EVB72013 433MHz Transmitter Evaluation Board Description Features Frequency range from 425 MHz to 445 MHz Fully integrated PLL-stabilized VCO Single-ended RF output FSK via crystal pulling Wideband FSK deviation possible ASK/OOK via power amplifier modulation Wide power supply range from 1.95 V to 5.5 V Very low standby current Low voltage detector High over-all frequency accuracy FSK deviation and center frequency independently adjustable Data rates from DC to 40 kbps Adjustable output power range from -14 dBm to +11 dBm Adjustable current consumption from 3.8 mA to 16.8 mA Conforms to EN 300 220 and similar standards 8-pin Small Outline Integrated Circuit (SOIC) Ordering Information Part No. (see paragraph 5) EVB72013-433-FSK-C Application Examples Evaluation Board Example RF remote controls Automatic meter reading (AMR) Tire pressure monitoring systems (TPMS) Remote keyless entry (RKE) Alarm and security systems Garage door openers Home automation General Description The MLX72013 evaluation board is designed to demonstrate the performance of the transmitter IC for conductive measurements. The power amplifier is matched to 50 Ohms by means of a π-matching network to operate at a resonant frequency of 433 MHz. 39012 7201301 Rev. 001 Page 1 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description Document Content 1 2 3 Theory of Operation ...................................................................................................3 1.1 General ............................................................................................................................. 3 1.2 Block Diagram .................................................................................................................. 3 Functional Description ..............................................................................................4 2.1 Crystal Oscillator .............................................................................................................. 4 2.2 FSK Modulation ................................................................................................................ 4 2.3 Crystal Pulling................................................................................................................... 4 2.4 ASK Modulation ................................................................................................................ 5 2.5 Output Power Selection .................................................................................................... 5 2.6 Lock Detection.................................................................................................................. 5 2.7 Low Voltage Detection...................................................................................................... 5 2.8 Mode Control Logic .......................................................................................................... 6 2.9 Timing Diagrams .............................................................................................................. 6 50Ω Connector Board Circuit Diagram.....................................................................7 3.1 Board Component Values to Fig. 7 .................................................................................. 7 3.2 50Ω Connector Board PCB Top View .............................................................................. 8 3.3 Board Connection ............................................................................................................. 8 4 Evaluation Board Layouts .........................................................................................9 5 Board Variants............................................................................................................9 6 Package Description ................................................................................................10 6.1 7 Soldering Information ..................................................................................................... 10 Disclaimer .................................................................................................................12 39012 7201301 Rev. 001 Page 2 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description 1 Theory of Operation 1.1 General As depicted in Fig.1, the MLX72013 transmitter consists of a fully integrated voltage-controlled oscillator (VCO), a divide-by-16 divider (div16), a phase-frequency detector (PFD) and a charge pump (CP). An internal loop filter determines the dynamic behavior of the PLL and suppresses reference spurious signals. A Colpitts crystal oscillator (XOSC) is used as the reference oscillator of a phase-locked loop (PLL) synthesizer. The VCO’s output signal feeds the power amplifier (PA). The RF signal power Pout can be adjusted in four steps from Pout = –14 dBm to +11 dBm, either by changing the value of resistor RPS or by varying the voltage VPS at pin PSEL. The open-collector output (OUT) can be used either to directly drive a loop antenna or to be matched to a 50Ohm load. Bandgap biasing ensures stable operation of the IC at a power supply range of 1.95 V to 5.5 V. 1.2 Block Diagram RPS VCC PSEL 6 ENTX ROI 4 m ode control 16 3 XTAL 5 PLL PA 7 OUT ante nna matc hing network PFD XOSC XBUF CP VC O lo w voltage dete ctor FSKSW 2 CX2 CX1 1 FSKDTA 8 VEE Fig. 1: Block diagram with external components 39012 7201301 Rev. 001 Page 3 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description 2 Functional Description 2.1 Crystal Oscillator A Colpitts crystal oscillator with integrated functional capacitors is used as the reference oscillator for the PLL synthesizer. The equivalent input capacitance CRO offered by the crystal oscillator input pin ROI is about 18pF. The crystal oscillator is provided with an amplitude control loop in order to have a very stable frequency over the specified supply voltage and temperature range in combination with a short start-up time. 2.2 FSK Modulation FSK modulation can be achieved by pulling the crystal oscillator frequency. A CMOScompatible data stream applied at the pin FSKDTA digitally modulates the XOSC via an integrated NMOS switch. Two external pulling capacitors CX1 and CX2 allow the FSK deviation Δf and the center frequency fc to be adjusted independently. At FSKDTA = 0, CX2 is connected in parallel to CX1 leading to the lowfrequency component of the FSK spectrum (fmin); while at FSKDTA = 1, CX2 is deactivated and the XOSC is set to its high frequency fmax. An external reference signal can be directly ACcoupled to the reference oscillator input pin ROI. Then the transmitter is used without a crystal. Now the reference signal sets the carrier frequency and may also contain the FSK (or FM) modulation. Fig. 2: Crystal pulling circuitry VCC ROI XTAL FSKSW CX2 CX1 VEE FSKDTA Description 0 fmin= fc - Δf (FSK switch is closed) 1 fmax= fc + Δf (FSK switch is open) 2.3 Crystal Pulling A crystal is tuned by the manufacturer to the required oscillation frequency f0 at a given load capacitance CL and within the specified calibration tolerance. The only way to pull the oscillation frequency is to vary the effective load capacitance CLeff seen by the crystal. Figure 3 shows the oscillation frequency of a crystal as a function of the effective load capacitance. This capacitance changes in accordance with the logic level of FSKDTA around the specified load capacitance. The figure illustrates the relationship between the external pulling capacitors and the frequency deviation. It can also be seen that the pulling sensitivity increases with the reduction of CL. Therefore, applications with a high frequency deviation require a low load capacitance. For narrow band FSK applications, a higher load capacitance could be chosen in order to reduce the frequency drift caused by the tolerances of the chip and the external pulling capacitors. 39012 7201301 Rev. 001 f XTAL L1 f max C1 C0 CL eff R1 fc f min CX1 CRO CX1+CRO CL (CX1+CX2) CRO CX1+CX2+CRO CL eff Fig. 3: Crystal pulling characteristic Page 4 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description 2.4 ASK Modulation The MLX72013 can be ASK-modulated by applying data directly at pin PSEL. This turns the PA on and off and therefore leads to an ASK signal at the output. 2.5 Output Power Selection The transmitter is provided with an output power selection feature. There are four predefined output power steps and one off-step accessible via the power selection pin PSEL. A digital power step adjustment was chosen because of its high accuracy and stability. The number of steps and the step sizes as well as the corresponding power levels are selected to cover a wide spectrum of different applications. The implementation of the output power control logic is shown in figure 4. There are two matched current sources with an amount of about 8 µA. One current source is directly applied to the PSEL pin. The other current source is used for the generation of reference voltages with a resistor ladder. These reference voltages are defining the thresholds between the power steps. The four comparators deliver thermometer-coded control signals depending on the voltage level at the pin PSEL. In order to have a certain amount of ripple tolerance in a noisy environment the comparators are provided with a little hysteresis of about 20 mV. With these control signals, weighted current sources of the power amplifier are switched on or off to set the desired output power level (Digitally Controlled Current Source). The LOCK signal and the output of the low voltage detector are gating this current source. RPS PSEL & & & & & OUT Fig. 4: Block diagram of output power control circuitry There are two ways to select the desired output power step. First by applying a DC voltage at the pin PSEL, then this voltage directly selects the desired output power step. This kind of power selection can be used if the transmission power must be changed during operation. For a fixed-power application a resistor can be used which is connected from the PSEL pin to ground. The voltage drop across this resistor selects the desired output power level. For fixed-power applications at the highest power step this resistor can be omitted. The pin PSEL is in a high impedance state during the “TX standby” mode. 2.6 Lock Detection The lock detection circuitry turns on the power amplifier only after PLL lock. This prevents from unwanted emission of the transmitter if the PLL is unlocked. 2.7 Low Voltage Detection The supply voltage is sensed by a low voltage detect circuitry. The power amplifier is turned off if the supply voltage drops below a value of about 1.85 V. This is done in order to prevent unwanted emission of the transmitter if the supply voltage is too low. 39012 7201301 Rev. 001 Page 5 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description 2.8 Mode Control Logic The mode control logic allows two different modes of operation as listed in the following table. The mode control pin ENTX is pulleddown internally. This guarantees that the whole circuit is shut down if this pin is left floating. ENTX Mode Description 0 TX standby TX disabled 1 TX active TX enable 2.9 Timing Diagrams After enabling the transmitter by the ENTX signal, the power amplifier remains inactive for the time ton, the transmitter start-up time. The crystal oscillator starts oscillation and the PLL locks to the desired output frequency within the time duration ton. After successful PLL lock, the LOCK signal turns on the power amplifier, and then the RF carrier can be FSK modulated. high high EN EN low low high high LOCK LOCK low low high high FSKDTA PSEL low low RF carrier t t t on t on Fig. 5: Timing diagram for FSK modulation For more detailed information, please refer to the latest MLX72013 data sheet revision. 39012 7201301 Rev. 001 Page 6 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description 3 50Ω Connector Board Circuit Diagram Fig. 7: Circuit diagram with 50 Ω matching network 3.1 Board Component Values to Fig. 7 Part Size Value @ 433.92 MHz Tolerance CM1 0805 8.2 pF ±5% impedance matching capacitor CM2 0805 12 pF ±5% impedance matching capacitor CM3 0805 82 pF ±5% impedance matching capacitor LM 0805 22 nH ±5% impedance matching inductor, note 2 LT 0805 27 nH ±5% output tank inductor, note 2 CX1 0805 10 pF ±5% XOSC capacitor (Δf = ±20 kHz) , note 1 CX2 0805 12 pF 0805 1 nF ±5% ±5% XOSC capacitor (Δf = ±20 kHz) , note 1 CK RPS 0805 NIP ±5% power-select resistor R1 0805 0Ω ±5% ASK modulation connection CB0 0805 220 nF ±20% de-coupling capacitor CB1 0805 330 pF ±10% de-coupling capacitor Y/ SMD XTAL 6x3.5 27.12000 MHz ±30ppm calibr. ±20ppm temp. Description reference oscillator input coupling capacitor fundamental wave crystal (C3M2712000E10FSDHK01), CL = 10 pF, C0 = 3 pF, R1 = 50 Ω Note 1: depends on crystal parameters, other ∆f values can be selected with other CX1, CX2 values Note 2: for high-power applications high-Q wire-wound inductors should be used • NIP – not in place, may be used optionally 39012 7201301 Rev. 001 Page 7 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description 3.2 50Ω Connector Board PCB Top View Board size is 22 mm x 43 mm 3.3 Board Connection VCC Power supply (1.9 V to 5.5 V) ROI FSKD Input for FSK data (CMOS, see para. 2.2) PSEL Input for ASK data (R1 connect) 39012 7201301 Rev. 001 ENTX External reference frequency input Mode control pin Several ground pins Page 8 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description 4 Evaluation Board Layouts Board layout data in Gerber format are available, board size is 22mm x 43mm x 1mm FR4. PCB top view PCB bottom view 5 Board Variants Type EVB72013 Frequency/MHz Modulation –315 –FSK –433 –ASK –868 –FM according to section 3.1 Board Execution –A antenna version –C connector version –915 Note: 39012 7201301 Rev. 001 available EVB setups Page 9 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description 6 Package Description • The device MLX72013 is RoHS compliant. D e 7° ZD E H 8 DETAIL - A 1 L B DETAIL - A C A1 A A2 0.38 x 45° BSC (0.015x45°) .10 (.004) Fig. 10: SOIC8 all Dimension in mm, coplanarity < 0.1mm D E H A A1 min 4.80 max 4.98 A2 3.81 5.80 1.52 0.10 1.37 3.99 6.20 1.72 0.25 1.57 e 1.27 B 0.36 0.46 ZD 0.53 C L α 0.19 0.41 0° 0.25 1.27 8° 0.075 0.016 0° 0.098 0.050 8° all Dimension in inch, coplanarity < 0.004” min 0.189 0.150 0.2284 0.060 0.0040 0.054 max 0.196 0.157 0.2440 0.068 0.0098 0.062 0.050 0.014 0.018 0.021 6.1 Soldering Information • The device MLX72013 is qualified for MSL1 with soldering peak temperature 260 deg C according to JEDEC J-STD-20. 39012 7201301 Rev. 001 Page 10 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description Your Notes 39012 7201301 Rev. 001 Page 11 of 12 EVB Description Jan/09 EVB72013 433MHz Transmitter Evaluation Board Description 7 Disclaimer 1) The information included in this documentation is subject to Melexis intellectual and other property rights. Reproduction of information is permissible only if the information will not be altered and is accompanied by all associated conditions, limitations and notices. 2) Any use of the documentation without the prior written consent of Melexis other than the one set forth in clause 1 is an unfair and deceptive business practice. Melexis is not responsible or liable for such altered documentation. 3) The information furnished by Melexis in this documentation is provided ’as is’. Except as expressly warranted in any other applicable license agreement, Melexis disclaims all warranties either express, implied, statutory or otherwise including but not limited to the merchantability, fitness for a particular purpose, title and non-infringement with regard to the content of this documentation. 4) Notwithstanding the fact that Melexis endeavors to take care of the concept and content of this documentation, it may include technical or factual inaccuracies or typographical errors. Melexis disclaims any responsibility in connection herewith. 5) Melexis reserves the right to change the documentation, the specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with Melexis for current information. 6) Melexis shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the information in this documentation. 7) The product described in this documentation is intended for use in normal commercial applications. Applications requiring operation beyond ranges specified in this documentation, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by Melexis for each application. 8) Any supply of products by Melexis will be governed by the Melexis Terms of Sale, published on www.melexis.com. © Melexis NV. All rights reserved. For the latest version of this document, go to our website at: www.melexis.com Or for additional information contact Melexis Direct: Europe, Asia: Americas: Asia: Phone: +32 1367 0495 Phone: +1 603 223 2362 Phone: +32 1367 0495 E-mail: [email protected] E-mail: [email protected] E-mail: [email protected] ISO/TS 16949 and ISO14001 Certified 39012 7201301 Rev. 001 Page 12 of 12 EVB Description Jan/09