EMC6D102 Fan Control Device with Hardware Monitoring and Acoustic Noise Reduction Features PRODUCT FEATURES Data Brief 3.3 Volt Operation (5 Volt Tolerant Input Buffers) SMBus 2.0 compliant interface (Fixed, Not Discoverable) With Three Slave Address Options Fan Control — Monitor Power supplies (+2.5V, +5V, +12V, Vccp, and VCC) — Individual status and enable bits per voltage input — Limit Comparison of all Monitored Values — Interrupt Pin for out-of-limit Voltage Indication — Supports 4 programmable voltage averaging modes — 2 monitoring modes: Continuous or Cycle (Power Saving mode) — Offers 2 Low Power Modes when monitoring is off: Sleep and Shutdown — — — — PWM (Pulse width Modulation) Outputs (3) Fan Tachometer Inputs (4) Individual status and enable bits per tach input Programmable automatic fan control based on temperature — Fan ramp rate control for acoustic noise reduction Temperature Monitor — Monitoring of Two Remote Thermal Diodes (+/- 3 deg C accuracy) — Internal Ambient Temperature Measurement — Limit Comparison of all Monitored Values — Individual status and enable bits per thermal input — Interrupt Pin for out-of-limit Temperature Indication — Configurable offset for internal or external temperature channels. — Supports 4 programmable temperature averaging modes — 2 monitoring modes: Continuous or Cycle (Power Saving mode) — Offers 2 Low Power Modes when monitoring is off: Sleep and Shutdown SMSC EMC6D102 Voltage Monitor 5 VID (Voltage Identification) inputs XOR Tree test mode 24-pin, SSOP Lead-Free RoHS Compliant package PRODUCT PREVIEW Revision 0.4 (09-25-07) Fan Control Device with Hardware Monitoring and Acoustic Noise Reduction Features ORDER NUMBERS: EMC6D102-CZC FOR 24 PIN, SSOP LEAD-FREE ROHS COMPLIANT PACKAGE EMC6D102-CZC-TR FOR 24 PIN, SSOP LEAD-FREE ROHS COMPLIANT PACKAGE 80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123 Copyright © 2007 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Revision 0.4 (09-25-07) 2 PRODUCT PREVIEW SMSC EMC6D102 Fan Control Device with Hardware Monitoring and Acoustic Noise Reduction Features General Description The EMC6D102 is an environmental monitoring device with automatic fan control capability. This ACPI compliant device provides hardware monitoring for up to five voltages and three thermal zones, measures the speed of up to four fans, and controls the speed of multiple DC fans using Pulse Width Modulator (PWM) outputs. The EMC6D102 hardware monitor provides analog inputs for monitoring external voltages of +2.5V, +5V, +12V and Vccp. This device has the capability to monitor its own internal VCC power supply, which may be connected to either main power (VCC) or the suspend power well (VTR). In addition to monitoring the processor voltage, VID inputs are available to identify the voltage specification. External components are not required for voltage scaling or similar treatment. The EMC6D102 hardware monitor includes support for monitoring three thermal zones: two external and one internal. The external temperatures are measured via thermal diode inputs capable of monitoring remote devices. In addition, they are equipped with an ambient temperature sensor for measuring the internal temperature. Pulse Width Modulators (PWM) control the speed of the fans by varying the output duty cycle of the PWM. Each PWM can be associated with any or all of the thermal zones monitored. As the temperature of the associated zone varies, the PWM duty cycle is adjusted accordingly. The Ramp Rate Control feature controls the rate of change of the PWM output, thereby reducing system noise created by changing the fan speed. The speed of each fan is monitored by a Fan Tachometer input. The measured values are compared to values stored in Limit Registers to detect if a fan has stalled or seized. Fan speed may be under host software control or automatic. In host control mode, the host software continuously monitors temperature and fan speed registers, makes decisions as to desired fan speed and sets the PWM’s to drive the required fan speed. This device offers an interrupt output signal (INT#), which may be used to interrupt the host on out-of-limit temperature or voltage condition enabling an ACPI response as opposed to the host software continuously monitoring status. In auto “zone” mode, the logic continuously monitors the temperature and fan speeds and adjusts speeds without intervention from the host CPU. Fan speed is adjusted according to an algorithm using the temperature measured in the selected zone, the high and low limits set by the user, and the current fan speed. SMSC EMC6D102 3 PRODUCT PREVIEW Revision 0.4 (09-25-07) Fan Control Device with Hardware Monitoring and Acoustic Noise Reduction Features Pin Layout Diagram SDA 1 24 PWM1/xTest Out SCL 2 23 Vccp VSS 3 22 2.5V VCC 4 21 12V VID0 5 20 5V VID1 6 19 VID4 EMC6D102 VID2 7 18 Remote1+ VID3 8 17 Remote1- TACH3/INT# 9 16 Remote2+ PWM2/INT# 10 15 Remote2- TACH1 11 14 TACH4/Address Select TACH2 12 13 PWM3/Address Enable Figure 1 EMC6D102 Pin Diagram Revision 0.4 (09-25-07) 4 PRODUCT PREVIEW SMSC EMC6D102 Fan Control Device with Hardware Monitoring and Acoustic Noise Reduction Features Package Outline Figure 2 24-Pin SSOP Package Outline, 0.150” Wide Body, 0.025” Pitch Table 1 24-pin SSOP Package Parameters A A1 A2 D E E1 H L e è W ccc MIN NOMINAL MAX REMARKS 0.053 0.004 ~ 0.337 0.228 0.150 0.007 0.016 ~ ~ ~ ~ ~ ~ ~ 0.025 0.025 Basic ~ 0.010 ~ 0.069 0.010 0.061 0.344 0.244 0.157 0.010 0.050 Overall Package Height Standoff Body Thickness X Body Size Y Span Y body Size Lead Frame Thickness Lead Foot Length Lead Pitch Lead Foot Angle Lead Width Coplanarity 0o 0.008 ~ 8o 0.012 0.004 Notes: 1. Controlling Unit: inch. 2. Tolerance on the true position of the leads is ± 0.0035 inches maximum. 3. Package body dimensions D and E1 do not include the mold protrusion. Maximum mold protrusion is 0.006 inches for ends, and 0.010 inches for sides. 4. Dimension for foot length L measured at the gauge plane 0.010 inches above the seating plane. 5. Details of pin 1 identifier are optional but must be located within the zone indicated. SMSC EMC6D102 5 PRODUCT PREVIEW Revision 0.4 (09-25-07)