P R O D U C T B R I E F The BTS 716G is a four channel high-side power switch (four times 140 mΩ) in P-DSO-20 package. It is fully protected by embedded protection functions. There are two diagnostic feedback pins signalling open load and over temperature. The device is built by two chips, monolithically integrated in Smart SIPMOS technology. The power transistor is built by a N-channel vertical power MOSFET with charge pump. The inputs are ground referenced CMOS compatible. Basic Functions Protective Functions BTS 716G Diagnostic Functions ■ Very low standby current ■ Short circuit protection ■ CMOS compatible input ■ Overload protection ■ Improved electromagnetic ■ Current limitation ■ Open load detection in OFF-state compatibility (EMC) ■ Thermal shutdown ■ Feedback of thermal shutdown in Fast demagnetization of inductive ■ Overvoltage protection (including ■ loads ■ Stable behaviour at undervoltage ■ Wide operating voltage range ■ Logic ground independent from ■ Diagnostic feedback with open drain output ON-state load dump) with external resistor ■ ■ load ground ■ Reverse battery protection with Applications external resistor ■ µC compatible high-side power Loss of ground and loss of Vbb switch with diagnostic feedback protection for 12 V and 24 V grounded loads Electrostatic discharge protection ■ (ESD) All types of resistive, inductive and capacitive loads ■ Most suitable for loads with high inrush currents, so as lamps ■ Replaces electromechanical relays, fuses and discrete circuits Smart High-Side Power Switch Four Channels 140 mΩ N e v e r s t o p t h i n k i n g . P R O D U C T B R I E F Block Diagram GND Channel 1, 2 Vbb Current Limitation Gate Control & Charge Pump Internal Power Supply IN2 Logic IN1 ESD Protection Clamp for Inductive Load Temperature Sensor OUT1 Open Load Detection ST1, 2 OUT2 Reverse Battery Protection Channel 3, 4 IN3 IN4 ST3, 4 Control and Protection Circuit Equivalent to Channel 1, 2 OUT3 OUT4 Product Summary Type Sales Code Package BTS 716G Q67060-S7025 P-DSO-20 Parameter Symbol Operating Voltage Vbb(ON) Values 5.5 ... 40 V Active Channels RON(max) IL(nom) IL(SCr) On-state Resistance Nominal Load Current Current Limitation One Two Four 140 mΩ 70 mΩ 35 mΩ 2.4 A 3.7 A 5.7 A 6.5 A Application Example Vbb Lamp 10 W GND OUT1 OUT2 Relay Lamp 10 W OUT3 BTS 716G IN1 ST1, 2 IN2 OUT4 IN3 ST3, 4 IN4 Valve µC How to reach us: http://www.infineon.com Published by Infineon Technologies AG, St.-Martin-Strasse 53, D-81669 München © Infineon Technologies AG 2003. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office. Template: pb_tmplt.fm/2/2003-05-01 Published by Infineon Technologies AG Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in lifesupport devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Ordering No. B152-H8245-X-X-7600 Printed in Germany PS 06031.5 NB