3 6 4 5 TIP RING 2 7 RJ31X TIP RING INCOMING TELCO 8 1 VISTA Series Panel Wiring Diagram PREMISES PHONES DIRECT CONNECT CORD VISTA SERIES RESIDENTIAL CONTROL 5 6 7 INCOMING PHONE LINE HANDSET ECP TERMINALS DATA DATA OUT 606* (two-way voice to follow) sent during the same call. GND AUX IN BRN GRY RED 8 (EARTH GND 7 4 (RING) 2 A “received” acknowledgement is sent back to the field radio, indicating the alarm was received and is in process (90 sec push off ack). 3 (RING) 6 2 (TIP) 1 A voice-enabled alarm message is received from a field radio and processed by the Message Processing Server(s). TRIGGER HEADER 1 (TIP) AlarmNet Two-Way Voice via GSM Step Step GRN KEYPAD 5 8 Line held open between digital dialer and central station. Acknowledgement sent from digital dialer to the field radio with “two-way voice” command and digital dialer phone number included. Alarm message delivery via phone line performed (800plus central station). Alarm message delivery acknowledgement sent by receiver back to digital dialer (phone line held open). BLK RED KEYPAD Important Notes • YEL DATA AUDIO GND +VDC USE EITHER AVS CONNECTIONS BUT NOT BOTH Field radio calls the digital dialer. Digital dialer identifies incoming call by the caller ID data. 10 Digital dialer bridges the two voice sessions together to create an end-to-end connection for the central station operator to the protected premises. AUDIO CABLE TB 1 1 2 3 4 5 6 7 8 9 10 11 GSM GPPS WEB MODE 2 MODE 1 RSSI 9 Universal control panel compatibility – flexible modes of operation allow ECP alarm reporting by Honeywell control panels, 4204 relay mode for Honeywell controls (that do not support ECP alarm reporting) and zone triggering for use with other control panels AVS BASE UNIT Control Panel Compatibility – The following VISTA Series families: VISTA-21iP, VISTA-20P (Rev 7 or higher) and VISTA-15P (Rev 6 or higher) Either AVS connection can be made(POTS or GSMV) – but not both • For detailed installation instructions refer to the panel installation guide • Two-way voice GSM model required • Two-way voice audio cable required Central Station Commands 1 – Speak 2 – VOX (talk & listen) 3 – Listen 7 – Extended session (two minute timeout) 9 – Disconnect two-way voice session LED PHONE PROGRAM MODE CALLBACK MODE DIP SW ON 1 PANEL TRIGGER MODE NORMAL MODE BASE UNIT DEVICE ADDRESS ON 2 3 4 1 2 3 4 5 HANDSET DEVICE ADDRESS (ADDRESS 8 SHOWN) RING TIP INCOMING PHONE LINE NOT USED GRY BRN TIP RING AUDIO CONNECTOR AAV VISTA-15P = 8 PANEL RED BLK GRN YEL RED BLK GRN YEL ECP RED BLK GRN YEL ON 1 2 3 4 5 VISTA-20P = 11 Ordering Information SUPPLIED HARNESS AAV YEL GRN GSMV (OPTIONAL) • IMPORTANT: DO NOT CONNECT ANY OTHER ECP DEVICES TO PANEL. USE AVS BASE UNIT ECP TERMINALS FOR OTHER ECP DEVICES. MIC *606 “Listen-in to follow”. The system is about to activate a two-way audio session. For additional programming please see instructional inserts. • GRN BLK VOLUME / ID BUTTON (200 FT. MAX) 3 4 Alarm delivery request sent to the digital dialer server with request for AlarmNet two-way voice processing. SPEAKERS LED RED AVST STATION 606* delivery acknowledgement sent by receiver back to digital dialer (phone line held open). BATTERY TO ALL OTHER ECP DEVICES ON 1 2 3 4 5 GSMVLP – Audio GSMV – Audio GSMX – Audio AVS – Audio Verification System AVST – Audio Verification Station L/VSTA2WYMP/D © 2010 Honeywell International Inc.