Download

Safety Limit Switch
D4B-@N
CSM_D4B-_N_DS_E_10_3
Robust safety limit switch with metal housing
Slow-action and snap-action contact with
certified direct opening operation
certification
• Direct opening mechanism (NC contacts only) added to
enable opening contacts when faults occur, such as fused
contacts.
• Safety of lever settings ensured using a mechanism that
engages a gear between the operating position indicator plate
and the lever.
• Equipped with a mechanism that indicates the applicable
operating zone, as well as push-button switching to control left
and right motion.
• Head seal structure strengthened to improve seal properties
(TÜV: IEC IP67, UL: NEMA 3, 4, 4X, 6P, and 13).
• Wide standard operating temperature range:
–40 to 80°C (standard type).
• Certified standards: UL, CSA, EN (TÜV), and CCC.
Note: Contact your sales representative for details on
models with safety standard certification.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Be sure to read the “Safety Precautions” on page 9.
Model Number Structure
Model Number Legend
D4B-@@@@N
1 2
3
1. Conduit size
2: G1/2 (PF1/2) (1-conduit)
4: M20 (1 conduit)
2. Built-in Switch
1: 1NC/1NO (snap-action)
5: 1NC/1NO (slow-action)
A: 2NC (slow-action)
3. Actuator
11: Roller lever (resin roller)
15: Roller lever (stainless steel roller)
16: Adjustable roller lever
17: Adjustable rod lever
70: Plunger
71: Roller plunger
1
D4B-@N
Ordering Information
Set Model Numbers
Consult with your OMRON representative when ordering any models that are not listed in this table.
Safety Limit Switches (with Direct Opening Mechanism)
1NC/1NO (Snap-action)
Actuator
Conduit openings
Model
Direct
opening
1NC/1NO (Slow-action)
Model
Direct
opening
2NC (Slow-action)
Model
Roller lever
(resin roller)
G1/2 (PF1/2)
D4B-2111N
D4B-2511N
D4B-2A11N
M20
D4B-4111N
D4B-4511N
D4B-4A11N
Roller lever
(stainless steel
roller)
G1/2 (PF1/2)
D4B-2115N
D4B-2515N
D4B-2A15N
M20
D4B-4115N
D4B-4515N
D4B-4A15N
G1/2 (PF1/2)
D4B-2170N
D4B-2570N
D4B-2A70N
M20
D4B-4170N
D4B-4570N
D4B-4A70N
G1/2 (PF1/2)
D4B-2171N
D4B-2571N
D4B-2A71N
M20
D4B-4171N
D4B-4571N
D4B-4A71N
Plunger
Roller plunger
Direct
opening
General-purpose Limit Switches
1NC/1NO (Snap-action)
Actuator
Adjustable roller
lever
Adjustable rod
lever
Conduit openings
G1/2 (PF1/2)
Model
Direct
opening
D4B-2116N
1NC/1NO (Slow-action)
Model
D4B-2516N
--M20
D4B-4116N
G1/2 (PF1/2)
D4B-2117N
D4B-4117N
2NC (Slow-action)
Model
D4B-4516N
--D4B-4A16N
D4B-2517N
D4B-2A17N
---
D4B-4517N
Direct
opening
D4B-2A16N
---
--M20
Direct
opening
--D4B-4A17N
Note: Consult your OMRON representative for products.
2
D4B-@N
Specifications
Standards and EC Directives
Conforms to the following EC Directives:
•
•
•
•
•
Machinery Directive
Low Voltage Directive
EN50041
EN60204-1
EN ISO 14119
Certified Standards
Snap-action Models
Certification body
TÜV Rheinland
Slow-action Models
Standard
EN60947-5-1
(certified direct
opening mechanism)
GS-ET-15
File No.
Certification body
Consult your
OMRON
representative for
details.
TÜV Rheinland
EN60947-5-1
(uncertified direct
J50005477 *
opening mechanism)
Standard
EN60947-5-1
(certified direct
opening mechanism)
GS-ET-15
File No.
Consult your
OMRON
representative for
details.
EN60947-5-1
(uncertified direct
J50005477 *
opening mechanism)
UL
UL508
E76675
UL
UL508
E76675
CSA
C22.2 No. 14
LR45746
CSA
C22.2 No. 14
LR45746
CQC (CCC)
GB14048.5
2003010305077612
2003010305095927
CQC (CCC)
GB14048.5
2003010305077612
2003010305095927
* Adjustable roller lever, adjustable rod lever only.
* Adjustable roller lever, adjustable rod lever only.
Certified Standard Ratings
TÜV (EN60947-5-1), CCC (GB14048.5)
Item
Utilization category AC-15
Rated operating current (Ie)
2A
Rated operating voltage (Ue)
400 V
Note: As protection against short-circuiting, use either a gI-type or gG-type 10 A fuse that conforms to IEC60269.
UL/CSA: (UL508, CSA C22.2 No. 14)
A600
Rated voltage
120 VAC
240 VAC
480 VAC
600 VAC
Current (A)
Carry current
10 A
Make
60
30
15
12
Volt-amperes (VA)
Break
6
3
1.5
1.2
Make
7,200
Break
720
3
D4B-@N
Ratings
Non-inductive load (A)
Rated voltage (V)
Resistive load
NC
Inductive load (A)
Lamp load
NO
NC
Inductive load
NO
NC
Motor load
NO
NC
125 VAC
250
400
10
10
10
3
2
1.5
1.5
1
0.8
10
10
3
5
3
1.5
8 VDC
14
30
125
250
10
10
6
0.8
0.4
6
6
4
0.2
0.1
3
3
3
0.2
0.1
10
10
6
0.8
0.4
6
6
4
0.2
0.1
Note: 1.
2.
3.
4.
NO
2.5
1.5
0.8
The above values are continuous currents.
Inductive loads have a power factor of 0.4 or higher (AC) or a time constant of 7 ms or lower (DC).
Lamp loads have a inrush current of 10 times the normal current.
Motor loads have a inrush current of 6 times the normal current.
Inrush current
30 A max.
Characteristics
Degree of protection *1
Durability *2
IP67 (EN60947-5-1)
Mechanical
Electrical
Operating speed
Operating frequency
30,000,000 operations min. (snap-action)
10,000,000 operations min. (slow-action)
500,000 operations min. (10 A resistive load at 250 VAC)
1 mm/s to 0.5 m/s
Mechanical
Electrical
120 operations/minute
30 operations/minute
Contact resistance
25 mΩ max.
Minimum applicable load *3
180 mA resistive load at 5 VAC
(N-level reference value)
Rated insulation voltage (Ui)
600 V (EN60947-5-1)
Rated frequency
50/60 Hz
Protection against electric shock
Class I (with ground terminal)
Pollution degree (operating environment)
3 (EN60947-5-1)
Between terminals
of same polarity
Impulse withstand voltage Between terminals
(EN60947-5-1)
of different polarity
2.5 kV (snap-action)/4 kV (slow-action)
4 kV (slow-action)
Between each
4 kV
terminal and ground
Insulation resistance
100 MΩ min. (at 500 VDC) between terminals of the same polarity and between each
terminal and non-current-carrying part
Contact gap
2 × 2 mm min. (slow-action)
2 × 0.5 mm min. (snap-action)
Vibration resistance
Shock resistance
Malfunction
10 to 55 Hz, 0.75 mm single amplitude
Destruction
1,000 m/s2 min.
Malfunction
300 m/s2 min.
Conditional short-circuit current
100 A (EN60947-5-1)
Conventional enclosed thermal current (Ithe)
20 A (EN60947-5-1)
Ambient operating temperature
–40 to 80°C (with no icing)
Ambient operating humidity
95% max.
Weight
Approx. 250 g
Note: 1. The above values are initial values.
2. The above values may vary depending on the model. Consult your OMRON sales representative for details.
*1. The degree of protection is tested using the method specified by the standard (EN60947-5-1). Confirm that sealing properties are sufficient for
the operating conditions and environment beforehand.
*2. The durability is for an ambient temperature of 5 to 35°C and ambient humidity of 40% to 70%. For further conditions, consult your OMRON
sales representative.
*3. The above values may vary depending on switching frequency, environmental condition, and relativity level, consult your OMRON sales
representative.
4
D4B-@N
Engineering Data
Electrical Durability (Snap-action)
(Ambient temperature: 5 to 30°C, ambient humidity: 40 to 70%)
(cosφ = 0.4)
1,000
500
125 VAC
Operating frequencies:
30 times/min., cosφ = 1
300
250 VAC
480 VAC
100
Operations (x 104)
Operations (x 104)
(cosφ = 1)
1,000
500
300
250 VAC
100
50
50
30
30
10
10
Switching current (A)
Operating frequencies:
30 times/min., cosφ = 0.4
500 VAC
Switching current (A)
Structure and Nomenclature
Structure
Head
Can be connected in any of four directions (except for
Roller Plunger Models, which can be connected at either
of 2 directions that differ by 90°)
The roller lever switch employs a
system which allows
selection of operation on only one
side (left or right)
or both sides without the use of
any tools.
Seal Ring
Sealing properties improved by using a X ring and
bearing-free structure.
Roller
Nylon rollers used for superior resistance to wear.
Lever (Form Lock Structure)
The lever has an operating position indication plate
and grooves that mate every 90° to prevent slipping
between the rotary axis and lever.
The operating position indicator plate
Built-in Switch
Direct opening mechanism used for NC contact to
separate contact for faults, such as contact welding.
The heights of the NC and NO terminals are different
to enable easier wiring.
Conduit Opening
G1/2 or M20
Cover
Ground Screw
Ground screws are provided on all
models for increased safety.
5
D4B-@N
Direct Opening Mechanism
1NO/1NC Contact (Snap-action)
Conforms to EN60947-5-1 Direct Opening
(Only NC contact has a direct opening mechanism.)
1. When contact welding occurs.
2. When contacts are being pulled apart.
Movable contact
Safety cam directly
pushes up the
movable contact
blade.
Movable contact
blade
B
Plunger
A
3. When contacts are completely
pulled apart.
Safety cam
Fixed contact (NC)
1NC/1NO Contact (Slow-action)
2NC Contact (Slow-action)
Conforms to EN60947-5-1 Direct Opening
(Only NC contact has a direct opening mechanism.)
When contact welding occurs, the contacts are separated
from each other by the plunger being pushed in.
Conforms to EN60947-5-1 Direct Opening
(Both NC contacts have a direct opening mechanism.)
When contact welding occurs, the contacts are separated
from each other by the plunger being pushed in.
Fixed contact (NC)
Contact spring
Fixed contact (NC)
Plunger
Return spring
Movable contact
Plunger
Contact spring
Movable contact
Return spring
Fixed contact (NO)
Contact Form
Model
Contact
Contact form
Za
D4B-@1@N
1NC/1NO
(Snap-action)
13
14
Diagrams
11-12
ON
13-14
11
Explanation
Terminal numbers 11-12 and
13-14 cannot be used as unlike
poles.
Stroke
12
Zb
D4B-@5@N
1NC/1NO
(Slow-action)
11
12
11-12
ON
23-24
23
Zb
D4B-@A@N
2NC
(Slow-action)
11-12
11
21
12
22
ON
21-22
Stroke
Only NC contact 11-12 has a
certified direct opening
mechanism.
Terminal numbers 11-12 or
23-24 can be used as unlike
poles.
Stroke
24
Only NC contact 11-12 has a
certified direct opening
mechanism.
Both NC contacts 11-12 and
21-22 have a certified direct
opening mechanism.
Terminal numbers 11-12 and
21-22 can be used as unlike
poles.
Note: Terminal numbers are according to EN50013; contact symbols are according to IEC60947-5-1.
6
D4B-@N
Dimensions and Operating Characteristics
(Unit: mm)
Note: Omitted dimensions are the same as those for the Roller Lever Type Models
D4B-2@@@N have a G1/2 conduit opening.
D4B-4@@@N have a M20 conduit opening.
Switches
Roller Lever
D4B-@@11N
Roller Lever (Stainless Steel Roller)
D4B-@@15N 17.5 × 7 stainless steel roller
62±1
17.5 dia. × 6.6 resin roller
PT
21° ±3°
M5 × 12
56
28.3
Allen-head bolt
Four, M3.5 × 19.5
head
mounting screws
31.5R
Set position
indicator plate
*1
23
131.3±1.2
60±0.2
11.5
131.3±1.2
77
15
30±0.2
60±0.2
+1
0
Adjustable Roller Lever *2
D4B-@@16N
19 dia. × 7
resin roller
25 to 89R
28.3
Four, M3.5 × 24.5
head
mounting screws
3 dia. × 160
stainless steel
rod
74
15
30±0.2
+1
0
74
30±0.2
40
43
77
7.3
5.3
Conduit opening
31.5
40
99.5
Two, M4 × 12 cover
mounting screws Cover
8
5.3
22.5
Two, 5.3-dia.
mounting holes
60±0.2
7.3
8
Four, M3.5 × 24.5
head
mounting screws
M5 × 12
Allen-head bolts
99.5
Two, M4 × 12 cover
mounting screws
Cover
16
Setting position
indicator *1
23
77
56.8
28.3
145 max.
22.5
Two, 5.3-dia.
mounting holes
3
60±0.2
66±1
5.4
16
Conduit opening
43
Adjustable Rod Lever *2
D4B-@@17N
M5 × 16
Allen-head bolts
2
23
+1
0
Set position
indicator plate *1
1
15
31.5
40
64.4
77
7.3
30±0.2
71±1
53
46.8
99.5
74
5.3
Conduit opening
31.5
43
40
22.5
Two, 5.3 dia.
mounting holes
Two, M4 × 12
cover mounting
screws
Cover
8
5.3
Four, M3.5 × 19.5
head
mounting screws
11.5
99.5
7.3
8
16
Set position
indicator plate *1
23
74
56
28.3
31.5R
22.5
Two, 5.3-dia.
mounting holes
Two, M4 × 12
cover mounting
Cover
screws
62±1
PT
21°±3° M5 × 12
Allen-head bolt
16
+1
0
15
Conduit opening
31.5
43
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
*1. The lever can be set to any desired position by turning the operating position indicator.
*2. In terms of construction, the Switch is a General-purpose Limit Switch rather than a Safety Limit Switch.
Operating characteristics
Operating force
Release force
Pretravel
Overtravel
Movement differential
Direct opening travel
Direct opening force
Total travel
Model D4B-@@11N D4B-@@15N D4B-@@16N D4B-@@17N
*1
*2
OF max.
RF min.
PT
PT (2nd) *3 *5
OT min.
MD max. *4
DOT min. *3 *6
*4 *6
DOF min. *6
TT *5
9.41N
1.47N
21°±3°
(45°)
50°
12°
35°
55°
19.61N
(75°)
9.41N
1.47N
21°±3°
(45°)
50°
12°
35°
55°
19.61N
(75°)
9.41N
1.47N
21°±3°
(45°)
50°
12°
35°
55°
19.61N
(75°)
2.12N
0.29N
21°±3°
(45°)
50°
12°
35°
55°
19.61N
(75°)
Note: Variation occurs in the simultaneity of contact opening/closing operations of 2NC contacts. Check contact operation.
*1. The operating characteristics of these Switches were measured with the roller level set at 31.5 mm.
*2. The operating characteristics of these Switches were measured with the rod level set at 140 mm.
*3. Only for slow-action models.
*4. Only for snap-action models.
*5. Reference values.
*6. Must be provided to ensure safe operation.
7
D4B-@N
Plunger
D4B-@@70N
Roller Plunger
D4B-@@71N
16
PT
9.2 dia.
Stainless steel
plunger
Four, M3.5 × 19.5
head
mounting screws
Two, 5.3-dia.
mounting holes
74
77
8
5.3
15
30±0.2
40
Conduit opening
97
74
5.3
30±0.2
31.5
+1
0
20
Two, M4 × 12 cover
mounting screws
Cover
7.3
60±0.2
7.3
8
Four, M3.5 × 19.5
head
mounting screws
Two, 5.3-dia.
mounting holes
97
Two, M4 × 12 cover
mounting screws
Cover
16
9.2 dia.
OP
20
OP
60±0.2
12.7 dia. × 4.8
stainless steel roller
PT
+1
0
43
40
15
77
Conduit opening
31.5
43
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
Operating characteristics
Operating force
Release force
Pretravel
Model
D4B-@@70N
D4B-@@71N
Overtravel
Movement differential
Direct opening travel
Direct opening force
Total travel
OF max.
RF min.
PT max.
PT (2nd) *1 *3
OT min.
MD max. *2
DOT min. *4
DOF min. *4
TT *3
18.63 N
1.96 N
2 mm
(3 mm)
5 mm
1 mm
3.2 mm
49.03 N
(7 mm)
18.63 N
1.96 N
2 mm
(3 mm)
5 mm
1 mm
3.2 mm
49.03N
(7 mm)
Free position
Operating position
FP max.
OP
38 mm
35±1 mm
51 mm
48±1 mm
Note: Variation occurs in the simultaneity of
contact opening/closing operations of
2NC contacts. Check contact
operation.
*1. Only for slow-action models.
*2. Only for snap-action models.
*3. Reference values.
*4. Must be provided to ensure safe
operation.
8
D4B-@N
Application Precaution
Changing the Operating Direction
Operating section
(on back of Head)
Switches with Roller Levers
The operating direction of the lever can be easily
changed without using any tools. It can be set to
clockwise operation (CW) or counterclockwise
(CCW) operation.
Use the procedure given at the right to change
the operating direction.
Operating procedure
1. Remove the four Head set screws and remove the Head
from the Switch Box.
Head Cover
Operating
position
mark
(arrow)
2. Turn the bottom of the Head toward you, press in the Head
Cover shown in the diagram at the left, and turn the Cover
clockwise or counterclockwise.
Note: The factory setting is for “CW.CCW.”
3. The “CW” setting is for clockwise operation and the “CCW”
setting is for counterclockwise operation. Set the Cover to
the desired position.
Safety Precautions
Be sure to read the precautions for All Safety Limit Switches in the website at:http://www.ia.omron.com/.
Indication and Meaning for Safe Use
Mounting
Precautions
for Safe Use
Supplementary comments on what to do
or avoid doing, to use the product safely.
Precautions
for Correct
Use
Supplementary comments on what to do
or avoid doing, to prevent failure to
operate, or undesirable effect on product
performance.
Use four M5 screws with washers to mount the standard model. Be
sure to apply the proper torque to tighten each screw.
Mounting Dimensions (M5)
Standard Model
Precautions for Safe Use
• Do not use the Switch submerged in oil or water, or in locations
continuously subject to splashes of oil or water. Doing so may
result in oil or water entering the Switch interior. (The IP67 degree
of protection specification for the Switch refers to water penetration
while the Switch is submersed in water for a specified period of
time.)
• Always attach the cover after completing wiring and before using
the Switch. Also, do not turn ON the Switch with the cover open.
Doing so may result in electric shock.
Precautions for Correct Use
Appropriate Tightening Torque
(3)
(6)
Be sure to tighten each
screw of the D4B-@N
properly, otherwise the
D4B-@N may malfunction.
(4)
(1)
60
30
Changes in Actuator Mounting Position
• To change the angle of the lever, loosen the Allen-head bolts on
the side of the lever.
• The operating position indicator plate * has protruding parts which
engage with the lever, thus allowing changes to the lever position
by 90°.
• The back of the operating position indicator plate * has no
protruding parts. If this plate is turned over and attached, any angle
within a 360° range can be set. Do not turn over the plate, however,
when using the D4B-@N as a switch with a certified direct opening
mechanism. For an SUVA- or BIA-certified application, make sure
that the lever engages with the operating position indicator plate
securely so that the lever will not slip.
* The operating position indicator plate: Refer to page 5.
Changes in Head Mounting Position
By removing the screws on the four corners of the head, the head can
be reset in any of four directions. Make sure that no foreign materials
will penetrate through the head.
(5)
Type
1 M3.5 terminal screw
(2)
Appropriate tightening
torque
0.59 to 0.78 N·m
2 Cover mounting screw *
1.18 to 1.37 N·m
3 Head mounting screw
0.78 to 0.88 N·m
4 M5 body mounting screw
4.90 to 5.88 N·m
5 Connector
1.77 to 2.16 N·m
Lever Mounting Screws (Roller
6
4.90 to 5.88 N·m
Levers)
9
D4B-@N
Wiring
Conduit Opening
Do not connect the bare lead wires directly to the terminals but be
sure to connect each of them by using an insulation tube and M3.5
round crimp terminals and tighten each terminal screw within the
specified torque range.
The proper lead wire is 20 to 14 AWG (0.5 to 2.5 mm2) in size.
dz dia.:
D dia.:
B:
L:
F:
l:
• Make sure that each connector is tightened within the specified
torque range.
The casing may be damaged if the connector is tightened
excessively.
• Use an OMRON SC-series Connector (sold separately) that is
suited to the cable in diameter.
Others
3.7 mm
4.5 mm
7.0 mm
20.2 mm D dia.
7.7 mm
9.0 mm
• The load for the actuator (roller) of the Switch must be imposed on
the actuator in the horizontal direction, otherwise the actuator or
the rotating axis may be deformed or damaged.
Correct
Incorrect
dz dia.
Make sure that all crimp terminals come into contact with the casing
or cover as shown below, otherwise the cover may not be mounted
properly or the D4B-@N may malfunction.
Correct
Crimp terminal
Terminal screw
Cover
Cover
Casing
θ
θ
Incorrect
Terminal screw
Crimp
terminal
Dog
• When using a long lever model, the D4B-@@16N or D4B-@@17N, the
Switch may telegraph. To avoid telegraphing, take the following
precautions.
1. Set the lever to operate in one direction.
2. Modify the rear end of the dog to an angle of 15° to 30° as
shown below or to a secondary-degree curve.
Incorrect
Terminal screw
Correct
Dog
θ ≥ 30°
15° ≤ θ ≤ 30°
3. Modify the circuit so as not to detect the wrong operating
signals.
Crimp terminal
Casing
Correct
Crimp terminal
Incorrect
Crimp terminal
10
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2015.10
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2015 All Right Reserved.