DIM200PKM33-F000 IGBT Chopper Module Replaces DS5865-2 DS5865-3 October 2011 (LN28813) FEATURES KEY PARAMETERS 10µs Short Circuit Withstand High Thermal Cycling Capability Soft Punch Through Silicon VCES VCE(sat) * (typ) IC (max) IC(PK) (max) Isolated AlSiC Base with AlN Substrates Lead Free Construction APPLICATIONS Choppers Motor Controllers Power Supplies Traction Auxiliaries 3300V 2.8V 200A 400A * Measured at the auxiliary terminals 1(E1/K) 2(C1) 3(A) 1 5(E ) 1 4(G ) The Powerline range of high power modules includes half bridge, chopper, dual, single and bi-directional switch configurations covering voltages from 1200V to 6500V and currents up to 2400A. The DIM200PKM33-F000 is a 3300V, n-channel enhancement mode, insulated gate bipolar transistor (IGBT) chopper module configured with the upper arm of the bridge controlled. The IGBT has a wide reverse bias safe operating area (RBSOA). This device is optimised for traction drives and other applications requiring high thermal cycling capability. 1 8(C ) Fig. 1 Circuit configuration The module incorporates an electrically isolated base plate and low inductance construction enabling circuit designers to optimise circuit layouts and utilise grounded heat sinks for safety. ORDERING INFORMATION Order As: DIM200PKM33-F000 Outline type code: P Note: When ordering, please use the complete part number (See Fig. 11 for further information) Fig. 2 Package Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures www.dynexsemi.com 1 /8 DIM200PKM33-F000 ABSOLUTE MAXIMUM RATINGS Stresses above those listed under ‘Absolute Maximum Ratings’ may cause permanent damage to the device. In extreme conditions, as with all semiconductors, this may include potentially hazardous rupture of the package. Appropriate safety precautions should always be followed. Exposure to Absolute Maximum Ratings may affect device reliability. Tcase = 25°C unless stated otherwise Symbol Parameter VCES Collector-emitter voltage VGES Gate-emitter voltage IC Test Conditions VGE = 0V Max. Units 3300 V ±20 V Continuous collector current Tcase = 90°C 200 A IC(PK) Peak collector current 1ms, Tcase = 115°C 400 A Pmax Max. transistor power dissipation Tcase = 25°C, Tj = 150°C 2.6 kW 20 kA s 20 kA s 6000 V 10 pC 2 2 It Diode I t value – IGBT Arm 2 Diode I t value – Diode Arm VR = 0, tp = 10ms, Tj = 125ºC Visol Isolation voltage – per module Commoned terminals to base plate. AC RMS, 1 min, 50Hz QPD Partial discharge – per module IEC1287, V1 = 3500V, V2 = 2600V, 50Hz RMS 2 2 THERMAL AND MECHANICAL RATINGS Internal insulation material: AlN Baseplate material: AlSiC Creepage distance: 33mm Clearance: 20mm CTI (Comparative Tracking Index): 350 Symbol Rth(j-c) Rth(j-c) Rth(c-h) Tj Tstg Parameter Thermal resistance – transistor Thermal resistance – diode (IGBT Arm) Thermal resistance – diode (Diode Arm) Thermal resistance – case to heatsink (per module) Min Typ. Max Units - - 48 °C/kW - - 96 °C/kW - - 96 °C/kW Mounting torque 5Nm (with mounting grease) - - 16 °C/kW Transistor - - 150 °C Diode - - 125 °C -40 - 125 °C Mounting – M6 - - 5 Nm Electrical connections – M5 - - 4 Nm Continuous dissipation junction to case Continuous dissipation junction to case Junction temperature Storage temperature range Screw torque 2/8 Test Conditions - Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. www.dynexsemi.com DIM200PKM33-F000 ELECTRICAL CHARACTERISTICS Tcase = 25°C unless stated otherwise. Symbol ICES Test Conditions Min Typ Max Units VGE = 0V, VCE = VCES 1 mA VGE = 0V, VCE = VCES, Tcase = 125°C 15 mA Gate leakage current VGE = ± 20V, VCE = 0V 1 μA Gate threshold voltage IC = 40mA, VGE = VCE 7.0 V Collector-emitter saturation voltage VGE = 15V, IC = 200A 2.8 V VGE = 15V, IC = 200A, Tj = 125°C 3.6 V Diode forward current DC 200 200 A tp = 1ms 400 400 A Collector cut-off current IGES VGE(TH) VCE(sat) Parameter † IF IFM VF Diode maximum forward current † Diode forward voltage (IGBT arm) ‡ Diode forward voltage (Diode arm) † Diode forward voltage (IGBT arm) ‡ Diode forward voltage (Diode arm) 5.5 6.5 2.9 V 3.0 V 3.0 V 3.1 V IF = 200A IF = 200A, Tj = 125°C Cies Input capacitance VCE = 25V, VGE = 0V, f = 1MHz 36 nF Qg Gate charge ±15V 5 μC Cres Reverse transfer capacitance VCE = 25V, VGE = 0V, f = 1MHz 0.45 nF LM Module inductance 40 nH Internal transistor resistance 500 μ 930 A RINT Tj = 125°C, VCC = 1000V SCData Short circuit current, ISC tp ≤ 10μs, VGE ≤ 15V * VCE (max) = VCES – L x dI/dt IEC 60747-9 Note: † Measured at the auxiliary terminals ‡ Measured at the power busbars * L is the circuit inductance + LM Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures www.dynexsemi.com 3 /8 DIM200PKM33-F000 ELECTRICAL CHARACTERISTICS Tcase = 25°C unless stated otherwise Symbol td(off) tf Parameter Min Turn-off delay time Fall time IC = 200A EOFF Turn-off energy loss td(on) Turn-on delay time tr Test Conditions VGE = ±15V VCE = 1800V RG(ON) = 16.5 RG(OFF) = 16.5 Cge = 56nF Rise time LS ~ 100nH RG(ON) = 7.5, RG(OFF) = 16.5 Typ. Max Units 1.95 μs 170 ns 220 mJ 1180 ns 225 ns 290 mJ 80 μC EON Turn-on energy loss Qrr Diode reverse recovery charge Irr Diode reverse recovery current VCE = 1800V 144 A Erec Diode reverse recovery energy dIF/dt = 1600A/μs 75 mJ IF = 200A Tcase = 125°C unless stated otherwise Parameter Symbol td(off) tf EOFF td(on) tr Test Conditions Turn-off delay time Fall time IC = 200A VGE = ±15V Turn-off energy loss VCE = 1800V Turn-on delay time RG(ON) = 16.5 RG(OFF) = 16.5 Cge = 56nF Rise time LS ~ 100nH RG(ON) = 7.5, RG(OFF) = 16.5 Min Typ. Max Units 2.2 μs 190 ns 265 mJ 1150 ns 280 ns 390 mJ 125 μC EON Turn-on energy loss Qrr Diode reverse recovery charge Irr Diode reverse recovery current VCE = 1800V 155 A Erec Diode reverse recovery energy dIF/dt = 1600A/μs 130 mJ 4/8 IF = 200A Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. www.dynexsemi.com DIM200PKM33-F000 Fig. 3 Typical output characteristics Fig. 4 Typical output characteristics Fig. 5 Typical switching energy vs collector current Fig. 6 Typical switching energy vs gate resistance Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures www.dynexsemi.com 5 /8 DIM200PKM33-F000 6/8 Fig. 7 Diode typical forward characteristics Fig. 8 Reverse bias safe operating area Fig. 9 Diode reverse bias safe operating area Fig. 10 Transient thermal impedance Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. www.dynexsemi.com DIM200PKM33-F000 PACKAGE DETAILS For further package information, please visit our website or contact Customer Services. All dimensions in mm, unless stated otherwise. DO NOT SCALE. Nominal Weight: 750g Module Outline Type Code: P Fig. 11 Module outline drawing Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures www.dynexsemi.com 7 /8 DIM200PKM33-F000 IMPORTANT INFORMATION: This publication is provided for information only and not for resale. The products and information in this publication are intended for use by appropriately trained technical personnel. Due to the diversity of product applications, the information contained herein is provided as a general guide only and does n ot constitute any guarantee of suitability for use in a specific application. The user must evaluate the suitability of the product and the completeness of the product data for the application. The user is responsible for product selection and ensuring all safety and any warning requirements are met. Should additional product information be needed please contact Customer Service. Although we have endeavoured to carefully compile the information in this publication it may contain inaccuracies or typographical errors. The information is provided without any warranty or guarantee of any kind. This publication is an uncontrolled document and is subject to change without notice. When referring to it please ensure that it is the most up to date version and has not been superseded. The products are not intended for use in applications where a failure or malfunction may cause loss of life, injury or damage to property. The user must ensure that appropriate safety precautions are taken to prevent or mitigate the consequences of a product failure or malfunction. The products must not be touched when operating because there is a danger of electrocution or severe burning. Always use protective safety equipment such as appropriate shields for the product and wear safety glasses. Even when disconnected any electric charge remaining in the product must be discharged and allowed to cool before safe handling using protective gloves. Extended exposure to conditions outside the product ratings may affect reliability leading to premature product failure. Use outside the product ratings is likely to cause permanent damage to the product. In extreme conditions, as with all semiconductors, this may include potentially hazardous rupture, a large current to flow or high voltage arcing, resulting in fire or explosion. Appropriate application design and safety precautions should always be followed to protect persons and property. Product Status & Product Ordering: We annotate datasheets in the top right hand corner of the front page, to indicate product status if it is not yet fully approved for production. The annotations are as follows:Target Information: This is the most tentative form of information and represents a very preliminary specification. No actual design work on the product has been started. Preliminary Information: The product design is complete and final characterisation for volume production is in progress. The datasheet represents the product as it is now understood but details may change. No Annotation: The product has been approved for production and unless otherwise notified by Dynex any product ordered will be supplied to the current version of the data sheet prevailing at the time of our order acknowledgement. All products and materials are sold and services provided subject to Dynex’s conditions of sale, which are available on request. Any brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners. HEADQUARTERS OPERATIONS CUSTOMER SERVICE DYNEX SEMICONDUCTOR LTD Doddington Road, Lincoln, Lincolnshire, LN6 3LF, United Kingdom Fax: +44(0)1522 500550 Tel: +44(0)1522 500500 Web: http://www.dynexsemi.com DYNEX SEMICONDUCTOR LTD Doddington Road, Lincoln, Lincolnshire, LN6 3LF, United Kingdom Fax: +44(0)1522 500020 Tel: +44(0)1522 502753 / 502901 Email: [email protected] Dynex Semiconductor Ltd. 2005 Technical Documentation – Not for resale. 8/8 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. www.dynexsemi.com