Download Specification Sheet

SPECIFICATION
FOR
APPROVAL
Customer:
Description: ELECTRO MAGNETIC BUZZER
SOBERTON Part No. :GT-111PS-1
Date:2015-04-27
Customer Model No. :
Date of Approval
Authorization
Signature
211 N.First Street Minneapolis, MN. 55401
Tel:612-849-6205 Fax:952-933-3120
Http://www.soberton.comE-mail:[email protected]
Approved
Checked
Design
Jasmine
Frank
Jim
2015/4/27
2015/4/27
2015/4/27
A. SCOPE
This specification applies magnetic buzzer,
GT-111PS-1
B. SPECIFICATION
No.
Item
Unit
Specification
Condition
1
Oscillation Frequency
Hz
2048
Vo-p=1/2duty , square wave
2
Operating Voltage
Vo-p
1~ 3
3
Rated Voltage
Vo-p
1.5
4
Current Consumption
mA
MAX.15
at Rated Voltage
5
Sound Pressure Level
dB
MIN. 70
at 10cm at Rated Voltage
6
Coil Resistance
Ω
50±7.5
7
Operating Temperature
-20 ~ +70
8
Storage Temperature
-30 ~ +80
9
Dimension
mm
Φ12.0 x H5.4
10
Weight (MAX)
gram
1.6
11
Housing Material
PPO
12
Leading Pin
Tin Plated Brass(Sn)
13
Environmental
Protection Regulation
RoHS
See appearance drawing
See appearance drawing
C. APPEARANCE DRAWING
-
+
SOUND EMISSION HOLE
Tol : ± 0.5
Unit: mm
D.TESTING METHOD
Standard Measurement conditions
Temperature:25±2℃ Humidity:45-65%
Acoustic Characteristics:
The oscillation frequency, current consumption and sound pressure are measured by the
measuring instruments shown below
In the measuring test, buzzer is placed as follows:
E. Typical Frequency Response Curve
F. RELIABILITY TEST
NO.
ITEM
1
High Temperature
Test (Storage)
2
Low Temperature
Test (Storage)
3
Humidity Test
TEST CONDITION AND REQUIREMENT
After being placed in a chamber with 80±2ºC for 96 hours and then
being placed in normal condition for 2 hours.
Allowable variation of SPL after test: ±10dB.
After being Placed in a chamber with -30±2ºC for 96 hours and then
being placed in normal condition for 2 hours.
Allowable variation of SPL after test: ±10dB.
After being Placed in a chamber with 90-95% R.H. at 40±2ºC for 96
hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: ±10dB.
The part shall be subjected to 5 cycles. One cycle shall be consist of:
+70ºC
+25ºC
4
Temperature Cycle
Test
5
Drop Test
6
Vibration Test
7
Solderability
Test
8
Terminal Strength
Pulling Test
+25ºC
- 20ºC
Allowable variation of SPL after test: ±10dB.
Drop on a hard wood board of 4cm thick, any directions ,6 times,
at the height of 75cm .
Allowable variation of SPL after test: ±10dB.
After being applied vibration of amplitude of 1.5mmwith 10 to 55 Hz
band of vibration frequency to each of 3 perpendicular directions for
2 hours .
Allowable variation of SPL after test: ±10dB.
Lead terminals are immersed in rosin for 5 seconds and then
immersed in solder bath of +300±5ºC for 3±1 seconds .
90% min. lead terminals shall be wet with solder
(Except the edge of terminals).
The force of 9.8N(1.0kg) is applied to each terminal in axial direction for
10 seconds.
No visible damage and cutting off.
TEST CONDITION.
Standard Test Condition
:
a) Temperature : +5 ~ +35℃ b) Humidity : 45-85%
c) Pressure : 860-1060mbar
Judgment Test Condition
:
a) Temperature : +25 ± 2℃
c) Pressure : 860-1060mbar
b) Humidity : 60-70%
G. PACKING STANDARD
10x10=100PCS
Foam Tray
顶层加一块上盖
Carton Box
(5PCS Plastic Bag)
Foam Tray
240mmx160mmx30mm
10x100PCS=1000PCS
Plastic Bag
Carton Box
1x100PCS=100PCS
520mmx420mmx280mm
5x1000PCS=5,000PCS