MCP23018 DATA SHEET (09/29/2008) DOWNLOAD

MCP23018/MCP23S18
16-Bit I/O Expander with Open-Drain Outputs
Features
• Configurable interrupt source:
- Interrupt-on-change from configured defaults
or pin change
• Polarity inversion register to configure the polarity
of the input port data
• External reset input
• Low standby current:
- 1 µA (-40°C ≤ TA ≤ +85°C)
- 6 µA (+85°C ≤ TA ≤ +125°C)
• Operating voltage:
- 1.8V to 5.5V
• 16-bit remote bidirectional I/O port:
- I/O pins default to input
• Open-drain outputs:
- 5.5V tolerant
- 25 mA sink capable (per pin)
- 400 mA total
• High-speed I2C™ interface: (MCP23018)
- 100 kHz
- 400 kHz
- 3.4 MHz
• High-speed SPI interface: (MCP23S18)
- 10 MHz: 2.7V ≤ VDD ≤ 5.5V
• Single hardware address pin: (MCP23018)
- Voltage input to allow up to eight devices on
the bus
• Configurable interrupt output pins:
- Configurable as active-high, active-low or
open-drain
Packages
28-pin PDIP (300 mil)
28-pin SOIC (300 mil)
24-pin SSOP (MCP23018 only)
24-pin QFN (4x4 [mm])
Block Diagram
MCP23S18
CS
SCK
SI
SO
SPI
Open-drain
MCP23018
SCL
SDA
I2C
Serializer/
Deserializer
GPIO
ADDR
Multi-bit
Decode
RESET
INTA
INTB
Control
16
Interrupt
Logic
8
GPIO
Configuration/
Control
Registers
© 2008 Microchip Technology Inc.
GPB7
GPB6
GPB5
GPB4
GPB3
GPB2
GPB1
GPB0
GPA7
GPA6
GPA5
GPA4
GPA3
GPA2
GPA1
GPA0
DS22103A-page 1
MCP23018/MCP23S18
Package Types:
MCP23018
PDIP/SOIC
VSS
NC
GPB0
GPB1
GPB2
GPB3
GPB4
GPB5
GPB6
GPB7
VDD
SCL
SDA
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SSOP
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VSS
GPB0
GPB1
GPB2
GPB3
GPB4
GPB5
GPB6
GPB7
VDD
SCL
SDA
NC
GPA7
GPA6
GPA5
GPA4
GPA3
GPA2
GPA1
GPA0
INTA
INTB
NC
RESET
ADDR
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
GPA7
GPA6
GPA5
GPA4
GPA3
GPA2
GPA1
GPA0
INTA
INTB
RESET
ADDR
QFN
18 GPA3
GPB2 2
17 GPA2
EP
25
GPB3 3
16 GPA1
ADDR 11
13 INTB
RESET 12
GPB6 6
SCL 9
14 INTA
SDA 10
15 GPA0
GPB5 5
VDD 8
GPB4 4
GPB7 7
DS22103A-page 2
GPA4 19
GPA5 20
GPA6 21
VSS 23
GPA7 22
GPB0 24
GPB1 1
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
Package Types:
MCP23S18
PDIP/SOIC
GPB1 1
GPA4 19
GPA5 20
GPA6 21
18 GPA3
GPB2 2
17 GPA2
EP
25
GPB3 3
16 GPA1
SO 12
13 RESET
SI 11
14 INTA *
GPB6 6
SCK 10
GPB5 5
CS 9
15 GPA0
VDD 8
GPB4 4
GPB7 7
NC
GPA7
GPA6
GPA5
GPA4
GPA3
GPA2
GPA1
GPA0
INTA
INTB
NC
RESET
SO
GPA7 22
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VSS 23
1
2
3
4
5
6
7
8
9
10
11
12
13
14
GPB0 24
VSS
NC
GPB0
GPB1
GPB2
GPB3
GPB4
GPB5
GPB6
GPB7
VDD
CS
SCK
SI
QFN *
* INTB is not bonded out. Can be controlled in
IOCON.MIRROR
© 2008 Microchip Technology Inc.
DS22103A-page 3
MCP23018/MCP23S18
1.0
DEVICE OVERVIEW
The MCP23X18 device provides 16-bit, general purpose parallel I/O expansion for I2C bus or SPI
applications. The two devices differ only in the serial
interface.
• MCP23018 - I2C interface
• MCP23S18 - SPI interface
The MCP23X18 consists of multiple 8-bit configuration
registers for input, output and polarity selection. The
system master can enable the I/Os as either inputs or
outputs by writing the I/O configuration bits. The data
for each input or output is kept in the corresponding
input or output register. The polarity of the input port
register can be inverted with the polarity inversion
register. All registers can be read by the system master.
The 16-bit I/O port functionally consists of two (2) 8-bit
ports (PORTA and PORTB). The MCP23X18 can be
configured to operate in 8-bit mode or 16-bit mode via
IOCON.BANK.
DS22103A-page 4
There are two interrupt pins, INTA and INTB which can
be associated with their respective ports, or can be
logically OR’ed together so both pins will activate if
either port causes an interrupt.
The interrupt output can be configured to activate
under two conditions (mutually exclusive):
1.
2.
When any input state differs from its
corresponding input port register state. This is
used to indicate to the system master that an
input state has changed.
When an input state differs from a preconfigured register value (DEFVAL register).
The Interrupt Capture register captures port values at
the time of the interrupt, thereby saving the condition
that caused the interrupt.
The Power-on Reset (POR) sets the registers to their
default values and initializes the device state machine.
The hardware address pin is used to determine the
device address.
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
1.1
Pin Descriptions
I2C PINOUT DESCRIPTION (MCP23018)
TABLE 1-1:
28L
PDIP/
SOIC
24L
QFN
GPB0
3
24
2
I/O
GPB1
4
1
3
I/O
GPB2
5
2
4
I/O
GPB3
6
3
5
I/O
GPB4
7
4
6
I/O
GPB5
8
5
7
I/O
GPB6
9
6
8
I/O
GPB7
10
7
9
I/O
VDD
VSS
SCL
SDA
ADDR
RESET
INTB
11
1
12
13
15
16
18
8
23
9
10
11
12
13
10
1
11
12
13
14
15
P
P
I
I/O
I
I
O
INTA
19
14
16
O
GPA0
20
15
17
I/O
GPA1
21
16
18
I/O
GPA2
22
17
19
I/O
GPA3
23
18
20
I/O
GPA4
24
19
21
I/O
GPA5
25
20
22
I/O
GPA6
26
21
23
I/O
GPA7
27
22
24
I/O
2, 14,
17, 28
—
—
—
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Power
Ground
Serial clock input
Serial data I/O
Hardware address pin allows up to 8 slave devices on the bus
Hardware reset
Interrupt output for port B. Can be configured as active high, active low, or
open drain.
Interrupt output for port A. Can be configured as active high, active low, or
open drain.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be
enabled for interrupt on change, and/or internal pull-up resistor.
Not connected
25
—
Exposed Thermal Pad (EP). Do not electrically connect, or connect to VSS.
Pin
Name
NC
EP
24L
Pin
SSOP Type
© 2008 Microchip Technology Inc.
Standard Function
DS22103A-page 5
MCP23018/MCP23S18
TABLE 1-2:
SPI PINOUT DESCRIPTION (MCP23S18)
28L
PDIP/
SOIC
24L
QFN
Pin
Type
GPB0
3
24
I/O
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
GPB1
4
1
I/O
GPB2
5
2
I/O
GPB3
6
3
I/O
GPB4
7
4
I/O
GPB5
8
5
I/O
GPB6
9
6
I/O
GPB7
10
7
I/O
VDD
VSS
CS
SCK
SI
SO
RESET
INTB
11
1
12
13
14
15
16
18
8
23
9
10
11
12
13
—
P
P
I
I
I
O
I
O
INTA
19
14
O
GPA0
20
15
I/O
GPA1
21
16
I/O
GPA2
22
17
I/O
GPA3
23
18
I/O
GPA4
24
19
I/O
GPA5
25
20
I/O
GPA6
26
21
I/O
GPA7
27
22
I/O
2, 17,
28
—
—
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Power (high current capable)
Ground (high current capable)
Chip select
Serial clock input
Serial data input
Serial data out
Hardware reset (must be externally biased)
Interrupt output for port B. Can be configured as active high, active low, or open
drain.
Interrupt output for port A. Can be configured as active high, active low, or open
drain.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Bidirectional I/O Pin (5.5 volt tolerant inputs; open-drain outputs). Can be enabled
for interrupt on change, and/or internal pull-up resistor.
Not connected
Pin
Name
NC
EP
DS22103A-page 6
25
—
Standard Function
Exposed Thermal Pad (EP). Do not electrically connect, or connect to VSS.
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
1.2
Power-on Reset (POR)
The on-chip POR circuit holds the device in reset until
VDD has reached a high enough voltage to deactivate
the POR circuit (i.e., release the device from reset).
The maximum VDD rise time is specified in the
electrical specification section.
When the device exits the POR condition (releases
reset), device operating parameters (i.e., voltage,
temperature, serial bus frequency, etc.) must be met to
ensure proper operation.
1.3
Serial Interface
This block handles the functionality of the I2C
(MCP23018) or SPI (MCP23S18) interface protocol.
The MCP23X18 contains twenty two (22) individual
registers (eleven [11] register pairs) which can be
addressed through the Serial Interface block (Table 11).
TABLE 1-1:
REGISTER ADDRESSES
Address
Address
Access to:
IOCON.BANK = 1 IOCON.BANK = 0
00h
10h
01h
11h
02h
12h
03h
13h
04h
14h
05h
15h
06h
16h
07h
17h
08h
18h
09h
19h
0Ah
1Ah
1.3.1
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
IODIRA
IODIRB
IPOLA
IPOLB
GPINTENA
GPINTENB
DEFVALA
DEFVALB
INTCONA
INTCONB
IOCON
IOCON
GPPUA
GPPUB
INTFA
INTFB
INTCAPA
INTCAPB
GPIOA
GPIOB
OLATA
OLATB
BYTE MODE AND SEQUENTIAL
MODE
The MCP23X18 has the ability to operate in “Byte
Mode” or “Sequential Mode” (IOCON.SEQOP). Byte
mode and sequential mode are not to be confused with
I2C byte operations and sequential operations. The
© 2008 Microchip Technology Inc.
modes explained here relate to the device’s internal
address pointer and whether or not it is incremented
after each byte is clocked on the serial interface.
Byte Mode disables automatic address pointer incrementing. When operating in Byte Mode, the
MCP23X18 does not increment its internal address
counter after each byte during the data transfer. This
gives the ability to continually access the same address
by providing extra clocks (without additional control
bytes). This is useful for polling the GPIO register for
data changes or for continually writing to the output
latches.
A special mode (Byte Mode with IOCON.BANK = 0)
causes the address pointer to toggle between associated A/B register pairs. For example, if the BANK bit is
cleared and the address pointer is initially set to
address 12h (GPIOA) or 13h (GPIOB), the pointer will
toggle between GPIOA and GPIOB. Note, the address
pointer can initially point to either address in the register pair.
Sequential Mode enables automatic address pointer
incrementing. When operating in Sequential Mode, the
MCP23X18 increments its address counter after each
byte during the data transfer. The address pointer automatically rolls over to address 00h after accessing the
last register.
These two modes are not to be confused with single
writes/reads and continuous writes/reads which are
serial protocol sequences. For example, the device
may be configured for Byte Mode and the master may
perform a continuous read. In this case, the
MCP23X18 would not increment the address pointer
and would repeatedly drive data from the same location.
1.3.2
1.3.2.1
I2C INTERFACE
I2C Write Operation
The I2C write operation includes the control byte and
register address sequence, as shown in the bottom of
Figure 1-1. This sequence is followed by eight bits of
data from the master and an Acknowledge (ACK) from
the MCP23018. The operation is ended with a stop (P)
or restart (SR) condition being generated by the master.
Data is written to the MCP23018 after every byte transfer. If a stop or restart condition is generated during a
data transfer, the data will not be written to the
MCP23018.
Both “byte mode” and “sequential mode” are supported
by the MCP23018. If sequential mode is enabled
(default), the MCP23018 increments its address
counter after each ACK during the data transfer.
DS22103A-page 7
MCP23018/MCP23S18
1.3.2.2
I2C Read Operation
1.3.3
SPI INTERFACE
2
I C read operations include the control byte sequence,
as shown in the bottom of Figure 1-1. This sequence is
followed by another control byte (including the Start
condition and ACK) with the R/W bit equal to a logic
one (R/W = 1). The MCP23018 then transmits the data
contained in the addressed register. The sequence is
ended with the master generating a Stop or Restart
condition.
1.3.2.3
I2C Sequential Write/Read
For sequential operations (Write or Read), instead of
transmitting a Stop or Restart condition after the data
transfer, the master clocks the next byte pointed to by
the address pointer (see Section 1.3.1 “Byte Mode
and Sequential Mode” for details regarding sequential
operation control).
The sequence ends with the master sending a Stop or
Restart condition.
The MCP23018 address pointer will roll over to
address zero after reaching the last register address.
Refer to Figure 1-1.
1.3.3.1
SPI Write Operation
The SPI write operation is started by lowering CS. The
write command (slave address with R/W bit cleared) is
then clocked into the device. The opcode is followed by
an address and at least one data byte.
1.3.3.2
SPI Read Operation
The SPI read operation is started by lowering CS. The
SPI read command (slave address with R/W bit set) is
then clocked into the device. The opcode is followed by
an address, with at least one data byte being clocked
out of the device.
1.3.3.3
SPI Sequential Write/Read
For sequential operations, instead of deselecting the
device by raising CS, the master clocks the next byte
pointed to by the address pointer. (see Section 1.3.1
“Byte Mode and Sequential Mode” for details regarding sequential operation control).
The sequence ends by the raising of CS.
The MCP23S18 address pointer will roll over to
address zero after reaching the last register address.
DS22103A-page 8
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
MCP23018 I2C™ DEVICE PROTOCOL
FIGURE 1-1:
S - Start
SR - Restart
S
OP
DIN
W ADDR
DIN
....
P
P - Stop
w
- Write
DOUT ....
SR
OP
R
OP
W ADDR ....
DOUT
P
DIN
P
R - Read
OP
- Device opcode
SR
ADDR
- Device address
P
DOUT
- Data out from MCP23018
DIN
- Data in to MCP23018
OP
S
DOUT
R
SR
SR
OP
W
OP
DOUT
....
R
ADDR
P
DOUT
....
DOUT
P
DIN
....
DIN
P
P
Byte and Sequential Write
Byte
S
OP
W
ADDR
DIN
Sequential
S
OP
W ADDR
DIN
P
....
DIN
P
Byte and Sequential Read
Byte S
OP
W ADDR
SR
OP
R
DOUT
Sequential S
OP
W ADDR
SR
OP
R
DOUT
© 2008 Microchip Technology Inc.
P
....
DOUT
P
DS22103A-page 9
MCP23018/MCP23S18
1.4
Multi-bit Address Decoder
The ADDR pin is used to set the slave address of the
MCP23018 (I2C only) to allow up to eight devices on
the bus using only a single pin. Typically, this would
require three pins.
The multi-bit Address Decoder employs a basic FLASH
ADC architecture (Figure 1-4). The seven comparators
generate 8 unique values based on the analog input.
This value is converted to a 3-bit code which corresponds to the address bits (A2, A1, A0) in the serial
OPCODE.
Sequence
timings):
1.
of
Operation
(see
Figure 1-5
for
Upon power up (after VDD stabilizes) the module
becomes active after time tADEN. Note, the analog value on the ADDR pin must be stable
before this point to ensure accurate address
assignment.
FIGURE 1-2:
2.
3.
The 3-bit address is latched after tADDRLAT.
The module powers down after the first rising
edge of the serial clock is detected (tADDIS).
Once the address bits are latched, the device will keep
the slave address until a POR or reset condition
occurs.
1.4.1
CALCULATING VOLTAGE ON ADDR
When calculating the required voltage on the ADDR pin
(V2), the set point should be the mid-point of the LSb of
the ADC.
The examples in Figure 1-2 and Figure 1-3 show how
to determine the mid point voltage (V2) and the range
of voltages based on a voltage divider circuit. The
maximum tolerance is 20%, however, it is recommended to use 5% tolerance worst case (10% total tolerance).
VOLTAGE DIVIDER EXAMPLE
VDD
ADDR
VDD
MCP23018
A0
R1
A1
A2
V2
R2
VSS
VSS
DS22103A-page 10
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
FIGURE 1-3:
VOLTAGE AND CODE EXAMPLE
Assume:
n = A2, A1, A0 in opcode
ratio = R2/(R1+R2)
V2 = voltage on ADDR pin
V2(min) = V2 - (VDD/8) x %tolerance
V2(max) = V2 + (VDD/8) x %tolerance
n
R2=2n+1
0
1
2
3
4
5
6
7
n
1
3
5
7
9
11
13
15
R2=2n+1
0
1
2
3
4
5
6
7
n
1
3
5
7
9
11
13
15
R2=2n+1
0
1
2
3
4
5
6
7
n
1
3
5
7
9
11
13
15
R2=2n+1
0
1
2
3
4
5
6
7
© 2008 Microchip Technology Inc.
1
3
5
7
9
11
13
15
10% Tolerance (total)
VDD= 1.8
R1=16-R2 R2/(R1+R2)
V2
V2(min)
V2(max)
0.113
15
0.0625
0.00
0.14
13
0.1875
0.32
0.36
0.338
11
0.3125
0.54
0.59
0.563
0.788
9
0.4375
0.77
0.81
7
0.5625
0.99
1.04
1.013
1.238
5
0.6875
1.22
1.26
3
0.8125
1.44
1.49
1.463
1
0.9375
1.67
1.80
1.688
10% Tolerance (total)
VDD= 2.7
R1=16-R2 R2/(R1+R2)
V2
V2(min)
V2(max)
0.169
15
0.0625
0.00
0.19
13
0.1875
0.48
0.53
0.506
0.844
11
0.3125
0.82
0.87
9
0.4375
1.16
1.20
1.181
7
0.5625
1.50
1.54
1.519
1.856
5
0.6875
1.83
1.88
3
0.8125
2.17
2.22
2.194
2.531
1
0.9375
2.51
2.70
VDD= 3.3
R1=16-R2 R2/(R1+R2)
V2
15
0.0625
0.206
13
0.1875
0.619
1.031
11
0.3125
9
0.4375
1.444
1.856
7
0.5625
5
0.6875
2.269
2.681
3
0.8125
1
0.9375
3.094
10% Tolerance (total)
V2(min)
V2(max)
0.00
0.23
0.60
0.64
1.01
1.05
1.42
1.47
1.83
1.88
2.25
2.29
2.66
2.70
3.07
3.30
VDD= 5.5
10% Tolerance (total)
R1=16-R2 R2/(R1+R2)
V2
V2(min)
V2(max)
15
0.0625
0.00
0.37
0.344
1.031
13
0.1875
1.01
1.05
11
0.3125
1.70
1.74
1.719
9
0.4375
2.38
2.43
2.406
3.094
7
0.5625
3.07
3.12
5
0.6875
3.76
3.80
3.781
4.469
3
0.8125
4.45
4.49
1
0.9375
5.13
5.50
5.156
DS22103A-page 11
MCP23018/MCP23S18
FIGURE 1-4:
FLASH ADC BLOCK DIAGRAM
VDD
analog_in
addr_out[6]
adc_en
addr_out[5]
d
adc_en
adc_en
addr_out[4]
q
addr[6:0]
i2c_addr[2:0]
en
reset
'0'
set
d
q
adc_en
adc_en
addr_out[3]
i2c_clk
adc_en
addr_out[2]
adc_en
addr_out[1]
adc_en
addr_out[0]
adc_en
adc_en
gnd
DS22103A-page 12
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
FIGURE 1-5:
HARDWARE ADDRESS DECODE TIMING
tADEN
VDD
tADDRLAT
adc_en
i2c_addr[2:0]
tADDIS
i2c_clk
1.4.2
ADDRESSING I2C DEVICES
(MCP23018)
The MCP23018 is a slave I2C device that supports 7bit slave addressing, with the read/write bit filling out
the control byte. The slave address contains four fixed
bits and three user-defined hardware address bits (pins
A2, A1, and A0). Figure 1-6 shows the control byte
format.
1.4.3
ADDRESSING SPI DEVICES
(MCP23S18)
The MCP23S18 is a slave SPI device. The slave
address contains seven fixed bits(no address bits) with
the read/write bit filling out the control byte. Figure 1-7
shows the control byte format.
I2C™ CONTROL BYTE
FORMAT
FIGURE 1-6:
Control Byte
S
0
1
0
0
A2 A1 A0 R/W ACK
Slave Address
R/W bit
ACK bit
Start
bit
R/W = 0 = write
R/W = 1 = read
FIGURE 1-7:
SPI CONTROL BYTE
FORMAT
CS
Control Byte
0
1
0
0
0
0
0
R/W
Slave Address
R/W bit
R/W = 0 = write
R/W = 1 = read
© 2008 Microchip Technology Inc.
DS22103A-page 13
MCP23018/MCP23S18
I2C™ ADDRESSING REGISTERS
FIGURE 1-8:
S
0
1
0
0
A2 A1 A0
0
ACK
A7
A6
A5
A4
A3
A2
A1
A0
ACK
R/W = 0
Device Opcode
Register Address
The ACKs are provided by the MCP23X18.
FIGURE 1-9:
SPI ADDRESSING REGISTERS
CS
0
1
0
0
0
Device Opcode
DS22103A-page 14
0
0
R/W
A7
A6
A5
A4
A3
A2
A1
A0
Register Address
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
1.5
GPIO Port
The pull up resistors are individually configured and
can be enabled when the pin is cofigured as an input or
output.
The GPIO module is a general purpose 16-bit wide
bidirectional port which is functionally split into two (2)
8-bit wide ports.
Reading the GPIOn register reads the value on the
port. Reading the OLATn register only reads the
latches, not the actual value on the port.
The outputs are open-drain.
The GPIO module contains the data ports (GPIOn),
internal pull up resistors and the Output Latches
(OLATn).
TABLE 1-2:
Writing to the GPIOn register actually causes a write to
the latches (OLATn). Writing to the OLATn register
forces the associated output drivers to drive to the level
in OLATn. Pins configured as inputs turn off the associated output driver and put it in high-impedance.
SUMMARY OF REGISTERS ASSOCIATED WITH THE GPIO PORTS (BANK = 1)
Address
(hex)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
POR/RST
value
IODIRA
00
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
1111 1111
IPOLA
01
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
0000 0000
GPINTENA
02
GPINT7
GPINT6
GPINT5
GPINT4
GPINT3
GPINT2
GPINT1
GPINT0
0000 0000
GPPUA
06
PU7
PU6
PU5
PU4
PU3
PU2
PU1
PU0
0000 0000
GPIOA
09
GP7
GP6
GP5
GP4
GP3
GP2
GP1
GP0
0000 0000
OLATA
0A
OL7
OL6
OL5
OL4
OL3
OL2
OL1
OL0
0000 0000
IODIRB
10
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
1111 1111
IPOLB
11
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
0000 0000
GPINTENB
12
GPINT7
GPINT6
GPINT5
GPINT4
GPINT3
GPINT2
GPINT1
GPINT0
0000 0000
GPPUB
16
PU7
PU6
PU5
PU4
PU3
PU2
PU1
PU0
0000 0000
GPIOB
19
GP7
GP6
GP5
GP4
GP3
GP2
GP1
GP0
0000 0000
OLATB
1A
OL7
OL6
OL5
OL4
OL3
OL2
OL1
OL0
0000 0000
Register
Name
TABLE 1-3:
Register
Name
SUMMARY OF REGISTERS ASSOCIATED WITH THE GPIO PORTS (BANK = 0)
Address
(hex)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
POR/RST
value
IODIRA
00
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
1111 1111
IODIRB
01
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
1111 1111
IPOLA
02
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
0000 0000
IPOLB
03
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
0000 0000
GPINTENA
04
GPINT7
GPINT6
GPINT5
GPINT4
GPINT3
GPINT2
GPINT1
GPINT0
0000 0000
GPINTENB
05
GPINT7
GPINT6
GPINT5
GPINT4
GPINT3
GPINT2
GPINT1
GPINT0
0000 0000
GPPUA
0C
PU7
PU6
PU5
PU4
PU3
PU2
PU1
PU0
0000 0000
GPPUB
0D
PU7
PU6
PU5
PU4
PU3
PU2
PU1
PU0
0000 0000
GPIOA
12
GP7
GP6
GP5
GP4
GP3
GP2
GP1
GP0
0000 0000
GPIOB
13
GP7
GP6
GP5
GP4
GP3
GP2
GP1
GP0
0000 0000
OLATA
14
OL7
OL6
OL5
OL4
OL3
OL2
OL1
OL0
0000 0000
OLATB
15
OL7
OL6
OL5
OL4
OL3
OL2
OL1
OL0
0000 0000
© 2008 Microchip Technology Inc.
DS22103A-page 15
MCP23018/MCP23S18
1.6
Configuration and Control
Registers
with Port A and ten (10) are associated with Port B.
One register (IOCON) is shared between the two ports.
The Port A registers are identical to the Port B registers, therefore, they will be referred to without differentiating between the port designation (i.e., they will not
have the “A” or “B” designator assigned) in the register
tables.
There are twenty two (22) registers associated with the
MCP23X18 as shown in Table 1-4 and Table 1-5. The
two tables show the register mapping with the two
BANK bit values. Ten (10) registers are associated
TABLE 1-4:
CONTROL REGISTER SUMMARY (IOCON.BANK = 1)
Address
(hex)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
POR/RST
value
IODIRA
00
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
1111 1111
IPOLA
01
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
0000 0000
GPINTENA
02
GPINT7
GPINT6
GPINT5
GPINT4
GPINT3
GPINT2
GPINT1
GPINT0
0000 0000
DEFVALA
03
DEF7
DEF6
DEF5
DEF4
DEF3
DEF2
DEF1
DEF0
0000 0000
INTCONA
04
IOC7
IOC6
IOC5
IOC4
IOC3
IOC2
IOC1
IOC0
0000 0000
IOCON
05
BANK
MIRROR
SEQOP
—
—
ODR
INTPOL
INTCC
0000 0000
Register
Name
GPPUA
06
PU7
PU6
PU5
PU4
PU3
PU2
PU1
PU0
0000 0000
INTFA
07
INT7
INT6
INT5
INT4
INT3
INT2
INT1
INTO
0000 0000
INTCAPA
08
ICP7
ICP6
ICP5
ICP4
ICP3
ICP2
ICP1
ICP0
0000 0000
GPIOA
09
GP7
GP6
GP5
GP4
GP3
GP2
GP1
GP0
0000 0000
OLATA
0A
OL7
OL6
OL5
OL4
OL3
OL2
OL1
OL0
0000 0000
IODIRB
10
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
1111 1111
IPOLB
11
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
0000 0000
GPINTENB
12
GPINT7
GPINT6
GPINT5
GPINT4
GPINT3
GPINT2
GPINT1
GPINT0
0000 0000
DEFVALB
13
DEF7
DEF6
DEF5
DEF4
DEF3
DEF2
DEF1
DEF0
0000 0000
INTCONB
14
IOC7
IOC6
IOC5
IOC4
IOC3
IOC2
IOC1
IOC0
0000 0000
IOCON
15
BANK
MIRROR
SEQOP
—
—
ODR
INTPOL
INTCC
0000 0000
GPPUB
16
PU7
PU6
PU5
PU4
PU3
PU2
PU1
PU0
0000 0000
INTFB
17
INT7
INT6
INT5
INT4
INT3
INT2
INT1
INTO
0000 0000
INTCAPB
18
ICP7
ICP6
ICP5
ICP4
ICP3
ICP2
ICP1
ICP0
0000 0000
GPIOB
19
GP7
GP6
GP5
GP4
GP3
GP2
GP1
GP0
0000 0000
OLATB
1A
OL7
OL6
OL5
OL4
OL3
OL2
OL1
OL0
0000 0000
DS22103A-page 16
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
TABLE 1-5:
CONTROL REGISTER SUMMARY (IOCON.BANK = 0)
Address
(hex)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
POR/RST
value
IODIRA
00
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
1111 1111
Register
Name
IODIRB
01
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
1111 1111
IPOLA
02
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
0000 0000
IPOLB
03
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
0000 0000
GPINTENA
04
GPINT7
GPINT6
GPINT5
GPINT4
GPINT3
GPINT2
GPINT1
GPINT0
0000 0000
GPINTENB
05
GPINT7
GPINT6
GPINT5
GPINT4
GPINT3
GPINT2
GPINT1
GPINT0
0000 0000
DEFVALA
06
DEF7
DEF6
DEF5
DEF4
DEF3
DEF2
DEF1
DEF0
0000 0000
DEFVALB
07
DEF7
DEF6
DEF5
DEF4
DEF3
DEF2
DEF1
DEF0
0000 0000
INTCONA
08
IOC7
IOC6
IOC5
IOC4
IOC3
IOC2
IOC1
IOC0
0000 0000
INTCONB
09
IOC7
IOC6
IOC5
IOC4
IOC3
IOC2
IOC1
IOC0
0000 0000
IOCON
0A
BANK
MIRROR
SEQOP
—
—
ODR
INTPOL
INTCC
0000 0000
IOCON
0B
BANK
MIRROR
SEQOP
—
—
ODR
INTPOL
INTCC
0000 0000
GPPUA
0C
PU7
PU6
PU5
PU4
PU3
PU2
PU1
PU0
0000 0000
GPPUB
0D
PU7
PU6
PU5
PU4
PU3
PU2
PU1
PU0
0000 0000
INTFA
0E
INT7
INT6
INT5
INT4
INT3
INT2
INT1
INTO
0000 0000
INTFB
0F
INT7
INT6
INT5
INT4
INT3
INT2
INT1
INTO
0000 0000
INTCAPA
10
ICP7
ICP6
ICP5
ICP4
ICP3
ICP2
ICP1
ICP0
0000 0000
INTCAPB
11
ICP7
ICP6
ICP5
ICP4
ICP3
ICP2
ICP1
ICP0
0000 0000
GPIOA
12
GP7
GP6
GP5
GP4
GP3
GP2
GP1
GP0
0000 0000
GPIOB
13
GP7
GP6
GP5
GP4
GP3
GP2
GP1
GP0
0000 0000
OLATA
14
OL7
OL6
OL5
OL4
OL3
OL2
OL1
OL0
0000 0000
OLATB
15
OL7
OL6
OL5
OL4
OL3
OL2
OL1
OL0
0000 0000
© 2008 Microchip Technology Inc.
DS22103A-page 17
MCP23018/MCP23S18
1.6.1
I/O DIRECTION REGISTER
Controls the direction of the data I/O.
When a bit is set, the corresponding pin becomes an
input. When a bit is clear, the corresponding pin
becomes an output.
REGISTER 1-3:
IODIR – I/O DIRECTION REGISTER
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
IO7:IO0: Controls the direction of data I/O <7:0>
1 = Pin is configured as an input.
0 = Pin is configured as an output.
DS22103A-page 18
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
1.6.2
INPUT POLARITY REGISTER
This register allows the user to configure the polarity on
the corresponding GPIO port bits.
If a bit is set, the corresponding GPIO register bit will
reflect the inverted value on the pin.
REGISTER 1-4:
IPOL – INPUT POLARITY PORT REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
IP7:IP0: Controls the polarity inversion of the input pins <7:0>
1 = GPIO register bit will reflect the opposite logic state of the input pin.
0 = GPIO register bit will reflect the same logic state of the input pin.
© 2008 Microchip Technology Inc.
DS22103A-page 19
MCP23018/MCP23S18
1.6.3
INTERRUPT-ON-CHANGE
CONTROL REGISTER
The GPINTEN register controls the interrupt-onchange feature for each pin.
If a bit is set, the corresponding pin is enabled for
interrupt-on-change. The DEFVAL and INTCON
registers must also be configured if any pins are
enabled for interrupt-on-change.
REGISTER 1-5:
GPINTEN – INTERRUPT-ON-CHANGE PINS
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
GPINT7
GPINT6
GPINT5
GPINT4
GPINT3
GPINT2
GPINT1
GPINT0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
GPINT7:GPINT0: General purpose I/O interrupt-on-change pins <7:0>
1 = Enable GPIO input pin for interrupt-on-change event
0 = Disable GPIO input pin for interrupt-on-change event.
DS22103A-page 20
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
1.6.4
DEFAULT COMPARE REGISTER
FOR INTERRUPT-ON-CHANGE
The default comparison value is configured in the
DEFVAL register. If enabled (via GPINTEN and INTCON) to compare against the DEFVAL register, an
opposite value on the associated pin will cause an
interrupt to occur.
REGISTER 1-6:
DEFVAL – DEFAULT VALUE REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
DEF7
DEF6
DEF5
DEF4
DEF3
DEF2
DEF1
DEF0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
DEF7:DEF0: Sets the compare value for pins configured for interrupt-on-change from defaults <7:0>.
Refer to INTCON.
If the associated pin level is the opposite from the register bit, an interrupt occurs.
Refer to INTCON and GPINTEN.
© 2008 Microchip Technology Inc.
DS22103A-page 21
MCP23018/MCP23S18
1.6.5
INTERRUPT CONTROL REGISTER
The INTCON register controls how the associated pin
value is compared for the interrupt-on-change feature.
If a bit is set, the corresponding I/O pin is compared
against the associated bit in the DEFVAL register. If a
bit value is clear, the corresponding I/O pin is compared
against the previous value.
REGISTER 1-7:
INTCON – INTERRUPT-ON-CHANGE CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IOC7
IOC6
IOC5
IOC4
IOC3
IOC2
IOC1
IOC0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
IOC7:IOC0: Controls how the associated pin value is compared for interrupt-on-change <7:0>.
1 = Pin value is compared against the associated bit is DEFVAL register
0 = Pin value is compared against the previous pin value.
Refer to INTCON and GPINTEN.
DS22103A-page 22
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
1.6.6
CONFIGURATION REGISTER
The IOCON register
configuring the device:
contains
several
bits
for
The BANK bit changes how the registers are mapped
(see Table 1-4 and Table 1-5 for more details).
• If BANK = 1, the registers associated with each
port are segregated. Registers associated with
PORTA are are mapped from address 00h - 0Ah
and registers associated with PORTB are
mapped from Address 10h - 1Ah
• If BANK = 0, the A/B registers are paired. For
example, IODIRA is mapped to address 00h and
IODIRB is mapped to the next address (address
01h). The mapping for all registers is from 00h 15h
It is important to take care when changing the BANK bit
as the address mapping changes after the byte is
clocked into the device. The address pointer may point
to an invalid location after the bit is modified.
For example, if the device is configured to automatically increment its internal address pointer the following
scenario would occur:
• BANK = 0
• Write 80h to 0Ah (IOCON) to set the BANK bit
• After the write completes the internal address now
points to 0Bh which is an invalid address when
the BANK bit is set
For this reason, it is advised to only perform byte writes
to this register when changing the BANK bit.
Note:
The INTB pin is not bonded out on the
MCP23S18 (SPI) device in the 24-lead
QFN package. The MIRROR bit must be
configured to a “1” in order for interrupts to
be detected on PORTB.
The MIRROR bit controls how the INTA and INTB pins
function with respect to each other.
• When MIRROR = 1, the INTn pins are functionally
OR’ed so that an interrupt on either port will cause
both pins to activate
• When MIRROR = 0, the INT pins are separated.
Interrupt conditions on a port will cause its respective INT pin to activate
The Sequential Operation (SEQOP) controls the
incrementing function of the address pointer. If the
address pointer is disabled, the address pointer does
not automatically increment after each byte is clocked
during a serial transfer. This feature is useful when it is
desired to continuously poll (read) or modify (write) a
register.
The Open-Drain (ODR) control bit enables/disables the
INT pin for open-drain configuration.
The Interrupt Polarity (INTPOL) sets the polarity of the
INT pin. This bit is functional only when the ODR bit is
cleared, configuring the INT pin as active push-pull.
The Interrupt Clearing Control (INTCC) configures how
interrupts are cleared. When set (INTCC = 1), the
interrupt is cleared when the INTCAP register is read.
When cleared (INTCC = 0), the interrupt is cleared
when the GPIO register is read.
The interrupt can only be cleared when the interrupt
condition is inactive. Refer to Section 1.7.5 “Clearing
Interrupts” for details.
© 2008 Microchip Technology Inc.
DS22103A-page 23
MCP23018/MCP23S18
REGISTER 1-8:
IOCON – I/O EXPANDER CONFIGURATION REGISTER
R/W-0
BANK
R/W-0
R/W-0
U-0
U-0
R/W-0
R/W-0
R/W-0
MIRROR
SEQOP
-
-
ODR
INTPOL
INTCC
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
BANK: Controls how the registers are addressed (see Figure 1-4 and Figure 1-5)
1 = The registers associated with each port are separated into different banks
0 = The registers are in the same bank (addresses are sequential)
bit 6
MIRROR: INT pins mirror bit
1 = The INT pins are internally connected in a wired OR configuration
0 = The INT pins are not connected. INTA is associated with Port A and INTB is associated with Port B
bit 5
SEQOP: Sequential Operation mode bit.
1 = Sequential operation disabled, address pointer does not increment.
0 = Sequential operation enabled, address pointer increments.
bit 4
Unimplemented: Reads as 0
bit 3
Unimplemented: Reads as 0
bit 2
ODR: Configures the INT pin as an open-drain output.
1 = Open-drain output (overrides the INTPOL bit).
0 = Active driver output (INTPOL bit sets the polarity).
bit 1
INTPOL: Sets the polarity of the INT output pin.
1 = Active-high.
0 = Active-low.
bit 0
INTCC: Interrupt Clearing Control
1 = Reading INTCAP register clears the interrupt
0 = Reading GPIO register clears the interrupt
DS22103A-page 24
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
1.6.7
PULL-UP RESISTOR
CONFIGURATION REGISTER
The GPPU register controls the pull-up resistors for the
port pins. If a bit is set the corresponding port pin is
internally pulled up with an internal resistor.
REGISTER 1-9:
GPPU – GPIO PULL-UP RESISTOR REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PU7
PU6
PU5
PU4
PU3
PU2
PU1
PU0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
PU7:PU0: Controls the internal pull-up resistors on each pin (when configured as an input or output)
<7:0>.
1 = Pull-up enabled.
0 = Pull-up disabled.
FIGURE 1-10:
TYPICAL PERFORMANCE CURVE FOR THE INTERNAL PULL-UP RESISTORS
GPIO Pin Internal Pull-up Current vs VDD
400
350
T = -40°C
IPU (µA)
300
T = +25°C
250
200
150
T = +125°C
100
T = +85°C
50
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VDD (V)
© 2008 Microchip Technology Inc.
DS22103A-page 25
MCP23018/MCP23S18
1.6.8
INTERRUPT FLAG REGISTER
The INTF register reflects the interrupt condition on the
port pins of any pin that is enabled for interrupts via the
GPINTEN register. A ‘set’ bit indicates that the
associated pin caused the interrupt.
This register is ‘read only’. Writes to this register will be
ignored.
REGISTER 1-10:
INTF – INTERRUPT FLAG REGISTER
R-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
INT7
INT6
INT5
INT4
INT3
INT2
INT1
INT0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
INT7:INT0: Reflects the interrupt condition on the port. Will reflect the change only if interrupts are
enabled (GPINTEN) <7:0>.
1 = Pin caused interrupt.
0 = Interrupt not pending.
DS22103A-page 26
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
1.6.9
INTERRUPT CAPTURE REGISTER
The INTCAP register captures the GPIO port value at
the time the interrupt occurred. The register is ‘read
only’ and is updated only when an interrupt occurs. The
register will remain unchanged until the interrupt is
cleared via a read of INTCAP or GPIO.
REGISTER 1-11:
INTCAP – INTERRUPT CAPTURED VALUE FOR PORT REGISTER
R-x
R-x
R-x
R-x
R-x
R-x
R-x
R-x
ICP7
ICP6
ICP5
ICP4
ICP3
ICP2
ICP1
ICP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
ICP7:ICP0: Reflects the logic level on the port pins at the time of interrupt due to pin change <7:0>.
1 = Logic-high.
0 = Logic-low.
© 2008 Microchip Technology Inc.
DS22103A-page 27
MCP23018/MCP23S18
1.6.10
PORT REGISTER
The GPIO register reflects the value on the port.
Reading from this register reads the port. Writing to this
register modifies the Output Latch (OLAT) register.
REGISTER 1-12:
GPIO – GENERAL PURPOSE I/O PORT REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
GP7
GP6
GP5
GP4
GP3
GP2
GP1
GP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
GP7:GP0: Reflects the logic level on the pins <7:0>.
1 = Logic-high.
0 = Logic-low.
DS22103A-page 28
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
1.6.11
OUTPUT LATCH REGISTER (OLAT)
The OLAT register provides access to the output
latches. A read from this register results in a read of the
OLAT and not the port itself. A write to this register
modifies the output latches that modifies the pins
configured as outputs.
REGISTER 1-13:
OLAT – OUTPUT LATCH REGISTER 0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
OL7
OL6
OL5
OL4
OL3
OL2
OL1
OL0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7-0
x = Bit is unknown
OL7:OL0: Reflects the logic level on the output latch <7:0>.
1 = Logic-high.
0 = Logic-low.
© 2008 Microchip Technology Inc.
DS22103A-page 29
MCP23018/MCP23S18
1.7
Interrupt Logic
1.7.2
If enabled, the MCP23X18 activates the INTn interrupt
output when one of the port pins changes state or when
a pin does not match the pre-configured default. Each
pin is individually configurable as follows:
• Enable/disable interrupt via GPINTEN
• Can interrupt on either pin change or change from
default as configured in DEFVAL
Both conditions are referred to as Interrupt on Change
(IOC).
The Interrupt Control (INT) Module uses the following
registers/bits:
• IOCON.MIRROR - controls if the two interrupt
pins mirror each other.
• GPINTEN - Interrupt enable register
• INTCON - Controls the source for the IOC
• DEFVAL - Contains the register default for IOC
operation
1.7.1
INTA AND INTB
There are two interrupt pins, INTA and INTB. By
default, INTA is associated with GPAn pins (Port A) and
INTB is associated with GPBn pins (Port B). Each port
has an independent signal which is cleared if its
associated GPIO or INTCAP register is read.
1.7.1.1
Mirroring the INT pins
Additionally, the INTn pins can be configured to mirror
each other so that any interrupt will cause both pins to
go active. This is controlled via IOCON.MIRROR.
If IOCON.MIRROR = 0, the internal signals are routed
independently to the INTA and INTB pads.
If IOCON.MIRROR = 1, the internal signals are OR’ed
together and routed to the INTn pads. In this case, the
interrupt will only be cleared if the associated GPIO or
INTCAP is read (see Table 1-6).
TABLE 1-6:
INTERRUPT OPERATION
(IOCON.MIRROR = 1)
Interrupt
Condition
Read Port N*
GPIOA
Port A
Clear
Port B
Unchanged
Port A
Unchanged
GPIOB
GPIOA and
GPIOB
Interupt
Result
Port B
Clear
Port A
Unchanged
Port B
Unchanged
Both Port A
and Port B
Clear
IOC FROM PIN CHANGE
If enabled, the MCP23X18 will generate an interrupt if
a mismatch condition exists between the current port
value and the previous port value. Only IOC enabled
pins will be compared. See GPINTEN and INTCON
registers.
1.7.3
IOC FROM REGISTER DEFAULT
If enabled, the MCP23X18 will generate an interrupt if
a mismatch occurs between the DEFVAL register and
the port. Only IOC enabled pins will be compared. See
GPINTEN, INTCON, and DEFVAL registers.
1.7.4
INTERRUPT OPERATION
The INTn interrupt output can be configured as “active
low”, “active high”, or “open drain” via the IOCON
register.
Only those pins that are configured as an input (IODIR
register) with interrupt-on-change (IOC) enabled
(GPINTEN register) can cause an interrupt. Pins
defined as an output have no effect on the interrupt
output pin.
Input change activity on a port input pin that is enabled
for IOC will generate an internal device interrupt and
the device will capture the value of the port and copy it
into INTCAP.
The first interrupt event will cause the port contents to
be copied into the INTCAP register. Subsequent
interrupt conditions on the port will not cause an
interrupt to occur as long as the interrupt is not cleared
by a read of INTCAP or GPIO.
1.7.5
CLEARING INTERRUPTS
The interrupt will remain active until the INTCAP or
GPIO register is read (depending on IOCON.INTCC).
Writing to these registers will not affect the interrupt.
The interrupt condition will be cleared after the LSb of
the data is clocked out during a Read command of
GPIO or INTCAP (depending on IOCON.INTCC).
Note:
Assuming IOCON.INTCC = 0 (INT cleared
on GPIO read): The value in INTCAP can
be lost if GPIO is read before INTCAP
while another IOC is pending. After reading GPIO, the interrupt will clear and then
set due to the pending IOC, causing the
INTCAP register to update.
* Port n = GPIOn or INTCAPn
DS22103A-page 30
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
1.7.6
INTERRUPT CONDITIONS
FIGURE 1-11:
INTERRUPT-ON-PINCHANGE
There are two possible configurations to cause
interrupts (configured via INTCON):
1.
2.
Pins configured for interrupt-on-pin-change
will cause an interrupt to occur if a pin changes
to the opposite state. The default state is reset
after an interrupt occurs. For example, an
interrupt occurs by an input changing from 1 to
0. The new initial state for the pin is a logic 0.
Pins configured for interrupt-on-change from
register value will cause an interrupt to occur if
the corresponding input pin differs from the
register bit. The interrupt condition will remain as
long as the condition exists, regardless if the
INTAP or GPIO is read.
GPx
INT
ACTIVE
Port value
is captured
into INTCAP
ACTIVE
Read GPIO
or INTCAP
FIGURE 1-12:
Port value
is captured
into INTCAP
INTERRUPT-ON-CHANGE
FROM REGISTER
DEFAULT
See Figure 1-11 and Figure 1-12 for more information
on interrupt operations.
DEFVAL
GP:
7
6
5
4
3
2
1
0
X
X
X
X
X
1
X
X
GP2
INT
ACTIVE
Port value
is captured
into INTCAP
© 2008 Microchip Technology Inc.
ACTIVE
Read GPIO
or INTCAP
(INT clears only if interrupt
condition does not exist.)
DS22103A-page 31
MCP23018/MCP23S18
NOTES:
DS22103A-page 32
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
2.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings (†)
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +7.0V
Voltage on RESET with respect to VSS ..................................................................................................... -0.3V to +14V
Voltage on all other pins with respect to VSS (except VDDand GPIOA/B) ...................................... -0.6V to (VDD + 0.6V)
Voltage on GPIO Pins: ................................................................................................................................. -0.6V to 5.5V
Total power dissipation (Note 1)...........................................................................................................................700 mW
Maximum current out of VSS pin ...........................................................................................................................400 mA
Maximum current into VDD pin ..............................................................................................................................125 mA
Input clamp current, IIK (VI < 0 or VI > VDD)...................................................................................................................... ±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD) .............................................................................................................. ±20 mA
Maximum output current sunk by any Output pin....................................................................................................25 mA
Maximum output current sunk by any Output pin (VDD = 1.8V) ..............................................................................10 mA
Maximum output current sourced by any Output pin ..............................................................................................25 mA
Maximum output current sourced by any Output pin (VDD = 1.8V).........................................................................10 mA
Note:
Power dissipation is calculated as follows:
Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
†
NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
© 2008 Microchip Technology Inc.
DS22103A-page 33
MCP23018/MCP23S18
2.1
DC CHARACTERISTICS
DC Characteristics
Param
No.
Characteristic
Operating Conditions (unless otherwise indicated):
1.8V ≤ VDD ≤ 5.5V at -40°C ≤ TA ≤ +125°C
Sym
Min
Typ( 2)
Max
Units
D001
Supply Voltage
VDD
1.8
—
5.5
V
D002
VDD Start Voltage to
Ensure Power-on
Reset
VPOR
—
VSS
—
V
D003
VDD Rise Rate to
Ensure Power-on
Reset
SVDD
0.05
—
—
V/ms
Conditions
Design guidance only.
Not tested.
D004
Supply Current
IDD
—
—
1
mA
SCL/SCK = 1 MHz
D005
Standby (Idle) current
IDDS
—
—
1
µA
–40°C ≤ TA ≤ +85°C
—
—
6
µA
+85°C ≤ TA ≤ +125°C
VIL
VSS
—
0.2 VDD
V
CS, SCL/SCK, SDA,
SI, RESET
VIH
0.8 VDD
—
VDD
V
GPIO
VIH
0.8 VDD
—
5.5
V
IIL
—
—
±1
µA
Input Low-Voltage
D031
CS, GPIO, SCL/SCK,
SDA, SI, RESET
Input High-Voltage
D041
Input Leakage Current
D060
I/O port pins
VSS ≤ VPIN ≤ VDD,
Output Leakage Current
D065
I/O port pins
ILO
—
—
±1
µA
VSS ≤ VPIN ≤ VDD,
D070
GPIO internal pull-up
current
IPU
—
220
—
µA
VDD = 5V, GP Pins = VSS
Note 1
VOL
—
—
0.6
V
IOL = 8.5 mA, VDD = 4.5V
(open-drain)
INT
—
—
0.6
V
IOL = 1.6 mA, VDD = 4.5V
SO, SDA
—
—
0.6
V
IOL = 3.0 mA, VDD = 1.8V
SDA
—
—
0.8
V
IOL = 3.0 mA, VDD = 4.5V
VDD – 0.7
—
—
V
IOH = -3.0 mA, VDD = 4.5V
VDD – 0.7
—
—
Output Low-Voltage
D080
GPIO
Output High-Voltage
D090
INT, SO
VOH
IOH = -400 µA, VDD = 1.8V
Capacitive Loading Specs on Output Pins
D101
GPIO, SO, INT
CIO
—
—
50
pF
D102
SDA
CB
—
—
400
pF
Note 1:
2:
This parameter is characterized, not 100% tested.
Data in the Typical (“Typ”) column is at 5V, +25°C unless otherwise stated.
DS22103A-page 34
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
2.2
AC CHARACTERISTICS
FIGURE 2-1:
LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
VDD
Pin
1 kΩ
SCL and
SDA pin
MCP23018
50 pF
135 pF
RESET AND DEVICE RESET TIMER TIMING
FIGURE 2-2:
VDD
RESET
30
32
31
Internal
RESET
34
Output pin
TABLE 2-1:
RESET AND DEVICE RESET TIMER REQUIREMENTS
AC Characteristics Standard Operating Conditions (unless otherwise specified)
1.8V ≤ VDD ≤ 5.5V at -40°C ≤ TA ≤ +125°C.
Parameter
No.
Sym
Characteristic
30
TRSTL RESET Pulse Width (low)
32
THLD
31
TPOR POR at device power up
34
Note 1:
2:
TioZ
Device active after reset high
Output Hi-impedance from
RESET Low
Min
Typ( 2) Max
Units
Conditions
1
—
—
µs
VDD = 5.0V
—
0
—
µs
VDD = 5.0V
—
20
—
µs
VDD = 5.0V
—
—
1
µs
This parameter is characterized, not 100% tested.
Data in the Typical (“Typ”) column is at 5V, +25°C, unless otherwise stated.
© 2008 Microchip Technology Inc.
DS22103A-page 35
MCP23018/MCP23S18
TABLE 2-2:
GP AND INT PINS
AC Characteristics Standard Operating Conditions (unless otherwise specified)
1.8V ≤ VDD ≤ 5.5V at -40°C ≤ TA ≤ +125°C.
Parameter
No.
Sym
Characteristic
50
tGPOV Serial data to output valid
51
tINTD
52
tGPIV
Typ( 2) Max
Min
Units
—
—
500
ns
Interrupt pin disable time
—
—
600
ns
GP input change to register valid
—
450
—
ns
53
tGPINT IOC event to INT active
—
—
600
ns
54
tGLITCH Glitch filter on GP pins
—
—
50
ns
Note 1:
2:
Conditions
Note 1
Note 1
This parameter is characterized, not 100% tested.
Data in the Typical (“Typ”) column is at 5V, 25°C, unless otherwise stated.
FIGURE 2-3:
GPIO AND INT TIMING
SCL
SDA
In
D1
D0
LSb of data byte zero
during a write or read
command, depending
50
on parameter
GPn
Output
Pin
51
INT
Pin
INT pin active
GPn
Input
Pin
INT pin
inactive
53
52
Register
Loaded
DS22103A-page 36
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
TABLE 2-3:
HARDWARE ADDRESS LATCH TIMING
AC Characteristics
Parameter
No.
Sym
40
tADEN
41
Characteristic
Time from VDD stable after
POR to ADC enable
tADDRLAT Time from ADC enable to
address decode and latch
42
Note 1:
2:
Standard Operating Conditions (unless otherwise specified)
1.8V ≤ VDD ≤ 5.5V at -40°C ≤ TA ≤ +125°C.
tADDIS
Time from raising edge of serial
clock to ADC disable
Min
Typ( 2) Max
Units
Conditions
—
0
—
µs
Note 1
—
50
—
ns
Note 1
—
10
—
ns
Note 1
This parameter is characterized, not 100% tested.
Data in the Typical (“Typ”) column is at 5V, +25°C, unless otherwise stated..
FIGURE 2-4:
HARDWARE ADDRESS LATCH TIMING
40
VDD
41
adc_en
i2c_addr[2:0]
42
SCL
© 2008 Microchip Technology Inc.
DS22103A-page 37
MCP23018/MCP23S18
FIGURE 2-5:
I2C BUS START/STOP BITS TIMING
SCL
93
91
90
92
SDA
STOP
Condition
START
Condition
Note 1: Refer to Figure 2-1 for load conditions.
FIGURE 2-6:
I2C BUS DATA TIMING
103
102
100
101
SCL
90
106
91
107
92
SDA
In
109
109
110
SDA
Out
Note 1: Refer to Figure 2-1 for load conditions.
DS22103A-page 38
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
TABLE 2-4:
I2C BUS DATA REQUIREMENTS (SLAVE MODE)
I2C™ AC Characteristics
Param
No.
100
Characteristic
Operating Conditions (unless otherwise indicated):
1.8V ≤ VDD ≤ 5.5V at -40°C ≤ TA ≤ +125°C
RPU (SCL, SDA) = 1 kΩ, CL (SCL, SDA) = 135 pF.
Min
Typ
Max
Units
4.0
—
—
µs
1.8V – 5.5V
400 kHz mode
0.6
—
—
µs
1.8V – 5.5V
3.4 MHz mode
0.06
—
—
µs
2.7V – 5.5V
100 kHz mode
4.7
—
—
µs
1.8V – 5.5V
400 kHz mode
1.3
—
—
µs
1.8V – 5.5V
3.4 MHz mode
0.16
—
—
µs
2.7V – 5.5V
—
—
1000
ns
1.8V – 5.5V
—
300
ns
1.8V – 5.5V
—
80
ns
2.7V – 5.5V
—
300
ns
1.8V – 5.5V
Clock High Time:
Sym
THIGH
100 kHz mode
101
102
Clock Low Time:
SDA and SCL Rise Time:
100 kHz mode
TLOW
TR
(Note 1)
400 kHz mode
20 + 0.1
3.4 MHz mode
103
SDA and SCL Fall Time:
100 kHz mode
90
91
92
Note 1:
2:
3:
—
CB(2)
400 kHz mode
20 + 0.1
—
300
ns
1.8V – 5.5V
3.4 MHz mode
10
—
80
ns
2.7V – 5.5V
100 kHz mode
4.7
—
—
µs
1.8V – 5.5V
400 kHz mode
0.6
—
—
µs
1.8V – 5.5V
3.4 MHz mode
0.16
—
—
µs
2.7V – 5.5V
100 kHz mode
4.0
—
—
µs
1.8V – 5.5V
400 kHz mode
0.6
—
—
µs
1.8V – 5.5V
0.16
—
—
µs
2.7V – 5.5V
0
—
3.45
µs
1.8V – 5.5V
START Condition Setup Time:
START Condition Hold Time:
TSU:STA
THD:STA
Data Input Hold Time:
THD:DAT
100 kHz mode
107
CB(2)
10
TF
(Note 1)
3.4 MHz mode
106
Conditions
400 kHz mode
0
—
0.9
µs
1.8V – 5.5V
3.4 MHz mode
0
—
0.07
µs
2.7V – 5.5V
Data Input Setup Time:
TSU:DAT
100 kHz mode
250
—
—
ns
1.8V – 5.5V
400 kHz mode
100
—
—
ns
1.8V – 5.5V
3.4 MHz mode
0.01
—
—
µs
2.7V – 5.5V
100 kHz mode
4.0
—
—
µs
1.8V – 5.5V
400 kHz mode
0.6
—
—
µs
2.7V – 5.5V
3.4 MHz mode
0.16
—
—
µs
4.5V – 5.5V
STOP Condition Setup Time:
TSU:STO
This parameter is characterized, not 100% tested.
CB is specified from 10 to 400 (pF).
This parameter is not applicable in high-speed mode (3.4 MHz).
© 2008 Microchip Technology Inc.
DS22103A-page 39
MCP23018/MCP23S18
I2C BUS DATA REQUIREMENTS (SLAVE MODE) (CONTINUED)
TABLE 2-4:
Operating Conditions (unless otherwise indicated):
1.8V ≤ VDD ≤ 5.5V at -40°C ≤ TA ≤ +125°C
RPU (SCL, SDA) = 1 kΩ, CL (SCL, SDA) = 135 pF.
I2C™ AC Characteristics
Param
No.
Characteristic
109
Min
Typ
Max
Units
100 kHz mode
—
—
3.45
µs
400 kHz mode
—
—
0.9
µs
1.8V – 5.5V
3.4 MHz mode
—
—
0.18
µs
2.7V – 5.5V
4.7
—
—
µs
1.8V – 5.5V
1.3
—
—
µs
1.8V – 5.5V
N/A
—
N/A
µs
2.7V – 5.5V
—
—
400
pF
(Note 1)
—
—
100
pF
(Note 1)
Output Valid From Clock:
110
Bus Free Time:
Sym
TAA
TBUF
(NOTE 3)
100 kHz mode
400 kHz mode
3.4 MHz mode
Bus Capacitive Loading:
100 kHz and 400 kHz
Note 1:
2:
3:
1.8V – 5.5V
CB
(NOTE 2)
3.4 MHz
Input Filter Spike
Suppression: (SDA and SCL)
Conditions
TSP
100 kHz and 400 kHz
—
—
50
ns
(Note 1)
3.4 MHz
—
—
10
ns
(Note 1)
This parameter is characterized, not 100% tested.
CB is specified from 10 to 400 (pF).
This parameter is not applicable in high-speed mode (3.4 MHz).
FIGURE 2-7:
SPI INPUT TIMING
3
CS
11
6
1
Mode 1,1
10
7
2
SCK Mode 0,0
4
5
SI
MSB in
SO
DS22103A-page 40
LSB in
high impedance
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
FIGURE 2-8:
SPI OUTPUT TIMING
CS
8
2
9
SCK
Mode 1,1
Mode 0,0
12
13
SO
MSB out
SI
© 2008 Microchip Technology Inc.
14
LSB out
don’t care
DS22103A-page 41
MCP23018/MCP23S18
TABLE 2-5:
SPI INTERFACE AC CHARACTERISTICS
SPI Interface AC Characteristics
Param
No.
Characteristic
Operating Conditions (unless otherwise indicated):
1.8V ≤ VDD ≤ 5.5V at -40°C ≤ TA ≤ +125°C.
Sym
Min
Typ
Max
Units
Clock Frequency
FCLK
—
—
10
MHz
1
CS Setup Time
TCSS
50
—
—
ns
2
CS Hold Time
TCSH
50
—
—
ns
1.8V – 5.5V
3
CS Disable Time
TCSD
50
—
—
ns
1.8V – 5.5V
4
Data Setup Time
TSU
10
—
—
ns
1.8V – 5.5V
5
Data Hold Time
THD
10
—
—
ns
1.8V – 5.5V
6
CLK Rise Time
TR
—
—
2
µs
Note 1
7
CLK Fall Time
TF
—
—
2
µs
Note 1
8
Clock High Time
THI
45
—
—
ns
1.8V – 5.5V
9
Clock Low Time
TLO
45
—
—
ns
1.8V – 5.5V
10
Clock Delay Time
TCLD
50
—
—
ns
11
Clock Enable Time
TCLE
50
—
—
ns
12
Output Valid from Clock
Low
TV
—
—
45
ns
13
Output Hold Time
THO
0
—
—
ns
14
Output Disable Time
TDIS
—
—
100
ns
Note 1:
Conditions
1.8V – 5.5V
1.8V – 5.5V
This parameter is characterized, not 100% tested.
FIGURE 2-9:
TYPICAL PERFORMANCE CURVE FOR SPI TV SPECIFICATION (PARAM #12)
TV (ns)
TV vs VDD
40
35
30
25
20
15
10
5
0
T = +125°C
T = +85°C
T = -40°C
T = +25°C
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VDD (V)
DS22103A-page 42
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
3.0
PACKAGING INFORMATION
3.1
Package Marking Information
24-Lead QFN
Example
XXXXX
XXXXXX
XXXXXX
YWWNNN
23018
e3
E/MJ^^
0838
256
24-Lead SSOP (MCP23018 only)
XXXXXXXXXXXX
XXXXXXXXXXXX
YYWWNNN
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
Example:
MCP23018
e3
E/SS^^
0838256
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
© 2008 Microchip Technology Inc.
DS22103A-page 43
MCP23018/MCP23S18
Package Marking Information (Continued)
28-Lead SPDIP (300 mil)
Example:
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
YYWWNNN
28-Lead SOIC (300 mil)
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
YYWWNNN
DS22103A-page 44
MCP23018
e3
E/SP^^
0838256
Example:
MCP23018
E/SO^^
e3
YYWW
NNN
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
24-Lead Plastic Quad Flat, No Lead Package (MJ) – 4x4x0.9 mm Body [QFN]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2008 Microchip Technology Inc.
DS22103A-page 45
MCP23018/MCP23S18
!
"#$ %
&"
'#
())$$$
)
"
DS22103A-page 46
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
!"#$%
!
"#$ %
&"
'#
())$$$
)
"
D
N
E
E1
1 2
NOTE 1
b
e
c
φ
A2
A
A1
L
L1
5
6
7!/'&
6600*
7
7
78
9
&
8-;
<
:,34
<
##&""
+:,
+,
+,
#''
+
,
<
<
8-=#
0
##&"=#
0+
,
,1
,:
8-6
,
6
6
,,
,
,
6+
+,*0
6#"
<
I
>
>
,
>
6#=#
/
<
1
+ &+- !#.'!-%/!! /#$#
#0+#!##' ! #' ! .#
#
1 #
02+,
34( 3 .-! $$! *0( *' %! !$!%''
!
$ 4+13
© 2008 Microchip Technology Inc.
DS22103A-page 47
MCP23018/MCP23S18
&
#'(
!!"#$'(%
!
"#$ %
&"
'#
())$$$
)
"
N
NOTE 1
E1
1
2 3
D
E
A2
A
L
c
b1
A1
b
e
eB
5
6
7!/'&
74;0
7
7
78
9
&
&
<
<
##&""
+
+1,
+,
3 &
+
+,
<
<
!#!#=#
0
1+
11,
##&"=#
0+
,
,
8-6
+1,
+1:,
+
&
6
++
+1
+,
6#"
+
+,
/+
,
/
+
+
3
<
<
5
6#=#
6$6#=#
8-*$
?
+34
1
+ &+- !#.'!-%/!! /#$#
?'4 1 #0+#!##' ! #' ! .#+@
#
#
02+,
34( 3 .-! $$! $ 43
DS22103A-page 48
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
&
)*+!"#$(,%
!
"#$ %
&"
'#
())$$$
)
"
D
N
E
E1
NOTE 1
1 2 3
e
b
h
α
A2
A
h
c
φ
L
A1
5
6
7!/'&
β
L1
6600*
7
7
78
9
&
8-;
<
+34
<
##&""
,
<
<
#''?
+
+
<
1
8-=#
0
##&"=#
0+
,34
8-6
+34
:,
+134
4'A
B
,
<
,
6
6
<
+
6+
+*0
I
>
<
>
6#"
+
<
11
6#=#
/
1+
<
,+
#'
D
,>
<
+,>
#'3
E
,>
<
+,>
+ &+- !#.'!-%/!! /#$#
?'4 1 #0+#!##' ! #' ! .#+,
#
#
02+,
34( 3 .-! $$! *0( *' %! !$!%''
!
$ 4,3
© 2008 Microchip Technology Inc.
DS22103A-page 49
MCP23018/MCP23S18
NOTES:
DS22103A-page 50
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
APPENDIX A:
REVISION HISTORY
Revision A (September 2008)
• Original Release of this Document.
© 2008 Microchip Technology Inc.
DS22103A-page 51
MCP23018/MCP23S18
NOTES:
DS22103A-page 52
© 2008 Microchip Technology Inc.
MCP23018/MCP23S18
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
Device
–
X
/XX
Temperature
Range
Package
MCP23018:
MCP23018T:
MCP23S18:
MCP23S18T:
Examples:
a)
b)
16-Bit I/O Expander w/ I2C™ Interface
16-Bit I/O Expander w/ I2C Interface
(Tape and Reel)
16-Bit I/O Expander w/ SPI Interface
16-Bit I/O Expander w/ SPI Interface
(Tape and Reel)
Temperature
Range
E
= -40°C to +125°C (Extended) *
Package
MJ
= Plastic Quad Flat, No Lead Package
(4x4x0.9 mm Body), 24-Lead
= Skinny Plastic DIP (300 mil Body), 28-Lead
= Plastic SOIC (300 mil Body), 28-Lead
= SSOP, (209 mil Body, 5.30 mm), 24-Lead
c)
d)
e)
f)
a)
SP
SO
SS
b)
c)
d)
© 2008 Microchip Technology Inc.
MCP23018-E/SP:
Extended Temp.,
28LD SPDIP package.
MCP23018-E/SO: Extended Temp.,
28LD SOIC package.
MCP23018T-E/SO: Tape and Reel,
Extended Temp.,
28LD SOIC package.
MCP23018-E/SS: Extended Temp.,
24LD SSOP package.
MCP23018T-E/SS: Tape and Reel,
Extended Temp.,
24LD SSOP package.
MCP23018-E/MJ: Extended Temp.,
24LD QFN package.
MCP23S18-E/SP:
Extended Temp.,
28LD SPDIP package.
MCP23S18-E/SO: Extended Temp.,
28LD SOIC package.
MCP23S18T-E/SO: Tape and Reel,
Extended Temp.,
28LD SOIC package.
MCP23S18T-E/MJ: Tape and Reel,
Extended Temp.,
24LD QFN package.
DS22103A-page 53
MCP23018/MCP23S18
NOTES:
DS22103A-page 54
© 2008 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, rfPIC, SmartShunt and UNI/O are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
FilterLab, Linear Active Thermistor, MXDEV, MXLAB,
SEEVAL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, In-Circuit Serial
Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM,
PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo,
PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total
Endurance, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2008, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2008 Microchip Technology Inc.
DS22103A-page 55
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
01/02/08
DS22103A-page 56
© 2008 Microchip Technology Inc.