Surface Mount Aluminum Electrolytic Capacitors SHB Series (Bi-Polar, 105°C) MERITEK RoHS FEATURES Height : 5.4mm Load life : 105°C 1000 hours SHB series is Bi-Polar type SPECIFICATIONS Item Characteristic Operation Temperature Range -55 ~ +105°C Rated Working Voltage 6.3 ~ 50VDC Capacitance Tolerance ±20%(M) (120Hz 20°C) Leakage Current (20°C) I ≤0.05CV or 10 ( µA ) *Whichever is greater after 2 minutes I: Leakage Current ( µA) C: Rated Capacitance ( µF) V: Working Voltage (V) W.V. 6.3 10 16 25 35 50 (20°C) S.V. 8 13 20 32 44 63 Dissipation Factor (tan δ) (120Hz 20°C) W.V. 6.3 10 16 25 35 50 tan δ 0.26 0.22 0.20 0.20 0.20 0.18 Rated Voltage (V) 6.3 10 16 25 35 50 -25°C / +20°C 4 3 2 2 2 2 -40°C / +20°C 8 6 4 4 3 3 Surge Voltage Impedance ratio at 120Hz Low Temperature Stability After 1000 hours application of W.V. and +105°C ripple current value, the capacitor shall meet the following limits. (DC + ripple peak voltage ≤ rate working voltage) (The polarity need to exchange every 250 hours) Load Life Capacitance Change ≤ ±25% of initial value Dissipation Factor ≤ 200% of initial specified value Leakage current ≤ initial specified value At +105°C, no voltage application after 500 hours, the capacitor shall meet the limits for load life characteristics. (With voltage treatment) Shelf Life Capacitors placed on a 250°C hot plate for 30 seconds with their electrode terminals facing downward will fulfill the following conditions after being cooled to room temperature. Resistance to Soldering Heat Capacitance Change ≤ ±10% of initial value Dissipation Factor ≤ initial specified value Leakage current ≤ initial specified value PART NUMBERING SYSTEM SHB 50V Meritek Series Voltage Capacitance Capacitance expressed in microfarads (μF). First two digits are significant figures. Third digit denotes number of zeros. 'R' denotes decimal point for values less than 10 μF Tolerance M=±20% Case Diameter Code Case Height (mm) The third digit denotes the first decimal place For example, 054 = 5.4mm 470 M F 054 Case Diameter Code D E F ΦD Φ 4.0 Φ 5.0 Φ 6.3 Rev. 7a Surface Mount Aluminum Electrolytic Capacitors SHB Series (Bi-Polar, 105°C) MERITEK RoHS DIMENSIONS (mm) ΦD Φ 4.0 Φ 5.0 Φ 6.3 L 5.4 5.4 5.4 A 4.3 5.3 6.6 H 5.5MAX 6.5MAX 7.8MAX I 1.8 2.2 2.6 W 0.65±0.1 0.65±0.1 0.65±0.1 P 1.0 1.5 2.1 K +0.15 0.35 -0.20 +0.15 0.35 -0.20 +0.15 0.35 -0.20 CASE SIZE & MAX RIPPLE CURRENT V Cap. ( µF) Item 0.1 6.3 DxL Case size Max ripple current 10 R.C. DxL 16 R.C. DxL 25 R.C. DxL :D xL (mm) : mA(rms) 85°C 120Hz 35 R.C. DxL 50 R.C. DxL R.C. 0R1 4x5.4 2 0.22 R22 4x5.4 3 0.33 R33 4x5.4 4 0.47 R47 4x5.4 4 1.0 010 4x5.4 6 2.2 2R2 3.3 3R3 4.7 4R7 10 100 22 220 5x5.4 33 330 47 470 4x5.4 9 5x5.4 10 5x5.4 12 5x5.4 13 5x5.4 13 6.3x5.4 17 4x5.4 12 5x5.4 14 5x5.4 15 6.3x5.4 24 6.3x5.4 25 4x5.4 17 5x5.4 21 26 6.3x5.4 32 6.3x5.4 35 6.3x5.4 36 6.3x5.4 40 6.3x5.4 43 6.3x5.4 43 Rev. 7a Surface Mount Aluminum Electrolytic Capacitors SHB Series (Bi-Polar, 105°C) MERITEK RoHS TAPING DxL Ø4x5.4 Ø5x5.4 Ø6.3x5.4 Ø4x5.8 Ø5x5.8 Ø6.3x5.8 Ø6.3x7.7 Ø8x6.2 Ø8x10.2 Ø10x10.2 W ±0.3 12.0 12.0 16.0 12.0 12.0 16.0 16.0 16.0 24.0 24.0 A ±0.2 4.7 5.7 7.0 4.7 5.7 7.0 7.0 8.7 8.7 10.7 B ±0.2 4.7 5.7 7.0 4.7 5.7 7.0 7.0 8.7 8.7 10.7 P0 ±0.1 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 P1 ±0.1 8.0 12.0 12.0 8.0 12.0 12.0 12.0 12.0 16.0 16.0 P2 ±0.1 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 F ±0.1 5.5 5.5 7.5 5.5 5.5 7.5 7.5 7.5 11.5 11.5 ØD0 ±0.1 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 t1 ±0.1 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 E ±0.1 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 t2 ±0.2 5.7 5.7 5.7 6.3 6.4 6.4 8.2 6.8 11.0 11.0 PACKAGE DxL Ø4 Ø5 Ø6.3 Ø8x6.2 Ø8x10.2 Ø10x10.2 A ±2.0 380 380 380 380 380 B MIN 50 50 50 50 50 C ±0.5 13 13 13 13 13 D ±0.8 21 21 21 21 21 E ±0.5 2.0 2.0 2.0 2.0 2.0 W ±1.0 14.0 18.0 18.0 26.0 26.0 T ±1.0 20.0 24.0 24.0 32.0 32.0 t ±0.5 3.0 3.0 3.0 3.0 3.0 Rev. 7a Surface Mount Aluminum Electrolytic Capacitors SHB Series (Bi-Polar, 105°C) MERITEK RoHS PERMISSBLE REFLOW CONDITION AIR REFLOW AND IR REFLOW Preheat: Within 120sec., 190°C or less. Soldering Time: Within 50 sec., 230°C Peak Temperature: Less than 250°C, within 10 sec. Possible Reflow Cycle: 2 Cycles The final test values should be as following: (A) Capacitance change: ≦ ±10% of initial value (B) Dissipation factor: ≦ initial specified value (C) Leakage current: ≦ initial specified value (D) Visual: No damage Rev. 7a