lm2936q q1

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
Reference
Design
LM2936Q
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
LM2936Q Ultralow Quiescent Current LDO Voltage Regulator
1 Features
3 Description
•
•
The LM2936Q ultralow quiescent-current regulator
features low dropout voltage and low current in the
standby mode. With less than 15-μA quiescent
current at a 100-μA load, the LM2936Q is ideally
suited for automotive and other battery-operated
systems. The LM2936Q retains all of the features that
are common to low-dropout regulators including a low
dropout PNP pass device, short-circuit protection,
reverse battery protection, and thermal shutdown.
The LM2936Q has a 40-V maximum operating
voltage limit, a −40°C to +125°C operating
temperature range, and ±3% output voltage tolerance
over the entire output current, input voltage, and
temperature range. The LM2936Q is available in
8-pin SOIC and VSSOP packages, a 4-pin SOT–223
package, as well as a 3-pin TO-252 surface mount
package.
1
•
•
•
•
•
•
•
•
•
•
•
•
Qualified for Automotive Applications
AEC Q100-Qualified With the Following Results
– Device Temperature Grade 1: –40°C to
+125°C Ambient Operating Temperature
Range
Operating Input Voltage: 5.5 V to 40 V
Ultralow Quiescent Current (IQ ≤ 15 μA for
IOUT = 100 μA)
Fixed 3-V, 3.3-V or 5-V With 50-mA Output
±2% Initial Output Tolerance
±3% Output Tolerance Over Line, Load, and
Temperature
Dropout Voltage Typically 200 mV at IOUT = 50 mA
Reverse Battery Protection
–50-V Input Transient Protection
Internal Short Circuit Current Limit
Internal Thermal Shutdown Protection
40-V Operating Voltage Limit
Shutdown Pin Available with LM2936QBM
Package
Device Information(1)
PART NUMBER
LM2936Q
PACKAGE
BODY SIZE (NOM)
SOIC (8)
4.90 mm × 3.91 mm
TO-252 (3)
6.10 mm × 6.58 mm
VSSOP (8)
3.00 mm × 3.00 mm
SOT-223 (4)
6.50 mm × 3.50 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
2 Applications
Automotive
Simplified Schematic
IN
VIN
OUT
VOUT
GND
CIN
100 nF *
COUT
10 µF **
Copyright © 2016, Texas Instruments Incorporated
* Required if regulator is located more than 2 inches from power supply filter capacitor.
** Required for stability. See Electrical Characteristics for 3-V LM2936Q for required values. Must be rated over
intended operating temperature range. Effective equivalent series resistance (ESR) is critical, see Typical
Characteristics. Locate capacitor as close to the regulator output and ground pins as possible. Capacitance may be
increased without bound.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM2936Q
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
4
4
4
4
5
6
7
8
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics for 3-V LM2936Q ..............
Electrical Characteristics for 3.3-V LM2936Q ...........
Electrical Characteristics for 5-V LM2936Q ..............
Typical Characteristics ..............................................
Detailed Description ............................................ 12
7.1 Overview ................................................................. 12
7.2 Functional Block Diagram ....................................... 12
7.3 Feature Description................................................. 12
7.4 Device Functional Modes........................................ 13
8
Application and Implementation ........................ 14
8.1 Application Information............................................ 14
8.2 Typical Application ................................................. 14
9 Power Supply Recommendations...................... 16
10 Layout................................................................... 17
10.1 Layout Guidelines ................................................. 17
10.2 Layout Examples................................................... 17
11 Device and Documentation Support ................. 18
11.1
11.2
11.3
11.4
11.5
Documentation Support ........................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
18
18
18
18
18
12 Mechanical, Packaging, and Orderable
Information ........................................................... 18
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (March 2013) to Revision D
Page
•
Added Pin Configuration and Functions section, ESD Rating table, Thermal Information table with updated values,
Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply
Recommendations section, Layout section, Device and Documentation Support section, and Mechanical,
Packaging, and Orderable Information section ..................................................................................................................... 1
•
Changed θJA for SOIC from 140°C/W to 111.4°C/W; for TO-252 from 136°C/W to 50.5°C/W; for VSSOP from
200°C/W to 173.4°C/W; and for SOT-223 from149°C/W to 62.8°C/W .................................................................................. 4
•
Changed θJC for SOIC from 45°C/W to 56.3°C/W (top); TO-252 from 6°C/W to 52.6°C/W (top) and 1.6°C/W
(bottom); SOT-223 from 36°C/W to 44.2°C/W (top) .............................................................................................................. 4
Changes from Revision B (May 2012) to Revision C
•
2
Page
Changed layout of National Data Sheet to TI format ............................................................................................................. 1
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
LM2936Q
www.ti.com
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
5 Pin Configuration and Functions
NDP Package
3-Pin TO-252
Top View
OUT 3
IN 1
4 GND
(TAB)
GND 2
OUT 3
D Package (LM2936QHBM)
8-Pin SOIC
Top View
GND 3
NC 4
4 GND
(TAB)
D Package (LM2936QM)
8-Pin SOIC
Top View
8 IN
OUT 1
7 GND
GND 2
6 GND
GND 3
8 IN
LM2936M
GND 2
LM2936BM
OUT 1
LM2936MP
LM2936DT
IN 1
DCY Package
4-Pin SOT-223
Top View
NC 4
5 SD
7 GND
6 GND
5 NC
DGK Package
8-Pin VSSOP
Top View
8 IN
LM2936MM
OUT 1
NC 2
NC 3
NC 4
7 GND
6 NC
5 NC
Pin Functions
PIN
NAME
IN
D
(LM2936QHBM
A)
D
(LM2936QM)
NDP
DGK
DCY
I/O
DESCRIPTION
8
8
1
8
1
I
GND
2, 3, 6, 7
2, 3, 6, 7
4
7
2, 4
—
Ground.
OUT
1
1
3
1
3
O
Regulated output voltage. Requires a minimum output
capacitance, with specific ESR, on this pin to maintain
stability.
Shutdown (LM2936QHBMA only). Pull this pin HIGH (>
2 V) to turn the output OFF. If this pin is left open, pull
ed low (< 0.6 V), or connected to GND, the output will
be ON by default. Avoid having any voltage from 0.6 V
to 2 V on this pin as the output status may not be
predicable across the operating range.
SD
5
—
—
—
—
I
NC
4
4, 5
—
2, 3, 4, 5, 6
—
—
Unregulated input voltage.
No internal connection, Connect to GND, or leave
open.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
3
LM2936Q
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN
MAX
UNIT
−50
60
V
Input voltage (survival)
Power dissipation
(3)
Internally limited
Junction temperature, TJMAX
150
−65
Storage temperature, Tstg
(1)
(2)
(3)
°C
150
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If Military/Aerospace specified devices are required, contact the TI Sales Office/ Distributors for availability and specifications.
The maximum power dissipation is a function of TJ(MAX), RθJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(MAX) − TA) / RθJA. If this dissipation is exceeded, the die temperature can rise above the TJ(MAX) of 150°C, and
the LM2936Q may go into thermal shutdown.
6.2 ESD Ratings
V(ESD)
(1)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
VALUE
UNIT
±2000
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. .
6.3 Recommended Operating Conditions
MIN
MAX
UNIT
−40
125
°C
Input voltage, VIN (LM2936Q)
5.5
40
V
Input voltage, VIN (LM2936QH only)
5.5
60
V
0
40
V
Temperature, TJ
Shutdown pin voltage, VSD (LM2936QHBMA only)
6.4 Thermal Information
LM2936Q
THERMAL METRIC
(1)
SOIC
(D)
TO-252
(NDP)
VSSOP
(DGK)
SOT-223
(DCY)
UNIT
8 PINS
3 PINS
8 PINS
4 PINS
RθJA (2)
Junction-to-ambient thermal resistance, High-K
111.4
50.5
173.4
62.8
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
56.3
52.6
65.9
44.2
°C/W
RθJB
Junction-to-board thermal resistance
51.9
29.7
94.9
11.7
°C/W
ψJT
Junction-to-top characterization parameter
10.9
4.8
9.6
3.6
°C/W
ψJB
Junction-to-board characterization parameter
51.4
29.3
93.3
11.6
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
n/a
1.6
n/a
n/a
°C/W
(1)
(2)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Thermal resistance value RθJA is based on the EIA/JEDEC High-K printed circuit board defined by: JESD51-7 - High Effective Thermal
Conductivity Test Board for Leaded Surface Mount Packages.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
LM2936Q
www.ti.com
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
6.5 Electrical Characteristics for 3-V LM2936Q
VIN = 14 V, IOUT = 10 mA, TJ = 25°C, unless otherwise specified.
MIN (1)
TYP (2)
MAX (1)
2.94
3
3.06
2.91
3.000
3.09
IOUT = 100 μA, 8 V ≤ VIN ≤ 24 V
15
20
μA
IOUT = 10 mA, 8 V ≤ VIN ≤ 24 V
0.2
0.5
mA
IOUT = 50 mA, 8 V ≤ VIN ≤ 24 V
1.5
2.5
mA
5
10
6 V ≤ VIN ≤ 40 V, IOUT = 1 mA
10
30
100 μA ≤ IOUT ≤ 5 mA
10
30
5 mA ≤ IOUT ≤ 50 mA
10
30
0.05
0.1
0.20
0.40
V
120
250
mA
PARAMETER
Output voltage
Quiescent current
Line regulation
Load regulation
Dropout voltage
TEST CONDITIONS
4 V ≤ VIN ≤ 26 V, 100 µA ≤ IOUT ≤ 50 mA (2)
–40°C ≤ TJ ≤ 125°C
9 V ≤ VIN ≤ 16 V
IOUT = 100 μA
IOUT = 50 mA
65
UNIT
V
mV
mV
V
Short-circuit current
VOUT = 0 V
Output impedance
IOUT = 30 mAdc and 10 mArms, ƒ = 1000 Hz
450
Output noise voltage
10 Hz–100 kHz
500
μV
20
mV/1000 Hr
Long-term stability
mΩ
Ripple rejection
Vripple = 1 Vrms, ƒripple = 120 Hz
−40
−60
dB
Reverse polarity transient input
voltage
RL = 500 Ω, t = 1 ms
−50
−80
V
Output voltage with reverse
polarity input
VIN = −15 V, RL = 500 Ω
Maximum line transient
RL = 500 Ω, VOUT ≤ 3.3 V, T = 40 ms
60
Output bypass capacitance
(COUT) ESR
COUT = 22 µF, 0.1 mA ≤ IOUT ≤ 50 mA
0.3
(1)
(2)
0
−0.3
V
V
8
Ω
Datasheet minimum and max specification limits are ensured by design, test, or statistical analysis.
Typical limits are at 25°C (unless otherwise specified) and represent the most likely parametric norm.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
5
LM2936Q
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
www.ti.com
6.6 Electrical Characteristics for 3.3-V LM2936Q
VIN = 14 V, IOUT = 10 mA, TJ = 25°C, unless otherwise specified.
MIN (1)
TYP (2)
MAX (1)
3.234
3.300
3.366
3.201
3.300
3.399
IOUT = 100 μA, 8 V ≤ VIN ≤ 24 V
15
20
μA
IOUT = 10 mA, 8 V ≤ VIN ≤ 24 V
0.2
0.5
mA
IOUT = 50 mA, 8 V ≤ VIN ≤ 24 V
1.5
2.5
mA
5
10
6 V ≤ VIN ≤ 40 V, IOUT = 1 mA
10
30
100 μA ≤ IOUT ≤ 5 mA
10
30
5 mA ≤ IOUT ≤ 50 mA
10
30
0.05
0.10
PARAMETER
Output voltage
Quiescent current
Line regulation
Load regulation
Dropout voltage
TEST CONDITIONS
4 V ≤ VIN ≤ 26 V, 100 µA ≤ IOUT ≤ 50 mA (3)
–40°C ≤ TJ ≤ 125°C
9 V ≤ VIN ≤ 16 V
IOUT = 100 μA
IOUT = 50 mA
65
UNIT
V
mV
mV
V
0.2
0.4
V
120
250
mA
Short-circuit current
VOUT = 0 V
Output impedance
IOUT = 30 mAdc and 10 mArms, ƒ = 1000 Hz
450
Output noise voltage
10 Hz–100 kHz
500
μV
20
mV/1000 Hr
Long-term stability
mΩ
Ripple rejection
Vripple = 1 Vrms, ƒripple = 120 Hz
−40
−60
dB
Reverse polarity transient input
voltage
RL = 500 Ω, T = 1 ms
−50
−80
V
Output voltage with reverse polarity
VIN = −15 V, RL = 500 Ω
input
0
Maximum line transient
RL = 500 Ω, VOUT ≤ 3.63 V, T = 40 ms
60
Output bypass capacitance
(COUT) ESR
COUT = 22 µF, 0.1 mA ≤ IOUT ≤ 50 mA
0.3
(1)
(2)
(3)
6
−0.3
V
V
8
Ω
Datasheet minimum and maximum specification limits are ensured by design, test, or statistical analysis.
Typical limits are at 25°C (unless otherwise specified) and represent the most likely parametric norm.
To ensure constant junction temperature, pulse testing is used.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
LM2936Q
www.ti.com
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
6.7 Electrical Characteristics for 5-V LM2936Q
VIN = 14 V, IOUT = 10 mA, TJ = 25°C, unless otherwise specified.
PARAMETER
TEST CONDITIONS
MIN (1)
TYP (2)
MAX (1)
4.85
5
5.15
15
35
4.9
5
5.1
4.85
5
5.15
UNIT
5-V LM2936QHBMA ONLY
Output voltage
5.5 V ≤ VIN ≤ 48 V, 100 µA ≤ IOUT ≤ 50 mA (3)
–40°C ≤ TJ ≤ 125°C
Line regulation
6 V ≤ VIN ≤ 60 V, IOUT = 1 mA
V
mV
ALL 5-V LM2936Q
Output voltage
Quiescent current
Line regulation
Load regulation
Dropout voltage
5.5 V ≤ VIN ≤ 26 V, 100 µA ≤ IOUT ≤ 50 mA (3)
–40°C ≤ TJ ≤ 125°C
V
IOUT = 100 μA, 8 V ≤ VIN ≤ 24 V
9
15
μA
IOUT = 10 mA, 8 V ≤ VIN ≤ 24 V
0.2
0.5
mA
IOUT = 50 mA, 8 V ≤ VIN ≤ 24 V
1.5
2.5
mA
9 V ≤ VIN ≤ 16 V
5
10
6 V ≤ VIN ≤ 40 V, IOUT = 1 mA
10
30
100 μA ≤ IOUT ≤ 5 mA
10
30
5 mA ≤ IOUT ≤ 50 mA
10
30
IOUT = 100 μA
0.05
0.1
V
IOUT = 50 mA
0.2
0.4
V
120
250
65
mV
mV
Short-circuit current
VOUT = 0 V
Output impedance
IOUT = 30 mAdc and 10 mArms, ƒ = 1000 Hz
450
Output noise voltage
10 Hz–100 kHz
500
μV
20
mV/1000 Hr
Long-term stability
mA
mΩ
Ripple rejection
Vripple = 1 Vrms, ƒripple = 120 Hz
−40
−60
dB
Reverse polarity transient input voltage
RL = 500 Ω, T = 1 ms
−50
−80
V
Output voltage with reverse polarity
input
VIN = −15 V, RL = 500 Ω
Maximum line transient
RL = 500 Ω, VOUT ≤ 5.5 V, T = 40 ms
60
Output bypass capacitance (COUT)
ESR
COUT = 10 µF, 0.1 mA ≤ IOUT ≤ 50 mA
0.3
0
−0.3
V
V
8
Ω
0.01
V
SHUTDOWN INPUT: 5-V LM2936QHBMA ONLY
Output voltage, VOUT
Output off, VSD = 2.4 V, RLOAD = 500 Ω
Shutdown high threshold voltage, VIH
Output off, RLOAD = 500 Ω
Shutdown low
threshold voltage, VIL
Output on, RLOAD = 500 Ω
Shutdown high
current, IIH
Output off, VSD = 2.4 V, RLOAD = 500 Ω
Quiescent current
Output off, VSD = 2.4 V, RLOAD = 500Ω,
includes IIH current
(1)
(2)
(3)
0
2
1.1
1.1
V
0.6
V
12
μA
30
μA
Datasheet minimum and maximum specification limits are ensured by design, test, or statistical analysis.
Typical limits are at 25°C (unless otherwise specified) and represent the most likely parametric norm.
To ensure constant junction temperature, pulse testing is used.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
7
LM2936Q
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
www.ti.com
6.8 Typical Characteristics
8
Figure 1. Dropout Voltage
Figure 2. Dropout Voltage
Figure 3. Quiescent Current
Figure 4. Quiescent Current
Figure 5. Quiescent Current
Figure 6. Quiescent Current
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
LM2936Q
www.ti.com
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
Typical Characteristics (continued)
Figure 8. 3-V LM2936Q COUT ESR
Figure 7. Quiescent Current
50
Figure 9. 3.3-V LM2936Q COUT ESR
Figure 10. 5-V LM2936Q COUT ESR
Figure 11. Peak Output Current
Figure 12. Peak Output Current
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
9
LM2936Q
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
www.ti.com
Typical Characteristics (continued)
10
Figure 13. 5-V LM2936Q Current Limit
Figure 14. 5-V LM2936Q Line Transient Response
Figure 15. 5-V LM2936Q Output at Voltage Extremes
Figure 16. 5-V LM2936Q Ripple Rejection
Figure 17. 5-V LM2936Q Load Transient Response
Figure 18. 5-V LM2936Q Low Voltage Behavior
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
LM2936Q
www.ti.com
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
Typical Characteristics (continued)
Figure 19. 5-V LM2936Q Output Impedance
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
11
LM2936Q
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
www.ti.com
7 Detailed Description
7.1 Overview
The LM2936Q ultralow quiescent current regulator is ideally suited for automotive and other battery operated
systems, with less than 15 μA quiescent current at a 100-μA load. The device features low dropout voltage and
low current in the standby mode and retains all of the features that are common to low dropout regulators
including a low dropout PNP pass device, short circuit protection, reverse battery input protection, and thermal
shutdown. The LM2936Q has a 40-V maximum operating voltage limit and ±3% output voltage tolerance over the
entire output current, input voltage, and temperature range.
7.2 Functional Block Diagram
IN
OUT
Current
Limit
Thermal
Shutdown
PNP
+
Bandgap
Reference
LM2936
GND
Copyright © 2016, Texas Instruments Incorporated
7.3 Feature Description
7.3.1 High Input Operating Voltage
Unlike many other PNP low dropout regulators, the LM2936Q remains fully operational with VIN = 40 V, and the
LM2936QHBM remains fully operational with VIN = 60 V. Owing to power dissipation characteristics of the
available packages, full output current cannot be ensured for all combinations of ambient temperature and input
voltage.
While the LM2936QHBM maintains regulation to 60 V, it does not withstand a short circuit to ground on the
output when VIN is above 40 V because of safe operating area limitations in the internal PNP pass device. Above
60 V the LM2936Q breaks down with catastrophic effects on the regulator and possibly the load as well. Do not
use this device in a design where the input operating voltage may exceed 40 V, or where transients are likely to
exceed 60 V.
7.3.2 Thermal Shutdown (TSD)
The TSD circuitry of the LM2936Q has been designed to protect the device against temporary thermal overload
conditions. The TSD circuitry is not intended to replace proper heat-sinking. Continuously running the LM2936Q
device at TSD may degrade device reliability as the junction temperature will be exceeding the absolute maximum
junction temperature rating. If the LM2936Q goes into TSD mode, the output current shuts off until the junction
temperature falls approximately 10°C — the output current is then automatically restored. The LM2936Q
continuously cycles in and out of TSD until the condition is corrected. The LM2936Q TSD junction temperature is
typically 160°C.
12
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
LM2936Q
www.ti.com
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
Feature Description (continued)
7.3.3 Short-Circuit Current Limit
The output current limiting circuitry of the LM2936Q has been designed to limit the output current in cases where
the load impedance is unusually low. This includes situations where the output may be shorted directly to ground.
Continuous operation of the LM2936Q at the current limit typically results in the LM2936Q transitioning into TSD
mode.
7.3.4 Shutdown (SD) Pin
The 5-V LM2936QHBMA has a pin for shutting down the regulator output. Applying a logic level high (> 2 V) to
the SD pin causes the output to turn off. Leaving the SD pin open, connecting it to ground, or applying a logic
level low (< 0.6 V) allows the regulator output to turn on.
7.4 Device Functional Modes
The LM2936Q design does not include any undervoltage lockout (UVLO), or overvoltage shutdown (OVSD)
functions. Generally, the output voltage tracks the input voltage until the input voltage is greater than VOUT + 1 V.
When the input voltage is greater than VOUT + 1 V the LM2936Q is in linear operation, and the output voltage is
regulated; however, the device is sensitive to any small perturbation of the input voltage. Device dynamic
performance is improved when the input voltage is at least 2 V greater than the output voltage.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
13
LM2936Q
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM2936Q ultralow quiescent current regulator features low dropout voltage and low current in the standby
mode. The LM2936Q has a 40-V maximum operating voltage limit, a −40°C to +125°C operating temperature
range, –24-V input transient protection, and ±3% output voltage tolerance over the entire output current, input
voltage, and temperature range The WEBENCH® software may be used to generate complete designs. When
generating a design, WEBENCH utilizes iterative design procedure and accesses comprehensive databases of
components. See www.ti.com for more details.
8.2 Typical Application
Figure 20 shows the typical application circuit for the LM2936Q. For the LM2936Q 5-V option, the output
capacitor, COUT, must have a capacitance value of at least 10 µF with an equivalent series resistance (ESR) of at
least 0.3 Ω, but no more than 8 Ω. For the LM2936Q 3-V and 3.3-V options, the output capacitor, COUT, must
have a capacitance value of at least 22 µF with an ESR of at least 0.3 Ω, but no more than 8 Ω. The minimum
capacitance value and the ESR requirements apply across the entire expected operating ambient temperature
range.
IN
VIN
OUT
VOUT
GND
CIN
100 nF *
COUT
10 µF **
Copyright © 2016, Texas Instruments Incorporated
* CIN is required only if the regulator is located more than 3 inches from the power-supply-filter capacitors.
** Required for stability. COUT must be at least 10 µF for the LM2936Q 5-V option, and at least 22 µF for the 3-V and
3.3-V options. Capacitance must be maintained over entire expected operating temperature range, and located as
close as possible to the regulator. The ESR, of the COUT capacitor must at least 0.3 Ω, but no more than 8 Ω.
Figure 20. LM2936Q Typical Application
8.2.1 Design Requirements
Table 1. Design Parameters
14
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage
5.5 V to 40 V
Output voltage
5V
Output current requirement
1 mA to 50 mA
Input capacitor
0.1 µF
Output capacitance
10 µF minimum
Output capacitor ESR value
0.3 Ω to 8 Ω
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
LM2936Q
www.ti.com
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
8.2.2 Detailed Design Procedure
8.2.2.1 External Capacitors
The output capacitor is critical to maintaining regulator stability, and must meet the required conditions for both
ESR and minimum amount of capacitance.
8.2.2.1.1 Minimum Capacitance
The minimum output capacitance required to maintain stability is at least 10 µF for the LM2936Q 5-V option, and
at least 22 µF for the 3-V and 3.3-V options. This value may be increased without limit. Larger values of output
capacitance will give improved transient response.
8.2.2.1.2 ESR Limits
The ESR of the output capacitor causes loop instability if it is too high, or too low. The ESR of the COUT capacitor
must at least 0.3 Ω, but no more than 8 Ω.
8.2.2.2 Output Capacitor ESR
It is essential that the output capacitor meet the capacitance and ESR requirements, or oscillations can result.
The ESR is used with the output capacitance in order to produce a zero in the control loop frequency response.
This zero increases phase margin and ensures stability of the output voltage. Refer to ESR, Stability, and the
LDO Regulator (SLVA115) for details.
Ceramic capacitors (MLCC) can be used for COUT only if a series resistor is added to simulate the ESR
requirement. The ESR is not optional — it is mandatory. Typically, a 500-mΩ to 1-Ω series resistor is used for
this purpose. When using MLCCs, due diligence must be given to initial tolerances, capacitance derating due to
applied DC voltage, and capacitance variations due to temperature. Dielectric types X5R and X7R are preferred.
8.2.2.3 Power Dissipation
Knowing the device power dissipation and proper sizing of the thermal plane connected to the tab or pad is
critical to ensuring reliable operation. Device power dissipation depends on input voltage, output voltage, and
load conditions and can be calculated with Equation 1.
PD(MAX) = (VIN(MAX) – VOUT) × IOUT
(1)
Power dissipation can be minimized, and greater efficiency can be achieved, by using the lowest available
voltage drop option that would still be greater than the dropout voltage (VDO). However, keep in mind that higher
voltage drops result in better dynamic (that is, PSRR and transient) performance.
On the 8-pin SOIC (D) package, the four ground pins are thermally connected to the backside of the die. Adding
approximately 0.04 square inches of 2 oz. copper pad area to these four pins improves the JEDEC RθJA rating
from 111.4°C/W to approximately 100°C/W. If this extra copper area is placed directly beneath the SOIC
package there should not be any impact on board density.
Power dissipation and junction temperature are most often related by the junction-to-ambient thermal resistance
(RθJA) of the combined PCB and device package and the temperature of the ambient air (TA), according to
Equation 2 or Equation 2:
TJ(MAX) = TA(MAX) + ( RθJA × PD(MAX))
PD = TJ(MAX) – TA(MAX) / RθJA
(2)
(3)
Unfortunately, this RθJA is highly dependent on the heat-spreading capability of the particular PCB design, and
therefore varies according to the total copper area, copper weight, and location of the planes. The RθJA recorded
in Thermal Information is determined by the specific EIA/JEDEC JESD51-7 standard for PCB and copperspreading area, and is to be used only as a relative measure of package thermal performance. For a welldesigned thermal layout, RθJA is actually the sum of the package junction-to-case (bottom) thermal resistance
(RθJCbot) plus the thermal resistance contribution by the PCB copper area acting as a heat sink.
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
15
LM2936Q
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
www.ti.com
8.2.2.4 Estimating Junction Temperature
The EIA/JEDEC standard recommends the use of psi (Ψ) thermal characteristics to estimate the junction
temperatures of surface mount devices on a typical PCB board application. These characteristics are not true
thermal resistance values, but rather package specific thermal characteristics that offer practical and relative
means of estimating junction temperatures. These psi metrics are determined to be significantly independent of
copper-spreading area. The key thermal characteristics (ΨJT and ΨJB) are given in Thermal Information and are
used in accordance with Equation 4 or Equation 5.
TJ(MAX) = TTOP + (ΨJT × PD(MAX))
where
•
•
PD(MAX) is explained in Equation 3
TTOP is the temperature measured at the center-top of the device package.
TJ(MAX) = TBOARD + (ΨJB × PD(MAX))
(4)
where
•
•
PD(MAX) is explained in Equation 3.
TBOARD is the PCB surface temperature measured 1-mm from the device package and centered on the
package edge.
(5)
For more information about the thermal characteristics ΨJT and ΨJB, see Semiconductor and IC Package
Thermal Metrics (SPRA953); for more information about measuring TTOP and TBOARD, see Using New Thermal
Metrics (SBVA025); and for more information about the EIA/JEDEC JESD51 PCB used for validating RθJA, see
Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs (SZZA017). These
application notes are available at www.ti.com.
8.2.3 Application Curve
Figure 21. LM2936Q VOUT vs VIN
9 Power Supply Recommendations
This device is designed to operate from an input supply voltage from at least VOUT + 1 V up to a maximum of 40
V. The input supply should be well regulated and free of spurious noise. To ensure that the LM2936Q output
voltage is well regulated the input supply must be at least VOUT + 2 V. A capacitor at the IN pin may not be
specifically required if the bulk input supply filter capacitors are within three inches of the IN pin, but adding one
is not detrimental to operation.
While the LM2936Q maintains regulation to VIN = 60 V, it cannot withstand a short circuit on the output with VIN
above 40 V because of safe operating area limitations in the internal PNP pass device. With VIN above 60 V the
LM2936Q breaks down with catastrophic effects on the regulator and possibly the load as well. Do not use this
device in a design where the input operating voltage, including transients, is likely to exceed 60 V.
16
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
LM2936Q
www.ti.com
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
10 Layout
10.1 Layout Guidelines
The dynamic performance of the LM2936Q is dependent on the layout of the PCB. PCB layout practices that are
adequate for typical LDOs may degrade the PSRR, noise, or transient performance of the LM2936Q. Best
performance is achieved by placing CIN and COUT on the same side of the PCB as the LM2936Q, and as close to
the packageas is practical. The ground connections for CIN and COUT must be back to the LM2936Q ground pin
using as wide and as short of a copper trace as possible.
Connections using long trace lengths, narrow trace widths, and/or connections through vias must be avoided as
these add parasitic inductances and resistances that give inferior performance, especially during transient
conditions.
10.2 Layout Examples
6
3
7
2
8
1
VIN
5
GND
CIN
4
VSD
COUT
GND
VOUT
Figure 22. LM2936QHBM SOIC (D) Layout
5
6
3
7
2
8
1
VIN
4
GND
GND
VOUT
Figure 23. LM2936QM SOIC (D) Layout
Thermal
Vias
4
GND
CIN
GND
1
3
COUT
VIN
VOUT
Figure 24. LM2936Q TO-252 (NDP) Layout
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
17
LM2936Q
SNVS684D – NOVEMBER 2010 – REVISED MARCH 2016
www.ti.com
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation see the following:
• Semiconductor and IC Package Thermal Metrics (SPRA953)
• ESR, Stability, and the LDO Regulator (SLVA115)
• Semiconductor and IC Package Thermal Metrics (SPRA953)
• Using New Thermal Metrics (SBVA025)
• Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs (SZZA017)
11.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.3 Trademarks
E2E is a trademark of Texas Instruments.
WEBENCH is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
18
Submit Documentation Feedback
Copyright © 2010–2016, Texas Instruments Incorporated
Product Folder Links: LM2936Q
PACKAGE OPTION ADDENDUM
www.ti.com
19-Feb-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2936QDT-3.0/NOPB
ACTIVE
TO-252
NDP
3
75
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 125
LM2936Q
DT-3.0
LM2936QDT-3.3/NOPB
ACTIVE
TO-252
NDP
3
75
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 125
LM2936Q
DT-3.3
LM2936QDT-5.0/NOPB
ACTIVE
TO-252
NDP
3
75
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 125
LM2936Q
DT-5.0
LM2936QDTX-3.0/NOPB
ACTIVE
TO-252
NDP
3
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 125
LM2936Q
DT-3.0
LM2936QDTX-3.3/NOPB
ACTIVE
TO-252
NDP
3
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 125
LM2936Q
DT-3.3
LM2936QDTX-5.0/NOPB
ACTIVE
TO-252
NDP
3
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 125
LM2936Q
DT-5.0
LM2936QHBMA-5.0/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
2936H
QBM5.0
LM2936QHBMAX5.0/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
2936H
QBM5.0
LM2936QM-3.3/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM293
6Q-3.3
LM2936QM-5.0/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM293
6QM-5
LM2936QMM-3.0/NOPB
ACTIVE
VSSOP
DGK
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
KBCQ
LM2936QMM-3.3/NOPB
ACTIVE
VSSOP
DGK
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
KBBQ
LM2936QMM-5.0/NOPB
ACTIVE
VSSOP
DGK
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
KBAQ
LM2936QMMX-3.3/NOPB
ACTIVE
VSSOP
DGK
8
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
KBBQ
LM2936QMMX-5.0/NOPB
ACTIVE
VSSOP
DGK
8
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
KBAQ
LM2936QMP-3.0/NOPB
ACTIVE
SOT-223
DCY
4
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
KACQ
LM2936QMP-3.3/NOPB
ACTIVE
SOT-223
DCY
4
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
KABQ
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
19-Feb-2016
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2936QMP-5.0/NOPB
ACTIVE
SOT-223
DCY
4
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
KAAQ
LM2936QMPX-3.0/NOPB
ACTIVE
SOT-223
DCY
4
2000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
KACQ
LM2936QMPX-3.3/NOPB
ACTIVE
SOT-223
DCY
4
2000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
KABQ
LM2936QMPX-5.0/NOPB
ACTIVE
SOT-223
DCY
4
2000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2936QMX-3.3/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM293
6Q-3.3
LM2936QMX-5.0/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM293
6QM-5
KAAQ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
19-Feb-2016
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Feb-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM2936QDTX-3.0/NOPB
TO-252
NDP
3
2500
330.0
16.4
6.9
10.5
2.7
8.0
16.0
Q2
LM2936QDTX-3.3/NOPB
TO-252
NDP
3
2500
330.0
16.4
6.9
10.5
2.7
8.0
16.0
Q2
LM2936QDTX-5.0/NOPB
TO-252
NDP
3
2500
330.0
16.4
6.9
10.5
2.7
8.0
16.0
Q2
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM2936QMM-3.0/NOPB
VSSOP
DGK
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM2936QMM-3.3/NOPB
VSSOP
DGK
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM2936QMM-5.0/NOPB
VSSOP
DGK
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM2936QMMX-3.3/NOPB VSSOP
DGK
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM2936QMMX-5.0/NOPB VSSOP
DGK
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM2936QMP-3.0/NOPB SOT-223
DCY
4
1000
330.0
16.4
7.0
7.5
2.2
12.0
16.0
Q3
LM2936QMP-3.3/NOPB SOT-223
DCY
4
1000
330.0
16.4
7.0
7.5
2.2
12.0
16.0
Q3
LM2936QMP-5.0/NOPB SOT-223
DCY
4
1000
330.0
16.4
7.0
7.5
2.2
12.0
16.0
Q3
LM2936QMPX-3.0/NOPB SOT-223
DCY
4
2000
330.0
16.4
7.0
7.5
2.2
12.0
16.0
Q3
LM2936QMPX-3.3/NOPB SOT-223
DCY
4
2000
330.0
16.4
7.0
7.5
2.2
12.0
16.0
Q3
LM2936QMPX-5.0/NOPB SOT-223
DCY
4
2000
330.0
16.4
7.0
7.5
2.2
12.0
16.0
Q3
LM2936QHBMAX5.0/NOP
B
LM2936QMX-3.3/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM2936QMX-5.0/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Feb-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM2936QDTX-3.0/NOPB
TO-252
NDP
3
2500
367.0
367.0
38.0
LM2936QDTX-3.3/NOPB
TO-252
NDP
3
2500
367.0
367.0
38.0
LM2936QDTX-5.0/NOPB
TO-252
NDP
3
2500
367.0
367.0
38.0
SOIC
D
8
2500
367.0
367.0
35.0
LM2936QMM-3.0/NOPB
VSSOP
DGK
8
1000
210.0
185.0
35.0
LM2936QMM-3.3/NOPB
VSSOP
DGK
8
1000
210.0
185.0
35.0
LM2936QMM-5.0/NOPB
VSSOP
DGK
8
1000
210.0
185.0
35.0
LM2936QMMX-3.3/NOPB
VSSOP
DGK
8
3500
367.0
367.0
35.0
LM2936QMMX-5.0/NOPB
VSSOP
DGK
8
3500
367.0
367.0
35.0
LM2936QMP-3.0/NOPB
SOT-223
DCY
4
1000
367.0
367.0
35.0
LM2936QMP-3.3/NOPB
SOT-223
DCY
4
1000
367.0
367.0
35.0
LM2936QMP-5.0/NOPB
SOT-223
DCY
4
1000
367.0
367.0
35.0
LM2936QMPX-3.0/NOPB
SOT-223
DCY
4
2000
367.0
367.0
35.0
LM2936QMPX-3.3/NOPB
SOT-223
DCY
4
2000
367.0
367.0
35.0
LM2936QMPX-5.0/NOPB
SOT-223
DCY
4
2000
367.0
367.0
35.0
LM2936QMX-3.3/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
LM2936QMX-5.0/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
LM2936QHBMAX5.0/NOP
B
Pack Materials-Page 2
MECHANICAL DATA
NDP0003B
TD03B (Rev F)
www.ti.com
MECHANICAL DATA
MPDS094A – APRIL 2001 – REVISED JUNE 2002
DCY (R-PDSO-G4)
PLASTIC SMALL-OUTLINE
6,70 (0.264)
6,30 (0.248)
3,10 (0.122)
2,90 (0.114)
4
0,10 (0.004) M
3,70 (0.146)
3,30 (0.130)
7,30 (0.287)
6,70 (0.264)
Gauge Plane
1
2
0,84 (0.033)
0,66 (0.026)
2,30 (0.091)
4,60 (0.181)
1,80 (0.071) MAX
3
0°–10°
0,10 (0.004) M
0,25 (0.010)
0,75 (0.030) MIN
1,70 (0.067)
1,50 (0.059)
0,35 (0.014)
0,23 (0.009)
Seating Plane
0,08 (0.003)
0,10 (0.0040)
0,02 (0.0008)
4202506/B 06/2002
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters (inches).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion.
Falls within JEDEC TO-261 Variation AA.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated