Datasheet

Series 602
10A, 250Vac Optically Isolated
AC Solid-State Relay
Part*
DESC Drawing Relay Description
Number
Number
602-1W
602-1Y
10 A, 250 VAC AC Solid State Relay
86031-001
10 A, 250 VAC AC Solid State Relay
* The Y suffix denotes parameters tested to MIL-PRF-28750 test methods.
The W suffix denotes parameters tested to Teledyne specifications.
ELECTRICAL SPECIFICATIONS
FEATURES
• Available to DESC drawing
86031-001
(-55°C TO +95°C UNLESS OTHERWISE SPECIFIED)
• Optical isolation
INPUT (CONTROL) CHARACTERISTICS
Min
Typ
• Low minimum output current
Max Units
• Zero voltage turn-on
Input Current (See Figure 1)
VIN = 5 Vdc
VIN=32 Vdc
15 mA dc
16 mA dc
Turn-Off Voltage (Guaranteed Off)
Turn-On Voltage (Guaranteed On)
1.0
3.8
Vdc
Vdc
Reverse Voltage Protection
Input Voltage Range
3.8
-32
Vdc
32
Vdc
OUTPUT (LOAD) SPECIFICATIONS
Min
Typ
Max Units
Output Current Range (See Figure 3)
0.1
10
Amps
Output voltage Rating
25
250
Vac
Frequency Range
45
440
Hz
Output Voltage Drop @ 10 Amp (See Figure 2)
1.5
Vrms
Off-State Leakage Current
(250 Vac, 400 Hz)
8.0
mA
Turn-On Time
1/2
Cycle
Turn-Off Time
1
Cycle
Transient Voltage (20 msec)
+460
V pk
Overload Current (16.6 msec)
100 Amps
Zero Voltage Turn-On Point
+15
dv/dt @ 25oC (See Note 4)
200
Load Power Factor
0.2
Insulation Resistance @ 500 Vdc
109
Input to Output Capacitance
602 82
• Extremely low EMI
• Zero current turn-off
• Logic compatible input
• Available to Y screening levels
of MIL-PRF-28750
DESCRIPTION
The 602-1 is an AC output solidstate relay designed for power
switching. The relay incorporates a
hermetically sealed, optically
coupled solid state relay as a
driver. This driver provides zero
voltage turn-on as well as a logic
compatible control circuit. The
relay output is rated for 10A at
250Vac and switches the load with
a hermetically sealed triac. A builtin snubber circuit provides reliable
switching of both resistive and
reactive loads with power factors
as low as 0.2. The internal
components are potted with a
thermally conductive epoxy, which
provides an environmental seal for
severe environmental conditions
encountered in military and
aerospace applications. The 602-1
is available in W and Y screening
levels. The 602-1Y is available to
DESC drawing 86031-001.
Vpk
V/µs
WIRING DIAGRAM
Ohm
15
pF
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2002 TELEDYNE RELAYS
602\072002\Q1
Series 602
OUTPUT (LOAD) SPECIFICATIONS
Min
Dielectric Withstanding Voltage
Typ
Max
1500
Units
Vac
o
Junction Temperature (TJ Max)
150
C
Thermal Resistance Junction to Ambient (θJA)
15.5
o
Thermal Resistance Junction to Case (θJC)
2.5
o
C/W
C/W
ENVIRONMENTAL SPECIFICATIONS
Min
Ambient Temperature
Operating
Storage
Typ
-55
-55
Max
+95
+110
Units
o
o
INPUT CURRENT VS
INPUT VOLTAGE
FIGURE 1
C
C
Shock for 6 ms
100
g
Vibration, 78 to 2000 Hz
30
g
100
g
(0.1 Double Amplitude 10 to 78 Hz)
Acceleration
MECHANICAL SPECIFICATIONS
LOAD CURRENT VS TYPICAL
OUTPUT VOLTAGE DROP
FIGURE 2
THERMAL DERATING CURVES
FIGURE 3
DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS)
• Case Material:
Self extinguishing plastic
• Epoxy Filled
• Case Color: Black
• Base Plate Material:
Aluminum
• Circuit diagram shown on
part is terminal view.
© 2002 TELEDYNE RELAYS
NOTES:
1. UNLESS OTHERWISE SPECIFIED, TOLERANCES: .XXX = ± .005 (0.13mm);
.XX = ± .01 (0.25mm).
2. Weight: max. 3 oz.
3. BUILT IN SNUBBER (R = 100 W C = 0.01mF).
4. Output may lose blocking capabilities during and after surge until TJ falls below
maximum.
5. 100mS pulse @ 1 Hz reptitive rate at 25°C, maximum 10 cycles.
(800) 284-7007 • www.teledynerelays.com
602 83
602\072002\Q1