NCP5662 D

NCP5662, NCV5662
Low Output Voltage,
Ultra-Fast 2.0 A Low Dropout
Linear Regulator with Enable
The NCP5662/NCV5662 is a high performance, low dropout linear
regulator designed for high power applications that require up to 2.0 A
current. It is offered in both fixed and adjustable output versions. With
output voltages as low as 0.9 V and ultra−fast response times for load
transients, the NCP5662/NCV5662 also provides additional features
such as Enable and Error Flag (for the fixed output version),
increasing the utility of these devices. A thermally robust, 5 pin
D2PAK or DFN8 package, combined with an architecture that offers
low ground current (independent of load), provides for a superior
high−current LDO solution.
Features
•
•
•
•
•
•
•
•
•
•
•
•
Ultra−Fast Transient Response (Settling Time: 1−3 ms)
Low Noise Without Bypass Capacitor (26 mVrms)
Low Ground Current Independent of Load (3.0 mA Maximum)
Fixed/Adjustable Output Voltage Versions
Enable Function
Error Flag (Fixed Output Version)
Current Limit Protection
Thermal Shutdown Protection (160°C)
0.9 V Reference Voltage for Ultra−Low Output Operation
Power Supply Rejection Ratio > 65 dB
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These are Pb−Free Devices
MARKING DIAGRAMS AND
PIN ASSIGNMENTS
1
5
D2PAK
DS SUFFIX
CASE 936AA
NC
x5662DSy
AWLYWWG
1
1
DFN8
MN SUFFIX
CASE 488AF
Fixed Version
Pin 1 = EF
2 = GND
3 = N/C
4 = EN
5, 6 = Vin
7, 8 = Vout
Tab = GND
Pin 1 = EN
2 = Vin
3 = GND
4 = Vout
5 = ADJ/EF
NCP5
662y
ALYW G
G
Adjustable Version
Pin 1 = ADJ
2 = GND
3 = N/C
4 = EN
5, 6 = Vin
7 = Vout
8 = N/C
x
y
= P or V
= A for Adjustable Version
B for Fixed 1.5 V Version
C for Fixed 3.3 V Version
D for Fixed 1.2 V Version
E for Fixed 1.8 V Version
F for Fixed 2.5 V Version
G for Fixed 2.8 V Version
H for Fixed 3.0 V Version
A
= Assembly Location
L
= Wafer Lot
Y
= Year
WW = Work Week
G or G = Pb−Free Package
Applications
•
•
•
•
•
•
http://onsemi.com
Servers
ASIC Power Supplies
Post Regulation for Power Supplies
Constant Current Source
Networking Equipment
Gaming and STB Modules
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 13 of this data sheet.
© Semiconductor Components Industries, LLC, 2013
May, 2013 − Rev. 15
1
Publication Order Number:
NCP5662/D
NCP5662, NCV5662
REF
Vin
Vin
NCP5662
NCV5662
EN
Vout
Vin
Error Flag
EF
GND
Cin
Vout
Cin
Vin
NCP5662
NCV5662
R1
GND
Enable
Enable
OFF ON
OFF ON
Figure 1. Typical Application Schematic, Fixed
Output
Cout
ADJ
EN
Cout
Vout
Vout
R2
Figure 2. Typical Application Schematic,
Adjustable Output
PIN FUNCTION DESCRIPTION
Pin
Adj/Fixed
D2PAK
Pin
Adj/Fixed
DFN8
Pin Name
Description
1
4
EN
Enable. This pin allows for on/off control of the regulator. To disable
the device, connect to Ground. If this function is not in use, connect
to Vin.
2
5, 6*
Vin
Positive Power Supply Input Voltage
3, TAB
2
GND
Power Supply Ground
4
7, 8
Vout
Regulated Output Voltage
5
1
ADJ
(Adjustable Version)
5
1
EF
(Fixed Version)
−
3, 8
Pin 3 N/C on Fixed & ADJ Version
while Pin 8 N/C on ADJ Version only
No connection. True no connect. PCB runs allowable.
−
EPAD
EPAD
Exposed thermal pad should be connected to ground.
This pin is connected to the resistor divider network and programs
the output voltage.
An Error Flag is triggered when the output voltage is out of regulation
excluding transient signals that may occur. Requires a pullup resistor
f 100 kW.
*Pins 5 and 6 must be connected together externally for output current full range operation.
http://onsemi.com
2
NCP5662, NCV5662
Vin
Voltage
Reference
Block
Vref = 0.9 V
R3
EN
Enable
Block
Vout
Output
Stage
Cc
R1
R4
R2
Error
Flag
EF
GND
Figure 3. Block Diagram, Fixed Output
Vin
Enable
Block
Voltage
Reference
Block
EN
Vref = 0.9 V
R3
Output
Stage
Vout
ADJ
R4
GND
Figure 4. Block Diagram, Adjustable Output
http://onsemi.com
3
NCP5662, NCV5662
ABSOLUTE MAXIMUM RATINGS
Symbol
Value
Unit
Input Voltage (Note 1)
Rating
Vin
18
V
Output Pin Voltage
Vout
−0.3 to (Vin +0.3)
V
Adjust Pin Voltage
VADJ
−0.3 to (Vin +0.3)
V
Enable Pin Voltage
VEN
−0.3 to (Vin +0.3)
V
Error Flag Voltage
VEF
−0.3 to (Vin +0.3)
V
IEF
3.0
mA
TJ(max)
150
°C
Error Flag Current
Maximum Junction Temperature
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
NOTE: This device series contains ESD protection and exceeds the following tests:
Human Body Model (HBM), Class 3A, 2000 V
Machine Model (MM), Class C, 200 V
Charge Device Model (CDM), Class IV, 2000 V.
1. Refer to Electrical Characteristics and Application Information for Safe Operating Area.
THERMAL CHARACTERISTICS
Rating
Symbol
Value
RqJA
RqJC
RYJL
45
5.0
7.0
RqJA
RYJL
78
14
D2PAK
Thermal Characteristics,
(Notes 1 and 2)
Thermal Resistance, Junction−to−Ambient
Thermal Resistance, Junction−to−Case
Thermal Reference, Junction−to−Lead
Unit
°C/W
Thermal Characteristics, DFN8 (Notes 1 and 2)
Thermal Resistance, Junction−to−Ambient
Thermal Reference, Junction−to−Lead (Note 3)
°C/W
2. As measured using a copper heat spreading area of 1 sq in copper, 1 oz copper thickness.
3. Lead 6.
OPERATING RANGES
Rating
Operating Input Voltage (Note 1)
Operating Ambient Temperature Range
NCP5662
NCV5662
Storage Temperature Range
4. Minimum Vin = (Vout + VDO) or 2 V, whichever is higher.
http://onsemi.com
4
Symbol
Value
Unit
Vin
(Vout+VDO), 2 to 9 (Note 4)
V
TA
−40 to +85
−40 to +125
°C
Tstg
−55 to +150
°C
NCP5662, NCV5662
ELECTRICAL CHARACTERISTICS (Vin = Vout + 1.5 V, for typical values TA = 25°C, for min/max values TA = −40°C to 85°C (NCP
version), TA = −40°C to 125°C (NCV version), Cin = Cout = 150 mF unless otherwise noted. (Note 5))
Characteristic
Symbol
Min
Typ
Max
Unit
Vn
−
26
−
mVrms
(−1%)
(−1.5%)
(−2%)
−
0.9
−
(+1%)
(+1.5%)
(+2%)
ADJUSTABLE OUTPUT VERSION
Output Noise Voltage
Output Voltage
TA = 25°C (Vin = Vout +1.5 V to 7.0 V, Iout = 10 mA to 2.0 A)
TA = −20 to +125°C (Vin = Vout +1.5 V to 7.0 V, Iout = 10 mA to 2.0 A)
TA = −40 to +150°C (Vin = Vout +1.5 V to 7.0 V, Iout = 10 mA to 2.0 A)
Adjustable Pin Input Current
Vout
V
IADJ
−
40
−
nA
Line Regulation (Iout = 10 mA, Vout+1.5 V < Vin < 7.0 V)
REGline
−
0.03
−
%
Load Regulation (10 mA < Iout < 2.0 A)
REGload
−
0.03
−
%
VDO
−
1.0
1.3
V
Peak Output Current Limit
Iout(peak)
2.0
−
−
A
Internal Current Limitation
ILIM
−
3.0
−
A
Ripple Rejection (120 Hz)
Ripple Rejection (1 kHz)
RR
−
−
70
65
−
−
dB
IGND
IGND(DIS)
−
−
1.3
10
3.0
300
mA
mA
1.3
−
−
−
−
0.3
−
−
0.5
0.5
−
−
Dropout Voltage (Iout = 2.0 A)
Ground Current
Iout = 2.0 A
Disabled State
Enable Input Threshold Voltage
VEN
Voltage Increasing, On state, Logic High
Voltage Decreasing, Off state, Logic Low
Enable Input Current
V
IEN
Enable Pin Voltage = 0.3 Vmax
Enable Pin Voltage = 1.3 Vmin
mA
5. Performance guaranteed over specified operating conditions by design, guard banded test limits, and/or characterization, production tested at
TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
http://onsemi.com
5
NCP5662, NCV5662
ELECTRICAL CHARACTERISTICS (Vin = Vout + 1.5 V, for typical values TA = 25°C, for min/max values TA = −40°C to 85°C (NCP
version), TA = −40°C to 125°C (NCV version), Cin = Cout = 150 mF unless otherwise noted. (Note 6))
Characteristic
Symbol
Min
Typ
Max
Unit
Vn
−
26
−
mVrms
(−1%)
(−1.5%)
(−2%)
−
Vout(nom)
−
(+1%)
(+1.5%)
(+2%)
FIXED OUTPUT VOLTAGE
Output Noise Voltage (Vout = 0.9 V)
Output Voltage (Note 7)
TA = 25°C (Vin = Vout +1.5 V to 7.0 V, Iout = 10 mA to 2.0 A)
TA = −20 to +125°C (Vin = Vout +1.5 V to 7.0 V, Iout = 10 mA to 2.0 A)
TA = −40 to +150°C (Vin = Vout +1.5 V to 7.0 V, Iout = 10 mA to 2.0 A)
Vout
V
Line Regulation (Iout = 10 mA, Vout+1.5 V < Vin < 7.0 V)
REGline
−
0.03
−
%
Load Regulation (10 mA < Iout < 2.0 A)
REGload
−
0.2
−
%
VDO
−
1.0
1.3
V
Peak Output Current Limit
Iout(peak)
2.0
−
−
A
Internal Current Limitation
ILIM
−
3.0
−
A
Ripple Rejection (120 Hz)
Ripple Rejection (1 kHz)
RR
−
−
70
65
−
−
dB
IGND
IGND(DIS)
−
−
1.3
30
3.0
300
mA
mA
1.3
−
−
−
−
0.3
−
−
0.5
0.5
−
−
mA
Dropout Voltage (Iout = 2.0 A)
Ground Current
Iout = 2.0 A
Disabled State
Enable Input Threshold Voltage
VEN
Voltage Increasing, On state, Logic High
Voltage Decreasing, Off state, Logic Low
Enable Input Current
V
IEN
Enable Pin Voltage = 0.3 Vmax
Enable Pin Voltage = 1.3 Vmin
Error Flag Voltage Threshold (Fixed Output)
VEF(VT)
91
94
97
% of Vout
Error Flag Output Low Voltage Saturation (IEF = 1.0 mA)
VEF(SAT)
−
200
−
mV
IEF(leakage)
−
1.0
−
mA
tEF
−
50
−
ms
Error Flag Leakage
Error Flag Blanking Time (Note 8)
6. Performance guaranteed over specified operating conditions by design, guard banded test limits, and/or characterization, production tested at
TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
7. Fixed output voltage available at 0.9 V per request.
8. Can be disabled per customer request.
http://onsemi.com
6
NCP5662, NCV5662
TYPICAL CHARACTERISTICS
(Typical characteristics were measured with the same conditions as electrical characteristics, unless otherwise noted)
VDO, DROPOUT VOLTAGE (V)
1.2
1.0
0.8
0.6
0.4
0.2
0
−50
−25
0
25
50
75
100
125
150
TA, AMBIENT TEMPERATURE (°C)
Figure 5. Dropout Voltage vs. Temperature
1.3
Vout = 1.5 V Fixed
Cin = 150 mF
Cout = 10 to 150 mF
TA = 25°C
1.2
1.1
VDO, DROPOUT VOLTAGE (V)
VDO, DROPOUT VOLTAGE (V)
1.3
1.0
0.9
0.8
0.7
0
0.5
1.0
1.5
1.1
1.0
0.9
0.8
0
0.5
1.0
1.5
2.0
Iout, OUTPUT CURRENT (A)
Iout, OUTPUT CURRENT (A)
Figure 6. 1.5 V Dropout Voltage vs. Output Current
Figure 7. 3.3 V Dropout Voltage vs. Output Current
3.5
ISC, SHORT CIRCUIT LIMIT (A)
3.5
IGND, GROUND CURRENT (mA)
1.2
0.7
2.0
Vout = 3.3 V Fixed
Cin = 150 mF
Cout = 10 to 150 mF
TA = 25°C
3.0
2.5
2.0
1.5
1.0
0.5
0
−50
−25
0
25
50
75
100
125
3.25
3
2.75
2.5
2.25
2
−50
150
−25
0
25
50
75
100
125
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 8. Ground Current vs. Temperature
Figure 9. Short Circuit Current Limit vs.
Temperature
http://onsemi.com
7
150
NCP5662, NCV5662
1.6
3.4
1.4
3.0
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
TYPICAL CHARACTERISTICS
1.2
1.0
0.8
0.6
0.4
0.2
0
1.0
Iout = 10 mA
Cin = 150 mF
Cout = 1.0 to 150 mF
TA = 25°C
2.0
3.0
4.0
5.0
6.0
7.0
8.0
2.2
1.8
1.4
9.0
Iout = 10 mA
Cin = 150 mF
Cout = 1.0 to 150 mF
TA = 25°C
1.0
0.6
0.2
0
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
Vin, INPUT VOLTAGE (V)
Vin, INPUT VOLTAGE (V)
Figure 10. 1.5 V Output Voltage vs. Input Voltage
Figure 11. 3.3 V Output Voltage vs. Input Voltage
1.55
3.35
Vin = 3.3 V
Iout = 2.0 A maximum
Cin = 150 mF
Cout = 1.0 to 150 mF
TA = 25°C
1.53
1.51
Vin = 5.1 V
Iout = 2.0 A maximum
Cin = 150 mF
Cout = 1.0 to 150 mF
TA = 25°C
3.34
Vout, OUTPUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE (V)
2.6
1.49
1.47
3.33
3.32
3.31
3.30
3.29
3.28
3.27
3.26
1.45
0
0.5
1.0
1.5
3.25
2.0
1.0
1.5
2.0
Figure 12. 1.5 V Output Voltage vs. Output Load
Current
Figure 13. 3.3 V Output Voltage vs. Output Load
Current
100
RR, RIPPLE REJECTION (dB)
TA = 25°C
L = 25 mm Copper
1.0
OUTPUT CURRENT (A)
0.5
Iout, OUTPUT CURRENT (A)
1.2
0.8
0.6
0.4
0.2
0.0
0
Iout, OUTPUT CURRENT (A)
0
2
4
6
8
10
12
14
16
90
70
60
50
40
30
20
10
0
0
20
Iout = 10 mA
80
INPUT−OUTPUT VOLTAGE DIFFERENTIAL (V)
Figure 14. Output Current vs. Input−Output
Voltage Differential
Vin = 4.0 V
Vout = 0.9 V
Cin = 0 mF
Cout = 1.0 mF
TA = 25°C
1.0
Iout = 1.0 A
10
100
F, FREQUENCY (kHz)
1000
Figure 15. Ripple Rejection vs. Frequency
http://onsemi.com
8
NCP5662, NCV5662
100
100
90
90
NOISE DENSITY (nVrms/ǨHz)
NOISE DENSITY (nVrms/ǨHz)
TYPICAL CHARACTERISTICS
80
70
60
50
40
30
20
10
0
Vin = 12 V
Vout = 0.9 V
Iout = 10 mA
Cin = 150 mF
Cout = 150 mF
TA = 25°C
Start 1.0 kHz
F, FREQUENCY (kHz)
80
70
60
50
40
30
20
10
0
Stop 100 kHz
Vin = 3.3 V
Vout = 0.9 V
Iout = 2.36 A
Cin = 150 mF
Cout = 150 mF
TA = 25°C
Start 1.0 kHz
Figure 16. Noise Density vs. Frequency
F, FREQUENCY (kHz)
Stop 100 kHz
Figure 17. Noise Density vs. Frequency
http://onsemi.com
9
NCP5662, NCV5662
TYPICAL CHARACTERISTICS
Vout
50 mV/Div
Vout
20 mV/Div
Iout
1.0 A/Div
Iout
1.0 A/Div
Vin = 3.3 V
Vout = 1.5 V Fixed
Cin = 150 mF
Cout = 150 mF
TA = 25°C
Iout = 2.0 A to 10 mA
Iout = 10 mA to 2.0 A
TIME (1.0 ms/Div)
TIME (1.0 ms/Div)
Figure 18. Load Transient Response
Figure 19. Load Transient Response
Vin = 3.3 V
Vout = 1.5 V Fixed
Cin = 150 mF
Cout = 150 mF
TA = 25°C
Vout
50 mV/Div
Vout
20 mV/Div
Vin = 3.3 V
Vout = 1.5 V Fixed
Cin = 150 mF
Cout = 150 mF
TA = 25°C
Iout
1.0 A/Div
Iout
1.0 A/Div
Vin = 3.3 V
Vout = 1.5 V Fixed
Cin = 150 mF
Cout = 150 mF
TA = 25°C
Iout = 2.0 A to 10 mA
Iout = 10 mA to 2.0 A
TIME (100 ns/Div)
Figure 21. Load Transient Response
Vin = 4.0 V
Vout = 0.9 V
Cin = 150 mF
Cout = 10 mF
TA = 25°C
Iout = 10 mA to 2.0 A
Vin = 4.0 V
Vout = 0.9 V
Cin = 150 mF
Cout = 10 mF
TA = 25°C
Iout
1.0 A/Div
Iout
1.0 A/Div
Vout
50 mV/Div
Vout
20 mV/Div
TIME (100 ns/Div)
Figure 20. Load Transient Response
Iout = 2.0 A to 10 mA
TIME (200 ns/Div)
TIME (200 ns/Div)
Figure 22. Load Transient Response
Figure 23. Load Transient Response
http://onsemi.com
10
NCP5662, NCV5662
APPLICATION INFORMATION
Current Limit Operation
The NCP5662 is a high performance low dropout 2.0 A
linear regulator suitable for high power applications,
featuring an ultra−fast response time and low noise without
a bypass capacitor. It is offered in both fixed and adjustable
output versions with voltages as low as 0.9 V. Additional
features, such as Enable and Error Flag (fixed output
version) increase the utility of the NCP5662. It is thermally
robust and includes the safety features necessary during a
fault condition, which provide for an attractive high current
LDO solution for server, ASIC power supplies, networking
equipment applications, and many others.
As the peak output current increases beyond its limitation,
the device is internally clampled to 3.0 A, thus causing the
output voltage to decrease and go out of regulation. This
allows the device never to exceed the maximum power
dissipation.
Error Flag Operation
The Error Flag pin on the NCP5662 will produce a logic
Low when it drops below the nominal output voltage. Refer
to the electrical characteristics for the threshold values at
which point the Error Flag goes Low. When the NCP5662
is above the nominal output voltage, the Error Flag will
remain at logic High.
The external pullup resistor needs to be connected
between Vin and the Error Flag pin. A resistor of
approximately 100 kW is recommended to minimize the
current consumption. No pullup resistor is required if the
Error Flag output is not being used.
Input Capacitor
The recommended input capacitor value is a 150 mF
OSCON with an Equivalent Series Resistance (ESR) of
50 mW. It is especially required if the power source is
located more than a few inches from the NCP5662. This
capacitor will reduce device sensitivity and enhance the
output transient response time. The PCB layout is very
important and in order to obtain the optimal solution, the Vin
and GND traces should be sufficiently wide to minimize
noise and unstable operation.
Thermal Consideration
The maximum package power dissipation is:
T
Output Capacitor
P
Proper output capacitor selection is required to maintain
stability. The NCP5662 is guaranteed to be stable at an
output capacitance of, Cout > 10 mF with an ESR between
50 mW and 300 mW over the output current range of 10 mA
to 2.0 A. For PCB layout considerations, place the
recommended ceramic capacitor close to the output pin and
keep the leads short. This should help ensure ultra−fast
transient response times.
The application circuit for the adjustable output version is
shown in Figure 2. The reference voltage is 0.9 V and the
adjustable pin current is typically 40 nA. A resistor divider
network, R1 and R2, is calculated using the following
formula:
Input
Cin
ON
ǒVVout
* 1Ǔ
ref
Vout
Vin
NCP5662
EN
OFF
Enable
J(max)
R
*T
A
qJA
The bipolar process employed for this IC is fully
characterized and rated for reliable 18 V operation. To avoid
damaging the part or degrading it’s reliability, power
dissipation transients should be limited to under 30 W for
D2PAK. For open−circuit to short−circuit transient,
PDTransient = Vin(operating max) * ISC.
Adjustable Output Operation
R1 + R2
D
+
Vout = 0.9 V
Output
Cout
ADJ
GND
Figure 24. To achieve the minimum output voltage,
ADJ to Vout has to be connected together
http://onsemi.com
11
NCP5662, NCV5662
390
340
qJA (°C/W)
290
240
190
140
1 oz Copper
2 oz Copper
90
40
0
100
200
300
400
COPPER AREA
500
600
700
(mm2)
Figure 25. DFN8 Thermal Resistance vs. Copper Area
NCP5662 Evaluation Board
Figure 26. Test Board used for Evaluation
http://onsemi.com
12
NCP5662, NCV5662
ORDERING INFORMATION
Device
NCP5662DSADJR4G
Nominal Output Voltage
Shipping†
D2PAK
800 / Tape & Reel
DFN8
3000 / Tape & Reel
Adj
(Pb−Free)
NCP5662DS12R4G
Fixed, 1.2 V
(Pb−Free)
NCP5662DS15R4G
Fixed, 1.5 V
(Pb−Free)
NCP5662DS18R4G
Fixed, 1.8 V
(Pb−Free)
NCP5662DS25R4G
Fixed, 2.5 V
(Pb−Free)
NCP5662DS28R4G
Fixed, 2.8 V
(Pb−Free)
NCP5662DS30R4G
Fixed, 3.0 V
(Pb−Free)
NCP5662DS33R4G
Fixed, 3.3 V
(Pb−Free)
NCV5662DSADJR4G*
Package
Adj
(Pb−Free)
NCV5662DS15R4G*
Fixed, 1.5 V
(Pb−Free)
NCV5662DS33R4G*
Fixed, 3.3 V
(Pb−Free)
NCP5662MNADJR2G
Adj
(Pb−Free)
NCP5662MN15R2G
Fixed, 1.5 V
(Pb−Free)
NCP5662MN33R2G
Fixed, 3.3 V
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable
http://onsemi.com
13
NCP5662, NCV5662
PACKAGE DIMENSIONS
D2PAK 5−LEAD
CASE 936AA
ISSUE C
A
B
L1
0.10
A
A
E
SEATING
PLANE
M
E1
c2
E/2
B A
M
D1
D
5X
0.13
VIEW A−A
c
e
b
DETAIL C
H
1 2 3 4 5
A
M
B A
M
B
H
SEATING
PLANE
A1
RECOMMENDED
SOLDERING FOOTPRINT*
L
0.424
M
L3
DETAIL C
0.310
0.584
0.136
5X
0.040
0.067
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
14
GAUGE
PLANE
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
FLASH AND GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.005 MAXIMUM PER SIDE. THESE DIMENSIONS
TO BE MEASURED AT DATUM H.
4. THERMAL PAD CONTOUR OPTIONAL WITHIN
DIMENSIONS E, L1, D1, AND E1. DIMENSIONS
D1 AND E1 ESTABLISH A MINIMUM MOUNTING
SURFACE FOR THE THERMAL PAD.
DIM
A
A1
b
c
c2
D
D1
E
E1
e
H
L
L1
L3
M
INCHES
MIN
MAX
0.170
0.180
0.000
0.010
0.026
0.036
0.017
0.026
0.045
0.055
0.325
0.368
0.250
−−−
0.380
0.420
0.200
−−−
0.067 BSC
0.539
0.579
0.058
0.078
−−−
0.066
0.010 BSC
0_
8_
MILLIMETERS
MIN
MAX
4.32
4.57
0.00
0.25
0.66
0.91
0.43
0.66
1.14
1.40
8.25
9.53
6.35
−−−
9.65
10.67
5.08
−−−
1.70 BSC
13.69
14.71
1.47
1.98
−−−
1.68
0.25 BSC
0_
8_
NCP5662, NCV5662
PACKAGE DIMENSIONS
8 PIN DFN, 4x4
CASE 488AF
ISSUE C
A
B
D
PIN ONE
REFERENCE
2X
ÉÉÉ
ÉÉÉ
ÉÉÉ
0.15 C
0.10 C
0.08 C
NOTE 4
DETAIL A
E
OPTIONAL
CONSTRUCTIONS
EXPOSED Cu
DETAIL B
ÇÇÇ
(A3)
A
A1
ÇÇÇ
1
8
e
ÉÉ
ÉÉ
ÇÇ
A3
MOLD CMPD
A1
C
8X
SEATING
PLANE
ALTERNATE
CONSTRUCTIONS
5
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.25
0.35
4.00 BSC
1.91
2.21
4.00 BSC
2.09
2.39
0.80 BSC
0.20
−−−
0.30
0.50
−−−
0.15
SOLDERING FOOTPRINT*
L
4
ÇÇÇ
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
DETAIL B
D2
K
ÇÇ
ÉÉ
TOP VIEW
SIDE VIEW
DETAIL A
NOTES:
1. DIMENSIONS AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30MM FROM TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
5. DETAILS A AND B SHOW OPTIONAL
CONSTRUCTIONS FOR TERMINALS.
L
L1
0.15 C
2X
8X
L
2.21
8X
0.63
E2
8X
b
4.30 2.39
0.10 C A B
0.05 C
PACKAGE
OUTLINE
NOTE 3
BOTTOM VIEW
8X
0.80
PITCH
0.35
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
15
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP5662/D