Quick Start Guide for TRK-MPC5604B TRK-MPC5604B Automotive body and industrial applications Starter TRAK Starter TRAK Get to Know the TRK-MPC5604B MPC5604B LIN Connectors LEDs USB Connector/ Power Supply Switches Potentiometer MCZ3390S5EK System Basis Chip All Available Pins CAN RS232 Figure 1: TRK-MPC5604B Board* TRK-MPC5604B Freescale StarterTRAK The TRK-MPC5604B board is part of the Freescale StarterTRAK series, a development platform that enables rapid prototyping and tool re-use. Take your design to the next level and begin constructing with your StarterTRAK system today. * Graphic subject to change Starter TRAK Quick Start Guide for TRK-MPC5604B TRK-MPC5604B Features • MPC560xB/C series microcontroller (144-pin LQFP) • On-board JTAG connection via open source OSBDM circuit using the MPC9S08JM microcontroller See pemicro.com/osbdm for source code • MCZ3390S5EK system basis chip with advanced power management and integrated CAN tranciever and LIN 2.0 interface • CAN interface • LIN interface • Analog interface with potentiometer • High-effieiency LEDs • SCI serial communication interface Step-by-Step Installation Instructions In this Quick Start Guide, you will learn how to set up the TRK-MPC5604B board and run the default low-power lab exercise. STEP 1 Install Software and Tools •Install CodeWarrior Development Studio for 55xx/56xx Architectures v2.7 or later •Install RAppID initialization tool Install in the order listed. These programs are included on the DVD. CodeWarrior and RAppID included offers a 30-day evaluation license. For updates, please visit freescale.com/StarterTRAK. Starter TRAK STEP 2 Connect the USB Cable Connect one end of the USB cable to the PC and the other end to the mini-B connector on the TRK-MPC5604B board. Allow the PC to automatically configure the USB drivers if needed. STEP 3 Open Supporting Documentation Open the MPC5500 and MPC5600 Simple Cookbook and TRK-MPC5604B User Manual from the Documentation and Training tab on the included DVD. STEP Explore Further with the MPC5500 and MPC5600 Simple Cookbook: Low-Power Lab Exercise 4 To run a demonstration using the TRK-MP5604B, follow the instructions for the low power lab exercise for MPC560xB in the MPC5500 and MPC5600 Simple Cookbook. The Cookbook is located under the documentation tab on the DVD. STEP 5 Learn More About the MPC5604B Read the release notes and documentation located on the DVD and at freescale.com/StarterTRAK. • The MPC5500 and MPC5600 Simple Cookbook provides simple code examples for manipulating different peripherals on the MPC5604B • The RAppID graphical initialization software will help you get to market faster • CodeWarrior for 55xx/56xx with examples from the Simple Cookbook Note: The lab exercise to use low power is located on p.110 in section 13.3.1. Check freescale.com/ TRK-MPC5604B for the latest training and labs. Quick Start Guide for TRK-MPC5604B Starter TRAK TRK-MPC5604B Jumper Options The following is a list of all jumper options. Jumper J1 Option System Power Setting Description 1-2 External Power 9V DC to 12V DC Regulated Down to 5V DC 3-4 USB OSBDM Supplies 5V DC 5-6 SBC33905 Supplies 5V DC 1-2 Pull Up 2-3 Pull Down 1-2 I/O-0 2-3 I/O-1 J2 SBC I/O LED Pull Up/ Down J3 SBC I/O Signal J4 SBC DBG Short to GND 1-2 Short SBC DBG Pin to GND, Bypass R21 and D11 J5 SBC DBG Pull Up 1-2 Pull Up SBC DBG Pin to SBC Power Supply via 330 Ohm Resistor J6 CAN Signals to Transceiver Enable 1-2, 3-4 Enables TXD and RXD signals to CAN Transceiver 1-2 MCU TXD to Virtual Serial Port 2-3 MCU TXD to RS232 Transceiver 1-2 MCU RXD to Virtual Serial Port 2-3 MCU RXD to RS232 Transceiver J7 RS232 TXD Signal J8 RS232 RXD Signal J9 LIN1 VBus Enable 1-2 Provides Power to LIN1 Connector J10 LIN0 VBus Enable 1-2 Provides Power to LIN0 Connector J11 LIN0 Signals to Connector Enable 1-2, 3-4 Connects LIN0 Signals to LIN0 Connector J12 LIN1 Signals to Connector Enable 1-2, 3-4 Connects LIN1 Signals to LIN1 Connector Starter TRAK TRK-MPC5604B Jumper Options (continued from previous page) Jumper J13 Option LIN TXD Signal Setting Description 1-2 MCU LIN0TX to Transceiver 2-3 MCU LIN1TX to Transceiver 1-2 MCU LIN0RX to Transceiver 2-3 MCU LIN1RX to Transceiver J14 LIN RXD Signal J15 MCU VDD Enable 1-2 Provides Power to MCU, Current Measurement J16 VDD_BV Enable 1-2 Provides Power to VDD_BV 1-2 FAB Pulled Up High 2-3 FAB Pulled Down Low 1-2 ABS Pulled Up High 2-3 ABS Pulled Down Low J17 FAB J18 ABS J19 MPC5604B/ MPC5607B for Pin 81 1-2 MPC5604B PB11 2-3 MPC5607B VSSA J20 MPC5604B/ MPC5607B for Pin 82 1-2 MPC5604B PD12 2-3 MPC5607B VDDA J21 VDDA Enable 1-2 Provides Power to VDDA, Current Measurement J22 External Crystal Circuitry Enable 1-2 XTAL 2-3 EXTAL J23 External Oscillator via SMA Enable 1-2 EXTAL J24 Push Button Active High or Low, Opposite of J25 1-2 Active Low 2-3 Active High J25 Push Button Pull Up/Down Enable, Opposite of J24 1-2 Pull Up 2-3 Pull Down Quick Start Guide for TRK-MPC5604B Starter TRAK TRK-MPC5604B Jumper Options (continued from previous page) Jumper Option Setting Description J26 Push Button Signals Enable 1-2, 3-4, 5-6, 7-8 Connects MCU Port A2, A4, G3 and G5 to Corresponding Push Buttons J27 LED Signals Enable 1-2, 3-4, 5-6, 7-8 Connects MCU Port G10, G11, G12 and G13 to Corresponding LEDs J28 DIL Switch Signals Enable 1-2, 3-4, 5-6, 7-8 Connects MCU Port G6, G7, G8 and G9 to Corresponding DIL Switch J29 DIL Switch Active High or Low 1-2 Active High 2-3 Active Low J30 Analog Input Enable 1-2 Connects MCU ANP0 to Potentiometer J31 Photo Sensor Enable 1-2 Connects MCU ANP1 to Photo Cell J32 SBC Reset to MCU Enable 1-2 Enables SBC Reset Signal to Trigger MCU Reset J33 OSBDM Reset to MCU Enable 1-2 Enables OSBDM Reset Signal to Trigger MCU Reset J34 System Reset Enable 1-2 Connects Reset Sources to MCU Reset Signal J35 OSBDM IRQ Enable 1-2 Enables OSBDM to generate an Interrupt Starter TRAK To learn more, please visit freescale.com/StarterTRAK. Freescale, the Freescale logo and CodeWarrior are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are the property of their respective owners. © 2010 Freescale Semiconductor, Inc. Doc Number: MPC5604BQSG / REV 0 Agile Number: 926-26780 / REV A