TRU 7-16_4 page_031715_Layout 1 3/17/15 10:57 AM Page 1 7-16 Series Panel Mount Receptacles 7-16 Series — Panel Mount Receptacles • Standard designs from stock • Customized modular back-end launch designs • Tri-metal, non-magnetic plating • Slotted finger and solid wall interface designs • PIM (-175 dBc min) TRU Corporation offers a broad range of standard 7-16 series panel mount receptacles for use in both commercial and military applications. These standard designs offer outstanding quality, performance and rapid availability. Our standard 7-16 series designs are available with either a slotted finger or a solid wall interface design to optimize your performance requirements. A slotted finger interface provides mechanically robust resistance against shock and vibration. A solid wall interface offers benefits of lower passive intermodulation (PIM) performance. Our PIM performance is enhanced with standard tri-metal plating that eliminates the magnetic material in the finish. The back-end launch designs of this series are modular and allow for rapid customization of the contact geometry in a cost effective manner. In addition to the standard product included in this brochure, our design team can make a custom configuration for your individual application challenge. Visit our website or contact your local authorized Distribution office for additional support and product information. TRU 7-16_4 page_031715_Layout 1 3/17/15 10:57 AM Page 2 7-16 Series Panel Mount Receptacles Interface Dimensions 7-16 Specifications Electrical Nominal Impedance 50 Ohms Frequency Range DC to 7.5 GHz Voltage Range 2,700 volts rms Dielectric Withstanding Voltage 4,000 volts rms Passive Intermod: slotted finger interface solid wall interface -155 dBc minimum -175 dBc minimum Mechanical Mating Characteristics per IEC 169-4 or DIN 47223 as applicable Connector Durability 500 cycles minimum Recommended Torque 246 in-lbs. (27.8 N-m) nominal Power Rating (7-16 Interface) 7-16 Power Handling 100,000 Temperature Range -85 to +329°F (-65°C to +165°C) Vibration MIL-STD-202 Method 204 Shock MIL-STD-202 Method 213 Moisture Resistance MIL-STD-202 Method 106 Corrosion (salt spray) MIL-STD-202 Method 101 Contacts (inner) Contacts (outer) Brass, tri-metal plating (Cu/Sn/Zn) Female Male 10,000 1,000 100 Materials/Finishes Body CW Power (W) Environmental 1 10 100 Frequency (MHz) Sea level 40°C, Matched Load 1,000 10,000 Beryllium copper, silver plated Brass, silver plated Brass, silver plated Contacts (slotted) Beryllium copper, silver plated Insulators Teflon Gaskets and Seals Silicone rubber Specifications subject to change without notice. For additional specifications or other products, visit us online or call us at 1-800-262-9878. trucorporation.com TRU 7-16_4 page_031715_Layout 1 3/17/15 10:57 AM Page 3 7-16 Series Panel Mount Receptacles 0.974 inch (24,74 mm) Flange mount jack receptacle, threaded contact 0.142 inch (3,61 mm) 4 places M3 THD x 0.125 inch (3,18 mm) 0.85 inch (21,59 mm) Finish TRU-7002-0001-01 Slotted finger Tri-metal TRU-7002-0002-01 Solid wall Tri-metal 0.974 inch (24,74 mm) Flange mount jack receptacle, slotted contact 0.142 inch (3,61 mm) 4 places 0.095 inch (3,41 mm) wide slot 0.142 inch (3,61 mm) 0.119 inch (3,02 mm) Interface Finish TRU-7002-0001-02 Slotted finger Tri-metal TRU-7002-0002-02 Solid wall Tri-metal 0.974 inch (24,74 mm) Flange mount jack receptacle, solder bushing contact 0.142 inch (3,61 mm) 4 places 0.125 inch (3,18 mm) 0.85 inch (21,59 mm) Part Number 1.25 inch (31,75 mm) 0.274 inch (6,96 mm) Part Number Interface Finish TRU-7002-0001-03 Slotted finger Tri-metal TRU-7002-0002-03 Solid wall Tri-metal 1.25 inch (31,75 mm) 0.974 inch (24,74 mm) 0.435 inch (11,05 mm) 0.85 inch (21,59 mm) Interface 1.25 inch (31,75 mm) 0.24 inch (6,10 mm) 0.85 inch (21,59 mm) Part Number 0.125 inch (3,18 mm) Flange mount jack receptacle, solder pot contact 0.142 inch (3,61 mm) 4 places 0.10 inch (2,54 mm) hole 0.69 inch (17,63 mm) Interface Finish TRU-7002-0001-04 Slotted finger Tri-metal TRU-7002-0002-04 Solid wall Tri-metal 1.25 inch (31,75 mm) 0.974 inch (24,74 mm) Flange mount jack receptacle, terminal post contact 0.142 inch (3,61 mm) 4 places 0.204 inch (5,181 mm) 0.85 inch (21,59 mm) Part Number Part Number Interface Finish TRU-7002-0001-05 Slotted finger Tri-metal TRU-7002-0002-05 Solid wall Tri-metal 1.25 inch (31,75 mm) Dimensions shown are reference only. Specifications subject to change without notice. For additional specifications or other products, visit us online or call us at 1-800-262-9878. trucorporation.com TRU 7-16_4 page_031715_Layout 1 3/17/15 10:57 AM Page 4 7-16 Series T 1.787 inch (45,39 mm) 1.850 inch (34,80 mm) 1.140 inch (28,96 mm) 0.125 inch hex (31,75 mm) 0.125 inch hex (31,75 mm) 1.330 inch (33,78 mm) 1.140 inch (28,96 mm) T 7-16 (f) to 7-16 (f) TRU-7657-SSX Silver Finish 7-16 (f) to 7-16 (m) TRU-7750 Silver Finish 7-16 (m) to 7-16 (m) TRU-7701 Silver Finish 0.125 inch hex (31,75 mm) 0.125 inch hex (31,75 mm) 1.370 inch (34,80 mm) 1.370 inch (34,80 mm) Right Angle, 7-16 (f) to 7-16 (m) TRU-7703 Silver Finish 1.433 inch (36,40 mm) 1.370 inch (34,80 mm) 1.433 inch (36,40 mm) 1.370 inch (34,80 mm) Right Angle, 7-16 (m) to 7-16 (m) Right Angle, 7-16 (f) to 7-16 (f) TRU-7704 Silver Finish TRU-7702 Silver Finish Dimensions shown are reference only. TRUlustre™ (Tri-metal) Plating Passive Intermodulation (PIM) TRUlustre™ or equivalent industry tri-metal finishes are used on the 7-16 panel mount receptacle series to provide superior durability, high resistance to tarnishing and a material composition that minimizes passive intermodulation (PIM). Tri-metal plating is a bright, white, copper-tin-zinc alloy with a color similar to stainless steel. TRU 7-16 panel mount receptacles have been designed to minimize PIM distortion when used in critical communication applications. Our products typically achieve (-175 dBc minimum) using a solid wall interface design and (-155 dBc minimum) for a slotted finger interface. Tri-metal composition plating (copper/ tin/zinc) is specified for our standard products to minimize PIM by eliminating ferrous magnetic properties associated with common plating such as nickel. Tri-metal plating has low contact resistance, high abrasion resistance and good ductility, making it an excellent choice for use in RF connectors. Tri-metal plating is non-magnetic (does not contain nickel) and is highly corrosion resistant. Tri-metal plating successfully passes the 96-hour salt spray requirement of MIL-STD-202, method 101C. • Band TRU-7002-0002-01 2 • S/N No. • Time • Carrier • Site • Feeder • Sector p1 -100 Alloy Density Hardness Fully bright white color 53-60% copper, 23-28% tin, 14-20% zinc 7.9-8.1 g/cm 330-380 VHN IM 3 84.20MHz -180.1 -120 IM Level (dBc) Appearance 2012-01-20 13:11:36 -140 -160 -200 0 2 4 6 Time (sec) 8 -137.2 No Detect dBc dBm No Detect dBc dBm Specifications subject to change without notice. For additional specifications or other products, visit us online or call us at 1-800-262-9878. ©2015 TRU Corporation, a division of Winchester Electronics dBm dBc dBm 10 869.0 MHz • Freq2 869.0 MHz • Power1 43 dBm • Power2 43 dBm 0 dB • Offset No Detect -180 • Freq1 • Step 0 MHz • Time 0 msec True • ALC • FilterBW 1.2 KHz REVERSE dBc TRU Corporation Peabody, Massachusetts trucorporation.com