X

DT7450UK2 / MIC-UK
DUAL TEC® Motion Sensor
Designed for tough, commercial environments,
DT7450UK2 and DT7450MIC-UK Motion Sensors
achieve reliable protection with improved false alarm
immunity through DualCore™ signal processing.
Optimum performance is achieved using K-Band
microwave technology and Uniform Sensitivity Optics.
Furthermore the DT7450UK2 offers integrated EOL
resistors which will save on installation time.
DT7450MIC-UK
With its built-in microphone, the DT7450MIC-UK, Alarm
verification will reduce significantly the alarm monitoring
and intervention cost of the security installations.
Using the most proves motion sensors in security where
already over a million is installed, Honeywell offers you a
microphone on board where audible alarm verification
can be perform over a simple pair of security cable.
Features:
Advanced DualCore Signal
with a broad, balloon-shaped pattern
superior false alarm immunity without
Processing
which matches the PIR pattern. It also
compromising detection. DualCore
DualCore signal processing analyzes
offers pattern containment to reduce the
processing not only supports alarm
PIR and microwave signals through the
penetration of microwave energy
functions, but also advanced
DT7450UK2 microcontroller. DualCore
through walls.
temperature compensation, diagnostics,
processing supports a multitude of
Self-Testing for Consistently Reliable
and false alarm features.
advanced functions, including concurrent
Operation
Uniform Sensitivity Optics
diagnostics, digital fluorescent light
Concurrent diagnostics assure optimum
The custom-designed Fresnel lens
interference filter, digital adaptive
performance and reliability. Self-testing
provides the same sensitivity for human
microwave threshold, adaptive
is performed upon power-up and at least
targets at the edge of the pattern as
baselines, and bi-directional temperature
once every hour on the PIR, microwave,
exists directly in front of the sensor,
compensation.
PCB circuitry and temperature
giving the DT7450UK2 consistent
Superb Detection Through K-Band
compensation circuitry.
coverage throughout the protected area.
Technology
DualCore Signal Processing
Built-in microphone (DT7450MIC-UK)
K-Band microwave technology delivers
PIR and microwave signals are analyzed
Adjusting level Microphone with
sharp detection without holes or weak
in the microcontroller in multiple
potentiometer
spots. The custom made source offers
domains, including amplitude, time,
pattern shaping to fill the protected area
frequency and duration to provide
DT7450UK2 / DT7450MIC-UK
DUAL TEC® Motion Sensor
Specifications:
Detection Patterns:
Range
15 x 18 m.
EOL resistors
Alarm: 1K, 2.2K, 4.7K & 5.6K ; default = 1K
(DT7450UK2 only)
Tamper: 1K, 2.2K, 4.7K & 5.6K; default = 1K
Detection zones
22 long range, 12 intermediate, 6 lower,
4 look- down
PIR sensitivity
Low (3-5 steps) and High (1-3 steps)
Frequency
24.200GHz (K-Band)
Mounting height
2.3m optimal
Power requirements
Alarm relay
Tamper
Top View
7.5 – 16V dc, 25 mA typ., 30mA max at 12V dc,
AC Ripple: 3V peak-to-peak at 12V dc nominal
Form A (NC) / 125mA@25 Vdc, max. 20 Ohm,
protective resistor
(NC) 50mA, 24V dc
Side View
Microwave Supervision: Continuous
Self-test intervals
PIR Self-Test: Once every hour
Temp. Compensation: Every 30 seconds
Sensitivity
Low (Pulse count 2): 3-4 steps
High (Pulse count 1): 2-3 steps
Microphone output
15 V peak-to peak; 10 mA max (DT7450-MIC)
Operating temperature
-10oC to +55oC
Temp. compensation
Advanced dual slope
Relative humidity
5% - 95% non condensing
RF Immunity
30 V/m from 10MHz to 1000 MHz
PIR White Light Immunity
6,500 Lux typical
Dimensions
119 x 71 x 42 mm (HxWxD)
Weight
185.5 g.
DT7450MIC-UK board
Ordering:
DT7450UK2
DUAL TEC, 18m, wide angle
DT7450MIC-UK
DUAL TEC, 18m, wide angle with built-in microphone
Accessories:
SMB10
White swivel mount bracket (5 pack)
SMB10C
White ceiling mount bracket (5 pack)
SMB10T
Tampered white swivel mount bracket (5 pack)
Approvals:
EN50131-1, PD6662:2004 with Amendments 1 & 2 and TS50131-2-4, grade 2, Environmental Class III
CE
Honeywell Security & Data Collection
Newhouse Industrial Estate
Motherwell
Lanarkshire
ML1 5SB
Scotland
Tel :+44 (0) 1698 738200
Fax : +44 (0) 1698 738300
www.honeywell.com/security/uk
Honeywell reserves the right to alter
the specification of products without
prior notice.
HSC-DT7450UK-05-EN(1208)DS-Z
December 2008
© 2008 Honeywell International Inc.