MIC5156/5157/5158 Micrel, Inc. MIC5156/5157/5158 Super LDO™ Regulator Controller General Description either 3.3V, 5.0V, or 12V. The MIC5158 can be configured as a fixed 5V controller or programmed to any voltage from 1.3V to 36V using two external resistors. The MIC5156 is available in an 8-pin DIP or SOIC. The MIC5157 and MIC5158 are available in a 14-pin DIP or SOIC which operate from –40°C to +85°C. The MIC5156, MIC5157, and MIC5158 Super Low-Dropout (LDO) Regulator Controllers are single IC solutions for highcurrent low-dropout linear voltage regulation. Super LDO™ Regulators have the advantages of an external N-channel power MOSFET as the linear pass element. The MIC5156/7/8 family features a dropout voltage as low as the RDS(ON) of the external power MOSFET multiplied by the output current. The output current can be as high as the largest MOSFETs can provide. The MIC5156/7/8 family operates from 3V to 36V. The MIC5156 requires an external gate drive supply to provide the higher voltage needed to drive the gate of the external MOSFET. The MIC5157 and MIC5158 each have an internal charge pump tripler to produce the gate drive voltage. The tripler is capable of providing enough voltage to drive a logic-level MOSFET to 3.3V output from a 3.5V supply and is clamped to 17.5V above the supply voltage. The tripler requires three external capacitors. The regulator output is constant-current limited when the controller detects 35mV across an optional external sense resistor. An active-low open-collector flag indicates a low voltage of 8% or more below nominal output. A shutdown (low) signal to the TTL-compatible enable control reduces controller supply current to less than 1µA while forcing the output voltage to ground. The MIC5156-3.3 and MIC5156-5.0 controllers have internally fixed output voltages. The MIC5156 [adjustable] output is configured using two external resistors. The MIC5157 is a fixed output controller which is externally configured to select Features • • • • • • • • • • • • • 4.5mA typical operating current <1µA typical standby current Low external parts count Optional current limit (35mV typical threshold) 1% initial output voltage tolerance in most configurations 2% output voltage tolerance over temperature Fixed output voltages of 3.3V, 5.0V (MIC5156) Fixed output voltages of 3.3V, 5.0V, 12V (MIC5157) Programmable (1.3 to 36V) with 2 resistors (MIC5156/8) Internal charge pump voltage tripler (MIC5157/8) Enable pin to activate or shutdown the regulator Internal gate-to-source protective clamp All versions available in DIP and SOIC Applications • • • • • Ultrahigh current ultralow dropout voltage regulator Constant high-current source Low parts count 5.0V to 3.3V computer supply Low noise/low-dropout SMPS post regulator High-current, current-limited switch Typical Applications +12V VIN 5V 3mΩ 47µF RS RS = 0.035V /I LIMIT SMP60N03-10L 8 0.1µF VOU T 3.3V, 10A VIN (3.61Vmin.) CL* 47µF *Improves transient response to load changes 9 10 3mΩ RS 1 5 2 11 12 13 E S D VD 8 C – S 7 C G D VD 6 3 MIC5157 MIC5156-3.3 5 4 3 5 F 6 G C E 7 G F 1 VC 2 C 3 VP 4 1.0µF 0.1µF Enable Shutdown G 0.1µF 14 Enable Shutdown VOU T 3.3V, 10A CL* 47µF RS = 0.035V /I LIMIT *Improves transient IRLZ44 (Logic Level MOSFET) response to load changes 47µF 10A Low-Dropout Voltage Regulator 10A 5V to 3.3V Desktop Computer Regulator Super LDO is a trademark of Micrel, Inc. Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com August 2005 1 MIC5156/5157/5158 MIC5156/5157/5158 Micrel, Inc. Ordering Information MIC5156 Part Number Temperature Standard Pb-Free Voltage Range Package MIC5156-3.3BN MIC5156-3.3YN 3.3V –40°C to +85°C 8-pin DIP MIC5156-5.0BN MIC5156-5.0YN 5.0V –40°C to +85°C 8-pin DIP MIC5156BN MIC5156YN Adj –40°C to +85°C 8-pin DIP MIC5156-3.3BM MIC5156-3.3YM 3.3V –40°C to +85°C 8-pin SOIC MIC5156-5.0BM MIC5156-5.0YM 5.0V –40°C to +85°C 8-pin SOIC MIC5156BM MIC5156YM Adj –40°C to +85°C 8-pin SOIC Ordering Information MIC5157 Part Number Temperature Standard Pb-Free Voltage Range Package MIC5157BN MIC5157YN Selectable –40°C to +85°C 14-pin DIP MIC5157BM MIC5157YM Selectable –40°C to +85°C 14-pin SOIC Ordering Information MIC5158 Part Number Temperature Standard Pb-Free Voltage Range Package MIC5158BN MIC5158YN 5.0V/Adj –40°C to +85°C 14-pin DIP MIC5158BM MIC5158YM 5.0V/Adj –40°C to +85°C 14-pin SOIC Pin Configuration MIC5156 MIC5156-x.x EN 1 8 EA EN 1 8 S (Source) FLAG 2 7 D (Drain) FLAG 2 7 D (Drain) GND 3 6 G (Gate) GND 3 6 G (Gate) VP 4 VP 4 5 VD D MIC5157 5V 1 3.3V 2 5 VD D MIC5158 EA 1 14 E N 14 E N 13 S (Source) 5V FB 2 13 S (Source) FLAG 3 12 D (Drain) FLAG 3 12 D (Drain) GND 4 11 G (Gate) GND 4 11 G (Gate) MIC5156/5157/5158 VC P 5 10 VD D VC P 5 10 VD D C2– 6 9 C1– C2– 6 9 C1– C2+ 7 8 C1+ C2+ 7 8 C1+ 2 August 2005 MIC5156/5157/5158 Micrel, Inc. Pin Description MIC5156 Pin Number Pin Name 1 EN Pin Function 2 FLAG Output Flag (Output): Open collector output is active (low) when VOUT is more than 8% below nominal output. Circuit has 3% hysteresis. 3 GND Circuit ground. 4 VP N-channel Gate Drive Supply Voltage: User supplied voltage for driving the gate of the external MOSFET. 5 VDD Supply Voltage (Input): Supply voltage connection. Connect sense resistor (RS) to VDD if current limiting used. Connect supply bypass capacitor to ground near device. 6 G Gate (Output): Drives the gate of the external MOSFET. 7 D Drain and Current Limit (Input): Connect to external MOSFET drain and external sense resistor (current limit), or connect to VDD and external MOSFET drain (no current limit). 8 (3.3V, 5V) S Source (Input): Top of internal resistive divider chain. Connect directly to the load for best load regulation. 8 (adjustable) EA Enable (Input): TTL high enables regulator; TTL low shuts down regulator. Error Amplifier (Input): Connect to external resistive divider. Pin Description MIC5157, MIC5158 Pin Number Pin Name 1 (MIC5157) 5V 5V Configuration (Input): Connect to S (source) pin for 5V output. Pin Function 1 (MIC5158) EA Error Amplifier (Input): Connect to external resistive divider to obtain adjustable output. 2 (MIC5157) 3.3V 3.3V Configuration (Input): Connect to S (source) pin for 3.3V output. 2 (MIC5158) 5V FB 5V Feedback (Input): Connect to EA for fixed 5V output. 3 FLAG Output Voltage Flag (Output): Open collector is active (low) when VOUT is 8% or more below its nominal value. 4 GND Circuit ground. VCP Voltage Tripler Output [Filter Capacitor]. Connect a 1 to 10µF capacitor to ground. 6 C2– Charge Pump Capacitor 2: Second stage of internal voltage tripler. Connect a 0.1µF capacitor from C2+ to C2–. 7 C2+ Charge Pump Capacitor 2: See C2– pin 6. 8 C1+ Charge Pump Capacitor 1: First stage of internal voltage tripler. Connect a 0.1µF capacitor from C1+ to C1–. 9 C1– Charge Pump Capacitor 1: See C1+ pin 8. 10 VDD Supply Voltage (Input): Supply voltage connection. Connect sense resistor (RS) to VDD if current limiting used. Connect supply bypass capacitor to ground near device. 5 11 G Gate (Output): Connect to External MOSFET gate. 12 D Drain and Current Limit (Input): Connect to external MOSFET drain and external sense resistor (current limit), or connect to VDD and external MOSFET drain (no current limit). 13 (MIC5157) S Source and 3.3V/5V Configuration: Top of internal resistor chain. Connect to source of external MOSFET for 3.3V, 5V, and 12V operation. Also see 3.3V and 5V pin descriptions. 13 (MIC5158) S Source (Input): Top of internal resistor chain. Connect to top of external resistive divider and source of external MOSFET. 14 EN August 2005 Enable (Input): TTL high enables regulator; TTL low shuts down regulator. 3 MIC5156/5157/5158 MIC5156/5157/5158 Micrel, Inc. Absolute Maximum Ratings (Note 1) Operating Ratings (Note 2) Supply Input (VDD)....................................................... +38V Enable Input (VEN) ..........................................–0.3V to 36V Gate Output (VG) MIC5156 ......................................... +55V Charge Pump Node (VCP) MIC5157/8 ........................ +55V Source Connection (VS) ................................... 1.3 to +36V Flag (VFLAG) .................................................... –0.3 to +40V Storage Temperature (TS) ........................ –65°C to +150°C Lead Temperature (soldering 10 sec.) ....................... 300°C Ambient Temperature Range (TA) MIC515xBM/BN ...................................... –40°C to +85°C Junction Temperature (TJ) ....................................... +150°C Thermal Resistance (θJA) Package MIC5156 MIC5157/8 DIP ................................ 100°C/W ..................... 90°C/W SOIC ............................. 160°C/W ................... 120°C/W Electrical Characteristics(Note 5) VDD = 5V, VEN = 5V; TA = 25°C; unless noted. Symbol Parameter VDD Supply Voltage IDD(ON) IDD(OFF) Supply Current MIC5157/8 IDD(ON) IDD(OFF) Supply Current MIC5156 VIH VIL Enable Input Threshold VCP Max. Charge Pump Voltage EN IB Enable Input Bias Current fCP Charge Pump Frequency VOUT MAX VOUT MIN VLIM VS VBG Maximum Gate Drive Voltage (MIC5157/8) Minimum Gate Drive Voltage Current Limit Threshold Source Voltage Condition Min Operating, VEN = 5V Shutdown, VEN = 0V Operating, VEN = 5V Shutdown, VEN = 0V High Low VEN = 2.4V 5 9 24 VDD – VD @ ILIM 28 Short G (gate) to (S) source, Note 4 MIC5156-3.3 MIC5156-5.0 MIC5157, 3.3V pin to S pin (3.3V config.) MIC5157, 5V pin to S pin (5V config.) MIC5157, VDD = 7V, (12V config.) MIC5158, 5V FB pin to EA pin (5V config.) VSOURCE > VOUT(NOM) Bandgap Reference Voltage MIC5156 [adjustable] and MIC5158 5V < VDD < 15V, VOUT = 3.3V VFT Flag Comparator Threshold VSAT Flag Comparator Sat. Voltage VFH Flag Comparator Hysteresis % of nominal VSOURCE % of nominal VSOURCE IFLAG = 1mA Note 1. Exceeding the absolute maximum rating may damage the device. Note 2. The device is not guaranteed to function outside its operating rating. Note 3. Devices are ESD sensitive. Handling precautions recommended. Note 4. Test configuration. External MOSFET not used. Note 5. Specification for packaged product only. MIC5156/5157/5158 Max Units 36 V 2.7 0.1 10 5 mA µA 4.5 0.1 10 5 mA µA 1.3 1.3 0.8 V V 20 25 µA 17.5 18.5 V 160 VSOURCE = 0V VDD = 3.5V VDD = 5V VDD = 12V Output Voltage Line Regulation Gate to Source Clamp 2.4 VCP – VDD, VDD > 10V VLR VGS MAX Typ 3 4 7.0 11.3 28 kHz 9 15 30 V V V 35 42 mV 3.267 4.950 3.250 4.950 11.70 4.925 3.3 5.0 3.3 5.0 12 5.0 3.333 5.050 3.350 5.050 12.30 5.075 V V V V V V 1.222 1.235 1.248 V 2 7 mV 16.6 20 1.0 14 V 92 3 0.09 V % % 0.2 V August 2005 MIC5156/5157/5158 Micrel, Inc. Typical Characteristics 3.3V Regulator Output Voltage vs. Temperature 3.29 3.28 3.27 ON-STATE SUPPLY CURRENT (mA) 3.26 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) MIC5157/8 On-State Supply Current vs. Supply Voltage 10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 0 10 15 20 25 5 SUPPLY VOLTAGE (V) 30 5.02 5.01 5.00 4.99 4.98 4.96 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) 60 FLAG VOLTAGE (mV) 50 40 30 20 10 0 1.8 0 10 15 20 25 5 SUPPLY VOLTAGE (V) Enable Threshold Voltage vs. Temperature 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) August 2005 4.5 4.0 3.5 3.0 2.5 VDD = 5V 2.0 1.5 1.0 0.5 0.0 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) VDD = 5V IF LAG = 1mA 175 150 125 100 75 50 25 120 Enable Input Bias Current vs. Enable Voltage 100 80 60 40 20 0 6 4 LOGIC INPUT 2 3.3V OUTPUT -2 -0.2 Flag Output Voltage vs. Temperature 0 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) 30 1.6 MIC5157/8 On-State Supply Current vs. Temperature 200 ENABLE BIAS CURRENT (µA) ENABLE THRESHOLD VOLTAGE (V) CHARGE PUMP VOLTAGE (V) Charge-Pump Output Voltage vs. Supply Voltage 5.0 8 0 4.97 OFF-STATE SUPPLY CURRENT (µA) 3.30 MOSFET = IRF540 VIN = 5V, IL = 0.5A CC 1 = CC 2 = 0.1µF CC P = 1µF CL = 50µF 10 0 2 4 6 8 10 12 14 16 ENABLE VOLTAGE (V) 5 5.0 0.0 0.2 0.4 TIME (ms) 0.6 Off-State Supply Current vs. Temperature VDD = 5V 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) Flag Output Voltage vs. Flag Current 1.0 VDD = 5V 0.9 FLAG VOLTAGE (V) 3.31 5.03 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 CURRENT LIMIT THRESHOLD (mV) 3.32 MIC5157/8 Turn-On Response Time for 3.3V 12 VOLTAGE (V) OUTPUT VOLTAGE (V) 3.33 5.0V Regulator Output Voltage vs. Temperature 5.04 ON-STATE SUPPLY CURRENT (mA) OUTPUT VOLTAGE (V) 3.34 70 0 10 2 4 6 8 FLAG SINK CURRENT (mA) Current Limit Threshold vs. Temperature 60 50 40 30 20 10 0 -60 -30 0 30 60 90 120 150 TEMPERATURE (°C) MIC5156/5157/5158 MIC5156/5157/5158 Micrel, Inc. Block Diagram MIC5156 +12V Input 0.1µF +5V Input VP VDD Internal Bias EN Enable Shutdown RS 3mΩ 12k to all internal blocks 1.235V Bandgap Reference ILIMIT Comparator +5V Input 35mV Q2 Switched 5V Load VOU T Comparator FLAG G (Gate) Error Amp 16.6V 75mV * fixed version only † 3.3V = 17k, 5V = 32k ‡ D (Drain) [ ILIMIT ] Q1 SMP60N03-10L S* (Source) Regulated +3.3V Output 17k† 10k GND CL E A‡ adjustable version only Block Diagram with External Components Fixed 3.3V Power Supply with 5.0V Load Switch Block Diagram MIC5157 +5V Input 0.1µF C1+ Oscillator C1 0.1µF C3 1µF C2 C2– VC P C1– C2+ VDD VC P Clamp Charge Pump Tripler VOU T Comparator EN Enable Shutdown RS 3mΩ to all nternal i blocks ILIMIT Comparator D (Drain) [ ILIMIT ] 35mV 1.235V Bandgap Reference FLAG Internal Bias G (Gate) Error Amp 16.6V 75mV 58k 15k S (Source)* 5V Q1 IRFZ44 Regulated +3.3V Output CL 3.3V 17k 10k GND Block Diagram with External Components Fixed 3.3V 10A Power Supply MIC5156/5157/5158 6 August 2005 MIC5156/5157/5158 Micrel, Inc. Block Diagram MIC5158 +5V Input 0.1µF C1+ Oscillator C1 0.1µF C3 1µF C2 C2– VC P C1– C2+ VDD VC P Clamp Charge Pump Tripler Internal Bias ILIMIT Comparator 35mV FLAG Enable Shutdown RS 3mΩ to all internal blocks 1.235V Bandgap Reference VOU T Comparator EN D (Drain) [ ILIMIT ] G (Gate) Error Amp 16.6V 75mV 32k 10k Q1 IRFZ44 S (Source) Regulated +3.6V Output 5V FB CL GND EA 19.1k 10.0k Block Diagram with External Components Adjustable Power Supply, 3.6V Configuration Functional Description to-source enhancement voltage for an external N-channel MOSFET (regulator pass element) placed between the supply and the load. The gate-to-source voltage may vary from 1V to 16V depending upon the supply and load conditions. Because the source voltage (output) approaches the drain voltage (input) when the regulator is in dropout and the MOSFET is fully enhanced, an additional higher supply voltage is required to produce the necessary gate-to-source enhancement. This higher gate drive voltage is provided by an external gate drive supply (MIC5156) or by an internal charge pump (MIC5157 and MIC5158). Gate Drive Supply Voltage (MIC5156 only) A Super LDO Regulator is a complete regulator built around Micrel’s Super LDO Regulator Controller. Refer to Block Diagrams MIC5156, MIC5157, and MIC5158. Version Differences The MIC5156 requires an external voltage for MOSFET gate drive and is available in 3.3V fixed output, 5V fixed output, or adjustable output versions. With 8-pins, the MIC5156 is the smallest of the Super LDO Regulator Controllers. The MIC5157 and MIC5158 each have an internal charge pump which provides MOSFET gate drive voltage. The MIC5157 has a selectable fixed output of 3.3V, 5V, or 12V. The MIC5158 may be configured for a fixed 5V or adjustable output. Enable (EN) With at least 3.0V on VDD, applying a TTL low to EN places the controller in shutdown mode. A TTL high on EN enables the internal bias circuit which powers all internal circuitry. EN must be pulled high if unused. The voltage applied to EN may be as high as 36V. The controller draws less than 1µA in shutdown mode. Gate Enhancement The Super LDO Regulator Controller manages the gateAugust 2005 The gate drive supply voltage must not be more than 14V above the supply voltage (VP – VDD < 14V). The minimum necessary gate drive supply voltage is: VP = VOUT + VGS + 1 where: VP = gate drive supply voltage VOUT = regulator output voltage VGS = gate-to-source voltage for full MOSFET gate enhancement The error amplifier uses the gate drive supply voltage to drive the gate of the external MOSFET. The error amplifier output can swing to within 1V of VP. 7 MIC5156/5157/5158 MIC5156/5157/5158 Micrel, Inc. Note that the recovery time to repetitive load transients may be affected with small pump capacitors. Gate-to-Source Clamp A gate-to-source protective voltage clamp of 16.6V protects the MOSFET in the event that the output voltage is suddenly forced to zero volts. This prevents damage to the external MOSFET during shorted load conditions. Refer to “Charge Pump” for normal clamp circuit operation. The source connection required by the gate-to-source clamp is not available on the adjustable version of the MIC5156. Output Regulation At start-up, the error amplifier feedback voltage (EA), or internal feedback on fixed versions, is below nominal when compared to the internal 1.235V bandgap reference. This forces the error amplifier output high which turns on external MOSFET Q1. Once the output reaches regulation, the controller maintains constant output voltage under changing input and load conditions by adjusting the error amplifier output voltage (gate enhancement voltage) according to the feedback voltage. Out-of-Regulation Detection When the output voltage is 8% or more below nominal, the open-collector FLAG output (normally high) is forced low to signal a fault condition. The FLAG output can be used to signal or control external circuitry. The FLAG output can also be used to shut down the regulator using the EN control. Current Limiting Super LDO Regulators perform constant-current limiting (not foldback). To implement current limiting, a sense resistor (RS) must be placed in the “power” path between VDD and D (drain). If the voltage drop across the sense resistor reaches 35mV, the current limit comparator reduces the error amplifier output. The error amplifier output is decreased only enough to reduce the output current, keeping the voltage across the sense resistor from exceeding 35mV. Charge Pump (MIC5157/5158 only) The charge pump tripler creates a dc voltage across reservoir capacitor C3. External capacitors C1 and C2 provide the necessary storage for the stages of the charge pump tripler. The tripler’s approximate dc output voltage is: VCP ≈ 3 (VDD – 1) where: VCP = charge pump output voltage VDD = supply voltage The VCP clamp circuit limits the charge pump voltage to 16V above VDD by gating the charge pump oscillator ON or OFF as required. The charge pump oscillator operates at 160kHz. The error amplifier uses the charge pump voltage to drive the gate of the external MOSFET. It provides a constant load of about 1mA to the charge pump. The error amplifier output can swing to within 1V of VCP. Although the MIC5157/8 is designed to provide gate drive using its internal charge pump, an external gate drive supply voltage can be applied to VCP . When using an external gate drive supply, VCP must not be forced more than 14V higher than VDD. When constant loads are driven, the ON/OFF switching of the charge pump may be evident on the output waveform. This is caused by the charge pump switching ON and rapidly increasing the supply voltage to the error amplifier. The period of this small charge pump excitation is determined by a number of factors: the input voltage, the 1mA op-amp load, any dc leakage associated with the MOSFET gate circuit, the size of the charge pump capacitors, the size of the charge pump reservoir capacitor, and the characteristics of the input voltage and load. The period is lengthened by increasing the charge pump reservoir capacitor (C3). The amplitude is reduced by weakening the charge pump—this is accomplished by reducing the size of the pump capacitors (C1 and C2). If this small burst is a problem in the application, use a 10µF reservoir capacitor at C3 and 0.01µF pump capacitors at C1 and C2. Application Information VIN MOSFET Selection Standard N-channel enhancement-mode MOSFETs are acceptable for most Super LDO regulator applications. Logic-level N-channel enhancement-mode MOSFETs may be necessary if the external gate drive voltage is too low (MIC5156), or the input voltage is too low, to provide adequate charge pump voltage (MIC5157/8) to enhance a standard MOSFET. Circuit Layout For the best voltage regulation, place the source, ground, and error amplifier connections as close as possible to the load. See figures (1a) and (1b). MIC5156/5157/5158 G MIC515x S GND Figure 1a. Connections for Fixed Output 8 August 2005 MIC5156/5157/5158 Micrel, Inc. Adjustable Configurations VIN Micrel’s MIC5156 [adjustable] and MIC5158 require an external resistive divider to set the output voltage from 1.235V to 36V. For best results, use a 10kΩ resistor for R2. See equation (1) and figure (2). G MIC5157 S or MIC5158 GND EA 1) R 1 = 1 × 1 04 ( 1V. O2 U3 T5 MIC5157/8 VIN GND EA* R1 R2 10k Figure 2. Typical Resistive Divider EA Input Filter Capacitor The Super LDO requires an input bypass capacitor for accommodating wide changes in load current and for decoupling the error amplifier and charge pump. A medium to large value low-ESR (equivalent series resistance) capacitor is best, mounted close to the device. * Optional 16V zener diode recommended in applications where VG is greater than 18V Figure 1c. MIC5156 Connections for Adjustable Output Output Filter Capacitor An output filter capacitor may be used to reduce ripple and improve load regulation. Stable operation does not require a large capacitor, but for transient load regulation the size of the output capacitor may become a consideration. Common aluminum electrolytic capacitors perform nicely; very low-ESR capacitors are not necessary. Increased capacitance (rather than reduced ESR) is preferred. The capacitor value should be large enough to provide sufficient I = C × dV/dt current consistent with the required transient load regulation quality. For a given step increase in load current, the output voltage will drop by about dV = I × dt/C, where I represents the increase in load current over time t. This relationship assumes that all output current was being supplied via the MOSFET pass device prior to the load increase. Small (0.01µF to 10µF) film capacitors parallel to the load will further improve response to transient loads. Some linear regulators specify a minimum required output filter capacitance because the capacitor determines the dominant pole of the system, and thereby stabilizes the system. This is not the situation for the MIC5156/7/8; its dominant pole is determined within its error amplifier. MOSFET Gate-to-Source Protection When using the adjustable version of the MIC5156, an external 16V zener diode placed from gate-to-source is recommended for MOSFET protection. All other versions of the Super LDO regulator controller use the internal gate-to-source clamp. Output Voltage Configuration Fixed Configurations The MIC5156-3.3 and MIC5156-5.0 are preset for 3.3V and 5.0V respectively. The MIC5157 operates at 3.3V when the 3.3V pin is connected to the S (source) pin; 5.0V when the 5.0V pin is connected to the S pin; or 12V if the 3.3V and 5.0V pins are open. The MIC5158 operates at a fixed 5V (without an external resistive divider) if the 5V FB pin is connected to EA. August 2005 VOU T S * MIC5156 GND ) G Figure 1b. Connections for Adjustable Output G - 1 9 MIC5156/5157/5158 MIC5156/5157/5158 Micrel, Inc. Current Limiting Current sensing requires a low-value series resistance (Rs) between VDD and D (drain). Refer to the typical applications. The internal current-limiting circuit limits the voltage drop across the sense resistor to 35mV. Equation (2) provides the sense resistor value required for a given maximum current. 35mV 2) RS = I LI M Gate Supply VG EN Enable Shutdown VIN VDD RS D MIC5156-x.xG S GND where: RS = sense resistor value ILIM = maximum output current Figure 4a. High-Side Switch Most current-limited applications require low-value resistors. See Application Hints 21 and 25 for construction hints. Non-Current-Limited Applications If a MIC5157 or MIC5158 is used and is shutdown for a given time, the charge pump reservoir VCP will bleed off. If recharging the reservoir causes an unacceptable delay in the load reaching its operating voltage, do not use the EN pin for on/off control. Instead, use the MIC5158, hold EN high to keep the charge pump in continuous operation, and switch the MOSFET on or off by overriding the error amplifier input as shown in figure (4b). For circuits not requiring current limiting, do not use a sense resistor between VDD and D (drain). See figure (3). The controller will not limit current when it does not detect a 35mV drop from VDD to D. VIN VIN VDD VDD EN D MIC5158 MIC5156 G S MIC5156/5157/5158 1N4148 Output Off Output On 3.3V Microprocessor Applications For computer designs that use 3.3V microprocessors with 5V logic, the FLAG output can be used to suppress the 5V supply until the 3.3V output is in regulation. Refer to the external components shown with the MIC5156 Block Diagram. SMPS Post Regulator Application A Super LDO regulator can be used as a post regulator for a switch-mode power supply. The Super LDO regulator can provide a significant reduction in peak-to-peak ripple voltage. High-Current Switch Application All versions of the MIC5156/7/8 may be used for current-limited, high-current, high-side switching with or without voltage regulation. See figure (4a). Simply leave the “S” terminal open. A 16V zener diode from the gate to the source of the MOSFET protects the MOSFET from overdrive during fault conditions. S EA GND Figure 3. No Current Limit G Figure 4b. Fast High-Side Switch Battery Charger Application The MIC5158 may be used in constant-current applications such as battery chargers. See figure (5). The regulator supplies a constant-current (35mV ÷ R3) until the battery approaches the float voltage: R1 V FL = 1 . 2 3 5 1 + R2 ( ) where: VFL = float voltage At float voltage, the MOSFET is shut off. A trickle charge is supplied by R4. 10 August 2005 MIC5156/5157/5158 Micrel, Inc. Uninterruptible Power Supply The MIC5157 and two N-channel MOSFETs provide battery switching for uninterruptible power as shown in figure (6). Two MOSFETs are placed source-to-source to prevent current flow through their body diodes when switched off. The Super LDO regulator is continuously enabled to achieve fast battery switch-in. Careful attention must be paid to the ac-line monitoring circuitry to ensure that the output voltage does not fall below design limits while the battery is being switched in. VIN VDD EN R3 R4 D G MIC5158 S R1 GND EA R2 EN VDD D Figure 5. Battery Charger Concept G MIC5158 Q1 G S G GND Line Battery AC Line EA Q2 D S S MOSFET body diodes shown for clarity D 40V max. 1N4148 Off-line Power Supply Uninterruptable DC Figure 6. UPS Power Supply Concept August 2005 11 MIC5156/5157/5158 MIC5156/5157/5158 Micrel, Inc. Package Information PIN 1 DIMENSIONS: INCH (MM) 0.380 (9.65) 0.370 (9.40) 0.255 (6.48) 0.245 (6.22) 0.135 (3.43) 0.125 (3.18) 0.300 (7.62) 0.013 (0.330) 0.010 (0.254) 0.018 (0.57) 0.100 (2.54) 0.130 (3.30) 0.0375 (0.952) 0.380 (9.65) 0.320 (8.13) 8-Pin DIP (N) 8-Pin SOIC (M) MIC5156/5157/5158 12 August 2005 MIC5156/5157/5158 Micrel, Inc. .770 (19.558) MAX PIN 1 .235 (5.969) .215 (5.461) .060 (1.524) .045 (1.143) .310 (7.874) .280 (7.112) .160 MAX (4.064) .080 (1.524) .015 (0.381) .015 (0.381) .008 (0.2032) .160 (4.064) .100 (2.540) .110 (2.794) .090 (2.296) .023 (.5842) .015 (.3810) .060 (1.524) .045 (1.143) .400 (10.180) .330 (8.362) 14-Pin DIP (N) PIN 1 DIMENSIONS: INCHES (MM) 0.154 (3.90) 0.026 (0.65) MAX) 0.057 (1.45) 0.049 (1.25) 0.050 (1.27) 0.016 (0.40) TYP TYP 0.344 (8.75) 0.337 (8.55) 0.193 (4.90) 0.006 (0.15) SEATING PLANE 45 3–6 0.244 (6.20) 0.228 (5.80) 14-Pin SOIC (M) MICREL INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB http://www.micrel.com This information furnished by Micrel in this data sheet is believed to be accurate and reliable. However no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 1999 Micrel, Inc. August 2005 13 MIC5156/5157/5158