NCP5504 D

NCP5504, NCV5504
250 mA Dual Output Low
Dropout Linear Regulator
The NCP5504/NCV5504 are dual output low dropout linear
regulators with 2.0% accuracy over the operating temperature range.
They feature a fixed output voltage of 3.3 V (contact factory for other
fixed output voltage options) and an adjustable output that ranges from
1.25 V to 5.0 V. It is available in a 5 pin DPAK Pb−Free package.
The NCP5504/NCV5504 employs an architecture that offers low
noise without a bypass capacitor for the fixed output. This device
along with a ripple rejection of 75 dB and a dropout of 250 mV @
250 mA, suits post−regulation and power sensitive battery−operated
applications.
http://onsemi.com
DPAK−5
DT SUFFIX
CASE 175AA
Features















One Fixed and One Adjustable Output Pin
250 mA Each Output
Adjustable Output Voltage from 1.25 V to 5.0 V
Low Dropout Voltage of 250 mV typical at 250 mA
Low Quiescent Current of 370 mA typical
Ripple Rejection of 75 dB
Temperature Range of NCP5504 −25C to +85C
Temperature Range of NCV5504 −40C to +125C
Low Noise Without Bypass Capacitor; 90 mVrms
Line Regulation < 15 mV
Load Regulation; Vout1 < 15 mV, Vout2 < 10 mV
Accuracy of 2% Overtemperature Range
Thermal Protection and Current Limit
Short Circuit Protection
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These are Pb−Free Devices
MARKING DIAGRAM
5504G
ALYWW
A
L
Y
WW
G
Pin 1. Adjust for Vout
2. Vout2
3. GND
4. Vin
5. Vout1
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
Typical Applications





Audio Visual Equipment
Battery Powered Consumer Products
Instrumentation
Computing and Networking Applications
Automotive Electronics
 Semiconductor Components Industries, LLC, 2013
April, 2013 − Rev. 4
1
Publication Order Number:
NCP5504/D
NCP5504, NCV5504
PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
1
Adjust for Vout2
Description
This pin is connected to the resistor divider on the output. For a 1.25 V output, connect directly
to the Vout2 pin.
2
Vout2
Adjustable Regulated Output Voltage.
3
GND
Power Supply Ground
4
Vin
5
Vout1
Positive Power Supply Input Voltage.
Fixed Regulated Output Voltage. See selector guide for options.
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Input Voltage
Vin
18
V
Operating Input Voltage for Power Considerations
Vin
9.0
V
Output Pin Voltage
Vout
−0.3 to Vin +0.3
V
Adjust Pin Voltage
Vadj
−0.3 to Vin +0.3
Maximum Junction Temperature
NCP5504
NCV5504
TJ
Operating Ambient Temperature
NCP5504
NCV5504
TA
Package Thermal Resistance
Thermal Resistance, Junction−to−Air
Thermal Resistance, Junction−to−Case
125
150
−25C to +85C
−40C to +125C
V
C
C
RqJA
RqJC
100
8
C/W
Storage Temperature Range
Tstg
−55 to +150
C
Electrostatic Discharge Sensitivity
Human Body Model (HBM)
Machine Model (MM)
Charge Device Model (CDM)
ESD
Latchup Performance (JESD78)
Positive
Negative
ILatchup
2000
200
2000
100
100
V
mA
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
http://onsemi.com
2
NCP5504, NCV5504
NCP5504 ELECTRICAL CHARACTERISTICS
(Vin = Vout + 1.0 V, where Vout is the larger of Vout1 or Vout2, TA = 25C, unless otherwise noted)
Characteristic
Symbol
Output Voltage
NCP5504 (TA = −25C to 85C), IO = 250 mA
Min
Typ
Max
Vout
Vout1
Vout2
Adjustable Pin Current
Unit
V
−2%
−2%
3.30
1.25
+2%
+2%
Iadj
−
50
100
nA
Line Regulation (Vout + 1.0 V < Vin < 7.0 V), IO = 250 mA
Regline
−
5
15
mV
Load Regulation (1.0 mA < IO< 250 mA) for Vout1
Load Regulation (1.0 mA < IO < 250 mA) for Vout2
Regload
−
10
5
15
10
mV
mV
VDO
−
250
400
mV
−
−
75
60
−
−
Dropout Voltage (IO = 250 mA)
Ripple Rejection Ratio (IO = 250 mA)
RR
120 Hz
1 kHz
dB
Quiescent Current (IO1, IO2 = 0 mA)
Iq
−
370
450
mA
Fixed Output Noise Voltage (10 Hz − 100 kHz Vout = 3.3 V,
IO = 100 mA, CO = 1.0 mF)
Vn
−
90
−
mVrms
Ground Current (IO1, IO2 = 250 mA)
Ignd
−
10
20
mA
TJmax
150
165
−
C
Ilim
350
450
−
mA
Thermal Shutdown (Guaranteed by design)
Current Limit on Vout1 and Vout2
NCV5504 ELECTRICAL CHARACTERISTICS
(Vin = Vout + 1.0 V, where Vout is the larger of Vout1 or Vout2, −40C  TJ  150C, −40C  TA  125C, unless otherwise noted)
Symbol
Characteristic
Output Voltage
NCV5504, IO = 250 mA
Min
Typ
Max
Vout
Vout1
Vout2
Unit
V
−2%
−2%
3.30
1.25
+2%
+2%
Iadj
−
50
100
nA
Line Regulation (Vout + 1.0 V < Vin < 7.0 V), IO = 250 mA
Regline
−
5
15
mV
Load Regulation (1.0 mA < IO< 250 mA) for Vout1
Load Regulation (1.0 mA < IO < 250 mA) for Vout2
Regload
−
10
5
15
10
mV
mV
VDO
−
250
400
mV
−
−
75
60
−
−
Adjustable Pin Current
Dropout Voltage (IO = 250 mA)
Ripple Rejection Ratio (IO = 250 mA)
RR
120 Hz
1 kHz
dB
Quiescent Current (IO1, IO2 = 0 mA)
Iq
−
370
450
mA
Fixed Output Noise Voltage (10 Hz − 100 kHz Vout = 3.3 V,
IO = 100 mA, CO = 1.0 mF)
Vn
−
90
−
mVrms
Ground Current (IO1, IO2 = 250 mA)
Ignd
−
10
20
mA
TJmax
150
165
−
C
Ilim
320
450
−
mA
Thermal Shutdown (Guaranteed by design)
Current Limit on Vout1 and Vout2
http://onsemi.com
3
NCP5504, NCV5504
NCP5504/
NCV5504
NCP5504/
NCV5504
Adj Vout2 GND Vin Vout1
1 2 3 4 5
Adj Vout2 GND Vin Vout1
1 2 3 4 5
Vout1
Vin
Cout2
Cin
Vout1
Vin
Vout2
Cn
Cout1
Vout2
R2
Cout2
Cin
Cout1
R1
GND
GND
Figure 1. Application Schematic, Fixed Output
Version. Vout1 = 3.3 V, Vout2 = 1.25 V
NOTE:
Figure 2. Application Schematic, Adjustable
Version. Vout1 = 3.3 V, Vout2 = 1.25 V to 5.0 V, Where
Vout2 = 1.25 V * (1+R2/R1)
Please note that in order to maintain high accuracy on the adjustable output (Vout2), use R1 values < 30 kW in the
resistor divider. The recommended capacitor type and values are as follows:
Cin (Tantalum or Aluminum Electrolytic) = 4.7 mF to 100 mF
Cout1, Cout2 = Low ESR, 1.0 mF to 22 mF
Cn = 200 pF to 1.0 nF.
http://onsemi.com
4
NCP5504, NCV5504
TYPICAL CHARACTERISTICS
1.30
Vin = 4.3 V
3.295
Vin = 4.3 V
Vout2, OUTPUT VOLTAGE (V)
Vout1, OUTPUT VOLTAGE (V)
3.30
3.29
3.285
3.28
3.275
3.27
3.265
3.26
0
50
100
150
200
250
1.28
1.26
1.24
1.22
1.20
0
50
Iout, OUTPUT CURRENT (mA)
200
250
Figure 4. Output Voltage vs. Output Load
Current for Vout2
16
300
IO1 = 250 mA
IGND, GROUND CURRENT (mA)
VDO, DROPOUT VOLTAGE (mV)
150
Iout, OUTPUT CURRENT (mA)
Figure 3. Output Voltage vs. Output Load
Current for Vout1
250
200
150
100
50
0
−40
100
−20
0
20
40
60
80
100
12
10
8
6
4
2
0
−40
120
IO1 = IO2 = 250 mA
14
−20
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (C)
TJ, JUNCTION TEMPERATURE (C)
Figure 5. Dropout Voltage vs. Temperature for Vout1
http://onsemi.com
5
Figure 6. Ground Current vs. Temperature
120
NCP5504, NCV5504
450
450
400
Ilim, SHORT CIRCUIT LIMIT (mA)
500
400
350
300
250
200
150
100
50
RR, RIPPLE REJECTION (dB)
0
−40
−20
0
20
40
60
80
100
350
300
250
200
150
100
50
0
−40
120
90
80
70
60
IO = 10 mA
50
10
0
0.1
40
60
80
100
Figure 8. Short Circuit Current Limit vs.
Temperature for Vout2
100
20
20
Figure 7. Short Circuit Current Limit vs.
Temperature for Vout1
90
30
0
TJ, JUNCTION TEMPERATURE (C)
100
40
−20
TJ, JUNCTION TEMPERATURE (C)
RR, RIPPLE REJECTION (dB)
Iim, SHORT CIRCUIT LIMIT (A)
TYPICAL CHARACTERISTICS
Vin = 5.0 V
Vout1 = 3.3 V
Cin = 4.7 mF
Cout = 1.0 mF
TJ = 25C
1.0
IO = 250 mA
10
100
1000
120
80
70
60
IO = 10 mA
50
40
30
20
10
0
0.1
F, FREQUENCY (kHz)
Vin = 5.0 V
Vout2 = 1.25 V
Cin = 4.7 mF
Cout = 1.0 mF
TJ = 25C
1.0
IO = 250 mA
10
100
1000
F, FREQUENCY (kHz)
Figure 9. Ripple Rejection vs. Frequency for
Vout1
Figure 10. Ripple Rejection vs. Frequency for
Vout2
http://onsemi.com
6
NCP5504, NCV5504
TYPICAL CHARACTERISTICS
600
Vin = 5.0 V
Vout1 = 3.3 V
IO = 10 mA
Cin = 4.7 mF
Cout = 4.7 mF
TA = 25C
500
400
300
200
100
0
START: 100 Hz
NOISE DENSITY (nVrms/ǨHz)
NOISE DENSITY (nVrms/ǨHz)
600
400
300
200
100
0
STOP: 100 kHz
Vin = 5.0 V
Vout1 = 3.3 V
IO = 250 mA
Cin = 4.7 mF
Cout = 4.7 mF
TA = 25C
500
START: 100 Hz
Figure 11. Noise Density vs. Frequency
Figure 12. Noise Density vs. Frequency
250
Vin = 5.0 V
Vout2 = 1.25 V
IO = 10 mA
Cin = 4.7 mF
Cout = 4.7 mF
TA = 25C
250
200
150
100
50
START: 100 Hz
NOISE DENSITY (nVrms/ǨHz)
NOISE DENSITY (nVrms/ǨHz)
300
0
STOP: 100 kHz
200
150
50
0
STOP: 100 kHz
Vin = 5.0 V
Vout2 = 1.25 V
IO = 250 mA
Cin = 4.7 mF
Cout = 4.7 mF
TA = 25C
100
START: 100 Hz
Figure 13. Noise Density vs. Frequency
STOP: 100 kHz
Figure 14. Noise Density vs. Frequency
http://onsemi.com
7
NCP5504, NCV5504
Vout
100 mV/Div
IO = 10 mA to 250 mA
IO = 1.0 mA to 250 mA
TIME (100 mS/Div)
Figure 15. Load Transient Response for Vout1
Figure 16. Load Transient Response for Vout1
Vout
50 mV/Div
TIME (100 mS/Div)
Vin = 5.0 V
Vout2 = 1.25 V
Cin = 4.7 mF
Cout = 4.7 mF
TA = 25C
IO = 10 mA to 250 mA
IO
100 mA/Div
IO
100 mA/Div
Vin = 5.0 V
Vout1 = 3.3 V
Cin = 4.7 mF
Cout = 4.7 mF
TA = 25C
IO
100 mA/Div
Vin = 5.0 V
Vout1 = 3.3 V
Cin = 4.7 mF
Cout = 4.7 mF
TA = 25C
Vout
50 mV/Div
IO
100 mA/Div
Vout
100 mV/Div
TYPICAL CHARACTERISTICS
TIME (100 mS/Div)
IO = 1.0 mA to 250 mA
TIME (100 mS/Div)
Figure 18. Load Transient Response for Vout2
Vin
1.0 V/Div
Vin
1.0 V/Div
Figure 17. Load Transient Response for Vout2
DVin = 1.0 V
Vout1 = 3.3 V
IO = 250 mA
Tr = Tf = 1.0 ms
Cout = 4.7 mF
TA = 25C
Vout
50 mV/Div
Vout
50 mV/Div
Vin = 5.0 V
Vout2 = 1.25 V
Cin = 4.7 mF
Cout = 4.7 mF
TA = 25C
TIME (40 mS/Div)
DVin = 1.0 V
Vout2 = 1.25 V
IO = 250 mA
Tr = Tf = 1.0 ms
Cout = 4.7 mF
TA = 25C
TIME (40 mS/Div)
Figure 19. Line Transient Response for Vout1
Figure 20. Line Transient Response for Vout2
http://onsemi.com
8
NCP5504, NCV5504
APPLICATION INFORMATION
Introduction
will reduce device sensitivity and enhance the output
transient response time. The PCB layout is very important
and in order to obtain the optimal solution, the Vin and GND
traces should be sufficiently wide to minimize noise and
unstable operation.
For the adjustable output pin, Cn ranges from 200 pF and
1.0 nF.
The output capacitor range is between 1.0 mF and 22 mF.
For PCB layout considerations, place the capacitor close to
the output pin and keep the leads short.
The NCP5504/NCV5504 are high performance dual
output, 250 mA linear regulators suitable for post regulation
and power sensitive battery−operated applications. They
feature 2.0% accuracy over the operating temperature
range. With one fixed output voltage at 3.3 V, and one
adjustable output voltage ranging from 1.25 V to 5.0 V, the
dropout voltage is 250 mV typical. Additional features, such
as an architecture that allows for low noise on the fixed
output without a bypass capacitor, provides for an attractive
LDO solution for audio visual equipment, instrumentation,
computing and networking applications, and automotive
electronics. It is thermally robust and is offered in a 5 pin
DPAK Pb−Free package.
Adjustable Output Operation
The application circuit for the adjustable output version is
shown in Figure 2. Vout2 is calculated based on the following
equation:
Capacitor Selection
ǒ
Ǔ
Vout2 + 1.25 V * 1 ) R2
R1
The recommended input capacitor types are tantalum and
aluminum electrolytic ranging from 4.7 mF to 100 mF. It is
especially required if the power source is located more than
a few inches from the NCP5504/NCV5504. This capacitor
In order to maintain high accuracy on the adjustable
output, R1 values should be < 30 kW.
ORDERING INFORMATION
Package
Shipping†
NCP5504DTRKG
DPAK
(Pb−Free)
2500 / Tape and Reel
NCV5504DTRKG*
DPAK
(Pb−Free)
2500 / Tape and Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable
http://onsemi.com
9
NCP5504, NCV5504
PACKAGE DIMENSIONS
DPAK 5, CENTER LEAD CROP
CASE 175AA
ISSUE A
−T−
C
B
V
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
SEATING
PLANE
E
R
R1
Z
A
S
DIM
A
B
C
D
E
F
G
H
J
K
L
R
R1
S
U
V
Z
12 3 4 5
U
K
F
J
L
H
D
G
5 PL
0.13 (0.005)
M
INCHES
MIN
MAX
0.235 0.245
0.250 0.265
0.086 0.094
0.020 0.028
0.018 0.023
0.024 0.032
0.180 BSC
0.034 0.040
0.018 0.023
0.102 0.114
0.045 BSC
0.170 0.190
0.185 0.210
0.025 0.040
0.020
−−−
0.035 0.050
0.155 0.170
MILLIMETERS
MIN
MAX
5.97
6.22
6.35
6.73
2.19
2.38
0.51
0.71
0.46
0.58
0.61
0.81
4.56 BSC
0.87
1.01
0.46
0.58
2.60
2.89
1.14 BSC
4.32
4.83
4.70
5.33
0.63
1.01
0.51
−−−
0.89
1.27
3.93
4.32
T
SOLDERING FOOTPRINT*
6.4
0.252
2.2
0.086
0.34 5.36
0.013 0.217
5.8
0.228
10.6
0.417
0.8
0.031
SCALE 4:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP5504/D