8WA1 Screw Terminals 9 9/2 Introduction 9/3 General data on 8WA 9/9 8WA through-type terminals1) 9/15 8WA N-conductor isolating and branch terminals 9/17 8WA Insta or three-tier terminals 9/19 8WA two-tier terminals 9/21 8WA two-tier terminals with electronic components 9/23 8WA diode and isolating terminals 9/24 8WA terminals for components 9/25 8WA fuse terminals 9/26 8WA through-type terminals with soldered and plug-in connection 9/27 8WA measuring transformer terminals 9/32 8WA transformer terminals 1) Also available as a PE version More technical product information: Service&Support Portal: www.support.automation.siemens.com. Product List: Technical specifications Entry List: Updates / Downloads / FAQ / Manuals / Operating instructions / Characteristic curves / Certificates 9 8WA1 Screw Terminals Introduction ■ Overview 9 9/2 Devices Page Function 8WA through-type terminals 9/9 Connection of incoming and outgoing conductors up to 70 mm2 8WA N-conductor isolating and branch terminals 9/15 N-conductor isolating terminals connected to N-busbar 6 mm x 6 mm 8WA Insta or three-tier terminals 9/17 These terminals have up to three terminal functions in a single enclosure and may also have an N-isolating terminal connection to an N-busbar 6 mm × 6 mm. They are optimized for distribution board applications in installation technology 8WA two-tier terminals 9/19 Compact design of the terminal blocks, in which two connecting wires can be installed 8WA two-tier terminals with electronic components 9/21 Terminal blocks with integrated diodes 8WA diode and isolating terminals 9/23 Terminal blocks with integrated diodes or isolation for testing purposes 8WA terminals for components 9/24 Terminals that enable installation of components in the circuit 8WA fuse terminals 9/25 Terminals which can be used to protect control circuits, for example 8WA through-type terminals with soldered and plug-in connection 9/26 Terminals with connection for soldered or plug-in connection 8WA measuring transformer terminals 9/27 Measuring transformer terminals can be used for testing and isolating circuits in switchboards, control rooms, etc. without interrupting operation 8WA transformer terminals 9/32 Optimized terminals for transformers and rectifiers 8WA1 Screw Terminals General data on 8WA ■ Overview Clamping methods The terminals are designed so that when the terminal screws are tightened, any tensile stress which occurs causes elastic deformation of the terminal bodies. This compensates for any creepage of the clamping conductor. Deformation of the thread part prevents loosening of the clamping screw, even in the event of heavy mechanical and thermal strain (e. g. vibration stress of 10 g or thermal cycles). The following clamping methods are used: terminal body with pressure plate for terminal sizes 16, 35 and 70 mm². Strain-relief clamps for terminal sizes 2.5, 4 and 6 mm². Screw with connection disk for fuse terminals and component terminals. Terminal size The terminal size corresponds to the nominal cross-section. According to EN 60947-7-1, a finely stranded copper conductor of nominal cross-section can be connected to any clamping point with or without end sleeve. Terminal strips with different terminal blocks: 8WA1 011-1DG11 terminal blocks, 8WA1 011-1NG31 N-conductor isolating terminals with feeder terminal for N-busbar 6 × 6 mm, 8WA1 011-1PG00 PE terminals, 8WA1 011-1SF12 fuse terminals, and various two-tier terminals. The EN 50022-35-compliant standard mounting rail serves as the PE bar. Terminal blocks are used for the space-saving connection of incoming and outgoing cables in switchboards and distribution boards. Standards Mounting The terminals are snapped onto 35 mm support rails according to IEC 60715 TH35 and secured against movement using end retainers. A lateral mounting tolerance of 0.2 mm must be maintained between the terminals. Conductor connection EN 60664-1, EN 60999 and IEC 60 947-7-1 or IEC 60 947-7-2. Except for flat and bolt-type versions, all terminal bodies are designed so that solid, stranded and finely stranded conductors with or without end sleeves (according to DIN 46228) can be securely clamped (please observe cross-section). The terminals are finger-safe acc. to IEC 60529 and DIN EN 50274 (except for bare terminals and solder connections). Through-type terminals are resistant to earthquakes according to IEC 60068-2-6. Damage to the clamped conductors is prevented by pressure plates or strain-relief clamps. For the conductor cross-sections when 1 or 2 conductors are connected, see technical specifications. Rated short-time withstand current Our screw terminals are able to withstand a rated short-time current corresponding to a current density of 120 A/mm2 specific to the nominal cross-section for a duration of one second. Colored terminal blocks With colored wiring according to EN 60204-1, the connecting level can also be included in the colored markings: • Red for control circuits with AC current • Blue for control circuits with DC current or neutral conductor • Orange for interlock circuits with AC or DC current which are fed from outside and are live when the main switch is turned off • Green-yellow through-type terminals for protective conductors (without connection to the support rail). Design The terminal blocks are insulated at both ends, with the exception of two-tier, flat and bolt-type terminals, which are insulated on one side only. The insulating material for terminal sizes up to 70 mm² is made of thermoplast, polyamide 6.6. The materials used are environment-friendly: For example, they are cadmium-free and contain no halogens or silicone. The plastics used are flame-retardant and self-extinguishing according to EN 60695-2-2, VDE 0471, Part 2-2 and UL 94 V-2. 9/3 9 8WA1 Screw Terminals General data on 8WA Connection of aluminum conductors Accessories Siemens screw terminals are suitable for connecting aluminum conductors provided there is compliance with the normal processing guidelines, i.e. the brushing and greasing of the conductors before connection. Parallel connection bars After a few days, the connection should be tightened again for safety reasons. 5 1 3 1 Screwdriver guide 2 Cut-out for labeling plate 3 Cable entry 4 4 Terminal body 6 5 Thread for parallel connection bar 6 Elastic retaining feet 2 I201_14019 8WA1 through-type terminal with screw terminal at both ends, sectional view PE and PEN terminals 9 In switchgear and controlgear systems the support rails for the terminal blocks are frequently used as protective ground busbars. The PE terminals establish the connection to the support rail. The connection bars are screwed into the terminals from above and allow parallel connection of up to 10 terminals up to terminal size 35 mm². The 10-pole connection bars can be shortened as required. On 70 mm² terminals the connection bars are two-pole. Barriers Barriers are yellow in color and project beyond the contours of the terminals. They serve the visual separation of groups of terminals, the electrical isolation of adjacent connection bars and the improvement of the rated insulation voltage for soldered and plug-in connections. Insulation plates 8WA1 825 and 8WA1 822-7TK00 insulation plates can be used with different terminals for providing electrical insulation between connection bars. Test sockets and plugs The 8WA1 854 test sockets for 2.3 test plugs and reduction plugs with a Ø 4 mm hole can be screwed into some terminals in place of the connection bars. Disconnecting links The 8WA1 865 disconnecting links provide a detachable connection between two adjacent terminals sizes 2.5 to 6 mm². Covers with lightning symbol The fact that there is no separate PE busbar means the PE terminals, the insulated main conductor terminals and N-conductor isolating terminals can be arranged according to user requirements. This makes the individual circuits clearly manageable. The purpose of these covers is to identify the power input terminals. At the same time, they provide additional touch protection. The bare 8WA1 010-1PH01 PE terminals are primarily used for connecting the shields of shielded cables. They are normally mounted on a standard mounting rail, which is supported by an 8WA1 857 insulation carrier and which is equipped with only one PE terminal for connection to the PE conductor. End retainers are available in thermoplastic or galvanized and chromated steel. The end labeling plate can be fitted in an 8WA1 808 end retainer or, in any of three positions, in an 8WA1 805 end retainer. 9/4 End retainers and end labeling plates 8WA1 Screw Terminals General data on 8WA ■ Technical specifications Continuous load at increased ambient temperatures Standard mounting rails as PEN rails The 8WA1 terminal blocks can withstand an uninterrupted current at ambient temperatures of up to +55 °C. At higher ambient temperatures, a current reduction according to the following formula is required: Only use Cu busbars. They must have the same current carrying capacity as protective conductor busbars. PEN busbars must carry only terminals and no devices. Ith2’ = Ith2 · k Ith2 = Uninterrupted current according to selection tables, relative to the nominal cross-section Ith2’ = Uninterrupted current at increased ambient temperature k = Derating factor according to table Ambient temperature Derating factor k 60 °C 0.94 65 °C 0.88 70 °C 0.82 75 °C 0.75 80 °C 0.67 85 °C 0.58 90 °C 0.47 95 °C 0.33 Standard mounting rails as protective conductor busbars Protective conductors with a larger cross-section than the protective conductor busbar, and with the same conductivity, can be connected to standard mounting rails that are also protective conductor busbars and carry current only under fault conditions. Standard mounting rail acc. to EN 50022-35 and IEC 60715 TH35 Material Type 35 × 7.5 Steel 5ST1 141 16 Steel, perforated 5ST1 145 16 Steel 5ST1 142 35 Steel -- Copper 8WA7 551 Similar to 35 × 15 The highest permissible clamping point overtemperature of 45 K specified in IEC 60947-7-1 is not exceeded at an ambient temperature of up to 100 °C. 1) Max. permissible cross-section of connected protective conductor mm² 50 150 1) With 8WA1 010-1PQ00 terminal connection of up to 95 mm² finely stranded or 120 mm² stranded. Clamping points Type 1) Thread diameter of terminal screws Screwdriver blades acc. to DIN 5264 Form B 1.5 8WA1 011- . SF . ., 8WA1 011-1EE00 M3.5 0.8 × 4 2.5 8WA1 . . 1, 8WA1 011-1BF11, 8WA1 011-1EF . . 8WA1 011- . . F . . M2.5 and M3 4 8WA1 011- . . G . . 8WA2 867 6 Terminal size Tightening torque = test torque acc. to DIN VDE 0609 and DIN VDE 0611 Tensile forces acc. to IEC 60947-1 at max. conductor connection Stripped length Nm N 40 mm 0.8 0.5 × 3 0.5 50 11 M2.5 0.8 × 4 0.5 50 11 M3 M3.5 0.8 × 4 0.5 0.8 ... 1 60 11 8WA1 . . 2, 8WA1 011- . . H . . M3.5 0.8 × 4 0.8 80 11 16 8WA1 . . 4, 8WA1 011- . . K . . M4 0.8 × 4 1.2 100 13 25 8WA2 868 M5 1.2 × 6.5 2 135 35 8WA1 . . 5, 8WA1 011- . . M . . 8WA2 870 M6 1.2 × 6.5 2.5 190 17 50 8WH1 000-0AN00, 8WH1 000-0AN01, 8WH1 000-0CN07 M6 1.2 × 8 6 ... 8 -- 24 10 2.5 ... 3 8WH1 070-0AN00 M6 -- 3 ... 7 -- 6 ... 25 70 8WA1 . . 6 M8 4 hexagon socket-head 6 285 25 95 8WA1 010-1PQ00 8WH1 000-0AQ00, 8WH1 000-0AQ01 8WH1 000-0CQ07 8WH1 070-0AQ00 8WH1 060-0AQ00 M8 M8 6 hexagon socket-head 6 hexagon socket-head 15 ... 20 15 ... 20 -- 30 33 M8 M8 M8 6 hexagon socket-head --- 15 ... 20 6 ... 15 25 ... 30 ---- 30 16... 25 29 150 8WH1 000-0AS0. 8WH1 070-0AS00 8WH1 060-0AS00 M10 M10 M10 8 hexagon socket-head --- 25 ... 30 10 ... 18 25 ... 30 ---- 40 10 ... 18 34 240 8WH1 000-0AU0. 8WH1 060-0AU00 M10 M10 10 hexagon socket-head -- 30 ... 35 30 ... 35 --- 40 34 1) Tightening torque also applicable for accessories (socket, connection bars, etc.). 9/5 9 8WA1 Screw Terminals General data on 8WA Rated impulse withstand voltage of terminal blocks Terminal blocks are tested acc. to overvoltage category III. Values dependent on the mains rated voltage rated insulation voltage of terminal block; excerpt from EN 60947-1, table H.1. Rated mains voltage ( rated insulating voltage of the device) Maximum rated operating voltage to ground Preferred values for rated impulse withstand voltage as 1.2/50 s pulse RMS value V AC RMS value V AC or V DC I kV Overvoltage category II kV III kV IV kV -- 50 330 500 800 1500 66/115 100 500 800 1500 2500 120/208 127/220 150 800 1500 2500 4000 230/400 277/480 300 1500 2500 4000 6000 600 2500 4000 6000 8000 1000 4000 6000 8000 12000 400/690 1000 Connection Terminal size Type mm² Smallest conductor cross-section Largest conductor cross-section Solid Stranded Finely Finely stranded with Solid stranded end sleeve 1) Stranded Finely Finely stranded with stranded end sleeve 1) mm² mm² mm² mm² Size mm² mm² mm² mm² Size 1 -- -- 0.75 0.75 ... 10 2.5 -- -- 1.5 1.5 ... 10 0.25 2) 0.25 2) 0.25 2) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 ... 10 0.5 ... 10 0.5 ... 10 4 4 4 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 ... 12 4) 2.5 ... 7 1.5 ... 10 0.5 1 0.5 0.75 0.5 1.5 1.5 1.5 1.5 1.5 1.5 2.5 1.5 1.5 0.5 1.5 1.5 2.5 0.75 0.75 0.75 0.5 0.5 1 0.75 ... 10 0.75 ... 10 0.75 ... 10 0.5 ... 10 0.5 ... 10 1 ... 10 3) 6 6 6 10 10 16 4 4 4 6 6 25 4 4 4 6 6 16 4 4 4 6 6 16 4 4 ... 12 4) 4 ... 12 4) 6 ... 12 6 ... 15 16 ... 12 1.5 1.5 1.5 -4 2.5 2.5 2.5 -10 4 4 4 4 6 1.5 1.5 2.5 4 6 1 ... 10 3) 1.5 ... 7 6) 2.5 ... 12 -6 ... 15 16 16 16 -16 5) 25 25 16 -50 16 16 10 25 35 16 16 10 25 35 16 ... 12 16 ... 15 10 ... 12 -35 ... 18 7) 4 6 6 -----10 -------- 10 10 10 -----16 50 ------- 10 16 16 10 10 25 61) 25 16 50 35 35 35 -35 50 6 6 6 10 10 25 -25 16 -35 35 35 161) 35 50 6 ... 15 6 ... 15 6 ... 15 -----16 ... 12 6) -------- 16 5) 16 16 -----95 -------- 50 35 35 -----95 95 ------- 35 25 25 50 50 50 -50 95 95 95 95 35 -95 150 25 25 25 50 50 50 351) 50 --95 95 95 351) 95 150 25 ... 15 25 ... 15 25 ... 15 -------------- ---- ---- 50 -70 50 -70 ---- ---- -240 -- 150 240 185 150 -185 ---- Single-conductor connection 1.5 2.5 9 4 6 16 25 35 50 70 95 150 240 8WA1 011-.SF . . , 8WA1 011-1EE00 8WA1 211, 8WA1 011-. .F. . 8WA1 011-3JF . . 8WA1 501, 8WA1 511, 8WA1 011-1EF. . 8WA9 200 8WA2 86. feeder terminal 8WA1 011-. .G.. 8WA1 011-1.H.. 8WA1 010-1PH01 8WA1 204, 8WA1 304, 8WA1 011-1BK11 8WA1 604, 8WA1 011-1NK02 8WA1 011-1PK00 8WA2 86. feeder terminal 8WH1 060-0AL00 8WA1 205, 8WA1 305, 8WA1 011-1BM11 8WA1 011-1PM00 8JH4 114 feeder terminal 8WA2 870 8WH1 000-0AN00 8WH1 000-0AN01 8WH1 000-0CN07 8WH1 070-0AN00 8WH1 060-0AN00 8WA1 206 8WA1 010-1PQ00 8WH1 000-0AQ00 8WH1 000-0AQ01 8WH1 000-0CQ07 8WH1 070-0AQ00 8WH1 060-0AQ00 8WH1 000-0AS00, 8WH1 000-0AS01 8WH1 060-0AS00 8WA1 011-1DU.. 8WH1 000-0AU00, 8WH1 000-0AU01 8WH1 060-0AU00 1) End sleeves acc. to DIN 46 228 Sheet 1 without insulation. Size corresponds to sleeve nominal size. 2) 0.12/0.25 mm² corresponds to 0.4/0.6 mm. For 0.75 mm² conductors, use end sleeves 1-10 and press on with insert E1 or PZ 1.5. 3) 4) At voltages > 500 V, shorten end sleeves with inserted conductor to 10 mm before pressing on. 5) Tested up to 16 mm². Fit and press on two end sleeves one after the other (up to stop). 6) 9/6 7) Voltage reduction to 630 V required. 8WA1 Screw Terminals General data on 8WA Terminal size Type Smallest conductor cross-section mm² Largest conductor cross-section Solid Stranded Finely Finely stranded with Solid stranded end sleeve 1) Stranded Finely Finely stranded with stranded end sleeve 1) mm² mm² mm² mm² mm² mm² Size -- 1.5 ... 10 mm² mm² Size Two-wire connection, 2 conductors each of same cross-section; with end sleeves the two rectangular sleeves must be inserted in the same position. 1.5 8WA1 011-. SF . ., -1EE00 2×1 -- -- 2 × 0.75 1 ... 10 3) 2 × 2.5 -- 2 × 1.5 2.5 8WA1 211, 8WA1 011-. .F. . 2 × 0.12 2) 2 × 0.5 2 × 0.5 2 × 0.5 9) 0.75 ... 6 2 × 0.75 2 × 0.5 2 × 0.5 2 × 1.5 9) 1.5 ... 10 8WA1 501, 8WA1 511, 8WA1 011-1EF. . 2 × 0.12 2) 2 × 0.5 2 × 0.25 -- -- 2 × 0.75 2 × 0.5 2 × 0.75 -- -- 4 8WA1 011-. .G. ., -1DG11 8WA1 011-2DG11 8WA1 011-6DG11, top 8WA1 011-6DG11, bottom 8WA1 011-1PG00 8WA1 011-1PG11, -1NG01 2 × 0.5 2 × 0.5 2 × 0.5 2 × 0.5 2 × 0.5 2 × 0.5 2×1 2×1 2×1 2×1 2×1 2×1 2×1 2×1 2×1 2×1 2×1 2×1 2 × 0.5 2 × 0.5 2 × 0.5 2 × 0.5 2 × 0.5 2 × 0.5 0.5 × 10 0.5 × 10 0.5 × 10 0.5 × 10 0.5 × 10 0.5 × 10 2 × 1.5 2×1 2 × 1.5 2×1 2×1 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2×1 2×1 2×1 2×1 2×1 1.5 ... 10 1 ... 10 1 ... 10 1 ... 10 1 ... 10 1 ... 10 6 8WA1 011-1 . H . ., -3DH21 8WA1 010-1PH01 2 × 0.5 2 × 0.5 2 × 0.75 2 × 0.75 2 × 0.75 2 × 0.75 2 × 0.5 2 × 0.5 0.5 × 10 0.5 × 10 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 2 × 1.5 1.5 ... 10 2 × 0.75 1 ... 10 8WA1 204, 8WA1 304, 8WA1 604, 2 × 1 8WA1 011-1BK11 8WA1 734 2 × 2.5 2 × 2.5 2 × 2.5 2×1 1 ... 10 2×4 2×4 2×4 2×4 4 ... 12 -- -- 2 × 1.5 1.5 ... 7 2×4 2×4 2×4 2×4 4 ... 12 35 8WA1 205, 8WA1 305, 8WA1 011-1BM11, 8WA1 735 2×4 2 × 10 2×6 2×6 6 ... 15 2 × 10 2 × 10 2 × 10 10 ... 15 50 8WH1 000-0AN00, 8WH1 000-0AN01, 8WH1 000-0CN07 2 × 10 2 × 10 2 × 10 2 × 10 -- 2 × 35 2 × 35 2 × 35 2 × 35 -- 16 6) 2 × 10 70 8WA1 206 2 × 10 2 × 10 2 × 10 2 × 10 10 ... 12 6) 2 × 16 2 × 16 2 × 16 2 × 16 16 ... 12 7) 95 8WH1 000-0AQ00, 8WH1 000-0AQ01, 8WH1 000-0CQ07 2 × 25 2 × 25 2 × 25 2 × 25 -- 2 × 35 2 × 35 2 × 35 2 × 35 -- 150 8WH1 000-0AS00, 8WH1 000-0AS01 2 × 25 2 × 25 2 × 25 2 × 25 -- 2 × 50 2 × 50 2 × 50 2 × 50 -- 240 8WH1 000-0AU00, 8WH1 000-0AU01 2 × 35 2 × 35 2 × 35 2 × 35 -- 2 × 95 2 × 95 2 × 95 2 × 95 -- 1) End sleeves acc. to DIN 46 228 Sheet 1 without insulation. Size corresponds to sleeve nominal size. 4) At voltages > 500 V, shorten end sleeves with inserted conductor to 10 mm before pressing on. 2) 0.12/0.25 mm² corresponds to 0.4/0.6 mm. For 0.75 mm² conductors, use end sleeves 1-10 and press on with insert E1 or PZ 1.5. 5) Tested up to 16 mm². Fit and press on two end sleeves one after the other (up to stop). Voltage reduction to 630 V required. 3) 6) 7) Conductor cross-sections to AWG "American Wire Gauge" AWG No. Wire diameter Cross-section mm mm² 30 0.254 0.051 29 0.287 28 AWG No. Wire diameter Cross-section mm mm² 18 1.024 0.82 0.065 17 1.151 0.320 0.081 16 27 0.363 0.102 26 0.404 25 AWG No. Wire diameter Cross-section mm mm² 6 4.115 13.30 1.04 5 4.620 16.77 1.290 1.31 4 5.189 21.15 15 1.450 1.65 3 5.827 26.66 0.128 14 1.628 2.08 2 6.543 33.62 0.455 0.163 13 1.829 2.63 1 7.348 42.41 24 0.511 0.205 12 2.052 3.31 1/0 8.252 53.52 23 0.574 0.259 11 2.304 4.17 2/0 9.266 67.43 22 0.643 0.33 10 2.588 5.26 3/0 10.404 85.01 21 0.724 0.41 9 2.906 6.63 4/0 11.684 107.21 20 0.813 0.52 8 3.268 8.37 5/0 -- 135.35 19 0.912 0.65 7 3.665 10.55 6/0 -- 170.50 9/7 9 8WA1 Screw Terminals General data on 8WA s and U rating Terminal size Type CSA rating AWG mm² Rated voltage Ue AWG Rated current In Rated voltage Ue A V A V 8WA1 011-1SF12 8WA1 011-1SF24, -2SF24, -4SF24 8WA1 011-1SF25, -2SF25, -4SF25 18-14 14 14 6.3 1 2 600 --- 18-14 14-12 14-12 6.3 1 2 600 AC240/DC60 AC240/DC60 8WA1 011-1SF26, -2SF26, -4SF26 8WA1 011-1SF27, -2SF27, -4SF27 8WA1 011-1SF28, -2SF28, -4SF28 14 14 14 4 6 10 ---- 14-12 14-12 14-12 4 6 10 AC240/DC60 AC240/DC60 AC240/DC60 8WA1 011-1BF21, -1BF22, -1BF23, -1PF11 8WA1 011-1DF11, -3DF21, -0DF21, -0DF22 8WA1 011-1NF01, -1NF02 18-12 18-12 22-12 25 25 26 600 600 600 22-12 22-12 22-12 26 26 26 600 600 600 8WA1 011-3JF.. 8WA1 011-1PF00, 8WA1 011-1PF01 8WA1 501 -22-12 22-12 --10 --300 D 22-12 22-12 22-12 26 -10 300 -300 8WA1 011-1PG00, 8WA1 011-1PG01 18-10 8WA1 011-1BG11, -1BG21, -1BG22 18-10 8WA1 011-1DG11, -3DG21, -0DG21, -0DG22 18-10 -40 40 -600 600 18-10 18-10 18-10 -35 35 -600 600 8WA1 011-1NG31, -1NG32 8WA1 011-1PG11 8WA1 011-2BG11, -2DG11 18-10 18-10 18-10 40 40 40 600 600 300 18-10 -18-10 35 -35 600 -600 8WA1 011-6BG11, -6DG11 8WA1 011-6EG.. 8WA9 200 18-10 -18-10 40 -25 300 -300 18-10 18-10 18-10 35 34 26 600 300 600 8WA1 011-1PH00 8WA1 011-1BH23, -1PH11 8WA1 011-1DH11, -3DH21 -16-10 16-8 -35 35 -600 600 14-8 14-8 14-8 -44 44 -600 600 8WA1 011-1NH01, -1NH02 8WA1 011-1MH10, -1MH11, -1MH15 8WA1 232 14-8 16-10 -- 44 35/40 -- 600 600/300 C/D -- 14-8 14-8 -- 1) 44 44 24 600 600/300 600 8WA1 011-1BK11 8WA1 011-1NK02 8WA1 011-1PK00 14-6 -12-4 70 --- 600 --- 12-4 12-4 12-4 79 73 -- 600 300 -- 8WA1 012-1DK10 8WA1 204, 8WA1 304 8WA1 604 -14-6 -- -70 -- -600 -- -12-4 12-4 79 79 73 600 600 300 25 8WH1 060-0AL00 6-4 100 600 6-4 85 600 35 8WA1 011-1BM11 8WA1 011-1PM00 8WA1 205, 8WA1 305 12-2 10-1 12-2 100 -100 600 -600 10-1 10-1 10-1 120 -120 600 -600 50 8WH1 000-0AN00, 8WH1 000-0AN01 6-0 125 600 6-0 150 600 8WH1 000-0CN07 -- -- -- 6-1 8WH1 060-0AN00 6-0 125 600 6-0 150 600 70 8WA1 012-1DP14 8WA1 206 2/0-1 8-1/0 170 150 600 600 6-3/0 8-3/0 -220 600 600 95 8WH1 000-0AQ00, 8WH1 000-0AQ01 1-000 220 600 2-000 230 600 8WH1 000-0CQ07 2-4 8WH1 060-0AQ00 2-000 200 600 2-000 230 600 8WH1 000-0AS0, 8WH1 000-0AS01 2 - 300 kcmil 275 600 2 - 300 kcmil 285 600 8WH1 060-0AS00 2 - 300 kcmil 275 600 2 - 300 kcmil 285 600 8WH1 000-0AU00, 8WH1 000-0AU01 0 - 500 kcmil 400 600 0 - 500 kcmil 380 600 8WH1 000-0AU00 0 - 500 kcmil 400 600 0 - 500 kcmil 380 600 1.5 2.5 4 6 9 16 150 240 1) UR rating Rated current In Plug-in connection 9/8 2-4 8WA1 Screw Terminals 8WA through-type terminals ■ Selection and ordering data Version Order No. MOQ* General details • Thermoplastic insulating body • Screw terminal at both ends • Enclosed at both ends Note Section Page For labeling accessories, see ... Accessories 8/2 Terminal size 2.5 mm² Through-type terminals, terminal size 2.5 mm² • Rated uninterrupted current 24 A • Rated insulation voltage 800 V • Mounting width 6 mm • Terminal height 26 mm • Terminal length 41 mm • U AWG 22-12 • s AWG 18-12 8WA1 011-1DF11 Versions • Single terminals - Beige - Blue - Red - 8WA1 011-3DF21 Orange Yellow Black Green • Terminal blocks - Beige, 3-pole, width 18 mm - Beige, 10-pole, width 61 mm, with designation 1 ... 10 - Beige, 10-pole, width 61 mm, without inscription Accessories 8WA1 011-0DF21 8WA1 011-1DF11 8WA1 011-1BF23 8WA1 011-1BF21 100 units 50 units 50 units 8WA1 011-1BF22 8WA1 011-1BF26 8WA1 011-1BF24 8WA1 011-1BF25 50 units 50 units 50 units 50 units 8WA1 011-3DF21 8WA1 011-0DF22 8WA1 011-0DF21 10 units 20 units 20 units Section Page Accessories 9/13 8WA1 810 50 units Accessories 9/13 8WA1 860 50 units Accessories Accessories 9/13 9/13 8WA1 822-7AX01 8WA1 822-7AX03 10 units 10 units • Jumpers, for terminal size 2.5 mm² Accessories 9/13 8WA1 822-7VF01 • Test sockets Accessories 9/14 8WA1 854 100 units • Disconnecting links Accessories 9/14 8WA1 865 50 units • Covers - With lightning symbol, for terminal size 1.5 to 2.5 mm² - White, facility for inscription, for terminal size 1.5 to 2.5 mm² - For connection bars Y Transparent, for terminal size 2.5 to 6 mm² Y White, facility for inscription, for terminal size 2.5 to 6 mm² 50 units Note Between terminals with terminal sizes 2.5 and 6 mm², two 8WH1 820 barriers are required. • Insulation plates, for terminal size 2.5 to 6 mm² Accessories 9/14 8WA1 825 50 units • Connection bars, for terminal size 2.5 mm² - For two terminals - For three terminals - For four terminals - For ten terminals Accessories Accessories Accessories Accessories 9/14 9/14 9/14 9/14 8WA1 895 8WA1 896 8WA1 897 8WA1 898 50 units 50 units 20 units 10/200 units • Barriers, for terminal size 1.5 to 4 mm² Accessories 9/14 8WA1 820 50 units 8WA1 011-1PF01 8WA1 011-1PF00 50 units 50 units 8WA1 820 50 units PE through-type terminals, terminal size 2.5 mm² • Green/yellow • Mounting width 6 mm • Terminal height 26 mm • Terminal length 51 mm Versions 8WA1 011-1PF01 • One screw terminal • Two screw terminals Accessories Section Page Barriers, for terminal size 1.5 to 4 mm² Accessories 9/14 * You can order this quantity or a multiple thereof. 9/9 9 8WA1 Screw Terminals 8WA through-type terminals Version Order No. MOQ* Terminal size 4 mm² Through-type terminals, terminal size 4 mm² • Rated uninterrupted current 32 A • Rated insulation voltage 800 V • Mounting width 6.5 mm • Terminal height 30 mm • Terminal length 41 mm • U AWG 18-10 • s AWG 18-10 Versions 8WA1 011-1DG11 • Single terminals - Beige - Blue - Red - Orange - Black • Terminal blocks - Beige, 3-pole, width 19.5 mm - Beige, 10-pole, width 65.5 mm, labeled 1 ... 10 - Beige, 10-pole, width 65.5 mm, without inscription 8WA1 011-0DG21 Accessories 100 units 50 units 50 units 8WA1 011-1BG22 8WA1 011-1BG24 50 units 50 units 8WA1 011-3DG21 8WA1 011-0DG22 8WA1 011-0DG21 10 units 20 units 20 units Section Page Accessories 9/13 8WA1 811 50 units Accessories 9/13 8WA1 862 50 units Accessories Accessories 9/13 9/13 8WA1 822-7AX01 8WA1 822-7AX03 10 units 10 units • Jumpers, for terminal size 4 mm² Accessories 9/13 8WA1 822-7VG00 50 units • Terminal strips Accessories 9/14 8WA1 741-2X • Test sockets Accessories 9/14 8WA1 854 100 units • Disconnecting links Accessories 9/14 8WA1 865 50 units • Covers - With lightning symbol, for terminal size 4 and 6 mm² - White, facility for inscription, for terminal size 4 and 6 mm² - For connection bars Y Transparent, for terminal size 2.5 to 6 mm² Y White, facility for inscription, for terminal size 2.5 to 6 mm² 9 8WA1 011-1DG11 8WA1 011-1BG11 8WA1 011-1BG21 5 units Note Between terminals with terminal sizes 2.5 and 6 mm², two 8WH1 820 barriers are required. • Insulation plates, for terminal size 2.5 to 6 mm² Accessories 9/14 8WA1 825 50 units • Connection bars, for terminal size 4 mm² - For two terminals - For three terminals - For four terminals - For ten terminals Accessories Accessories Accessories Accessories 9/14 9/14 9/14 9/14 8WA1 850 8WA1 851 8WA1 852 8WA1 853 50 units 50 units 20 units 10 units • Barriers, for terminal size 1.5 to 4 mm² Accessories 9/14 8WA1 820 50 units 8WA1 011-1PG01 8WA1 011-1PG00 50 units 50 units 8WA1 820 50 units PE through-type terminals, terminal size 4 mm² • Green/yellow • Mounting width 7.2 mm • Terminal height 30 mm • Terminal length 51 mm •Us Versions 8WA1 011-1PG01 9/10 • One screw terminal • Two screw terminals Accessories Section Page Barriers, for terminal size 1.5 to 4 mm² Accessories 9/14 * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA through-type terminals Version Order No. MOQ* Terminal size 6 mm² Through-type terminals, terminal size 6 mm² • Rated uninterrupted current 41 A • Rated insulation voltage 800 V • Mounting width 8 mm • Terminal height 33 mm • Terminal length 41 mm • U AWG 14-8 • s AWG 16-8 Versions 8WA1 011-1DH11 • Single terminals - Beige - Blue - Black 8WA1 011-1DH11 8WA1 011-1BH23 8WA1 011-1BH24 50 units 50 units 50 units 8WA1 011-3DH21 20 units 9/13 8WA1 811 50 units 9/13 8WA1 862 50 units 9/13 8WA1 822-7AX01 10 units • Terminal blocks - Beige, 3-pole, width 24.5 mm Accessories 8WA1 011-3DH21 Section • Covers - With lightning symbol, for terminal size Accessories 4 to 6 mm² - White, facility for inscription, for terminal size Accessories 4 and 6 mm² - For connection bars, transparent, for terminal size Accessories 2.5 to 6 mm² Page • Jumpers, for terminal size 6 mm² Accessories 9/13 8WA1 822-7VH00 • Test sockets Accessories 9/14 8WA1 854 100 units 50 units • Disconnecting links Accessories 9/14 8WA1 865 50 units Note Between terminals with terminal sizes 2.5 and 6 mm², two 8WH1 820 barriers are required. • Insulation plates, for terminal size 2.5 to 6 mm² Accessories 9/14 8WA1 825 50 units • Connection bars, for terminal size 6 mm² - For two terminals - For three terminals - For four terminals - For ten terminals Accessories Accessories Accessories Accessories 9/14 9/14 9/14 9/14 8WA1 885 8WA1 886 8WA1 887 8WA1 888 50 units 50 units 20 units 10 units • Barriers, for terminal size 6 and 16 mm² Accessories 9/14 8WA1 821 50 units 8WA1 010-1PH01 50 units 8WA1 821 50 units 8WA1 011-1PH00 50 units 8WA1 821 50 units PE through-type terminals, terminal size 6 mm², one screw terminal • Bare • Mounting width 6 mm • Terminal height 25 mm • Terminal length 44 mm • Also for use as shield terminal 8WA1 010-1PH01 Accessories Section Page Barriers, for terminal size 6 and 16 mm² Accessories 9/14 PE through-type terminals, terminal size 6 mm², two screw terminals • Green/yellow • Mounting width 8 mm • Terminal height 33 mm • Terminal length 51 mm •Us 8WA1 011-1PH00 Accessories Section Page Barriers, for terminal size 6 and 16 mm² Accessories 9/14 * You can order this quantity or a multiple thereof. 9/11 9 8WA1 Screw Terminals 8WA through-type terminals Version Order No. MOQ* Terminal size 16 mm² Through-type terminals, terminal size 16 mm² • Rated uninterrupted current 76 A • Rated insulation voltage 800 V • Mounting width 10 mm • Terminal height 38 mm • Terminal length 41 mm • U AWG 12-4 • s AWG 14-6 Versions 8WA1 204 • Single terminals - Beige - Blue • Terminal blocks - 3-pole, width 30 mm Accessories 8WA1 304 9 Section • Covers - With lightning symbol, for terminal size 16 mm² Accessories - White, facility for inscription, for terminal size 16 Accessories mm² - For connection bars, transparent, for terminal size Accessories 16 and 35 mm² 8WA1 204 8WA1 011-1BK11 20 units 10 units 8WA1 304 20 units 9/13 9/13 8WA1 812 8WA1 892 50 units 50 units 9/13 8WA1 822-7AX02 10 units Page • Insulation plates, for terminal size 16 and 35 mm² Accessories 9/14 8WA1 822-7TK00 50 units • Connection bars, for terminal size 16 mm² - For two terminals - For three terminals - For four terminals - For ten terminals Accessories Accessories Accessories Accessories 9/14 9/14 9/14 9/14 8WA1 842 8WA1 845 8WA1 848 8WA1 802 20 units 20 units 10 units 10 units • Barriers, for terminal size 6 and 16 mm² Accessories 9/14 8WA1 821 50 units 8WA1 011-1PK00 25 units 8WA1 821 50 units 8WA1 205 8WA1 011-1BM11 20 units 10 units 8WA1 305 20 units 9/13 9/13 8WA1 813 8WA1 893 50 units 50 units 9/13 8WA1 822-7AX02 10 units PE through-type terminals and through-type PEN terminals, terminal size 16 mm² • Green/yellow • for I = 76 A • Mounting width 12 mm • Terminal height 38 mm • Terminal length 53 mm • Two screw terminals •Us 8WA1 011-1PK00 Accessories Section Page Barriers, for terminal size 6 and 16 mm² Accessories 9/14 Terminal size 35 mm² Through-type terminals, terminal size 35 mm² • Rated uninterrupted current 125 A • Rated insulation voltage 800 V • Mounting width 16 mm • Terminal height 50 mm • Terminal length 53 mm • U AWG 10-1 • s AWG 12-2 Versions 8WA1 205 • Single terminals - Beige - Blue • Terminal blocks - 3-pole, width 48 mm Accessories 8WA1 305 9/12 Section • Covers - With lightning symbol, for terminal size 35 mm² Accessories - White, facility for inscription, for terminal size 35 Accessories mm² - For connection bars, transparent, for terminal size Accessories 16 and 35 mm² Page • Insulation plates, for terminal size 16 and 35 mm² Accessories 9/14 8WA1 822-7TK00 50 units • Connection bars, for terminal size 35 mm² - For two terminals - For three terminals - For ten terminals Accessories Accessories Accessories 9/14 9/14 9/14 8WA1 828 8WA1 803 8WA1 804 20 units 20 units 10 units • Barriers, for terminal size 35 mm² Accessories 9/14 8WA1 823 25 units * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA through-type terminals Version Order No. PE through-type terminals and through-type PEN terminals, terminal size 35 mm² • Green/yellow • for I = 125 A • Mounting width 16 mm • Terminal height 50 mm • Terminal length 53 mm • Two screw terminals •Us 8WA1 011-1PM00 25 units 8WA1 823 25 units Accessories Section Page Barriers, for terminal size 35 mm² Accessories 9/14 8WA1 011-1PM00 MOQ* Terminal size 70 mm² Through-type terminals, terminal size 70 mm² • Rated uninterrupted current 192 A • Rated insulation voltage 800 V • Mounting width 25 mm • Terminal height 64.5 mm • Terminal length 73.5 mm • U AWG 8-3/0 • s AWG 8-1/0 Versions 8WA1 206 • Beige • Blue 8WA1 206 8WA1 011-1BP11 10/60 units 10 units Accessories Section Page • Covers, with lightning symbol, for terminal size 70 mm² • Connection bars, for terminal size 70 mm², for 2 terminals • Barriers, for terminal size 70 mm² Accessories 9/13 8WA1 814 50 units Accessories 9/14 8WA1 216 20 units Accessories 9/14 8WA1 824 25 units 8WA1 810 8WA1 811 50 units 50 units 50 units Accessories Covers Versions • With lightning symbol - For terminal size 1.5 ... 2.5 mm² - For terminal sizes 4 and 6 mm² 8WA1 810 - For terminal size 16 mm² - For terminal size 35 mm² - For terminal size 70 mm² 8WA1 812 8WA1 813 8WA1 814 50 units 50 units • White, facility for inscription - For terminal size 1.5 ... 2.5 mm² - For terminal sizes 4 and 6 mm² - For terminal size 16 mm² - For terminal size 35 mm² 8WA1 860 8WA1 862 8WA1 892 8WA1 893 50 units 50 units 50 units 50 units • For connection bars, transparent - For terminal size 2.5 ... 6 mm² - For terminal sizes 16 and 35 mm² 8WA1 822-7AX01 8WA1 822-7AX02 10 units 10 units 8WA1 822-7AX03 10 units • For terminal size 2.5 mm² • For terminal size 4 mm² • For terminal size 6 mm² 8WA1 822-7VF01 8WA1 822-7VG00 8WA1 822-7VH00 50 units 50 units 50 units End retainers, thermoplastic Width 10 mm 8WA1 808 50 units 8WA1 860 8WA1 822-7AX01 • For connection bars, white, facility for inscription, for terminal size 2.5 to 6 mm² Jumpers For connection bars Versions 8WA1 822-7VF01 8WA1 808 * You can order this quantity or a multiple thereof. 9/13 9 8WA1 Screw Terminals 8WA through-type terminals Version Order No. MOQ* Terminal strips • 6-pole • Labeled 1 to 6 8WA1 741-2X 5 units Test sockets • Ø 2.3 mm • Up to 10 A • Terminal size 2.5 to 6 mm² 8WA1 854 100 units • Red • Blue 8WA1 868 8WA1 870 10 units 10 units Disconnecting links Up to 32 A 8WA1 865 50 units 8WA1 825 8WA1 822-7TK00 50 units 50 units 8WA1 741-2X 8WA1 854 Test plugs • For 8WA1 and 8WA2 terminals with 2.3 mm ø hole or 8WA1 854, 8WA1 884 test sockets • Uninterrupted current 10 A Versions 8WA1 868 9 Note Between terminals with terminal sizes 2.5 and 6 mm², two 8WH1 820 barriers are required. 8WA1 865 Insulation plates Versions 8WA1 825 • For terminal size 2.5 ... 6 mm² • For terminal sizes 16 and 35 mm² Connection bars Versions 8WA1 895 • For terminal size 2.5 mm² - For two terminals - For three terminals - For four terminals - For ten terminals 8WA1 895 8WA1 896 8WA1 897 8WA1 898 50 units 50 units 20 units 10/200 units • For terminal size 4 mm² - For two terminals - For three terminals - For four terminals - For ten terminals 8WA1 850 8WA1 851 8WA1 852 8WA1 853 50 units 50 units 20 units 10 units • For terminal size 6 mm² - For two terminals - For three terminals - For four terminals - For ten terminals 8WA1 885 8WA1 886 8WA1 887 8WA1 888 50 units 50 units 20 units 10 units • For terminal size 16 mm² - For two terminals - For three terminals - For four terminals - For ten terminals 8WA1 842 8WA1 845 8WA1 848 8WA1 802 20 units 20 units 10 units 10 units • For terminal size 35 mm² - For two terminals - For three terminals - For ten terminals 8WA1 828 8WA1 803 8WA1 804 20 units 20 units 10 units • For terminal size 70 mm² - For two terminals 8WA1 216 20 units 8WA1 820 8WA1 821 8WA1 823 8WA1 824 50 units 50 units 25 units 25 units Barriers Versions 8WA1 820 9/14 • • • • For terminal size 1.5 ... 4 mm² For terminal sizes 6 and 16 mm² For terminal size 35 mm² For terminal size 70 mm² * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA N-conductor isolating and branch terminals ■ Overview N-conductor isolating terminals permit an insulation test to be performed without disconnecting the neutral conductor according to DIN VDE 0108 and DIN VDE 0100 (Standards for the erection of power installations). The branch terminals are used for the connection of lines (L), for example for power supplies, to the 6 mm x 6 mm busbar. The rated voltage between two branch terminals (1 slide open) is 289 V. When they are used as shield terminals according to DIN VDE 0160, they provide isolation between the central reference point (shield connection conductor) and the PE conductor. ■ Selection and ordering data Version Order No. MOQ* General details • 1 screw terminal and connection to the neutral conductor bar or 6 mm × 6 mm busbar acc. to DIN 1761 • Insulating body made of blue or beige thermoplastic • Enclosed at both ends Note Section Page For labeling accessories, see ... Accessories 10/2 Terminal size 2.5 mm² 8WA1 011-1NF01 8WA1 011-1NF01 N-conductor isolating terminal, terminal size 2.5 mm² • Blue • Rated uninterrupted current 24 A • Rated insulation voltage 500 V • Mounting width 6 mm • Terminal height 35 mm • Terminal length 55 mm • With built-in test socket in the fixed part of the terminal • U AWG 22-12 • s AWG 22-12 50 units 9 Accessories Section Page • Covers, for connection bars • N-busbars, 6 mm × 6 mm • Label holders Accessories Accessories Accessories 9/16 9/16 9/16 Branch terminals, terminal size 2.5 mm² • Beige • Isolating distance 400 V • Mounting width 6 mm • Terminal height 35 mm • Terminal length 55 mm • With built-in test socket in the fixed part of the terminal • Isolating distance • U AWG 22-12 • s AWG 22-12 Accessories Section Page • Covers, for connection bars • N-busbars, 6 mm × 6 mm • Label holders Accessories Accessories Accessories 9/16 9/16 9/16 8WA1 822-7AX00 8GF9 324-2 3TX4 210-0J 10 units 10 units 100 units 8WA1 011-1NF02 50 units 8WA1 822-7AX00 8GF9 324-2 3TX4 210-0J 10 units 10 units 100 units 8WA1 011-1NG31 50 units 8WA1 822-7AX00 8WA2 867 8GF9 324-2 3TX4 210-0J 10 units 50 units 10 units 100 units Terminal size 4 mm² 8WA1 011-1NG31 N-conductor isolating terminal, terminal size 4 mm² • Blue • Rated uninterrupted current 32 A • Rated insulation voltage 500 V • Mounting width 6.5 mm • Terminal height 35 mm • Terminal length 55 mm • With built-in test socket in the fixed part of the terminal • U AWG 18-10 • s AWG 18-10 Accessories Section Page • • • • Accessories Accessories Accessories Accessories 9/16 9/16 9/16 9/16 Covers, for connection bars Feeder terminals, for N-busbars N-busbars, 6 mm × 6 mm Label holders * You can order this quantity or a multiple thereof. 9/15 8WA1 Screw Terminals 8WA N-conductor isolating and branch terminals Version Order No. MOQ* N-conductor isolating terminals, terminal size 6 mm² • Blue • Rated uninterrupted current 41 A • Rated insulation voltage 500 V • Mounting width 8 mm • Terminal height 35 mm • Terminal length 55 mm • With built-in test socket in the fixed part of the terminal • U AWG 14-8 • s AWG 14-8 8WA1 011-1NH01 50 units 8WA1 822-7AX00 8GF9 324-2 3TX4 210-0J 10 units 10 units 100 units Terminal size 6 mm² 8WA1 011-1NH01 Accessories Section Page • Covers, for connection bars • N-busbars, 6 mm × 6 mm • Label holders Accessories Accessories Accessories 9/16 9/16 9/16 Terminal size 16 mm² N-conductor isolating terminals, terminal size 16 mm² • Blue • Rated uninterrupted current 76 A • Rated insulation voltage 500 V • Mounting width 10 mm • Terminal height 35 mm • Terminal length 55 mm • U AWG 12-4 8WA1 604 9 8WA1 604 Accessories Section Page • • • • Accessories Accessories Accessories Accessories 9/16 9/16 9/16 9/16 Covers, for connection bars Feeder terminals, for N-busbars N-busbars, 6 mm × 6 mm Label holders 50 units 8WA1 822-7AX00 8WA2 868 8GF9 324-2 3TX4 210-0J 10 units 50 units 10 units 100 units 8WA1 011-1NK02 50 units 8WA1 822-7AX00 8GF9 324-2 3TX4 210-0J 10 units 10 units 100 units 8WA1 822-7AX00 10 units • Rated uninterrupted current 32 A, for connection of up to 4 mm 2 • Rated uninterrupted current 76 A, for connection of up to 25 mm 2 • Rated uninterrupted current 125 A, for connection of up to 35 mm 2 8WA2 867 50 units 8WA2 868 50 units 8WA2 870 50 units N-busbars, 6 mm × 6 mm • Rated uninterrupted current 125 A • 1109 mm long • For four-field 8GF9 324-2 10 units 3TX4 210-0J 100 units Branch terminals, terminal size 16 mm² • Beige • Isolating distance 400 V • Mounting width 10 mm • Isolating distance • U AWG 12-4 Accessories Section Page • Covers, for connection bars • N-busbars, 6 mm × 6 mm • Label holders Accessories Accessories Accessories 9/16 9/16 9/16 Accessories 8WA1 822-7AX00 Covers, for connection bars • Not for 8WA1 604 and 8WA1 011-1NK02 • Length 155 mm Feeder terminals, for N-busbars • 6 × 6 mm and 10 × 3 mm • Bare Versions 8WA2 870 / 868 / 867 Note Prices apply for orders from € 25.00. For orders below € 25.00, a processing charge of € 2.50 net will be added. 8GF9 324-2 Label holders 9/16 * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA Insta or three-tier terminals ■ Overview The Insta or three-tier terminals incorporate up to 3 different terminal functions in one insulating body of 6 mm width. The width of 3 Insta terminals corresponds to the modular width of 18 mm standardized in distribution board assembly. Tools are required to remove the terminals from the support rail. All clamping points for incoming and outgoing cables have a cutout for an 8WA8 8.. label. The protective conductor connections are already marked green-yellow and the neutral conductor connections blue. The N-busbar has the same position for Insta terminals and Nconductor isolating terminals. This allows, for example, the use of a 16 mm² N-conductor isolating terminal as an infeed for the N-busbar. 8WA1 011-3JF16, -3JF17 and -3JF18 allow the N-busbar to be routed with a mounting depth of 42.5 mm. PE, L, NT Insta terminal The 8WA1 011-3JF20 terminal is the basic version for AC circuits. It comprises: • Protective conductor connection • Through-type connection for one phase conductor • Neutral conductor connection that can be isolated from the 6 mm × 6 mm N-busbar. PE, L, N Insta terminals If no neutral conductor isolation is required, the 8WA1 011-3JF17 terminal is used: • Protective conductor connection • Through-type connection for one phase conductor • Through-type connection for the neutral conductor PE, L, L Insta terminal Design of 8WA1 011-3JF16 terminal as previous version. Instead of the through-type connection for the neutral conductor, a through-type connection for a second phase conductor is fitted. L, L Insta terminal 8AW1 011-3JF18 terminal contains two through-type connections for two phase conductors. These are generally used for three-phase outgoing lines. 9 ■ Selection and ordering data Version Order No. MOQ* General details • Thermoplastic insulating body • Screw terminal at both ends • Enclosed at both ends • Neutral terminal, 6 mm × 6 mm neutral conductor connection Note Section Page For labeling accessories, see ... Accessories 10/2 Terminal size 2.5 mm² 8WA1 011-3JF16 Insta terminals, terminal size 2.5 mm² • Rated uninterrupted current 24 A • Rated insulation voltage - 400 V between phase conductors - 250 V between phase and protective conductors and for neutral isolating distance • Mounting width 6 mm • Terminal height 42.5 mm • Terminal length 87 mm • Screw terminals at both ends • U AWG 22-12 Circuit diagram N/L Type PE, L, L 8WA1 011-3JF16 50 units PE, L, N 8WA1 011-3JF17 50 units L, L 8WA1 011-3JF18 50 units PE, L, NT 8WA1 011-3JF20 50 units 8WA1 822-7TH00 50 units L PE NSH0_00020 N/L L PE NSH0_00020 L L NSH0_00021 NT L PE NSH0_00022 Accessories Section Barriers, for Insta terminals, terminal size 2.5 mm and Accessories measuring transformer terminals, terminal size 6 * You can order this quantity or a multiple thereof. Page 9/18 9/17 8WA1 Screw Terminals 8WA Insta or three-tier terminals Version Order No. MOQ* 8WA1 811 8WA1 862 50 units 50 units 8WA1 822-7AX01 8WA1 822-7AX03 10 units 10 units • Connection up to 4 mm² • Connection up to 25 mm² • Connection up to 35 mm² 8WA2 867 8WA2 868 8WA2 870 50 units 50 units 50 units End retainers, thermoplastic Width 10 mm 8WA1 808 50 units Device labels For end retainer, blank label 3TX4 210-0H Insulation carriers, for mounting insulated support rails 8WA1 857 Blank labels For terminal marking 8WA8 848-2AY N-busbars, 6 mm × 6 mm • Rated uninterrupted current 125 A • 1109 mm long • For four-field 8GF9 324-2 10 units 8WA1 822-7VF02 8WA1 822-7VF03 8WA1 822-7VF04 8WA1 822-7VF10 50 units 50 units 20 units 10 units 8WA1 822-7TH00 50 units Accessories Covers Up to three terminals side-by-side Versions • With lightning symbol, for terminal size 4 and 6 mm² • White, facility for inscription, for terminal size 4 and 6 mm² • For connection bars, for terminal size 2.5 to 6 mm² - Transparent - White Feeder terminals, for N-busbars • 6 mm × 6 mm and 10 mm × 3 mm • Bare Versions 8WA2 870 / 868 / 867 8WA1 808 9 100 units 20 units 8WA1 857 100 units Note Prices apply for orders from € 25.00. For orders below € 25.00, a processing charge of € 2.50 net will be added. 8GF9 324-2 Connection bars, for Insta terminals Versions • • • • For two terminals For three terminals For four terminals For ten terminals Barriers, for Insta terminals, terminal size 2.5 mm² and measuring transformer terminals, terminal size 6 mm² 9/18 * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA two-tier terminals ■ Overview ■ Technical specifications Two-tier terminals are a compact form of the terminal blocks. They are therefore open on one side. They can contain two connecting cables with two connections each or they can be laid out as terminal blocks with four connections on the same potential. An advantage is the standardized front for mounting, linking and labeling. Rated voltage AC DC Between connection bars • With insulation plate • With end plate or barrier • With disconnecting link opened 400 V 800 V 500 V 450 V 900 V 600 V For alternately bent soldering tags 400 V 450 V For adjacent terminals with soldering tags 250 V and insulated plugs 300 V ■ Selection and ordering data Version Order No. MOQ* General details • Thermoplastic insulating body • Screw terminal at both ends Note Section Page For labeling accessories, see ... Accessories 10/2 Terminal size 4 mm² Two-tier terminals, terminal size 4 mm² • Rated uninterrupted current 32 A • Rated insulation voltage 690 V (with end plate 800 V) • Mounting width 6.5 mm • Terminal height 45 mm • Terminal length 64 mm • U AWG 18-10 • s AWG 18-10 8WA1 011-6DG11 Versions • Beige - 1-pole - 2-pole, with two isolated connections • Blue - 1-pole - 2-pole, with two isolated connections Accessories 8WA1 011-2DG11 9 Section • Covers - With lightning symbol, for terminal size 4 and 6 mm² Accessories - White, facility for inscription, for terminal size 4 and 6 Accessories mm² - For connection bars, for terminal size 2.5 to Accessories 6 mm², transparent 8WA1 011-6DG11 8WA1 011-2DG11 50 units 50 units 8WA1 011-6BG11 8WA1 011-2BG11 50 units 50 units 9/20 9/20 8WA1 811 8WA1 862 50 units 50 units 9/20 8WA1 822-7AX01 10 units Page • Jumpers - For upper tier of 2-pole terminals - For lower tier of 1 and 2-pole terminals Accessories Accessories 9/20 9/20 8WA1 822-7VG00 8WA1 822-7VG01 50 units 50 units • Spacer sleeves Accessories 9/20 8WA1 822-7VH11 100 units • End plates Accessories 9/20 8WA1 817 50 units • Test sockets - For upper tier of 2-pole terminals - For lower tier of 1 and 2-pole terminals Accessories Accessories 9/20 9/20 8WA1 854 8WA1 884 100 units 100 units • Disconnecting links Accessories 9/20 8WA1 865 50 units • Insulation plates - For upper tier of 2-pole terminals - For lower tier of 1 and 2-pole terminals Accessories Accessories 9/20 9/20 8WA1 825 8WA1 825 50 units 50 units Accessories Accessories Accessories Accessories 9/20 9/20 9/20 9/20 8WA1 850 8WA1 851 8WA1 852 8WA1 853 50 units 50 units 20 units 10 units Accessories Accessories 9/20 9/20 8WA1 835 8WA1 838 50 units 10 units Accessories 9/20 8WA1 823 25 units • Connection bars - For upper tier of 2-pole terminals Y For two terminals Y For three terminals Y For four terminals Y For ten terminals - For lower tier of 1 and 2-pole terminals Y For two terminals Y For ten terminals • Barriers * You can order this quantity or a multiple thereof. 9/19 8WA1 Screw Terminals 8WA two-tier terminals Version Order No. MOQ* • With lightning symbol, for terminal size 4 and 6 mm² 8WA1 811 50 units • White, facility for inscription, for terminal size 4 and 6 mm² 8WA1 862 50 units • For connection bars, for terminal size 2.5 to 6 mm², transparent 8WA1 822-7AX01 10 units • For upper tier of 2-pole terminals • For lower tier of 1 and 2-pole terminals 8WA1 822-7VG00 8WA1 822-7VG01 50 units 50 units End plates, for two-tier terminals 8WA1 817 50 units 8WA1 854 8WA1 884 100 units 100 units Spacer sleeves • For lower tier of 1 and 2-pole terminals • Suitable for 2.3 mm test socket 8WA1 822-7VH11 100 units Disconnecting links For upper tier of 2-pole terminals 8WA1 865 50 units 8WA1 825 50 units 8WA1 850 8WA1 851 8WA1 852 8WA1 853 50 units 50 units 20 units 10 units 8WA1 835 8WA1 838 50 units 10 units 8WA1 823 25 units Accessories Covers Versions 8WA1 811 8WA1 862 8WA1 822-7AX01 Jumpers • For connection bars • For terminal size 4 mm² Versions 9 Test sockets Ø 2.3 mm Versions 8WA1 854 • For upper tier of 2-pole terminals • For lower tier of 1 and 2-pole terminals Accessories Note The terminals must be fitted with end plates and must be fitted with the end plates facing each other. 8WA1 865 Insulation plates, for terminal size 2.5 to 6 mm² 8WA1 825 Connection bars Versions • For upper tier of 2-pole terminals - For two terminals - For three terminals - For four terminals - For ten terminals • For lower tier of 1 and 2-pole terminals - For two terminals - For ten terminals Barriers 8WA1 823 9/20 * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA two-tier terminals with electronic components ■ Design 5 4b 4a 9 7 10 3 6 1 End plate 2 Barrier 3 Insulation plate 4a Connection bar for lower tier 4b Connection bar for upper tier 0 02 14 1_ I20 5 Link for connection bar 6 Jumper 7 Test socket 2 8 Soldering tag 8 9 Flat connector, slotted 10 Cover with lightning symbol 1 9 ■ Selection and ordering data Version Order No. MOQ* General details • Thermoplastic insulating body • Screw terminal at both ends • Open on one side • Beige Note Section Page For labeling accessories, see ... Accessories 10/2 Terminal size 4 mm² Diode terminals, terminal size 4 mm² • Rated insulation voltage 250 V • Mounting width 6.5 mm • Terminal height 45 mm • Terminal length 64 mm • U AWG 18-10 • Jumpering not supported 8WA1 011-6EG20 Type 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 • Rated uninterrupted current 32/1 A 8WA1 011-6EG20 10 units • Rated uninterrupted current 32/1 A 8WA1 011-6EG21 10 units • Rated uninterrupted current 1 A 8WA1 011-6EG22 10 units • Rated uninterrupted current 32/1 A 8WA1 011-6EG23 10 units • Rated uninterrupted current 32/1 A 8WA1 011-6EG24 10 units 8WA1 817 50 units Accessories Section Page End plates, for two-tier terminals Accessories 9/22 * You can order this quantity or a multiple thereof. 9/21 8WA1 Screw Terminals 8WA two-tier terminals with electronic components Version Order No. MOQ* Terminals with red LED, terminal size 4 mm² • Rated uninterrupted current 32 A • Rated insulation voltage 24 V DC • Mounting width 6.5 mm • Terminal height 45 mm • Terminal length 64 mm • U AWG 18-10 Type 1 2 3 4 1 2 3 4 1 2 3 4 9 • Without diode for current limitation 8WA1 011-6EG25 10 units • With diode for current limitation 8WA1 011-6EG26 10 units 8WA1 817 50 units 8WA1 011-6EG44 10 units 8WA1 817 50 units 8WA1 817 50 units Accessories Section Page End plates, for two-tier terminals Accessories 9/22 Zener diode terminals, terminal size 4 mm² • Mounting width 6.5 mm • Terminal height 45 mm • Terminal length 64 mm • U AWG 18-10 • Let-through current 0.25 A • Avalanche voltage UZ = 2.4 V, ±5 % Accessories Section Page End plates, for two-tier terminals Accessories 9/22 Accessories End plates, for two-tier terminals 9/22 * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA diode and isolating terminals ■ Selection and ordering data Version Order No. MOQ* 8WA1 011-1EF20 5 units General details • Thermoplastic insulating body • Enclosed at both ends Note Section Page For labeling accessories, see ... Accessories 10/2 Terminal size 2.5 mm² Diode terminals, terminal size 2.5 mm² • Rated insulation voltage 250 V URRM • Mounting width 6 mm • Terminal height 26 mm • Terminal length 41 mm • Screw terminals at both ends with test options for Ø 2.3 mm test plug • Rated uninterrupted current 1 A • Peak blocking voltage 1000 V 8WA1 011-1EF20 2 Accessories Section Page • Test plugs • Barriers, for terminal size 1.5 to 4 mm² Accessories Accessories 9/23 9/23 8WA1 868 8WA1 820 10 units 50 units 8WA1 501 10 units 1 8WA1 011-1EF20 8WA1 501 Through-type terminals, terminal size 2.5 mm², with sectionalizing feature • Rated uninterrupted current 10 A • Rated insulation voltage 380 V AC, 450 V DC (with alternate outgoing soldering tags) - Open isolating distance 380 V AC, 450 V DC - For use of barriers up to 750 V AC, 900 V DC • Mounting width 6 mm • Terminal height 29 mm • Terminal length 41 mm • With 2 holes for Ø 2.3 mm test plug • With screw terminals at both ends 9 Note 8WA1 501 Through-type terminals with sectionalizing feature allow easy isolation of the current path without disconnection of conductors. The sockets of the terminal screws allow actions, such as the measuring of the loop resistance or connection of an ammeter to the circuit. The use of connection combs reduces the conductor cross-section by one level. Accessories Section Page • Test plugs, red • Barriers, for terminal size 1.5 to 4 mm² Accessories Accessories 9/23 9/23 8WA1 868 8WA1 820 10 units 50 units Test plugs Red 8WA1 868 10 units Barriers, for terminal size 1.5 to 4 mm² 8WA1 820 50 units Accessories 8WA1 868 8WA1 820 * You can order this quantity or a multiple thereof. 9/23 8WA1 Screw Terminals 8WA terminals for components ■ Selection and ordering data Version Order No. MOQ* General details • Terminals for components • Screw terminal at both ends for 2 conductors each • Plugs with PCB for components • Enclosed at both ends Note Section Page For labeling accessories, see ... Accessories 10/2 Terminal size 1.5 mm² Terminals for components, terminal size 1.5 mm² (enclosure only) • Rated uninterrupted current 6.3 A • Rated insulation voltage 500 V • Mounting width 10 mm • Terminal height 40 mm • Terminal length 57 mm • For self-fitting with components • To next terminal, determined internally through customer's components 8WA1 011-1EE00 5/50 units Plugs for components, terminal size 1.5 mm² • Rated uninterrupted current 6.3 A • Rated insulation voltage 500 V • Mounting width 10 mm • Plug height 29 mm • Plug length 41 mm • With PCB and inscription label (20 mm × 9 mm) 8WA1 822-7EE00 1 unit 8WA1 011-1EE00 9 NSH0_00006 8WA1 822-7EE00 Plugs, fully equipped, example ■ Dimensional drawings 19 8 NSH00005 max. 4 18 10 max. 2 Space for components 9/24 * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA fuse terminals ■ Overview 8WA1 011-1SF12 fuse terminals are used to protect control circuits against short-circuits. The fuse links must be replaced at zero voltage. Finger safety is ensured in both closed and open positions. The fuse terminals are intended for 5 mm × 20 mm and 5 mm × 25 mm G fuse links up to 6.3 A and 250 V and for bridging links up to 16 A and 800 V and have a mounting for a replacement fuse link. The LED indicates the status of the disconnected fuse (residual current from 2 mA to 5 mA), but not if the plug is removed (floating). The fuse terminals are suitable for fuse links, sizes ¼" 1", ¼" 11/4" (6.3 mm × 32 mm) to 6.3 A and 250 V. Fuse terminals are positive opening fuse-disconnectors. The double connection is designed so that two conductors with different cross-sections can also be securely connected. The fixing base of the G fuse terminal allows both centered and recessed mounting, allowing the unhindered routing of a 6 mm × 6 mm N-busbar. The G fuse terminal can therefore be joined into a single group with the other terminals of a branch. ■ Selection and ordering data Version Order No. MOQ* General details • With thermoplastic insulating body • Screw terminal at both ends for 2 conductors each • Enclosed at both ends Note Section Page For labeling accessories, see ... Accessories 10/2 9 Terminal size 1.5 mm² 8WA1 011-1SF12 Fuse terminals, terminal size 1.5 mm² • Rated uninterrupted current 6.3 A when using fuses • Rated uninterrupted current 16 A when using the bridging link • Rated uninterrupted voltage 250 V when using fuses • Rated insulation voltage 800 V when using the bridging link • Mounting width 10 mm • Terminal height 42 mm • Terminal length 57 mm • Open isolating distance 500 V • U AWG 18-14 • s AWG 18-14 Versions • For G-fuse - Without LED - With LED 24 V AC/DC - With LED 48 V AC/DC - With LED 230 V AC/DC • For inch fuse - Without LED - With LED 24 V AC/DC - With LED, 120 V AC/110 V DC 8WA1 011-1SF12 8WA1 011-1SF13 8WA1 011-1SF14 8WA1 011-1SF15 10 units 10 units 10 units 10 units 8WA1 011-1SF30 8WA1 011-1SF31 8WA1 011-1SF32 10 units 10 units 10 units 8WA1 822-7EF16 8WA1 822-7EF18 8WA1 822-7EF21 10/200 units 10 units 10 units - Rated uninterrupted current 4 A - Rated uninterrupted current 6.3 A 8WA1 822-7EF23 8WA1 822-7EF25 10 units 10 units • Slow-response, low breaking capacity - Rated uninterrupted current 1 A - Rated uninterrupted current 1.6 A - Rated uninterrupted current 2.5 A 8WA1 822-7EF76 8WA1 822-7EF78 8WA1 822-7EF81 10 units 10 units 10 units - Rated uninterrupted current 4 A - Rated uninterrupted current 6.3 A 8WA1 822-7EF83 8WA1 822-7EF85 10 units 10 units 8WA1 891 10 units 8WA1 011-1SF13 Accessories G fuse links DIN 41660 8WA1 822-7EF16 Versions • Quick-response, high breaking capacity - Rated uninterrupted current 1 A - Rated uninterrupted current 1.6 A - Rated uninterrupted current 2.5 A 8WA1 891 Bridging links 5 mm × 25 mm * You can order this quantity or a multiple thereof. 9/25 8WA1 Screw Terminals 8WA through-type terminals with soldered and plug-in connection ■ Selection and ordering data Version Order No. MOQ* 8WA1 221 50 units 8WA1 810 8WA1 860 8WA1 820 50 units 50 units 50 units 8WA1 232 50 units General details • With thermoplastic insulating body • Enclosed at both ends Note Section Page For labeling accessories, see ... Accessories 10/2 Terminal size 1.5 mm² 8WA1 221 Through-type terminals, terminal size 1.5 mm² • Beige • Rated uninterrupted current 18 A • Rated insulation voltage 380 V AC, 450 V DC with alternately arranged terminals; when using barriers up to 800 V • Mounting width 5.5 mm • Terminal height 26 mm • Terminal length 41 mm • Soldered connection at both ends Accessories Section Page • Covers - With lightning symbol - White, facility for inscription • Barriers, for terminal size 1.5 to 4 mm² Accessories Accessories Accessories 9/26 9/26 9/26 Terminal size 6 mm² Through-type terminals, terminal size 6 mm², with plug-in terminal • Beige • Rated uninterrupted current 16 A per clamping point • Rated insulation voltage 400 V, when using barriers up to 1000 V • Mounting width 8 mm • Flat connection at both ends • Four flat-type connections 6.3 ... 0.8 mm 9 Accessories 8WA1 232 • Covers - With lightning symbol - White, facility for inscription • Connection bars - For two terminals - For ten terminals • Barriers, for terminal size 6 to 16 mm² Section Page Accessories Accessories 9/26 9/26 8WA1 811 8WA1 862 50 units 50 units Accessories Accessories Accessories 9/26 9/26 9/26 8WA1 822-7VH12 8WA1 822-7VH20 8WA1 821 50 units 10 units 50 units 8WA1 810 8WA1 811 50 units 50 units 8WA1 860 8WA1 862 50 units 50 units 8WA1 822-7VH12 8WA1 822-7VH20 50 units 10 units 8WA1 820 8WA1 821 50 units 50 units 8WA1 232 Accessories Covers Versions 8WA1 811 • With lightning symbol - For terminal size 1 ... 2.5 mm² - For terminal size 6 mm² • White, facility for inscription - For terminal size 1 ... 2.5 mm² - For terminal size 6 mm² Connection bars, for through-type terminal, terminal size 6 mm², with plug-in connection Versions 8WA1 822-7VH12 • For two terminals • For ten terminals Barriers Versions • For terminal size 1.5 ... 4 mm² • For terminal size 6 ... 16 mm² 8WA1 821 9/26 * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA measuring transformer terminals ■ Overview Measuring transformer terminals can be used for testing and isolating circuits in switchboards, control rooms, etc. without interrupting operation. On the other hand, it is also possible to use instrument isolating terminals for this purpose so that the terminal versions are all the same. The isolating and instrument isolating terminals contain an isolating device in the through-type connection. The isolating device permits electrical separation between the input and output of a terminal. Instrument set for three transformers with neutral point The instrument set with a neutral point is an extension of the previous circuit. Four instead of six lines are sufficient for connecting it with the measuring devices. The neutral point is produced on the measuring instruments on the one hand, and using a shortened 8WA1 822-7VH10 connection bar on the other. The instrument isolating terminal 1 is connected to the neutral point using a connecting comb. Test sockets for plugs with a diameter of 4 mm can be screwed into the front side of the through-type and isolating terminals. The rated insulation voltage between colored test sockets is 125 V. The rated insulation voltage between test sockets and connection bars not connected to the terminal is 16 V (circuit 3, terminals 3 and 5). Note The introduction of the 8WA1 011-1MH10 through-type terminals and their associated disconnecting links has made it considerably easier to configure terminal sets for current transformers. Instead of the 12 isolating or instrument isolating terminals used previously, now only 4 instrument isolating terminals and 3 through-type terminals are required. Two adjacent terminals can be connected in parallel with the disconnecting link. The disconnecting link can be operated in any position of the isolating device. Instrument set for one transformer The instrument set for one transformer makes the basic circuit of the transformer terminal blocks clear. This basic circuit is also included in much larger instrument sets, which is extended by adding on equivalent circuits. Links between the basic circuits provide many kinds of testing facilities, parallel outgoing lines to other measuring devices, connection of test equipment, etc. Instrument set with test facility This instrument set represents a significant enhancement over previous types. In normal operation, terminals 2, 5 and 8 are closed. For testing a measuring instrument (e.g. a plotter), these terminals are opened and terminals 3, 6 and 9 are closed in order to feed in a test signal. The transformers first have to be short-circuited with the disconnecting links between terminals 1-2, 4-5 and 7-8. Wire jumpers connect terminals 1, 4 and 7 with the neutral point. It is formed in terminals 10, 11, 12 and 13 with an 8WA1 887 connection bar. Instrument set for three transformers The simplest version of an instrument set for a three-phase circuit consists of three basic circuits strung together without any continuing links or extensions. Instead of isolating terminals 1, 3 and 5, less expensive through-type terminals can also be used. 1 2 1 2 3 4 5 6 1 2 3 4 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 10 11 12 13 1 Instrument set for 1 transformer 2 Instrument set for 3 transformers 3 Instrument set for 3 transformers with neutral point 4 Instrument set with testing facility Type k l k l k l k l N k l k l k l l l l 1 N Test L L1 L2 L3 L1 L2 L3 L1 L2 L3 I201_14021 Test socket Connection bar Small partition Disconnecting link (closed) Connecting comb, 2-pole Number required for 8WA1 011-1MH10 8WA1 011-1MH11 8WA1 011-1MH15 1 1 8WA1 825 a) 8WA1 885 8WA1 887 8WA1 822-7VH10 8WA1 822-7VH01 8WA1 822-7PH00 8WA1 822-7VH22 1 2 3 4 3 7 3 3 3 3 4 2 2 3 1 b) 3 1 3 1 3 4 a) In some cases additionally required between instrument sets b) Shortened Connection option for measuring transformer terminals (instrument sets) 9/27 9 8WA1 Screw Terminals 8WA measuring transformer terminals ■ Selection and ordering data Version Order No. MOQ* General details • With thermoplastic insulating body • Screw terminals at both ends and two holes for test sockets for Ø 4 mm test plug, insulated at both ends • Enclosed at both ends Note Section Page For labeling accessories, see ... Accessories 10/2 Terminal size 6 mm² 8WA1 011-1MH10 Typical circuit diagram 9 NSH0_00026 8WA1 011-1MH10 Through-type terminals, terminal size 6 mm² • Rated uninterrupted current 41 A • Rated insulation voltage 500 V • Mounting width 8 mm • Terminal height 33 mm • Terminal length 83 mm • Without test sockets • U AWG 14-8 • s AWG 16-10 20 units Accessories Section Page • Covers, for connection bars - Transparent - White, facility for inscription Accessories Accessories 9/30 9/30 8WA1 822-7AX01 8WA1 822-7AX03 10 units 10 units Accessories 9/30 8WA1 822-7PH00 50 units Accessories Accessories Accessories 9/30 9/30 9/30 8WA1 822-7PH03 8WA1 822-7PH06 8WA1 822-7PH08 50 units 50 units 50 units • Test plugs Accessories 9/30 8WA1 868 10 units • Disconnecting links Accessories 9/30 8WA1 822-7VH01 50 units • Insulation plates, for terminal size 2.5 to 6 mm² Accessories 9/30 8WA1 825 50 units 9/31 8WA7 163 10 units 9/31 8WA1 822-7VH22 10 units Accessories Accessories Accessories Accessories Accessories 9/31 9/31 9/31 9/31 9/31 8WA1 885 8WA1 886 8WA1 887 8WA1 888 8WA1 822-7VH10 50 units 50 units 20 units 10 units 50 units • Barriers, for Insta terminals, terminal size 2.5 mm² Accessories and measuring transformer terminals, terminal size 6 mm² 9/31 8WA1 822-7TH00 50 units • Test sockets - Rated voltage between test socket and bypassed connection bar: 16 V, recessed - Rated voltage between two test sockets: 125 V Y Green Y Black Y Red • Connection combs - 10-pole for measuring transformer terminals, can Accessories be shortened as required - 2-pole Accessories • Connection bars, for terminal size 6 mm² - Two terminals - Three terminals - Four terminals - Ten terminals - Unmounted for ten terminals 9/28 8WA1 011-1MH10 * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA measuring transformer terminals 8WA1 011-1MH11 Typical circuit diagram NSH0_00027 8WA1 011-1MH11 Version Order No. MOQ* Isolating terminals, terminal size 6 mm² • Rated uninterrupted current 41 A • Rated insulation voltage 500 V • Mounting width 8 mm • Terminal height 33 mm • Terminal length 83 mm • Without test sockets • U AWG 14-8 • s AWG 16-10 8WA1 011-1MH11 20 units Accessories Section Page • Covers, for connection bars - Transparent - White, facility for inscription Accessories Accessories 9/30 9/30 8WA1 822-7AX01 8WA1 822-7AX03 10 units 10 units Accessories 9/30 8WA1 822-7PH00 50 units Accessories Accessories Accessories 9/30 9/30 9/30 8WA1 822-7PH03 8WA1 822-7PH06 8WA1 822-7PH08 50 units 50 units 50 units • Test plugs Accessories 9/30 8WA1 868 10 units • Disconnecting links Accessories 9/30 8WA1 822-7VH01 50 units • Insulation plates, for terminal size 2.5 to 6 mm² Accessories 9/30 8WA1 825 50 units 9/31 8WA7 163 10 units 9/31 8WA1 822-7VH22 10 units Accessories Accessories Accessories 9/31 9/31 9/31 8WA1 885 8WA1 886 8WA1 887 50 units 50 units 20 units Accessories Accessories 9/31 9/31 8WA1 888 8WA1 822-7VH10 10 units 50 units • Barriers, for Insta terminals, terminal size 2.5 mm² Accessories and measuring transformer terminals, terminal size 6 mm² 9/31 8WA1 822-7TH00 50 units • Test sockets - Rated voltage between test socket and bypassed connection bar: 16 V, recessed - Rated voltage between two test sockets: 125 V Y Green Y Black Y Red • Connection combs - 10-pole for measuring transformer terminals, can Accessories be shortened as required - 2-pole Accessories • Connection bars, for terminal size 6 mm² - Two terminals - Three terminals - Four terminals - Ten terminals - Unmounted for ten terminals * You can order this quantity or a multiple thereof. 9/29 9 8WA1 Screw Terminals 8WA measuring transformer terminals 8WA1 011-1MH15 Typical circuit diagram NSH0_00028 8WA1 011-1MH15 Version Order No. Instrument isolating terminals, terminal size 6 mm² • Mounting width 8 mm • Terminal height 33 mm • Terminal length 83 mm • Open isolating distance • With recessed test sockets • U AWG 14-8 • s AWG 16-10 8WA1 011-1MH15 20 units Accessories Section Page • Covers, for connection bars - Transparent - White, facility for inscription Accessories Accessories 9/30 9/30 8WA1 822-7AX01 8WA1 822-7AX03 10 units 10 units Accessories 9/30 8WA1 822-7PH00 50 units Accessories Accessories Accessories 9/30 9/30 9/30 8WA1 822-7PH03 8WA1 822-7PH06 8WA1 822-7PH08 50 units 50 units 50 units • Test plugs Accessories 9/30 8WA1 868 10 units • Disconnecting links Accessories 9/30 8WA1 822-7VH01 50 units • Insulation plates, for terminal size 2.5 to 6 mm² Accessories 9/30 8WA1 825 50 units 9/31 8WA7 163 10 units 9/31 8WA1 822-7VH22 10 units Accessories Accessories Accessories 9/31 9/31 9/31 8WA1 885 8WA1 886 8WA1 887 50 units 50 units 20 units Accessories Accessories 9/31 9/31 8WA1 888 8WA1 822-7VH10 10 units 50 units • Barriers, for Insta terminals, terminal size 2.5 mm² Accessories and measuring transformer terminals, terminal size 6 mm² 9/31 8WA1 822-7TH00 50 units 8WA1 822-7AX01 8WA1 822-7AX03 10 units 10 units 8WA1 822-7PH00 50 units 8WA1 822-7PH03 8WA1 822-7PH06 8WA1 822-7PH08 50 units 50 units 50 units Test plugs Red 8WA1 868 10 units Disconnecting links Rated insulation voltage with disconnecting link open according to DIN VDE 0110: 125 V Gr. C or 250 V Gr. B 8WA1 822-7VH01 50 units Insulation plates, for terminal size 2.5 to 6 mm² 8WA1 825 50 units • Test sockets - Rated voltage between test socket and bypassed connection bar: 16 V, recessed - Rated voltage between two test sockets: 125 V Y Green Y Black Y Red • Connection combs - 10-pole for measuring transformer terminals, can Accessories be shortened as required - 2-pole Accessories 9 MOQ* • Connection bars, for terminal size 6 mm² - Two terminals - Three terminals - Four terminals - Ten terminals - Unmounted for ten terminals Accessories Covers, for connection bars For through-type terminals, size 2.5 to 6 mm² Versions • Transparent • White, facility for inscription Test sockets Ø 4 mm Versions • Rated voltage between test socket and bypassed connection bar: 16 V, recessed 8WA1 822-7PH00 • Rated voltage between two test sockets: 125 V - Green - Black - Red 8WA1 822-7PH03 8WA1 868 8WA1 822-7VH01 8WA1 825 9/30 * You can order this quantity or a multiple thereof. 8WA1 Screw Terminals 8WA measuring transformer terminals Version Order No. MOQ* 8WA7 163 10 units 8WA1 822-7VH22 10 units 8WA1 885 8WA1 886 8WA1 887 8WA1 888 8WA1 822-7VH10 50 units 50 units 20 units 10 units 50 units 8WA1 822-7TH00 50 units Connection combs For inserting in the clamping points Versions 8WA7 163 • 10-pole for measuring transformer terminals, can be shortened as required • 2-pole Connection bars, for terminal size 6 mm² Versions 8WA1 885 • • • • • Two terminals Three terminals Four terminals Ten terminals Unmounted for ten terminals Barriers, for Insta terminals, terminal size 2.5 mm² and measuring transformer terminals, terminal size 6 mm² 8WA1 822-7TH00 9 * You can order this quantity or a multiple thereof. 9/31 8WA1 Screw Terminals 8WA transformer terminals ■ Overview The 8WA9 200 terminals are used for transformers and rectifiers. I201_14022 The terminals are insulated at both ends and are finger-safe to DIN VDE 0106 Part 100. The normal labeling accessories can be used to label the transformer terminals. In addition to the screw connection, the 8WA9 terminals have a 6.3-0.8 flat connector. The soldered connection is protected by a hinged cover following soldering on of the conductor. 3 2 1 1 Retainer for 2 mm x 10 mm mounting rail 2 Soldered connection 3 Hinged cover ■ Selection and ordering data Version Order No. MOQ* Transformer terminals, terminal size 4 mm² • Enclosed at both ends • Beige • Rated uninterrupted current 24 A • Rated insulation voltage acc. to DIN VDE 0110, Group C 690 V, 600 V to u, 600 V to s Group D • Mounting width 7.5 mm • Terminal height 34 mm • Terminal length 27 mm • With insulating body • Made of molded thermoplastic • For 2 mm × 10 mm mounting rail • Screw terminal: - Solid 0.5 mm² up to 6 mm² - Finely stranded with or without end sleeve 0.5 mm² to 4 mm² - Stripped length 10 mm • Flat connector: 6.3-0.8 • Soldered connection: - Solid up to Ø 3 mm - Finely stranded up to 2.5 mm² - Stripped length 7 mm - s18-10 AWG, U18-10 AWG 8WA9 200 100 units 8WA8 848-2AY 8WA8 847-0XA 100 units 100 units 8WA8 848-2AY 8WA8 847-0XA 100 units 100 units Terminal size 4 mm² 9 8WA9 200 (side view) 8WA9 200 (plan view) Accessories Section Page • Labeling strips - Blank - Any inscription Accessories Accessories 9/32 9/32 Accessories Labeling strips Versions • Blank • Any inscription 9/32 * You can order this quantity or a multiple thereof.