PIN Diodes MA27P07 Silicon planar type For high frequency switch 0.12+0.05 –0.02 Reverse voltage VR 60 V Forward current IF 100 mA Power dissipation PD 150 mW Junction temperature Tj 150 °C Storage temperature Tstg −55 to +150 °C 0.60±0.05 5° 0.15 min. 0.52±0.03 Unit 0.15 min. 2 Rating 0 to 0.01 Symbol 0.15 max. ■ Absolute Maximum Ratings Ta = 25°C 5° 1.00±0.05 • Low terminal capacitance: Ct ≤ 0.35 pF • Low forward dynamic resistance: rf ≤ 1.5 Ω 1.40±0.05 1 ■ Features Parameter Unit: mm 0.27+0.05 –0.02 1: Anode 2: Cathode SSSMini2-F2 Package Marking Symbol: K ■ Electrical Characteristics Ta = 25°C ± 3°C Parameter Symbol Conditions Min Typ Max Unit Forward voltage VF IF = 10 mA 1.0 V Reverse current IR VR = 60 V 100 nA Terminal capacitance Ct VR = 1 V, f = 1 MHz 0.35 pF Forward dynamic resistance rf IF = 10 mA, f = 100 MHz 1.5 Ω Note) Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7031 measuring methods for diodes. Publication date: September 2003 SKL00016AED 1 MA27P07 IF V F I R VR 103 10−1 Ta = 25°C Ct VR 0.5 Ta = 25°C Ta = 25°C f = 1 MHz 10 1 10−1 Terminal capacitance Ct (pF) Reverse current IR (nA) Forward current IF (mA) 102 10−2 10−3 10−2 10−4 10−3 0 0.2 0.4 0.6 0.8 1.0 1.2 10 20 30 40 rf I F Forward dynamic resistance rf (Ω) 103 Ta = 25°C f = 100 MHz 102 10 1 10−1 10−2 10−1 1 10 Forward current IF (mA) 2 0.3 0.2 0.1 0 0 50 Reverse voltage VR (V) Forward voltage VF (V) 0.4 SKL00016AED 60 0 10 20 30 40 Reverse voltage VR (V) 50 Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technical information described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2003 SEP