LPC436x
32-bit ARM Cortex-M4/M0 MCU; up to 1 MB flash and 154 kB
SRAM; Ethernet, two High-speed USB, LCD, EMC
Rev. 1.2 — 14 March 2016
Product data sheet
1. General description
The LPC436x are ARM Cortex-M4 based microcontrollers for embedded applications,
which include an ARM Cortex-M0 coprocessor and an ARM Cortex-M0 subsystem for
managing peripherals, up to 1 MB of flash and 154 kB of on-chip SRAM, 16 kB of
EEPROM memory, a quad SPI Flash Interface (SPIFI), advanced configurable
peripherals such as the SCTimer/PWM and the Serial General Purpose I/O (SGPIO)
interface, two High-speed USB controllers, Ethernet, LCD, an external memory controller,
and multiple digital and analog peripherals. The LPC436x operate at CPU frequencies of
up to 204 MHz.
The ARM Cortex-M4 is a 32-bit core that offers system enhancements such as low power
consumption, enhanced debug features, and a high level of support block integration. The
ARM Cortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture with
separate local instruction and data buses as well as a third bus for peripherals, and
includes an internal prefetch unit that supports speculative branching. The ARM
Cortex-M4 supports single-cycle digital signal processing and SIMD instructions. A
hardware floating-point processor is integrated into the core.
The LPC436x include an application ARM Cortex-M0 coprocessor and a second ARM
Cortex-M0 subsystem for managing the SGPIO and SPI peripherals.The ARM Cortex-M0
coprocessor is an energy-efficient and easy-to-use 32-bit core which is upward code- and
tool-compatible with the Cortex-M4 core. The Cortex-M0 coprocessor, designed as a
replacement for existing 8/16-bit microcontrollers, offers up to 204 MHz performance with
a simple instruction set and reduced code size. In LPC436x, the Cortex-M0 coprocessor
hardware multiply is implemented as a 32-cycle iterative multiplier.
For additional documentation related to the LPC43xx parts, see Section 17.
2. Features and benefits
Cortex-M4 Processor core
ARM Cortex-M4 processor (version r0p1), running at frequencies of up to
204 MHz.
Built-in Memory Protection Unit (MPU) supporting eight regions.
Built-in Nested Vectored Interrupt Controller (NVIC).
Hardware floating-point unit.
Non-maskable Interrupt (NMI) input.
JTAG and Serial Wire Debug (SWD), serial trace, eight breakpoints, and four watch
points.
Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support.
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
LPC436X
Product data sheet
System tick timer.
Cortex-M0 Processor core
ARM Cortex-M0 co-processor (version r0p0) capable of off-loading the main ARM
Cortex-M4 application processor.
Running at frequencies of up to 204 MHz.
JTAG
Built-in NVIC.
Cortex-M0 subsystem
ARM Cortex-M0 coprocessor controlling the SPI and SGPIO residing on a
separate AHB multilayer matrix. Includes 2 kB + 16 kB of SRAM.
Running at frequencies of up to 204 MHz.
Connected via a core-to-core bridge to the main AHB multilayer matrix and the
main ARM Cortex-M4 processor.
JTAG and built-in NVIC.
On-chip memory
Up to 1 MB on-chip dual bank flash memory with flash accelerator.
16 kB on-chip EEPROM data memory.
154 kB SRAM for code and data use.
Multiple SRAM blocks with separate bus access. Two SRAM blocks can be
powered down individually.
64 kB ROM containing boot code and on-chip software drivers.
64 bit+ 256 bit of One-Time Programmable (OTP) memory for general-purpose
use.
Configurable digital peripherals
Serial GPIO (SGPIO) interface.
SCTimer/PWM subsystem on AHB.
Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs and
outputs to event driven peripherals like the timers, SCTimer/PWM, and ADC0/1.
Serial interfaces
Quad SPI Flash Interface (SPIFI) with four lanes and up to 52 MB per second.
10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high
throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time
stamping (IEEE 1588-2008 v2).
One High-speed USB 2.0 Host/Device/OTG interface with DMA support and
on-chip high-speed PHY.
One High-speed USB 2.0 Host/Device interface with DMA support, on-chip
full-speed PHY and ULPI interface to external high-speed PHY.
USB interface electrical test software included in ROM USB stack.
One 550 UART with DMA support and full modem interface.
Three 550 USARTs with DMA and synchronous mode support and a smart card
interface conforming to ISO7816 specification. One USART with IrDA interface.
Up to two C_CAN 2.0B controllers with one channel each.
Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA
support.
One SPI controller.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
2 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
LPC436X
Product data sheet
One Fast-mode Plus I2C-bus interface with monitor mode and with open-drain I/O
pins conforming to the full I2C-bus specification. Supports data rates of up to
1 Mbit/s.
One standard I2C-bus interface with monitor mode and with standard I/O pins.
Two I2S interfaces, each with DMA support and with one input and one output.
Digital peripherals
External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash,
and SDRAM devices.
LCD controller with DMA support and a programmable display resolution of up to
1024 H 768 V. Supports monochrome and color STN panels and TFT color
panels; supports 1/2/4/8 bpp Color Look-Up Table (CLUT) and 16/24-bit direct pixel
mapping. Available on parts LPC4357/53 only.
Secure Digital Input Output (SD/MMC) card interface.
Eight-channel General-Purpose DMA controller can access all memories on the
AHB and all DMA-capable AHB slaves.
Up to 164 General-Purpose Input/Output (GPIO) pins with configurable
pull-up/pull-down resistors.
GPIO registers are located on the AHB for fast access. GPIO ports have DMA
support.
Up to eight GPIO pins can be selected from all GPIO pins as edge and level
sensitive interrupt sources.
Two GPIO group interrupt modules enable an interrupt based on a programmable
pattern of input states of a group of GPIO pins.
Four general-purpose timer/counters with capture and match capabilities.
One motor control Pulse Width Modulator (PWM) for three-phase motor control.
One Quadrature Encoder Interface (QEI).
Repetitive Interrupt timer (RI timer).
Windowed watchdog timer (WWDT).
Ultra-low power Real-Time Clock (RTC) on separate power domain with 256 bytes
of battery powered backup registers.
Alarm timer; can be battery powered.
Analog peripherals
One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s.
Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s.
Up to eight input channels per ADC.
Unique ID for each device.
Clock generation unit
Crystal oscillator with an operating range of 1 MHz to 25 MHz.
12 MHz internal RC oscillator trimmed to 3 % accuracy over temperature and
voltage (1.5 % accuracy for Tamb = 0 °C to 85 °C).
Ultra-low power Real-Time Clock (RTC) crystal oscillator.
Three PLLs allow CPU operation up to the maximum CPU rate without the need for
a high-frequency crystal. The second PLL can be used with the High-speed USB,
the third PLL can be used as audio PLL.
Clock output.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
3 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Power
Single 3.3 V (2.4 V to 3.6 V) power supply with on-chip DC-to-DC converter for the
core supply and the RTC power domain.
RTC power domain can be powered separately by a 3 V battery supply.
Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep
power-down.
Processor wake-up from Sleep mode via wake-up interrupts from various
peripherals.
Wake-up from Deep-sleep, Power-down, and Deep power-down modes via
external interrupts and interrupts generated by battery powered blocks in the RTC
power domain.
Brownout detect with four separate thresholds for interrupt and forced reset.
Power-On Reset (POR).
Available as LQFP208, LBGA256, or TFBGA100 packages.
3. Applications
LPC436X
Product data sheet
Industrial HMI
Secure IoT Gateways
Industrial automation
Industrial control
Consumer health devices
Communication hubs
Embedded audio applications
Automotive aftermarket
White goods
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
4 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
4. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
LPC4367JET256
LBGA256
Plastic low profile ball grid array package; 256 balls; body 17 17 1 mm
SOT740-2
LPC4367JBD208
LQFP208
Plastic low profile quad flat package; 208 leads; body 28 28 1.4 mm
SOT459-1
LPC4367JET100
TFBGA100 Plastic thin fine-pitch ball grid array package; 100 balls; body 9 9 0.7 mm
SOT926-1
4.1 Ordering options
GPIO
Temperature range[1]
ADC channels
QEI
PWM
USB1 (Host, Device)/
ULPI interface
USB0 (Host, Device, OTG)
Ethernet
LCD
Total SRAM
Flash bank B
Flash total
Flash bank A
Ordering options
Type number
Table 2.
LPC4367JET256
1 MB
512 kB
512 kB
154 kB
yes
yes
yes
yes/yes yes
yes
8
J
164
LPC4367JBD208
1 MB
512 kB
512 kB
154 kB
yes
yes
yes
yes/yes yes
yes
8
J
142
LPC4367JET100
1 MB
512 kB
512 kB
154 kB
no
yes
yes
yes/no
yes
4
J
49
[1]
yes
J = -40 °C to +105 °C; F = -40 °C to +85 °C.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
5 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
5. Block diagram
LPC436x
slaves
SUBSYSTEM AHB MULTILAYER MATRIX
system
bus
masters
2 kB LOCAL SRAM
16 kB LOCAL SRAM
ARM
CORTEX-M0
SUBSYSTEM
SPI
SGPIO
TEST/DEBUG
INTERFACE
CORE-CORE
BRIDGE
TEST/DEBUG
INTERFACE
TEST/DEBUG
INTERFACE
ARM
CORTEX-M0
APPLICATION
HIGH-SPEED PHY
ARM
CORTEX-M4
HIGH-SPEED
USB0
HOST/
DEVICE/OTG
HIGH-SPEED
USB1
HOST/DEVICE
SD/
MMC
LCD
system bus
system bus
D-code bus
I-code bus
ETHERNET
10/100
MAC
IEEE 1588
GPDMA
masters
slaves
MAIN AHB MULTILAYER MATRIX
64 kB ROM
slaves
BRIDGE 0
BRIDGE 1
BRIDGE 2
BRIDGE 3
BRIDGE
BRIDGE
32 kB LOCAL SRAM
40 kB LOCAL SRAM
32 kB AHB SRAM
RI TIMER
I2C1
CGU
ALARM TIMER
USART0
MOTOR
CONTROL
PWM
USART2
10-bit DAC
CCU1
BACKUP REGISTERS
UART1
I2C0
USART3
C_CAN0
CCU2
POWER MODE CONTROL
SSP0
I2S0
TIMER2
10-bit ADC0
RGU
TIMER0
I2S1
CONFIGURATION
REGISTERS
TIMER3
10-bit ADC1
TIMER1
C_CAN1
WWDT
16 kB +
16 kB AHB SRAM
16 kB EEPROM
512 kB FLASH A
512 kB FLASH B
EVENT ROUTER
SCU
GPIO
INTERRUPTS
OTP MEMORY
EMC
QEI
RTC
RTC OSC
GIMA
12 MHz IRC
GPIO GROUP0
INTERRUPT
GPIO GROUP1
INTERRUPT
SCT
SSP1
HS GPIO
SPIFI
RTC POWER DOMAIN
= connected to GPDMA
aaa-018614
Fig 1.
LPC436x Block diagram
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
6 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
6. Pinning information
6.1 Pinning
LPC436xJET256
ball A1
index area
2
1
4
3
6
5
8
7
10
9
12
11
14
13
ball A1
index area
16
LPC436xJET100
1
15
A
2
3
4
5
6
7
8
A
B
C
B
E
C
D
F
D
G
E
H
J
F
L
G
K
M
H
N
J
P
R
K
T
aaa-018951
aaa-018950
Transparent top view
Transparent top view
Fig 3.
Pin configuration TFBGA100 package
105
Pin configuration LBGA256 package
156
Fig 2.
9 10
157
104
LPC436xJBD208
Fig 4.
52
53
1
208
aaa-018952
Pin configuration LQFP208 package
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
7 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
6.2 Pin description
On the LPC436x, digital pins are grouped into 16 ports, named P0 to P9 and PA to PF,
with up to 20 pins used per port. Each digital pin can support up to eight different digital
functions, including General Purpose I/O (GPIO), selectable through the System
Configuration Unit (SCU) registers. The pin name is not indicative of the GPIO port
assigned to it.
The parts contain two 10-bit ADCs (ADC0 and ADC1). The input channels of ADC0 and
ADC1 on dedicated pins and multiplexed pins are combined in such a way that all channel
0 inputs (named ADC0_0 and ADC1_0) are tied together and connected to both, channel
0 on ADC0 and channel 0 on ADC1, channel 1 inputs (named ADC0_1 and ADC1_1) are
tied together and connected to channel 1 on ADC0 and ADC1, and so forth. There are
eight ADC channels total for the two ADCs.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
8 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Type
47
Description
[1]
G2
Reset state
LQFP208
Pin name
TFBGA100
Pin description
LBGA256
Table 3.
Multiplexed digital pins
P0_0
P0_1
L3
M2
G1
50
[2]
[2]
N;
PU
N;
PU
I/O
GPIO0[0] — General purpose digital input/output pin.
I/O
SSP1_MISO — Master In Slave Out for SSP1.
I
ENET_RXD1 — Ethernet receive data 1 (RMII/MII interface).
I/O
SGPIO0 — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
I2S0_TX_WS — Transmit Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
I/O
I2S1_TX_WS — Transmit Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
I/O
GPIO0[1] — General purpose digital input/output pin.
I/O
SSP1_MOSI — Master Out Slave in for SSP1.
I
ENET_COL — Ethernet Collision detect (MII interface).
I/O
SGPIO1 — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
ENET_TX_EN — Ethernet transmit enable (RMII/MII
interface).
P1_0
LPC436X
Product data sheet
P2
H1
54
[2]
N;
PU
I/O
I2S1_TX_SDA — I2S1 transmit data. It is driven by the
transmitter and read by the receiver. Corresponds to the signal
SD in the I2S-bus specification.
I/O
GPIO0[4] — General purpose digital input/output pin.
I
CTIN_3 — SCT input 3. Capture input 1 of timer 1.
I/O
EMC_A5 — External memory address line 5.
-
R — Function reserved.
-
R — Function reserved.
I/O
SSP0_SSEL — Slave Select for SSP0.
I/O
SGPIO7 — General purpose digital input/output pin.
I/O
EMC_D12 — External memory data line 12.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
9 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P1_1
P1_2
P1_3
P1_4
LPC436X
Product data sheet
58
R3
P5
T3
K1
J1
J2
60
61
64
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
K2
Description
[1]
R2
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO0[8] — General purpose digital input/output pin. Boot pin
(see Table 5).
O
CTOUT_7 — SCT output 7. Match output 3 of timer 1.
I/O
EMC_A6 — External memory address line 6.
I/O
SGPIO8 — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SSP0_MISO — Master In Slave Out for SSP0.
-
R — Function reserved.
I/O
EMC_D13 — External memory data line 13.
I/O
GPIO0[9] — General purpose digital input/output pin. Boot pin
(see Table 5).
O
CTOUT_6 — SCT output 6. Match output 2 of timer 1.
I/O
EMC_A7 — External memory address line 7.
I/O
SGPIO9 — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SSP0_MOSI — Master Out Slave in for SSP0.
-
R — Function reserved.
I/O
EMC_D14 — External memory data line 14.
I/O
GPIO0[10] — General purpose digital input/output pin.
O
CTOUT_8 — SCT output 8. Match output 0 of timer 2.
I/O
SGPIO10 — General purpose digital input/output pin.
O
EMC_OE — LOW active Output Enable signal.
O
USB0_IND1 — USB0 port indicator LED control
output 1.
I/O
SSP1_MISO — Master In Slave Out for SSP1.
-
R — Function reserved.
O
SD_RST — SD/MMC reset signal for MMC4.4 card.
I/O
GPIO0[11] — General purpose digital input/output pin.
O
CTOUT_9 — SCT output 9. Match output 3 of timer 3.
I/O
SGPIO11 — General purpose digital input/output pin.
O
EMC_BLS0 — LOW active Byte Lane select signal 0.
O
USB0_IND0 — USB0 port indicator LED control output 0.
I/O
SSP1_MOSI — Master Out Slave in for SSP1.
I/O
EMC_D15 — External memory data line 15.
O
SD_VOLT1 — SD/MMC bus voltage select output 1.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
10 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P1_5
P1_6
P1_7
65
T4
T5
K4
G4
67
69
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
Type
J4
Description
[1]
R5
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO1[8] — General purpose digital input/output pin.
O
CTOUT_10 — SCT output 10. Match output 3 of timer 3.
-
R — Function reserved.
O
EMC_CS0 — LOW active Chip Select 0 signal.
I
USB0_PWR_FAULT — Port power fault signal indicating
overcurrent condition; this signal monitors over-current on the
USB bus (external circuitry required to detect over-current
condition).
I/O
SSP1_SSEL — Slave Select for SSP1.
I/O
SGPIO15 — General purpose digital input/output pin.
O
SD_POW — SD/MMC power monitor output.
I/O
GPIO1[9] — General purpose digital input/output pin.
I
CTIN_5 — SCT input 5. Capture input 2 of timer 2.
-
R — Function reserved.
O
EMC_WE — LOW active Write Enable signal.
-
R — Function reserved.
O
EMC_BLS0 — LOW active Byte Lane select signal 0.
I/O
SGPIO14 — General purpose digital input/output pin.
I/O
SD_CMD — SD/MMC command signal.
I/O
GPIO1[0] — General purpose digital input/output pin.
I
U1_DSR — Data Set Ready input for UART1.
O
CTOUT_13 — SCT output 13. Match output 3 of timer 3.
I/O
EMC_D0 — External memory data line 0.
O
USB0_PPWR — VBUS drive signal (towards external charge
pump or power management unit); indicates that VBUS must
be driven (active HIGH).
Add a pull-down resistor to disable the power switch at reset.
This signal has opposite polarity compared to the USB_PPWR
used on other NXP LPC parts.
LPC436X
Product data sheet
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
11 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P1_8
P1_9
P1_10
P1_11
LPC436X
Product data sheet
71
T7
R8
T9
J5
H6
J7
73
75
77
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
H5
Description
[1]
R7
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO1[1] — General purpose digital input/output pin.
O
U1_DTR — Data Terminal Ready output for UART1.
O
CTOUT_12 — SCT output 12. Match output 3 of
timer 3.
I/O
EMC_D1 — External memory data line 1.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
SD_VOLT0 — SD/MMC bus voltage select output 0.
I/O
GPIO1[2] — General purpose digital input/output pin.
O
U1_RTS — Request to Send output for UART1.
O
CTOUT_11 — SCT output 11. Match output 3 of timer 2.
I/O
EMC_D2 — External memory data line 2.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
SD_DAT0 — SD/MMC data bus line 0.
I/O
GPIO1[3] — General purpose digital input/output pin.
I
U1_RI — Ring Indicator input for UART1.
O
CTOUT_14 — SCT output 14. Match output 2 of timer 3.
I/O
EMC_D3 — External memory data line 3.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
SD_DAT1 — SD/MMC data bus line 1.
I/O
GPIO1[4] — General purpose digital input/output pin.
I
U1_CTS — Clear to Send input for UART1.
O
CTOUT_15 — SCT output 15. Match output 3 of timer 3.
I/O
EMC_D4 — External memory data line 4.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
SD_DAT2 — SD/MMC data bus line 2.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
12 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P1_12
P1_13
P1_14
P1_15
LPC436X
Product data sheet
78
R10
R11
T12
H8
J8
K8
83
85
87
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
K7
Description
[1]
R9
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO1[5] — General purpose digital input/output pin.
I
U1_DCD — Data Carrier Detect input for UART1.
-
R — Function reserved.
I/O
EMC_D5 — External memory data line 5.
I
T0_CAP1 — Capture input 1 of timer 0.
-
R — Function reserved.
I/O
SGPIO8 — General purpose digital input/output pin.
I/O
SD_DAT3 — SD/MMC data bus line 3.
I/O
GPIO1[6] — General purpose digital input/output pin.
O
U1_TXD — Transmitter output for UART1.
-
R — Function reserved.
I/O
EMC_D6 — External memory data line 6.
I
T0_CAP0 — Capture input 0 of timer 0.
-
R — Function reserved.
I/O
SGPIO9 — General purpose digital input/output pin.
I
SD_CD — SD/MMC card detect input.
I/O
GPIO1[7] — General purpose digital input/output pin.
I
U1_RXD — Receiver input for UART1.
-
R — Function reserved.
I/O
EMC_D7 — External memory data line 7.
O
T0_MAT2 — Match output 2 of timer 0.
-
R — Function reserved.
I/O
SGPIO10 — General purpose digital input/output pin.
-
R — Function reserved.
I/O
GPIO0[2] — General purpose digital input/output pin.
O
U2_TXD — Transmitter output for USART2.
I/O
SGPIO2 — General purpose digital input/output pin.
I
ENET_RXD0 — Ethernet receive data 0 (RMII/MII interface).
O
T0_MAT1 — Match output 1 of timer 0.
-
R — Function reserved.
I/O
EMC_D8 — External memory data line 8.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
13 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P1_16
P1_17
P1_18
P1_19
LPC436X
Product data sheet
90
M8
N12
M11
H10
J10
K9
93
95
96
[2]
[3]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
H9
Description
[1]
M7
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO0[3] — General purpose digital input/output pin.
I
U2_RXD — Receiver input for USART2.
I/O
SGPIO3 — General purpose digital input/output pin.
I
ENET_CRS — Ethernet Carrier Sense (MII interface).
O
T0_MAT0 — Match output 0 of timer 0.
-
R — Function reserved.
I/O
EMC_D9 — External memory data line 9.
I
ENET_RX_DV — Ethernet Receive Data Valid (RMII/MII
interface).
I/O
GPIO0[12] — General purpose digital input/output pin.
I/O
U2_UCLK — Serial clock input/output for USART2 in
synchronous mode.
-
R — Function reserved.
I/O
ENET_MDIO — Ethernet MIIM data input and output.
I
T0_CAP3 — Capture input 3 of timer 0.
O
CAN1_TD — CAN1 transmitter output.
I/O
SGPIO11 — General purpose digital input/output pin.
-
R — Function reserved.
I/O
GPIO0[13] — General purpose digital input/output pin.
I/O
U2_DIR — RS-485/EIA-485 output enable/direction control for
USART2.
-
R — Function reserved.
O
ENET_TXD0 — Ethernet transmit data 0 (RMII/MII interface).
O
T0_MAT3 — Match output 3 of timer 0.
I
CAN1_RD — CAN1 receiver input.
I/O
SGPIO12 — General purpose digital input/output pin.
I/O
EMC_D10 — External memory data line 10.
I
ENET_TX_CLK (ENET_REF_CLK) — Ethernet Transmit
Clock (MII interface) or Ethernet Reference Clock (RMII
interface).
I/O
SSP1_SCK — Serial clock for SSP1.
-
R — Function reserved.
-
R — Function reserved.
O
CLKOUT — Clock output pin.
-
R — Function reserved.
O
I2S0_RX_MCLK — I2S receive master clock.
I/O
I2S1_TX_SCK — Transmit Clock. It is driven by the master
and received by the slave. Corresponds to the signal SCK in
the I2S-bus specification.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
14 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P1_20
P2_0
100
T16
G10
108
[2]
[2]
N;
PU
N;
PU
Type
K10
Description
[1]
M10
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO0[15] — General purpose digital input/output pin.
I/O
SSP1_SSEL — Slave Select for SSP1.
-
R — Function reserved.
O
ENET_TXD1 — Ethernet transmit data 1 (RMII/MII interface).
I
T0_CAP2 — Capture input 2 of timer 0.
-
R — Function reserved.
I/O
SGPIO13 — General purpose digital input/output pin.
I/O
EMC_D11 — External memory data line 11.
I/O
SGPIO4 — General purpose digital input/output pin.
O
U0_TXD — Transmitter output for USART0. See Table 4 for
ISP mode.
I/O
EMC_A13 — External memory address line 13.
O
USB0_PPWR — VBUS drive signal (towards external charge
pump or power management unit); indicates that VBUS must
be driven (active HIGH).
Add a pull-down resistor to disable the power switch at reset.
This signal has opposite polarity compared to the USB_PPWR
used on other NXP LPC parts.
P2_1
LPC436X
Product data sheet
N15
G7
116
[2]
N;
PU
I/O
GPIO5[0] — General purpose digital input/output pin.
-
R — Function reserved.
I
T3_CAP0 — Capture input 0 of timer 3.
O
ENET_MDC — Ethernet MIIM clock.
I/O
SGPIO5 — General purpose digital input/output pin.
I
U0_RXD — Receiver input for USART0. See Table 4 for ISP
mode.
I/O
EMC_A12 — External memory address line 12.
I
USB0_PWR_FAULT — Port power fault signal indicating
overcurrent condition; this signal monitors over-current on the
USB bus (external circuitry required to detect over-current
condition).
I/O
GPIO5[1] — General purpose digital input/output pin.
-
R — Function reserved.
I
T3_CAP1 — Capture input 1 of timer 3.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
15 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P2_2
P2_3
121
J12
D8
127
[2]
[3]
N;
PU
N;
PU
Type
F5
Description
[1]
M15
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
SGPIO6 — General purpose digital input/output pin.
I/O
U0_UCLK — Serial clock input/output for USART0 in
synchronous mode.
I/O
EMC_A11 — External memory address line 11.
O
USB0_IND1 — USB0 port indicator LED control output 1.
I/O
GPIO5[2] — General purpose digital input/output pin.
I
CTIN_6 — SCT input 6. Capture input 1 of timer 3.
I
T3_CAP2 — Capture input 2 of timer 3.
O
EMC_CS1 — LOW active Chip Select 1 signal.
I/O
SGPIO12 — General purpose digital input/output pin.
I/O
I2C1_SDA — I2C1 data input/output (this pin does not use a
specialized I2C pad).
O
U3_TXD — Transmitter output for USART3. See Table 4 for
ISP mode.
I
CTIN_1 — SCT input 1. Capture input 1 of timer 0. Capture
input 1 of timer 2.
I/O
GPIO5[3] — General purpose digital input/output pin.
-
R — Function reserved.
O
T3_MAT0 — Match output 0 of timer 3.
O
USB0_PPWR — VBUS drive signal (towards external charge
pump or power management unit); indicates that VBUS must
be driven (active HIGH).
Add a pull-down resistor to disable the power switch at reset.
This signal has opposite polarity compared to the USB_PPWR
used on other NXP LPC parts.
P2_4
LPC436X
Product data sheet
K11
D9
128
[3]
N;
PU
I/O
SGPIO13 — General purpose digital input/output pin.
I/O
I2C1_SCL — I2C1 clock input/output (this pin does not use a
specialized I2C pad).
I
U3_RXD — Receiver input for USART3. See Table 4 for ISP
mode.
I
CTIN_0 — SCT input 0. Capture input 0 of timer 0, 1, 2, 3.
I/O
GPIO5[4] — General purpose digital input/output pin.
-
R — Function reserved.
O
T3_MAT1 — Match output 1 of timer 3.
I
USB0_PWR_FAULT — Port power fault signal indicating
overcurrent condition; this signal monitors over-current on the
USB bus (external circuitry required to detect over-current
condition).
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
16 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P2_5
131
[3]
N;
PU
Type
D10
Description
[1]
K14
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
SGPIO14 — General purpose digital input/output pin.
I
CTIN_2 — SCT input 2. Capture input 2 of timer 0.
I
USB1_VBUS — Monitors the presence of USB1 bus power.
Note: This signal must be HIGH for USB reset to occur.
P2_6
P2_7
P2_8
LPC436X
Product data sheet
K16
H14
J16
G9
C10
C6
137
138
140
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
I
ADCTRIG1 — ADC trigger input 1.
I/O
GPIO5[5] — General purpose digital input/output pin.
-
R — Function reserved.
O
T3_MAT2 — Match output 2 of timer 3.
O
USB0_IND0 — USB0 port indicator LED control output 0.
I/O
SGPIO7 — General purpose digital input/output pin.
I/O
U0_DIR — RS-485/EIA-485 output enable/direction control for
USART0.
I/O
EMC_A10 — External memory address line 10.
O
USB0_IND0 — USB0 port indicator LED control
output 0.
I/O
GPIO5[6] — General purpose digital input/output pin.
I
CTIN_7 — SCT input 7.
I
T3_CAP3 — Capture input 3 of timer 3.
O
EMC_BLS1 — LOW active Byte Lane select signal 1.
I/O
GPIO0[7] — General purpose digital input/output pin. If this
pin is pulled LOW at reset, the part enters ISP mode or boots
from an external source (see Table 4 and Table 5).
O
CTOUT_1 — SCT output 1. Match output 3 of timer 3.
I/O
U3_UCLK — Serial clock input/output for USART3 in
synchronous mode.
I/O
EMC_A9 — External memory address line 9.
-
R — Function reserved.
-
R — Function reserved.
O
T3_MAT3 — Match output 3 of timer 3.
-
R — Function reserved.
I/O
SGPIO15 — General purpose digital input/output pin. Boot pin
(see Table 5).
O
CTOUT_0 — SCT output 0. Match output 0 of timer 0.
I/O
U3_DIR — RS-485/EIA-485 output enable/direction control for
USART3.
I/O
EMC_A8 — External memory address line 8.
I/O
GPIO5[7] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
17 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P2_9
P2_10
P2_11
P2_12
LPC436X
Product data sheet
144
G16
F16
E15
E8
A9
B9
146
148
153
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
B10
Description
[1]
H16
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO1[10] — General purpose digital input/output pin. Boot
pin (see Table 5).
O
CTOUT_3 — SCT output 3. Match output 3 of timer 0.
I/O
U3_BAUD — Baud pin for USART3.
I/O
EMC_A0 — External memory address line 0.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO0[14] — General purpose digital input/output pin.
O
CTOUT_2 — SCT output 2. Match output 2 of timer 0.
O
U2_TXD — Transmitter output for USART2.
I/O
EMC_A1 — External memory address line 1.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO1[11] — General purpose digital input/output pin.
O
CTOUT_5 — SCT output 5. Match output 3 of timer 3.
I
U2_RXD — Receiver input for USART2.
I/O
EMC_A2 — External memory address line 2.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO1[12] — General purpose digital input/output pin.
O
CTOUT_4 — SCT output 4. Match output 3 of timer 3.
-
R — Function reserved.
I/O
EMC_A3 — External memory address line 3.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
U2_UCLK — Serial clock input/output for USART2 in
synchronous mode.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
18 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P2_13
P3_0
P3_1
LPC436X
Product data sheet
156
F13
G11
A8
F7
161
163
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
Type
A10
Description
[1]
C16
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO1[13] — General purpose digital input/output pin.
I
CTIN_4 — SCT input 4. Capture input 2 of timer 1.
-
R — Function reserved.
I/O
EMC_A4 — External memory address line 4.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
U2_DIR — RS-485/EIA-485 output enable/direction control for
USART2.
I/O
I2S0_RX_SCK — I2S receive clock. It is driven by the master
and received by the slave. Corresponds to the signal SCK in
the I2S-bus specification.
O
I2S0_RX_MCLK — I2S receive master clock.
I/O
I2S0_TX_SCK — Transmit Clock. It is driven by the master
and received by the slave. Corresponds to the signal SCK in
the I2S-bus specification.
O
I2S0_TX_MCLK — I2S transmit master clock.
I/O
SSP0_SCK — Serial clock for SSP0.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
I2S0_TX_WS — Transmit Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
I/O
I2S0_RX_WS — Receive Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
I
CAN0_RD — CAN receiver input.
O
USB1_IND1 — USB1 Port indicator LED control output 1.
I/O
GPIO5[8] — General purpose digital input/output pin.
-
R — Function reserved.
O
LCD_VD15 — LCD data.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
19 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P3_2
P3_3
P3_4
LPC436X
Product data sheet
166
B14
A15
A7
B8
169
171
[2]
[4]
[2]
OL;
PU
N;
PU
N;
PU
Type
G6
Description
[1]
F11
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
I2S0_TX_SDA — I2S transmit data. It is driven by the
transmitter and read by the receiver. Corresponds to the signal
SD in the I2S-bus specification.
I/O
I2S0_RX_SDA — I2S Receive data. It is driven by the
transmitter and read by the receiver. Corresponds to the signal
SD in the I2S-bus specification.
O
CAN0_TD — CAN transmitter output.
O
USB1_IND0 — USB1 Port indicator LED control output 0.
I/O
GPIO5[9] — General purpose digital input/output pin.
-
R — Function reserved.
O
LCD_VD14 — LCD data.
-
R — Function reserved.
-
R — Function reserved.
I/O
SPI_SCK — Serial clock for SPI.
I/O
SSP0_SCK — Serial clock for SSP0.
O
SPIFI_SCK — Serial clock for SPIFI.
O
CGU_OUT1 — CGU spare clock output 1.
-
R — Function reserved.
O
I2S0_TX_MCLK — I2S transmit master clock.
I/O
I2S1_TX_SCK — Transmit Clock. It is driven by the master
and received by the slave. Corresponds to the signal SCK in
the I2S-bus specification.
I/O
GPIO1[14] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SPIFI_SIO3 — I/O lane 3 for SPIFI.
O
U1_TXD — Transmitter output for UART 1.
I/O
I2S0_TX_WS — Transmit Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
I/O
I2S1_RX_SDA — I2S1 Receive data. It is driven by the
transmitter and read by the receiver. Corresponds to the signal
SD in the I2S-bus specification.
O
LCD_VD13 — LCD data.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
20 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P3_5
P3_6
P3_7
P3_8
LPC436X
Product data sheet
173
B13
C11
C10
C7
D7
E7
174
176
179
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
B7
Description
[1]
C12
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO1[15] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SPIFI_SIO2 — I/O lane 2 for SPIFI.
I
U1_RXD — Receiver input for UART 1.
I/O
I2S0_TX_SDA — I2S transmit data. It is driven by the
transmitter and read by the receiver. Corresponds to the signal
SD in the I2S-bus specification.
I/O
I2S1_RX_WS — Receive Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
O
LCD_VD12 — LCD data.
I/O
GPIO0[6] — General purpose digital input/output pin.
I/O
SPI_MISO — Master In Slave Out for SPI.
I/O
SSP0_SSEL — Slave Select for SSP0.
I/O
SPIFI_MISO — Input 1 in SPIFI quad mode; SPIFI output IO1.
-
R — Function reserved.
I/O
SSP0_MISO — Master In Slave Out for SSP0.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
SPI_MOSI — Master Out Slave In for SPI.
I/O
SSP0_MISO — Master In Slave Out for SSP0.
I/O
SPIFI_MOSI — Input I0 in SPIFI quad mode; SPIFI output
IO0.
I/O
GPIO5[10] — General purpose digital input/output pin.
I/O
SSP0_MOSI — Master Out Slave in for SSP0.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I
SPI_SSEL — Slave Select for SPI. Note that this pin in an
input pin only. The SPI in master mode cannot drive the CS
input on the slave. Any GPIO pin can be used for SPI chip
select in master mode.
I/O
SSP0_MOSI — Master Out Slave in for SSP0.
I/O
SPIFI_CS — SPIFI serial flash chip select.
I/O
GPIO5[11] — General purpose digital input/output pin.
I/O
SSP0_SSEL — Slave Select for SSP0.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
21 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P4_0
P4_1
P4_2
P4_3
LPC436X
Product data sheet
1
A1
D3
C2
-
-
-
3
12
10
[2]
[5]
[2]
[5]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
D5
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO2[0] — General purpose digital input/output pin.
O
MCOA0 — Motor control PWM channel 0, output A.
I
NMI — External interrupt input to NMI.
-
R — Function reserved.
-
R — Function reserved.
O
LCD_VD13 — LCD data.
I/O
U3_UCLK — Serial clock input/output for USART3 in
synchronous mode.
-
R — Function reserved.
I/O
GPIO2[1] — General purpose digital input/output pin.
O
CTOUT_1 — SCT output 1. Match output 3 of timer 3.
O
LCD_VD0 — LCD data.
-
R — Function reserved.
-
R — Function reserved.
O
LCD_VD19 — LCD data.
O
U3_TXD — Transmitter output for USART3.
I
ENET_COL — Ethernet Collision detect (MII interface).
AI
ADC0_1 — ADC0 and ADC1, input channel 1. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
I/O
GPIO2[2] — General purpose digital input/output pin.
O
CTOUT_0 — SCT output 0. Match output 0 of timer 0.
O
LCD_VD3 — LCD data.
-
R — Function reserved.
-
R — Function reserved.
O
LCD_VD12 — LCD data.
I
U3_RXD — Receiver input for USART3.
I/O
SGPIO8 — General purpose digital input/output pin.
I/O
GPIO2[3] — General purpose digital input/output pin.
O
CTOUT_3 — SCT output 3. Match output 3 of timer 0.
O
LCD_VD2 — LCD data.
-
R — Function reserved.
-
R — Function reserved.
O
LCD_VD21 — LCD data.
I/O
U3_BAUD — Baud pin for USART3.
I/O
SGPIO9 — General purpose digital input/output pin.
AI
ADC0_0 — DAC, ADC0 and ADC1, input channel 0.
Configure the pin as GPIO input and use the ADC function
select register in the SCU to select the ADC.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
22 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P4_4
P4_5
P4_6
LPC436X
Product data sheet
14
D2
C1
-
-
15
17
[5]
[2]
[2]
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
B1
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO2[4] — General purpose digital input/output pin.
O
CTOUT_2 — SCT output 2. Match output 2 of timer 0.
O
LCD_VD1 — LCD data.
-
R — Function reserved.
-
R — Function reserved.
O
LCD_VD20 — LCD data.
I/O
U3_DIR — RS-485/EIA-485 output enable/direction control for
USART3.
I/O
SGPIO10 — General purpose digital input/output pin.
O
DAC — DAC output. Configure the pin as GPIO input and use
the analog function select register in the SCU to select the
DAC.
I/O
GPIO2[5] — General purpose digital input/output pin.
O
CTOUT_5 — SCT output 5. Match output 3 of timer 3.
O
LCD_FP — Frame pulse (STN). Vertical synchronization
pulse (TFT).
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO11 — General purpose digital input/output pin.
I/O
GPIO2[6] — General purpose digital input/output pin.
O
CTOUT_4 — SCT output 4. Match output 3 of timer 3.
O
LCD_ENAB/LCDM — STN AC bias drive or TFT data enable
input.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO12 — General purpose digital input/output pin.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
23 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P4_7
P4_8
P4_9
P4_10
LPC436X
Product data sheet
21
E2
L2
M3
-
-
-
23
48
51
[2]
[2]
[2]
[2]
O;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
H4
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
O
LCD_DCLK — LCD panel clock.
I
GP_CLKIN — General purpose clock input to the CGU.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
I2S1_TX_SCK — Transmit Clock. It is driven by the master
and received by the slave. Corresponds to the signal SCK in
the I2S-bus specification.
I/O
I2S0_TX_SCK — Transmit Clock. It is driven by the master
and received by the slave. Corresponds to the signal SCK in
the I2S-bus specification.
-
R — Function reserved.
I
CTIN_5 — SCT input 5. Capture input 2 of timer 2.
O
LCD_VD9 — LCD data.
-
R — Function reserved.
I/O
GPIO5[12] — General purpose digital input/output pin.
O
LCD_VD22 — LCD data.
O
CAN1_TD — CAN1 transmitter output.
I/O
SGPIO13 — General purpose digital input/output pin.
-
R — Function reserved.
I
CTIN_6 — SCT input 6. Capture input 1 of timer 3.
O
LCD_VD11 — LCD data.
-
R — Function reserved.
I/O
GPIO5[13] — General purpose digital input/output pin.
O
LCD_VD15 — LCD data.
I
CAN1_RD — CAN1 receiver input.
I/O
SGPIO14 — General purpose digital input/output pin.
-
R — Function reserved.
I
CTIN_2 — SCT input 2. Capture input 2 of timer 0.
O
LCD_VD10 — LCD data.
-
R — Function reserved.
I/O
GPIO5[14] — General purpose digital input/output pin.
O
LCD_VD14 — LCD data.
-
R — Function reserved.
I/O
SGPIO15 — General purpose digital input/output pin.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
24 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P5_0
P5_1
P5_2
P5_3
LPC436X
Product data sheet
53
P3
R4
T8
-
-
-
55
63
76
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
N3
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO2[9] — General purpose digital input/output pin.
O
MCOB2 — Motor control PWM channel 2, output B.
I/O
EMC_D12 — External memory data line 12.
-
R — Function reserved.
I
U1_DSR — Data Set Ready input for UART 1.
I
T1_CAP0 — Capture input 0 of timer 1.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO2[10] — General purpose digital input/output pin.
I
MCI2 — Motor control PWM channel 2, input.
I/O
EMC_D13 — External memory data line 13.
-
R — Function reserved.
O
U1_DTR — Data Terminal Ready output for UART 1. Can also
be configured to be an RS-485/EIA-485 output enable signal
for UART 1.
I
T1_CAP1 — Capture input 1 of timer 1.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO2[11] — General purpose digital input/output pin.
I
MCI1 — Motor control PWM channel 1, input.
I/O
EMC_D14 — External memory data line 14.
-
R — Function reserved.
O
U1_RTS — Request to Send output for UART 1. Can also be
configured to be an RS-485/EIA-485 output enable signal for
UART 1.
I
T1_CAP2 — Capture input 2 of timer 1.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO2[12] — General purpose digital input/output pin.
I
MCI0 — Motor control PWM channel 0, input.
I/O
EMC_D15 — External memory data line 15.
-
R — Function reserved.
I
U1_RI — Ring Indicator input for UART 1.
I
T1_CAP3 — Capture input 3 of timer 1.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
25 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P5_4
P5_5
P5_6
P5_7
LPC436X
Product data sheet
80
P10
T13
R12
-
-
-
81
89
91
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
P9
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO2[13] — General purpose digital input/output pin.
O
MCOB0 — Motor control PWM channel 0, output B.
I/O
EMC_D8 — External memory data line 8.
-
R — Function reserved.
I
U1_CTS — Clear to Send input for UART 1.
O
T1_MAT0 — Match output 0 of timer 1.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO2[14] — General purpose digital input/output pin.
O
MCOA1 — Motor control PWM channel 1, output A.
I/O
EMC_D9 — External memory data line 9.
-
R — Function reserved.
I
U1_DCD — Data Carrier Detect input for UART 1.
O
T1_MAT1 — Match output 1 of timer 1.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO2[15] — General purpose digital input/output pin.
O
MCOB1 — Motor control PWM channel 1, output B.
I/O
EMC_D10 — External memory data line 10.
-
R — Function reserved.
O
U1_TXD — Transmitter output for UART 1.
O
T1_MAT2 — Match output 2 of timer 1.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO2[7] — General purpose digital input/output pin.
O
MCOA2 — Motor control PWM channel 2, output A.
I/O
EMC_D11 — External memory data line 11.
-
R — Function reserved.
I
U1_RXD — Receiver input for UART 1.
O
T1_MAT3 — Match output 3 of timer 1.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
26 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P6_0
P6_1
P6_2
LPC436X
Product data sheet
105
R15
L13
G5
J9
107
111
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
Type
H7
Description
[1]
M12
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
O
I2S0_RX_MCLK — I2S receive master clock.
-
R — Function reserved.
-
R — Function reserved.
I/O
I2S0_RX_SCK — Receive Clock. It is driven by the master
and received by the slave. Corresponds to the signal SCK in
the I2S-bus specification.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO3[0] — General purpose digital input/output pin.
O
EMC_DYCS1 — SDRAM chip select 1.
I/O
U0_UCLK — Serial clock input/output for USART0 in
synchronous mode.
I/O
I2S0_RX_WS — Receive Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
-
R — Function reserved.
I
T2_CAP0 — Capture input 2 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO3[1] — General purpose digital input/output pin.
O
EMC_CKEOUT1 — SDRAM clock enable 1.
I/O
U0_DIR — RS-485/EIA-485 output enable/direction control for
USART0.
I/O
I2S0_RX_SDA — I2S Receive data. It is driven by the
transmitter and read by the receiver. Corresponds to the signal
SD in the I2S-bus specification.
-
R — Function reserved.
I
T2_CAP1 — Capture input 1 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
27 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P6_3
113
[2]
N;
PU
Type
-
Description
[1]
P15
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO3[2] — General purpose digital input/output pin.
O
USB0_PPWR — VBUS drive signal (towards external charge
pump or power management unit); indicates that the VBUS
signal must be driven (active HIGH).
Add a pull-down resistor to disable the power switch at reset.
This signal has opposite polarity compared to the USB_PPWR
used on other NXP LPC parts.
P6_4
P6_5
P6_6
LPC436X
Product data sheet
R16
P16
L14
F6
F9
-
114
117
119
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
I/O
SGPIO4 — General purpose digital input/output pin.
O
EMC_CS1 — LOW active Chip Select 1 signal.
-
R — Function reserved.
I
T2_CAP2 — Capture input 2 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO3[3] — General purpose digital input/output pin.
I
CTIN_6 — SCT input 6. Capture input 1 of timer 3.
O
U0_TXD — Transmitter output for USART0.
O
EMC_CAS — LOW active SDRAM Column Address Strobe.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO3[4] — General purpose digital input/output pin.
O
CTOUT_6 — SCT output 6. Match output 2 of timer 1.
I
U0_RXD — Receiver input for USART0.
O
EMC_RAS — LOW active SDRAM Row Address Strobe.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO0[5] — General purpose digital input/output pin.
O
EMC_BLS1 — LOW active Byte Lane select signal 1.
I/O
SGPIO5 — General purpose digital input/output pin.
I
USB0_PWR_FAULT — Port power fault signal indicating
overcurrent condition; this signal monitors over-current on the
USB bus (external circuitry required to detect over-current
condition).
-
R — Function reserved.
I
T2_CAP3 — Capture input 3 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
28 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P6_7
P6_8
P6_9
P6_10
LPC436X
Product data sheet
123
H13
J15
H15
-
F8
-
125
139
142
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
J13
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
I/O
EMC_A15 — External memory address line 15.
I/O
SGPIO6 — General purpose digital input/output pin.
O
USB0_IND1 — USB0 port indicator LED control output 1.
I/O
GPIO5[15] — General purpose digital input/output pin.
O
T2_MAT0 — Match output 0 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
EMC_A14 — External memory address line 14.
I/O
SGPIO7 — General purpose digital input/output pin.
O
USB0_IND0 — USB0 port indicator LED control output 0.
I/O
GPIO5[16] — General purpose digital input/output pin.
O
T2_MAT1 — Match output 1 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO3[5] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
O
EMC_DYCS0 — SDRAM chip select 0.
-
R — Function reserved.
O
T2_MAT2 — Match output 2 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO3[6] — General purpose digital input/output pin.
O
MCABORT — Motor control PWM, LOW-active fast abort.
-
R — Function reserved.
O
EMC_DQMOUT1 — Data mask 1 used with SDRAM and
static devices.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
29 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P6_11
P6_12
P7_0
P7_1
LPC436X
Product data sheet
143
G15
B16
C14
-
-
-
145
158
162
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
C9
Description
[1]
H12
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO3[7] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
O
EMC_CKEOUT0 — SDRAM clock enable 0.
-
R — Function reserved.
O
T2_MAT3 — Match output 3 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO2[8] — General purpose digital input/output pin.
O
CTOUT_7 — SCT output 7. Match output 3 of timer 1.
-
R — Function reserved.
O
EMC_DQMOUT0 — Data mask 0 used with SDRAM and
static devices.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO3[8] — General purpose digital input/output pin.
O
CTOUT_14 — SCT output 14. Match output 2 of timer 3.
-
R — Function reserved.
O
LCD_LE — Line end signal.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO4 — General purpose digital input/output pin.
I/O
GPIO3[9] — General purpose digital input/output pin.
O
CTOUT_15 — SCT output 15. Match output 3 of timer 3.
I/O
I2S0_TX_WS — Transmit Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
O
LCD_VD19 — LCD data.
O
LCD_VD7 — LCD data.
-
R — Function reserved.
O
U2_TXD — Transmitter output for USART2.
I/O
SGPIO5 — General purpose digital input/output pin.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
30 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P7_2
P7_3
P7_4
P7_5
LPC436X
Product data sheet
165
C13
C8
A7
-
-
-
167
189
191
[2]
[2]
[5]
[5]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
A16
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO3[10] — General purpose digital input/output pin.
I
CTIN_4 — SCT input 4. Capture input 2 of timer 1.
I/O
I2S0_TX_SDA — I2S transmit data. It is driven by the
transmitter and read by the receiver. Corresponds to the signal
SD in the I2S-bus specification.
O
LCD_VD18 — LCD data.
O
LCD_VD6 — LCD data.
-
R — Function reserved.
I
U2_RXD — Receiver input for USART2.
I/O
SGPIO6 — General purpose digital input/output pin.
I/O
GPIO3[11] — General purpose digital input/output pin.
I
CTIN_3 — SCT input 3. Capture input 1 of timer 1.
-
R — Function reserved.
O
LCD_VD17 — LCD data.
O
LCD_VD5 — LCD data.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO3[12] — General purpose digital input/output pin.
O
CTOUT_13 — SCT output 13. Match output 3 of timer 3.
-
R — Function reserved.
O
LCD_VD16 — LCD data.
O
LCD_VD4 — LCD data.
O
TRACEDATA[0] — Trace data, bit 0.
-
R — Function reserved.
-
R — Function reserved.
AI
ADC0_4 — ADC0 and ADC1, input channel 4. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
I/O
GPIO3[13] — General purpose digital input/output pin.
O
CTOUT_12 — SCT output 12. Match output 3 of timer 3.
-
R — Function reserved.
O
LCD_VD8 — LCD data.
O
LCD_VD23 — LCD data.
O
TRACEDATA[1] — Trace data, bit 1.
-
R — Function reserved.
-
R — Function reserved.
AI
ADC0_3 — ADC0 and ADC1, input channel 3. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
31 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P7_6
P7_7
P8_0
P8_1
LPC436X
Product data sheet
194
B6
E5
H5
-
-
-
201
2
34
[2]
[5]
[3]
[3]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
C7
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO3[14] — General purpose digital input/output pin.
O
CTOUT_11 — SCT output 1. Match output 3 of timer 2.
-
R — Function reserved.
O
LCD_LP — Line synchronization pulse (STN). Horizontal
synchronization pulse (TFT).
-
R — Function reserved.
O
TRACEDATA[2] — Trace data, bit 2.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO3[15] — General purpose digital input/output pin.
O
CTOUT_8 — SCT output 8. Match output 0 of timer 2.
-
R — Function reserved.
O
LCD_PWR — LCD panel power enable.
-
R — Function reserved.
O
TRACEDATA[3] — Trace data, bit 3.
O
ENET_MDC — Ethernet MIIM clock.
I/O
SGPIO7 — General purpose digital input/output pin.
AI
ADC1_6 — ADC1 and ADC0, input channel 6. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
I/O
GPIO4[0] — General purpose digital input/output pin.
I
USB0_PWR_FAULT — Port power fault signal indicating
overcurrent condition; this signal monitors over-current on the
USB bus (external circuitry required to detect over-current
condition).
-
R — Function reserved.
I
MCI2 — Motor control PWM channel 2, input.
I/O
SGPIO8 — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
O
T0_MAT0 — Match output 0 of timer 0.
I/O
GPIO4[1] — General purpose digital input/output pin.
O
USB0_IND1 — USB0 port indicator LED control output 1.
-
R — Function reserved.
I
MCI1 — Motor control PWM channel 1, input.
I/O
SGPIO9 — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
O
T0_MAT1 — Match output 1 of timer 0.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
32 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P8_2
P8_3
P8_4
P8_5
LPC436X
Product data sheet
36
J3
J2
J1
-
-
-
37
39
40
[3]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
K4
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO4[2] — General purpose digital input/output pin.
O
USB0_IND0 — USB0 port indicator LED control output 0.
-
R — Function reserved.
I
MCI0 — Motor control PWM channel 0, input.
I/O
SGPIO10 — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
O
T0_MAT2 — Match output 2 of timer 0.
I/O
GPIO4[3] — General purpose digital input/output pin.
I/O
USB1_ULPI_D2 — ULPI link bidirectional data line 2.
-
R — Function reserved.
O
LCD_VD12 — LCD data.
O
LCD_VD19 — LCD data.
-
R — Function reserved.
-
R — Function reserved.
O
T0_MAT3 — Match output 3 of timer 0.
I/O
GPIO4[4] — General purpose digital input/output pin.
I/O
USB1_ULPI_D1 — ULPI link bidirectional data line 1.
-
R — Function reserved.
O
LCD_VD7 — LCD data.
O
LCD_VD16 — LCD data.
-
R — Function reserved.
-
R — Function reserved.
I
T0_CAP0 — Capture input 0 of timer 0.
I/O
GPIO4[5] — General purpose digital input/output pin.
I/O
USB1_ULPI_D0 — ULPI link bidirectional data line 0.
-
R — Function reserved.
O
LCD_VD6 — LCD data.
O
LCD_VD8 — LCD data.
-
R — Function reserved.
-
R — Function reserved.
I
T0_CAP1 — Capture input 1 of timer 0.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
33 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P8_6
P8_7
P8_8
P9_0
LPC436X
Product data sheet
43
K1
L1
T1
-
-
-
45
49
59
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
K3
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO4[6] — General purpose digital input/output pin.
I
USB1_ULPI_NXT — ULPI link NXT signal. Data flow control
signal from the PHY.
-
R — Function reserved.
O
LCD_VD5 — LCD data.
O
LCD_LP — Line synchronization pulse (STN). Horizontal
synchronization pulse (TFT).
-
R — Function reserved.
-
R — Function reserved.
I
T0_CAP2 — Capture input 2 of timer 0.
I/O
GPIO4[7] — General purpose digital input/output pin.
O
USB1_ULPI_STP — ULPI link STP signal. Asserted to end or
interrupt transfers to the PHY.
-
R — Function reserved.
O
LCD_VD4 — LCD data.
O
LCD_PWR — LCD panel power enable.
-
R — Function reserved.
-
R — Function reserved.
I
T0_CAP3 — Capture input 3 of timer 0.
-
R — Function reserved.
I
USB1_ULPI_CLK — ULPI link CLK signal. 60 MHz clock
generated by the PHY.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CGU_OUT0 — CGU spare clock output 0.
O
I2S1_TX_MCLK — I2S1 transmit master clock.
I/O
GPIO4[12] — General purpose digital input/output pin.
O
MCABORT — Motor control PWM, LOW-active fast abort.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I
ENET_CRS — Ethernet Carrier Sense (MII interface).
I/O
SGPIO0 — General purpose digital input/output pin.
I/O
SSP0_SSEL — Slave Select for SSP0.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
34 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P9_1
P9_2
P9_3
P9_4
LPC436X
Product data sheet
66
N8
M6
N10
-
-
-
70
79
92
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
N6
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO4[13] — General purpose digital input/output pin.
O
MCOA2 — Motor control PWM channel 2, output A.
-
R — Function reserved.
-
R — Function reserved.
I/O
I2S0_TX_WS — Transmit Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
I
ENET_RX_ER — Ethernet receive error (MII interface).
I/O
SGPIO1 — General purpose digital input/output pin.
I/O
SSP0_MISO — Master In Slave Out for SSP0.
I/O
GPIO4[14] — General purpose digital input/output pin.
O
MCOB2 — Motor control PWM channel 2, output B.
-
R — Function reserved.
-
R — Function reserved.
I/O
I2S0_TX_SDA — I2S transmit data. It is driven by the
transmitter and read by the receiver. Corresponds to the signal
SD in the I2S-bus specification.
I
ENET_RXD3 — Ethernet receive data 3 (MII interface).
I/O
SGPIO2 — General purpose digital input/output pin.
I/O
SSP0_MOSI — Master Out Slave in for SSP0.
I/O
GPIO4[15] — General purpose digital input/output pin.
O
MCOA0 — Motor control PWM channel 0, output A.
O
USB1_IND1 — USB1 Port indicator LED control output 1.
-
R — Function reserved.
-
R — Function reserved.
I
ENET_RXD2 — Ethernet receive data 2 (MII interface).
I/O
SGPIO9 — General purpose digital input/output pin.
O
U3_TXD — Transmitter output for USART3.
-
R — Function reserved.
O
MCOB0 — Motor control PWM channel 0, output B.
O
USB1_IND0 — USB1 Port indicator LED control output 0.
-
R — Function reserved.
I/O
GPIO5[17] — General purpose digital input/output pin.
O
ENET_TXD2 — Ethernet transmit data 2 (MII interface).
I/O
SGPIO4 — General purpose digital input/output pin.
I
U3_RXD — Receiver input for USART3.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
35 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
P9_5
98
[2]
N;
PU
Type
-
Description
[1]
M9
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
O
MCOA1 — Motor control PWM channel 1, output A.
O
USB1_PPWR — VBUS drive signal (towards external charge
pump or power management unit); indicates that VBUS must
be driven (active high).
Add a pull-down resistor to disable the power switch at reset.
This signal has opposite polarity compared to the USB_PPWR
used on other NXP LPC parts.
P9_6
PA_0
PA_1
LPC436X
Product data sheet
L11
L12
J14
-
-
-
103
126
134
[2]
[2]
[3]
N;
PU
N;
PU
N;
PU
-
R — Function reserved.
I/O
GPIO5[18] — General purpose digital input/output pin.
O
ENET_TXD3 — Ethernet transmit data 3 (MII interface).
I/O
SGPIO3 — General purpose digital input/output pin.
O
U0_TXD — Transmitter output for USART0.
I/O
GPIO4[11] — General purpose digital input/output pin.
O
MCOB1 — Motor control PWM channel 1, output B.
I
USB1_PWR_FAULT — USB1 Port power fault signal
indicating over-current condition; this signal monitors
over-current on the USB1 bus (external circuitry required to
detect over-current condition).
-
R — Function reserved.
-
R — Function reserved.
I
ENET_COL — Ethernet Collision detect (MII interface).
I/O
SGPIO8 — General purpose digital input/output pin.
I
U0_RXD — Receiver input for USART0.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
I2S1_RX_MCLK — I2S1 receive master clock.
O
CGU_OUT1 — CGU spare clock output 1.
-
R — Function reserved.
I/O
GPIO4[8] — General purpose digital input/output pin.
I
QEI_IDX — Quadrature Encoder Interface INDEX input.
-
R — Function reserved.
O
U2_TXD — Transmitter output for USART2.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
36 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PA_2
PA_3
PA_4
PB_0
LPC436X
Product data sheet
136
H11
G13
B15
-
-
-
147
151
164
[3]
[3]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
K15
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
GPIO4[9] — General purpose digital input/output pin.
I
QEI_PHB — Quadrature Encoder Interface PHB input.
-
R — Function reserved.
I
U2_RXD — Receiver input for USART2.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO4[10] — General purpose digital input/output pin.
I
QEI_PHA — Quadrature Encoder Interface PHA input.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CTOUT_9 — SCT output 9. Match output 3 of timer 3.
-
R — Function reserved.
I/O
EMC_A23 — External memory address line 23.
I/O
GPIO5[19] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CTOUT_10 — SCT output 10. Match output 3 of timer 3.
O
LCD_VD23 — LCD data.
-
R — Function reserved.
I/O
GPIO5[20] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
37 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PB_1
PB_2
PB_3
PB_4
LPC436X
Product data sheet
175
B12
A13
B11
-
-
-
177
178
180
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
A14
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
I
USB1_ULPI_DIR — ULPI link DIR signal. Controls the ULP
data line direction.
O
LCD_VD22 — LCD data.
-
R — Function reserved.
I/O
GPIO5[21] — General purpose digital input/output pin.
O
CTOUT_6 — SCT output 6. Match output 2 of timer 1.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
USB1_ULPI_D7 — ULPI link bidirectional data line 7.
O
LCD_VD21 — LCD data.
-
R — Function reserved.
I/O
GPIO5[22] — General purpose digital input/output pin.
O
CTOUT_7 — SCT output 7. Match output 3 of timer 1.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
USB1_ULPI_D6 — ULPI link bidirectional data line 6.
O
LCD_VD20 — LCD data.
-
R — Function reserved.
I/O
GPIO5[23] — General purpose digital input/output pin.
O
CTOUT_8 — SCT output 8. Match output 0 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
USB1_ULPI_D5 — ULPI link bidirectional data line 5.
O
LCD_VD15 — LCD data.
-
R — Function reserved.
I/O
GPIO5[24] — General purpose digital input/output pin.
I
CTIN_5 — SCT input 5. Capture input 2 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
38 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PB_5
PB_6
PC_0
PC_1
LPC436X
Product data sheet
181
A6
D4
E4
-
-
-
-
7
9
[2]
[5]
[5]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
A12
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
I/O
USB1_ULPI_D4 — ULPI link bidirectional data line 4.
O
LCD_VD14 — LCD data.
-
R — Function reserved.
I/O
GPIO5[25] — General purpose digital input/output pin.
I
CTIN_7 — SCT input 7.
O
LCD_PWR — LCD panel power enable.
-
R — Function reserved.
-
R — Function reserved.
I/O
USB1_ULPI_D3 — ULPI link bidirectional data line 3.
O
LCD_VD13 — LCD data.
-
R — Function reserved.
I/O
GPIO5[26] — General purpose digital input/output pin.
I
CTIN_6 — SCT input 6. Capture input 1 of timer 3.
O
LCD_VD19 — LCD data.
-
R — Function reserved.
AI
ADC0_6 — ADC0 and ADC1, input channel 6. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
-
R — Function reserved.
I
USB1_ULPI_CLK — ULPI link CLK signal. 60 MHz clock
generated by the PHY.
-
R — Function reserved.
I/O
ENET_RX_CLK — Ethernet Receive Clock (MII interface).
O
LCD_DCLK — LCD panel clock.
-
R — Function reserved.
-
R — Function reserved.
I/O
SD_CLK — SD/MMC card clock.
AI
ADC1_1 — ADC1 and ADC0, input channel 1. Configure the
pin as input (USB_ULPI_CLK) and use the ADC function
select register in the SCU to select the ADC.
I/O
USB1_ULPI_D7 — ULPI link bidirectional data line 7.
-
R — Function reserved.
I
U1_RI — Ring Indicator input for UART 1.
O
ENET_MDC — Ethernet MIIM clock.
I/O
GPIO6[0] — General purpose digital input/output pin.
-
R — Function reserved.
I
T3_CAP0 — Capture input 0 of timer 3.
O
SD_VOLT0 — SD/MMC bus voltage select output 0.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
39 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PC_2
PC_3
PC_4
13
F5
F4
-
-
11
16
[2]
[5]
[2]
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
F6
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I/O
USB1_ULPI_D6 — ULPI link bidirectional data line 6.
-
R — Function reserved.
I
U1_CTS — Clear to Send input for UART 1.
O
ENET_TXD2 — Ethernet transmit data 2 (MII interface).
I/O
GPIO6[1] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
O
SD_RST — SD/MMC reset signal for MMC4.4 card.
I/O
USB1_ULPI_D5 — ULPI link bidirectional data line 5.
-
R — Function reserved.
O
U1_RTS — Request to Send output for UART 1. Can also be
configured to be an RS-485/EIA-485 output enable signal for
UART 1.
O
ENET_TXD3 — Ethernet transmit data 3 (MII interface).
I/O
GPIO6[2] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
O
SD_VOLT1 — SD/MMC bus voltage select output 1.
AI
ADC1_0 — DAC, ADC1 and ADC0, input channel 0.
Configure the pin as GPIO input and use the ADC function
select register in the SCU to select the ADC.
-
R — Function reserved.
I/O
USB1_ULPI_D4 — ULPI link bidirectional data line 4.
-
R — Function reserved.
ENET_TX_EN — Ethernet transmit enable (RMII/MII
interface).
PC_5
LPC436X
Product data sheet
G4
-
20
[2]
N;
PU
I/O
GPIO6[3] — General purpose digital input/output pin.
-
R — Function reserved.
I
T3_CAP1 — Capture input 1 of timer 3.
I/O
SD_DAT0 — SD/MMC data bus line 0.
-
R — Function reserved.
I/O
USB1_ULPI_D3 — ULPI link bidirectional data line 3.
-
R — Function reserved.
O
ENET_TX_ER — Ethernet Transmit Error (MII interface).
I/O
GPIO6[4] — General purpose digital input/output pin.
-
R — Function reserved.
I
T3_CAP2 — Capture input 2 of timer 3.
I/O
SD_DAT1 — SD/MMC data bus line 1.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
40 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PC_6
PC_7
PC_8
PC_9
LPC436X
Product data sheet
22
G5
N4
K2
-
-
-
-
-
-
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
H6
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
I/O
USB1_ULPI_D2 — ULPI link bidirectional data line 2.
-
R — Function reserved.
I
ENET_RXD2 — Ethernet receive data 2 (MII interface).
I/O
GPIO6[5] — General purpose digital input/output pin.
-
R — Function reserved.
I
T3_CAP3 — Capture input 3 of timer 3.
I/O
SD_DAT2 — SD/MMC data bus line 2.
-
R — Function reserved.
I/O
USB1_ULPI_D1 — ULPI link bidirectional data line 1.
-
R — Function reserved.
I
ENET_RXD3 — Ethernet receive data 3 (MII interface).
I/O
GPIO6[6] — General purpose digital input/output pin.
-
R — Function reserved.
O
T3_MAT0 — Match output 0 of timer 3.
I/O
SD_DAT3 — SD/MMC data bus line 3.
-
R — Function reserved.
I/O
USB1_ULPI_D0 — ULPI link bidirectional data line 0.
-
R — Function reserved.
I
ENET_RX_DV — Ethernet Receive Data Valid (RMII/MII
interface).
I/O
GPIO6[7] — General purpose digital input/output pin.
-
R — Function reserved.
O
T3_MAT1 — Match output 1 of timer 3.
I
SD_CD — SD/MMC card detect input.
-
R — Function reserved.
I
USB1_ULPI_NXT — ULPI link NXT signal. Data flow control
signal from the PHY.
-
R — Function reserved.
I
ENET_RX_ER — Ethernet receive error (MII interface).
I/O
GPIO6[8] — General purpose digital input/output pin.
-
R — Function reserved.
O
T3_MAT2 — Match output 2 of timer 3.
O
SD_POW — SD/MMC power monitor output.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
41 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PC_10
PC_11
PC_12
PC_13
LPC436X
Product data sheet
-
L5
L6
M1
-
-
-
-
-
-
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
M5
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
O
USB1_ULPI_STP — ULPI link STP signal. Asserted to end or
interrupt transfers to the PHY.
I
U1_DSR — Data Set Ready input for UART 1.
-
R — Function reserved.
I/O
GPIO6[9] — General purpose digital input/output pin.
-
R — Function reserved.
O
T3_MAT3 — Match output 3 of timer 3.
I/O
SD_CMD — SD/MMC command signal.
-
R — Function reserved.
I
USB1_ULPI_DIR — ULPI link DIR signal. Controls the ULPI
data line direction.
I
U1_DCD — Data Carrier Detect input for UART 1.
-
R — Function reserved.
I/O
GPIO6[10] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SD_DAT4 — SD/MMC data bus line 4.
-
R — Function reserved.
-
R — Function reserved.
O
U1_DTR — Data Terminal Ready output for UART 1. Can also
be configured to be an RS-485/EIA-485 output enable signal
for UART 1.
-
R — Function reserved.
I/O
GPIO6[11] — General purpose digital input/output pin.
I/O
SGPIO11 — General purpose digital input/output pin.
I/O
I2S0_TX_SDA — I2S transmit data. It is driven by the
transmitter and read by the receiver. Corresponds to the signal
SD in the I2S-bus specification.
I/O
SD_DAT5 — SD/MMC data bus line 5.
-
R — Function reserved.
-
R — Function reserved.
O
U1_TXD — Transmitter output for UART 1.
-
R — Function reserved.
I/O
GPIO6[12] — General purpose digital input/output pin.
I/O
SGPIO12 — General purpose digital input/output pin.
I/O
I2S0_TX_WS — Transmit Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
I/O
SD_DAT6 — SD/MMC data bus line 6.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
42 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PC_14
PD_0
PD_1
PD_2
LPC436X
Product data sheet
-
N2
P1
R1
-
-
-
-
-
-
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
N1
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
-
R — Function reserved.
I
U1_RXD — Receiver input for UART 1.
-
R — Function reserved.
I/O
GPIO6[13] — General purpose digital input/output pin.
I/O
SGPIO13 — General purpose digital input/output pin.
O
ENET_TX_ER — Ethernet Transmit Error (MII interface).
I/O
SD_DAT7 — SD/MMC data bus line 7.
-
R — Function reserved.
O
CTOUT_15 — SCT output 15. Match output 3 of timer 3.
O
EMC_DQMOUT2 — Data mask 2 used with SDRAM and
static devices.
-
R — Function reserved.
I/O
GPIO6[14] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO4 — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
O
EMC_CKEOUT2 — SDRAM clock enable 2.
-
R — Function reserved.
I/O
GPIO6[15] — General purpose digital input/output pin.
O
SD_POW — SD/MMC power monitor output.
-
R — Function reserved.
I/O
SGPIO5 — General purpose digital input/output pin.
-
R — Function reserved.
O
CTOUT_7 — SCT output 7. Match output 3 of timer 1.
I/O
EMC_D16 — External memory data line 16.
-
R — Function reserved.
I/O
GPIO6[16] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO6 — General purpose digital input/output pin.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
43 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PD_3
PD_4
PD_5
PD_6
LPC436X
Product data sheet
-
T2
P6
R6
-
-
-
-
-
68
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
P4
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
O
CTOUT_6 — SCT output 7. Match output 2 of timer 1.
I/O
EMC_D17 — External memory data line 17.
-
R — Function reserved.
I/O
GPIO6[17] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO7 — General purpose digital input/output pin.
-
R — Function reserved.
O
CTOUT_8 — SCT output 8. Match output 0 of timer 2.
I/O
EMC_D18 — External memory data line 18.
-
R — Function reserved.
I/O
GPIO6[18] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO8 — General purpose digital input/output pin.
-
R — Function reserved.
O
CTOUT_9 — SCT output 9. Match output 3 of timer 3.
I/O
EMC_D19 — External memory data line 19.
-
R — Function reserved.
I/O
GPIO6[19] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO9 — General purpose digital input/output pin.
-
R — Function reserved.
O
CTOUT_10 — SCT output 10. Match output 3 of timer 3.
I/O
EMC_D20 — External memory data line 20.
-
R — Function reserved.
I/O
GPIO6[20] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO10 — General purpose digital input/output pin.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
44 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PD_7
PD_8
PD_9
PD_10
LPC436X
Product data sheet
72
P8
T11
P11
-
-
-
74
84
86
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
T6
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
I
CTIN_5 — SCT input 5. Capture input 2 of timer 2.
I/O
EMC_D21 — External memory data line 21.
-
R — Function reserved.
I/O
GPIO6[21] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO11 — General purpose digital input/output pin.
-
R — Function reserved.
I
CTIN_6 — SCT input 6. Capture input 1 of timer 3.
I/O
EMC_D22 — External memory data line 22.
-
R — Function reserved.
I/O
GPIO6[22] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO12 — General purpose digital input/output pin.
-
R — Function reserved.
O
CTOUT_13 — SCT output 13. Match output 3 of timer 3.
I/O
EMC_D23 — External memory data line 23.
-
R — Function reserved.
I/O
GPIO6[23] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SGPIO13 — General purpose digital input/output pin.
-
R — Function reserved.
I
CTIN_1 — SCT input 1. Capture input 1 of timer 0. Capture
input 1 of timer 2.
O
EMC_BLS3 — LOW active Byte Lane select signal 3.
-
R — Function reserved.
I/O
GPIO6[24] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
45 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PD_11
PD_12
PD_13
PD_14
LPC436X
Product data sheet
88
N11
T14
R13
-
-
-
94
97
99
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
N9
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
-
R — Function reserved.
O
EMC_CS3 — LOW active Chip Select 3 signal.
-
R — Function reserved.
I/O
GPIO6[25] — General purpose digital input/output pin.
I/O
USB1_ULPI_D0 — ULPI link bidirectional data line 0.
O
CTOUT_14 — SCT output 14. Match output 2 of timer 3.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
EMC_CS2 — LOW active Chip Select 2 signal.
-
R — Function reserved.
I/O
GPIO6[26] — General purpose digital input/output pin.
-
R — Function reserved.
O
CTOUT_10 — SCT output 10. Match output 3 of timer 3.
-
R — Function reserved.
-
R — Function reserved.
I
CTIN_0 — SCT input 0. Capture input 0 of timer 0, 1, 2, 3.
O
EMC_BLS2 — LOW active Byte Lane select signal 2.
-
R — Function reserved.
I/O
GPIO6[27] — General purpose digital input/output pin.
-
R — Function reserved.
O
CTOUT_13 — SCT output 13. Match output 3 of timer 3.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
EMC_DYCS2 — SDRAM chip select 2.
-
R — Function reserved.
I/O
GPIO6[28] — General purpose digital input/output pin.
-
R — Function reserved.
O
CTOUT_11 — SCT output 11. Match output 3 of timer 2.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
46 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PD_15
PD_16
PE_0
PE_1
LPC436X
Product data sheet
101
R14
P14
N14
-
-
-
104
106
112
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
T15
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
-
R — Function reserved.
I/O
EMC_A17 — External memory address line 17.
-
R — Function reserved.
I/O
GPIO6[29] — General purpose digital input/output pin.
I
SD_WP — SD/MMC card write protect input.
O
CTOUT_8 — SCT output 8. Match output 0 of timer 2.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
EMC_A16 — External memory address line 16.
-
R — Function reserved.
I/O
GPIO6[30] — General purpose digital input/output pin.
O
SD_VOLT2 — SD/MMC bus voltage select output 2.
O
CTOUT_12 — SCT output 12. Match output 3 of timer 3.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
EMC_A18 — External memory address line 18.
I/O
GPIO7[0] — General purpose digital input/output pin.
O
CAN1_TD — CAN1 transmitter output.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
EMC_A19 — External memory address line 19.
I/O
GPIO7[1] — General purpose digital input/output pin.
I
CAN1_RD — CAN1 receiver input.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
47 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PE_2
PE_3
PE_4
PE_5
LPC436X
Product data sheet
115
K12
K13
N16
-
-
-
118
120
122
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
M14
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I
ADCTRIG0 — ADC trigger input 0.
I
CAN0_RD — CAN receiver input.
-
R — Function reserved.
I/O
EMC_A20 — External memory address line 20.
I/O
GPIO7[2] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CAN0_TD — CAN transmitter output.
I
ADCTRIG1 — ADC trigger input 1.
I/O
EMC_A21 — External memory address line 21.
I/O
GPIO7[3] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I
NMI — External interrupt input to NMI.
-
R — Function reserved.
I/O
EMC_A22 — External memory address line 22.
I/O
GPIO7[4] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CTOUT_3 — SCT output 3. Match output 3 of timer 0.
O
U1_RTS — Request to Send output for UART 1. Can also be
configured to be an RS-485/EIA-485 output enable signal for
UART 1.
I/O
EMC_D24 — External memory data line 24.
I/O
GPIO7[5] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
48 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PE_6
PE_7
PE_8
PE_9
LPC436X
Product data sheet
124
F15
F14
E16
-
-
-
149
150
152
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
M16
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
O
CTOUT_2 — SCT output 2. Match output 2 of timer 0.
I
U1_RI — Ring Indicator input for UART 1.
I/O
EMC_D25 — External memory data line 25.
I/O
GPIO7[6] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CTOUT_5 — SCT output 5. Match output 3 of timer 3.
I
U1_CTS — Clear to Send input for UART1.
I/O
EMC_D26 — External memory data line 26.
I/O
GPIO7[7] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CTOUT_4 — SCT output 4. Match output 3 of timer 3.
I
U1_DSR — Data Set Ready input for UART 1.
I/O
EMC_D27 — External memory data line 27.
I/O
GPIO7[8] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I
CTIN_4 — SCT input 4. Capture input 2 of timer 1.
I
U1_DCD — Data Carrier Detect input for UART 1.
I/O
EMC_D28 — External memory data line 28.
I/O
GPIO7[9] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
49 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PE_10
PE_11
PE_12
PE_13
LPC436X
Product data sheet
154
D16
D15
G14
-
-
-
-
-
-
[2]
[2]
[2]
[2]
N;
PU
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
E14
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
I
CTIN_3 — SCT input 3. Capture input 1 of timer 1.
O
U1_DTR — Data Terminal Ready output for UART 1. Can also
be configured to be an RS-485/EIA-485 output enable signal
for UART 1.
I/O
EMC_D29 — External memory data line 29.
I/O
GPIO7[10] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CTOUT_12 — SCT output 12. Match output 3 of timer 3.
O
U1_TXD — Transmitter output for UART 1.
I/O
EMC_D30 — External memory data line 30.
I/O
GPIO7[11] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CTOUT_11 — SCT output 11. Match output 3 of
timer 2.
I
U1_RXD — Receiver input for UART 1.
I/O
EMC_D31 — External memory data line 31.
I/O
GPIO7[12] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CTOUT_14 — SCT output 14. Match output 2 of timer 3.
I/O
I2C1_SDA — I2C1 data input/output (this pin does not use a
specialized I2C pad).
O
EMC_DQMOUT3 — Data mask 3 used with SDRAM and
static devices.
I/O
GPIO7[13] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
50 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PE_14
PE_15
PF_0
PF_1
LPC436X
Product data sheet
-
E13
D12
E11
-
-
-
-
159
-
[2]
[2]
[2]
[2]
N;
PU
N;
PU
O;
PU
N;
PU
Type
-
Description
[1]
C15
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
EMC_DYCS3 — SDRAM chip select 3.
I/O
GPIO7[14] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CTOUT_0 — SCT output 0. Match output 0 of timer 0.
I/O
I2C1_SCL — I2C1 clock input/output (this pin does not use a
specialized I2C pad).
O
EMC_CKEOUT3 — SDRAM clock enable 3.
I/O
GPIO7[15] — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
I/O
SSP0_SCK — Serial clock for SSP0.
I
GP_CLKIN — General purpose clock input to the CGU.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
I2S1_TX_MCLK — I2S1 transmit master clock.
-
R — Function reserved.
-
R — Function reserved.
I/O
SSP0_SSEL — Slave Select for SSP0.
-
R — Function reserved.
I/O
GPIO7[16] — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SGPIO0 — General purpose digital input/output pin.
-
R — Function reserved.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
51 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PF_2
PF_3
PF_4
PF_5
LPC436X
Product data sheet
168
E10
D10
E9
-
H4
-
170
172
190
[2]
[2]
[2]
[5]
N;
PU
N;
PU
O;
PU
N;
PU
Type
-
Description
[1]
D11
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
O
U3_TXD — Transmitter output for USART3.
I/O
SSP0_MISO — Master In Slave Out for SSP0.
-
R — Function reserved.
I/O
GPIO7[17] — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SGPIO1 — General purpose digital input/output pin.
-
R — Function reserved.
-
R — Function reserved.
I
U3_RXD — Receiver input for USART3.
I/O
SSP0_MOSI — Master Out Slave in for SSP0.
-
R — Function reserved.
I/O
GPIO7[18] — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SGPIO2 — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SSP1_SCK — Serial clock for SSP1.
I
GP_CLKIN — General purpose clock input to the CGU.
O
TRACECLK — Trace clock.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
I2S0_TX_MCLK — I2S transmit master clock.
I/O
I2S0_RX_SCK — I2S receive clock. It is driven by the master
and received by the slave. Corresponds to the signal SCK in
the I2S-bus specification.
-
R — Function reserved.
I/O
U3_UCLK — Serial clock input/output for USART3 in
synchronous mode.
I/O
SSP1_SSEL — Slave Select for SSP1.
O
TRACEDATA[0] — Trace data, bit 0.
I/O
GPIO7[19] — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SGPIO4 — General purpose digital input/output pin.
-
R — Function reserved.
AI
ADC1_4 — ADC1 and ADC0, input channel 4. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
52 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PF_6
PF_7
PF_8
LPC436X
Product data sheet
192
B7
E6
-
-
193
-
[5]
[5]
[5]
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
E7
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
I/O
U3_DIR — RS-485/EIA-485 output enable/direction control for
USART3.
I/O
SSP1_MISO — Master In Slave Out for SSP1.
O
TRACEDATA[1] — Trace data, bit 1.
I/O
GPIO7[20] — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SGPIO5 — General purpose digital input/output pin.
I/O
I2S1_TX_SDA — I2S1 transmit data. It is driven by the
transmitter and read by the receiver. Corresponds to the signal
SD in the I2S-bus specification.
AI
ADC1_3 — ADC1 and ADC0, input channel 3. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
-
R — Function reserved.
I/O
U3_BAUD — Baud pin for USART3.
I/O
SSP1_MOSI — Master Out Slave in for SSP1.
O
TRACEDATA[2] — Trace data, bit 2.
I/O
GPIO7[21] — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SGPIO6 — General purpose digital input/output pin.
I/O
I2S1_TX_WS — Transmit Word Select. It is driven by the
master and received by the slave. Corresponds to the signal
WS in the I2S-bus specification.
AI/
O
ADC1_7 — ADC1 and ADC0, input channel 7 or band gap
output. Configure the pin as GPIO input and use the ADC
function select register in the SCU to select the ADC.
-
R — Function reserved.
I/O
U0_UCLK — Serial clock input/output for USART0 in
synchronous mode.
I
CTIN_2 — SCT input 2. Capture input 2 of timer 0.
O
TRACEDATA[3] — Trace data, bit 3.
I/O
GPIO7[22] — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SGPIO7 — General purpose digital input/output pin.
-
R — Function reserved.
AI
ADC0_2 — ADC0 and ADC1, input channel 2. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
53 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
PF_9
PF_10
PF_11
LPC436X
Product data sheet
203
A3
A2
-
-
205
207
[5]
[5]
[5]
N;
PU
N;
PU
N;
PU
Type
-
Description
[1]
D6
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
R — Function reserved.
I/O
U0_DIR — RS-485/EIA-485 output enable/direction control for
USART0.
O
CTOUT_1 — SCT output 1. Match output 3 of timer 3.
-
R — Function reserved.
I/O
GPIO7[23] — General purpose digital input/output pin.
-
R — Function reserved.
I/O
SGPIO3 — General purpose digital input/output pin.
-
R — Function reserved.
AI
ADC1_2 — ADC1 and ADC0, input channel 2. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
-
R — Function reserved.
O
U0_TXD — Transmitter output for USART0.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO7[24] — General purpose digital input/output pin.
-
R — Function reserved.
I
SD_WP — SD/MMC card write protect input.
-
R — Function reserved.
AI
ADC0_5 — ADC0 and ADC1, input channel 5. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
-
R — Function reserved.
I
U0_RXD — Receiver input for USART0.
-
R — Function reserved.
-
R — Function reserved.
I/O
GPIO7[25] — General purpose digital input/output pin.
-
R — Function reserved.
O
SD_VOLT2 — SD/MMC bus voltage select output 2.
-
R — Function reserved.
AI
ADC1_5 — ADC1 and ADC0, input channel 5. Configure the
pin as GPIO input and use the ADC function select register in
the SCU to select the ADC.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
54 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
62
Type
K3
Description
[1]
N5
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
Clock pins
CLK0
CLK1
CLK2
CLK3
LPC436X
Product data sheet
T10
D14
P12
-
K6
-
-
141
-
[4]
[4]
[4]
[4]
O;
PU
O;
PU
O;
PU
O;
PU
O
EMC_CLK0 — SDRAM clock 0.
O
CLKOUT — Clock output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SD_CLK — SD/MMC card clock.
O
EMC_CLK01 — SDRAM clock 0 and clock 1 combined.
I/O
SSP1_SCK — Serial clock for SSP1.
I
ENET_TX_CLK (ENET_REF_CLK) — Ethernet Transmit
Clock (MII interface) or Ethernet Reference Clock (RMII
interface).
O
EMC_CLK1 — SDRAM clock 1.
O
CLKOUT — Clock output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CGU_OUT0 — CGU spare clock output 0.
-
R — Function reserved.
O
I2S1_TX_MCLK — I2S1 transmit master clock.
O
EMC_CLK3 — SDRAM clock 3.
O
CLKOUT — Clock output pin.
-
R — Function reserved.
-
R — Function reserved.
I/O
SD_CLK — SD/MMC card clock.
O
EMC_CLK23 — SDRAM clock 2 and clock 3 combined.
O
I2S0_TX_MCLK — I2S transmit master clock.
I/O
I2S1_RX_SCK — Receive Clock. It is driven by the master
and received by the slave. Corresponds to the signal SCK in
the I2S-bus specification.
O
EMC_CLK2 — SDRAM clock 2.
O
CLKOUT — Clock output pin.
-
R — Function reserved.
-
R — Function reserved.
-
R — Function reserved.
O
CGU_OUT1 — CGU spare clock output 1.
-
R — Function reserved.
I/O
I2S1_RX_SCK — Receive Clock. It is driven by the master
and received by the slave. Corresponds to the signal SCK in
the I2S-bus specification.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
55 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
41
Type
A6
Description
[1]
L4
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
Debug pins
DBGEN
[2]
I
I
JTAG interface control signal. Also used for boundary scan. To
use the part in functional mode, connect this pin in one of the
following ways:
•
Leave DBGEN open. The DBGEN pin is pulled up
internally by a 50 kΩ resistor.
•
•
Tie DBGEN to VDDIO.
Pull DBGEN up to VDDIO with an external pull-up
resistor.
TCK/SWDCLK
J5
H2
38
[2]
I; F
TRST
M4
B4
42
[2]
I; PU I
Test Reset for JTAG interface.
TMS/SWDIO
K6
C4
44
[2]
I; PU I
Test Mode Select for JTAG interface (default) or SW debug
data input/output.
TDO/SWO
K5
H3
46
[2]
O
Test Data Out for JTAG interface (default) or SW trace output.
I; PU I
Test Data In for JTAG interface.
I
O
Test Clock for JTAG interface (default) or Serial Wire (SW)
clock.
J4
G3
35
[2]
USB0_DP
F2
E1
26
[6]
-
I/O
USB0 bidirectional D+ line. Do not add an external series
resistor.
USB0_DM
G2
E2
28
[6]
-
I/O
USB0 bidirectional D line. Do not add an external series
resistor.
USB0_VBUS
F1
E3
29
[6]
-
I
VBUS pin (power on USB cable). This pin includes an internal
pull-down resistor of 64 k (typical) 16 k.
I
Indicates to the transceiver whether connected as an A-device
(USB0_ID LOW) or B-device (USB0_ID HIGH). For OTG this
pin has an internal pull-up resistor.
TDI
USB0 pins
[7]
USB0_ID
H2
F1
30
[8]
-
USB0_RREF
H1
F3
32
[8]
-
USB1_DP
F12
E9
129
[9]
-
I/O
USB1 bidirectional D+ line. Add an external series resistor of
33 +/- 2 %.
USB1_DM
G12
E10
130
[9]
-
I/O
USB1 bidirectional D line. Add an external series resistor of
33 +/- 2 %.
I2C0_SCL
L15
D6
132
[10]
I; F
I/O
I2C clock input/output. Open-drain output (for I2C-bus
compliance).
I2C0_SDA
L16
E6
133
[10]
I; F
I/O
I2C data input/output. Open-drain output (for I2C-bus
compliance).
B6
185
[11]
I; IA
I
External reset input: A LOW on this pin resets the device,
causing I/O ports and peripherals to take on their default
states, and processor execution to begin at address 0. This
pin does not have an internal pull-up.
12.0 k (accuracy 1 %) on-board resistor to ground for current
reference.
USB1 pins
I2C-bus pins
Reset and wake-up pins
RESET
LPC436X
Product data sheet
D9
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
56 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
WAKEUP0
187
[11]
I; IA
Type
A4
Description
[1]
A9
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
I
External wake-up input; can raise an interrupt and can cause
wake-up from any of the low power modes. A pulse with a
duration of at least 45 ns wakes up the part.
Input 0 of the event monitor.No internal pull-up is enabled
when this pin is configured as input.
WAKEUP1
A10
-
-
[11]
I; IA
I
External wake-up input; can raise an interrupt and can cause
wake-up from any of the low power modes. A pulse with a
duration of at least 45 ns wakes up the part.
Input 1 of the event monitor. No internal pull-up is enabled
when this pin is configured as input.
WAKEUP2
C9
-
-
[11]
I; IA
I
External wake-up input; can raise an interrupt and can cause
wake-up from any of the low power modes. A pulse with a
duration of at least 45 ns wakes up the part.
Input 2 of the event monitor. This pin does not have an internal
pull-up.
D8
-
-
[11]
I; IA
I
External wake-up input; can raise an interrupt and can cause
wake-up from any of the low power modes. A pulse with a
duration of at least 45 ns wakes up the part. This pin does not
have an internal pull-up.
ADC0_0/
ADC1_0/DAC
E3
A2
8
[8]
I; IA
I
ADC input channel 0. Shared between 10-bit ADC0/1 and
DAC.
ADC0_1/
ADC1_1
C3
A1
4
[8]
I; IA
I
ADC input channel 1. Shared between 10-bit ADC0/1.
ADC0_2/
ADC1_2
A4
B3
206
[8]
I; IA
I
ADC input channel 2. Shared between 10-bit ADC0/1.
ADC0_3/
ADC1_3
B5
A3
200
[8]
I; IA
I
ADC input channel 3. Shared between 10-bit ADC0/1.
ADC0_4/
ADC1_4
C6
-
199
[8]
I; IA
I
ADC input channel 4. Shared between 10-bit ADC0/1.
ADC0_5/
ADC1_5
B3
-
208
[8]
I; IA
I
ADC input channel 5. Shared between 10-bit ADC0/1.
ADC0_6/
ADC1_6
A5
-
204
[8]
I; IA
I
ADC input channel 6. Shared between 10-bit ADC0/1.
ADC0_7/
ADC1_7
C5
-
197
[8]
I; IA
I
ADC input channel 7. Shared between 10-bit ADC0/1.
A11
C3
186
[11]
-
O
RTC controlled output.
182
[8]
-
I
Input to the RTC 32 kHz ultra-low power oscillator circuit.
WAKEUP3
ADC pins
RTC
RTC_ALARM
RTCX1
A8
A5
RTCX2
B8
B5
183
[8]
-
O
Output from the RTC 32 kHz ultra-low power oscillator circuit.
SAMPLE
B9
-
-
[11]
O
O
Event monitor sample output.
B1
18
[8]
-
I
Input to the oscillator circuit and internal clock generator
circuits.
Crystal oscillator pins
XTAL1
LPC436X
Product data sheet
D1
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
57 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
XTAL2
19
[8]
Type
C1
Description
[1]
E1
Reset state
LQFP208
Pin name
TFBGA100
Pin description …continued
LBGA256
Table 3.
-
O
Output from the oscillator amplifier.
Power and ground pins
USB0_VDDA
3V3_DRIVER
F3
D1
24
-
-
Separate analog 3.3 V power supply for driver.
USB0
_VDDA3V3
G3
D2
25
-
-
USB 3.3 V separate power supply voltage.
USB0_VSSA
_TERM
H3
D3
27
-
-
Dedicated analog ground for clean reference for termination
resistors.
USB0_VSSA
_REF
G1
F2
31
-
-
Dedicated clean analog ground for generation of reference
currents and voltages.
VDDA
B4
B2
198
-
-
Analog power supply and ADC reference voltage.
VBAT
B10
C5
184
-
-
RTC power supply: 3.3 V on this pin supplies power to the
RTC.
VDDREG
F10, F9,
L8, L7
E4,
E5,
F4
135,
188,
195,
82, 33
-
Main regulator power supply. Tie the VDDREG and VDDIO
pins to a common power supply to ensure the same ramp-up
time for both supply voltages.
VPP
E8
-
-
[12]
-
-
OTP programming voltage.
-
-
I/O power supply. Tie the VDDREG and VDDIO pins to a
common power supply to ensure the same ramp-up time for
both supply voltages.
VDDIO
D7, E12, F10,
F7, F8,
K5
G10, H10,
J6, J7,
K7, L9,
L10, N7,
N13
6, 52,
57,
102,
110,
155,
160,
202
[12]
VSS
G9, H7,
J10, J11,
K8
-
[13]
-
-
Ground.
VSSIO
C4, D13, G6, G7,
G8, H8,
H9, J8,
J9, K9,
K10, M13,
P7, P13
5, 56,
109,
157
[13]
-
-
Ground.
VSSA
B2
196
-
-
Analog ground.
C8,
D4,
D5,
G8,
J3,
J6
C2
[1]
N = neutral, input buffer disabled; no extra VDDIO current consumption if the input is driven midway between supplies; set the EZI bit in
the SFS register to enable the input buffer; I = input, OL = output driving LOW; OH = output driving HIGH; AI/O = analog input/output; IA
= inactive; PU = pull-up enabled (weak pull-up resistor pulls up pin to VDDIO; F = floating. Reset state reflects the pin state at reset
without boot code operation.
[2]
5 V tolerant pad with 15 ns glitch filter (5 V tolerant if VDDIO present; if VDDIO not present, do not exceed 3.6 V); provides digital I/O
functions with TTL levels and hysteresis; normal drive strength.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
58 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
[3]
5 V tolerant pad with 15 ns glitch filter (5 V tolerant if VDDIO present; if VDDIO not present, do not exceed 3.6 V); provides digital I/O
functions with TTL levels, and hysteresis; high drive strength.
[4]
5 V tolerant pad with 15 ns glitch filter (5 V tolerant if VDDIO present; if VDDIO not present, do not exceed 3.6 V); provides high-speed
digital I/O functions with TTL levels and hysteresis.
[5]
5 V tolerant pad providing digital I/O functions (with TTL levels and hysteresis) and analog input or output (5 V tolerant if VDDIO present;
if VDDIO not present, do not exceed 3.6 V). When configured as a ADC input or DAC output, the pin is not 5 V tolerant and the digital
section of the pad must be disabled by setting the pin to an input function and disabling the pull-up resistor through the pin’s SFSP
register.
[6]
5 V tolerant transparent analog pad.
[7]
For maximum load CL = 6.5 F and maximum resistance Rpd = 80 k, the VBUS signal takes about 2 s to fall from VBUS = 5 V to VBUS
= 0.2 V when it is no longer driven.
[8]
Transparent analog pad. Not 5 V tolerant.
[9]
Pad provides USB functions; 5 V tolerant if VDDIO present; if VDDIO not present, do not exceed 3.6 V. It is designed in accordance with
the USB specification, revision 2.0 (Full-speed and Low-speed mode only).
[10] Open-drain 5 V tolerant digital I/O pad, compatible with I2C-bus Fast Mode Plus specification. This pad requires an external pull-up to
provide output functionality. When power is switched off, this pin connected to the I2C-bus is floating and does not disturb the I2C lines.
[11] 5 V tolerant pad with 20 ns glitch filter; provides digital I/O functions with open-drain output and hysteresis.
[12] On the LQFP208, VPP is internally connected to VDDIO.
[13] On the LQFP208 package, VSSIO and VSS are connected to a common ground plane.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
59 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7. Functional description
7.1 Architectural overview
The ARM Cortex-M4 includes three AHB-Lite buses: the system bus, the I-CODE bus,
and the D-code bus. The I-CODE and D-code core buses allow for concurrent code and
data accesses from different slave ports.
The LPC436x use a multi-layer AHB matrix to connect the ARM Cortex-M4 buses and
other bus masters to peripherals in a flexible manner that optimizes performance by
allowing peripherals that are on different slaves ports of the matrix to be accessed
simultaneously by different bus masters.
An ARM Cortex-M0 co-processor is included in the LPC436x, capable of off-loading the
main ARM Cortex-M4 application processor. Most peripheral interrupts are connected to
both processors. The processors communicate with each other via an interprocessor
communication protocol.
7.2 ARM Cortex-M4 processor
The ARM Cortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture
with separate local instruction and data buses as well as a third bus for peripherals, and
includes an internal prefetch unit that supports speculative branching. The ARM
Cortex-M4 supports single-cycle digital signal processing and SIMD instructions. A
hardware floating-point processor is integrated in the core. The processor includes a
NVIC with up to 53 interrupts.
7.3 ARM Cortex-M0 processors
The ARM Cortex-M0 processors are general purpose, 32-bit microprocessors, which offer
high performance and very low power consumption. The ARM Cortex-M0 processor uses
a 3-stage pipeline von Neumann architecture and a small but powerful instruction set
providing high-end processing hardware. The processors each incorporate an NVIC with
32 interrupts.
7.3.1 ARM Cortex-M0 coprocessor
The M0 coprocessor resides on the same AHB multi-layer matrix as the main Cortex-M0
core. The coprocessor can be used to off-load multiple tasks from the main Cortex-M4
processor.
7.3.2 ARM Cortex-M0 subsystem
The Cortex-M0 subsystem can be used to manage the SGPIO and SPI peripherals on the
M0 subsystem multilayer matrix but any other peripheral as well. The M0 subsystem is
separated by a bridge from the main AHB matrix. The M0 subsystem AHB matrix has two
SRAM blocks which allows to run the Cortex-M0 subsystem at full speed independently
from the main matrix.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
60 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
One application of using the subsystem is to reduce power, for example when the main
matrix runs at a very low speed and the M0 subsystem monitors activity and increases the
main matrix speed when needed. Another application for the subsystem is to manage the serial GPIO peripheral, which can be configured as additional SPI, I2S, or other serial interface.
One of the two SRAM blocks connected to the subsystem AHB matrix is typically used for
code running on the M0 subsystem and the other SRAM block for data. This allows other
bus masters to access the data SRAM without interrupting the M0 processor instruction
fetches and thereby stalling the M0 subsystem.
The M0 subsystem matrix runs at an asynchronous speed from the main matrix. This
allows to operate the SGPIO at any desired frequency. The M0 subsystem can control the
SGPIO in a deterministic way, without incurring latency that occurs when the M4 controls
the SGPIO through a bridge.
7.4 Interprocessor communication
The ARM Cortex-M4 and ARM Cortex-M0 interprocessor communication is based on
using shared SRAM as mailbox and one processor raising an interrupt on the other
processor's NVIC, for example after it has delivered a new message in the mailbox. The
receiving processor can reply by raising an interrupt on the sending processor's NVIC to
acknowledge the message.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
61 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7.5 AHB multilayer matrix
TEST/DEBUG
INTERFACE
ARM
CORTEX-M0
SUBSYSTEM
master
BRIDGE
TEST/DEBUG
INTERFACE
MPU
FPU
ARM
CORTEX-M4
TEST/DEBUG
INTERFACE
DMA
ARM
CORTEX-M0
HIGH-SPEED
PHY
slaves
USB1
LCD
SD/
MMC
masters
2 kB SRAM
USB0
APPLICATION
System
IDbus code code
bus bus
ETHERNET
16 kB SRAM
0
1
SPI
SGPIO
BRIDGE
slaves
512 kB FLASH A
512 kB FLASH B
16 kB EEPROM
64 kB ROM
32 kB LOCAL SRAM
40 kB LOCAL SRAM
32 kB AHB SRAM
16 kB + 16 kB
AHB SRAM
EXTERNAL
MEMORY
CONTROLLER
SPIFI
AHB PERIPHERALS
REGISTER
INTERFACES
BRIDGE0
APB0 PERIPHERALS
APB0 PERIPHERALS
BRIDGE
RTC PERIPHERALS
AHB MULTILAYER MATRIX
RTC PERIPHERALS
= master-slave connection
Fig 5.
aaa-018953
AHB multilayer matrix master and slave connections
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
62 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7.6 Nested Vectored Interrupt Controller (NVIC)
The NVIC is an integral part of the Cortex-M4. The tight coupling to the CPU allows for low
interrupt latency and efficient processing of late arriving interrupts.
The ARM Cortex-M0 co-processor has its own NVIC with 32 vectored interrupts. Most
peripheral interrupts are shared between the Cortex-M0 and Cortex-M4 NVICs.
7.6.1 Features
• ARM Cortex-M4 core:
– Controls system exceptions and peripheral interrupts
– Support for up to 53 vectored interrupts
– Eight programmable interrupt priority levels with hardware priority level masking
– Relocatable vector table
– Non-Maskable Interrupt (NMI)
– Software interrupt generation
• ARM Cortex-M0 core:
– Support for up to 32 interrupts
– Four programmable interrupt priority levels with hardware priority level masking
7.6.2 Interrupt sources
Each peripheral device has one interrupt line connected to the NVIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
7.7 System Tick timer (SysTick)
The ARM Cortex-M4 includes a system tick timer (SYSTICK) that is intended to generate
a dedicated SYSTICK exception at a 10 ms interval.
Remark: The SysTick is not included in the ARM Cortex-M0 core implementation.
7.8 Event router
The event router combines various internal signals, interrupts, and the external interrupt
pins (WAKEUP[3:0]) to create an interrupt in the NVIC, if enabled. In addition, the event
router creates a wake-up signal to the ARM core and the CCU for waking up from Sleep,
Deep-sleep, Power-down, and Deep power-down modes. Individual events can be
configured as edge or level sensitive and can be enabled or disabled in the event router.
The event router can be battery powered.
The following events if enabled in the event router can create a wake-up signal from
sleep, deep-sleep, power-down, and deep power-down modes and/or create an interrupt:
• External pins WAKEUP0/1/2/3 and RESET
• Alarm timer, RTC (32 kHz oscillator running)
The following events if enabled in the event router can create a wake-up signal from sleep
mode only and/or create an interrupt:
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
63 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
•
•
•
•
WWDT, BOD interrupts
C_CAN0/1 and QEI interrupts
Ethernet, USB0, USB1 signals
Selected outputs of combined timers (SCTimer/PWM and timer 0/1/3)
Remark: Any interrupt can wake up the ARM Cortex-M4 from sleep mode if enabled in
the NVIC.
7.9 Global Input Multiplexer Array (GIMA)
The GIMA allows to route signals to event-driven peripheral targets like the
SCTimer/PWM, timers, event router, or the ADCs.
7.9.1 Features
•
•
•
•
•
Single selection of a source.
Signal inversion.
Can capture a pulse if the input event source is faster than the target clock.
Synchronization of input event and target clock.
Single-cycle pulse generation for target.
7.10 On-chip static RAM
The LPC436x support up to 154 kB SRAM with separate bus master access for higher
throughput and individual power control for low power operation.
7.11 On-chip flash memory
The LPC436x contain up to 1 MB of dual-bank flash program memory. With dual-bank
flash memory, the user code can write or erase one flash bank while reading the other
flash bank without interruption. A two-port flash accelerator maximizes the flash
performance.
In-System Programming (ISP) and In-Application Programming (IAP) routines for
programming the flash memory are provided in the Boot ROM.
7.12 EEPROM
The LPC436x contain 16 kB of on-chip byte-erasable and byte-programmable EEPROM
memory.
The EEPROM memory is divided into 128 pages. The user can access pages 1 through
127. Page 128 is protected.
7.13 Boot ROM
The internal ROM memory is used to store the boot code of the LPC436x. After a reset,
the ARM processor will start its code execution from this memory.
The boot ROM memory includes the following features:
• The ROM memory size is 64 kB.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
64 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
• Supports booting from external static memory such as NOR flash, SPI flash, quad SPI
flash, USB0, and USB1.
• Includes API for OTP programming.
• Includes a flexible USB device stack that supports Human Interface Device (HID),
Mass Storage Class (MSC), and Device Firmware Upgrade (DFU) drivers.
Several boot modes are available if P2_7 is LOW on reset depending on the values of the
OTP bits BOOT_SRC. If the OTP memory is not programmed or the BOOT_SRC bits are
all zero, the boot mode is determined by the states of the boot pins P2_9, P2_8, P1_2,
and P1_1.
Table 4.
Boot mode when OTP BOOT_SRC bits are programmed
Boot mode BOOT_SRC BOOT_SRC BOOT_SRC
bit 3
bit 2
bit 1
BOOT_SRC Description
bit 0
Pin state
0
0
0
0
Boot source is defined by the reset state of P1_1,
P1_2, P2_8 pins, and P2_9. See Table 5.
USART0
0
0
0
1
Enter ISP mode using USART0 pins P2_0 and
P2_1.
SPIFI
0
0
1
0
Boot from Quad SPI flash connected to the SPIFI
interface using pins P3_3 to P3_8.
EMC 8-bit
0
0
1
1
Boot from external static memory (such as NOR
flash) using CS0 and an 8-bit data bus.
EMC 16-bit
0
1
0
0
Boot from external static memory (such as NOR
flash) using CS0 and a 16-bit data bus.
EMC 32-bit
0
1
0
1
Boot from external static memory (such as NOR
flash) using CS0 and a 32-bit data bus.
USB0
0
1
1
0
Boot from USB0.
USB1
0
1
1
1
Boot from USB1.
SPI (SSP)
1
0
0
0
Boot from SPI flash connected to the SSP0
interface on P3_3 (function SSP0_SCK), P3_6
(function SSP0_SSEL), P3_7 (function
SSP0_MISO), and P3_8 (function SSP0_MOSI)[1].
USART3
1
0
0
1
Enter ISP mode using USART3 pins P2_3 and
P2_4.
[1]
The boot loader programs the appropriate pin function at reset to boot using either SSP0 or SPIFI.
Remark: Pin functions for SPIFI and SSP0 boot are different.
Table 5.
Boot mode when OPT BOOT_SRC bits are zero
Boot mode
Pins
Description
P2_9
P2_8
P1_2
P1_1
USART0
LOW
LOW
LOW
LOW
Enter ISP mode using USART0 pins P2_0 and
P2_1.
SPIFI
LOW
LOW
LOW
HIGH
Boot from Quad SPI flash connected to the SPIFI
interface on P3_3 to P3_8[1].
EMC 8-bit
LOW
LOW
HIGH
LOW
Boot from external static memory (such as NOR
flash) using CS0 and an 8-bit data bus.
EMC 16-bit
LOW
LOW
HIGH
HIGH
Boot from external static memory (such as NOR
flash) using CS0 and a 16-bit data bus.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
65 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 5.
Boot mode when OPT BOOT_SRC bits are zero
Boot mode
Pins
Description
P2_9
P2_8
P1_2
P1_1
EMC 32-bit
LOW
HIGH
LOW
LOW
USB0
LOW
HIGH
LOW
HIGH
Boot from USB0
USB1
LOW
HIGH
HIGH
LOW
Boot from USB1.
SPI (SSP)
LOW
HIGH
HIGH
HIGH
Boot from SPI flash connected to the SSP0
interface on P3_3 (function SSP0_SCK), P3_6
(function SSP0_SSEL), P3_7 (function
SSP0_MISO), and P3_8 (function SSP0_MOSI)[1].
USART3
HIGH
LOW
LOW
LOW
Enter ISP mode using USART3 pins P2_3 and
P2_4.
[1]
Boot from external static memory (such as NOR
flash) using CS0 and a 32-bit data bus.
The boot loader programs the appropriate pin function at reset to boot using either SSP0 or SPIFI.
Remark: Pin functions for SPIFI and SSP0 boot are different.
7.14 Memory mapping
The memory map shown in Figure 6 and Figure 7 is global to both the Cortex-M4 and the
Cortex-M0 processors and all SRAM, flash, and EEPROM memory is shared between
both processors. Each processor uses its own ARM private bus memory map for the
NVIC and other system functions.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
66 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
LPC436x
4 GB
0xFFFF FFFF
reserved
0xE010 0000
ARM private bus
0xE000 0000
reserved
0x8800 0000
128 MB SPIFI data
0x8000 0000
256 MB dynamic external memory DYCS3
256 MB dynamic external memory DYCS2
reserved
0x1F00 0000
0x1E00 0000
0x1D00 0000
0x1C00 0000
reserved
SGPIO
16 MB static external memory CS2
SPI
16 MB static external memory CS1
16 MB static external memory CS0
256 kB flash B
APB peripherals #3
0x1041 0000
0x1040 0000
0x1008 A000
0x400F 0000
reserved
reserved
256 kB flash A
0x400A 0000
reserved
0x4009 0000
APB peripherals #0
0x4008 0000
reserved
0x4006 0000
8 kB ROM (M0 SERIAL)
clocking/reset peripherals
RTC domain peripherals
0x4005 0000
0x4004 0000
reserved
0x4001 2000
2 kB SRAM (M0 subsystem)
AHB peripherals
1 GB
16 kB SRAM (M0 subsystem)
0x4000 0000
256 MB dynamic external memory DYCS1
64 MB SPIFI data
128 MB dynamic external memory DYCS0
reserved
0x3000 0000
0x2800 0000
reserved
0x2400 0000
64 kB ROM
32 MB AHB SRAM bit banding
reserved
0x2200 0000
reserved
32 kB + 8 kB local SRAM
0x1008 0000
0x2004 4000
16 kB EEPROM
reserved
0x2004 0000
reserved
0x2001 0000
4 x 16 kB AHB SRAM
0x1000 8000
0x1000 0000
0x400C 0000
0x400B 0000
APB peripherals #1
256 kB flash A
0x400E 0000
0x400D 0000
APB peripherals #2
0x1800 4800
0x1400 0000
0x400F 1000
reserved
reserved
0x1800 0000
0x400F 2000
256 kB flash B
0x1840 2000
0x1800 4000
0x400F 4000
reserved
reserved
0x1840 0000
0x400F 8000
reserved
0x1A08 0000
0x1A00 0000
0x4010 0000
high-speed GPIO
reserved
0x1A04 0000
0x4010 1000
reserved
0x1B08 0000
0x1B00 0000
0x4200 0000
0x4010 2000
16 MB static external memory CS3
reserved
0x1B04 0000
0x6000 0000
0x4400 0000
peripheral bit band alias region
0x2000 0000
0x7000 0000
local SRAM/
external static memory banks
32 kB local SRAM
0 GB
256 MB shadow area
0x2000 0000
0x1000 0000
0x0000 0000
aaa-018954
Fig 6.
LPC436x Memory mapping (overview)
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
67 of 156
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
0x400E 5000
reserved
0x400E 4000
ADC1
0x400E 3000
ADC0
0x400E 2000
C_CAN0
0x400E 1000
DAC
0x400E 0000
0x400C 8000
I2C1
0x400C 7000
0xFFFF FFFF
APB3
peripherals
external memories and
ARM private bus
0x6000 0000
reserved
peripheral bit band alias region
reserved
SGPIO
GIMA
Rev. 1.2 — 14 March 2016
QEI
0x400C 5000
SSP1
0x400C 4000
timer3
0x400C 3000
timer2
0x400C 2000
USART3
0x400C 1000
USART2
reserved
0x400C 0000
0x400B 0000
RI timer
APB3 peripherals
reserved
reserved
0x400A 4000
0x400A 3000
0x400A 2000
0x400A 1000
0x400A 0000
0x4008 A000
0x4008 9000
0x4008 8000
0x4008 7000
C_CAN1
I2S1
I2S0
I2C0
APB2
peripherals
reserved
APB2 peripherals
reserved
APB1 peripherals
reserved
APB0 peripherals
reserved
GPIO GROUP1 interrupt
GPIO GROUP0 interrupt
GPIO interrupts
SCU
0x4008 5000
timer1
0x4008 4000
timer0
0x4008 3000
SSP0
0x4008 2000
UART1 w/ modem
0x4008 1000
USART0
0x4008 0000
WWDT
RTC domain peripherals
APB0
peripherals
0x4005 3000
0x4005 2000
CCU1
0x4005 1000
CGU
0x4005 0000
reserved
0x4005 0000
0x4004 7000
RTC/event monitor
0x4004 6000
OTP controller
0x4004 5000
event router
0x4004 4000
CREG
0x4004 3000
0x4010 2000
0x4010 1000
0x4010 0000
0x400F 4000
RTC domain
peripherals
0x400F 2000
power mode control
0x4004 2000
0x400F 1000
backup registers
0x4004 1000
0x400F 0000
alarm timer
0x400E 0000
0x400D 0000
reserved
0x400C 0000
ethernet
0x400B 0000
reserved
0x400A 0000
EEPROM controller
flash B controller
0x4009 0000
flash A controller
0x4008 0000
0x4006 0000
reserved
0x4004 0000
0x4002 0000
0x4001 2000
0x4001 0000
0x4000 F000
0x4000 E000
0x4000 D000
0x4000 C000
0x4000 9000
LCD
0x4000 8000
USB1
0x4004 0000
0x4000 7000
USB0
0x4000 6000
0x4002 0000
EMC
0x4000 5000
0x4000 0000
SD/MMC
0x4000 4000
SPIFI
0x4000 3000
DMA
0x4000 2000
reserved
0x4000 1000
SCT
0x4000 0000
0x4005 0000
reserved
AHB peripherals
SRAM, flash, EEPROM memories
external memory banks
RGU
CCU2
0x1000 0000
256 MB memory shadow area
0x0000 0000
AHB
peripherals
aaa-018955
Fig 7.
LPC436x Memory mapping (peripherals)
LPC436x
68 of 156
© NXP Semiconductors N.V. 2016. All rights reserved.
0x4008 6000
clocking/reset peripherals
0x4006 0000
0x4005 4000
0x4200 0000
0x400F 8000
reserved
motor control PWM
0x4400 0000
reserved
high-speed GPIO
APB1
peripherals
clocking
reset control
peripherals
reserved
32-bit ARM Cortex-M4/M0 microcontroller
All information provided in this document is subject to legal disclaimers.
SPI
0x400C 6000
0x400A 5000
NXP Semiconductors
LPC436X
Product data sheet
LPC436x
0x400F 0000
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7.15 One-Time Programmable (OTP) memory
The OTP provides 64 bit+ 256 bit of memory for general-purpose use.
7.16 General Purpose I/O (GPIO)
The LPC436x provide eight GPIO ports with up to 31 GPIO pins each.
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back as well as the current state of the port pins.
All GPIO pins default to inputs with pull-up resistors enabled and input buffer disabled on
reset. The input buffer must be turned on in the system control block SFS register before
the GPIO input can be read.
7.16.1 Features
• Accelerated GPIO functions:
– GPIO registers are located on the AHB so that the fastest possible I/O timing can
be achieved.
– Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
– All GPIO registers are byte and half-word addressable.
– Entire port value can be written in one instruction.
• Bit-level set and clear registers allow a single instruction set or clear of any number of
bits in one port.
• Direction control of individual bits.
• Up to eight GPIO pins can be selected from all GPIO pins to create an edge- or
level-sensitive GPIO interrupt request (GPIO interrupts).
• Two GPIO group interrupts can be triggered by any pin or pins in each port (GPIO
group0 and group1 interrupts).
7.17 Configurable digital peripherals
7.17.1 SCTimer/PWM
The SCTimer/PWM allows a wide variety of timing, counting, output modulation, and input
capture operations. The inputs and outputs of the SCTimer/PWM are shared with the
capture and match inputs/outputs of the 32-bit general purpose counter/timers.
The SCTimer/PWM can be configured as two 16-bit counters or a unified 32-bit counter. In
the two-counter case, in addition to the counter value the following operational elements
are independent for each half:
• State variable.
• Limit, halt, stop, and start conditions.
• Values of Match/Capture registers, plus reload or capture control values.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
69 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
In the two-counter case, the following operational elements are global to the
SCTimer/PWM, but the last three can use match conditions from either counter:
•
•
•
•
•
7.17.1.1
Clock selection
Inputs
Events
Outputs
Interrupts
Features
•
•
•
•
•
Two 16-bit counters or one 32-bit counter.
Counters clocked by bus clock or selected input.
Up counters or up-down counters.
State variable allows sequencing across multiple counter cycles.
The following conditions define an event: a counter match condition, an input (or
output) condition, a combination of a match and/or and input/output condition in a
specified state.
• Events control outputs, interrupts, and DMA requests.
– Match register 0 can be used as an automatic limit.
– In bi-directional mode, events can be enabled based on the count direction.
– Match events can be held until another qualifying event occurs.
• Selected events can limit, halt, start, or stop a counter.
• Supports:
– 8 inputs
– 16 outputs
– 16 match/capture registers
– 16 events
– 32 states
– Match register 0 to 5 support a fractional component for the dither engine
7.17.2 Serial GPIO (SGPIO)
The Serial GPIOs offer standard GPIO functionality enhanced with features to accelerate
serial stream processing.
7.17.2.1
Features
• Each SGPIO input/output slice can be used to perform a serial to parallel or parallel to
serial data conversion.
• 16 SGPIO input/output slices each with a 32-bit FIFO that can shift the input value
from a pin or an output value to a pin with every cycle of a shift clock.
• Each slice is double-buffered.
• Interrupt is generated on a full FIFO, shift clock, or pattern match.
• Slices can be concatenated to increase buffer size.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
70 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
• Each slice has a 32-bit pattern match filter.
7.18 AHB peripherals
7.18.1 General Purpose DMA
The DMA controller allows peripheral-to memory, memory-to-peripheral,
peripheral-to-peripheral, and memory-to-memory transactions. Each DMA stream
provides unidirectional serial DMA transfers for a single source and destination. For
example, a bidirectional port requires one stream for transmit and one for receives. The
source and destination areas can each be either a memory region or a peripheral for
master 1, but only memory for master 0.
7.18.1.1
Features
• Eight DMA channels. Each channel can support a unidirectional transfer.
• 16 DMA request lines.
• Single DMA and burst DMA request signals. Each peripheral connected to the DMA
Controller can assert either a burst DMA request or a single DMA request. The DMA
burst size is set by programming the DMA Controller.
• Memory-to-memory, memory-to-peripheral, peripheral-to-memory, and
peripheral-to-peripheral transfers are supported.
• Scatter or gather DMA is supported through the use of linked lists. This means that
the source and destination areas do not have to occupy contiguous areas of memory.
• Hardware DMA channel priority.
• AHB slave DMA programming interface. The DMA Controller is programmed by
writing to the DMA control registers over the AHB slave interface.
• Two AHB bus masters for transferring data. These interfaces transfer data when a
DMA request goes active. Master 1 can access memories and peripherals, master 0
can access memories only.
• 32-bit AHB master bus width.
• Incrementing or non-incrementing addressing for source and destination.
• Programmable DMA burst size. The DMA burst size can be programmed to more
efficiently transfer data.
• Internal four-word FIFO per channel.
• Supports 8, 16, and 32-bit wide transactions.
• Big-endian and little-endian support. The DMA Controller defaults to little-endian
mode on reset.
• An interrupt to the processor can be generated on a DMA completion or when a DMA
error has occurred.
• Raw interrupt status. The DMA error and DMA count raw interrupt status can be read
prior to masking.
7.18.2 SPI Flash Interface (SPIFI)
The SPI Flash Interface allows low-cost serial flash memories to be connected to the ARM
Cortex-M4 processor with little performance penalty compared to parallel flash devices
with higher pin count.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
71 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
After a few commands configure the interface at startup, the entire flash content is
accessible as normal memory using byte, halfword, and word accesses by the processor
and/or DMA channels. Simple sequences of commands handle erasing and
programming.
Many serial flash devices use a half-duplex command-driven SPI protocol for device setup
and initialization and then move to a half-duplex, command-driven 4-bit protocol for
normal operation. Different serial flash vendors and devices accept or require different
commands and command formats. SPIFI provides sufficient flexibility to be compatible
with common flash devices and includes extensions to help insure compatibility with future
devices.
7.18.2.1
Features
•
•
•
•
Interfaces to serial flash memory in the main memory map.
Supports classic and 4-bit bidirectional serial protocols.
Half-duplex protocol compatible with various vendors and devices.
Quad SPI Flash Interface (SPIFI) with 1-, 2-, or 4-bit data at rates of up to 52 MB per
second.
• Supports DMA access.
7.18.3 SD/MMC card interface
The SD/MMC card interface supports the following modes to control:
•
•
•
•
Secure Digital memory (SD version 3.0)
Secure Digital I/O (SDIO version 2.0)
Consumer Electronics Advanced Transport Architecture (CE-ATA version 1.1)
MultiMedia Cards (MMC version 4.4)
7.18.4 External Memory Controller (EMC)
Remark: The EMC is available on all LPC436x parts. The following memory bus widths
are supported:
• LBGA256 packages: 32 bit
• TFBGA100 packages: 16 bit
• LQFP208 packages: 16 bit
The LPC436x EMC is a Memory Controller peripheral offering support for asynchronous
static memory devices such as RAM, ROM, and NOR flash. In addition, it can be used as
an interface with off-chip memory-mapped devices and peripherals.
Table 6.
Function
LPC436X
Product data sheet
EMC pinout for different packages
LBGA256
TFBGA100
LQFP208
A
EMC_A[23:0]
EMC_A[13:0]
EMC_A[23:0]
D
EMC_D[31:0]
EMC_D[15:0]
EMC_D[15:0]
BLS
EMC_BLS[3:0]
EMC_BLS0
EMC_BLS[1:0]
CS
EMC_CS[3:0]
EMC_CS0
EMC_CS[3:0]
OE
EMC_OE
EMC_OE
EMC_OE
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
72 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 6.
7.18.4.1
EMC pinout for different packages
Function
LBGA256
TFBGA100
LQFP208
WE
EMC_WE
EMC_WE
EMC_WE
CKEOUT
EMC_
CKEOUT[3:0]
EMC_
CKEOUT[1:0]
EMC_
CKEOUT[1:0]
CLK
EMC_CLK[3:0];
EMC_CLK01,
EMC_CLK23
EMC_CLK0, EMC_CLK3;
EMC_CLK01,
EMC_CLK23
EMC_CLK0, EMC_CLK3;
EMC_CLK01,
EMC_CLK23
DQMOUT
EMC_
DQMOUT[3:0]
-
EMC_
DQMOUT[1:0]
DYCS
EMC_
DYCS[3:0]
EMC_DYCS[1:0]
EMC_DYCS[2:0]
CAS
EMC_CAS
EMC_CAS
EMC_CAS
RAS
EMC_RAS
EMC_RAS
EMC_RAS
Features
• Dynamic memory interface support including single data rate SDRAM.
• Asynchronous static memory device support including RAM, ROM, and NOR flash,
with or without asynchronous page mode.
•
•
•
•
•
Low transaction latency.
Read and write buffers to reduce latency and to improve performance.
8/16/32 data and 24 address lines wide static memory support.
16 bit and 32 bit wide chip select SDRAM memory support.
Static memory features include:
– Asynchronous page mode read
– Programmable Wait States
– Bus turnaround delay
– Output enable and write enable delays
– Extended wait
• Four chip selects for synchronous memory and four chip selects for static memory
devices.
• Power-saving modes dynamically control EMC_CKEOUT and EMC_CLK signals to
SDRAMs.
• Dynamic memory self-refresh mode controlled by software.
• Controller supports 2048 (A0 to A10), 4096 (A0 to A11), and 8192 (A0 to A12) row
address synchronous memory parts. Those are typically 512 MB, 256 MB, and
128 MB parts, with 4, 8, 16, or 32 data bits per device.
• Separate reset domains allow the for auto-refresh through a chip reset if desired.
• SDRAM clock can run at full or half the Cortex-M4 core frequency.
Note: Synchronous static memory devices (synchronous burst mode) are not supported.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
73 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7.18.5 High-speed USB Host/Device/OTG interface (USB0)
Remark: USB0 is available on the following parts: LPC435x, LPC433x, LPC432x. USB0
is not available on the LPC431x parts.
The USB OTG module allows the LPC436x to connect directly to a USB Host such as a
PC (in device mode) or to a USB Device in host mode.
7.18.5.1
Features
•
•
•
•
•
•
•
•
•
•
•
•
Contains UTMI+ compliant high-speed transceiver (PHY).
Complies with Universal Serial Bus specification 2.0.
Complies with USB On-The-Go supplement.
Complies with Enhanced Host Controller Interface Specification.
Supports auto USB 2.0 mode discovery.
Supports all high-speed USB-compliant peripherals.
Supports all full-speed USB-compliant peripherals.
Supports software Host Negotiation Protocol (HNP) and Session Request Protocol
(SRP) for OTG peripherals.
Supports interrupts.
Supports Start Of Frame (SOF) frame length adjust.
This module has its own, integrated DMA engine.
USB interface electrical test software included in ROM USB stack.
7.18.6 High-speed USB Host/Device interface with ULPI (USB1)
Remark: USB1 is available on the following parts: LPC435x and LPC433x. USB1 is not
available on the LPC432x and LPC431x parts.
The USB1 interface can operate as a full-speed USB Host/Device interface or can
connect to an external ULPI PHY for High-speed operation.
7.18.6.1
Features
•
•
•
•
Complies with Universal Serial Bus specification 2.0.
•
•
•
•
•
Supports all full-speed USB-compliant peripherals.
Complies with Enhanced Host Controller Interface Specification.
Supports auto USB 2.0 mode discovery.
Supports all high-speed USB-compliant peripherals if connected to external ULPI
PHY.
Supports interrupts.
Supports Start Of Frame (SOF) frame length adjust.
This module has its own, integrated DMA engine.
USB interface electrical test software included in ROM USB stack.
7.18.7 LCD controller
Remark: The LCD controller is only available on parts LPC435x. LCD is not available on
parts LPC433x, LPC432x, and LPC431x.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
74 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
The LCD controller provides all of the necessary control signals to interface directly to
various color and monochrome LCD panels. Both STN (single and dual panel) and TFT
panels can be operated. The display resolution is selectable and can be up to 1024 768
pixels. Several color modes are provided, up to a 24-bit true-color non-palettized mode.
An on-chip 512 byte color palette allows reducing bus utilization (that is, memory size of
the displayed data) while still supporting many colors.
The LCD interface includes its own DMA controller to allow it to operate independently of
the CPU and other system functions. A built-in FIFO acts as a buffer for display data,
providing flexibility for system timing. Hardware cursor support can further reduce the
amount of CPU time required to operate the display.
7.18.7.1
Features
•
•
•
•
AHB master interface to access frame buffer.
Setup and control via a separate AHB slave interface.
Dual 16-deep programmable 64-bit wide FIFOs for buffering incoming display data.
Supports single and dual-panel monochrome Super Twisted Nematic (STN) displays
with 4-bit or 8-bit interfaces.
• Supports single and dual-panel color STN displays.
• Supports Thin Film Transistor (TFT) color displays.
• Programmable display resolution including, but not limited to: 320 200, 320 240,
640 200, 640 240, 640 480, 800 600, and 1024 768.
•
•
•
•
•
•
•
•
•
•
•
•
Hardware cursor support for single-panel displays.
15 gray-level monochrome, 3375 color STN, and 32 K color palettized TFT support.
1, 2, or 4 bits-per-pixel (bpp) palettized displays for monochrome STN.
1, 2, 4, or 8 bpp palettized color displays for color STN and TFT.
16 bpp true-color non-palettized for color STN and TFT.
24 bpp true-color non-palettized for color TFT.
Programmable timing for different display panels.
256 entry, 16-bit palette RAM, arranged as a 128 32-bit RAM.
Frame, line, and pixel clock signals.
AC bias signal for STN, data enable signal for TFT panels.
Supports little and big-endian, and Windows CE data formats.
LCD panel clock may be generated from the peripheral clock, or from a clock input
pin.
7.18.8 Ethernet
Remark: The ethernet controller is available on parts LPC435x and LPC433x. Ethernet is
not available on parts LPC432x and LPC431x.
7.18.8.1
Features
• 10/100 Mbit/s
• DMA support
• Power management remote wake-up frame and magic packet detection
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
75 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
• Supports both full-duplex and half-duplex operation
– Supports CSMA/CD Protocol for half-duplex operation.
– Supports IEEE 802.3x flow control for full-duplex operation.
– Optional forwarding of received pause control frames to the user application in
full-duplex operation.
– Back-pressure support for half-duplex operation.
– Automatic transmission of zero-quanta pause frame on deassertion of flow control
input in full-duplex operation.
• Supports IEEE1588 time stamping and IEEE 1588 advanced time stamping (IEEE
1588-2008 v2).
7.19 Digital serial peripherals
7.19.1 UART1
Remark: The LPC436x contain one UART with standard transmit and receive data lines.
UART1 also provides a full modem control handshake interface and support for
RS-485/9-bit mode allowing both software address detection and automatic address
detection using 9-bit mode.
UART1 includes a fractional baud rate generator. Standard baud rates such as 115200 Bd
can be achieved with any crystal frequency above 2 MHz.
7.19.1.1
Features
•
•
•
•
•
Maximum UART data bit rate of 8 MBit/s.
16 B Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
• Auto baud capabilities and FIFO control mechanism that enables software flow
control implementation.
• Equipped with standard modem interface signals. This module also provides full
support for hardware flow control.
• Support for RS-485/9-bit/EIA-485 mode (UART1).
• DMA support.
7.19.2 USART0/2/3
Remark: The LPC436x contain three USARTs. In addition to standard transmit and
receive data lines, the USARTs support a synchronous mode.
The USARTs include a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
7.19.2.1
Features
• Maximum UART data bit rate of 8 MBit/s.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
76 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
•
•
•
•
16 B Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
• Auto baud capabilities and FIFO control mechanism that enables software flow
control implementation.
•
•
•
•
•
Support for RS-485/9-bit/EIA-485 mode.
USART3 includes an IrDA mode to support infrared communication.
All USARTs have DMA support.
Support for synchronous mode at a data bit rate of up to 8 Mbit/s.
Smart card mode conforming to ISO7816 specification
7.19.3 SPI serial I/O controller
Remark: The LPC436x contain one SPI controller.
SPI is a full duplex serial interface designed to handle multiple masters and slaves
connected to a given bus. Only a single master and a single slave can communicate on
the interface during a given data transfer. During a data transfer the master always sends
8 bits to 16 bits of data to the slave, and the slave always sends 8 bits to 16 bits of data to
the master.
7.19.3.1
Features
•
•
•
•
•
•
Maximum SPI data bit rate 25 Mbit/s.
Compliant with SPI specification
Synchronous, serial, full duplex communication
Combined SPI master and slave
Maximum data bit rate of one eighth of the input clock rate
8 bits to 16 bits per transfer
7.19.4 SSP serial I/O controller
Remark: The LPC436x contain two SSP controllers.
The SSP controller can operate on a SPI, 4-wire SSI, or Microwire bus. It can interact with
multiple masters and slaves on the bus. Only a single master and a single slave can
communicate on the bus during a given data transfer. The SSP supports full duplex
transfers, with frames of 4 bit to 16 bit of data flowing from the master to the slave and
from the slave to the master. In practice, often only one of these data flows carries
meaningful data.
7.19.4.1
Features
• Maximum SSP speed in full-duplex mode of 25 Mbit/s; for transmit only 50 Mbit/s
(master) and 15 Mbit/s (slave)
• Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National
Semiconductor Microwire buses
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
77 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
•
•
•
•
•
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
DMA transfers supported by GPDMA
7.19.5 I2C-bus interface
Remark: The LPC436x each contain two I2C-bus interfaces.
The I2C-bus is bidirectional for inter-IC control using only two wires: a Serial Clock line
(SCL) and a Serial Data line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (for example an LCD driver) or a transmitter
with the capability to both receive and send information (such as memory). Transmitters
and/or receivers can operate in either master or slave mode, depending on whether the
chip has to initiate a data transfer or is only addressed. The I2C is a multi-master bus and
can be controlled by more than one bus master connected to it.
7.19.5.1
Features
• I2C0 is a standard I2C compliant bus interface with open-drain pins. I2C0 also
supports Fast mode plus with bit rates up to 1 Mbit/s.
•
•
•
•
•
•
I2C1 uses standard I/O pins with bit rates of up to 400 kbit/s (Fast I2C-bus).
Easy to configure as master, slave, or master/slave.
Programmable clocks allow versatile rate control.
Bidirectional data transfer between masters and slaves.
Multi-master bus (no central master).
Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus.
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus.
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer.
• The I2C-bus can be used for test and diagnostic purposes.
• All I2C-bus controllers support multiple address recognition and a bus monitor mode.
7.19.6 I2S interface
Remark: The LPC436x each contain two I2S-bus interfaces.
The I2S-bus provides a standard communication interface for digital audio applications.
The I2S-bus specification defines a 3-wire serial bus using one data line, one clock line,
and one word select signal. The basic I2S-bus connection has one master, which is
always the master, and one slave. The I2S-bus interface provides a separate transmit and
receive channel, each of which can operate as either a master or a slave.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
78 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7.19.6.1
Features
• The I2S interfaces has separate input/output channels, each of which can operate in
master or slave mode.
• Capable of handling 8-bit, 16-bit, and 32-bit word sizes.
• Mono and stereo audio data supported.
• The sampling frequency can range from 16 kHz to 192 kHz (16, 22.05, 32, 44.1, 48,
96, 192) kHz.
• Support for an audio master clock.
• Configurable word select period in master mode (separately for I2S-bus input and
output).
• Two 8-word FIFO data buffers are provided, one for transmit and one for receive.
• Generates interrupt requests when buffer levels cross a programmable boundary.
• Two DMA requests controlled by programmable buffer levels. The DMA requests are
connected to the GPDMA block.
• Controls include reset, stop and mute options separately for I2S-bus input and I2S-bus
output.
7.19.7 C_CAN
Remark: The LPC436x each contain two C_CAN controllers.
Controller Area Network (CAN) is the definition of a high performance communication
protocol for serial data communication. The C_CAN controller is designed to provide a full
implementation of the CAN protocol according to the CAN Specification Version 2.0B. The
C_CAN controller allows to build powerful local networks with low-cost multiplex wiring by
supporting distributed real-time control with a high level of reliability.
7.19.7.1
Features
•
•
•
•
•
•
•
Conforms to protocol version 2.0 parts A and B.
Supports bit rate of up to 1 Mbit/s.
Supports 32 Message Objects.
Each Message Object has its own identifier mask.
Provides programmable FIFO mode (concatenation of Message Objects).
Provides maskable interrupts.
Supports Disabled Automatic Retransmission (DAR) mode for time-triggered CAN
applications.
• Provides programmable loop-back mode for self-test operation.
7.20 Counter/timers and motor control
7.20.1 General purpose 32-bit timers/external event counters
Remark: The LPC436x include four 32-bit timer/counters.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
79 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
The timer/counter is designed to count cycles of the system derived clock or an
externally-supplied clock. It can optionally generate interrupts, generate timed DMA
requests, or perform other actions at specified timer values, based on four match
registers. Each timer/counter also includes two capture inputs to trap the timer value when
an input signal transitions, optionally generating an interrupt.
7.20.1.1
Features
• A 32-bit timer/counter with a programmable 32-bit prescaler.
• Counter or timer operation.
• Two 32-bit capture channels per timer, that can take a snapshot of the timer value
when an input signal transitions. A capture event can also generate an interrupt.
• Four 32-bit match registers that allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
• Up to four external outputs corresponding to match registers, with the following
capabilities:
– Set LOW on match.
– Set HIGH on match.
– Toggle on match.
– Do nothing on match.
• Up to two match registers can be used to generate timed DMA requests.
7.20.2 Motor control PWM
The motor control PWM is a specialized PWM supporting 3-phase motors and other
combinations. Feedback inputs are provided to automatically sense rotor position and use
that information to ramp speed up or down. An abort input causes the PWM to release all
motor drive outputs immediately . At the same time, the motor control PWM is highly
configurable for other generalized timing, counting, capture, and compare applications.
7.20.3 Quadrature Encoder Interface (QEI)
A quadrature encoder, also known as a 2-channel incremental encoder, converts angular
displacement into two pulse signals. By monitoring both the number of pulses and the
relative phase of the two signals, the user code can track the position, direction of rotation,
and velocity. In addition, a third channel, or index signal, can be used to reset the position
counter. The quadrature encoder interface decodes the digital pulses from a quadrature
encoder wheel to integrate position over time and determine direction of rotation. In
addition, the QEI can capture the velocity of the encoder wheel.
7.20.3.1
Features
•
•
•
•
•
LPC436X
Product data sheet
Tracks encoder position.
Increments/decrements depending on direction.
Programmable for 2 or 4 position counting.
Velocity capture using built-in timer.
Velocity compare function with “less than” interrupt.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
80 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
•
•
•
•
•
Uses 32-bit registers for position and velocity.
Three position compare registers with interrupts.
Index counter for revolution counting.
Index compare register with interrupts.
Can combine index and position interrupts to produce an interrupt for whole and
partial revolution displacement.
• Digital filter with programmable delays for encoder input signals.
• Can accept decoded signal inputs (clk and direction).
7.20.4 Repetitive Interrupt (RI) timer
The repetitive interrupt timer provides a free-running 32-bit counter which is compared to
a selectable value, generating an interrupt when a match occurs. Any bits of the
timer/compare function can be masked such that they do not contribute to the match
detection. The repetitive interrupt timer can be used to create an interrupt that repeats at
predetermined intervals.
7.20.4.1
Features
• 32-bit counter. Counter can be free-running or be reset by a generated interrupt.
• 32-bit compare value.
• 32-bit compare mask. An interrupt is generated when the counter value equals the
compare value, after masking. This mechanism allows for combinations not possible
with a simple compare.
7.20.5 Windowed WatchDog Timer (WWDT)
The purpose of the watchdog is to reset the controller if software fails to periodically
service it within a programmable time window.
7.20.5.1
Features
• Internally resets chip if not periodically reloaded during the programmable time-out
period.
• Optional windowed operation requires reload to occur between a minimum and
maximum time period, both programmable.
• Optional warning interrupt can be generated at a programmable time prior to
watchdog time-out.
• Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
•
•
•
•
Incorrect feed sequence causes reset or interrupt if enabled.
Flag to indicate watchdog reset.
Programmable 24-bit timer with internal prescaler.
Selectable time period from (Tcy(WDCLK) 256 4) to (Tcy(WDCLK) 224 4) in
multiples of Tcy(WDCLK) 4.
• The Watchdog Clock (WDCLK) uses the IRC as the clock source.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
81 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7.21 Analog peripherals
7.21.1 Analog-to-Digital Converter (ADC0/1)
Remark: The LPC436x contain two 10-bit ADCs.
7.21.1.1
Features
•
•
•
•
•
•
•
10-bit successive approximation analog to digital converter.
Input multiplexing among 8 pins.
Power-down mode.
Measurement range 0 to VDDA.
Sampling frequency up to 400 kSamples/s.
Burst conversion mode for single or multiple inputs.
Optional conversion on transition on ADCTRIG0 or ADCTRIG1 pins, combined timer
outputs 8 or 15, or the PWM output MCOA2.
• Individual result registers for each A/D channel to reduce interrupt overhead.
• DMA support.
7.21.2 Digital-to-Analog Converter (DAC)
7.21.2.1
Features
•
•
•
•
10-bit resolution
Monotonic by design (resistor string architecture)
Controllable conversion speed
Low power consumption
7.22 Peripherals in the RTC power domain
7.22.1 RTC
The Real Time Clock (RTC) is a set of counters for measuring time when system power is
on, and optionally when it is off. It uses little power when the CPU does not access its
registers, especially in the reduced power modes. A separate 32 kHz oscillator clocks the
RTC. The oscillator produces a 1 Hz internal time reference and is powered by its own
power supply pin, VBAT.
7.22.1.1
Features
• Measures the passage of time to maintain a calendar and clock. Provides seconds,
minutes, hours, day of month, month, year, day of week, and day of year.
• Ultra-low power design to support battery powered systems. Uses power from the
CPU power supply when it is present.
•
•
•
•
LPC436X
Product data sheet
Dedicated battery power supply pin.
RTC power supply is isolated from the rest of the chip.
Calibration counter allows adjustment to better than 1 sec/day with 1 sec resolution.
Periodic interrupts can be generated from increments of any field of the time registers.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
82 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
• Alarm interrupt can be generated for a specific date/time.
7.22.1.2
Event monitor/recorder
The event monitor/recorder allows recording and creating a time stamp of events related
to the WAKEUP pins. Sensors report changes to the state of the WAKEUP pins, and the
event monitor/recorder stores records of such events. The event recorder can be
powered by the backup battery.
The event monitor/recorder can monitor the integrity of the device and record any
tampering events.
Features
• Supports three digital event inputs in the VBAT power domain.
• An event is defined as a level change at the digital event inputs.
• For each event channel, two timestamps mark the first and the last occurrence of an
event. Each channel also has a dedicated counter tracking the total number of events.
Timestamp values are taken from the RTC.
• Runs in VBAT power domain, independent of system power supply. The
event/recorder/monitor can therefore operate in Deep power-down mode.
•
•
•
•
Low power consumption.
Interrupt available if system is running.
A qualified event can be used as a wake-up trigger.
State of event interrupts accessible by software through GPIO.
7.22.2 Alarm timer
The alarm timer is a 16-bit timer and counts down at 1 kHz from a preset value generating
alarms in intervals of up to 1 min. The counter triggers a status bit when it reaches 0x00
and asserts an interrupt if enabled.
The alarm timer is part of the RTC power domain and can be battery powered.
7.23 System control
7.23.1 Configuration registers (CREG)
The following settings are controlled in the configuration register block:
•
•
•
•
•
•
•
BOD trip settings
Oscillator output
DMA-to-peripheral muxing
Ethernet mode
Memory mapping
Timer/USART inputs
Enabling the USB controllers
In addition, the CREG block contains the part identification and part configuration
information.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
83 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7.23.2 System Control Unit (SCU)
The system control unit determines the function and electrical mode of the digital pins. By
default function 0 is selected for all pins with pull-up enabled. For pins that support a
digital and analog function, the ADC function select registers in the SCU enable the
analog function.
A separate set of analog I/Os for the ADCs and the DAC as well as most USB pins are
located on separate pads and are not controlled through the SCU.
In addition, the clock delay register for the SDRAM EMC_CLK pins and the registers that
select the pin interrupts are located in the SCU.
7.23.3 Clock Generation Unit (CGU)
The Clock Generator Unit (CGU) generates several base clocks. The base clocks can be
unrelated in frequency and phase and can have different clock sources within the CGU.
One CGU base clock is routed to the CLKOUT pins. The base clock that generates the
CPU clock is referred to as CCLK.
Multiple branch clocks are derived from each base clock. The branch clocks offer flexible
control for power-management purposes. All branch clocks are outputs of one of two
Clock Control Units (CCUs) and can be controlled independently. Branch clocks derived
from the same base clock are synchronous in frequency and phase.
7.23.4 Internal RC oscillator (IRC)
The IRC is used as the clock source for the WWDT and/or as the clock that drives the
PLLs and the CPU. The nominal IRC frequency is 12 MHz. The IRC is trimmed to 1.5 %
accuracy for Tamb = 0 °C to 85 °C and 3% accuracy for Tamb = -40 °C to 0 °C and Tamb =
85 °C to 105 °C.
Upon power-up or any chip reset, the LPC436x use the IRC as the clock source. The boot
loader then configures the PLL1 to provide a 96 MHz clock for the core and PLL0USB or
PLL0AUDIO as needed if an external boot source is selected.
7.23.5 PLL0USB (for USB0)
PLL0 is a dedicated PLL for the USB0 High-speed controller.
PLL0 accepts an input clock frequency from an external oscillator in the range of 14 kHz
to 25 MHz. The input frequency is multiplied up to a high frequency with a Current
Controlled Oscillator (CCO). The CCO operates in the range of 4.3 MHz to 550 MHz.
7.23.6 PLL0AUDIO (for audio)
The audio PLL PLL0AUDIO is a general purpose PLL with a very small step size. This
PLL accepts an input clock frequency derived from an external oscillator or internal IRC.
The input frequency is multiplied up to a high frequency with a Current Controlled
Oscillator (CCO). A sigma-delta converter modulates the PLL divider ratios to obtain the
desired output frequency. The output frequency can be set as a multiple of the sampling
frequency fs to 32fs, 64fs, 128 fs, 256 fs, 384 fs, 512 fs and the sampling
frequency fs can range from 16 kHz to 192 kHz (16, 22.05, 32, 44.1, 48, 96,192) kHz.
Many other frequencies are possible as well using the integrated fractional divider.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
84 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7.23.7 System PLL1
The PLL1 accepts an input clock frequency from an external oscillator in the range of
1 MHz to 25 MHz. The input frequency is multiplied up to a high frequency with a Current
Controlled Oscillator (CCO). The multiplier can be an integer value from 1 to 32. The CCO
operates in the range of 156 MHz to 320 MHz. This range is possible through an
additional divider in the loop to keep the CCO within its frequency range while the PLL is
providing the desired output frequency. The output divider can be set to divide by 2, 4, 8,
or 16 to produce the output clock. Since the minimum output divider value is 2, it is
insured that the PLL output has a 50 % duty cycle. The PLL is turned off and bypassed
following a chip reset. After reset, software can enable the PLL. The program must
configure and activate the PLL, wait for the PLL to lock, and then connect to the PLL as a
clock source. The PLL settling time is 100 s.
7.23.8 Reset Generation Unit (RGU)
The RGU allows generation of independent reset signals for individual blocks and
peripherals on the LPC436x.
7.23.9 Power Management Controller (PMC)
The PMC controls the power to the cores, peripherals, and memories.
The LPC436x support the following power modes in order from highest to lowest power
consumption:
1. Active mode
2. Sleep mode
3. Power-down modes:
a. Deep-sleep mode
b. Power-down mode
c. Deep power-down mode
Active mode and sleep mode apply to the state of the core. In a dual-core system, either
core can be in active or sleep mode independently of the other core.
If the core is in Active mode, it is fully operational and can access peripherals and
memories as configured by software. If the core is in Sleep mode, it receives no clocks,
but peripherals and memories remain running.
Either core can enter sleep mode from active mode independently of the other core and
while the other core remains in active mode or is in sleep mode.
Power-down modes apply to the entire system. In the Power-down modes, both cores and
all peripherals except for peripherals in the always-on power domain are shut down.
Memories can remain powered for retaining memory contents as defined by the individual
power-down mode.
Either core in active mode can put the part into one of the three power down modes if the
core is enabled to do so. If both cores are enabled for putting the system into power-down,
then the system enters power-down only once both cores have received a WFI or WFE
instruction.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
85 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Wake-up from sleep mode is caused by an interrupt or event in the core’s NVIC. The
interrupt is captured in the NVIC and an event is captured in the Event router. Both cores
can wake up from sleep mode independently of each other.
Wake-up from the Power-down modes, Deep-sleep, Power-down, and Deep power-down,
is caused by an event on the WAKEUP pins or an event from the RTC or alarm timer.
When waking up from Deep power-down mode, the part resets and attempts to boot.
7.23.10 Power control
The LPC436x feature several independent power domains to control power to the core
and the peripherals (see Figure 8). The RTC and its associated peripherals (the alarm
timer, the CREG block, the OTP controller, the back-up registers, and the event router)
are located in the RTC power-domain. The main regulator or a battery supply can power
the RTC. A power selector switch ensures that the RTC block is always powered on.
LPC43xx
VDDIO
to I/O pads
to cores
VSS
REGULATOR
to memories,
peripherals,
oscillators,
PLLs
VDDREG
MAIN POWER DOMAIN
ULTRA LOW-POWER
REGULATOR
VBAT
to RTC
domain
peripherals
RESET
WAKEUP0/1/2/3
RESET/WAKE-UP
CONTROL
to RTC I/O
pads (Vps)
BACKUP REGISTERS
RTCX1
RTCX2
32 kHz
OSCILLATOR
ALARM
REAL-TIME CLOCK
ALWAYS-ON/RTC POWER DOMAIN
DAC
VDDA
VSSA
ADC
ADC POWER DOMAIN
OTP
VPP
OTP POWER DOMAIN
USB0_VDDA3V_DRIVER
USB0_VDDA3V3
USB0
USB0 POWER DOMAIN
002aag378
Fig 8.
Power domains
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
86 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7.23.11 Code security (Code Read Protection - CRP)
CRP enables different levels of security so that access to the on-chip flash and use of the
JTAG and ISP can be restricted. CRP is invoked by programming a specific pattern into a
dedicated flash location. IAP commands are not affected by CRP.
There are three levels of the Code Read Protection:
• In level CRP1, access to the chip via the JTAG is disabled. Partial flash updates are
allowed (excluding flash sector 0) using a limited set of the ISP commands. This level
is useful when CRP is required and flash field updates are needed. CRP1 does
prevent the user code from erasing all sectors.
• In level CRP2, access to the chip via the JTAG is disabled. Only a full flash erase and
update using a reduced set of the ISP commands is allowed.
• In level CRP3, any access to the chip via the JTAG pins or the ISP is disabled. This
mode also disables the ISP override using P2_7 pin. If necessary, the application
code must provide a flash update mechanism using the IAP calls or using the
reinvoke ISP command to enable flash update via USART0. See Table 5
CAUTION
If level three Code Read Protection (CRP3) is selected, no future factory testing can be
performed on the device.
7.24 Serial Wire Debug/JTAG
Debug and trace functions are integrated into the ARM Cortex-M4. Serial wire debug and
trace functions are supported in addition to a standard JTAG debug and parallel trace
functions. The ARM Cortex-M4 is configured to support up to eight breakpoints and four
watch points.
Remark: Serial Wire Debug is supported for the ARM Cortex-M4 only,
The ARM Cortex-M0 coprocessors support JTAG debug. A standard ARM
Cortex-compliant debugger can debug the ARM Cortex-M4 and the ARM Cortex-M0
cores separately or both cores simultaneously.
Remark: In order to debug the ARM Cortex-M0, release the M0 reset by software in the
RGU block.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
87 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
LPC43xx
TCK
TMS
TRST
TDI
TCK
TMS
TRST
TDI
ARM Cortex-M0
TDO
JTAG ID = 0x0BA0 1477
TDO
DBGEN
RESET
TCK ARM Cortex-M4
TMS
TRST
TDI
TDO
JTAG ID = 0x4BA0 0477
DBGEN = HIGH
RESET = HIGH
002aah448
Fig 9.
LPC436X
Product data sheet
Dual-core debug configuration
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
88 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
8. Limiting values
Table 7.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
Parameter
Conditions
Min
Max
Unit
VDD(REG)(3V3)
regulator supply voltage
(3.3 V)
on pin VDDREG
0.5
3.6
V
VDD(IO)
input/output supply
voltage
on pin VDDIO
0.5
3.6
V
VDDA(3V3)
analog supply voltage
(3.3 V)
on pin VDDA
0.5
3.6
V
VBAT
battery supply voltage
on pin VBAT
0.5
3.6
V
Vprog(pf)
polyfuse programming
voltage
on pin VPP
0.5
3.6
V
VI
input voltage
when VDD(IO) 2.4 V
0.5
5.5
V
ADC/DAC pins and digital I/O
pins configured for an analog
function
0.5
VDDA(3V3)
V
USB0 pins USB0_DP;
USB0_DM;USB0_VBUS
0.3
5.25
V
USB0 pins USB0_ID;
USB0_RREF
0.3
3.6
V
USB1 pins USB1_DP and
USB1_DM
0.3
5.25
V
[2]
5 V tolerant digital I/O pins
IDD
supply current
per supply pin
-
100
mA
ISS
ground current
per ground pin
-
100
mA
Ilatch
I/O latch-up current
(0.5VDD(IO)) < VI < (1.5VDD(IO));
-
100
mA
Tstg
storage temperature
65
+150
C
Ptot(pack)
total power dissipation
(per package)
based on package heat transfer,
not device power consumption
-
1.5
W
VESD
electrostatic discharge
voltage
human body model; all pins
-
2000
V
Tj < 125 C
[1]
[3]
[4]
The following applies to the limiting values:
a) Absolute maximum ratings state the extreme limits that the product can withstand without leading to irrecoverable failure. Failure
includes the loss of reliability and shorter lifetime of the device. Conditions for functional operation of the part are shown in Table 11
“Static characteristics”.
b) This product includes circuitry designed for the protection of its internal devices from the damaging effects of excessive static
charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum.
c) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
[2]
Including voltage on outputs in 3-state mode.
[3]
Dependent on package type.
[4]
Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
89 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
9. Thermal characteristics
The average chip junction temperature, Tj (C), can be calculated using the following
equation:
T j = T amb + P D R th j – a
(1)
• Tamb = ambient temperature (C),
• Rth(j-a) = the package junction-to-ambient thermal resistance (C/W)
• PD = sum of internal and I/O power dissipation
The internal power dissipation is the product of IDD and VDD. The I/O power dissipation of
the I/O pins is often small and many times can be negligible. However it can be significant
in some applications.
Table 8.
Thermal characteristics
Symbol
Parameter
Conditions Min
Typ
Max
Unit
Tj(max)
maximum junction
temperature
-
-
125
C
Table 9.
-
Thermal resistance (LQFP packages)
Symbol Parameter
Thermal resistance in C/W
±15 %
Conditions
LQFP144
Rth(j-a)
Rth(j-c)
thermal resistance from JEDEC (4.5 in 4 in); still 38
junction to ambient
air
31
Single-layer (4.5 in 3 in); 50
still air
39
thermal resistance from junction to case
11
Table 10.
Thermal resistance value (BGA packages)
Symbol
Parameter
Rth(j-a)
thermal resistance from JEDEC (4.5 in 4 in); 29
junction to ambient
still air
Conditions
10
Thermal resistance in C/W ±15 %
LBGA256
8-layer (4.5 in 3 in);
still air
Rth(j-c)
LPC436X
Product data sheet
LQFP208
thermal resistance from junction to case
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
TFBGA100
46
24
37
14
11
© NXP Semiconductors N.V. 2016. All rights reserved.
90 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
10. Static characteristics
Table 11. Static characteristics
Tamb = 40 C to +105 C, unless otherwise specified.
Symbol
Parameter
Min
Typ[1]
Max
Unit
[17]
2.4
-
3.6
V
[2]
2.4
-
3.6
V
Conditions
Supply pins
VDD(IO)
input/output supply
voltage
VDD(REG)(3V3)
regulator supply voltage
(3.3 V)
VDDA(3V3)
analog supply voltage
(3.3 V)
on pin VDDA
2.4
-
3.6
V
on pins
USB0_VDDA3V3_
DRIVER and
USB0_VDDA3V3
3.0
3.3
3.6
V
battery supply voltage
[2]
2.4
-
3.6
V
Vprog(pf)
polyfuse programming
voltage
on pin VPP (for OTP)
[3]
2.7
-
3.6
V
Iprog(pf)
polyfuse programming
current
on pin VPP; OTP
programming time
1.6 ms
-
-
30
mA
IDD(REG)(3V3)
regulator supply current Active mode; ARM
(3.3 V)
Cortex-M0 core in reset;
code
-
10
-
mA
VBAT
while(1){}
executed from RAM; all
peripherals disabled;
PLL1 enabled
IDD(REG)(3V3)
CCLK = 12 MHz
[4]
CCLK = 60 MHz
[4]
28
-
mA
CCLK = 120 MHz
[4]
-
51
-
mA
CCLK = 180 MHz
[4]
-
74
-
mA
CCLK = 204 MHz
[4]
-
83
-
mA
[4][5]
-
8.8
-
mA
deep-sleep mode
[4]
-
145
-
A
power-down mode
[4]
-
23
-
A
[4][6]
-
0.05
-
A
[4]
-
3.0
-
A
[7]
-
0.1
nA
regulator supply current after WFE/WFI instruction
(3.3 V)
executed from RAM; all
peripherals disabled;
ARM Cortex-M0 core in
reset
sleep mode
deep power-down
mode
deep power-down
mode; VBAT floating
IBAT
LPC436X
Product data sheet
battery supply current
VBAT = 3.0 V;
VDD(REG)(3V3) = 3.3 V
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
91 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 11. Static characteristics …continued
Tamb = 40 C to +105 C, unless otherwise specified.
Symbol
IBAT
Parameter
battery supply current
Conditions
VDD(REG)(3V3) = 3.3 V;
VBAT = 3.6 V
deep-sleep mode
IBAT
IDD(IO)
IDDA
battery supply current
I/O supply current
Analog supply current
Min
Typ[1]
Max
Unit
-
1.5
-
A
-
1.5
-
A
-
1.5
-
A
-
3.0
-
A
1.5
-
A
< 0.1
-
A
[8]
power-down mode
[8]
deep power-down
mode
[8]
Deep power-down mode;
RTC running;
VDD(REG) = VDDA =
VDDIO = 0 V;
VDD(REG)(3V3) =
VBAT = 3.3 V
-
deep sleep mode
-
power-down mode
-
< 0.1
-
A
deep power-down mode
-
< 0.1
-
A
[10]
-
0.4
-
power-down mode
[10]
-
0.4
-
deep power-down
mode
[10]
-
0.007
-
on pin VDDA;
A
deep sleep mode
A
A
RESET pin
VIH
HIGH-level input
voltage
[9]
0.8 (Vps 0.35)
5.5
VIL
LOW-level input voltage
[9]
0.5
0.3 (Vps V
0.1)
Vhys
hysteresis voltage
[9]
0.05 (Vps 0.35)
-
-
V
V
Standard I/O pins - normal drive strength
CI
input capacitance
-
-
2
pF
ILL
LOW-level leakage
current
VI = 0 V; on-chip pull-up
resistor disabled
-
3
-
nA
ILH
HIGH-level leakage
current
VI = VDD(IO); on-chip
pull-down resistor
disabled
-
3
-
nA
VI = 5 V; Tamb = 25 °C
-
0.5
-
nA
VI = 5 V; Tamb = 105 °C
-
40
-
nA
IOZ
OFF-state output
current
VO = 0 V to VDD(IO);
on-chip pull-up/down
resistors disabled;
absolute value
-
3
-
nA
VI
input voltage
pin configured to provide
a digital function;
0
-
5.5
V
VDD(IO) 2.4 V
VDD(IO) = 0 V
VO
LPC436X
Product data sheet
output voltage
output active
0
-
3.6
V
0
-
VDD(IO)
V
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
92 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 11. Static characteristics …continued
Tamb = 40 C to +105 C, unless otherwise specified.
Min
Typ[1]
Max
Unit
HIGH-level input
voltage
0.7
VDD(IO)
-
5.5
V
VIL
LOW-level input voltage
0.5
-
0.3
VDD(IO)
V
Vhys
hysteresis voltage
0.1
VDD(IO)
-
-
V
VOH
HIGH-level output
voltage
IOH = 6 mA
VDD(IO)
0.4
-
-
V
VOL
LOW-level output
voltage
IOL = 6 mA
-
-
0.4
V
IOH
HIGH-level output
current
VOH = VDD(IO) 0.4 V
6
-
-
mA
IOL
LOW-level output
current
VOL = 0.4 V
6
-
-
mA
IOHS
HIGH-level short-circuit drive HIGH; connected to
output current
ground
[11]
-
-
86.5
mA
IOLS
LOW-level short-circuit
output current
drive LOW; connected to
VDD(IO)
[11]
-
-
76.5
mA
Ipd
pull-down current
VI = 5 V
[13]
-
93
-
A
-
62
-
A
-
10
-
A
Symbol
Parameter
VIH
Conditions
[14]
[15]
Ipu
pull-up current
VI = 0 V
[13]
[14]
[15]
VDD(IO) < VI 5 V
Rs
series resistance
on I/O pins with analog
function; analog function
enabled
200
I/O pins - high drive strength
CI
input capacitance
-
-
5.2
pF
ILL
LOW-level leakage
current
VI = 0 V; on-chip pull-up
resistor disabled
-
3
-
nA
IOZ
OFF-state output
current
VO = 0 V to VDD(IO);
on-chip pull-up/down
resistors disabled;
absolute value
-
3
-
nA
VI
input voltage
pin configured to provide
a digital function;
VDD(IO) 2.4 V
0
-
5.5
V
VDD(IO) = 0 V
0
-
3.6
V
0
-
VDD(IO)
V
VO
output voltage
VIH
HIGH-level input
voltage
0.7
VDD(IO)
-
5.5
V
VIL
LOW-level input voltage
0.5
-
0.3
VDD(IO)
V
LPC436X
Product data sheet
output active
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
93 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 11. Static characteristics …continued
Tamb = 40 C to +105 C, unless otherwise specified.
Symbol
Parameter
Vhys
hysteresis voltage
Ipd
pull-down current
Min
Typ[1]
Max
Unit
0.1
VDD(IO)
-
-
V
-
62
-
A
-
62
-
A
-
10
-
A
VI = VDD(IO); on-chip
pull-down resistor
disabled
-
3
-
nA
VI = 5 V; Tamb = 25 °C
-
0.6
-
nA
Conditions
VI = VDD(IO)
[13]
[14]
[15]
Ipu
pull-up current
VI = 0 V
[13]
[14]
[15]
VDD(IO) < VI 5 V
I/O pins - high drive strength: standard drive mode
ILH
HIGH-level leakage
current
VI = 5 V; Tamb = 105 °C
-
65
-
nA
IOH
HIGH-level output
current
VOH = VDD(IO) 0.4 V
4
-
-
mA
IOL
LOW-level output
current
VOL = 0.4 V
4
-
-
mA
IOHS
HIGH-level short-circuit drive HIGH; connected to
output current
ground
[11]
-
-
32
mA
IOLS
LOW-level short-circuit
output current
[11]
-
-
32
mA
VI = VDD(IO); on-chip
pull-down resistor
disabled
-
3
-
nA
VI = 5 V; Tamb = 25 °C
-
0.7
-
nA
VI = 5 V; Tamb = 105 °C
-
70
-
nA
drive LOW; connected to
VDD(IO)
I/O pins - high drive strength: medium drive mode
ILH
HIGH-level leakage
current
IOH
HIGH-level output
current
VOH = VDD(IO) 0.4 V
8
-
-
mA
IOL
LOW-level output
current
VOL = 0.4 V
8
-
-
mA
IOHS
HIGH-level short-circuit drive HIGH; connected to
output current
ground
[11]
-
-
65
mA
IOLS
LOW-level short-circuit
output current
[11]
-
-
63
mA
VI = VDD(IO); on-chip
pull-down resistor
disabled
-
3
-
nA
VI = 5 V; Tamb = 25 °C
-
0.6
-
nA
drive LOW; connected to
VDD(IO)
I/O pins - high drive strength: high drive mode
ILH
IOH
LPC436X
Product data sheet
HIGH-level leakage
current
HIGH-level output
current
VI = 5 V; Tamb = 105 °C
-
63
-
nA
VOH = VDD(IO) 0.4 V
14
-
-
mA
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
94 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 11. Static characteristics …continued
Tamb = 40 C to +105 C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
IOL
LOW-level output
current
VOL = 0.4 V
14
-
-
mA
IOHS
HIGH-level short-circuit drive HIGH; connected to
output current
ground
[11]
-
-
113
mA
IOLS
LOW-level short-circuit
output current
[11]
-
-
110
mA
VI = VDD(IO); on-chip
pull-down resistor
disabled
-
3
-
nA
drive LOW; connected to
VDD(IO)
I/O pins - high drive strength: ultra-high drive mode
ILH
HIGH-level leakage
current
VI = 5 V; Tamb = 25 °C
-
0.6
-
nA
VI = 5 V; Tamb = 105 °C
-
63
-
nA
IOH
HIGH-level output
current
VOH = VDD(IO) 0.4 V
20
-
-
mA
IOL
LOW-level output
current
VOL = 0.4 V
20
-
-
mA
IOHS
HIGH-level short-circuit drive HIGH; connected to
output current
ground
[11]
-
-
165
mA
IOLS
LOW-level short-circuit
output current
[11]
-
-
156
mA
-
-
2
pF
drive LOW; connected to
VDD(IO)
I/O pins - high-speed
CI
input capacitance
ILL
LOW-level leakage
current
VI = 0 V; on-chip pull-up
resistor disabled
-
3
-
nA
ILH
HIGH-level leakage
current
VI = VDD(IO); on-chip
pull-down resistor
disabled
-
3
-
nA
VI = 5 V; Tamb = 25 °C
-
0.5
-
nA
VI = 5 V; Tamb = 105 °C
-
40
-
nA
-
3
-
nA
VDD(IO) 2.4 V
0
-
5.5
V
VDD(IO) = 0 V
0
-
3.6
V
IOZ
OFF-state output
current
VO = 0 V to VDD(IO);
on-chip pull-up/down
resistors disabled;
absolute value
VI
input voltage
pin configured to provide
a digital function;
VO
output voltage
0
-
VDD(IO)
V
VIH
HIGH-level input
voltage
0.7
VDD(IO)
-
5.5
V
VIL
LOW-level input voltage
0.5
-
0.3
VDD(IO)
V
Vhys
hysteresis voltage
0.1
VDD(IO)
-
-
V
LPC436X
Product data sheet
output active
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
95 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 11. Static characteristics …continued
Tamb = 40 C to +105 C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
VOH
HIGH-level output
voltage
IOH = 8 mA
VDD(IO)
0.4
-
-
V
VOL
LOW-level output
voltage
IOL = 8 mA
-
-
0.4
V
IOH
HIGH-level output
current
VOH = VDD(IO) 0.4 V
8
-
-
mA
IOL
LOW-level output
current
VOL = 0.4 V
8
-
-
mA
IOHS
HIGH-level short-circuit drive HIGH; connected to
output current
ground
[11]
-
-
86
mA
IOLS
LOW-level short-circuit
output current
drive LOW; connected to
VDD(IO)
[11]
-
-
76
mA
Ipd
pull-down current
VI = VDD(IO)
[13]
-
62
-
A
-
62
-
A
-
0
-
A
[14]
[15]
Ipu
pull-up current
VI = 0 V
[13]
[14]
[15]
VDD(IO) < VI 5 V
Open-drain I2C0-bus pins
VIH
HIGH-level input
voltage
0.7
VDD(IO)
-
-
V
VIL
LOW-level input voltage
0.5
0.14
0.3
VDD(IO)
V
Vhys
hysteresis voltage
0.1
VDD(IO)
-
-
V
VOL
LOW-level output
voltage
IOLS = 3 mA
-
-
0.4
V
ILI
input leakage current
VI = VDD(IO)
-
4.5
-
A
-
-
10
A
[12]
VI = 5 V
Oscillator pins
Vi(XTAL1)
input voltage on pin
XTAL1
0.5
-
1.2
V
Vo(XTAL2)
output voltage on pin
XTAL2
0.5
-
1.2
V
Cio
input/output
capacitance
-
-
0.8
pF
0
-
5.25
V
[16]
USB0 pins[17]
VI
input voltage
on pins USB0_DP;
USB0_DM; USB0_VBUS
VDD(IO) 2.4 V
VDD(IO) = 0 V
Rpd
LPC436X
Product data sheet
pull-down resistance
on pin USB0_VBUS
0
-
3.6
V
48
64
80
k
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
96 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 11. Static characteristics …continued
Tamb = 40 C to +105 C, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
VIC
common-mode input
voltage
high-speed mode
50
200
500
mV
full-speed/low-speed
mode
800
-
2500
mV
chirp mode
50
-
600
mV
100
400
1100
mV
[17]
-
-
10
A
[18]
-
-
5.25
V
differential input voltage
Vi(dif)
USB1 pins
(USB1_DP/USB1_DM)[17]
IOZ
OFF-state output
current
0 V < VI < 3.3 V
VBUS
bus supply voltage
VDI
differential input
sensitivity voltage
(D+) (D)
0.2
-
-
V
VCM
differential common
mode voltage range
includes VDI range
0.8
-
2.5
V
Vth(rs)se
single-ended receiver
switching threshold
voltage
0.8
-
2.0
V
VOL
LOW-level output
voltage for
low-/full-speed
RL of 1.5 k to 3.6 V
-
-
0.18
V
VOH
HIGH-level output
voltage (driven) for
low-/full-speed
RL of 15 k to GND
2.8
-
3.5
V
Ctrans
transceiver capacitance pin to GND
ZDRV
driver output
with 33 series resistor;
impedance for driver
steady state drive
which is not high-speed
capable
[19]
-
-
20
pF
36
-
44.1
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.
[2]
The recommended operating condition for the battery supply is VDD(REG)(3V3) > VBAT + 0.2 V. Special conditions for VDD(REG)(3V3) apply
when writing to the flash and EEPROM. See Table 16 and Table 15.
[3]
Pin VPP should either be not connected (when OTP does not need to be programmed) or tied to pins VDDIO and VDDREG to ensure
the same ramp-up time for both supply voltages.
[4]
VDD(REG)(3V3) = 3.3 V; VDD(IO) = 3.3 V; Tamb = 25 C.
[5]
PLL1 disabled; IRC running; CCLK = 12 MHz.
[6]
VBAT = 3.6 V.
[7]
Tamb = -40 C to +105 C; VDD(IO) = VDDA = 3.6 V; over entire frequency range CCLK = 12 MHz to 204 MHz; in active mode, sleep
mode; deep-sleep mode, power-down mode, and deep power-down mode.
[8]
On pin VBAT; Tamb = 25 C.
[9]
Vps corresponds to the output of the power switch (see Figure 8) which is determined by the greater of VBAT and VDD(Reg)(3V3).
[10] VDDA(3V3) = 3.3 V; Tamb = 25 C.
[11] Allowed as long as the current limit does not exceed the maximum current allowed by the device.
[12] To VSS.
[13] The values specified are simulated and absolute values.
[14] The weak pull-up resistor is connected to the VDD(IO) rail and pulls up the I/O pin to the VDD(IO) level.
[15] The input cell disables the weak pull-up resistor when the applied input voltage exceeds VDD(IO).
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
97 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
[16] The parameter value specified is a simulated value excluding bond capacitance.
[17] For USB operation 3.0 V VDD((IO) 3.6 V. Guaranteed by design.
[18] VDD(IO) present.
[19] Includes external resistors of 33 1 % on D+ and D.
10.1 Power consumption
aaa-013450
100
IDD(REG)(3V3)
(mA)
204 MHz
80
180 MHz
60
120 MHz
40
60 MHz
20
12 MHz
0
2.2
2.4
2.6
2.8
3
3.2
3.4
VDD(REG)(3V3) (V)
3.6
Conditions: Tamb = 25 C; executing code while (1){} from SRAM; M0 core in reset; system PLL
enabled; IRC enabled; all peripherals disabled; all peripheral clocks disabled.
Fig 10. Typical supply current versus regulator supply voltage VDD(REEG)(3V3) in active
mode
aaa-013449
100
IDD(REG)(3V3)
(mA)
204 MHz
80
180 MHz
60
120 MHz
40
60 MHz
20
12 MHz
0
-40
-20
0
20
40
60
80
100
temperature (°C)
120
Conditions: VDD(REG)(3V3) = 3.3 V; executing code while (1){} from SRAM; M0 core in reset; system
PLL enabled; IRC enabled; all peripherals disabled; all peripheral clocks disabled.
Fig 11. Typical supply current versus temperature in active mode
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
98 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
aaa-013452
100
IDD(REG)(3V3)
(mA)
(mA)
+105 °C
C
+90 °C
C
+25 °C
C
0 °C
C
-40 °C
C
80
60
40
20
0
12
36
60
84
108
132
156
180
frequency (MHz)
204
Conditions: active mode entered executing code while (1){} from SRAM; M0 core in reset;
VDD(REG)(3V3) = 3.3 V; system PLL enabled; IRC enabled; all peripherals disabled; all peripheral
clocks disabled.
Fig 12. Typical supply current versus core frequency in active mode; code executed from
SRAM
aaa-013047
20
IDD(REG)(3V3)
(mA)
15
10
5
0
-40
-20
0
20
40
60
80
100
temperature (°C)
120
Conditions: VDD(REG)(3V3) = 3.3 V; internal pull-up resistors disabled; M0 core in reset; system PLL
disabled; IRC enabled; all peripherals disabled; all peripheral clocks disabled. CCLK = 12 MHz.
Fig 13. Typical supply current versus temperature in sleep mode
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
99 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
002aah410
1.6
IDD(REG)(3V3)
(μA) (mA)
002aah412
300
IDD(REG)(3V3)
(μA)(μA)
240
1.2
180
0.8
120
0.4
60
0
-40
0
40
80
temperature (°C)
0
-40
120
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V.
40
80
temperature (°C)
120
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V.
Fig 14. Typical supply current versus temperature in
Deep-sleep mode
Fig 15. Typical supply current versus temperature in
Power-down mode
002aah424
25
IDD(REG)(3V3)/IBAT
(μA)
0
002aah415
30
IBAT
IBAT
(μA)
25
20
20
15
15
10
IIBAT
BAT
IDD(REG)(3V3)
10
5
0
-40
5
-20
0
20
40
60
80 100
temperature (°C)
120
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V. VBAT =
VDD(REG)(3V3) + 0.4 V.
Fig 16. Typical supply current versus temperature in
Deep power-down mode
LPC436X
Product data sheet
0
-40
-20
0
20
40
60
80 100
temperature (°C)
120
Conditions: VBAT = 3.6 V. VDD(REG)(3V3) not present.
Fig 17. Typical battery supply current versus
temperature
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
100 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
002aah379
100
IBAT
(μA)
80
60
40
20
0
-0.4
-0.2
0
0.2
0.4
VBAT - VDD(REG)(3V3) (V)
0.6
Conditions: VDD(REG)(3V3) = 3.0 V; VBAT = 2.6 V to 3.6 V; CCLK = 12 MHz.
Remark: The recommended operating condition for the battery supply is
VDD(REG)(3V3) > VBAT + 0.2 V.
Fig 18. Typical battery supply current in Active mode
10.2 Peripheral power consumption
The typical power consumption at T = 25 C for each individual peripheral is measured as
follows:
1. Enable all branch clocks and measure the current IDD(REG)(3V3).
2. Disable the branch clock to the peripheral to be measured and keep all other branch
clocks enabled.
3. Calculate the difference between measurement 1 and 2. The result is the peripheral
power consumption.
Table 12.
Peripheral power consumption
Peripheral
LPC436X
Product data sheet
Branch clock
IDD(REG)(3V3) in mA
Branch clock
frequency = 48 MHz
Branch clock
frequency = 96 MHz
M0 subsystem core CLK_PERIPH_CORE
2.4
4.8
M0 coprocessor
CLK_M4_M0APP
3.3
6.6
I2C1
CLK_APB3_I2C1
0.01
0.01
I2C0
CLK_APB1_I2C0
< 0.01
0.02
DAC
CLK_APB3_DAC
0.01
0.02
ADC0
CLK_APB3_ADC0
0.07
0.07
ADC1
CLK_APB3_ADC1
0.07
0.07
CAN0
CLK_APB3_CAN0
0.17
0.17
CAN1
CLK_APB1_CAN1
0.16
0.15
MOTOCON
CLK_APB1_MOTOCON
0.04
0.04
I2S
CLK_APB1_I2S
0.09
0.08
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
101 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 12.
Peripheral power consumption
Peripheral
LPC436X
Product data sheet
Branch clock
IDD(REG)(3V3) in mA
Branch clock
frequency = 48 MHz
Branch clock
frequency = 96 MHz
SPIFI
CLK_SPIFI,
CLK_M4_SPIFI
1.14
2.29
GPIO
CLK_M4_GPIO
0.72
1.43
LCD
CLK_M4_LCD
0.91
1.82
ETHERNET
CLK_M4_ETHERNET
1.06
2.15
UART0
CLK_M4_UART0,
CLK_APB0_UART0
0.24
0.43
UART1
CLK_M4_UART1,
CLK_APB0_UART1
0.24
0.43
UART2
CLK_M4_UART2,
CLK_APB2_UART2
0.26
0.5
UART3
CLK_M4_USART3,
CLK_APB2_UART3
0.27
0.45
TIMER0
CLK_M4_TIMER0
0.08
0.15
TIMER1
CLK_M4_TIMER1
0.09
0.15
TIMER2
CLK_M4_TIMER2
0.1
0.19
TIMER3
CLK_M4_TIMER3
0.08
0.16
SDIO
CLK_M4_SDIO,
CLK_SDIO
0.66
1.17
SCTimer/PWM
CLK_M4_SCT
0.66
1.3
SSP0
CLK_M4_SSP0,
CLK_APB0_SSP0
0.13
0.23
SSP1
CLK_M4_SSP1,
CLK_APB2_SSP1
0.14
0.27
DMA
CLK_M4_DMA
1.81
3.61
WWDT
CLK_M4_WWDT
0.03
0.09
QEI
CLK_M4_QEI
0.28
0.55
USB0
CLK_M4_USB0,
CLK_USB0
1.9
3.9
USB1
CLK_M4_USB1,
CLK_USB1
3.02
5.69
RITIMER
CLK_M4_RITIMER
0.05
0.1
EMC
CLK_M4_EMC,
CLK_M4_EMC_DIV
3.94
7.95
SCU
CLK_M4_SCU
0.1
0.21
CREG
CLK_M4_CREG
0.35
0.7
Flash bank A
CLK_M4_FLASHA
1.47
2.97
Flash bank B
CLK_M4_FLASHB
1.4
2.84
SGPIO
CLK_PERIPH_SGPIO
0.1
0.17
SPI
CLK_SPI
0.07
0.11
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
102 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
10.3 Electrical pin characteristics
002aah368
3.6
VOH
(V)
002aah359
3.6
VOH
(V)
-40 °C
+25 °C
+85 °C
+105 °C
3.2
2.8
3.2
-40 °C
+25 °C
+85 °C
+105 °C
2.8
2.4
2.4
2
2
0
16
32
48
64
80
IOH (mA)
96
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V.
Product data sheet
6
12
18
24
30
IOH (mA)
36
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V.
Fig 19. Standard I/O pins; typical LOW level output
current IOL versus LOW level output voltage
VOL
LPC436X
0
Fig 20. Standard I/O pins; typical HIGH level output
voltage VOH versus HIGH level output current
IOH
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
103 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
002aah360
15
-40 °C
+25 °C
+85 °C
+105 °C
IOL
(mA)
12
002aah361
25
-40 °C
+25 °C
+85 °C
+105 °C
IOL
(mA)
20
9
15
6
10
3
5
0
0
0
0.1
0.2
0.3
0.4
0.5
VOL (V)
0.6
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; normal-drive;
EHD = 0x0.
0
-40 °C
+25 °C
+85 °C
+105 °C
32
0.2
0.3
0.4
0.5
VOL (V)
0.6
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V;
medium-drive; EHD = 0x1.
002aah362
40
IOL
(mA)
0.1
002aah363
60
-40 °C
+25 °C
+85 °C
+105 °C
IOL
(mA)
45
24
30
16
15
8
0
0
0
0.1
0.2
0.3
0.4
0.5
VOL (V)
0.6
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; high-drive;
EHD = 0x2.
0
0.1
0.2
0.3
0.4
0.5
VOL (V)
0.6
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; ultra
high-drive; EHD = 0x3.
Fig 21. High-drive pins; typical LOW level output current IOL versus LOW level output voltage VOL
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
104 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
002aah364
3.6
VOH
(V)
002aah367
3.6
VOH
(V)
-40 °C
+25 °C
+85 °C
+105 °C
3.2
2.8
-40 °C
+25 °C
+85 °C
+105 °C
3.2
2.8
2.4
2.4
2
2
0
4
8
12
16
20
IOH (mA)
24
0
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; normal-drive;
EHD = 0x0.
16
24
32
40
IOH (mA)
48
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V;
medium-drive; EHD = 0x1.
002aah368
3.6
VOH
(V)
8
002aah369
3.6
VOH
(V)
-40 °C
+25 °C
+85 °C
+105 °C
3.2
2.8
-40 °C
+25 °C
+85 °C
+105 °C
3.2
2.8
2.4
2.4
2
2
0
16
32
48
64
80
IOH (mA)
96
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; high-drive;
EHD = 0x2.
0
20
40
60
80
100
IOH (mA)
120
Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; ultra
high-drive; EHD = 0x3.
Fig 22. High-drive pins; typical HIGH level output voltage VOH versus HGH level output current IOH
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
105 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
002aah422
20
IIpu
pu
(μA)
0
+105 °C
C
+25 °C
C
-40 °C
C
-20
-40
-60
-80
0
1
2
3
4
VI (V)
5
Conditions: VDD(IO) = 3.3 V. Simulated data over process and temperature.
Fig 23. Pull-up current Ipu versus input voltage VI
002aah418
120
IIpd
pd
(μA)
-40 °C
C
+25 °C
C
+105 °C
C
90
60
30
0
0
1
2
3
4
VI (V)
5
Conditions: VDD(IO) = 3.3 V. Simulated data over process and temperature.
Fig 24. Pull-down current Ipd versus input voltage VI
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
106 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
10.4 BOD and band gap static characteristics
Table 13. BOD static characteristics[1]
Tamb = 25 C; simulated values for nominal processing.
Symbol
Parameter
Conditions
Min
Vth
threshold voltage
interrupt level 2
Typ
Max
Unit
assertion
-
2.95
-
V
de-assertion
-
3.03
-
V
assertion
-
3.05
-
V
de-assertion
-
3.13
-
V
assertion
-
2.1
-
V
de-assertion
-
2.18
-
V
assertion
-
2.2
-
V
de-assertion
-
2.28
-
V
interrupt level 3
reset level 2
reset level 3
[1]
Interrupt and reset levels are selected by writing to the BODLV1/2 bits in the control register CREGE0, see
the LPC43xx user manual.
Table 14. Band gap characteristics
VDDA(3V3) over specified ranges; Tamb = 40 C to +105 C; unless otherwise specified
Symbol
Vref(bg)
[1]
LPC436X
Product data sheet
Parameter
band gap reference voltage
[1]
Min
Typ
Max
Unit
0.707
0.745
0.783
mV
Based on characterization, not tested in production.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
107 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11. Dynamic characteristics
11.1 Flash/EEPROM memory
Table 15. Flash characteristics
Tamb = 40 C to +105 C, unless otherwise specified. VDD(REG)(3V3) = 2.4 V to 3.6 V for read
operations; VDD(REG)(3V3) = 2.7 V to 3.6 V for erase/program operations.
Symbol
Parameter
Conditions
Nendu
endurance
sector erase/program
retention time
tret
ter
erase time
tprog
programming
time
Min
Typ
Max
Unit
10000
-
-
cycles
page erase/program; page
in large sector
1000
-
-
cycles
page erase/program; page
in small sector
10000
-
-
cycles
powered
10
-
-
years
unpowered
10
-
-
years
page, sector, or multiple
consecutive sectors
-
100
-
ms
-
1
-
ms
[1]
[2]
[1]
Number of erase/program cycles.
[2]
Programming times are given for writing 512 bytes from RAM to the flash. Data must be written to the flash
in blocks of 512 bytes.
Table 16. EEPROM characteristics
Tamb = 40 C to +105 C; VDD(REG)(3V3) = 2.7 V to 3.6 V.
Symbol
Parameter
fclk
clock frequency
Nendu
endurance
tret
retention time
access time
ta
twait
[1]
wait time
Conditions
Min
Typ
Max
Unit
800
1500
1600
kHz
100 000
-
-
cycles
Tamb = 40 C to +85 C
20
-
-
years
85 C < Tamb 105 C
10
-
-
years
read
-
120
-
ns
erase/program;
fclk = 1500 kHz
-
1.99
-
ms
erase/program;
fclk = 1600 kHz
-
1.87
-
ms
read; RPHASE1
[1]
70
-
-
ns
read; RPHASE2
[1]
35
-
-
ns
write; PHASE1
[1]
20
-
-
ns
write; PHASE2
[1]
40
-
-
ns
write; PHASE3
[1]
10
-
-
ns
See the LPC43xx user manual how to program the wait states for the different read (RPHASEx) and erase/program phases (PHASEx)
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
108 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11.2 Wake-up times
Table 17.
Dynamic characteristic: Wake-up from Deep-sleep, Power-down, and Deep
power-down modes
Tamb = 40 C to +105 C
Symbol Parameter
twake
Conditions
Typ[1]
Min
Max
Unit
3 Tcy(clk) 5 Tcy(clk) -
ns
from Deep-sleep and
Power-down mode
12
51
-
s
from Deep power-down mode
-
200
-
μs
after reset
-
200
-
μs
[2]
wake-up time from Sleep mode
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
[2]
Tcy(clk) = 1/CCLK with CCLK = CPU clock frequency.
11.3 External clock for oscillator in slave mode
Remark: The input voltage on the XTAL1/2 pins must be 1.2 V (see Table 11). For
connecting the oscillator to the XTAL pins, also see Section 13.2 and Section 13.4.
Table 18. Dynamic characteristic: external clock
Tamb = 40 C to +105 C; VDD(IO) over specified ranges.[1]
Symbol Parameter
Conditions
Min
Max
Unit
fosc
oscillator frequency
1
25
MHz
Tcy(clk)
clock cycle time
40
1000
ns
tCHCX
clock HIGH time
Tcy(clk) 0.4
Tcy(clk) 0.6
ns
tCLCX
clock LOW time
Tcy(clk) 0.4
Tcy(clk) 0.6
ns
[1]
Parameters are valid over operating temperature range unless otherwise specified.
tCHCX
tCLCX
Tcy(clk)
002aag698
Fig 25. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
109 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11.4 Crystal oscillator
Table 19. Dynamic characteristic: oscillator
Tamb = 40 C to +105 C; VDD(IO) over specified ranges; 2.4 V VDD(REG)(3V3) 3.6 V.[1]
Symbol
Parameter
Conditions
Low-frequency mode (1-20
tjit(per)
Typ[2]
Max
Unit
MHz)[5]
period jitter time
High-frequency mode (20 - 25
tjit(per)
Min
[3][4]
5 MHz crystal
-
13.2
-
ps
10 MHz crystal
-
6.6
-
ps
15 MHz crystal
-
4.8
-
ps
-
4.3
-
ps
-
3.7
-
ps
MHz)[6]
period jitter time
[3][4]
20 MHz crystal
25 MHz crystal
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
[3]
Indicates RMS period jitter.
[4]
PLL-induced jitter is not included.
[5]
Select HF = 0 in the XTAL_OSC_CTRL register.
[6]
Select HF = 1 in the XTAL_OSC_CTRL register.
11.5 IRC oscillator
Table 20. Dynamic characteristic: IRC oscillator
2.4 V VDD(REG)(3V3) 3.6 V
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
fosc(RC)
internal RC
oscillator
frequency
-40 C Tamb 0 C
12.0 - 3 %
12.0
12.0 + 3 %
MHz
0 C Tamb 85 C
12.0 - 1.5 %
12.0
12.0 + 1.5 %
MHz
85 C Tamb 105 C
12.0 - 3 %
12.0
12.0 + 3 %
MHz
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
11.6 RTC oscillator
See Section 13.3 for connecting the RTC oscillator to an external clock source.
Table 21. Dynamic characteristic: RTC oscillator
Tamb = 40 C to +105 C; 2.4 V VDD(REG)(3V3) 3.6 V or 2.4 V VBAT 3.6 V[1]
LPC436X
Product data sheet
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
fi
input frequency
-
-
32.768
-
kHz
ICC(osc)
oscillator supply
current
280
800
nA
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply
voltages.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
110 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11.7 GPCLKIN
Table 22. Dynamic characteristic: GPCLKIN
Tamb = 25 C; 2.4 V VDD(REG)(3V3) 3.6 V
Symbol
Parameter
Min
Typ
Max
Unit
GP_CLKIN
input frequency
-
-
25
MHz
11.8 I/O pins
Table 23. Dynamic characteristic: I/O pins[1]
Tamb = 40 C to +85 C; 2.7 V VDD(IO) 3.6 V.
Symbol Parameter
Conditions
Min
Typ
Max Unit
Standard I/O pins - normal drive strength
tr
rise time
pin configured as output; EHS = 1
[2][3]
1.0
-
2.5
ns
tf
fall time
pin configured as output; EHS = 1
[2][3]
0.9
-
2.5
ns
pin configured as output; EHS = 0
[2][3]
1.9
-
4.3
ns
pin configured as output; EHS = 0
[2][3]
1.9
-
4.0
ns
tr
tf
rise time
fall time
tr
rise time
pin configured as input
[4]
0.3
-
1.3
ns
tf
fall time
pin configured as input
[4]
0.2
-
1.2
ns
I/O pins - high drive strength
tr
rise time
pin configured as output; standard
drive mode (EHD = 0x0)
[2][5]
4.3
-
7.9
ns
tf
fall time
pin configured as output; standard
drive mode (EHD = 0x0)
[2][5]
4.7
-
8.7
ns
tr
rise time
pin configured as output; medium
drive mode (EHD = 0x1)
[2][5]
3.2
-
5.7
ns
tf
fall time
pin configured as output; medium
drive mode (EHD = 0x1)
[2][5]
3.2
-
5.5
ns
tr
rise time
pin configured as output; high drive
mode (EHD = 0x2)
[2][5]
2.9
-
4.9
ns
tf
fall time
pin configured as output; high drive
mode (EHD = 0x2)
[2][5]
2.5
-
3.9
ns
tr
rise time
pin configured as output; ultra-high
drive mode (EHD = 0x3)
[2][5]
2.8
-
4.7
ns
tf
fall time
pin configured as output; ultra-high
drive mode (EHD = 0x3)
[2][5]
2.4
-
3.4
ns
tr
rise time
pin configured as input
[4]
0.3
-
1.3
ns
pin configured as input
[4]
0.2
-
1.2
ns
pin configured as output; EHS = 1
[2][3]
350
-
670
ps
pin configured as output; EHS = 1
[2][3]
450
-
730
ps
tf
fall time
I/O pins - high-speed
tr
tf
Product data sheet
fall time
tr
rise time
pin configured as output; EHS = 0
[2][3]
1.0
-
1.9
ns
tf
fall time
pin configured as output; EHS = 0
[2][3]
1.0
-
2.0
ns
pin configured as input
[4]
0.3
-
1.3
ns
pin configured as input
[4]
0.2
-
1.2
ns
tr
LPC436X
rise time
rise time
tf
fall time
[1]
Simulated data.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
111 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
[2]
Simulated using 10 cm of 50 Ω PCB trace with 5 pF receiver input. Rise and fall times measured between
80 % and 20 % of the full output signal level.
[3]
The slew rate is configured in the system control block in the SFSP registers using the EHS bit. See the
LPC43xx user manual.
[4]
CL = 20 pF. Rise and fall times measured between 90 % and 10 % of the full input signal level.
[5]
The drive modes are configured in the system control block in the SFSP registers using the EHD bit. See
the LPC43xx user manual.
11.9 I2C-bus
Table 24. Dynamic characteristic: I2C-bus pins
Tamb = 40 C to +105 C; 2.4 V VDD(REG)(3V3) 3.6 V.[1]
Symbol
Parameter
Conditions
Min
Max
Unit
fSCL
SCL clock frequency
Standard-mode
0
100
kHz
Fast-mode
0
400
kHz
Fast-mode Plus
0
1
MHz
of both SDA and
SCL signals
-
300
ns
Fast-mode
20 + 0.1 Cb
300
ns
Fast-mode Plus
-
120
ns
4.7
-
s
[3][4][5][6]
fall time
tf
Standard-mode
tLOW
tHIGH
tHD;DAT
tSU;DAT
[1]
LOW period of the SCL clock
Standard-mode
HIGH period of the SCL clock
[2][3][7]
data hold time
[8][9]
data set-up time
Fast-mode
1.3
-
s
Fast-mode Plus
0.5
-
s
Standard-mode
4.0
-
s
Fast-mode
0.6
-
s
Fast-mode Plus
0.26
-
s
Standard-mode
0
-
s
Fast-mode
0
-
s
Fast-mode Plus
0
-
s
Standard-mode
250
-
ns
Fast-mode
100
-
ns
Fast-mode Plus
50
-
ns
Parameters are valid over operating temperature range unless otherwise specified. See the I2C-bus specification UM10204 for details.
[2]
tHD;DAT is the data hold time that is measured from the falling edge of SCL; applies to data in transmission and the acknowledge.
[3]
A device must internally provide a hold time of at least 300 ns for the SDA signal (with respect to the VIH(min) of the SCL signal) to
bridge the undefined region of the falling edge of SCL.
[4]
Cb = total capacitance of one bus line in pF. If mixed with Hs-mode devices, faster fall times are allowed.
[5]
The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA output stage tf is specified at
250 ns. This allows series protection resistors to be connected in between the SDA and the SCL pins and the SDA/SCL bus lines
without exceeding the maximum specified tf.
[6]
In Fast-mode Plus, fall time is specified the same for both output stage and bus timing. If series resistors are used, designers should
allow for this when considering bus timing.
[7]
The maximum tHD;DAT could be 3.45 s and 0.9 s for Standard-mode and Fast-mode but must be less than the maximum of tVD;DAT or
tVD;ACK by a transition time. This maximum must only be met if the device does not stretch the LOW period (tLOW) of the SCL signal. If
the clock stretches the SCL, the data must be valid by the set-up time before it releases the clock.
[8]
tSU;DAT is the data set-up time that is measured with respect to the rising edge of SCL; applies to data in transmission and the
acknowledge.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
112 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
[9]
A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system but the requirement tSU;DAT = 250 ns must then be met.
This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the
LOW period of the SCL signal, it must output the next data bit to the SDA line tr(max) + tSU;DAT = 1000 + 250 = 1250 ns (according to the
Standard-mode I2C-bus specification) before the SCL line is released. Also the acknowledge timing must meet this set-up time.
tf
SDA
tSU;DAT
70 %
30 %
70 %
30 %
tHD;DAT
tf
70 %
30 %
SCL
tVD;DAT
tHIGH
70 %
30 %
70 %
30 %
70 %
30 %
tLOW
1 / fSCL
S
002aaf425
Fig 26. I2C-bus pins clock timing
11.10 I2S-bus interface
Table 25. Dynamic characteristics: I2S-bus interface pins
Tamb = 40 C to 105 C; 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V; CL = 20 pF.
Conditions and data refer to I2S0 and I2S1 pins. Simulated values.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
common to input and output
tr
rise time
-
4
-
ns
tf
fall time
-
4
-
ns
tWH
pulse width HIGH
on pins I2Sx_TX_SCK
and I2Sx_RX_SCK
36
-
-
ns
tWL
pulse width LOW
on pins I2Sx_TX_SCK
and I2Sx_RX_SCK
36
-
-
ns
-
4.4
-
ns
-
4.3
-
ns
0
-
output
data output valid time on pin I2Sx_TX_SDA
tv(Q)
[1]
on pin I2Sx_TX_WS
input
tsu(D)
data input set-up time on pin I2Sx_RX_SDA
[1]
-
on pin I2Sx_RX_WS
th(D)
data input hold time
on pin I2Sx_RX_SDA
on pin I2Sx_RX_WS
[1]
LPC436X
Product data sheet
0.20
[1]
ns
ns
-
3.7
-
ns
-
3.9
-
ns
Clock to the I2S-bus interface BASE_APB1_CLK = 150 MHz; peripheral clock to the I2S-bus interface
PCLK = BASE_APB1_CLK / 12. I2S clock cycle time Tcy(clk) = 79.2 ns, corresponds to the SCK signal in the
I2S-bus specification.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
113 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Tcy(clk)
tf
tr
I2Sx_TX_SCK
tWH
tWL
I2Sx_TX_SDA
tv(Q)
I2Sx_TX_WS
002aag497
tv(Q)
Fig 27. I2S-bus timing (transmit)
Tcy(clk)
tf
tr
I2Sx_RX_SCK
tWH
tWL
I2Sx_RX_SDA
tsu(D)
th(D)
I2Sx_RX_WS
tsu(D)
002aag498
th(D)
Fig 28. I2S-bus timing (receive)
11.11 USART interface
Table 26. USART dynamic characteristics
Tamb = 40 C to 105 C; 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V; CL = 20 pF. EHS = 1
for all pins. Simulated values.
Symbol
Parameter
Min
Max
Unit
USART master (in synchronous mode)
tsu(D)
data input set-up time
26.6
-
ns
th(D)
data input hold time
0
-
ns
tv(Q)
data output valid time
0
10.4
ns
USART slave (in synchronous mode)
LPC436X
Product data sheet
tsu(D)
data input set-up time
2.4
-
ns
th(D)
data input hold time
0
-
ns
tv(Q)
data output valid time
4.3
24.3
ns
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
114 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Tcy(clk)
SCLK (FES = 1)
SCLK (FES = 0)
tv(Q)
tv(Q)
START
TXD
BIT0
th(D)
tsu(D)
START
RXD
BIT1
BIT0
BIT1
aaa-016717
Fig 29. USART timing
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
115 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11.12 SSP interface
Table 27. Dynamic characteristics: SSP pins in SPI mode
Tamb = 40 C to +105 C; 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V; CL = 20 pF; sampled at 10 % and 90 % of
the signal level; EHS = 1 for all pins. Simulated values.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
1/(25.5 106)
-
-
s
when only transmitting
1/(51
-
-
s
in SPI mode
12.2
-
-
ns
SSP master
Tcy(clk)
clock cycle time
[1]
full-duplex mode
106)
tDS
data set-up time
tDH
data hold time
in SPI mode
3.6
-
-
ns
tv(Q)
data output valid
time
in SPI mode
-
-
6.7
ns
th(Q)
data output hold
time
in SPI mode
1.7
-
-
ns
tlead
lead time
continuous transfer mode
Tcy(clk) + 3.3
-
Tcy(clk) + 8.2
ns
SPI mode; CPOL = 0;
CPHA = 0
tlag
lag time
SPI mode; CPOL = 0;
CPHA = 1
0.5 Tcy(clk) + 3.3 -
0.5 Tcy(clk) + 8.2
ns
SPI mode; CPOL = 1;
CPHA = 0
Tcy(clk) + 3.3
Tcy(clk) + 8.2
ns
SPI mode; CPOL = 1;
CPHA = 1
0.5 Tcy(clk) + 3.3 -
0.5 Tcy(clk) + 8.2
ns
synchronous serial
frame mode
0.5 Tcy(clk) + 3.3 -
0.5 Tcy(clk) + 8.2
ns
microwire frame format
Tcy(clk) + 3.3
-
Tcy(clk) + 8.2
ns
continuous transfer mode
0.5 Tcy(clk)
-
-
ns
SPI mode; CPOL = 0;
CPHA = 1
Tcy(clk)
-
-
ns
SPI mode; CPOL = 1;
CPHA = 0
0.5 Tcy(clk)
-
-
ns
SPI mode; CPOL = 1;
CPHA = 1
Tcy(clk)
-
-
ns
synchronous serial
frame mode
Tcy(clk)
-
-
ns
microwire frame format
0.5 Tcy(clk)
-
-
ns
-
SPI mode; CPOL = 0;
CPHA = 0
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
116 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 27. Dynamic characteristics: SSP pins in SPI mode
Tamb = 40 C to +105 C; 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V; CL = 20 pF; sampled at 10 % and 90 % of
the signal level; EHS = 1 for all pins. Simulated values.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
td
delay time
continuous transfer mode
-
0.5 Tcy(clk)
-
ns
SPI mode; CPOL = 0;
CPHA = 1
-
n/a
-
ns
SPI mode; CPOL = 1;
CPHA = 0
-
0.5 Tcy(clk)
-
ns
SPI mode; CPOL = 1;
CPHA = 1
-
n/a
-
ns
synchronous serial
frame mode
-
Tcy(clk)
-
ns
microwire frame format
-
n/a
-
ns
-
-
204
MHz
1/(11 106)
-
-
s
SPI mode; CPOL = 0;
CPHA = 0
SSP slave
PCLK
Peripheral clock
frequency
Tcy(clk)
clock cycle time
tDS
data set-up time
in SPI mode
1.5
-
-
ns
tDH
data hold time
in SPI mode
2
-
-
ns
tv(Q)
data output valid
time
in SPI mode
-
-
[4 (1/PCLK)] + 1 ns
th(Q)
data output hold
time
in SPI mode
4.5
-
-
ns
tlead
lead time
continuous transfer mode
Tcy(clk)
-
-
ns
SPI mode; CPOL = 0;
CPHA = 1
0.5 Tcy(clk)
-
-
ns
SPI mode; CPOL = 1;
CPHA = 0
Tcy(clk)
-
-
ns
SPI mode; CPOL = 1;
CPHA = 1
0.5 Tcy(clk)
-
-
ns
synchronous serial
frame mode
0.5 Tcy(clk)
-
-
ns
microwire frame format
Tcy(clk)
-
-
ns
[2]
SPI mode; CPOL = 0;
CPHA = 0
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
117 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 27. Dynamic characteristics: SSP pins in SPI mode
Tamb = 40 C to +105 C; 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V; CL = 20 pF; sampled at 10 % and 90 % of
the signal level; EHS = 1 for all pins. Simulated values.
Symbol
Parameter
Conditions
Min
tlag
lag time
continuous transfer mode
Typ
Max
Unit
0.5 x Tcy(clk) + 1.5 -
-
ns
SPI mode; CPOL = 0;
CPHA = 1
Tcy(clk) + 1.5
-
-
ns
SPI mode; CPOL = 1;
CPHA = 0
0.5 Tcy(clk) + 1.5 -
-
ns
SPI mode; CPOL = 1;
CPHA = 1
Tcy(clk) + 1.5
-
-
ns
synchronous serial
frame mode
Tcy(clk) + 1.5
-
-
ns
microwire frame format
0.5 Tcy(clk)
-
-
ns
-
0.5 Tcy(clk)
-
ns
SPI mode; CPOL = 0;
CPHA = 1
-
n/a
-
ns
SPI mode; CPOL = 1;
CPHA = 0
-
0.5 Tcy(clk)
-
ns
SPI mode; CPOL = 1;
CPHA = 1
-
n/a
-
ns
synchronous serial
frame mode
-
Tcy(clk)
-
ns
microwire frame format
-
n/a
-
ns
SPI mode; CPOL = 0;
CPHA = 0
delay time
td
continuous transfer mode
SPI mode; CPOL = 0;
CPHA = 0
[1]
Tcy(clk) = (SSPCLKDIV (1 + SCR) CPSDVSR) / fmain. The clock cycle time derived from the SPI bit rate Tcy(clk) is a function of the
main clock frequency fmain, the SSP peripheral clock divider (SSPCLKDIV), the SSP SCR parameter (specified in the SSP0CR0
register), and the SSP CPSDVSR parameter (specified in the SSP clock prescale register).
[2]
Tcy(clk) 12 Tcy(PCLK).
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
118 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11.13 SPI interface
Table 28. Dynamic characteristics: SPI
Tamb = 40 C to +105 C; 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V. Simulated values.
Symbol
Parameter
Tcy(PCLK)
PCLK cycle time
Tcy(clk)
clock cycle time
Conditions
Min
Typ
Max
5
[1]
Unit
ns
40
-
-
ns
Master
tDS
data set-up time
7.2
-
-
ns
tDH
data hold time
0
-
-
ns
tv(Q)
data output valid time
-
-
3.7
ns
th(Q)
data output hold time
-
-
1.2
ns
tDS
data set-up time
1.2
-
-
ns
tDH
data hold time
3 x Tcy(PCLK) + 0.54
-
-
ns
tv(Q)
data output valid time
-
-
3 x Tcy(PCLK) + 9.7 ns
th(Q)
data output hold time
-
-
2 x Tcy(PCLK) + 7.1 ns
Slave
[1]
Tcy(clk) = 8/BASE_SPI_CLK. Tcy(PCLK) = 1/BASE_SPI_CLK.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
119 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11.14 SSP/SPI timing diagrams
Tcy(clk)
SCK (CPOL = 0)
SCK (CPOL = 1)
SSEL
MOSI (CPHA = 0)
tv(Q)
th(Q)
DATA VALID (MSB)
DATA VALID
DATA VALID (MSB)
DATA VALID (LSB)
DATA VALID (MSB)
IDLE
tDH
tDS
MISO (CPHA = 0)
MOSI (CPHA = 1)
td
tlag
tlead
DATA VALID
DATA VALID (MSB)
DATA VALID (LSB)
tv(Q)
th(Q)
DATA VALID (LSB)
DATA VALID
tDS
MISO (CPHA = 1)
DATA VALID (LSB)
DATA VALID (MSB)
IDLE
DATA VALID (MSB)
tDH
DATA VALID
DATA VALID (MSB)
DATA VALID (MSB)
aaa-013462
Fig 30. SSP in SPI mode and SPI master timing
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
120 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Tcy(clk)
SCK (CPOL = 0)
SCK (CPOL = 1)
SSEL
MISO (CPHA = 0)
tv(Q)
DATA VALID (MSB)
th(Q)
DATA VALID
DATA VALID (MSB)
DATA VALID (LSB)
IDLE
DATA VALID (MSB)
DATA VALID (LSB)
IDLE
DATA VALID (MSB)
tDH
tDS
MOSI (CPHA = 0)
MISO (CPHA = 1)
td
tlag
tlead
DATA VALID
tv(Q)
th(Q)
DATA VALID (LSB)
DATA VALID
tDS
MOSI (CPHA = 1)
DATA VALID (LSB)
DATA VALID (MSB)
IDLE
DATA VALID (MSB)
DATA VALID (MSB)
IDLE
DATA VALID (MSB)
tDH
DATA VALID
aaa-014942
Fig 31. SSP in SPI mode and SPI slave timing
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
121 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11.15 SPIFI
Table 29. Dynamic characteristics: SPIFI
Tamb = 40 C to 105 C; 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V. CL = 20 pF. Sampled
at 90 % and 10 % of the signal level. EHS = 1 for all pins. Simulated values.
Symbol
Parameter
Min
Max
Unit
Tcy(clk)
clock cycle time
9.6
-
ns
tDS
data set-up time
3.2
-
ns
tDH
data hold time
0
-
ns
tv(Q)
data output valid time
-
3.2
ns
th(Q)
data output hold time
0.6
-
ns
Tcy(clk)
SPIFI_SCK
tv(Q)
DATA VALID
SPIFI data out
th(Q)
DATA VALID
tDS
DATA VALID
SPIFI data in
tDH
DATA VALID
002aah409
Fig 32. SPIFI timing (Mode 0)
11.16 SGPIO timing
The following considerations apply to SGPIO timing:
• SGPIO input signals are synchronized by the internal clock SGPIO_CLOCK. To
guarantee that no samples are missed, all input signals should have a duration of at
least one SGPIO_CLOCK cycle plus the set-up and hold times.
• When an external clock input is used to generate output data, synchronization causes
a latency of at least one SGPIO_CLOCK cycle. The maximum output data rate is one
output every two SGPIO_CLOCK cycles.
• Synchronization also causes a latency of one SGPIO_CLOCK cycle when sampling
several inputs. This may cause inputs with very similar timings to be sampled with a
difference of one SGPIO_CLOCK cycle.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
122 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 30. Dynamic characteristics: SGPIO
Tamb = 40 C to +85 C; 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V. Simulated values.
Symbol
Parameter
Min
Typ
Max
Unit
tsu(D)
data input set-up time
th(D)
data input hold time
[1]
2
-
-
ns
TSGPIO + 2
-
-
ns
data input set-up time sampled by
SGPIO_CLOCK
[1]
tsu(D)
TSGPIO + 2
-
-
ns
th(D)
data input hold time
[1]
TSGPIO + 2
-
-
ns
tv(Q)
data output valid time
[1]
-
-
2 x TSGPIO
ns
data output hold time
[1]
TSGPIO
-
tv(Q)
data output valid time
sampled by
SGPIO_CLOCK
[1]
-3
-
3
ns
th(Q)
data output hold time
sampled by
SGPIO_CLOCK
[1]
-3
-
3
ns
th(Q)
[1]
Conditions
sampled by
SGPIO_CLOCK
ns
SGPIO_CLOCK is the internally generated SGPIO clock. TSGPIO = 1/fSGPIO_CLOCK.
SGPIO_CLOCK
CLKINext
sync(CLKINext) = CLKINi
th(D)
tsu(D)
DIN
DINi
sync(DIN)
DINi
tv(Q)
CLKout
th(Q)
Dout
DQi
002aah668
Fig 33. SGPIO timing
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
123 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11.17 External memory interface
Table 31. Dynamic characteristics: Static asynchronous external memory interface
CL = 22 pF for EMC_Dn CL = 20 pF for all others; Tamb = 40 C to 105 C; 2.4 V VDD(REG)(3V3) 3.6 V;
2.7 V VDD(IO) 3.6 V; values guaranteed by design; the values in the table have been calculated with WAITTURN = 0x0 in
STATICWAITTURN register. Timing parameters are given for single memory access cycles. In a normal read operation, the
EMC changes the address while CS is asserted which results in multiple memory accesses.
Symbol
Parameter[1]
Conditions
Min
Typ
Max
Unit
3.1
-
1.6
ns
0.6 + Tcy(clk)
WAITOEN
-
1.3 + Tcy(clk)
WAITOEN
ns
0.7
-
1.8
ns
Read cycle parameters
tCSLAV
CS LOW to address valid
time
tCSLOEL
CS LOW to OE LOW time
tCSLBLSL
CS LOW to BLS LOW time PB = 1
[2][2]
[2]
0.6 +
(WAITRD
WAITOEN + 1)
Tcy(clk)
0.4 +
ns
(WAITRD
WAITOEN + 1)
Tcy(clk)
-
-
16 +
ns
(WAITRD
WAITOEN +1)
Tcy(clk)
tOELOEH
OE LOW to OE HIGH time
tam
memory access time
th(D)
data input hold time
tCSHBLSH
CS HIGH to BLS HIGH
time
tCSHOEH
CS HIGH to OE HIGH time
tOEHANV
OE HIGH to address invalid PB = 1
2.0
-
2.6
ns
tCSHEOR
CS HIGH to end of read
time
[3]
2.0
-
0
ns
tCSLSOR
CS LOW to start of read
time
[4]
0
-
1.8
ns
3.1
-
1.6
ns
3.1
-
1.5
ns
PB = 1
16
-
-
ns
0.4
-
1.9
ns
0.4
-
1.4
ns
Write cycle parameters
tCSLAV
CS LOW to address valid
time
tCSLDV
CS LOW to data valid time
tCSLWEL
CS LOW to WE LOW time
tCSLBLSL
CS LOW to BLS LOW time PB = 1
tWELWEH
WE LOW to WE HIGH time PB = 1
[2]
tWEHDNV
WE HIGH to data invalid
time
PB = 1
tWEHEOW
WE HIGH to end of write
time
PB = 1
tCSLBLSL
CS LOW to BLS LOW
PB = 0
LPC436X
Product data sheet
1.5 +
(WAITWEN + 1)
Tcy(clk)
0.2 +
ns
(WAITWEN + 1)
Tcy(clk)
0.7
-
1.8
ns
0.6 +
(WAITWR
WAITWEN + 1)
Tcy(clk)
-
0.4 +
(WAITWR
WAITWEN + 1)
Tcy(clk)
ns
[2]
0.9 + Tcy(clk)
-
2.3 + Tcy(clk)
ns
[2][5]
0.4 + Tcy(clk)
-
0.3 + Tcy(clk)
ns
PB = 1
0.7 +
(WAITWEN + 1)
Tcy(clk)
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
1.8 +
ns
(WAITWEN + 1)
Tcy(clk)
© NXP Semiconductors N.V. 2016. All rights reserved.
124 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 31. Dynamic characteristics: Static asynchronous external memory interface …continued
CL = 22 pF for EMC_Dn CL = 20 pF for all others; Tamb = 40 C to 105 C; 2.4 V VDD(REG)(3V3) 3.6 V;
2.7 V VDD(IO) 3.6 V; values guaranteed by design; the values in the table have been calculated with WAITTURN = 0x0 in
STATICWAITTURN register. Timing parameters are given for single memory access cycles. In a normal read operation, the
EMC changes the address while CS is asserted which results in multiple memory accesses.
Symbol
Parameter[1]
Conditions
tBLSLBLSH
BLS LOW to BLS HIGH
time
PB = 0
tBLSHEOW
BLS HIGH to end of write
time
PB = 0
tBLSHDNV
BLS HIGH to data invalid
time
PB = 0
tCSHEOW
CS HIGH to end of write
time
tBLSHDNV
BLS HIGH to data invalid
time
tWEHANV
WE HIGH to address
invalid time
Min
Typ
Max
Unit
0.9 +
(WAITWR
WAITWEN + 1)
Tcy(clk)
-
0.1 +
(WAITWR
WAITWEN + 1)
Tcy(clk)
ns
[2][5]
1.9 + Tcy(clk)
-
0.5 + Tcy(clk)
ns
[2]
2.5 + Tcy(clk)
-
1.4 + Tcy(clk)
ns
2.0
-
0
ns
PB = 1
2.5
-
1.4
ns
PB = 1
0.9 + Tcy(clk)
-
2.4 + Tcy(clk)
ns
[2]
[5]
[1]
Parameters specified for 40 % of VDD(IO) for rising edges and 60 % of VDD(IO) for falling edges.
[2]
Tcy(clk) = 1/CCLK (see LPC43xx/LPC43Sxx User manual).
[3]
End Of Read (EOR): longest of tCSHOEH, tOEHANV, tCSHBLSH.
[4]
Start Of Read (SOR): longest of tCSLAV, tCSLOEL, tCSLBLSL.
[5]
End Of Write (EOW): earliest of address not valid or EMC_BLSn HIGH.
EMC_An
tCSLAV
tCSLAV
tOEHANV
tCSHEOW
EMC_CSn
tCSLOEL
tOELOEH
EMC_OE
tCSHOEH
tBLSHEOW
tCSLBLSL tBLSLBLSH
EMC_BLSn
EMC_WE
tCSLDV
tam
tCSHEOR
tCSLSOR
tBLSHDNV
th(D)
EMC_Dn
SOR
EOR
EOW
002aag699
Fig 34. External static memory read/write access (PB = 0)
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
125 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
EMC_An
tCSLAV
tCSLAV
tOEHANV
tCSHEOW
EMC_CSn
tCSLOEL
tOELOEH
EMC_OE
tCSLBLSL
tCSHOEH
tCSLBLSL
EMC_BLSn
tCSHBLSH
tCSLWEL tWELWEH
tWEHEOW
EMC_WE
tBLSHDNV
tam
tCSHEOR
th(D)
tCSLSOR
tCSLDV
tWEHDNV
EMC_Dn
SOR
EOR
EOW
002aag700
Fig 35. External static memory read/write access (PB = 1)
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
126 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 32. Dynamic characteristics: Dynamic external memory interface
Simulated data over temperature and process range; CL = 10 pF for EMC_DYCSn, EMC_RAS, EMC_CAS, EMC_WE,
EMC_An; CL = 9 pF for EMC_Dn; CL = 5 pF for EMC_DQMOUTn, EMC_CLKn, EMC_CKEOUTn; Tamb = 40 C to 105 C;
2.4 V VDD(REG)(3V3) 3.6 V; VDD(IO) =3.3 V 10 %; RD = 1 (see LPC43xx/LPC43Sxx User manual); EMC_CLKn delays
CLK0_DELAY = CLK1_DELAY = CLK2_DELAY = CLK3_DELAY = 0.
Symbol
Parameter
Min
Typ
Max
Unit
Tcy(clk)
clock cycle time
8.4
-
-
ns
3.1 + 0.5 Tcy(clk)
5.1 + 0.5 Tcy(clk)
ns
-
ns
4.9 + 0.5 Tcy(clk)
ns
Common to read and write cycles
td(DYCSV)
dynamic chip select valid delay time
-
th(DYCS)
dynamic chip select hold time
0.3 + 0.5 Tcy(clk) 0.9 + 0.5 Tcy(clk)
td(RASV)
row address strobe valid delay time
-
th(RAS)
row address strobe hold time
0.5 + 0.5 Tcy(clk) 1.1 + 0.5 Tcy(clk)
td(CASV)
column address strobe valid delay time
-
th(CAS)
column address strobe hold time
0.3 + 0.5 Tcy(clk) 0.9 + 0.5 Tcy(clk)
td(WEV)
write enable valid delay time
-
th(WE)
write enable hold time
1.3 + 0.5 Tcy(clk) 1.4 + 0.5 Tcy(clk)
td(DQMOUTV)
DQMOUT valid delay time
-
th(DQMOUT)
DQMOUT hold time
0.2 + 0.5 Tcy(clk) 0.8 + 0.5 Tcy(clk)
td(AV)
address valid delay time
-
th(A)
address hold time
0.3 + 0.5 Tcy(clk) 0.9 + 0.5 Tcy(clk)
-
ns
td(CKEOUTV)
CKEOUT valid delay time
-
3.1 + 0.5 Tcy(clk)
5.1 + 0.5 Tcy(clk)
ns
th(CKEOUT)
CKEOUT hold time
0.5 Tcy(clk)
0.7 + 0.5 Tcy(clk)
-
ns
3.1 + 0.5 Tcy(clk)
2.9 + 0.5 Tcy(clk)
3.2 + 0.5 Tcy(clk)
3.1 + 0.5 Tcy(clk)
3.8 + 0.5 Tcy(clk)
-
ns
4.6 + 0.5 Tcy(clk)
ns
-
ns
5.9 + 0.5 Tcy(clk)
ns
-
ns
5.0 + 0.5 Tcy(clk)
ns
-
ns
6.3 + 0.5 Tcy(clk)
ns
Read cycle parameters
tsu(D)
data input set-up time
1.5
0.5
-
ns
th(D)
data input hold time
2.2
0.8
-
ns
Write cycle parameters
td(QV)
data output valid delay time
-
3.8 + 0.5 Tcy(clk)
6.2 + 0.5 Tcy(clk)
ns
th(Q)
data output hold time
0.5 Tcy(clk)
0.7 + 0.5 Tcy(clk)
-
ns
Table 33.
Dynamic characteristics: Dynamic external memory interface; EMC_CLK[3:0]
delay values
Tamb = 40 C to 105 C; VDD(IO) =3.3 V 10 %; 2.4 V VDD(REG)(3V3) 3.6 V.
Symbol
Parameter
Conditions
td
delay time
delay value
CLKn_DELAY = 0
[1]
LPC436X
Product data sheet
Min
Typ
Max
Unit
[1]
0.0
0.0
0.0
ns
CLKn_DELAY = 1
[1]
0.4
0.5
0.8
ns
CLKn_DELAY = 2
[1]
0.7
1.0
1.7
ns
CLKn_DELAY = 3
[1]
1.1
1.6
2.5
ns
CLKn_DELAY = 4
[1]
1.4
2.0
3.3
ns
CLKn_DELAY = 5
[1]
1.7
2.6
4.1
ns
CLKn_DELAY = 6
[1]
2.1
3.1
4.9
ns
CLKn_DELAY = 7
[1]
2.5
3.6
5.8
ns
Program the EMC_CLKn delay values in the EMCDELAYCLK register (see the LPC43xx User manual).
The delay values must be the same for all SDRAM clocks EMC_CLKn: CLK0_DELAY = CLK1_DELAY =
CLK2_DELAY = CLK3_DELAY.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
127 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
EMC_CLKn
delay > 0
EMC_CLKn delay td; programmable CLKn_DELAY
Tcy(clk)
EMC_CLKn
delay = 0
td(xV) - td
EMC_DYCSn,
EMC_RAS,
EMC_CAS,
EMC_WE,
EMC_CKEOUTn,
EMC_A[22:0],
EMC_DQMOUTn
td(xV)
th(x) - td
th(x)
td(QV) - td
td(QV)
th(Q) - td
th(Q)
EMC_D[31:0]
write
tsu(D)
th(D)
EMC_D[31:0]
read; delay > 0
tsu(D)
th(D)
EMC_D[31:0]
read; delay = 0
002aag703
For the programmable EMC_CLK[3:0] clock delays CLKn_DELAY, see Figure 32.
Remark: For SDRAM operation, set CLK0_DELAY = CLK1_DELAY = CLK2_DELAY = CLK3_DELAY in the EMCDELAYCLK
register.
Fig 36. SDRAM timing
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
128 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11.18 USB interface
Table 34. Dynamic characteristics: USB0 and USB1 pins (full-speed)
CL = 50 pF; Rpu = 1.5 k on D+ to VDD(IO), unless otherwise specified; 3.0 V VDD(IO) 3.6 V.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tr
rise time
10 % to 90 %
4.0
-
20.0
ns
tf
fall time
10 % to 90 %
4.0
-
20.0
ns
tFRFM
differential rise and fall time matching
tr / tf
90
-
111.11
%
VCRS
output signal crossover voltage
1.3
-
2.0
V
tFEOPT
source SE0 interval of EOP
see Figure 37
160
-
175
ns
tFDEOP
source jitter for differential transition
to SE0 transition
see Figure 37
2
-
+5
ns
tJR1
receiver jitter to next transition
18.5
-
+18.5
ns
tJR2
receiver jitter for paired transitions
10 % to 90 %
9
-
+9
ns
tEOPR1
EOP width at receiver
must reject as
EOP; see
Figure 37
[1]
40
-
-
ns
tEOPR2
EOP width at receiver
must accept as
EOP; see
Figure 37
[1]
82
-
-
ns
[1]
Characterized but not implemented as production test. Guaranteed by design.
Remark: If only USB0 (HS USB) is used, the pins VDDREG and VDDIO can be at
different voltages within the operating range but should have the same ramp up time. If
USB1(FS USB) is used, the pins VDDREG and VDDIO should be a minimum of 3.0 V and
be tied together.
TPERIOD
crossover point
extended
crossover point
differential
data lines
source EOP width: tFEOPT
differential data to
SE0/EOP skew
n × TPERIOD + tFDEOP
receiver EOP width: tEOPR1, tEOPR2
002aab561
Fig 37. Differential data-to-EOP transition skew and EOP width
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
129 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 35.
Symbol
Static characteristics: USB0 PHY pins[1]
Parameter
Conditions
Min
Typ
Max
Unit
-
68
-
mW
-
18
-
mA
High-speed mode
Pcons
[2]
power consumption
IDDA(3V3) analog supply current (3.3 V)
on pin USB0_VDDA3V3_DRIVER;
[3]
total supply current
IDDD
during transmit
-
31
-
mA
during receive
-
14
-
mA
with driver tri-stated
-
14
-
mA
-
7
-
mA
-
15
-
mW
digital supply current
Full-speed/low-speed mode
Pcons
IDDA(3V3) analog supply current (3.3 V)
IDDD
[2]
power consumption
on pin USB0_VDDA3V3_DRIVER;
total supply current
-
3.5
-
mA
during transmit
-
5
-
mA
during receive
-
3
-
mA
with driver tri-stated
-
3
-
mA
-
3
-
mA
-
24
-
A
with driver tri-stated
-
24
-
A
with OTG functionality enabled
-
3
-
mA
-
30
-
A
4.4
-
-
V
digital supply current
Suspend mode
IDDA(3V3) analog supply current (3.3 V)
IDDD
digital supply current
VBUS detector outputs
threshold voltage
Vth
Vhys
[1]
hysteresis voltage
for VBUS valid
for session end
0.2
-
0.8
V
for A valid
0.8
-
2
V
for B valid
2
-
4
V
for session end
-
150
10
mV
A valid
-
200
10
mV
B valid
-
200
10
mV
Characterized but not implemented as production test.
[2]
Total average power consumption.
[3]
The driver is active only 20 % of the time.
11.19 Ethernet
Remark: The timing characteristics of the ENET_MDC and ENET_MDIO signals comply
with the IEEE standard 802.3.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
130 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 36. Dynamic characteristics: Ethernet
Tamb = 40 C to 105 C, 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V. Values guaranteed
by design.
Symbol Parameter
Conditions
Min
Max
Unit
[1]
-
50
MHz
clock duty cycle
[1]
50
50
%
tsu
set-up time
for ENET_TXDn, ENET_TX_EN,
ENET_RXDn, ENET_RX_ER,
ENET_RX_DV
[1][2]
4
-
ns
th
hold time
for ENET_TXDn, ENET_TX_EN,
ENET_RXDn, ENET_RX_ER,
ENET_RX_DV
[1][2]
2
-
ns
clock frequency
for ENET_TX_CLK
[1]
-
25
MHz
[1]
RMII mode
clock frequency
fclk
clk
for ENET_RX_CLK
MII mode
fclk
clk
clock duty cycle
50
50
%
tsu
set-up time
for ENET_TXDn, ENET_TX_EN,
ENET_TX_ER
[1][2]
4
-
ns
th
hold time
for ENET_TXDn, ENET_TX_EN,
ENET_TX_ER
[1][2]
2
-
ns
fclk
clock frequency
for ENET_RX_CLK
[1]
-
25
MHz
clock duty cycle
[1]
50
50
%
tsu
set-up time
for ENET_RXDn, ENET_RX_ER,
ENET_RX_DV
[1][2]
4
-
ns
th
hold time
for ENET_RXDn, ENET_RX_ER,
ENET_RX_DV
[1][2]
2
-
ns
clk
[1]
Output drivers can drive a load 25 pF accommodating over 12 inch of PCB trace and the input
capacitance of the receiving device.
[2]
Timing values are given from the point at which the clock signal waveform crosses 1.4 V to the valid input or
output level.
ENET_RX_CLK
ENET_TX_CLK
ENET_RXD[n]
ENET_RX_DV
ENET_RX_ER
ENET_TXD[n]
ENET_TX_EN
ENET_TX_ER
tsu
th
002aag210
Fig 38. Ethernet timing
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
131 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
11.20 SD/MMC
Table 37. Dynamic characteristics: SD/MMC
Tamb = 40 C to +105 C, 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V, CL = 20 pF.
SAMPLE_DELAY = 0x9, DRV_DELAY = 0x6 in the SDDELAY register, sampled at 90 % and 10 %
of the signal level, EHS = 1 for SD_CLK pin, EHS = 0 for SD_DATn and SD_CMD pins. Simulated
values.
Symbol Parameter
Conditions
Min
Max
Unit
fclk
clock frequency
on pin SD_CLK; data transfer mode
-
52
MHz
tsu(D)
data input set-up time
on pins SD_DATn as inputs
5.2
-
ns
on pins SD_CMD as inputs
7
-
ns
th(D)
data input hold time
on pins SD_DATn as inputs
0.2
-
ns
on pins SD_CMD as inputs
1
ns
td(QV)
data output valid delay
time
on pins SD_DATn as outputs
-
15.7
ns
on pins SD_CMD as outputs
-
15.9
ns
th(Q)
data output hold time
on pins SD_DATn as outputs
3.5
-
ns
on pins SD_CMD as outputs
3.5
-
ns
Tcy(clk)
SD_CLK
td(QV)
th(Q)
SD_CMD (O)
SD_DATn (O)
tsu(D)
th(D)
SD_CMD (I)
SD_DATn (I)
002aag204
Fig 39. SD/MMC timing
11.21 LCD
Table 38. Dynamic characteristics: LCD
Tamb = 40 C to 105 C; 2.4 V VDD(REG)(3V3) 3.6 V; 2.7 V VDD(IO) 3.6 V; CL = 20 pF.
Simulated values.
Symbol Parameter
LPC436X
Product data sheet
Conditions
Min
Typ
Max
Unit
on pin LCD_DCLK
fclk
clock frequency
-
50
-
MHz
td(QV)
data output valid
delay time
-
-
17
ns
th(Q)
data output hold time
8.5
-
-
ns
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
132 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
12. ADC/DAC electrical characteristics
Table 39. ADC characteristics
VDDA(3V3) over specified ranges; Tamb = 40 C to +105 C; unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ
Max
Unit
VIA
analog input voltage
0
-
VDDA(3V3)
V
Cia
analog input capacitance
-
-
2
pF
ED
differential linearity error
-
0.8
-
LSB
-
1.0
-
LSB
-
0.8
-
LSB
-
1.5
-
LSB
-
0.15
-
LSB
-
0.15
-
LSB
-
0.3
-
%
-
0.35
-
%
-
3
-
LSB
2.4 V VDDA(3V3) < 2.7 V
-
4
-
LSB
see Figure 41
-
-
1/(7 fclk(ADC)
Cia)
k
-
-
1.2
M
-
-
4.5
MHz
-
-
400
kSamples/s
1.5
MSamples/s
2.7 V VDDA(3V3) 3.6 V
[1][2]
2.4 V VDDA(3V3) < 2.7 V
EL(adj)
integral non-linearity
2.7 V VDDA(3V3) 3.6 V
[3]
2.4 V VDDA(3V3) < 2.7 V
offset error
EO
2.7 V VDDA(3V3) 3.6 V
[4]
2.4 V VDDA(3V3) < 2.7 V
gain error
EG
2.7 V VDDA(3V3) 3.6 V
[5]
2.4 V VDDA(3V3) < 2.7 V
absolute error
ET
Rvsi
voltage source interface
resistance
Ri
input resistance
fclk(ADC)
ADC clock frequency
fs
sampling frequency
2.7 V VDDA(3V3) 3.6 V
[6]
[7][8]
10-bit resolution; 11 clock
cycles
2-bit resolution; 3 clock
cycles
[1]
The ADC is monotonic, there are no missing codes.
[2]
The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 40.
[3]
The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
appropriate adjustment of gain and offset errors. See Figure 40.
[4]
The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the
ideal curve. See Figure 40.
[5]
The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset
error, and the straight line which fits the ideal transfer curve. See Figure 40.
[6]
The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated
ADC and the ideal transfer curve. See Figure 40.
[7]
Tamb = 25 C.
[8]
Input resistance Ri depends on the sampling frequency fs: Ri = 2 k + 1 / (fs Cia).
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
133 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
offset
error
EO
gain
error
EG
1023
1022
1021
1020
1019
1018
(2)
7
code
out
(1)
6
5
(5)
4
(4)
3
(3)
2
1 LSB
(ideal)
1
0
1
2
3
4
5
6
7
1018
1019
1020
1021
1022
1023
1024
VIA (LSBideal)
offset error
EO
1 LSB =
VDDA(3V3) − VSSA
1024
002aaf959
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
(3) Differential linearity error (ED).
(4) Integral non-linearity (EL(adj)).
(5) Center of a step of the actual transfer curve.
Fig 40. 10-bit ADC characteristics
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
134 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Rvsi
LPC43xx
2 kΩ (analog pin)
2.2 kΩ (multiplexed pin)
ADC0_n/ADC1_n
Rs
ADC
COMPARATOR
Cia = 2 pF
VEXT
VSS
002aah084
Rs < 1/((7 fclk(ADC) Cia) 2 k
Fig 41. ADC interface to pins
Table 40. DAC characteristics
VDDA(3V3) over specified ranges; Tamb = 40 C to +105 C; unless otherwise specified
Symbol
Parameter
Conditions
ED
differential linearity error
2.7 V VDDA(3V3) 3.6 V
[1]
2.4 V VDDA(3V3) < 2.7 V
EL(adj)
integral non-linearity
code = 0 to 975
[1]
Min
Typ
Max
Unit
-
0.8
-
LSB
-
1.0
-
LSB
-
1.0
-
LSB
2.7 V VDDA(3V3) 3.6 V
2.4 V VDDA(3V3) < 2.7 V
EO
offset error
2.7 V VDDA(3V3) 3.6 V
EG
gain error
2.7 V VDDA(3V3) 3.6 V
-
1.5
-
LSB
[1]
-
0.8
-
LSB
-
1.0
-
LSB
[1]
-
0.3
-
%
-
1.0
-
%
-
-
200
pF
1
-
-
k
2.4 V VDDA(3V3) < 2.7 V
2.4 V VDDA(3V3) < 2.7 V
CL
load capacitance
RL
load resistance
ts
settling time
[1]
[1]
In the DAC CR register, bit BIAS = 0 (see the LPC43xx/LPC43Sxx user manual).
[2]
Settling time is calculated within 1/2 LSB of the final value.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
0.4
© NXP Semiconductors N.V. 2016. All rights reserved.
135 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
13. Application information
13.1 LCD panel signal usage
Table 41.
LCD panel connections for STN single panel mode
External pin
4-bit mono STN single panel
8-bit mono STN single panel
Color STN single panel
LPC43xx pin
used
LCD function
LPC43xx pin
used
LCD function
LPC43xx pin
used
LCD function
LCD_VD[23:8]
-
-
-
-
-
-
LCD_VD7
-
-
P8_4
UD[7]
P8_4
UD[7]
LCD_VD6
-
-
P8_5
UD[6]
P8_5
UD[6]
LCD_VD5
-
-
P8_6
UD[5]
P8_6
UD[5]
LCD_VD4
-
-
P8_7
UD[4]
P8_7
UD[4]
LCD_VD3
P4_2
UD[3]
P4_2
UD[3]
P4_2
UD[3]
LCD_VD2
P4_3
UD[2]
P4_3
UD[2]
P4_3
UD[2]
LCD_VD1
P4_4
UD[1]
P4_4
UD[1]
P4_4
UD[1]
LCD_VD0
P4_1
UD[0]
P4_1
UD[0]
P4_1
UD[0]
LCD_LP
P7_6
LCDLP
P7_6
LCDLP
P7_6
LCDLP
LCD_ENAB/
LCDM
P4_6
LCDENAB/
LCDM
P4_6
LCDENAB/
LCDM
P4_6
LCDENAB/
LCDM
LCD_FP
P4_5
LCDFP
P4_5
LCDFP
P4_5
LCDFP
LCD_DCLK
P4_7
LCDDCLK
P4_7
LCDDCLK
P4_7
LCDDCLK
LCD_LE
P7_0
LCDLE
P7_0
LCDLE
P7_0
LCDLE
LCD_PWR
P7_7
CDPWR
P7_7
LCDPWR
P7_7
LCDPWR
GP_CLKIN
PF_4
LCDCLKIN
PF_4
LCDCLKIN
PF_4
LCDCLKIN
Table 42.
LCD panel connections for STN dual panel mode
External pin
4-bit mono STN dual panel
8-bit mono STN dual panel
Color STN dual panel
LPC43xx pin
used
LCD function
LPC43xx pin
used
LCD function
LPC43xx pin
used
LCD function
LCD_VD[23:16] -
-
-
-
-
-
LCD_VD15
-
-
PB_4
LD[7]
PB_4
LD[7]
LCD_VD14
-
-
PB_5
LD[6]
PB_5
LD[6]
LCD_VD13
-
-
PB_6
LD[5]
PB_6
LD[5]
LCD_VD12
-
-
P8_3
LD[4]
P8_3
LD[4]
LCD_VD11
P4_9
LD[3]
P4_9
LD[3]
P4_9
LD[3]
LCD_VD10
P4_10
LD[2]
P4_10
LD[2]
P4_10
LD[2]
LCD_VD9
P4_8
LD[1]
P4_8
LD[1]
P4_8
LD[1]
LCD_VD8
P7_5
LD[0]
P7_5
LD[0]
P7_5
LD[0]
LCD_VD7
-
-
UD[7]
P8_4
UD[7]
LCD_VD6
-
-
P8_5
UD[6]
P8_5
UD[6]
LCD_VD5
-
-
P8_6
UD[5]
P8_6
UD[5]
LCD_VD4
-
-
P8_7
UD[4]
P8_7
UD[4]
LCD_VD3
P4_2
UD[3]
P4_2
UD[3]
P4_2
UD[3]
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
136 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 42.
LCD panel connections for STN dual panel mode
External pin
4-bit mono STN dual panel
8-bit mono STN dual panel
Color STN dual panel
LPC43xx pin
used
LCD function
LPC43xx pin
used
LCD function
LPC43xx pin
used
LCD function
LCD_VD2
P4_3
UD[2]
P4_3
UD[2]
P4_3
UD[2]
LCD_VD1
P4_4
UD[1]
P4_4
UD[1]
P4_4
UD[1]
LCD_VD0
P4_1
UD[0]
P4_1
UD[0]
P4_1
UD[0]
LCD_LP
P7_6
LCDLP
P7_6
LCDLP
P7_6
LCDLP
LCD_ENAB/
LCDM
P4_6
LCDENAB/
LCDM
P4_6
LCDENAB/
LCDM
P4_6
LCDENAB/
LCDM
LCD_FP
P4_5
LCDFP
P4_5
LCDFP
P4_5
LCDFP
LCD_DCLK
P4_7
LCDDCLK
P4_7
LCDDCLK
P4_7
LCDDCLK
LCD_LE
P7_0
LCDLE
P7_0
LCDLE
P7_0
LCDLE
LCD_PWR
P7_7
LCDPWR
P7_7
LCDPWR
P7_7
LCDPWR
GP_CLKIN
PF_4
LCDCLKIN
PF_4
LCDCLKIN
PF_4
LCDCLKIN
Table 43.
External
pin
LCD panel connections for TFT panels
TFT 12 bit (4:4:4
mode)
TFT 16 bit (5:6:5 mode)
TFT 16 bit (1:5:5:5 mode) TFT 24 bit
LPC43xx
pin used
LCD
function
LPC43xx
pin used
LCD
function
LPC43xx pin LCD
used
function
LPC43xx
pin used
LCD
function
LCD_VD23 PB_0
BLUE3
PB_0
BLUE4
PB_0
BLUE4
PB_0
BLUE7
LCD_VD22 PB_1
BLUE2
PB_1
BLUE3
PB_1
BLUE3
PB_1
BLUE6
LCD_VD21 PB_2
BLUE1
PB_2
BLUE2
PB_2
BLUE2
PB_2
BLUE5
LCD_VD20 PB_3
BLUE0
PB_3
BLUE1
PB_3
BLUE1
PB_3
BLUE4
LCD_VD19 -
-
P7_1
BLUE0
P7_1
BLUE0
P7_1
BLUE3
LCD_VD18 -
-
-
-
P7_2
intensity
P7_2
BLUE2
LCD_VD17 -
-
-
-
-
-
P7_3
BLUE1
LCD_VD16 -
-
-
-
-
-
P7_4
BLUE0
LCD_VD15 PB_4
GREEN3
PB_4
GREEN5
PB_4
GREEN4
PB_4
GREEN7
LCD_VD14 PB_5
GREEN2
PB_5
GREEN4
PB_5
GREEN3
PB_5
GREEN6
LCD_VD13 PB_6
GREEN1
PB_6
GREEN3
PB_6
GREEN2
PB_6
GREEN5
LCD_VD12 P8_3
GREEN0
P8_3
GREEN2
P8_3
GREEN1
P8_3
GREEN4
LCD_VD11
-
P4_9
GREEN1
P4_9
GREEN0
P4_9
GREEN3
-
LCD_VD10 -
-
P4_10
GREEN0
P4_10
intensity
P4_10
GREEN2
LCD_VD9
-
-
-
-
-
-
P4_8
GREEN1
LCD_VD8
-
-
-
-
-
-
P7_5
GREEN0
LCD_VD7
P8_4
RED3
P8_4
RED4
P8_4
RED4
P8_4
RED7
LCD_VD6
P8_5
RED2
P8_5
RED3
P8_5
RED3
P8_5
RED6
LCD_VD5
P8_6
RED1
P8_6
RED2
P8_6
RED2
P8_6
RED5
LCD_VD4
P8_7
RED0
P8_7
RED1
P8_7
RED1
P8_7
RED4
LCD_VD3
-
-
P4_2
RED0
P4_2
RED0
P4_2
RED3
LCD_VD2
-
-
-
-
P4_3
intensity
P4_3
RED2
LCD_VD1
-
-
-
-
-
-
P4_4
RED1
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
137 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 43.
External
pin
LCD panel connections for TFT panels
TFT 12 bit (4:4:4
mode)
TFT 16 bit (5:6:5 mode)
TFT 16 bit (1:5:5:5 mode) TFT 24 bit
LPC43xx
pin used
LPC43xx
pin used
LPC43xx pin LCD
used
function
LCD
function
LCD
function
LPC43xx
pin used
LCD
function
LCD_VD0
-
-
-
-
-
-
P4_1
RED0
LCD_LP
P7_6
LCDLP
P7_6
LCDLP
P7_6
LCDLP
P7_6
LCDLP
LCDENAB/
LCDM
P4_6
LCDENAB/ P4_6
LCDM
LCD_ENAB P4_6
/LCDM
LCDENAB/ P4_6
LCDM
LCD_FP
P4_5
LCDENAB/
LCDM
LCDFP
P4_5
LCDFP
P4_5
LCDFP
P4_5
LCDFP
LCD_DCLK P4_7
LCDDCLK
P4_7
LCDDCLK
P4_7
LCDDCLK
P4_7
LCDDCLK
LCD_LE
P7_0
LCDLE
P7_0
LCDLE
P7_0
LCDLE
P7_0
LCDLE
LCD_PWR
P7_7
LCDPWR
P7_7
LCDPWR
P7_7
LCDPWR
P7_7
LCDPWR
GP_CLKIN
PF_4
LCDCLKIN PF_4
LCDCLKIN
PF_4
LCDCLKIN PF_4
LCDCLKIN
13.2 Crystal oscillator
The crystal oscillator is controlled by the XTAL_OSC_CTRL register in the CGU (see
LPC43xx/LPC43Sxx user manual).
The crystal oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can be
boosted to a higher frequency, up to the maximum CPU operating frequency, by the PLL.
The oscillator can operate in one of two modes: slave mode and oscillation mode.
• In slave mode, couple the input clock signal with a capacitor of 100 pF (CC in
Figure 42), with an amplitude of at least 200 mV (RMS). The XTAL2 pin in this
configuration can be left unconnected.
• External components and models used in oscillation mode are shown in Figure 43,
and in Table 44 and Table 45. Since the feedback resistance is integrated on chip,
only a crystal and the capacitances CX1 and CX2 need to be connected externally in
case of fundamental mode oscillation (L, CL and RS represent the fundamental
frequency). Capacitance CP in Figure 43 represents the parallel package capacitance
and must not be larger than 7 pF. Parameters FC, CL, RS and CP are supplied by the
crystal manufacturer.
Table 44.
Fundamental oscillation
frequency
Maximum crystal series
resistance RS
External load capacitors
CX1, CX2
2 MHz
< 200
33 pF, 33 pF
< 200
39 pF, 39 pF
< 200
56 pF, 56 pF
< 200
18 pF, 18 pF
< 200
39 pF, 39 pF
4 MHz
8 MHz
LPC436X
Product data sheet
Recommended values for CX1/X2 in oscillation mode (crystal and external
components parameters) low frequency mode
< 200
56 pF, 56 pF
< 200
18 pF, 18 pF
< 200
39 pF, 39 pF
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
138 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Table 44.
Recommended values for CX1/X2 in oscillation mode (crystal and external
components parameters) low frequency mode
Fundamental oscillation
frequency
Maximum crystal series
resistance RS
External load capacitors
CX1, CX2
12 MHz
< 160
18 pF, 18 pF
< 160
39 pF, 39 pF
16 MHz
< 120
18 pF, 18 pF
< 80
33 pF, 33 pF
< 100
18 pF, 18 pF
< 80
33 pF, 33 pF
20 MHz
Table 45.
Recommended values for CX1/X2 in oscillation mode (crystal and external
components parameters) high frequency mode
Fundamental oscillation
frequency
Maximum crystal series
resistance RS
External load capacitors CX1,
CX2
15 MHz
< 80
18 pF, 18 pF
20 MHz
< 80
39 pF, 39 pF
< 100
47 pF, 47 pF
LPC43xx
XTAL1
Ci
100 pF
Cg
002aag379
Fig 42. Slave mode operation of the on-chip oscillator
LPC43xx
L
XTAL1
XTAL2
=
CL
CP
XTAL
RS
CX1
CX2
002aag380
Fig 43. Oscillator modes with external crystal model used for CX1/CX2 evaluation
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
139 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
13.3 RTC oscillator
In the RTC oscillator circuit, only the crystal (XTAL) and the capacitances CRTCX1 and
CRTCX2 need to be connected externally. Typical capacitance values for CRTCX1 and
CRTCX2 are CRTCX1/2 = 20 (typical) 4 pF.
An external clock can be connected to RTCX1 if RTCX2 is left open. The recommended
amplitude of the clock signal is Vi(RMS) = 100 mV to 200 mV with a coupling capacitance of
5 pF to 10 pF.
LPC43xx
RTCX1
RTCX2
XTAL
CRTCX1
CRTCX2
002aah083
Fig 44. RTC 32 kHz oscillator circuit
13.4 XTAL and RTCX Printed Circuit Board (PCB) layout guidelines
Connect the crystal on the PCB as close as possible to the oscillator input and output pins
of the chip. Take care that the load capacitors CX1, CX2, and CX3 in case of third overtone
crystal usage have a common ground plane. Also connect the external components to the
ground plain. To keep the noise coupled in via the PCB as small as possible, make loops
and parasitics as small as possible. Choose smaller values of CX1 and CX2 if parasitics
increase in the PCB layout.
Ensure that no high-speed or high-drive signals are near the RTCX1/2 signals.
13.5 Standard I/O pin configuration
Figure 45 shows the possible pin modes for standard I/O pins with analog input function:
•
•
•
•
•
•
Digital output driver enabled/disabled
Digital input: Pull-up enabled/disabled
Digital input: Pull-down enabled/disabled
Digital input: Repeater mode enabled/disabled
Digital input: Input buffer enabled/disabled
Analog input
The default configuration for standard I/O pins is input buffer disabled and pull-up
enabled. The weak MOS devices provide a drive capability equivalent to pull-up and
pull-down resistors.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
140 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
VDDIO
ESD
enable output driver
data output from core
PIN
slew rate bit EHS
input buffer enable bit EZI
data input to core
glitch
filter
filter select bit ZIF
pull-up enable bit EPUN
ESD
pull-down enable bit EPD
analog I/O
VSSIO
002aah028
The glitch filter rejects pulses of typical 12 ns width.
Fig 45. Standard I/O pin configuration with analog input
13.5.1 Reset pin configuration
Vps
Vps
Vps
Rpu
reset
ESD
20 ns RC
GLITCH FILTER
PIN
ESD
VSS
002aag702
Fig 46. Reset pin configuration
13.5.2 Suggested USB interface solutions
The USB device can be connected to the USB as self-powered device (see Figure 47) or
bus-powered device (see Figure 48).
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
141 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
On the LPC436x, USBn_VBUS pins are 5 V tolerant only when VDDIO is applied and at
operating voltage level. Therefore, if the USBn_VBUS function is connected to the USB
connector and the device is self-powered, the USBn_VBUS pins must be protected for
situations when VDDIO = 0 V.
If VDDIO is always at operating level while VBUS = 5 V, the USBn_VBUS pin can be
connected directly to the VBUS pin on the USB connector.
For systems where VDDIO can be 0 V and VBUS is directly applied to the USBn_VBUS
pins, precautions must be taken to reduce the voltage to below 3.6 V, which is the
maximum allowable voltage on the USBn_VBUS pins in this case.
One method is to use a voltage divider to connect the USBn_VBUS pins to VBUS on the
USB connector. The voltage divider ratio should be such that the USB_VBUS pin will be
greater than 0.7VDDIO to indicate a logic HIGH while below the 3.6 V allowable maximum
voltage.
For the following operating conditions
VBUSmax = 5.25 V
VDDIO = 3.6 V,
the voltage divider should provide a reduction of 3.6 V/5.25 V or ~0.686.
For bus-powered devices, a regulator powered by USB can provide 3.3 V to VDDIO
whenever bus power is present and ensure that power to the USBn_VBUS pins is always
present when the 5 V VBUS signal is applied. See Figure 48.
Remark: Applying 5 V to the USBn_VBUS pins for a short time while the regulator ramps
up might compromise the long-term reliability of the part but does not affect its function.
LPC43xx
VDDIO
R2
R3
USBn_VBUS
VBUS
USB-B
connector
USB
aaa-013458
Fig 47. USB interface on a self-powered device where USBn_VBUS = 5 V
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
142 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
LPC43xx
VDDIO
REGULATOR
USBn_VBUS
VBUS
USB-B
connector
USB
aaa-013459
Fig 48. USB interface on a bus-powered device
Remark: If the VBUS function of the USB1 interface is not connected, configure the pin
function for GPIO using the function control bits in the SYSCON block.
VDDIO
R1
LPC43xx
T2
T1
R2
R3
USBn_VBUS
VBUS
USB-B
connector
USB
aaa-013460
Fig 49. USB interface for USB operating in OTG mode
Remark: In OTG mode, it is important to be able to detect the VBUS level and to charge
and discharge VBUS. This requires adding active devices that disconnect the link when
VDDIO is not present.
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
143 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
14. Package outline
LBGA256: plastic low profile ball grid array package; 256 balls; body 17 x 17 x 1 mm
A
B
D
SOT740-2
ball A1
index area
A2
A
E
A1
detail X
C
e1
e
y
y1 C
∅v M C A B
b
1/2 e
∅w M C
T
R
e
P
N
M
L
K
J
e2
H
G
1/2 e
F
E
D
C
B
A
ball A1
index area
1
3
2
5
4
7
6
9
8
11
10
13
12
15
14
16
X
5
0
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max
A1
A2
b
D
E
e
e1
e2
v
w
y
y1
mm
1.55
0.45
0.35
1.1
0.9
0.55
0.45
17.2
16.8
17.2
16.8
1
15
15
0.25
0.1
0.12
0.35
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
JEITA
SOT740-2
---
MO-192
---
EUROPEAN
PROJECTION
ISSUE DATE
05-06-16
05-08-04
Fig 50. Package outline LBGA256 package
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
144 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
LQFP208; plastic low profile quad flat package; 208 leads; body 28 x 28 x 1.4 mm
SOT459-1
c
y
X
A
105
156
157
104
ZE
e
E HE
(A 3)
A A2 A1
wM
θ
Lp
bp
L
detail X
pin 1 index
208
53
1
52
v M A
ZD
wM
bp
e
D
B
HD
v M B
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
mm
1.6
0.15
0.05
1.45
1.35
0.25
0.27
0.17
0.20
0.09
28.1
27.9
28.1
27.9
0.5
HD
HE
30.15 30.15
29.85 29.85
L
Lp
v
w
y
ZD
ZE
θ
1
0.75
0.45
0.12
0.08
0.08
1.43
1.08
1.43
1.08
7o
o
0
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT459-1
136E30
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-02-06
03-02-20
Fig 51. Package outline of the LQFP208 package
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
145 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
TFBGA100: plastic thin fine-pitch ball grid array package; 100 balls; body 9 x 9 x 0.7 mm
B
D
SOT926-1
A
ball A1
index area
A2
E
A
A1
detail X
e1
e
∅v
∅w
b
1/2 e
C
M
M
C A B
C
y
y1 C
K
J
e
H
G
F
e2
E
D
1/2 e
C
B
A
ball A1
index area
1
2
3
4
5
6
7
8
9
10
X
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max
A1
A2
b
D
E
e
e1
e2
v
w
y
y1
mm
1.2
0.4
0.3
0.8
0.65
0.5
0.4
9.1
8.9
9.1
8.9
0.8
7.2
7.2
0.15
0.05
0.08
0.1
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
JEITA
SOT926-1
---
---
---
EUROPEAN
PROJECTION
ISSUE DATE
05-12-09
05-12-22
Fig 52. Package outline of the TFBGA100 package
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
146 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
15. Soldering
Footprint information for reflow soldering of LBGA256 package
SOT740-2
Hx
P
P
Hy
see detail X
Generic footprint pattern
Refer to the package outline drawing for actual layout
solder land
solder paste deposit
solder land plus solder paste
SL
SP
occupied area
SR
solder resist
detail X
DIMENSIONS in mm
P
SL
SP
SR
1.00
0.450
0.450
0.600
Hx
Hy
17.500 17.500
sot740-2_fr
Fig 53. Reflow soldering of the LBGA256 package
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
147 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Footprint information for reflow soldering of LQFP208 package
SOT459-1
Hx
Gx
P2
Hy
(0.125)
P1
Gy
By
Ay
C
D2 (8×)
D1
Bx
Ax
Generic footprint pattern
Refer to the package outline drawing for actual layout
solder land
occupied area
DIMENSIONS in mm
P1
0.500
P2
Ax
Ay
Bx
By
0.560 31.300 31.300 28.300 28.300
C
D1
D2
1.500
0.280
0.400
Gx
Gy
Hx
Hy
28.500 28.500 31.550 31.550
sot459-1_fr
Fig 54. Reflow soldering of the LQFP208 package
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
148 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Footprint information for reflow soldering of TFBGA100 package
SOT926-1
Hx
P
P
Hy
see detail X
Generic footprint pattern
Refer to the package outline drawing for actual layout
solder land
solder paste deposit
solder land plus solder paste
SL
SP
occupied area
SR
solder resist
detail X
DIMENSIONS in mm
P
SL
SP
SR
Hx
Hy
0.80
0.330
0.400
0.480
9.400
9.400
sot926-1_fr
Fig 55. Reflow soldering of the TFBGA100 package
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
149 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
16. Abbreviations
Table 46.
LPC436X
Product data sheet
Abbreviations
Acronym
Description
ADC
Analog-to-Digital Converter
AHB
Advanced High-performance Bus
APB
Advanced Peripheral Bus
API
Application Programming Interface
BOD
BrownOut Detection
CAN
Controller Area Network
CMAC
Cipher-based Message Authentication Code
CSMA/CD
Carrier Sense Multiple Access with Collision Detection
DAC
Digital-to-Analog Converter
DC-DC
Direct Current-to-Direct Current
DMA
Direct Memory Access
GPIO
General Purpose Input/Output
IRC
Internal RC
IrDA
Infrared Data Association
JTAG
Joint Test Action Group
LCD
Liquid Crystal Display
LSB
Least Significant Bit
MAC
Media Access Control
MCU
MicroController Unit
MIIM
Media Independent Interface Management
n.c.
not connected
OHCI
Open Host Controller Interface
OTG
On-The-Go
PHY
Physical Layer
PLL
Phase-Locked Loop
PMC
Power Mode Control
PWM
Pulse Width Modulator
RIT
Repetitive Interrupt Timer
RMII
Reduced Media Independent Interface
SDRAM
Synchronous Dynamic Random Access Memory
SIMD
Single Instruction Multiple Data
SPI
Serial Peripheral Interface
SSI
Serial Synchronous Interface
SSP
Synchronous Serial Port
UART
Universal Asynchronous Receiver/Transmitter
ULPI
UTMI+ Low Pin Interface
USART
Universal Synchronous Asynchronous Receiver/Transmitter
USB
Universal Serial Bus
UTMI
USB2.0 Transceiver Macrocell Interface
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
150 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
17. References
LPC436X
Product data sheet
[1]
LPC43xx/LPC43Sxx User manual UM10503:
http://www.nxp.com/documents/user_manual/UM10503.pdf
[2]
LPC43xx Errata sheet:
http://www.nxp.com/documents/errata_sheet/ES_LPC43XX.pdf
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
151 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
18. Revision history
Table 47.
Revision history
Document ID
Release date Data sheet status
Change notice Supersedes
LPC436x v.1.2
20160314
-
LPC436x v.1.1
Modifications:
Product data sheet
LPC436x v.1.1
•
Updated Table 32 “Dynamic characteristics: Dynamic external memory interface”:
Read cycle parameters th(D) min value is 2.2 ns and max value is “-”.
•
Fixed the number of ADC channels for LPC4367JET100 in Table 2 “Ordering options”
to 4.
20151111
Product data sheet
2015110041
LPC436x v.1.0
•
Added CIN number, 2015110041 for SSP timing value changes in the change notice
column of the Revision history table.
•
Updated Table 27 “Dynamic characteristics: SSP pins in SPI mode”:
– changed units of Tcy(clk), clock cycle time, SSP slave and master from ns to s.
– removed tv(Q), data output valid time in SPI mode, minimum value of 3 ´ (1/PCLK)
from SSP slave mode.
– added units to td, delay time, for SSP slave and master mode.
LPC436x v.1.0
LPC436X
Product data sheet
20151105
Product data sheet
-
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
-
© NXP Semiconductors N.V. 2016. All rights reserved.
152 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
19. Legal information
19.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
19.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product is
deemed to offer functions and qualities beyond those described in the
Product data sheet.
19.3 Disclaimers
Limited warranty and liability — Information in this document is believed to
be accurate and reliable. However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
LPC436X
Product data sheet
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications
and products using NXP Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or customer product
design. It is customer’s sole responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the customer’s applications and
products planned, as well as for the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
153 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor tested
in accordance with automotive testing or application requirements. NXP
Semiconductors accepts no liability for inclusion and/or use of
non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards, customer
(a) shall use the product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and specifications, and (b)
whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
19.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
20. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
154 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
21. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features and benefits . . . . . . . . . . . . . . . . . . . . 1
3
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4
Ordering information . . . . . . . . . . . . . . . . . . . . . 5
4.1
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 5
5
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6
Pinning information . . . . . . . . . . . . . . . . . . . . . . 7
6.1
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 8
7
Functional description . . . . . . . . . . . . . . . . . . 60
7.1
Architectural overview . . . . . . . . . . . . . . . . . . 60
7.2
ARM Cortex-M4 processor . . . . . . . . . . . . . . . 60
7.3
ARM Cortex-M0 processors . . . . . . . . . . . . . . 60
7.3.1
ARM Cortex-M0 coprocessor . . . . . . . . . . . . . 60
7.3.2
ARM Cortex-M0 subsystem . . . . . . . . . . . . . . 60
7.4
Interprocessor communication . . . . . . . . . . . . 61
7.5
AHB multilayer matrix . . . . . . . . . . . . . . . . . . . 62
7.6
Nested Vectored Interrupt Controller (NVIC) . 63
7.6.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
7.6.2
Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 63
7.7
System Tick timer (SysTick) . . . . . . . . . . . . . . 63
7.8
Event router . . . . . . . . . . . . . . . . . . . . . . . . . . 63
7.9
Global Input Multiplexer Array (GIMA) . . . . . . 64
7.9.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
7.10
On-chip static RAM. . . . . . . . . . . . . . . . . . . . . 64
7.11
On-chip flash memory . . . . . . . . . . . . . . . . . . 64
7.12
EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
7.13
Boot ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
7.14
Memory mapping . . . . . . . . . . . . . . . . . . . . . . 66
7.15
One-Time Programmable (OTP) memory . . . 69
7.16
General Purpose I/O (GPIO) . . . . . . . . . . . . . 69
7.16.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
7.17
Configurable digital peripherals . . . . . . . . . . . 69
7.17.1
SCTimer/PWM . . . . . . . . . . . . . . . . . . . . . . . . 69
7.17.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
7.17.2
Serial GPIO (SGPIO) . . . . . . . . . . . . . . . . . . . 70
7.17.2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
7.18
AHB peripherals . . . . . . . . . . . . . . . . . . . . . . . 71
7.18.1
General Purpose DMA . . . . . . . . . . . . . . . . . 71
7.18.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
7.18.2
SPI Flash Interface (SPIFI). . . . . . . . . . . . . . . 71
7.18.2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
7.18.3
SD/MMC card interface . . . . . . . . . . . . . . . . . 72
7.18.4
External Memory Controller (EMC). . . . . . . . . 72
7.18.4.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.18.5
High-speed USB Host/Device/OTG interface
(USB0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
7.18.5.1
7.18.6
7.18.6.1
7.18.7
7.18.7.1
7.18.8
7.18.8.1
7.19
7.19.1
7.19.1.1
7.19.2
7.19.2.1
7.19.3
7.19.3.1
7.19.4
7.19.4.1
7.19.5
7.19.5.1
7.19.6
7.19.6.1
7.19.7
7.19.7.1
7.20
7.20.1
7.20.1.1
7.20.2
7.20.3
7.20.3.1
7.20.4
7.20.4.1
7.20.5
7.20.5.1
7.21
7.21.1
7.21.1.1
7.21.2
7.21.2.1
7.22
7.22.1
7.22.1.1
7.22.1.2
7.22.2
7.23
7.23.1
7.23.2
7.23.3
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-speed USB Host/Device interface
with ULPI (USB1). . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LCD controller . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital serial peripherals. . . . . . . . . . . . . . . . .
UART1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USART0/2/3 . . . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI serial I/O controller . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SSP serial I/O controller. . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C-bus interface . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2S interface . . . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C_CAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Counter/timers and motor control . . . . . . . . .
General purpose 32-bit timers/external
event counters . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor control PWM . . . . . . . . . . . . . . . . . . . .
Quadrature Encoder Interface (QEI) . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repetitive Interrupt (RI) timer. . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windowed WatchDog Timer (WWDT) . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog peripherals . . . . . . . . . . . . . . . . . . . . .
Analog-to-Digital Converter (ADC0/1) . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital-to-Analog Converter (DAC). . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peripherals in the RTC power domain . . . . . .
RTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Event monitor/recorder . . . . . . . . . . . . . . . . .
Alarm timer. . . . . . . . . . . . . . . . . . . . . . . . . . .
System control . . . . . . . . . . . . . . . . . . . . . . . .
Configuration registers (CREG) . . . . . . . . . . .
System Control Unit (SCU) . . . . . . . . . . . . . .
Clock Generation Unit (CGU) . . . . . . . . . . . .
74
74
74
74
75
75
75
76
76
76
76
76
77
77
77
77
78
78
78
79
79
79
79
79
80
80
80
80
81
81
81
81
82
82
82
82
82
82
82
82
83
83
83
83
84
84
continued >>
LPC436X
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 1.2 — 14 March 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
155 of 156
LPC436x
NXP Semiconductors
32-bit ARM Cortex-M4/M0 microcontroller
7.23.4
7.23.5
7.23.6
7.23.7
7.23.8
7.23.9
7.23.10
7.23.11
7.24
8
9
10
10.1
10.2
10.3
10.4
11
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
11.9
11.10
11.11
11.12
11.13
11.14
11.15
11.16
11.17
11.18
11.19
11.20
11.21
12
13
13.1
13.2
13.3
13.4
13.5
13.5.1
13.5.2
14
Internal RC oscillator (IRC). . . . . . . . . . . . . . . 84
PLL0USB (for USB0) . . . . . . . . . . . . . . . . . . . 84
PLL0AUDIO (for audio) . . . . . . . . . . . . . . . . . 84
System PLL1 . . . . . . . . . . . . . . . . . . . . . . . . . 85
Reset Generation Unit (RGU). . . . . . . . . . . . . 85
Power Management Controller (PMC) . . . . . . 85
Power control . . . . . . . . . . . . . . . . . . . . . . . . . 86
Code security (Code Read Protection - CRP) 87
Serial Wire Debug/JTAG. . . . . . . . . . . . . . . . . 87
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 89
Thermal characteristics . . . . . . . . . . . . . . . . . 90
Static characteristics. . . . . . . . . . . . . . . . . . . . 91
Power consumption . . . . . . . . . . . . . . . . . . . . 98
Peripheral power consumption . . . . . . . . . . . 101
Electrical pin characteristics . . . . . . . . . . . . . 103
BOD and band gap static characteristics . . . 107
Dynamic characteristics . . . . . . . . . . . . . . . . 108
Flash/EEPROM memory . . . . . . . . . . . . . . . 108
Wake-up times . . . . . . . . . . . . . . . . . . . . . . . 109
External clock for oscillator in slave mode . . 109
Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . 110
IRC oscillator . . . . . . . . . . . . . . . . . . . . . . . . 110
RTC oscillator . . . . . . . . . . . . . . . . . . . . . . . . 110
GPCLKIN . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
I/O pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
I2C-bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
I2S-bus interface . . . . . . . . . . . . . . . . . . . . . . 113
USART interface. . . . . . . . . . . . . . . . . . . . . . 114
SSP interface . . . . . . . . . . . . . . . . . . . . . . . . 116
SPI interface . . . . . . . . . . . . . . . . . . . . . . . . . 119
SSP/SPI timing diagrams . . . . . . . . . . . . . . . 120
SPIFI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
SGPIO timing . . . . . . . . . . . . . . . . . . . . . . . . 122
External memory interface . . . . . . . . . . . . . . 124
USB interface . . . . . . . . . . . . . . . . . . . . . . . 129
Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
SD/MMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
ADC/DAC electrical characteristics . . . . . . . 133
Application information. . . . . . . . . . . . . . . . . 136
LCD panel signal usage . . . . . . . . . . . . . . . . 136
Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . 138
RTC oscillator . . . . . . . . . . . . . . . . . . . . . . . . 140
XTAL and RTCX Printed Circuit Board (PCB)
layout guidelines . . . . . . . . . . . . . . . . . . . . . . 140
Standard I/O pin configuration . . . . . . . . . . . 140
Reset pin configuration . . . . . . . . . . . . . . . . . 141
Suggested USB interface solutions . . . . . . . 141
Package outline . . . . . . . . . . . . . . . . . . . . . . . 144
15
16
17
18
19
19.1
19.2
19.3
19.4
20
21
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . .
References. . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . .
Legal information . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information . . . . . . . . . . . . . . . . . . .
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
147
150
151
152
153
153
153
153
154
154
155
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP Semiconductors N.V. 2016.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 14 March 2016
Document identifier: LPC436X