Evaluation Module

Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
LM5175 42 V Wide VIN Synchronous 4-Switch Buck-Boost Controller
1 Features
3 Description
•
The LM5175 is a synchronous four-switch buck-boost
DC/DC controller capable of regulating the output
voltage at, above, or below the input voltage. The
LM5175 operates over a wide input voltage range of
3.5 V to 42 V (60 V maximum) to support a variety of
applications.
1
•
•
•
•
•
•
•
•
•
•
•
•
•
Single Inductor Buck-Boost Controller for StepUp/Step-Down DC/DC Conversion
Wide VIN Range: 3.5 V to 42 V, 60 V Maximum
Flexible VOUT Range: 0.8 V to 55 V
VOUT Short Protection
High Efficiency Buck-Boost Transition
Adjustable Switching Frequency
Optional Frequency Sync and Dithering
Integrated 2-A MOSFET Gate Drivers
Cycle-by-Cycle Current Limit and Optional Hiccup
Optional Input or Output Average Current Limiting
Programmable Input UVLO and Soft-Start
Power Good and Output Overvoltage Protection
Selectable CCM or DCM with Pulse Skipping
Available in HTSSOP-28 and QFN-28 Packages
The LM5175 employs current-mode control both in
buck and boost modes of operation for superior load
and line regulation. The switching frequency is
programmed by an external resistor and can be
synchronized to an external clock signal.
The device also features a programmable soft-start
function and offers protection features including
cycle-by-cycle current limiting, input undervoltage
lockout (UVLO), output overvoltage protection (OVP),
and thermal shutdown. In addition, the LM5175
features selectable Continuous Conduction Mode
(CCM) or Discontinuous Conduction Mode (DCM)
operation, optional average input or output current
limiting, optional spread spectrum to reduce peak
EMI, and optional hiccup mode protection in
sustained overload conditions.
2 Applications
•
•
•
•
•
Automotive Start-Stop Systems
Backup Battery and Supercapacitor Charging
Industrial PC Power Supplies
USB Power Delivery
LED Lighting
Device Information
ORDER NUMBER
PACKAGE
BODY SIZE
LM5175PWP
HTSSOP-28
9.7 mm x 4.4 mm
LM5175RHF
QFN-28
4.0 mm x 5.0 mm
4 Simplified Schematic
VIN
Power Good
ISNS(+)
VIN
ISNS(-)
EN/UVLO
VISNS
VCC
Enable
PGOOD
VOUT
BOOT1
HDRV1
SW1
SS
LDRV1
SLOPE
CS
LM5175
RT/SYNC
CSG
LDRV2
COMP
SW2
AGND
BOOT2
VCC
BIAS
HDRV2
FB
MODE
VCC
DITH
PGND
VOSNS
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Schematic.............................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
5
7.1
7.2
7.3
7.4
7.5
7.6
5
5
5
6
6
9
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description ............................................ 12
8.1 Overview ................................................................. 12
8.2 Functional Block Diagram ....................................... 13
8.3 Feature Description................................................. 13
8.4 Device Functional Modes........................................ 19
9
Application and Implementation ........................ 20
9.1 Application Information............................................ 20
9.2 Typical Application .................................................. 20
10 Power Supply Recommendations ..................... 27
11 Layout................................................................... 27
11.1 Layout Guidelines ................................................. 27
11.2 Layout Example .................................................... 28
12 Device and Documentation Support ................. 29
12.1
12.2
12.3
12.4
12.5
Documentation Support ........................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
29
29
29
29
29
13 Mechanical, Packaging, and Orderable
Information ........................................................... 29
5 Revision History
Changes from Original (October 2015) to Revision A
Page
•
Added QFN-28 Packages....................................................................................................................................................... 1
•
Added LM5175RHF information ............................................................................................................................................ 1
•
Added RHF package .............................................................................................................................................................. 3
•
Added QFN pins .................................................................................................................................................................... 4
•
Changed first plus to minus ................................................................................................................................................. 18
•
Changed all 1.22 V to 1.23 V .............................................................................................................................................. 19
•
Changed equation ............................................................................................................................................................... 23
•
Changed equation ............................................................................................................................................................... 25
•
Changed equation ............................................................................................................................................................... 25
2
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
6 Pin Configuration and Functions
HTSSOP-28
PWP Package
Top View
EN/UVLO
1
28
SW1
VIN
2
27
HDRV1
VISNS
3
26
BOOT1
MODE
4
25
LDRV1
DITH
5
24
BIAS
RT
6
23
VCC
SLOPE
7
22
PGND
SS
8
21
LDRV2
COMP
9
20
BOOT2
AGND
10
19
HDRV2
FB
11
18
SW2
VOSNS
12
17
PGOOD
ISNS(±)
13
16
CS
ISNS(+)
14
15
CSG
LM5175
HTSSOP-28
VISNS
VIN
EN/UVLO
SW1
HDRV1
BOOT1
28
27
26
25
24
23
QFN-28
RHF Package
Top View
MODE
1
22
LDRV1
DITH
2
21
BIAS
RT
3
20
VCC
SLOPE
4
19
PGND
LM5175
QFN-28
FB
8
15
SW2
14
HDRV2
PGOOD
16
13
7
CS
AGND
12
BOOT2
CSG
17
11
6
ISNS(+)
COMP
10
LDRV2
ISNS(±)
18
9
5
VOSNS
SS
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
3
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
Pin Functions
PIN
NAME
DESCRIPTION
HTSSOP
QFN
EN/UVLO
1
26
Enable pin. For EN/UVLO < 0.4 V, the LM5175 is in a low current shutdown mode. For 0.7 V <
EN/UVLO < 1.23 V, the controller operates in standby mode in which the VCC regulator is enabled but
the PWM controller is not switching. For EN/UVLO > 1.23 V, the PWM function is enabled, provided
VCC exceeds the VCC UV threshold.
VIN
2
27
The input supply pin to the IC. Connect VIN to a supply voltage between 3.5 V and 42 V.
VISNS
3
28
VIN sense input. Connect to the input capacitor.
MODE
4
1
Mode = GND, DCM, Hiccup Disabled
(Set RMODE resistor to GND = 0 Ω)
Mode = 1.00 V, DCM, Hiccup Enabled
(Set RMODE resistor to GND = 49.9 kΩ)
Mode = 1.85 V, CCM, Hiccup Enabled
(Set RMODE resistor to GND = 93.1 kΩ)
Mode = VCC, CCM, Hiccup Disabled
(Set RMODE resistor to VCC = 0 Ω)
DITH
5
2
A capacitor connected between the DITH pin and AGND is charged and discharged with a 10 uA
current source. As the voltage on the DITH pin ramps up and down the oscillator frequency is
modulated between –5% and +5% of the nominal frequency set by the RT resistor. Grounding the
DITH pin will disable the dithering feature. In the external Sync mode, the DITH pin voltage is ignored.
RT/SYNC
6
3
Switching frequency programming pin. An external resistor is connected to the RT/SYNC pin and
AGND to set the switching frequency. This pin can also be used to synchronize the PWM controller to
an external clock.
SLOPE
7
4
A capacitor connected between the SLOPE pin and AGND provides the slope compensation ramp for
stable current mode operation in both buck and boost mode.
SS
8
5
Soft-start programming pin. A capacitor between the SS pin and AGND pin programs soft-start time.
COMP
9
6
Output of the error amplifier. An external RC network connected between COMP and AGND
compensates the regulator feedback loop.
AGND
10
7
Analog ground of the IC.
FB
11
8
Feedback pin for output voltage regulation. Connect a resistor divider network from the output of the
converter to the FB pin.
VOSNS
12
9
VOUT sense input. Connect to the output capacitor.
ISNS(–)
ISNS(+)
13
14
10
11
Input or Output Current Sense Amplifier inputs. An optional current sense resistor connected between
ISNS(+) and ISNS(–) can be located either on the input side or on the output side of the converter. If
the sensed voltage across the ISNS(+) and ISNS(-) pins reaches 50 mV, a slow Constant Current (CC)
control loop becomes active and starts discharging the soft-start capacitor to regulated the drop across
ISNS(+) and ISNS(-) to 50 mV. Short ISNS(+) and ISNS(-) together to disable this feature.
CSG
15
12
The negative or ground input to the PWM current sense amplifier. Connect directly to the low-side
(ground) of the current sense resistor.
CS
16
13
The positive input to the PWM current sense amplifier.
PGOOD
17
14
Power Good open drain output. PGOOD is pulled low when FB is outside a 0.8 V ±10% regulation
window.
SW2
SW1
18
28
15
25
The boost and the buck side switching nodes respectively.
HDRV2
HDRV1
19
27
16
24
Output of the high-side gate drivers. Connect directly to the gates of the high-side MOSFETs.
BOOT2
BOOT1
20
26
17
23
An external capacitor is required between the BOOT1, BOOT2 pins and the SW1, SW2 pins
respectively to provide bias to the high-side MOSFET gate drivers.
LDRV2
LDRV1
21
25
18
22
Output of the low-side gate drivers. Connect directly to the gates of the low-side MOSFETs.
PGND
22
19
Power ground of the IC. The high current ground connection to the low-side gate drivers.
VCC
23
20
Output of the VCC bias regulator. Connect capacitor to ground.
BIAS
24
21
Optional input to the VCC bias regulator. Powering VCC from an external supply instead of VIN can
reduce power loss at high VIN. For VBIAS > 8 V, the VCC regulator draws power from the BIAS pin. The
BIAS pin voltage must not exceed 40 V.
-
-
The PowerPAD should be soldered to the analog ground. If possible, use thermal vias to connect to a
PCB ground plane for improved power dissipation.
PowerPAD
™
4
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
7 Specifications
7.1 Absolute Maximum Ratings (1)
MIN
MAX
VIN, EN/UVLO, VISNS, VOSNS, ISNS(+), ISNS(–)
–0.3
60
BIAS
–0.3
40
FB, SS, DITH, RT/SYNC, SLOPE, COMP
–0.3
3.6
–1
60
SW1, SW2
SW1, SW2 (20 ns transient)
–3.0
65
VCC, MODE, PGOOD
–0.3
8.5
LDRV1, LDRV2
–0.3
8.5
BOOT1, HDRV1 with respect to SW1
–0.3
8.5
BOOT2, HDRV2 with respect to SW2
–0.3
8.5
BOOT1, BOOT2
–0.3
68
CS, CSG
–0.3
0.3
Operating junction temperature
–40
150
Storage temperature, Tstg
-65
150
(1)
UNIT
V
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 ESD Ratings
VALUE
VESD (1)
(1)
(2)
(3)
Human body model (HBM) ESD stress voltage (2)
±2000
Charged device model (CDM) ESD stress voltage (3)
±750
UNIT
V
Electrostatic discharge (ESD) to measure device sensitivity and immunity to damage caused by assembly line electrostatic discharges
into the device.
Level listed above is the passing level per ANSI/ESDA/JEDEC JS-001. JEDEC document JEP155 states that 500 V HBM allows safe
manufacturing with a standard ESD control process.
Level listed above is the passing level per EIA-JEDEC JESD22-C101. JEDEC document JEP157 states that 250 V CDM allows safe
manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) (1)
MIN
VIN
Input voltage range
BIAS
Bias supply voltage range
VOUT
EN/UVLO
ISNS(+), ISNS(-)
Average current sense common mode range
UNIT
8
36
Output voltage range
0.8
55
Enable voltage range
0
42
0
55
–40
125
°C
100
600
kHz
Operating temperature range
Fsw
Operating frequency range
(2)
MAX
42
TJ
(1)
NOM
3.5
(2)
V
Recommended Operating Conditions are conditions under the device is intended to be functional. For specifications and test conditions,
see Electrical Characteristics .
High junction temperatures degrade operating lifetimes. Operating lifetime is de-rated for junction temperatures greater than 125°C.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
5
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
7.4 Thermal Information
LM5175
THERMAL METRIC (1)
HTSSOP
QFN
28 PINS
28 PINS
RθJA
Junction-to-ambient thermal resistance
33.1
34.7
RθJC(top)
Junction-to-case (top) thermal resistance
17.7
26.6
RθJB
Junction-to-board thermal resistance
14.9
6.3
ψJT
Junction-to-top characterization parameter
0.4
0.3
ψJB
Junction-to-board characterization parameter
14.7
6.2
RθJC(bot)
Junction-to-case (bottom) thermal resistance
1.1
2.0
(1)
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
7.5 Electrical Characteristics
Typical values correspond to TJ = 25°C. Minimum and maximum limits apply over the –40°C to 125°C junction temperature
range unless otherwise stated. VIN = 24 V unless otherwise stated. (1)
PARAMETER
TEST CONDITION
MIN
TYP
MAX
UNIT
SUPPLY VOLTAGE (VIN)
VIN
Operating input voltage
IQ
VIN shutdown current
VEN/UVLO = 0 V
3.5
VIN standby current
VEN/UVLO = 1.1 V, non-switching
VIN operating current
VEN/UVLO = 2 V, VFB = 0.9 V
VVCC(VIN)
Regulation voltage
VBIAS = 0 V, VCC open
VUV(VCC)
VCC Undervoltage lockout
VCC increasing
42
V
1.4
10
µA
0.7
2
1.65
4
6.95
7.35
7.88
3.11
3.27
3.43
mA
VCC
Undervoltage hysteresis
160
V
mV
IVCC
VCC current limit
VVCC = 0 V
ROUT(VCC)
VCC regulator output impedance
IVCC = 30 mA, VIN = 3.5 V
65
mA
BIAS switchover voltage
VIN = 24 V
VEN(STBY)
Standby threshold
EN/UVLO rising
IEN(STBY)
Standby source current
VEN/UVLO = 1.1 V
VEN(OP)
Operating threshold
ΔIHYS(OP)
Operating hysteresis current
ISS
Soft-start pull up current
VSS = 0 V
VSS(CL)
SS clamp voltage
SS open
1.27
V
VFB - VSS
FB to SS offset
VSS = 0 V
-15
mV
9.3
16
Ω
7.25
8
8.75
V
0.55
0.79
0.97
V
1
2
3
µA
EN/UVLO rising
1.17
1.23
1.29
V
VEN/UVLO = 2.4 V
1.5
3.5
5.5
µA
4.30
5.65
7.25
µA
BIAS
VBIAS(SW)
EN/UVLO
SS
EA (ERROR AMPLIFIER)
VREF
Feedback reference voltage
gmEA
Error amplifier gm
FB = COMP
0.788
ISINK/ISOURCE
COMP sink/source current
ROUT
Amplifier output resistance
BW
Unity gain bandwidth
IBIAS(FB)
Feedback pin input bias current
FB in regulation
fSW(1)
Switching Frequency 1
RT = 133 kΩ
180
200
220
fSW(2)
Switching Frequency 2
RT = 47 kΩ
430
500
565
VFB=VREF ± 300 mV
0.800
0.812
V
1.27
mS
280
µA
20
MΩ
2
MHz
100
nA
FREQUENCY
(1)
6
kHz
All minimum and maximum limits are specified by correlating the electrical characteristics to process and temperature variations and
applying statistical process control.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
Electrical Characteristics (continued)
Typical values correspond to TJ = 25°C. Minimum and maximum limits apply over the –40°C to 125°C junction temperature
range unless otherwise stated. VIN = 24 V unless otherwise stated.(1)
PARAMETER
TEST CONDITION
MIN
TYP
MAX
UNIT
DITHER
IDITHER
Dither source/sink current
10.5
VDITHER
Dither high threshold
1.27
Dither low threshold
1.16
µA
V
SYNC
VSYNC
Sync input high threshold
2.1
Sync input low threshold
PWSYNC
1.2
Sync input pulse width
75
500
V
ns
CURRENT LIMIT
VCS(BUCK)
Buck current limit threshold (Valley)
VIN = VVISNS = 24 V, VVOSNS = 12 V,
VSLOPE = 0 V, TJ = 25°C
53.2
76
98
VCS(BOOST)
Boost current limit threshold (Peak)
VIN = VVISNS = 12 V, VVOSNS = 18 V,
VSLOPE = 0 V, TJ = 25°C
119
170
221
IBIAS(CS/CSG)
CS/CSG pin bias current
VCS = VCSG = 0 V
IOFFSET(CS/CS
CSG pin bias current
VCS = VCSG = 0 V
mV
-75
14
µA
G)
CONSTANT CURRENT LOOP
VSNS
Average current loop regulation target
VISNS(-) = 24 V, sweep ISNS(+), VSS =
0.8 V
ISNS
ISNS(+)/ISNS(–) pin bias currents
VISNS(+) = VISNS(–) = VIN = 24 V
7
µA
Gm
gm of soft-start pull down amplifier
VISNS(+)–VISNS(–) = 55 mV, VSS = 0.5
V
1
mS
Buck adaptive slope current
VIN = VVINSNS = 24 V, VVOSNS = 12 V,
VSLOPE = 0 V
24
30
35
Boost adaptive slope current
VIN = VVINSNS = 12 V, VVOSNS = 18 V,
VSLOPE = 0 V
13
17
21
43
50
57
mV
SLOPE
ISLOPE
gmSLOPE
µA
Slope compensation amplifier gm
2
µS
MODE
IMODE
Source current out of MODE pin
17
20
23
VDCM_HIC
DCM with hiccup threshold
0.60
0.7
0.76
VCCM_HIC
CCM with hiccup threshold
1.18
1.28
1.38
VCCM
CCM no hiccup threshold
2.22
2.4
2.6
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
µA
V
7
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
Electrical Characteristics (continued)
Typical values correspond to TJ = 25°C. Minimum and maximum limits apply over the –40°C to 125°C junction temperature
range unless otherwise stated. VIN = 24 V unless otherwise stated.(1)
PARAMETER
TEST CONDITION
MIN
TYP
MAX
UNIT
PGOOD
VPGD
PGOOD trip threshold for falling FB
Measured with respect to VREF
–9
%
PGOOD trip threshold for rising FB
Measured with respect to VREF
10
%
1.6
%
Hysteresis
ILEAK(PGD)
PGOOD leakage current
ISINK(PGD)
PGOOD sink current
VPGOOD = 0.4 V
Output overvoltage threshold
At the FB pin
2
4.2
100
nA
6.5
mA
OUTPUT OVP
VOVP
Hysteresis
0.86
21
V
mV
NMOS DRIVERS
IHDRV1,2
ILDRV1,2
RHDRV1,2
VUV(BOOT1,2)
Driver peak source current
VBOOT - VSW = 7 V
1.8
Driver peak sink current
VBOOT - VSW = 7 V
2.2
Driver peak source current
1.8
Driver peak sink current
2.2
Driver pull up resistance
VBOOT - VSW = 7 V
1.9
Driver pull down resistance
VBOOT - VSW = 7 V
1.3
BOOT1,2 to SW1,2 UVLO threshold
HDRV1,2 shut off
2.73
V
BOOT1,2 to SW1,2 UVLO hysteresis
HDRV1,2 start switching
280
mV
4.45
V
BOOT1,2 to SW1,2 threshold for refresh
pulse
RLDRV1,2
A
Driver pull up resistance
IDRV1,2 = 0.1 A
2
Driver pull down resistance
IDRV1,2 = 0.1 A
1.5
tDT1
Dead time HDRV1,2 off to LDRV1,2 on
55
tDT2
Dead time LDRV1,2 off to HDRV1,2 on
55
Ω
Ω
ns
THERMAL SHUTDOWN
TSD
Thermal shutdown temperature
TSD(HYS)
Thermal shutdown hysteresis
8
165
15
Submit Documentation Feedback
°C
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
7.6 Typical Characteristics
At TA = 25°C, unless otherwise stated.
100
99
98
EFFICIENCY (%)
EFFICIENCY (%)
95
97
96
95
90
85
VIN=6V
VIN=12V
VIN=24V
94
80
93
5
10
15
20
VOUT=12 V
IOUT=3 A
25
VIN (V)
30
35
40
0
45
1
2
3
4
LOAD CURRENT (A)
D009
L1=4.7 μH
Fsw=300 kHz
VOUT =12 V
Figure 1. Efficiency vs VIN
5
6
D008
L1=4.7 μH
Fsw=300 kHz
Figure 2. Efficiency vs Load
8
600
6
400
VCC (V)
FREQUENCY (kHz)
500
300
4
2
200
0
100
0
50
100
150
RT (k:)
200
250
0
300
2
4
6
12
14
16
18
D002
Figure 4. VCC vs VIN
Figure 3. Oscillator Frequency
1
2.4
0.8
2.2
0.6
2
IIN (mA)
IIN (mA)
8
10
VIN (V)
D004
0.4
0.2
1.8
1.6
BIAS = 12V
BIAS = 0V
BIAS = 12V
BIAS = 0V
0
1.4
0
5
10
15
20
25
VIN (V)
30
35
40
45
0
D006
Figure 5. IIN Standby
5
10
15
20
25
VIN (V)
30
35
40
45
D007
Figure 6. IIN Operating vs VIN
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
9
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
Typical Characteristics (continued)
4
1.30
3.2
1.26
VEN/UVLO (V)
IIN (PA)
At TA = 25°C, unless otherwise stated.
2.4
1.6
0.8
0
5
10
15
20
25
VIN (V)
30
35
40
1.10
-40
45
Figure 7. IIN Shutdown vs VIN
0
20
40
60
80
TEMPERATURE (°C)
100
120
140
D013
Figure 8. ENABLE/UVLO Rising Threshold vs Temperature
200
BOOST CURRENT LIMIT (mV)
BUCK CURRENT LIMIT (mV)
-20
D010
110
100
90
80
70
60
50
-40
1.18
1.14
-40 °C
25 °C
125 °C
0
1.22
-20
0
20
40
60
80
TEMPERATURE (qC)
100
120
140
190
180
170
160
150
140
-40
-20
0
D012
Figure 9. Buck Current Limit vs Temperature
20
40
60
80
TEMPERATURE (°C)
100
120
140
D011
Figure 10. Boost Current Limit vs Temperature
0.805
SW1 (20V/div)
0.803
VREF (V)
SW2 (10V/div)
0.801
VOUT (200mV/div ac)
0.799
IL (5A/div)
0.797
5 µs/div
0.795
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
100
120
140
VOUT=12 V
Figure 12. Forced CCM Operation (Buck)
Figure 11. VREF vs Temperature
10
VIN=24 V
D014
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
Typical Characteristics (continued)
At TA = 25°C, unless otherwise stated.
SW1 (20V/div)
SW1 (20V/div)
SW2 (10V/div)
SW2 (10V/div)
VOUT (200mV/div ac)
VOUT (200mV/div ac)
IL (5A/div)
IL (5A/div)
5 µs/div
VOUT=12 V
VIN=6 V
5 µs/div
VOUT=12 V
Figure 13. Forced CCM Operation (Boost)
VIN=12 V
Figure 14. Forced CCM Operation (Buck-Boost)
VOUT (500 mV/div ac)
VOUT (500mV/div)
IL (5A/div)
IL (5A/div)
500 µs/div
500 µs/div
VIN=24 V
VOUT=12 V
Load 2A to 4A
VIN=6 V
VOUT=12 V
Load 2A to 4A
Figure 16. Load Step (Boost)
Figure 15. Load Step (Buck)
VOUT (500mV/div)
VOUT (1V/div)
COMP (1V/div)
VIN (10V/div)
IL (5A/div)
IL (5A/div)
500 µs/div
VIN=12 V
VOUT=12 V
Load 2A to 4A
5ms/div
VIN=8 V to 24 V
Figure 17. Load Step (Buck-Boost)
VOUT=12 V
IOUT=1A
Figure 18. Line Transient
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
11
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
Typical Characteristics (continued)
At TA = 25°C, unless otherwise stated.
VOUT (5V/div)
Release
Overload
Hiccup
IL (5A/div)
20ms/div
VIN=24 V
VOUT=12 V
Hiccup Enabled
Figure 19. Hiccup Mode Current Limit
8 Detailed Description
8.1 Overview
The LM5175 is a wide input voltage four-switch buck-boost controller IC with integrated drivers for N-channel
MOSFETs. It operates in the buck mode when VIN is greater than VOUT and in the boost mode when VIN is less
than VOUT. When VIN is close to VOUT, the device operates in a proprietary transition buck or boost mode. The
control scheme provides smooth operation for any input/output combination within the specified operating range.
The buck or boost transition control scheme provides a low ripple output voltage when VIN equals VOUT without
compromising the efficiency.
The LM5175 integrates four N-Channel MOSFET drivers including two low-side drivers and two high-side drivers,
eliminating the need for external drivers or floating bias supplies. The internal VCC regulator supplies internal
bias rails as well as the MOSFET gate drivers. The VCC regulator is powered either from the input voltage
through the VIN pin or from the output or an external supply through the BIAS pin for improved efficiency.
The PWM control scheme is based on valley current mode control for buck operation and peak current mode
control for boost operation. The inductor current is sensed through a single sense resistor in series with the lowside MOSFETs. The sensed current is also monitored for cycle-by-cycle current limit. The behavior of the
LM5175 during an overload condition is dependent on the MODE pin programming (see MODE Pin
Configuration). If hiccup mode fault protection is selected, the controller turns off after a fixed number of
switching cycles in cycle-by-cycle current limit and restarts after another fixed number of clock cycles. The hiccup
mode reduces the heating in the power components in a sustained overload condition. If hiccup mode is disabled
through the MODE pin, the controller remains in a cycle-by-cycle current limit condition until the overload is
removed. The MODE pin also selects continuous conduction mode (CCM) for noise sensitive applications or
discontinuous conduction mode (DCM) for higher light load efficiency.
In addition to the cycle-by-cycle current limiting, the LM5175 also provides an optional average current regulation
loop that can be configured for either input or output current limiting. This is useful for battery charging or other
applications where a constant current behavior may be required.
The soft-start time of LM5175 is programmed by a capacitor connected to the SS pin to minimize the inrush
current and overshoot during startup.
The precision EN/UVLO pin supports programmable input undervoltage lockout (UVLO) with hysteresis. The
output overvoltage protection (OVP) feature turns off the high-side drivers when the voltage at the FB pin is 7.5%
above the nominal 0.8-V VREF. The PGOOD output indicates when the FB voltage is inside a ±10% regulation
window centered at VREF.
12
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
8.2 Functional Block Diagram
VIN
BIAS
3.5 µA
+
-
EN/UVLO
1.23 V
VCC
OPERATING
EN & BIAS
LOGIC
1.5 µA
+
-
0.7 V
THERMAL
SHUTDOWN
STANDBY
45 mV
1.2 V
PGOOD
+
0.88 V
OV
0.86 V
FB
+
+
5 µA
-
SS
+
ISNS(+)
-
ISNS(-)
+
1 mA/V
0.72 V
CONSTANT
CURRENT LOOP
3.3 V
0.8 V
SS
+
+
FB
-
GM ERROR
AMPLIFIER
BOOT1
PWM
COMPARATOR
1.6 V
HDRV1
+
-
SW1
VCC
LDRV1
COMP
CS
AMPLIFIER
CS
CLK
HDRV2
ILIMIT
COMPARATOR
-
SW2
+
VISNS
BOOT2
+
A=5
CSG
BUCK-BOOST CONTROLLER
LOGIC
VCC
LDRV2
VILIM
SLOPE
COMP
VOSNS
CCM/DCM
&
HICCUP CURRENT
LIMIT
SLOPE
RT/SYNC
OSC/SYNC
MODE
CLK
DITH
AGND
PGND
Copyright © 2016, Texas Instruments Incorporated
8.3 Feature Description
8.3.1 Fixed Frequency Valley/Peak Current Mode Control with Slope Compensation
The LM5175 implements a fixed frequency current mode control of both the buck and boost switches. The output
voltage, scaled down by the feedback resistor divider, appears at the FB pin and is compared to the internal
reference (VREF) by an internal error amplifier. The error amplifier produces an error voltage by driving the COMP
pin. An adaptive slope compensation signal based on VIN, VOUT, and the capacitor at the SLOPE pin is added to
the current sense signal measured across the CS and CSG pins. The result is compared to the COMP error
voltage by the PWM comparator.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
13
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
Feature Description (continued)
The LM5175 regulates the output using valley current mode control in buck mode and peak current mode control
in boost mode. For valley current mode control, the high-side buck MOSFET controlled by HDRV1 is turned on
by the PWM comparator at the valley of the inductor ripple current and turned off by the oscillator clock signal.
Valley current mode control is advantageous for buck converters where the PWM controller must resolve very
short on-times. For peak current mode control in the boost mode, the low-side boost MOSFET controlled by
LDRV2 is turned on by the clock signal in each switching cycle and turned off by the PWM comparator at the
peak of the inductor ripple current.
The low-side gate drive LDRV1, complementary to the HDRV1 drive signal, controls the synchronous rectification
MOSFET of the buck stage. The high-side gate drive HDRV2, complementary to the low-side gate drive LDRV2,
controls the high-side synchronous rectifier of the boost stage. For operation with VIN close to VOUT, the LM5175
uses a proprietary buck or boost transition scheme to achieve smooth, low ripple transition zone behavior.
Peak and valley current mode controllers require slope compensation for stable current loop operation at duty
cycle greater than 50% in peak current mode control and less than 50% in valley current mode control. The
LM5175 provides a SLOPE pin to program optimum slope for any VIN and VOUT combination using an external
capacitor.
8.3.2 VCC Regulator and Optional BIAS Input
The VCC regulator provides a regulated 7.5-V bias supply to the gate drivers. When EN/UVLO is above the 0.7V (typical) standby threshold, the VCC regulator is turned on. For VIN less than 7.5 V, the VCC voltage tracks VIN
with a small voltage drop as shown in Figure 4. If the EN/UVLO input is above the 1.23 V operating threshold
and VCC exceeds the 3.3 V (typical) VCC UV threshold, the controller is enabled and switching begins.
The VCC regulator draws power from VIN when there is no supply voltage connected to the BIAS pin. If the BIAS
pin is connected to an external voltage source that exceeds VCC by one diode drop, the VCC regulator draws
power from the BIAS input instead of VIN. Connecting the BIAS pin to VOUT in applications with VOUT greater than
8.5 V improves the efficiency of the regulator in the buck mode. The BIAS pin voltage should not exceed 36 V.
For low VIN operation, ensure that the VCC voltage is sufficient to fully enhance the MOSFETs. Use an external
bias supply if VIN dips below the voltage required to sustain the VCC voltage. For these conditions, use a series
blocking diode between the input supply and the VIN pin (Figure 20). This prevents VCC from back-feeding into
VIN through the body diode of the VCC regulator.
A 1-µF capacitor to PGND is required to supply the VCC regulator load transients.
Series Blocking
Diode
VIN
VIN
CVIN
LM5175
BIAS
Optional
Bias Supply/
VOUT
CBIAS
VCC
CVCC
Copyright © 2016, Texas Instruments Incorporated
Figure 20. VCC Regulator
14
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
Feature Description (continued)
8.3.3 Enable/UVLO
The LM5175 has a dual function enable and undervoltage lockout (UVLO) circuit. The EN/UVLO pin has three
distinct voltage ranges: shutdown, standby, and operating (see Shutdown, Standby, and Operating Modes).
When the EN/UVLO pin is below the standby threshold (0.7 V typical), the converter is held in a low power
shutdown mode. When EN/UVLO voltage is greater than the standby threshold but less than the 1.23 V
operating threshold, the internal bias rails and the VCC regulator are enabled but the soft-start (SS) pin is held
low and the PWM controller is disabled. A 1.5 µA pull-up current is sourced out of the EN/UVLO pin in standby
mode to provide hysteresis between the shutdown mode and the standby mode. When EN/UVLO is greater than
the 1.23 V operating threshold, the controller commences operation if VCC is above VCC UV threshold (3.3 V). A
hysteresis current of 3.5 µA is sourced into the EN/UVLO pin when the EN/UVLO input exceeds the 1.23 V
operation threshold to provide hysteresis that prevents on/off chattering in the presence of noise with a slowly
changing input voltage.
The VIN undervoltage lockout turn-on threshold is typically set by a resistor divider from the VIN pin to AGND with
the mid-point of the divider connected to EN/UVLO. The turn-on threshold VINUV is calculated using Equation 1
where RUV2 is the upper resistor and RUV1 is the lower resistor in the EN/UVLO resistor divider:
VIN(UV)
§ RUV2 ·
1.23 V u ¨ 1
¸ RUV2 u 1.5 PA
RUV1 ¹
©
(1)
The hysteresis between the UVLO turn-on threshold and turn-off threshold is set by the upper resistor in the
EN/UVLO resistor divider and is given by:
'VHYS(UV) 3.5 PA u RUV2
(2)
VIN
LM5175
RUV2
EN/UVLO
RUV1
Copyright © 2016, Texas Instruments Incorporated
Figure 21. UVLO Threshold Programming
8.3.4 Soft-Start
The LM5175 soft-start time is programmed using a soft-start capacitor from the SS pin to AGND. When the
converter is enabled, an internal 5-µA current source charges the soft-start capacitor. When the SS pin voltage is
below the 0.8-V feedback reference voltage VREF, the soft-start pin controls the regulated FB voltage. Once SS
exceeds VREF, the soft-start interval is complete and the error amplifier is referenced to VREF. The soft-start time
is given by Equation 3:
CSS u 0.8 V
t ss
5 PA
(3)
The soft-start capacitor is internally discharged when the converter is disabled because of EN/UVLO falling
below the operation threshold or VCC falling below the VCC UV threshold. The soft-start pin is also discharged
when the converter is in hiccup mode current limiting or in thermal shutdown. When average input or output
current limiting is active, the soft-start capacitor is discharged by the constant current loop transconductance
(gm) amplifier to limit either input or output current.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
15
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
Feature Description (continued)
8.3.5 Overcurrent Protection
The LM5175 provides cycle-by-cycle current limit to protect against overcurrent and short circuit conditions. In
buck operation, the sensed valley voltage across the CSG and CS pins is limited to 76 mV. The high-side buck
switch skips a cycle if the sensed voltage does not fall below this threshold during the buck switch off time. In
boost operation, the maximum peak voltage across CS and CSG is limited to 170mV. If the peak current in the
low-side boost switch causes the CS pin to exceed this threshold voltage, the boost switch is turned off for the
remainder of the clock cycle.
Applying the appropriate voltage to the MODE pin of the LM5175 enables hiccup mode fault protection (see
MODE Pin Configuration). In the hiccup mode, the controller shuts down after detecting cycle-by-cycle current
limiting for 128 consecutive cycles and the soft-start capacitor is discharged. The soft-start capacitor is
automatically released after 4000 oscillator clock cycles and the controller restarts. If hiccup mode protection is
not enabled through the MODE pin, the LM5175 will operate in cycle-by-cycle current limiting as long as the
overload condition persists.
8.3.6 Average Input/Output Current Limiting
The LM5175 provides optional average current limiting capability to limit either the input or the output current of
the DC/DC converter. The average current limiting circuit uses an additional current sense resistor connected in
series with the input supply or output voltage of the converter. A current sense gm amplifier with inputs at the
ISNS(+) and ISNS(-) pins monitors the voltage across the sense resistor and compares it with an internal 50 mV
reference. If the drop across the sense resistor is greater than 50 mV, the gm amplifier gradually discharges the
soft-start capacitor. When the soft-start capacitor discharges below the 0.8-V feedback reference voltage VREF,
the output voltage of the converter decreases to limit the input or output current. The average current limiting
feature can be used in applications requiring a regulated current from the input supply or into the load. The target
constant current is given by Equation 4:
50 mV
ICL(AVG)
RSNS
(4)
The average current loop can be disabled by shorting the ISNS(+) and ISNS(-) pins together.
8.3.7 CCM/DCM Operation
The LM5175 allows selection of continuous conduction mode (CCM) or discontinuous conduction mode (DCM)
operation using the MODE pin (see MODE Pin Configuration). In CCM operation the inductor current can flow in
either direction and the controller switches at a fixed frequency regardless of the load current. This mode is
useful for noise-sensitive applications where a fixed switching eases filter design. In DCM operation the
synchronous rectifier MOSFETs emulate diodes as LDRV1 or HDRV2 turn-off for the remainder of the PWM
cycle when the inductor current reaches zero. The DCM mode results in reduced frequency operation at light
loads, which lowers switching losses and increases light load efficiency of the converter.
8.3.8 Frequency and Synchronization (RT/SYNC)
The LM5175 switching frequency can be programmed between 100 kHz and 600 kHz using a resistor from the
RT/SYNC pin to AGND. The RT resistor is related to the nominal switching frequency (Fsw) by the following
equation:
§ 1 ·
¨
¸ 200 ns
Fsw ¹
©
RT
37 pF
(5)
Figure 3 in the Typical Characteristics shows the relationship between the programmed switching frequency (Fsw)
and the RT resistor.
The RT/SYNC pin can also be used for synchronizing the internal oscillator to an external clock signal. The
external synchronization pulse is ac coupled using a capacitor to the RT/SYNC pin. The voltage at the RT/SYNC
pin must not exceed 3.3 V peak. The external synchronization pulse frequency should be higher than the
internally set oscillator frequency and the pulse width should be between 75 ns and 500 ns.
16
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
Feature Description (continued)
LM5175
RT/SYNC
external SYNC
CSYNC
RT
Copyright © 2016, Texas Instruments Incorporated
Figure 22. Using External SYNC
8.3.9 Frequency Dithering
The LM5175 provides an optional frequency dithering function that is enabled by connecting a capacitor from
DITH to AGND. Figure 23 illustrates the dithering circuit. A triangular waveform centered at 1.22 V is generated
across the CDITH capacitor. This triangular waveform modulates the oscillator frequency by ±5% of the nominal
frequency set by the RT resistor. The CDITH capacitance value sets the rate of the low frequency modulation. A
lower CDITH capacitance will modulate the oscillator frequency at a faster rate than a higher capacitance. For the
dithering circuit to effectively reduce peak EMI, the modulation rate must be much less than the oscillator
frequency (Fsw). Equation 6 calculates the DITH pin capacitance required to set the modulation frequency, FMOD.
Connecting the DITH pin directly to AGND disables frequency dithering, and the internal oscillator operates at a
fixed frequency set by the RT resistor. Dither is disabled when external SYNC is used.
10 PA
CDITH
FMOD u 0.24 V
(6)
1.22 V + 5%
LM5175
1.22 V
1.22 V - 5 %
DITH
CDITH
Copyright © 2016, Texas Instruments Incorporated
Figure 23. Dither Operation
8.3.10 Output Overvoltage Protection (OVP)
The LM5175 provides an output overvoltage protection (OVP) circuit that turns off the gate drives when the
feedback voltage is 7.5% above the 0.8 V feedback reference voltage VREF. Switching resumes once the output
falls within 5% of VREF.
8.3.11 Power Good (PGOOD)
PGOOD is an open drain output that is pulled low when the voltage at the FB pin is outside -9% / +10% of the
nominal 0.8-V reference voltage. The PGOOD internal N-Channel MOSFET pull-down strength is typically 4.2
mA. This pin can be connected to a voltage supply of up to 8 V through a pull-up resistor.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
17
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
Feature Description (continued)
8.3.12 Gm Error Amplifier
The LM5175 has a gm error amplifier for loop compensation. The gm amplifier output (COMP) range is 0.3 V to
3 V. Connect an Rc1-Cc1 compensation network between COMP and ground for type II (PI) compensation (see
Figure 24). Another pole is usually added using Cc2 to suppress higher frequency noise.
The COMP output voltage (VCOMP) range limits the possible VIN and IOUT range for a given design. In buck mode,
the maximum VIN for which the converter can regulate the output at no load is when VCOMP reaches 0.3 V.
Equation 7 gives VCOMP as a function of VIN at no load in CCM buck mode:
2 PS ˜ VIN VOUT 6 PA
VOUT
˜ 1 DBUCK
˜ 1 DBUCK
VCOMP(BUCK) 1.6 V ACS ˜ RSENSE ˜
2 ˜ L1˜ Fsw
CSLOPE ˜ Fsw
(7)
Where DBUCK in the equation Equation 7 is the buck duty cycle given by:
VOUT
DBUCK
VIN
(8)
A larger L1, lower slope ripple (higher CSLOPE), smaller sense resistor (RSENSE), and higher frequency can
increase the maximum VIN range for buck operation.
For boost mode, the minimum VIN for which the converter can regulate the output at full load is when VCOMP
reaches 3 V. Equation 9 gives VCOMP as a function of VIN in boost mode:
§
· 2 PS ˜ VOUT VIN 5 PA
V
VIN
VCOMP(BOOST) 1.6 V ACS ˜ RSENSE ˜ ¨ IOUT ˜ OUT
˜ DBOOST ¸
˜ DBOOST
VIN
2 ˜ L1˜ Fsw
CSLOPE ˜ Fsw
©
¹
(9)
Where DBOOST in the Equation 9 is the boost duty cycle given by:
VIN
DBOOST 1
VOUT
(10)
A larger L1, lower slope ripple (higher CSLOPE), smaller sense resistor (RSENSE), and higher frequency can extend
the minimum VIN range for boost operation.
8.3.13 Integrated Gate Drivers
The LM5175 provides four N-channel MOSFET gate drivers: two floating high-side gate drivers at the HDRV1
and HDRV2 pins, and two ground referenced low-side drivers at the LDRV1 and LDRV2 pins. Each driver is
capable of sourcing 1.5 A and sinking 2 A peak current. In buck operation, LDRV1 and HDRV1 are switched by
the PWM controller while HDRV2 remains continuously on. In boost operation, LDRV2 and HDRV2 are switched
while HDRV1 remains continuously on.
In DCM buck operation, LDRV1 and HDRV2 turn off when the inductor current drops to zero (diode emulation).
In a DCM boost operation, HDRV2 turns off when inductor current drops to zero.
The gate drive output HDRV2 remains off during soft-start to prevent reverse current flow from a pre-biased
output.
The low-side gate drivers are powered from VCC and the high-side gate drivers HDRV1 and HDRV2 are
powered from bootstrap capacitors CBOOT1 (between BOOT1 and SW1) and CBOOT2 (between BOOT2 and SW2)
respectively. The CBOOT1 and CBOOT2 capacitors are charged through external Schottky diodes connected to the
VCC pin as shown in Figure 24.
8.3.14 Thermal Shutdown
The LM5175 is protected by a thermal shutdown circuit that shuts down the device when the internal junction
temperature exceeds 165°C (typical). The soft-start capacitor is discharged when thermal shutdown is triggered
and the gate drivers are disabled. The converter automatically restarts when the junction temperature drops by
the thermal shutdown hysteresis of 15°C below the thermal shutdown threshold.
18
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
8.4 Device Functional Modes
Please refer to Enable/UVLO section for the description of EN/UVLO pin function. Shutdown, Standby, and
Operating Modes section lists the shutdown, standby, and operating modes for LM5175 as a function of
EN/UVLO and VCC voltages.
8.4.1 Shutdown, Standby, and Operating Modes
EN/UVLO
VCC
DEVICE MODE
EN/UVLO < 0.7 V
—
Shutdown: VCC off, No switching
0.7 V < EN/UVLO < 1.23 V
—
Standby: VCC on, No switching
EN/UVLO > 1.23 V
VCC < 3.3 V
Standby: VCC on, No switching
EN/UVLO > 1.23 V
VCC > 3.3 V
Operating: VCC on, Switching enabled
8.4.2 MODE Pin Configuration
The MODE pin is used to select CCM/DCM operation and hiccup mode current limit. Mode is latched at startup.
MODE PIN CONNECTION
LIGHT LOAD MODE
HICCUP FAULT PROTECTION
Connect to VCC
CCM
No Hiccup
RMODE to AGND = 93.1 kΩ
CCM
Hiccup Enabled
RMODE to AGND = 49.9 kΩ
DCM
Hiccup Enabled
Connect to AGND
DCM
No Hiccup
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
19
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LM5175 is a four-switch buck-boost controller. A quick-start tool on the LM5175 product webpage can be
used to design a buck-boost converter using the LM5175. Alternatively, Webench®software can create a
complete buck-boost design using the LM5175 and generate bill of materials, estimate efficiency, solution size,
and cost of the complete solution. The following sections describe a detailed step-by-step design procedure for a
typical application circuit.
9.2 Typical Application
A typical application example is a buck-boost converter operating from a wide input voltage range of 6 V to 36 V
and providing a stable 12 V output voltage with current capability of 6 A.
RSNS
0Ÿ
VIN
0.1 µF
CVIN
100 Ÿ
CIN
68 µF
RUV2
249 NŸ
10 Ÿ
RUV1
59.0 NŸ
1 µF
CIN
4.7 µF
x5
100 Ÿ
COUT
10 µF
x5
QH1
EN/UVLO
VINSNS
VIN
ISNS(-)
VOUT
COUT
180 µF
x2
QH2
ISNS(+)
HDRV1
VCC
10 NŸ
RMODE
CBOOT1
0.1 µF
SW1
MODE
93.1 NŸ
L1
VCC
BOOT1
PGOOD
4.7 µH
QL1
QL2
LDRV1
100 Ÿ
RT/SYNC
CS
CSYNC
1 nF RT
84.5 NŸ
RSENSE
8 PŸ
47 pF
CSG
LM5175
100 Ÿ
SS
CSS
0.1 µF
VOUT
LDRV2
BIAS
BOOT2
CBIAS
0.1 µF
SW2
AGND
PGND
VCC
CBOOT2
0.1 µF
HDRV2
VOSNS
VCC
COMP
DITH
CVCC
1 µF
SLOPE
Cc1
22 nF
Cc2
100 pF
Rc1
10 NŸ
CSLOPE
100 pF R
RB1
20 NŸ
FB
RRB2
280 NŸ
Copyright © 2016, Texas Instruments Incorporated
Figure 24. LM5175 Four-Switch Buck Boost Application Schematic
20
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
Typical Application (continued)
9.2.1 Design Requirements
For this design example, the following are used as the input parameters.
DESIGN PARAMETER
EXAMPLE VALUE
Input Voltage Range
6 V to 36 V
Output
12 V
Load Current
6A
Switching Frequency
300 kHz
Mode
CCM, Hiccup
9.2.2 Detailed Design Procedure
9.2.2.1 Frequency
The switching frequency of LM5175 is set by an RT resistor connected from RT/SYNC pin to AGND. The RT
resistor required to set the desired frequency is calculated using Equation 5 or Figure 3 . A 1% standard resistor
of 84.5 kΩ is selected for Fsw = 300 kHz.
9.2.2.2 VOUT
The output voltage is set using a resistor divider to the FB pin. The internal reference voltage is 0.8 V. Normally
the bottom resistor in the resistor divider is selected to be in the 1 kΩ to 100 kΩ range. Select
RFB1 20 k:
(11)
The top resistor in the feedback resistor divider is selected using Equation 12:
VOUT 0.8 V
u RFB1 280 k:
RFB2
0.8 V
(12)
9.2.2.3 Inductor Selection
The inductor selection is based on consideration of both buck and boost modes of operation. For the buck mode,
inductor selection is based on limiting the peak to peak current ripple ΔIL to ~40% of the maximum inductor
current at the maximum input voltage. The target inductance for the buck mode is:
(VIN(MAX) VOUT ) u VOUT
LBUCK
11.1 PH
0.4 u IOUT(MAX) u Fsw u VIN(MAX)
(13)
For the boost mode, the inductor selection is based on limiting the peak to peak current ripple ΔIL to ~40% of the
maximum inductor current at the minimum input voltage. The target inductance for the boost mode is:
LBOOST
2
VIN(MIN)
u (VOUT
VIN(MIN) )
2
0.4 u IOUT(MAX) u Fsw u VOUT
2.1 PH
(14)
In this particular application, the buck inductance is larger. Choosing a larger inductance reduces the ripple
current but also increases the size of the inductor. A larger inductor also reduces the achievable bandwidth of the
converter by moving the right half plane zero to lower frequencies. Therefore a judicious compromise should be
made based on the application requirements. For this design a 4.7-µH inductor is selected. With this inductor
selection, the inductor current ripple is 5.7 A, 4.3 A, and 2.1 A, at VIN of 36 V, 24 V, and 6 V respectively.
The maximum average inductor current occurs at the minimum input voltage and maximum load current:
VOUT u IOUT(MAX)
IL(MAX)
13.3 A
0.9 u VIN(MIN)
(15)
where a 90% efficiency is assumed. The peak inductor current occurs at minimum input voltage and is given by:
VIN(MIN) u (VOUT VIN(MIN) )
IL(PEAK) IL(MAX)
14.4 A
2 u L1u Fsw u VOUT
(16)
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
21
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
To ensure sufficient output current, the current limit threshold must be set to allow the maximum load current in
boost operation. To ensure that the inductor does not saturate in current limit, the peak saturation current of the
inductor should be higher than the maximum current limit. Adjusting for a ±20% current limit threshold tolerance,
the peak inductor current limit is:
1.2 u IL(PEAK)
IL(SAT)
21.6 A
0.8
(17)
Therefore, the inductor saturation current should be greater than 21.6 A. If hiccup mode protection is not
enabled, the RMS current rating of the inductor should be sufficient to tolerate continuous operation in cycle-bycycle current limiting.
9.2.2.4 Output Capacitor
In the boost mode, the output capacitor conducts high ripple current. The output capacitor RMS ripple current is
given by Equation 18 where the minimum VIN corresponds to the maximum capacitor current.
ICOUT(RMS)
IOUT u
VOUT
VIN
1
(18)
In this example the maximum output ripple RMS current is ICOUT(RMS) = 6 A. A 5-mΩ output capacitor ESR
causes an output ripple voltage of 60 mV as given by:
I
u VOUT
'VRIPPLE(ESR) OUT
u ESR
VIN(MIN)
(19)
A 400 µF output capacitor causes a capacitive ripple voltage of 25 mV as given by:
'VRIPPLE(COUT)
VIN(MIN) ·
§
IOUT u ¨ 1
¸
VOUT ¹
©
COUT u Fsw
(20)
Typically a combination of ceramic and bulk capacitors is needed to provide low ESR and high ripple current
capacity. The complete schematic in Figure 24 at the end of this section shows a good starting point for COUT for
typical applications.
9.2.2.5 Input Capacitor
In the buck mode, the input capacitor supplies high ripple current. The RMS current in the input capacitor is given
by:
ICIN(RMS)
IOUT D u (1 D)
(21)
The maximum RMS current occurs at D = 0.5, which gives ICIN(RMS) = IOUT/2 = 3 A. A combination of ceramic and
bulk capacitors should be used to provide short path for high di/dt current and to reduce the output voltage ripple.
The complete schematic in Figure 24 is a good starting point for CIN for typical applications.
9.2.2.6 Sense Resistor (RSENSE)
The current sense resistor between the CS and CSG pins should be selected to ensure that current limit is set
high enough for both buck and boost modes of operation. For the buck operation, the current limit resistor is
given by:
76 mV u 70%
RSENSE(BUCK)
8.8 m :
IOUT(MAX)
(22)
For the boost mode of operation, the current limit resistor is given by:
170 mV u 70%
RSENSE(BOOST)
8.2 m :
IL(PEAK)
(23)
The closest standard value of RSENSE = 8 mΩ is selected based on the boost mode operation.
22
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
The maximum power dissipation in RSENSE happens at VIN(MIN):
2
PRSENSE(MAX)
VIN(MIN) ·
§
§ 170mV ·
¸
¨
¸ ˜ RSENSE ˜ ¨¨ 1
VOUT ¸¹
© RSENSE ¹
©
1.8 W
(24)
Based on this, select the current sense resistor with power rating of 2 W or higher.
For some application circuits, it may be required to add a filter network to attenuate noise in the CS and CSG
sense lines. Please see Figure 24 for typical values. The filter resistance should not exceed 100 Ω.
9.2.2.7 Slope Compensation
For stable current loop operation and to avoid sub-harmonic oscillations, the slope capacitor should be selected
based on Equation 25:
L1
4.7 PH
CSLOPE gmSLOPE u
2 PS u
235 pF
RSENSE u ACS
8 m: u 5
(25)
This slope compensation results in “dead-beat” operation, in which the current loop disturbances die out in one
switching cycle. Theoretically a current mode loop is stable with half the “dead-beat” slope (twice the calculated
slope capacitor value in Equation 25). A smaller slope capacitor results in larger slope signal which is better for
noise immunity in the transition region (VIN~VOUT). A larger slope signal, however, restricts the achievable input
voltage range for a given output voltage, switching frequency, and inductor. For this design CSLOPE = 100 pF is
selected for better transition region behavior while still providing the required VIN range. This selection of slope
capacitor, inductor, switching frequency, and inductor satisfies the COMP range limitation explained in Gm Error
Amplifier section.
9.2.2.8 UVLO
The UVLO resistor divider must be designed for turn-on below 6V. Selecting a RUV2 = 249 kΩ gives a UVLO
hysteresis of 0.8 V. The lower UVLO resistor is the selected using Equation 26:
RUV2 u 1.23 V
RUV1
59.5 k:
VIN UV 1.5 PA u RUV2 1.23 V
(26)
A standard value of 59.0 kΩ is selected for RUV1.
When programming the UVLO threshold for lower input voltage operation, it is important to choose MOSFETs
with gate (Miller) plateau voltage lower than the minimum VIN.
9.2.2.9 Soft-Start Capacitor
The soft-start time is programmed using the soft-start capacitor. The relationship between CSS and the soft-start
time is given by:
0.8 V u CSS
t ss
5 PA
(27)
CSS = 0.1 µF gives a soft-start time of 16 ms.
9.2.2.10 Dither Capacitor
The dither capacitor sets the modulation frequency of the frequency dithering around the nominal switching
frequency. A larger CDITH results in lower modulation frequency. For proper operation the modulation frequency
(FMOD) must be much lower than the switching frequency. Use Equation 28 to select CDITH for the target
modulation frequency.
10 PA
CDITH
FMOD u 0.24 V
(28)
For the current design dithering is not being implemented. Therefore a 0 Ω resistor from the DITH pin to AGND
disables this feature.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
23
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
9.2.2.11 MOSFETs QH1 and QL1
The input side MOSFETs QH1 and QL1 need to withstand the maximum input voltage of 36 V. In addition they
must withstand the transient spikes at SW1 during switching. Therefore QH1 and QL1 should be rated for 60 V.
The gate plateau voltages of the MOSFETs should be smaller than the minimum input voltage of the converter,
otherwise the MOSFETs may not fully enhance during startup or overload conditions.
The power loss in QH1 in the boost mode of operation is approximated by:
2
PCOND(QH1)
§
VOUT ·
¨ IOUT ˜
¸ ˜ RDSON(QH1)
VIN ¹
©
(29)
The power loss in QH1 in the buck mode of operation consists of both conduction and switching loss
components given by Equation 30 and Equation 31 respectively:
PCOND(QH1)
PSW(QH1)
§ VOUT
¨
© VIN
·
2
¸ ˜ IOUT ˜ RDSON(QH1)
¹
1
˜ VIN ˜ IOUT ˜ tr
2
(30)
t f ˜ Fsw
(31)
The rise (tr) and the fall (tf) times are based on the MOSFET datasheet information or measured in the lab.
Typically a MOSFET with smaller RDSON (smaller conduction loss) will have longer rise and fall times (larger
switching loss).
The power loss in QL1 in the buck mode of operation is given by the following equation:
PCOND(QL1)
§
VOUT
¨1
VIN
©
·
2
¸ ˜ IOUT ˜ RDSON(QL1)
¹
(32)
9.2.2.12 MOSFETs QH2 and QL2
The output side MOSFETs QH2 and QL2 see the output voltage of 12 V and additional transient spikes at SW2
during switching. Therefore QH2 and QL2 should be rated for 20 V or more. The gate plateau voltages of the
MOSFETs should be smaller than the minimum input voltage of the converter, otherwise the MOSFETs may not
fully enhance during startup or overload conditions.
The power loss in QH2 in the buck mode of operation is approximated by:
PCOND(QH2)
IOUT 2 ˜ RDSON(QH2)
(33)
The power loss in QL2 in the boost mode of operation consists of both conduction and switching loss
components given by Equation 34 and Equation 35 respectively:
PCOND(QL2)
PSW(QL2)
§
VIN
¨1
V
OUT
©
1
˜ VOUT
2
2
· §
VOUT ·
¸ ˜ ¨ IOUT ˜
¸ ˜ RDSON(QL2)
VIN ¹
¹ ©
§
V
˜ ¨ IOUT ˜ OUT
VIN
©
·
¸ ˜ tr
¹
(34)
t f ˜ Fsw
(35)
The rise (tr) and the fall (tf) times can be based on the MOSFET datasheet information or measured in the lab.
Typically a MOSFET with smaller RDSON (lower conduction loss) has longer rise and fall times (larger switching
loss).
The power loss in QH2 in the boost mode of operation is given by the following equation:
PCOND(QH2)
24
VIN
VOUT
2
§
·
V
˜ ¨ IOUT ˜ OUT ¸ ˜ RDSON(QH2)
VIN ¹
©
Submit Documentation Feedback
(36)
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
9.2.2.13 Frequency Compensation
This section presents the control loop compensation design procedure for the LM5175 buck-boost controller. The
LM5175 operates mainly in buck or boost modes, separated by a transition region, and therefore the control loop
design is done for both buck and boost operating modes. Then a final selection of compensation is made based
on the mode that is more restrictive from a loop stability point of view. Typically for a converter designed to go
deep into both buck and boost operating regions, the boost compensation design is more restrictive due to the
presence of a right half plane zero (RHPZ) in the boost mode.
The boost power stage output pole location is given by:
·
1 §
2
¦p1(boost)
+]
¨
¸
2S © ROUT u COUT ¹
(37)
where ROUT = 2 Ω corresponds to the maximum load of 6 A.
The boost power stage ESR zero location is given by:
·
1 §
1
¦ z1
N+]
¨
¸
2S © RESR u COUT ¹
(38)
The boost power stage RHP zero location is given by:
¦RHP
1 § ROUT u (1 DMAX )2 ·
¨
¸
¸
2S ¨©
L1
¹
N+]
(39)
where DMAX is the maximum duty cycle at the minimum VIN.
The buck power stage output pole location is given by:
¦p1(buck)
·
1 §
1
¨
¸
2S © ROUT u COUT ¹
+]
(40)
The buck power stage ESR zero location is the same as the boost power stage ESR zero.
It is clear from Equation 39 that RHP zero is the main factor limiting the achievable bandwidth. For a robust
design the crossover frequency should be less than 1/3 of the RHP zero frequency. Given the position of the
RHP zero, a reasonable target bandwidth in boost operation is around 4 kHz:
¦bw
N+]
(41)
For some power stages, the boost RHP zero might not be as restrictive. This happens when the boost maximum
duty cycle (DMAX) is small, or when a really small inductor is used. In those cases, compare the limits posed by
the RHP zero (fRHP/3) with 1/20 of the switching frequency and use the smaller of the two values as the
achievable bandwidth.
The compensation zero can be placed at 1.5 times the boost output pole frequency. Keep in mind that this
locates the zero at 3 times the buck output pole frequency which results in approximately 30 degrees of phase
loss before crossover of the buck loop and 15 degrees of phase loss at intermediate frequencies for the boost
loop:
¦ zc
+]
(42)
If the crossover frequency is well below the RHP zero and the compensation zero is placed well below the
crossover, the compensation gain resistor Rc1 is calculated using the approximation:
S u ¦bw RFB1 RFB2 $ CS u 5SENSE u &OUT
u
u
Rc1
9.49 k:
gmEA
RFB1
1 DMAX
(43)
where DMAX is the maximum duty cycle at the minimum VIN in boost mode and ACS is the current sense amplifier
gain. The compensation capacitor Cc1 is then calculated from:
1
Cc1
27.9 nF
u S u ¦ zc u 5c1
(44)
The standard values of compensation components are selected to be Rc1 = 10 kΩ and Cc1 = 22 nF.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
25
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
A high frequency pole is added to suppress switching noise using a 100 pF capacitor (Cc2) in parallel with Rc1
and Cc1. These values provide a good starting point for the compensation design. Each design should be tuned
in the lab to achieve the desired balance between stability margin across the operating range and transient
response time.
9.2.3 Application Curves
100
EFFICIENCY (%)
95
90
85
VIN=6V
VIN=12V
VIN=24V
80
0
1
2
3
4
LOAD CURRENT (A)
5
6
Figure 26. Output Voltage Ripple
D008
Figure 25. Efficiency vs Load
Figure 27. Load Transient Response
26
Figure 28. Line Transient Response (8 V - 24 V, IOUT = 2 A)
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
10 Power Supply Recommendations
The LM5175 is a power management device. The power supply for the device is any dc voltage source within the
specified input range. The supply should also be capable of supplying sufficient current based on the maximum
inductor current in boost mode operation. The input supply should be bypassed with additional electrolytic
capacitor at the input of the application board to avoid ringing due to parasitic impedance of the connecting
cables.
11 Layout
11.1 Layout Guidelines
The basic PCB board layout requires separation of sensitive signal and power paths. The following checklist
should be followed to get good performance for a well designed board.
• Place the power components including the input filter capacitor CIN, the power MOSFETs QL1 and QH1, and
the sense resistor RSENSE close together to minimize the loop area for input switching current in buck
operation.
• Place the power components including the output filter capacitor COUT, the power MOSFETs QL2 and QH2,
and the sense resistor RSENSE close together to minimize the loop area for output switching current in boost
operation.
• Use a combination of bulk capacitors and smaller ceramic capacitors with low series impedance for the input
and output capacitors. Place the smaller capacitors closer to the IC to provide a low impedance path for high
di/dt switching currents.
• Minimize the SW1 and SW2 loop areas as these are high dv/dt nodes.
• Layout the gate drive traces and return paths as directly as possible. Layout the forward and return traces
close together, either running side by side or on top of each other on adjacent layers to minimize the
inductance of the gate drive path.
• Use Kelvin connections to RSENSE for the current sense signals CS and CSG and run lines in parallel from the
RSENSE terminals to the IC pins. Avoid crossing noisy areas such as SW1 and SW2 nodes or high-side gate
drive traces. Place the filter capacitor for the current sense signal as close to the IC pins as possible.
• Place the CIN, COUT, and RSENSE ground pins as close as possible with thick ground trace and/or planes on
multiple layers.
• Place the VCC bypass capacitor close to the controller IC, between the VCC and PGND pins. A 1-µF ceramic
capacitor is typically used.
• Place the BIAS bypass capacitor close to the controller IC, between the BIAS and PGND pins. A 0.1-µF
ceramic capacitor is typically used.
• Place the BOOT1 bootstrap capacitor close to the IC and connect directly to the BOOT1 to SW1 pins.
• Place the BOOT2 bootstrap capacitor close to the IC and connect directly to the BOOT2 to SW2 pins.
• Bypass the VIN pin to AGND with a low ESR ceramic capacitor located close to the controller IC. A 0.1 µF
ceramic capacitor is typically used. When using external BIAS, use a diode between input rails and VIN pins to
prevent reverse conduction when VIN < VCC.
• Connect the feedback resistor divider between the COUT positive terminal and AGND pin of the IC. Place the
components close to the FB pin.
• Use care to separate the power and signal paths so that no power or switching current flows through the
AGND connections which can either corrupt the COMP, SLOPE, or SYNC signals, or cause dc offset in the
FB sense signal. The PGND and AGND traces can be connected near the PGND pin, near the VCC
capacitor PGND connection, or near the PGND connection of the CS, CSG pin current sense resistor.
• When using the average current loop, divide the overall capacitor (CIN or COUT) between the two sides of the
sense resistor to ensure small cycle-by-cycle ripple. Place the average current loop filter capacitor close to
the IC between the ISNS(+) and ISNS(-) pins.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
27
LM5175
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
www.ti.com
11.2 Layout Example
L1
SW1
SW2
VOUT
VIN
QL1
QL2
QH1
CIN
CIN
GND
QH2
RSENSE
RISNS
COUT
LM5175
COUT
GND
Figure 29. LM5175 Power Stage Layout
28
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
LM5175
www.ti.com
SNVSA37A – OCTOBER 2015 – REVISED MAY 2016
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
Please visit TI homepage for latest technical document including application notes, user guides, and reference
designs.
IC Package Thermal Metrics application report, SPRA953.
12.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.3 Trademarks
PowerPAD, E2E are trademarks of Texas Instruments.
Webench is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Product Folder Links: LM5175
29
PACKAGE OPTION ADDENDUM
www.ti.com
8-May-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM5175PWPR
ACTIVE
HTSSOP
PWP
28
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 125
LM5175
LM5175PWPT
ACTIVE
HTSSOP
PWP
28
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 125
LM5175
LM5175RHFR
ACTIVE
VQFN
RHF
28
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
LM5175
LM5175RHFT
ACTIVE
VQFN
RHF
28
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 125
LM5175
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
8-May-2016
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM5175 :
• Automotive: LM5175-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Jun-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM5175PWPR
HTSSOP
PWP
28
2000
330.0
16.4
6.9
10.2
1.8
12.0
16.0
Q1
LM5175PWPT
HTSSOP
PWP
28
250
180.0
LM5175RHFR
VQFN
RHF
28
3000
330.0
16.4
6.9
10.2
1.8
12.0
16.0
Q1
12.4
4.3
5.3
1.3
8.0
12.0
LM5175RHFT
VQFN
RHF
28
250
180.0
Q1
12.4
4.3
5.3
1.3
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Jun-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM5175PWPR
HTSSOP
PWP
28
2000
367.0
367.0
38.0
LM5175PWPT
HTSSOP
PWP
28
250
213.0
191.0
55.0
LM5175RHFR
VQFN
RHF
28
3000
367.0
367.0
35.0
LM5175RHFT
VQFN
RHF
28
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated