データシート

For more information, please visit the product page.
date 06/2010
page 1 of 5
DESCRIPTION: PIEZO AUDIO TRANSDUCER
PART NUMBER: CPE-2883
SPECIFICATIONS
parameter
conditions/description
operating frequency
min
nom
max
units
2.5
3
3.5
K Hz
28
V dc
8
mA
operating voltage
3
operating current
at 12 V dc
sound pressure level
at 30 cm / 12 V dc
rated voltage
tone
83
dB
12
V dc
continuous
operating temperature
storage temperature
dimenstions
-30
85
°C
-40
95
°C
3.8
g
ø28.6 x H7.5 mm
weight
material
ABS UL-94 1/16” HB high heat (black)
terminal
pin type (au plating)
RoHS
yes
APPEARANCE DRAWING
12.7 0.500
(3 PLCS)
28.6 1.126
3.5 0.138
(3 PLCS)
1.0 0.039
(3 PLCS)
120°
(3 PLCS)
30.0 1.181
7.5 0.295
PCB LAYOUT
TOLERANCE:
±0.3mm UNLESS OTHERWISE
SPECIFIED
20050 SW 112th Ave. Tualatin, Oregon 97062
phone 503.612.2300
fax 503.612.2383 www.cui.com
For more information, please visit the product page.
date 06/2010
page 2 of 5
PART NUMBER: CPE-2883
DESCRIPTION: PIEZO AUDIO TRANSDUCER
VOLTAGE: SPL / CURRENT CONSUMPTION CHARACTERISTICS
20050 SW 112th Ave. Tualatin, Oregon 97062
phone 503.612.2300
fax 503.612.2383 www.cui.com
For more information, please visit the product page.
date 06/2010
page 3 of 5
PART NUMBER: CPE-2883
DESCRIPTION: PIEZO AUDIO TRANSDUCER
MEASUREMENT METHOD
1) S.P.L. measuring circuit
S.P.L. Measuring Circuit
Mic: RION S.P.L. meter UC30 or equivalent
2) The current consumption and the sound pressure level are measured by using the recommended driving circuit
as shown below.
20050 SW 112th Ave. Tualatin, Oregon 97062
phone 503.612.2300
fax 503.612.2383 www.cui.com
For more information, please visit the product page.
date 06/2010
page 4 of 5
DESCRIPTION: PIEZO AUDIO TRANSDUCER
PART NUMBER: CPE-2883
MECHANICAL CHARACTERISTICS
item
test condition
evaluation standard
solderability1
Lead terminals are immersed in rosin for 5 seconds and then immersed in a solder bath of +270 ±5°C for 3 ±1 seconds.
90% min. of the lead terminals will be
wet with solder.
(except the edge of the terminal)
soldering heat resistance
Lead terminals are immersed up to 1.5 mm from the buzzer’s
body in a solder bath of 300 ±5°C for 3 ±0.5 seconds or 260 ±5°C
for 10 ±1 second.
No interference in operation.
terminal mechanical strength
The force of 9.8 N is applied for 10 sec. to each terminal in axial
direction.
No damage or cutting off.
vibration test
The buzzer should be measured after a vibration amplitude of
1.5 mm with 10 ~ 55 Hz band of vibration frequency to each of
the 3 perpendicular directions for 2 hours.
drop test
The buzzer without packaging is subjected to 3 drops on each
axis from the height of 75 cm onto a 40 mm thick wooden board.
The value of oscillation frequency /
current consumption
should be ±10% of the initial
measurements. The SPL should
be within ±10dB compared with
the initial measurement.
Notes:
1. Not recommended for wave soldering
ENVIRONMENT TEST
item
test condition
high temperature test
After being placed in a chamber at +95°C for 240 hours.
evaluation standard
low temperature test
After being placed in a chamber at -40°C for 240 hours.
humidity test
After being placed in a chamber at +40°C and 90 ±5% RH for
240 hours.
temperature cycle test
The part will be subjected to 5 cycles. One cycle will consist of:
The buzzer will be measured after
being placed at +25°C for 4 hours.
The value of the oscillation frequency
/ current consumption should be
±10% compared to the initial
measurements. The SPL should
be within ±10dB compared to the
initial measurements.
RELIABILITY TEST
item
test condition
evaluation standard
operating (life test)
1. Continuous life test:
The part will be subjected to 48 hours of continuous operation at
70°C with rated voltage applied.
The buzzer will be measured after
being placed at +25°C for 4 hours.
The value of the oscillation frequency
/ current consumption should be
±10% compared to the initial
measurements. The SPL should
be within ±10dB compared to the
initial measurements.
2. Intermittent life test:
A duty cycle of 1 minute on, 1 minute off, a minimum of 5,000
times at room temp (+25 ±2°C) with rated voltage applied.
TEST CONDITIONS
standard test conditions
a) Temperature: +5 ~ +35°C
b) Humidity: 45 ~ 85%
c) Pressure: 860 ~ 1060 mbar
judgement test conditions
a) Temperature: +25 ±2°C
b) Humidity: 60 ~ 70%
c) Pressure: 860 ~ 1060 mbar
20050 SW 112th Ave. Tualatin, Oregon 97062
phone 503.612.2300
fax 503.612.2383 www.cui.com
For more information, please visit the product page.
date 06/2010
page 5 of 5
PART NUMBER: CPE-2883
DESCRIPTION: PIEZO AUDIO TRANSDUCER
PACKAGING
20050 SW 112th Ave. Tualatin, Oregon 97062
phone 503.612.2300
fax 503.612.2383 www.cui.com