For more information, please visit the product page. PART NUMBER: CEP-1123 1 of 5 date 08/2009 DESCRIPTION: piezo audio transducer Specifications Resonant frequency Operating voltage Current consumption Sound pressure level Rated voltage Operating temperature Storage temperature Dimensions Weight Material Terminal RoHS page 3.2 ±0.5 KHz 3~28 V dc max. 7 mA max. at 12 V dc 74 db min. at 30 cm / 12 V dc 12 V dc -30 ~ +85° C -40 ~ +95° C ø23.5 x H10.0 mm 3.0 g max. ABS UL-94 1/16” HB High Heat (Black) Pin type (Sn Plating) yes Appearance Drawing Tolerance: ±0.5 red wire ---M blue wire ---F black wire ---G 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 For more information, please visit the product page. PART NUMBER: CEP-1123 page 2 of 5 date 08/2009 DESCRIPTION: piezo audio transducer Measurement Method 1) S.P.L. Measuring Circuit Mic: RION UC 30 or equivalent 2) The current consumption and the S.P.L. are measured by using the recommended driving circuit as shown below. 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 For more information, please visit the product page. PART NUMBER: CEP-1123 Mechanical Characteristics Item Solderability1 Soldering Heat Resistance Terminal Mechanical Strength Vibration Drop Test Notes: page 3 of 5 date 08/2009 DESCRIPTION: piezo audio transducer Evaluation Standard Test Condition 90% min. of the lead terminals Lead terminals are immersed in rosin for will be wet with solder. (Except 5 seconds and then immersed in solder bath the edge of the terminal) of 270 ±5°C for 3 ±1 seconds. Lead terminals are immersed up to 1.5mm from No interference in operation. buzzer’s body in solder bath of 300 ±5°C for 3 ±0.5 or 260 ±5°C for 10 ±1 seconds. No damage or cutting off. For 10 seconds, the force of 9.8N (1.0kg) is applied to each terminal in axial direction. The buzzer should be measured after applying The value of oscillation frequency/current consumption a vibration amplitude of 1.5 mm with 10 to should be ±10% of the initial 55 Hz band of vibration frequency to each of measurements. The SPL should the 3 perpendicular directions for 2 hours. be within ±10dB compared with The part will be dropped from a height of the initial measurement. 75 cm onto a 40 mm thick wooden board 3 times in 3 axes (X, Y, Z) for a total of 9 drops. 1. Not recommended for wave soldering Environment Test Item High temp. test Low temp. test Humidity test Temp. cycle test Test Condition After being placed in a chamber at +95°C for 240 hours. After being placed in a chamber at -40°C for 240 hours. After being placed in a chamber at +40°C and 90±5% relative humidity for 240 hours. The part shall be subjected to 5 cycles. One cycle will consist of: Evaluation Standard The buzzer will be measured after being placed at +25°C for 4 hours. The value of the oscillation frequency/current consumption should be ±10% compared to the initial measurements. The SPL should be within ±10dB compared to the initial measurements. 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 For more information, please visit the product page. page 4 of 5 date 08/2009 DESCRIPTION: piezo audio transducer PART NUMBER: CEP-1123 Reliability Test Item Operating (Life Test) Test Condition 1. Continuous life test: The part will be subjected to 48 hours of continuous operation at +70°C with rated voltage applied. 2. Intermittent life test: A duty cycle of 1 minute on, 1 minute off, a minimum of 5,000 times at room temp (+25 ±2°C) with rated voltage applied. Evaluation Standard The buzzer will be measured after being placed at +25°C for 4 hours. The value of the oscillation frequency/current consumption should be ±10% compared to the initial measurements. The SPL should be within ±10dB compared to the initial measurements. Test Conditions Standard Test Condition Judgement Test Condition a) Tempurature: +5 ~ +35°C a) Tempurature: +25 ±2°C b) Humidity: 45 - 85% b) Humidity: 60 - 70% c) Pressure: 860-1060 mbar c) Pressure: 860-1060 mbar 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383 For more information, please visit the product page. PART NUMBER: CEP-1123 page 5 of 5 date 08/2009 DESCRIPTION: piezo audio transducer Packaging 20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383