NCV8508B D

NCV8508B
5.0 V and 3.3 V, 250 mA
LDO with Watchdog and
RESET
The NCV8508B is a precision micropower Low Dropout (LDO)
voltage regulator. The part contains many of the required features for
powering microprocessors. Its robustness makes it suitable for severe
automotive environments. In addition, the NCV8508B is ideal for use
in battery operated, microprocessor controlled equipment because of
its extremely low quiescent current.
http://onsemi.com
MARKING
DIAGRAMS
Features
•
•
•
•
•
•
Output Voltage: 5.0 V and 3.3 V
±3.0% Output Voltage
IOUT Up to 250 mA
Quiescent Current Independent of Load
Micropower Compatible Control Functions:
♦ Wakeup
♦ Watchdog
♦ RESET
Low Quiescent Current (100 mA typ)
Protection Features:
♦ Thermal Shutdown
♦ Short Circuit
♦ 45 V Operation
NCV Prefix for Automotive and Other Applications Requiring Site
and Change Controls
AEC Qualified
PPAP Capable
These are Pb−Free Devices
NCV8508B
MRA4004T3
VBAT
C1*
0.1 mF
VOUT
VIN
WDI
Delay
RDelay
60 k
GND
RESET
WAKEUP
C2
1.0 mF
VDD
I/O
RESET
I/O
Microprocessor
•
•
•
•
•
D2PAK−7
DS SUFFIX
CASE 936AB
V8508yBxx
AWLYWWG
1
8
8
508yBx
ALYW
G
1
SO−8 EP
PD SUFFIX
CASE 751AC
1
xx, x
= Voltage Option
5.0 V (xx = 50, x = 5)
3.3 V (xx = 33, x = 3)
y
= Timing Option
(see Page 4 for more details)
1 (Delay Time = 3 ms @ RDelay = 60k)
2 (Delay Time = 9 ms @ RDelay = 60k)
A
= Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
G or G = Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 20 of this data sheet.
*C1 required if regulator is located far from power supply filter.
Figure 1. Application Circuit
© Semiconductor Components Industries, LLC, 2011
March, 2011 − Rev. 3
1
Publication Order Number:
NCV8508B/D
NCV8508B
PIN CONNECTIONS
1
Tab = GND
Lead
1. VOUT
2. VIN
3. WDI
4. GND
5. Wakeup
6. RESET
7. Delay
Delay
1
8
GND
RESET
Wakeup
Sense
WDI
VOUT
VIN
D2PAK−7
SO−8 EP
PACKAGE PIN DESCRIPTION
PACKAGE PIN #
D2PAK−7
SO−8 EP
PIN SYMBOL
1
4
VOUT
2
5
VIN
Supply Voltage to the IC.
3
6
WDI
CMOS compatible input lead. The Watchdog function monitors the falling
edge of the incoming signal.
4
2
GND
Ground connection.
5
7
Wakeup
CMOS compatible output consisting of a continuously generated signal used
to “wake up” the microprocessor from sleep mode.
6
8
RESET
CMOS compatible output lead RESET goes low whenever VOUT drops by
more than 7.0% from nominal, or during the absence of a correct Watchdog
signal.
7
1
Delay
−
−
NC
−
3
Sense
Kelvin connection which allows remote sensing of the output voltage for
improved regulation. Connect to VOUT if remote sensing is not required.
−
EPAD
EPAD
Connect to Ground potential or leave unconnected.
FUNCTION
Regulated output voltage ± 3.0%.
Buffered bandgap voltage used to create timing current for RESET and
Wakeup from RDelay.
No Connection.
http://onsemi.com
2
NCV8508B
VIN
−
Charge
Pump
+
11 V
Sense
Current
Limit
1.25 V
Bandgap
Reference
VOUT
Internally
connected
on 7 lead
D2PAK
Thermal
Shutdown
+
−
−
RESET
+
Watchdog
Circuit
WDI
Falling
Edge
Detect
Timing
Circuit
Delay
Wakeup
Circuit
Wakeup
Figure 2. Block Diagram
MAXIMUM RATINGS
Rating
Input Voltage, VIN (DC)
Peak Transient Voltage (46 V Load Dump @ VIN = 14 V)
Output Voltage, VOUT
ESD Susceptibility:
Human Body Model
Machine Model
Charged Device Model
Logic Inputs/Outputs (RESET, WDI, Wakeup)
Operating Junction Temperature, TJ
Storage Temperature Range, TS
Peak Reflow Soldering Temperature:
Reflow: (Note 1)
Moisture Sensitivity Level:
D2PAK−7
SO−8EP
Value
Unit
−0.3 to 45
V
60
V
−0.3 to 18
V
2.0
200
1.0
kV
V
kV
−0.3 to +7.0
V
−40 to150
°C
−55 to +150
°C
260 Peak
(Note 2)
°C
3
2
−
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. 60 second maximum above 183°C.
2. −5°C/+0°C allowable conditions.
THERMAL CHARACTERISTICS
See Package Thermal Data Section (Page 11)
http://onsemi.com
3
NCV8508B
ELECTRICAL CHARACTERISTICS (−40°C ≤ TJ ≤ 125°C; 6.0 V ≤ VIN ≤ 28 V, 100 mA ≤ IOUT ≤ 150 mA, C2 = 1.0 mF, RDelay = 60 k;
unless otherwise specified.)
Characteristic
Test Conditions
Min
Typ
Max
Unit
OUTPUT
Output Voltage
5.0 V
−
4.85
5.00
5.15
V
Output Voltage
3.3 V
−
3.201
3.3
3.399
V
Dropout Voltage (VIN − VOUT)
5.0 V
IOUT = 150 mA. Note 3
−
450
900
mV
Load Regulation
VIN = 14 V, 100 mA ≤ IOUT ≤ 150 mA
−
5.0
30
mV
Line Regulation
6.0 V ≤ VIN ≤ 28 V, IOUT = 5.0 mA
−
5.0
50
mV
−
250
400
−
mA
Thermal Shutdown
Guaranteed by Design
150
180
210
°C
Quiescent Current
VIN = 12 V, IOUT = 150 mA, (see Figure 6)
−
100
150
mA
Current Limit
RESET
Threshold
5.0 V
−
4.50
4.65
4.80
V
Threshold
3.3 V
−
2.970
3.069
3.168
V
−
0.2
0.4
0.4
0.8
V
VOUT − 0.5
VOUT − 1.0
VOUT − 0.25
VOUT − 0.5
−
V
Output Low
RLOAD = 10 k to VOUT, VOUT ≥ 1.0 V
RLOAD = 5.1 k to VOUT, VOUT ≥ 1.0 V
Output High
RLOAD = 10 k to GND
RLOAD = 5.1 k to GND
Delay Time
NCV85081B
VIN = 14 V, RDelay = 60 k, IOUT = 5.0 mA
VIN = 14 V, RDelay = 120 k, IOUT = 5.0 mA
2.0
−
3.0
6.0
4.0
−
ms
ms
Delay Time
NCV85082B
VIN = 14 V, RDelay = 60 k, IOUT = 5.0 mA
VIN = 14 V, RDelay = 120 k, IOUT = 5.0 mA
6.0
−
9.0
18
12.0
−
ms
ms
WATCHDOG INPUT
Threshold High
−
70
−
−
%VOUT
Threshold Low
−
−
−
30
%VOUT
Hysteresis
−
−
100
−
mV
−
0.1
+10
mA
5.0
−
−
ms
Input Current
WDI = 6.0 V
Pulse Width
50% WDI falling edge to
50% WDI rising edge and
50% WDI rising edge to
50% WDI falling edge, (see Figure 5)
WAKEUP OUTPUT (VIN = 14 V, IOUT = 5.0 mA)
Wakeup Period
NCV85081B
See Figures 4 and 5, RDELAY = 60 k
See Figures 4 and 5, RDELAY = 120 k
18
−
25
50
32
−
ms
ms
Wakeup Period
NCV85082B
RDELAY = 60 k
RDELAY = 120 k
54
−
75
150
96
−
ms
ms
Wakeup Duty Cycle Nominal
See Figure 3
45
50
55
%
RESET HIGH to Wakeup Rising Delay
Time
NCV85081B
RDELAY = 60 k, 50% RESET rising edge to
50% Wakeup edge
RDELAY = 120 k
(see Figures 3 and 4)
9.0
12.5
16
−
25
−
ms
ms
3. Measured when the output voltage has dropped 100 mV from the nominal value. (see Figure 12)
4. Current drain on the Delay pin directly affects the Delay Time, Wakeup Period, and the RESET to Wakeup Delay Time.
http://onsemi.com
4
NCV8508B
ELECTRICAL CHARACTERISTICS (−40°C ≤ TJ ≤ 125°C; 6.0 V ≤ VIN ≤ 28 V, 100 mA ≤ IOUT ≤ 150 mA, C2 = 1.0 mF, RDelay = 60 k;
unless otherwise specified.)
Characteristic
Test Conditions
Min
Typ
Max
Unit
ms
ms
WAKEUP OUTPUT (VIN = 14 V, IOUT = 5.0 mA)
RESET HIGH to Wakeup Rising Delay
Time
NCV85082B
RDELAY = 60 k, 50% RESET rising edge to
50% Wakeup edge
RDELAY = 120 k
27
37.5
48
−
75
−
Wakeup Response to
Watchdog Input
50% WDI falling edge to
50% Wakeup falling edge
−
0.1
5.0
ms
Wakeup Response to RESET
50% RESET falling edge to
50% Wakeup falling edge
VOUT = VOUT_NOM −> 90% of VOUT_NOM
−
0.1
5.0
ms
Output Low
RLOAD = 10 k to VOUT, VOUT ≥ 1.0 V
RLOAD = 5.1 k to VOUT, VOUT ≥ 1.0 V
−
0.2
0.4
0.4
0.8
V
Output High
RLOAD = 10 k to GND
RLOAD = 5.1 k to GND
VOUT − 0.5
VOUT − 1.0
VOUT − 0.25
VOUT − 0.5
−
V
IDELAY = 50 mA. Note 4
−
1.25
−
V
DELAY
Output Voltage
3. Measured when the output voltage has dropped 100 mV from the nominal value. (see Figure 12)
4. Current drain on the Delay pin directly affects the Delay Time, Wakeup Period, and the RESET to Wakeup Delay Time.
http://onsemi.com
5
NCV8508B
TIMING DIAGRAMS
VIN
RESET
Wakeup
Duty Cycle = 50%
Wakeup
WDI
VOUT
WDI Pulse Must Occur with Wakeup in
Low State for 50% Duty Cycle.
Reference Figure 18 for Occurrence of
WDI with Wakeup in High State.
POR
RESET High
to Wakeup
Delay Time
Power Up
Microprocessor
Sleep Mode
Normal Operation with Varying Watchdog Signal
Figure 3. Power Up, Sleep Mode and Normal Operation
VIN
RESET Delay Time
RESET
Wakeup
WDI
VOUT
POR
RESET High
to Wakeup
Delay Time
Wakeup
Period
RESET High
to Wakeup
Delay Time
Figure 4. Error Condition: Watchdog Remains Low and a RESET Is Issued
RESET
Wakeup Period
Wakeup
WDI
RESET Threshold
VOUT
Watchdog
Pulse Width
POR
Power Down
POR
Watchdog Pulse Width
Figure 5. Power Down and Restart Sequence
http://onsemi.com
6
NCV8508B
TYPICAL PERFORMANCE CHARACTERISTICS
110
−700
100
trise/fall = 1.0 ms (Switching Current)
−600
VOUT Transient (mV)
Quiescent Current (mA)
−40°C
+25°C
90
+125°C
1.0 mF
−500
−400
10 mF
−300
−200
100 mF
−100
80
0
50
100
150
Output Current (mA)
200
0
250
0
Figure 6. Quiescent Current vs Output Current
200
250
40
9
35
NCV85082B
30
POR Delay (ms)
8
POR Delay (ms)
100
150
Switching Current (mA)
Figure 7. Load Transient Response
10
7
6
5
4
25
NCV85082B
20
15
NCV85081B
10
NCV85081B
3
5
2
−40 −20
0
20
0
15
40
60 80 100 120 140 160
TJ, Temperature (°C)
Figure 8. Reset Delay Time vs Junction
Temperature
60
105
150
RDELAY (kW)
195
240
Figure 9. Reset Delay Time vs Reset Delay
Resistor
350
90
80
300
70
NCV85082B
Wakeup Period (ms)
Wakeup Period (ms)
50
60
50
40
NCV85081B
30
20
250
NCV85082B
200
150
100
NCV85081B
50
10
0
−40 −20
0
0
15
20 40 60 80 100 120 140 160
TJ, Temperature (°C)
Figure 10. Wakeup Period vs Junction
Temperature
60
105
150
RDELAY (kW)
195
Figure 11. Wakeup Period vs Reset Delay
Resistor
http://onsemi.com
7
240
NCV8508B
TYPICAL PERFORMANCE CHARACTERISTICS
5.10
1.0
VIN = 14 V
IOUT = 5.0 mA
0.9
+125°C
0.7
0.6
Output Voltage (V)
Dropout Voltage (V)
0.8
+25°C
0.5
0.4
0.3
−40°C
0.2
5.05
5.00
4.95
0.1
0.0
0
50
200
100
150
Output Current (mA)
4.90
−40 −20
250
Figure 12. Dropout Voltage vs Output Current
20 40 60
80 100 120 140 160
TJ, Temperature (°C)
Figure 13. Output Voltage vs Junction
Temperature, 5 V
3.40
VIN = 14 V
IOUT = 5.0 mA
3.38
3.36
Output Voltage (V)
0
3.34
3.32
3.30
3.28
3.26
3.24
3.22
3.20
−40 −20
0
20 40 60
80 100 120 140 160
TJ, Temperature (°C)
Figure 14. Output Voltage vs Junction
Temperature, 3.3 V
100
160
COUT = 1.0 mF − 100 mF
10
120
100
ESR (W)
Output Current (mA)
140
80
60
RL = 33 W
40
Stable Region
1
0.1
20
0
0
1
2
3
4
Input Voltage (V)
5
0.01
6
0
50
100
150
200
Output Current (mA)
Figure 15. Output Current vs Input Voltage
Figure 16. Output Capacitor ESR
http://onsemi.com
8
250
NCV8508B
DEFINITION OF TERMS
Dropout Voltage: The input−output voltage differential at
which the circuit ceases to regulate against further reduction
in input voltage. Measured when the output voltage has
dropped 100 mV from the nominal value obtained at 14 V
input, dropout voltage is dependent upon load current and
junction temperature.
Input Voltage: The DC voltage applied to the input
terminals with respect to ground.
Line Regulation: The change in output voltage for a
change in the input voltage. The measurement is made under
conditions of low dissipation or by using pulse techniques
such that the average chip temperature is not significantly
affected.
Load Regulation: The change in output voltage for a
change in load current at constant chip temperature.
Quiescent Current: The part of the positive input current
that does not contribute to the positive load current. The
regulator ground lead current.
Ripple Rejection: The ratio of the peak−to−peak input
ripple voltage to the peak−to−peak output ripple voltage.
Current Limit: Peak current that can be delivered to the
output.
DETAILED OPERATING DESCRIPTION
The NCV8508B is a precision micropower voltage
regulator with very low quiescent current (100 mA typical at
250 mA load). A typical dropout voltage is 450 mV at
150 mA for 5 V option. Microprocessor control logic
includes Watchdog, Wakeup and RESET. This unique
combination of extremely low quiescent current and full
microprocessor control makes the NCV8508B ideal for use
in battery operated, microprocessor controlled equipment in
addition to being a good fit in the automotive environment.
The NCV8508B Wakeup function brings the
microprocessor out of Sleep mode. The microprocessor in
turn signals its Wakeup status back to the NCV8508B by
issuing a Watchdog signal.
The Watchdog logic function monitors an input signal
(WDI) from the microprocessor. The NCV8508B responds
to the falling edge of the Watchdog signal which it expects
at least once during each Wakeup period. When the correct
Watchdog signal is received, a falling edge is issued on the
Wakeup signal line.
RESET is independent of VIN and operates correctly to an
output voltage as low as 1.0 V. A signal is issued in any of
three situations. During power up, the RESET is held low
until the output voltage is in regulation. During operation, if
the output voltage shifts below the regulation limits, the
RESET toggles low and remains low until proper output
voltage regulation is restored. Finally, a RESET signal is
issued if the regulator does not receive a Watchdog signal
within the Wakeup period.
The RESET pulse width, Wakeup signal frequency, and
Wakeup delay time are all set by one external resistor,
RDelay.
The Delay pin is a buffered bandgap voltage (1.25 V). It
can be used as a reference for an external tracking regulator
as shown in Figure 17.
The regulator is protected against short circuit and thermal
runaway conditions. The device runs through 45 volt
transients, making it suitable for use in automotive
environments.
MRA4004T3
200 mA
VIN
VIN
VBAT
0.1 mF
VOUT
1.0 mF
NCV8508B
12 k
CS8182
Adj
3.9 k
Delay
GND
VREF/ENABLE
60 k
0.1 mF
Figure 17. Application Circuit
http://onsemi.com
9
5V
GND
10 mF
NCV8508B
CIRCUIT DESCRIPTION
Functional Description
Resistor temperature coefficient and tolerance as well as
the tolerance of the NCV8508B must be taken into account
in order to get the correct system tolerance for each
parameter.
To reduce the drain on the battery, a system can go into a
low current consumption mode whenever it is not
performing a main routine. The Wakeup signal is generated
continuously and is used to interrupt a microcontroller that
is in sleep mode. The nominal output is a 5.0 (or 3.3 V) volt
square wave (voltage generated from VOUT) with a duty
cycle of 50% at a frequency that is determined by a timing
resistor, RDelay.
When the microprocessor receives a rising edge from the
Wakeup output, it must issue a Watchdog pulse and check its
inputs to decide if it should resume normal operations or
remain in the sleep mode.
The first falling edge of the Watchdog signal causes the
Wakeup to go low within 2.0 ms (typ) and remain low until
the next Wakeup cycle (see Figure 18). Other Watchdog
pulses received within the same cycle are ignored (Figure 3).
During power up, RESET is held low until the output
voltage is in regulation. During operation, if the output
voltage shifts below the regulation limits, the RESET
toggles low and remains low until proper output voltage
regulation is restored. After the RESET delay, RESET
returns high.
The Watchdog circuitry continuously monitors the input
Watchdog signal (WDI) from the microprocessor. The
absence of a falling edge on the Watchdog input during one
Wakeup cycle will cause a RESET pulse to occur at the end
of the Wakeup cycle. (see Figure 4).
The Wakeup output is pulled low during a RESET
regardless of the cause of the RESET. After the RESET
returns high, the Wakeup cycle begins again (see Figure 4).
The RESET Delay Time, Wakeup signal frequency and
RESET high to Wakeup delay time are all set by one external
resistor RDelay.
Wakeup Period = (4.17 × 10−7)RDelay
RESET Delay Time = (5.21 × 10−8)RDelay
RESET HIGH to Wakeup Delay Time = (2.08 × 10−7)RDelay
WDI
Wakeup
Wakeup
Response
to WDI
Figure 18. Wakeup Response to WDI
RESET
Wakeup
Wakeup
Response
to RESET
Figure 19. Wakeup Response to RESET (Low
Voltage)
http://onsemi.com
10
NCV8508B
Recommend Thermal Data for D2PAK−7 Package
Parameter
Test Conditions Typical Value
Units
min−pad board (Note 5)
1”−pad board (Note 6)
Junction−to−Lead (psi−JL, YJL)
12
12
°C/W
Junction−to−Ambient (RqJA, qJA)
84
48
°C/W
5. 1 oz. copper, 118 mm2 copper area, 0.062” thick FR4.
6. 1 oz. copper, 626 mm2 copper area, 0.062” thick FR4.
Package construction
With and without mold compound
Various copper areas used
for heat spreading
Active Area (red) times 2
(only showing 1/2 symmetry)
Figure 20. PCB Layout and Package Construction for Simulation
http://onsemi.com
11
NCV8508B
Table 1. D2PAK 7−Lead Thermal RC Network Models
118 mm2
626 mm2
118 mm2
Cauer Network
626 mm2
Cu Area
Foster Network
C’s
C’s
Units
Tau
Tau
units
1
8.6E−07
8.6E−07
W−s/C
1.00E−07
1.00E−07
sec
2
3.6E−06
3.6E−06
W−s/C
1.00E−06
1.00E−06
sec
3
1.4E−05
1.4E−05
W−s/C
1.00E−05
1.00E−05
sec
4
1.4E−04
1.4E−04
W−s/C
3.07E−04
3.07E−04
sec
5
6.4E−04
6.4E−04
W−s/C
1.00E−03
1.00E−03
sec
6
1.1E−02
1.1E−02
W−s/C
6.00E−03
6.00E−03
sec
7
3.0E−02
3.0E−02
W−s/C
2.00E−02
2.00E−02
sec
8
4.9E−01
5.2E−01
W−s/C
1.43E+00
1.43E+00
sec
9
4.8E−01
1.5E+00
W−s/C
6.15E+00
3.82E+00
sec
10
6.9E−01
9.5E−01
W−s/C
1.04E+02
9.68E+01
sec
R’s
R’s
R’s
R’s
1
0.147
0.147
C/W
0.090
0.090
C/W
2
0.301
0.301
C/W
0.194
0.194
C/W
3
0.603
0.603
C/W
0.614
0.614
C/W
4
2.733
2.733
C/W
1.200
1.200
C/W
5
1.178
1.178
C/W
2.600
2.600
C/W
6
1.369
1.366
C/W
0.100
0.100
C/W
7
0.272
0.270
C/W
1.700
1.700
C/W
8
14.820
7.855
C/W
0.100
0.100
C/W
9
6.055
2.741
C/W
6.944
5.181
C/W
10
56.834
30.488
C/W
70.770
35.902
C/W
NOTE:
Bold face items in the Cauer network above, represent the package without the external thermal system. The Bold face items in
the Foster network are computed by the square root of time constant R(t) = 166 * sqrt(time(sec)). The constant is derived based
on the active area of the device with silicon and epoxy at the interface of the heat generation.
The Cauer networks generally have physical significance and may be divided between nodes to separate thermal behavior
due to one portion of the network from another. The Foster networks, though when sorted by time constant (as above) bear
a rough correlation with the Cauer networks, are really only convenient mathematical models. Cauer networks can be easily
implemented using circuit simulating tools, whereas Foster networks may be more easily implemented using mathematical
tools (for instance, in a spreadsheet program), according to the following formula:
n
R(t) +
S Ri ǒ1−e−tńtaui Ǔ
i+1
http://onsemi.com
12
NCV8508B
qJA vs Copper Spreader Area
100
90
80
1 oz
qJA (°C/W)
70
60
2 oz
50
40
30
20
10
0
0
100
200
300
400
500
600
700
800
COPPER AREA (mm2)
Figure 21. D2PAK 7−lead qJA as a Function of the
Pad Copper Area Including Traces, Board Material
100
Cu Area 118 mm2, 1 oz
R(t) (°C/W)
10
Cu Area 626 mm2, 1 oz
1
0.1
0.000001
0.00001
0.0001
0.001
0.1
0.01
Time (sec)
1
10
100
1000
Figure 22. D2PAK 7−Lead Single Pulse Heating Curve
100
R(t) (°C/W)
50% Duty Cycle
10
20%
10%
5%
1
1%
Single
0.1
0.000001
Cu Area 626 mm2, 1 oz Cu
0.00001
0.0001
0.001
0.1
0.01
Pulse Duration (sec)
1
10
Figure 23. D2PAK 7−Lead Thermal Duty Cycle Curves on 1” Spreader Test Board
http://onsemi.com
13
100
1000
NCV8508B
R1
Junction
C1
R2
C2
R3
C3
Rn
Cn
Time constants are not simple RC products. Amplitudes
of mathematical solution are not the resistance values.
Ambient
(thermal ground)
Figure 24. Grounded Capacitor Thermal Network (“Cauer” Ladder)
Junction
R1
C1
R2
C2
R3
C3
Rn
Cn
Each rung is exactly characterized by its RC−product
time constant; amplitudes are the resistances.
Ambient
(thermal ground)
Figure 25. Non−Grounded Capacitor Thermal Ladder (“Foster” Ladder)
http://onsemi.com
14
NCV8508B
Recommend Thermal Data for SOIC−8 EP Package
Parameter
Test Conditions Typical Value
Units
min−pad board (Note 7)
1”−pad board (Note 8)
Junction−to−Lead (psi−JL, YJL)
38
24
°C/W
Junction−to−Lead (psi−JPad, YJp)
8.0
9.0
°C/W
Junction−to−Ambient (RqJA, qJA)
126
64
°C/W
Pad is soldered to PCB copper
7. 1 oz. copper, 54 mm2 copper area, 0.062” thick FR4.
8. 1 oz. copper, 717 mm2 copper area, 0.062” thick FR4.
8−SOIC EP Half Symmetry
Top view
With and without mold compound
Bottom view
With mold compound
Copper Pad Layout
25 x 25mm
Figure 26. Internal Construction of the Package and PCB Layout for Multiple Pad Area
http://onsemi.com
15
NCV8508B
Table 2. SOIC 8−Lead EP Thermal RC Network Models
54 mm2
717 mm2
54 mm2
Cauer Network
717 mm2
Cu Area
Foster Network
C’s
C’s
Units
Tau
Tau
units
1
2.7E−06
2.7E−06
W−s/C
1.00E−06
1.00E−06
sec
2
1.1E−05
1.1E−05
W−s/C
1.00E−05
1.00E−05
sec
3
3.2E−05
3.2E−05
W−s/C
1.00E−04
1.00E−04
sec
4
1.3E−04
1.3E−04
W−s/C
9.39E−04
9.39E−04
sec
5
1.8E−03
1.8E−03
W−s/C
3.13E−03
3.13E−03
sec
6
7.9E−03
8.3E−03
W−s/C
3.30E−02
3.30E−02
sec
7
2.5E−02
3.1E−02
W−s/C
6.00E−01
6.00E−01
sec
8
1.4E−01
5.1E−01
W−s/C
4.00E+00
4.00E+00
sec
9
4.1E−01
2.1E+00
W−s/C
1.16E+01
4.83E+01
sec
10
1.6E+00
6.3E+01
W−s/C
5.58E+01
2.37E+02
sec
R’s
R’s
R’s
R’s
1
0.474
0.474
C/W
0.282
0.282
C/W
2
1.086
1.086
C/W
0.610
0.610
C/W
3
3.011
3.010
C/W
1.929
1.929
C/W
4
5.883
5.874
C/W
5.825
5.825
C/W
5
1.944
1.911
C/W
2.700
2.700
C/W
6
4.655
4.264
C/W
3.000
3.000
C/W
7
21.431
15.678
C/W
15.000
15.000
C/W
8
40.130
9.238
C/W
11.494
7.797
C/W
9
23.392
18.454
C/W
34.982
20.473
C/W
10
24.381
3.581
C/W
50.566
5.953
C/W
NOTE:
Bold face items in the Cauer network above, represent the package without the external thermal system. The Bold face items in
the Foster network are computed by the square root of time constant R(t) = 225 * sqrt(time(sec)). The constant is derived based
on the active area of the device with silicon and epoxy at the interface of the heat generation.
The Cauer networks generally have physical significance and may be divided between nodes to separate thermal behavior
due to one portion of the network from another. The Foster networks, though when sorted by time constant (as above) bear
a rough correlation with the Cauer networks, are really only convenient mathematical models. Cauer networks can be easily
implemented using circuit simulating tools, whereas Foster networks may be more easily implemented using mathematical
tools (for instance, in a spreadsheet program), according to the following formula:
n
R(t) +
S Ri ǒ1−e−tńtaui Ǔ
i+1
http://onsemi.com
16
NCV8508B
qJA vs Copper Spreader Area
140
120
qJA (°C/W)
100
1 oz
80
60
2 oz
40
20
0
0
100
200
300
400
500
600
700
800
COPPER AREA (mm2)
Figure 27. SOIC 8−Lead EP qJA as a Function of the
Pad Copper Area Including Traces, Board Material
1000
Cu Area 54 mm2, 1 oz
R(t) (°C/W)
100
Cu Area 717 mm2, 1 oz
10
1
0.1
0.000001
0.00001
0.0001
0.001
0.01
0.1
1
10
100
1000
10
100
1000
Time (sec)
Figure 28. SOIC 8−Lead EP Single Pulse Heating Curve
100
50% Duty Cycle
R(t) (°C/W)
20%
10
10%
5%
1
1%
Single
0.1
0.000001
Cu Area 717 mm2, 1 oz Cu
0.00001
0.0001
0.001
0.1
0.01
Time (sec)
1
Figure 29. SOIC 8−Lead Thermal Duty Cycle Curves on 1” Spreader Test Board
http://onsemi.com
17
NCV8508B
R1
Junction
C1
R2
C2
R3
C3
Rn
Cn
Time constants are not simple RC products. Amplitudes
of mathematical solution are not the resistance values.
Ambient
(thermal ground)
Figure 30. Grounded Capacitor Thermal Network (“Cauer” Ladder)
Junction
R1
C1
R2
C2
R3
C3
Rn
Cn
Each rung is exactly characterized by its RC−product
time constant; amplitudes are the resistances.
Ambient
(thermal ground)
Figure 31. Non−Grounded Capacitor Thermal Ladder (“Foster” Ladder)
http://onsemi.com
18
NCV8508B
APPLICATION NOTES
Calculating Power Dissipation in a Single Output
Linear Regulator
The value of RqJA can then be compared with those in the
package section of the data sheet. Those packages with
RqJAs less than the calculated value in Equation 2 will keep
the die temperature below 150°C.
In some cases, none of the packages will be sufficient to
dissipate the heat generated by the IC, and an external
heatsink will be required.
The maximum power dissipation for a single output
regulator (Figure 32) is:
PD(max) + [VIN(max) * VOUT(min)] IOUT(max)
(1)
) VIN(max)IQ
where:
VIN(max) is the maximum input voltage,
VOUT(min) is the minimum output voltage,
IOUT(max) is the maximum output current for the
application, and
IQ is the quiescent current the regulator consumes at
IOUT(max).
IIN
VIN
SMART
REGULATOR
}
Heatsinks
A heatsink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment will have a thermal resistance. Like
series electrical resistances, these resistances are summed to
determine the value of RqJA:
IOUT
VOUT
RqJA + RqJC ) RqCS ) RqSA
where:
RqJC = the junction−to−case thermal resistance,
RqCS = the case−to−heatsink thermal resistance, and
RqSA = the heatsink−to−ambient thermal resistance.
RqJC appears in the package section of the data sheet. Like
RqJA, it too is a function of package type. RqCS and RqSA are
functions of the package type, heatsink and the interface
between them. These values appear in data sheets of
heatsink manufacturers.
Control
Features
IQ
Figure 32. Single Output Regulator with Key
Performance Parameters Labeled
Once the value of PD(max) is known, the maximum
permissible value of RqJA can be calculated:
T
RqJA + 150° C * A
PD
(3)
(2)
http://onsemi.com
19
NCV8508B
ORDERING INFORMATION
Device
Output Voltage
Timing Option
(RDelay = 60 kΩ)
Package
Shipping†
NCV85081BDS50G
5.0 V
Delay Time = 3 ms
Wakeup Period = 25 ms
RESET HIGH to
Wakeup Rising Delay Time = 12.5 ms
D2PAK*7
(Pb*Free)
50 Units / Rail
NCV85081BDS50R4G
5.0 V
Delay Time = 3 ms
Wakeup Period = 25 ms
RESET HIGH to
Wakeup Rising Delay Time = 12.5 ms
D2PAK*7
(Pb*Free)
750 / Tape & Reel
NCV85081BPD50R2G
5.0 V
Delay Time = 3 ms
Wakeup Period = 25 ms
RESET HIGH to
Wakeup Rising Delay Time = 12.5 ms
SO*8 EP
(Pb*Free)
2500 / Tape & Reel
NCV85082BPD33R2G
3.3 V
Delay Time = 9 ms
Wakeup Period = 75 ms
RESET HIGH to
Wakeup Rising Delay Time = 37.5 ms
SO*8 EP
(Pb*Free)
2500 / Tape & Reel
NOTE: Contact factory for other options.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
20
NCV8508B
PACKAGE DIMENSIONS
SOIC−8 EP
CASE 751AC−01
ISSUE B
2X
D
E1
2X
0.10 C D
PIN ONE
LOCATION
DETAIL A
D
A
8
EXPOSED
PAD
5
ÉÉÉ
ÉÉÉ
ÉÉÉ
1
5
F
8
G
E
h
2X
4
4
0.20 C
e
1
BOTTOM VIEW
8X b
0.25 C A-B D
B
A
0.10 C
A2
8X
c
H
A
SEATING
PLANE
SIDE VIEW
A1
ÇÇ
ÉÉ
ÉÉ
ÇÇ
ÉÉ
ÇÇ
b1
GAUGE
PLANE
0.10 C
A
END VIEW
TOP VIEW
C
NOTES:
1. DIMENSIONS AND TOLERANCING PER
ASME Y14.5M, 1994.
2. DIMENSIONS IN MILLIMETERS (ANGLES
IN DEGREES).
3. DIMENSION b DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE
0.08 MM TOTAL IN EXCESS OF THE “b”
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
4. DATUMS A AND B TO BE DETERMINED
AT DATUM PLANE H.
0.10 C A-B
L
0.25
(L1)
DETAIL A
q
c1
(b)
SECTION A−A
SOLDERING FOOTPRINT*
2.72
0.107
1.52
0.060
7.0
0.275
Exposed
Pad
4.0
0.155
2.03
0.08
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
21
DIM
A
A1
A2
b
b1
c
c1
D
E
E1
e
L
L1
F
G
h
q
MILLIMETERS
MIN
MAX
1.35
1.75
0.00
0.10
1.35
1.65
0.31
0.51
0.28
0.48
0.17
0.25
0.17
0.23
4.90 BSC
6.00 BSC
3.90 BSC
1.27 BSC
0.40
1.27
1.04 REF
2.24
3.20
1.55
2.51
0.25
0.50
0_
8_
NCV8508B
PACKAGE DIMENSIONS
D2PAK−7 (SHORT LEAD)
CASE 936AB−01
ISSUE B
A
E
L1
0.10
A
E/2
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH AND GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.005 MAXIMUM PER SIDE. THESE DIMENSIONS
TO BE MEASURED AT DATUM H.
4. THERMAL PAD CONTOUR OPTIONAL WITHIN
DIMENSIONS E, L1, D1, AND E1. DIMENSIONS
D1 AND E1 ESTABLISH A MINIMUM MOUNTING
SURFACE FOR THE THERMAL PAD.
SEATING
PLANE
B
A
M
B A
M
E1
c2
D1
D
7X
H
e
b
0.13
M
B A
DETAIL C
VIEW A−A
c
A
M
B
H
SEATING
PLANE
A1
RECOMMENDED
SOLDERING FOOTPRINT*
0.424
DIM
A
A1
b
c
c2
D
D1
E
E1
e
H
L
L1
L3
M
INCHES
MIN
MAX
0.170
0.180
0.000
0.010
0.026
0.036
0.017
0.026
0.045
0.055
0.325
0.368
0.270
−−−
0.380
0.420
0.245
−−−
0.050 BSC
0.539
0.579
0.058
0.078
−−−
0.066
0.010 BSC
0°
8°
MILLIMETERS
MIN
MAX
4.32
4.57
0.00
0.25
0.66
0.91
0.43
0.66
1.14
1.40
8.25
9.53
6.86
−−−
9.65
10.67
6.22
−−−
1.27 BSC
13.69
14.71
1.47
1.98
−−−
1.68
0.25 BSC
0°
8°
L
M
0.310
L3
0.584
GAUGE
PLANE
DETAIL C
0.136
7X
0.050
PITCH
0.040
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
22
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCV8508B/D