TRK-MPC5634M Quick Start Guide

Quick Start Guide for TRK-MPC5634M
TRK-MPC5634M
Automotive powertrain and precision
timed industrial applications
Starter TRAK
Starter TRAK
Get to Know the TRK-MPC5634M
MPC5634M
LIN Connectors
LEDs
USB Connector/
Power Supply
DIP Switches
Buttons
MCZ3390S5EK
System Basis Chip
Potentiometer
CAN
All Available Pins
eSCI (footprint)
Photocell Sensor
JTAG
Figure 1: TRK-MPC5634M Board
TRK-MPC5634M
Freescale StarterTRAK
The TRK-MPC5634M board is part of the Freescale StarterTRAK series, a
development platform that enables rapid prototyping and tool re-use. Take your
design to the next level and begin constructing with your StarterTRAK system today.
Starter TRAK
Quick Start Guide for TRK-MPC5634M
TRK-MPC5634M Features
• TRK-MPC5634M series microcontroller
(144-pin LQFP)
• On-board JTAG connection via open
source OSBDM circuit using the
MPC9S08JM microcontroller
See pemicro.com/osbdm for
source code
• MCZ3390S5EK system basis chip
with advanced power management
and integrated CAN tranciever and
LIN 2.0 interface
• CAN interface(s)
• LIN interface(s)
• Analog interface with potentiometer
• High-efficiency LEDs
• SCI serial communication interfaces
Step-by-Step Installation Instructions
In this Quick Start Guide, you will learn how to set up the TRK-MPC5634M
board and use eTPU timers and ADC to drive LEDs exercise.
STEP
1
Install Software
and Tools
•Install CodeWarrior Development
Studio for 55xx/56xx Architectures v2.7
or later
•Install RAppID initialization tool
Install in the order listed. These programs are
included on the DVD. CodeWarrior and RAppID
included offers a 30-day evaluation license. For
updates, please visit freescale.com/StarterTRAK.
Starter TRAK
STEP
2
Connect the USB Cable
Connect one end of the USB
cable to the PC and the other end to the
mini-B connector on the TRK-MPC5634M
board. Allow the PC to automatically
configure the USB drivers if needed.
STEP
3
Open Supporting
Documentation
Open the MPC5500 and MPC5600
Simple Cookbook and TRK-MPC5634M
User Manual from the Documentation and
Training tab on the included DVD.
STEP
Explore Further with the
MPC5500 and MPC5600
Simple Cookbook: Using eTPU
timers and ADC to drive LEDs
4
To run a demonstration using the
TRK-MPC5634M, follow the instructions
for the eTPU timer and ADC lab exercise
for MPC5634M in the MPC5500 and
MPC5600 Simple Cookbook. The
supplemental application note AN4266
for TRK-MPC5634M will also need to be
followed since the Simple Cookbook does
not contain all the code example required.
The Cookbook and AN4266 is located
under the documentation tab on the DVD.
STEP
5
Learn More About the
MPC5634M
Read the release notes and documentation
located on the DVD and at
freescale.com/StarterTRAK.
• The MPC5500 and MPC5600 Simple
Cookbook provides simple code
examples for manipulating different
peripherals on the MPC5634M
• The RAppID graphical initialization
software will help you get to market
faster
• CodeWarrior for 55xx/56xx with
examples from the Simple Cookbook
Note: Check freescale.com/TRK-MPC5634M for
the latest training and labs.
Starter TRAK
Quick Start Guide for TRK-MPC5634M
TRK-MPC5634M Jumper Options
The following is a list of all jumper options.
Jumper
Option
J1
System Power Source
Select
J2
SBC I/O LED
Pull Up/Down
J3
SBC I/O Signal
J4
J5
J6
SBC DBG Short
to GND
(default: OFF)
SBC DBG Pull Up
(default: OFF)
CAN Signals to
Transceiver Enable
J7
RS232 TXD Signal
J8
RS232 RXD Signal
J9
J10
J11
J12
CT7
LIN1 VBus Enable
(default: OFF)
LIN0 VBus Enable
(default: OFF)
LIN0 Signals to
Connector Enable
LIN1 Signals to
Connector Enable
(default: OFF)
LIN TXD Signal
Setting
Description
1-2 (default)
2-3
1-2 (default)
2-3
1-2 (default)
2-3
USB OSJTAG Supplies 5VDC
SBC MC33905 Supplies 5VDC
Pull Up
Pull Down
I/O-0
I/O-1
1-2
Short SBC DBG Pin to GND, Bypass R21 and D13
1-2
Pull Up SBC DBG Pin to SBC Power Supply via 330 Ohm
Resistor
1-2, 3-4 (default)
Enables TXD and RXD signals to CAN Transceiver
1-2 (default)
2-3
1-2 (default)
2-3
MCU TXD to Virtual Serial Port
MCU TXD to RS232 Transceiver
MCU RXD to Virtual Serial Port
MCU RXD to RS232 Transceiver
1-2
Provides Power to LIN1 Connector
1-2
Provides Power to LIN0 Connector
1-2 (default),
3-4 (default)
Connects LIN0 Signals to LIN0 Connector
1-2, 3-4
Connects LIN1 Signals to LIN1 Connector
1-2 (default)
2-3
MCU LIN0TX to Transceiver
MCU LIN1TX to Transceiver
Starter TRAK
TRK-MPC5634M Jumper Options (continued from previous page)
Jumper
Option
CT8
LIN RXD Signal
CT1
Cut Trace
J16
SBC SPI
Setting
1-2 (default)
2-3
Shorted (default)
Cut traces on PCB
board:
Description
MCU LIN0RX to Transceiver
MCU LIN1RX to Transceiver
Provides Power to MCU; Current Measurement
1-2 (default)
3-4(default)
Connects MCU SPI signals to SBC SPI
5-6(default)
7-8(default)
CT4
CT5
J23
J24
J25
J26
External Crystal
Circuitry Enable
Cut Trace (default:
ALL ON)
External Crystal
Circuitry Enable Cut
Trace
(default: ALL ON)
External Oscillator via
SMA Enable
(default: OFF)
Push Button Active
High or Low; Opposite
of J25
Push Button Pull
Up/Down Enable;
Opposite of J24
Push Button Signals
Enable (default:
ALL ON)
shorted (default)
XTAL
shorted (default)
EXTAL
1-2
EXTAL
1-2 (default)
Active Low
2-3
Active High
1-2 (default)
Pull Up
2-3
Pull Down
1-2 (default),
3-4 (default),
5-6 (default),
7-8 (default)
Connects MCU Port EMIOS0, EMIOS2, EMIOS4, and EMIOS8 to
Push Buttons Correspondingly
Starter TRAK
Quick Start Guide for TRK-MPC5634M
TRK-MPC5634M Jumper Options (continued from previous page)
Jumper
J27
J28
J29
J30
J31
J32
J33
CT9
J35
Option
LED Signals Enable
(default: ALL ON)
DIL Switch Signals
Enable
(default: ALL ON)
DIL Switch Active
High or Low
Analog Input Enable
Photo Sensor Enable
SBC Reset to MCU
Enable (default: OFF)
OSJTAG Reset to MCU
Enable
System Reset Enable
OSJTAG Bootloader
Enable
(default: OFF)
J37
BOOTCFG1
J38
PLLREF
CT2
WKPCFG
Setting
1-2 (default),
3-4 (default),
5-6 (default),
7-8 (default)
1-2 (default),
3-4 (default),
5-6 (default),
7-8 (default)
1-2 (default)
2-3
1-2 (default)
1-2 (default)
Description
Connects MCU Port EMIOS9, EMIOS10, EMIOS11, and
EMIOS12 to LEDs Correspondingly
Connects MCU Port eTPUA20, eTPUA21, eTPUA22, and
eTPUA23 to DIL Switch Correspondingly
Active High
Active Low
Connects MCU AN17 to Potentiometer
Connects MCU AN35 to Photo Cell
1-2
Enables SBC Reset Signal to Trigger MCU Reset
1-2 (default)
Enables OSJTAG Reset Signal to Trigger MCU Reset
1-2 (default)
Connects Reset Sources to MCU Reset Signal
1-2
Forces OSJTAG to start up in bootloader mode for firmware
updates
1-2
2-3 (default)
1-2 (default)
2-3
1-2 (default)
2-3
Processor uses serial boot mode
Processor uses internal boot mode
Processor uses a crystal clock source
Processor uses an external clock source
Processor pins are configured as weak pull down
Processor pins are configured as weak pull up
Starter TRAK
To learn more, please visit freescale.com/StarterTRAK.
Freescale, the Freescale logo and CodeWarrior are trademarks of
Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other
product or service names are the property of their respective owners.
© 2011 Freescale Semiconductor, Inc.
Doc Number: MPC5634MQSG / REV 0
Agile Number: 926-78590 / REV A