TS12001 Demo Board A 0.65V/1µA Nanopower Voltage Detector with Dual Outputs FEATURES DESCRIPTION The demo board for the TS12001 is a completely assembled and tested circuit board that can be used for evaluating the TS12001. The TS12001 voltage detector combines a 0.58V reference and a comparator with resettable comparator latch in a single package. The TS12001 operates from a single 0.65V to 2.5V power supply and consumes less than 1µA total supply current. Optimized for ultra-long life operation, the TS12001 expands the growing “NanoWatt Analog™” high-performance analog integrated circuits portfolio. 2V Voltage Detector Test Configuration Fully Assembled and Tested 2in x 2in 2-layer circuit board COMPONENT LIST DESIGNATION QTY DESCRIPTION C1, C2 2 R3 R2 R1 VIN, VDD, REF, OVDD, C-OUT1, C-OUT2 HLDB U1 1 1 1 6 0.1µF ±10% capacitor (0805) 10MΩ ± 1% (0805) 4.02MΩ± 1% (0805) 100kΩ± 1% (0805) Test points 1 1 Jumper TS12001ITD1022 The voltage detector exhibits a preset UVLO threshold voltage of 0.78V (typ) or can be set to other threshold voltages with two external resistors. The demo board is configured to detect a threshold voltage of 2V. The TS12001 also offers both push-pull and open-drain outputs. Product data sheet and additional documentation can be found at www.silabs.com. ORDERING INFORMATION Order Number TS12001DB Figure 1. TS12001 Evaluation Board Description TS12001 Demo Board Figure 2. TS12001 Voltage Detector Circuit Page 1 © 2014 Silicon Laboratories, Inc. All rights reserved. TS12001 Demo Board Description The demo board is configured to detect a threshold voltage of 2V with a voltage divider composed of resistors R2 and R3 as shown in Figure 2. In addition, the output driver supply voltage (OVDD) is connected to VDD via a jumper. A test point is available to set OVDD to a different supply voltage if desired. To detect other voltages, resistor values for R2 and R3 can be changed. The design equation is shown below along with Table 1, which provides R2 and R3 resistor combinations for detecting various VIN voltages. R3= VIN x R2‐VSET x R2 VSET VIN Threshold R3(MΩ) R2(MΩ) Voltage(V) 0.9 2.2 4.02 1.07 3.32 4.02 1.28 4.75 4.02 1.52 6.49 4.02 1.85 8.66 4.02 Table 1. Resistor Combinations for Several VIN Threshold Voltages The TS12001 also offers both push-pull and opendrain outputs where the open-drain output has a 100kΩ pull-up resistor. The TS12001 has a latch enable pin (LHDET) that is labeled as HLDB on revision 1 of the demo board. LHDET allows the output of the comparator to latch to a HIGH state under certain conditions. If LHDET is set HIGH, the COUTPP output will switch based on the input to the comparator. When LHDET is set LOW and COUTPP is HIGH, COUTPP will remain HIGH until LHDET goes LOW. When COUTPP is initially LOW instead, COUTPP will latch HIGH until a LOWto-HIGH transition occurs on the COUTPP output. In essence, the LHDET pin offers a LOW-to-HIGH detection. However, LHDET must not be left open. The open-drain output, COUTOD, is the inverter version of the COUTPP output. Connect LHDET to VDD for normal operation or to GND for LHDET enable. The LHDET pin is set HIGH on the board. Page 2 Quick Start Procedures Required Equipment TS12001 demo board DC Power Supply, Single Output Agilent 34401A DMM Signal VDD OVDD GND SET COUTPP COUTOD REFOUT TS12001 VDD OVDD GND VIN C-OUT1 C-OUT2 REF Jumper Setting 1-2 LHDET/HLDB Table 2. Test Points and Jumper Setting In order to evaluate the TS12001 voltage detector, the following steps are to be performed: 1) Before connecting the DC power supply to the demo board power test point, turn on the power supply and set the DC voltage to 2.5V and then turn it off. 2) Connect the positive terminal of a DMM to test point C-OUT1 and the ground terminal to test point GND. Make sure the DMM is set to measure voltage. 3) Connect the positive terminal of the DC power supply to test point VDD and the ground terminal to test point GND. 4) Turn on the power supply and check that the power supply current is approximately 30µA, which is primarily due to the open-drain pull-up resistor R1. At this time, the voltage the DMM is measuring should be approximately 2.5V. 5) Reduce the DC supply voltage slowly and observe the DMM voltage. When the DC supply voltage drops to approximately 2V, the DMM voltage should drop to approximately 0V. This corresponds to a voltage detection of 2V. The power supply current is approximately 1.1µA. The open-drain output voltage (C-OUT2) is the inverted version of C-OUT1. TS12001-EVB Rev. 1.0 TS12001 Demo Board Figure 3. Top Layer Component View Silicon Laboratories, Inc. 400 West Cesar Chavez, Austin, TX 78701 +1 (512) 416-8500 ▪ www.silabs.com Figure 4. Bottom Layer (GND) Page 3 TS12001-EVB Rev. 1.0 Smart. Connected. Energy-Friendly Products Quality Support and Community www.silabs.com/products www.silabs.com/quality community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com