DCR1260F42

DCR1260F42
Phase Control Thyristor
DS5966-3 August 2014 (LN31840)
FEATURES
KEY PARAMETERS

Double Side Cooling

High Surge Capability
VDRM
IT(AV)
ITSM
dV/dt*
dI/dt
APPLICATIONS
4200V
1255A
16800A
1500V/µs
1000A/µs
* Higher dV/dt selections available

High Power Drives

High Voltage Power Supplies

Static Switches
VOLTAGE RATINGS
Part and
Ordering
Number
Repetitive Peak
Voltages
VDRM and VRRM
V
DCR1260F42
DCR1260F40
4200
4000
Conditions
Tvj = -40°C to 125°C,
IDRM = IRRM = 100mA,
VDRM, VRRM tp = 10ms,
VDSM & VRSM =
VDRM & VRRM + 100V
respectively
Outline type code: F
Lower voltage grades available.
(See Package Details for further information)
ORDERING INFORMATION
Fig. 1 Package outline
When ordering, select the required part number
shown in the Voltage Ratings selection table.
For example:
DCR1260F42
Note: Please use the complete part number when ordering
and quote this number in any future correspondence
relating to your order.
1/10
www.dynexsemi.com
DCR1260F42
SEMICONDUCTOR
CURRENT RATINGS
Tcase = 60°C unless stated otherwise
Symbol
Parameter
Test Conditions
Max.
Units
1260
A
Double Side Cooled
IT(AV)
Mean on-state current
IT(RMS)
RMS value
-
1980
A
Continuous (direct) on-state current
-
1890
A
IT
Half wave resistive load
SURGE RATINGS
Symbol
ITSM
2
It
Parameter
Surge (non-repetitive) on-state current
Test Conditions
Max.
Units
10ms half sine, Tcase = 125°C
16.8
kA
VR = 0
1.41
MA s
Min.
Max.
Units
2
I t for fusing
2
THERMAL AND MECHANICAL RATINGS
Symbol
Rth(j-c)
Rth(c-h)
Parameter
Thermal resistance – junction to case
Thermal resistance – case to heatsink
Test Conditions
Double side cooled
DC
-
0.0184
°C/W
Single side cooled
Anode DC
-
0.0333
°C/W
Cathode DC
-
0.0418
°C/W
Double side
-
0.004
°C/W
-
0.008
°C/W
-
125
°C
Clamping force 23kN
(with mounting compound)
Blocking VDRM / VRRM
Single side
Tvj
Virtual junction temperature
Tstg
Storage temperature range
-55
125
°C
Fm
Clamping force
20.0
25.0
kN
2/10
www.dynexsemi.com
DCR1260F42
SEMICONDUCTOR
DYNAMIC CHARACTERISTICS
Symbol
IRRM/IDRM
Parameter
Test Conditions
Min.
Max.
Units
Peak reverse and off-state current
At VRRM/VDRM, Tcase = 125°C
-
100
mA
dV/dt
Max. linear rate of rise of off-state voltage
To 67% VDRM, Tj = 125°C, gate open
-
1500
V/µs
dI/dt
Rate of rise of on-state current
From 67% VDRM to 2x IT(AV)
Repetitive 50Hz
-
250
A/µs
Gate source 30V, 10,
Non-repetitive
-
1000
A/µs
tr < 0.5µs, Tj = 125°C
VT(TO)
rT
tgd
Threshold voltage – Low level
300A to 850A at Tcase = 125°C
-
0.86
V
Threshold voltage – High level
850A to 4000A at Tcase = 125°C
-
1.0
V
On-state slope resistance – Low level
300A to 850A at Tcase = 125°C
-
0.611
m
On-state slope resistance – High level
850A to 4000A at Tcase = 125°C
-
0.444
m
VD = 67% VDRM, gate source 30V, 10
-
3
µs
-
800
µs
2000
3500
µC
81
121
A
Delay time
tr = 0.5µs, Tj = 25°C
tq
Turn-off time
Tj = 125°C, VR = 100V, dI/dt = 5A/µs,
dVDR/dt = 20V/µs linear to 2000V
QS
Stored charge
IRR
Reverse recovery current
IL
Latching current
Tj = 25°C, VD = 5V
-
3
A
IH
Holding current
Tj = 25°C, RG-K = , ITM = 500A, IT = 5A
-
300
mA
IT = 1000A, tp = 1000us,Tj = 125°C,
dI/dt =5A/µs,
3/10
www.dynexsemi.com
DCR1260F42
SEMICONDUCTOR
GATE TRIGGER CHARACTERISTICS AND RATINGS
Symbol
Parameter
Test Conditions
Max.
Units
VGT
Gate trigger voltage
VDRM = 5V, Tcase = 25°C
1.5
V
VGD
Gate non-trigger voltage
At 50% VDRM, Tcase = 125°C
0.4
V
IGT
Gate trigger current
VDRM = 5V, Tcase = 25°C
350
mA
IGD
Gate non-trigger current
At 50% VDRM, Tcase = 125°C
10
mA
CURVES
4500
min 25°C
min 125°C
max 25°C
max 125°C
4000
Instantaneous on-state current IT - (A)
3500
3000
2500
2000
1500
1000
500
0
0.5
1
1.5
2
2.5
3
Instantaneous on-state voltage VT - (V)
Fig.2 Maximum & minimum on-state characteristics
VTM EQUATION
VTM = A + Bln (IT) + C.IT+D.IT
Where
A = 0.259886
B = 0.122742
C = 0.000418
D = -0.002452
these values are valid for Tj = 125°C for IT 300A to 4000A
4/10
www.dynexsemi.com
DCR1260F42
SEMICONDUCTOR
130
16
180
120
90
60
30
120
110
Maximum case temperature, T case ( o C )
Mean power dissipation - (kW)
14
12
10
8
6
180
4
120
90
2
90
80
70
60
50
40
30
20
60
10
30
0
100
0
0
1000
2000
3000
4000
0
Mean on-state current, IT(AV) - (A)
500
750
1000
1250
125
12
10
Mean power dissipation - (kW)
100
75
50
25
8
6
4
d.c.
180
120
90
60
30
2
0
0
250
500
750
1000
1250
1750
Fig.4 Maximum permissible case temperature,
double side cooled – sine wave
180
120
90
60
30
0
1500
Mean on-state current, IT(AV) - (A)
Fig.3 On-state power dissipation – sine wave
Maximum heatsink temperature, THeatsink - ( ° C)
250
1500
1750
Mean on-state current, IT(AV) - (A)
Fig.5 Maximum permissible heatsink temperature,
double side cooled – sine wave
0
1000
2000
3000
4000
Mean on-state current, IT(AV) - (A)
Fig.6 On-state power dissipation – rectangular wave
5/10
www.dynexsemi.com
DCR1260F42
SEMICONDUCTOR
130
110
100
90
Maximum heatsink temperature Theatsink -(o C)
120
Maximum permissible case temperature , Tcase -(° C)
125
d.c.
180
120
90
60
30
80
70
60
50
40
30
20
10
0
d.c.
180
120
90
60
30
100
75
50
25
0
0
500
1000
1500
2000
2500
3000
0
500
Mean on-state current, IT(AV) - (A)
Double side cooled
Double Side Cooled
Thermal Impedance Zth(j-c) ( °C/kW )
2000
2500
Fig.8 Maximum permissible heatsink temperature,
double side cooled – rectangular wave
45.0
Anode side cooled
Cathode Side Cooled
Ri (°C/kW)
1
7.5608
2
4.0772
Ti (s)
0.6877
0.2537
0.0614
0.0101
Ri (°C/kW)
6.7211
4.6219
15.5387
14.8631
Ti (s)
Cathode side cooled
35.0
1500
Mean on-state current, IT(AV ) - (A)
Fig.7 Maximum permissible case temperature,
double side cooled – rectangular wave
40.0
1000
Ri (°C/kW)
Ti (s)
Anode Side Cooled
3
3.8420
4
2.8671
0.1910
0.0158
5.0011
3.3169
11.5564
8.5810
4.7942
8.3643
4.2216
6.0269
0.0166
0.2255
i 4
Z th  [ Rii(41  exp(T / Ti )]
Z th  [ Ri  (1  exp(T / Ti )]
30.0
i 1
25.0
i 1
20.0
Rth(j-c) Conduction
Tables show the increments of thermal resistance Rth(j-c) when the device
operates at conduction angles other than d.c.
15.0
10.0
5.0
0.0
0.001
0.01
0.1
1
Time ( s )
10
100
°
180
120
90
60
30
15
Double side cooling
Zth (z)
sine.
rect.
3.19
2.14
3.72
3.10
4.29
3.64
4.81
4.23
5.22
4.88
5.40
5.22
°
180
120
90
60
30
15
Anode Side Cooling
Zth (z)
sine.
rect.
2.97
2.03
3.43
2.89
3.92
3.36
4.36
3.87
4.69
4.41
4.84
4.70
Cathode Sided Cooling
Zth (z)
°
sine.
rect.
180
2.95
2.02
120
3.40
2.87
90
3.88
3.34
60
4.31
3.84
30
4.64
4.37
15
4.79
4.65
Fig.9 Maximum (limit) transient thermal impedance – junction to case (°C/kW)
6/10
www.dynexsemi.com
DCR1260F42
SEMICONDUCTOR
40
Conditions:
Tcase= 125 C
VR = 0
half-sine wave
100
35
ITSM
3
30
10
25
2
I2t
I2t (MA2s)
Surge current, ITSM - (kA)
Surge current, ITSM- (kA)
Conditions:
Tcase = 125 C
VR =0
Pulse width = 10ms
20
15
1
10
5
1
0
1
10
100
0
1
Number of cycles
Fig.10 Multi-cycle surge current
10
Pulse width, t P - (ms)
100
Fig.11 Single-cycle surge current
300
8000
Q s typical = 2272.7*(di/dt)
0.4403
Reverse recovery current, Irr - (A)
7000
Stored Charge, Qs - (uC)
6000
5000
Conditions:
Tj = 125°C,
V peak ~ 2750V
Vrm ~ 2000V
snubber as appropriate to
control reverse voltage
4000
3000
2000
250
IRR typical = 40.393*(di/dt) 0.6964
200
150
Conditions:
Tj = 125°C,
V peak ~ 2750V
Vrm ~ 2000V
snubber as appropriate to
control reverse voltage
100
50
1000
0
0
0
5
10
15
Rate of decay of on-state current, di/dt - (A/us)
Fig.12 Stored charge vs di/dt
20
0
5
10
15
20
Rate of decay of on-state current, di/dt - (A/us)
Fig.13 Reverse recovery current vs di/dt
7/10
www.dynexsemi.com
DCR1260F42
SEMICONDUCTOR
10
9
Gate trigger voltage, V GT - (V)
8
7
Upper Limit
6
5
Preferred gate drive
4
3
Tj = -40oC
2
Lower Limit
Tj = 25oC
1
Tj = 125oC
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Gate trigger current I GT , - (A)
Fig14 Gate Characteristics
30
Lower Limit
Upper Limit
5W
Gate trigger voltage, VGT - (V)
25
10W
20W
50W
20
100W
150W
-40C
15
10
5
0
0
1
2
3
4
5
6
7
8
9
10
Gate trigger current, I GT - (A)
Fig. 15 Gate characteristics
8/10
www.dynexsemi.com
DCR1260F42
SEMICONDUCTOR
PACKAGE DETAILS
For further package information, please contact Customer Services. All dimensions in mm, unless stated otherwise.
DO NOT SCALE.
3rd ANGLE PROJECTION
DO NOT SCALE
IF IN DOUBT ASK
HOLE Ø3.60 X 2.00
DEEP (IN BOTH
ELECTRODES)
20° OFFSET (NOM.)
TO GATE TUBE
Ø73.0 MAX
Ø47.0 NOM
Ø1.5
CATHODE
GATE
ANODE
Ø47.0 NOM
FOR PACKAGE HEIGHT
SEE TABLE
Device
DCR1003SF18
DCR1006SF28
DCR1008SF36
DCR1020F65
DCR1050SF42
DCR1110F52
DCR1180F52
DCR1260F42
DCR1274SF18
DCR1275SF28
DCR1277SF36
DCR1279SF48
DCR1350F42
DCR1610F28
DCR1640F28
DCR1770F22
DCR1830F22
DCR750F85
DCR810F85
DCR840F48
DCR890F65
DCR950F65
Maximum Minimum
Thickness Thickness
(mm)
(mm)
26.415
25.865
26.49
25.94
26.72
26.17
27.1
26.55
26.72
26.17
26.84
26.29
26.84
26.29
26.72
26.17
26.415
25.865
26.49
25.94
26.72
26.17
26.84
26.29
26.72
26.17
26.49
25.94
26.49
25.94
26.415
25.865
26.415
25.865
27.46
26.91
27.46
26.91
26.84
26.29
27.1
26.5
27.1
26.5
Lead length: 420mm
Lead terminal connector: M4 ring
Package outline type code: F
Fig.16 Package outline
9/10
www.dynexsemi.com
DCR1260F42
SEMICONDUCTOR
IMPORTANT INFORMATION:
This publication is provided for information only and not for resale.
The products and information in this publication are intended for use by appropriately trained technical personnel.
Due to the diversity of product applications, the information contained herein is provided as a general guide only and does not constitute
any guarantee of suitability for use in a specific application.The user must evaluate the suitability of the product and the completeness of
the product data for the application. The user is responsible for product selection and ensuring all safety and any warning requirements
are met. Should additional product information be needed please contact Customer Service.
Although we have endeavoured to carefully compile the information in this publication it may contain inaccuracies or typographical
errors. The information is provided without any warranty or guarantee of any kind.
This publication is an uncontrolled document and is subject to change without notice. When referring to it please ensure that it is the
most up to date version and has not been superseded.
The products are not intended for use in applications where a failure or malfunction may cause loss of life, injury or damage to property.
The user must ensure that appropriate safety precautions are taken to prevent or mitigate the consequences of a product failure or
malfunction.
The products must not be touched when operating because there is a danger of electrocution or severe burning. Always use
protective safety equipment such as appropriate shields for the product and wear safety glasses. Even when disconnected any
electric charge remaining in the product must be discharged and allowed to cool before safe handling using protective gloves.
Extended exposure to conditions outside the product ratings may affect reliability leading to premature product failure. Use outside the
product ratings is likely to cause permanent damage to the product. In extreme conditions, as with all semiconductors, this may include
potentially hazardous rupture, a large current to flow or high voltage arcing, resulting in fire or explosion. Appropriate application design
and safety precautions should always be followed to protect persons and property.
Product Status & Product Ordering:
We annotate datasheets in the top right hand corner of the front page, to indicate product status if it is not yet fully approved for
production. The annotations are as follows:Target Information:
Preliminary Information:
No Annotation:
This is the most tentative form of information and represents a very preliminary specification.
No actual design work on the product has been started.
The product design is complete and final characterisation for volume production is in
progress.The datasheet represents the product as it is now understood but details may change.
The product has been approved for production and unless otherwise notified by Dynex any
product ordered will be supplied to the current version of the data sheet prevailing at the
time of our order acknowledgement.
All products and materials are sold and services provided subject to Dynex’s conditions of sale, which are available on request.
Any brand names and product names used in this publication are trademarks, registered trademarks or trade names of their
respective owners.
HEADQUARTERS OPERATIONS
CUSTOMER SERVICE
DYNEX SEMICONDUCTOR LIMITED
Doddington Road, Lincoln, Lincolnshire, LN6 3LF
United Kingdom.
Phone: +44 (0) 1522 500500
Fax:
+44 (0) 1522 500550
Web: http://www.dynexsemi.com
Phone: +44 (0) 1522 502753 / 502901
Fax:
+44 (0) 1522 500020
e-mail: [email protected]
 Dynex Semiconductor Ltd.
Technical Documentation – Not for resale.
10/10
www.dynexsemi.com