name
1, 2, 23, 24,
25, 47, 48,
52, 53, 72,
73, 74, 75,
90
NC
3
RST
I
LVCMOS
4
FRQTBL
I
3-Level
Frequency Table Select.
This pin selects SONET/SDH, datacom, or SONET/SDH to
datacom frequency translation table.
L = SONET/SDH.
M = Datacom.
H = SONET/SDH to Datacom.
This pin has both weak pull-ups and weak pull-downs and
defaults to M. Some designs may require an external resistor
voltage divider when driven by an active device that will tristate.
5, 6, 15, 27,
62, 63, 76,
79, 81, 84,
86, 89, 91,
94, 96, 99,
100
VDD
VDD
Supply
VDD.
The device operates from a 1.8 or 2.5 V supply. Bypass capacitors should be associated with the following VDD pins:
Pins
Bypass Cap
5, 6
0.1 µF
15
0.1 µF
27
0.1 µF
62, 63
0.1 µF
76, 79
1.0 µF
81, 84
0.1 µF
86, 89
0.1 µF
91, 94
0.1 µF
96, 99, 100
0.1 µF
7, 8, 14, 18,
19, 26, 28,
31, 33, 36,
38, 41, 43,
46, 64, 65
GND
GND
Supply
Ground.
This pin must be connected to system ground. Minimize the
ground path impedance for optimal performance.
9
C1B
O
LVCMOS
18
I/O
Signal Level
Description
No Connect.
These pins must be left unconnected for normal operation.
External Reset.
Active low input that performs external hardware reset of
device. Resets all internal logic to a known state and forces the
device registers to their default value. Clock outputs are disabled during reset. After rising edge of RST signal, the device
will perform an internal self-calibration when a valid input signal
is present.
This pin has a weak pull-up.
CKIN1 Invalid Indicator.
This pin is an active high alarm output associated with CKIN1.
Once triggered, the alarm will remain high until CKIN1 is validated.
0 = No alarm on CKIN1.
1 = Alarm on CKIN1.
Rev. 1.0
Si5366
Table 8. Si5366 Pin Descriptions (Continued)
Pin #
Pin Name
I/O
Signal Level
Description
10
C2B
O
LVCMOS
CKIN2 Invalid Indicator.
This pin is an active high alarm output associated with CKIN2.
Once triggered, the alarm will remain high until CKIN2 is validated.
0 = No alarm on CKIN2.
1 = Alarm on CKIN2.
11
C3B
O
LVCMOS
CKIN3 Invalid Indicator.
This pin is an active high alarm output associated with CKIN3.
0 = No alarm on CKIN3.
1 = Alarm on CKIN3.
12
ALRMOUT
O
LVCMOS
Alarm Output Indicator.
This pin is an active high alarm output associated with CKIN4
or the frame sync alignment alarm.
0 = ALRMOUT not active.
1 = ALRMOUT active.
13
57
CS0_C3A
CS1_C4A
I/O
LVCMO
Input Clock Select/CKINn Active Clock Indicator.
Input: If manual clock selection mode is chosen
(AUTOSEL = L), the CS[1:0] pins function as the manual input clock selector control.
CS[1:0]
Active Input Clock
00
CKIN1
01
CKIN2
10
CKIN3
11
CKIN4
These inputs are internally deglitched to prevent inadvertent clock switching during changes in the CSn input
state. If configured as input, these pins must not float.
Output: If automatic clock detection is chosen (AUTOSEL = M
or H), these pins function as the CKINn active clock
indicator output.
0 = CKINn is not the active input clock.
1 = CKINn is currently the active input clock to the
PLL.
16
17
XA
XB
I
ANALOG
External Crystal or Reference Clock.
An external crystal or an external clock should be connected to
these pins. Frequency of crystal or external clock is set by the
RATE pins. The quality of the selected crystal or external clock
affects the quality of the part's output; refer to the Family Reference Manual for external reference selection and interfacing.
20
FS_SW
I
LVCMOS
FSYNC Inputs to Clock Selection Enable.
If CK_CONF = 1, this pin enables the use of the CKIN3 and
CKIN4 loss-of-signal indicators as inputs to the clock selection
state machine.
0 = Do not use CKIN3 and CKIN4 LOS indicators as inputs to
the clock selection state machine.
1 = Use CKIN3 and CKIN4 LOS indicators as inputs to the
clock selection state machine.
This pin has a weak pull-down.
Rev. 1.0
19
Si5366
Table 8. Si5366 Pin Descriptions (Continued)
20
Pin #
Pin Name
I/O
Signal Level
Description
21
FS_ALIGN
I
LVCMOS
FSYNC Alignment Control.
If CK_CONF = 1, a logic high on this pin causes the FS_OUT
phase to be realigned to the rising edge of the currently active
input sync (CKIN3 or CKIN4).
0 = No realignment.
1 = Realignment.
This pin has a weak pull-down.
22
AUTOSEL
I
3-Level
Manual/Automatic Clock Selection.
Three level input that selects the method of input clock selection to be used.
L = Manual.
M = Automatic non-revertive.
H = Automatic revertive.
This pin has both weak pull-ups and weak pull-downs and
defaults to M. Some designs may require an external resistor
voltage divider when driven by an active device that will tristate.
29
30
CKIN4+
CKIN4–
I
MULTI
Clock Input 4.
Differential clock input. This input can also be driven with a single-ended signal. CKIN4 serves as the frame sync input associated with the CKIN2 clock when CK_CONF = 1.
32
42
RATE0
RATE1
I
3-Level
External Crystal or Reference Clock Rate.
Three-level inputs that select the type and rate of external crystal or reference clock to be applied to the XA/XB port. Refer to
the Family Reference Manual for settings. These pins have
both a weak pull-up and a weak pull-down and default to M.
Some designs may require an external resistor voltage divider
when driven by an active device.
34
35
CKIN2+
CKIN2–
I
MULTI
Clock Input 2.
Differential input clock. This input can also be driven with a single-ended signal.
37
DBL2_BY
I
3-Level
CKOUT2 Disable/PLL Bypass Mode Control.
Controls enable of CKOUT2 divider/output buffer path and PLL
bypass mode.
L = CKOUT2 Enabled.
M = CKOUT2 Disabled.
H = BYPASS Mode with CKOUT2 enabled.
Bypass mode does not support CMOS outputs.
This pin has both weak pull-ups and weak pull-downs and
defaults to M. Some designs may require an external resistor
voltage divider when driven by an active device that will tristate.
39
40
CKIN3+
CKIN3–
I
MULTI
Clock Input 3.
Differential clock input. This input can also be driven with a single-ended signal. CKIN3 serves as the frame sync input associated with the CKIN1 clock when CK_CONF = 1.
44
45
CKIN1+
CKIN1–
I
MULTI
Clock Input 1.
Differential clock input. This input can also be driven with a single-ended signal.
Rev. 1.0
Si5366
Table 8. Si5366 Pin Descriptions (Continued)
Pin #
Pin Name
I/O
Signal Level
Description
49
LOL
O
LVCMOS
PLL Loss of Lock Indicator.
This pin functions as the active high PLL loss of lock indicator.
0 = PLL locked.
1 = PLL unlocked.
50
DBL_FS
I
3-Level
FS_OUT Disable.
This pin performs the following functions:
L = Normal operation. Output path is active and signal format is
determined by SFOUT inputs.
M = CMOS signal format. Overrides SFOUT signal format to
allow FS_OUT to operate in CMOS format while the clock outputs operate in a differential output format.
H = Powerdown. Entire FS_OUT divider and output buffer path
is powered down.
This pin has both weak pull-ups and weak pull-downs and
defaults to M.Some designs may require an external resistor
voltage divider when driven by an active device that will tristate.
51
CK_CONF
I
LVCMOS
Input Clock Configuration Control.
This pin controls the input clock configuration.
0 = CKIN1, 2, 3, 4 inputs, no FS_OUT alignment.
1 = CKIN1, 3 and CKIN2, 4 clock/FSYNC pairs.
This pin has a weak pull-down.
54
DEC
I
LVCMOS
Coarse Skew Decrement.
A pulse on this pin decreases the input to output device skew
by 1/fOSC (approximately 200 ps). Detailed operations and timing characteristics for this pin may be found in the Any-Frequency Precision Clock Family Reference Manual. There is no
limit on the range of skew adjustment by this method. If both
INC and DEC are tied high, phase buildout is disabled and the
device maintains a fixed-phase relationship between the
selected input clock and the output clock during an input clock
switch. Detailed operations and timing characteristics for this
pin may be found in the Any-Frequency Precision Clock Family
Reference Manual.
This pin has a weak pull-down.
55
INC
I
LVCMOS
Coarse Skew Increment.
A pulse on this pin increases the input to output skew by 1/fOSC
(approximately 200 ps). Detailed operations and timing characteristics for this pin may be found in the Any-Frequency Precision Clock Family Reference Manual. There is no limit on the
range of skew adjustment by this method. If both INC and DEC
are tied high, phase buildout is disabled and the device maintains a fixed-phase relationship between the selected input
clock and the output clock during an input clock switch.
Detailed operations and timing characteristics for this pin may
be found in the Any-Frequency Precision Clock Family Reference Manual.
Note: INC does not increase skew if NI_HS = 4.
This pin has a weak pull-down.
Rev. 1.0
21
Si5366
Table 8. Si5366 Pin Descriptions (Continued)
22
Pin #
Pin Name
I/O
Signal Level
Description
56
FOS_CTL
I
3-Level
58
C1A
O
LVCMOS
CKIN1 Active Clock Indicator.
This pin serves as the CKIN1 active clock indicator.
0 = CKIN1 is not the active input clock.
1 = CKIN1 is currently the active input clock to the PLL.
59
C2A
O
LVCMOS
CKIN2 Active Clock Indicator.
This pin serves as the CKIN2 active clock indicator.
0 = CKIN2 is not the active input clock.
1 = CKIN2 is currently the active input clock to the PLL.
60
61
BWSEL0
BWSEL1
I
3-Level
Bandwidth Select.
These pins are three level inputs that select the DSPLL closed
loop bandwidth. Detailed operations and timing characteristics
for these pins may be found in the Any-Frequency Precision
Clock Family Reference Manual.
These pins have both weak pull-ups and weak pull-downs and
default to M. Some designs may require an external resistor
voltage divider when driven by an active device that will tristate.
66
67
DIV34_0
DIV34_1
I
3-Level
CKOUT3 and CKOUT4 Divider Control.
These pins control the division of CKOUT3 and CKOUT4 relative to the CKOUT2 output frequency. Detailed operations and
timing characteristics for these pins may be found in the AnyFrequency Precision Clock Family Reference Manual.
These pins have both weak pull-ups and weak pull-downs and
default to M. Some designs may require an external resistor
voltage divider when driven by an active device that will tristate.
68
69
70
71
FRQSEL0
FRQSEL1
FRQSEL2
FRQSEL3
I
3-Level
Multiplier Select.
These pins are three level inputs that select the input clock and
clock multiplication setting according to the Any-Frequency
Precision Clock Family Reference Manual, depending on the
FRQTBL setting.
These pins have both weak pull-ups and weak pull-downs and
default to M. Some designs may require an external resistor
voltage divider when driven by an active device that will tristate.
77
78
CKOUT3+
CKOUT3–
O
MULTI
Clock Output 3.
Differential output clock with a frequency specified by FRQSEL
and FRQTBL settings. Output is differential for LVPECL, LVDS,
and CML compatible modes. For CMOS format, both output
pins drive identical single-ended clock outputs.
Frequency Offset Control.
This pin enables or disables use of the CKIN2 FOS reference
as an input to the clock selection state machine.
L = FOS Disabled.
M = Stratum 3/3E FOS Threshold.
H = SONET Minimum Clock FOS Threshold.
This pin has both weak pull-ups and weak pull-downs and
defaults to M. Some designs may require an external resistor
voltage divider when driven by an active device that will tristate.
Rev. 1.0
Si5366
Table 8. Si5366 Pin Descriptions (Continued)
Pin #
Pin Name
I/O
Signal Level
Description
80
95
SFOUT1
SFOUT0
I
3-Level
Signal Format Select.
Three level inputs that select the output signal format (common
mode voltage and differential swing) for all of the clock outputs
except FS_OUT. See DBL_FS pin descripition.
SFOUT[1:0]
Signal Format
HH
Reserved
HM
LVDS
HL
CML
MH
LVPECL
MM
Reserved
ML
LVDS—Low Swing
LH
CMOS
LM
Disabled
LL
Reserved
Bypass mode is not supported with CMOS outputs. These pins
have both weak pull-ups and weak pull-downs and default to
M. Some designs may require an external resistor voltage
divider when driven by an active device that will tri-state.
82
83
CKOUT1–
CKOUT1+
O
MULTI
Clock Output 1.
Differential output clock with a frequency specified by FRQSEL
and FRQTBL. Output signal format is selected by SFOUT pins.
Output is differential for LVPECL, LVDS, and CML compatible
modes. For CMOS format, both output pins drive identical single-ended clock outputs.
85
DBL34
I
LVCMOS
Output 3 and 4 Disable.
Active high input. When active, entire CKOUT3 and CKOUT4
divider and output buffer path is powered down. CKOUT3 and
CKOUT4 outputs will be in tristate mode during powerdown.
This pin has a weak pull-up.
87
88
FS_OUT–
FS_OUT+
O
MULTI
Frame Sync Output.
Differential 8 kHz frame sync output or fifth high-speed clock
output with a frequency specified by FRQSEL and FRQTBL.
Output signal format is selected by SFOUT pins. Detailed operations and timing characteristics for this pin may be found in
the Any-Frequency Precision Clock Family Reference Manual.
Output is differential for LVPECL, LVDS, and CML compatible
modes. For CMOS format, both output pins drive identical single-ended clock outputs.
92
93
CKOUT2+
CKOUT2–
O
MULTI
Clock Output 2.
Differential output clock with a frequency specified by FRQSEL
and FRQTBL. Output signal format is selected by SFOUT pins.
Output is differential for LVPECL, LVDS, and CML compatible
modes. For CMOS format, both output pins drive identical single-ended clock outputs.
Rev. 1.0
23
Si5366
Table 8. Si5366 Pin Descriptions (Continued)
Pin #
Pin Name
I/O
Signal Level
Description
97
98
CKOUT4–
CKOUT4+
O
MULTI
Clock Output 4.
Differential output clock with a frequency specified by FRQSEL
and FRQTBL settings. Output signal format is selected by
SFOUT pins. Output is differential for LVPECL, LVDS, and
CML compatible modes. For CMOS format, both output pins
drive identical single-ended clock outputs.
GND PAD
GND PAD
GND
Supply
Ground Pad.
The ground pad must provide a low thermal and electrical
impedance to a ground plane.
24
Rev. 1.0
Si5366
5. Ordering Guide
Ordering Part Number
Package
ROHS6, Pb-Free
Temperature Range
Si5366-C-GQ
100-Pin 14 x 14 mm TQFP
Yes
–40 to 85 °C
Rev. 1.0
25
Si5366
6. Package Outline: 100-Pin TQFP
Figure 5 illustrates the package details for the Si5366. Table 9 lists the values for the dimensions shown in the
illustration.
Figure 5. 100-Pin Thin Quad Flat Package (TQFP)
Table 9. 100-Pin Package Diagram Dimensions
Dimension
Min
Nom
Max
Dimension
Min
Nom
Max
A
—
—
1.20
E
16.00 BSC
A1
0.05
—
0.15
E1
14.00 BSC
A2
0.95
1.00
1.05
E2
3.85
4.00
4.15
b
0.17
0.22
0.27
L
0.45
0.60
0.75
c
0.09
—
0.20
aaa
—
—
0.20
D
16.00 BSC
bbb
—
—
0.20
D1
14.00 BSC
ccc
—
—
0.08
ddd
—
—
0.08

0º
3.5º
7º
D2
e
3.85
4.00
4.15
0.50 BSC
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This package outline conforms to JEDEC MS-026, variant AED-HD.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.
26
Rev. 1.0
Si5366
7. PCB Land Pattern
Figure 6. PCB Land Pattern Diagram
Rev. 1.0
27
Si5366
Table 10. PCB Land Pattern Dimensions
Dimension
MIN
MAX
e
0.50 BSC.
E
15.40 REF.
D
15.40 REF.
E2
3.90
4.10
D2
3.90
4.10
GE
13.90
—
GD
13.90
—
X
—
0.30
Y
1.50 REF.
ZE
—
16.90
ZD
—
16.90
R1
R2
0.15 REF
—
1.00
Notes
General:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification.
3. This Land Pattern Design is based on IPC-7351 guidelines.
4. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition
(LMC) is calculated based on a Fabrication Allowance of 0.05 mm.
Solder Mask Design:
5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder
mask and the metal pad is to be 60 µm minimum, all the way around the pad.
Stencil Design:
6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be
used to assure good solder paste release.
7. The stencil thickness should be 0.125 mm (5 mils).
8. The ratio of stencil aperture to land pad size should be 1:1 for the perimeter pads.
9. A 4 x 4 array of 0.80 mm square openings on 1.05 mm pitch should be used for the center
ground pad.
Card Assembly:
10. A No-Clean, Type-3 solder paste is recommended.
11. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for
Small Body Components.
28
Rev. 1.0
Si5366
8. Top Marking
8.1. Si5366 Top Marking (TQFP)

8.2. Top Marking Explanation
Mark Method:
Laser
Logo Size:
9.2 x 3.1 mm
Center-Justified
Font Size:
3.0 Point (1.07 mm)
Right-Justified
Line 1 Marking:
Device Part Number
Si5366-C-GQ
Line 2 Marking:
YY = Year
WW = Workweek
Assigned by the Assembly Supplier.
Corresponds to the year and workweek of the mold date.
R = Die Revision
Line 3 Marking:
TTTTT = Mfg Code
Manufacturing Code
Circle = 1.8 mm Diameter
Center-Justified
“e3” Pb-Free Symbol
Country of Origin
ISO Code Abbreviation
Rev. 1.0
29
Si5366
DOCUMENT CHANGE LIST
Revision 0.1 to Revision 0.2






Updated Table 1, “Performance Specifications,” on
page 4.
Changed LVTTL to LVCMOS in Table 2, “Absolute
Maximum Ratings,” on page 5.
Added Figure 1, “Typical Phase Noise Plot,” on page
6.
Updated “4. Pin Descriptions: Si5366”.
Updated "5. Ordering Guide" on page 25.
Added “7. PCB Land Pattern”.
Revision 0.2 to Revision 0.3
Changed 1.8 V operating range to ±5%.
 Clarified "4. Pin Descriptions: Si5366" on page 17.
 Updated "6. Package Outline: 100-Pin TQFP" on
page 26.

Revision 0.3 to Revision 1.0





30
Expanded spec tables (1, 2, 3, 4, and 5).
Changed “any-rate” to “any-frequency” throughout.
Added 3.3 V operation.
Added note about bypass with CMOS outputs.
Added device top mark.
Rev. 1.0
Si5366
NOTES:
Rev. 1.0
31
ClockBuilder Pro
One-click access to Timing tools,
documentation, software, source
code libraries & more. Available for
Windows and iOS (CBGo only).
www.silabs.com/CBPro
Timing Portfolio
www.silabs.com/timing
SW/HW
www.silabs.com/CBPro
Quality
www.silabs.com/quality
Support and Community
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using
or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and
"Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to
make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the
included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses
granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent
of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant
personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in
weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®,
EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®,
ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand
names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com