LT3598 - 6-String 30mA LED Driver with ±1.5% Current Matching

LT3598
6-String 30mA LED Driver
with ±1.5% Current Matching
DESCRIPTION
FEATURES
n
n
n
n
n
n
n
n
n
n
n
n
n
n
True Color PWM™ Dimming Delivers Up to 3000:1
Dimming Ratio
Drives Six Strings of LEDs at Up to 30mA
±1.5% Accurate LED Current Matching
Wide Input Voltage Range: 3.2V to 30V
Output Voltage Up to 44V
Regulates Current Even When VIN > VOUT
Disconnects LEDs in Shutdown
Programmable Open LED Protection (Regulated)
OPENLED Alert Pin
Programmable LED Current Derating
Adjustable Frequency: 200kHz to 2.5MHz
Synchronizable to an External Clock
Parallel Channels for Higher Current per LED String
Thermally Enhanced 4mm × 4mm QFN and 24-Lead
TSSOP Packages
APPLICATIONS
n
n
n
The LT®3598 is a fixed frequency step-up DC/DC converter
designed to drive up to six strings of LEDs at an output
voltage up to 44V. LED dimming can be achieved with
analog dimming on the CTRL pin, and with pulse width
modulation dimming on the PWM pin. The LT3598
accurately regulates LED current even when the input
voltage is higher than the LED output voltage. The switching
frequency is programmable from 200kHz to 2.5MHz
through an external resistor.
Additional features include programmable overvoltage
protection, switching frequency synchronization to an
external clock, LED current derating based on junction
temperature and/or LED temperature, LED string disable
control, OPENLED alert pin and output voltage limiting
when all LED strings are disconnected. The LT3598 is
available in a thermally enhanced 24-lead (4mm × 4mm)
QFN and 24-lead TSSOP packages.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. True Color PWM is a trademark of Linear Technology Corporation.
All other trademarks are the property of their respective owners. Protected by U.S. Patents
including 7199560, 7321203.
Notebook Computer Display
Medium Size Displays
Automotive LCD Display
TYPICAL APPLICATION
LED Current Matching
90% Efficient LED Driver for 60 White LEDs
PVIN
8V TO 40V
10μH
2.2μF
1.5
SW
1.00M
100k
OPENLED
SHDN
SHDN
PWM
PWM
SYNC
SYNC
FB
30.9k
LT3598
RT
51.1k
ALL SIX LED STRINGS
1.0
VO_SW
VIN
MATCHING (%)
VIN
5V
2.2μF
4.7μF
VOUT
0.5
0
–0.5
–1.0
VREF
10k
CTRL
100k
TSET ISET SS
60.4k
47pF
100k
14.7k
–1.5
–50
LED1
LED2
LED3
LED4
LED5
LED6
GND VC
10nF
–25
0
25
50
75
100
125
TEMPERATURE (°C)
20mA
3598 TA01b
2.61k
15nF
3598 TA01a
3598fb
1
LT3598
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
(Note 1)
SHDN ................................................................VIN + 3V
VIN, OPENLED ...........................................................30V
SW Voltage ...............................................................45V
VOUT, VO_SW Voltage .................................................44V
LED1 to LED6............................................................44V
PWM, SYNC, CTRL, RT, SS, VC ...................................6V
VREF, FB Voltage..........................................................6V
ISET, TSET.....................................................................6V
Operating Junction Temperature Range
(Note 2)..................................................–40°C to 125°C
Maximum Junction Temperature........................... 125°C
Storage Temperature Range...................–65°C to 150°C
TOP VIEW
VO_SW
TOP VIEW
22 GND
LED1
4
21 VREF
LED1 1
18 VREF
20 SS
LED2 2
17 SS
19 RT
LED3 3
OPENLED 10
16 NC
15 TSET
ISET 11
14 FB
CTRL 12
13 VC
FE PACKAGE
24-LEAD PLASTIC TSSOP
TJMAX = 125°C, θJA = 38°C/W
EXPOSED PAD (PIN 25) IS PGND, MUST BE SOLDERED TO PCB
14 SYNC
LED6 6
13 NC
7
8
9 10 11 12
TSET
9
17 SYNC
15 PWM
LED5 5
FB
LED6
8
18 PWM
16 RT
25
LED4 4
VC
LED5
7
25
CTRL
LED4
6
ISET
LED3
5
24 23 22 21 20 19
OPENLED
LED2
GND
3
SHDN
23 SHDN
VO_SW
VIN
24 VIN
2
SW
1
VOUT
SW
VOUT
UF PACKAGE
24-LEAD (4mm s 4mm) PLASTIC QFN
TJMAX = 125°C, θJA = 37°C/W
EXPOSED PAD (PIN 25) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3598EUF#PBF
LT3598EUF#TRPBF
3598
24-Lead (4mm × 4mm) Plastic QFN
–40°C to 125°C
LT3598IUF#PBF
LT3598IUF#TRPBF
3598
24-Lead (4mm × 4mm) Plastic QFN
–40°C to 125°C
LT3598EFE#PBF
LT3598EFE#TRPBF
LT3598
24-Lead Plastic TSSOP
–40°C to 125°C
LT3598IFE#PBF
LT3598IFE#TRPBF
LT3598
24-Lead Plastic TSSOP
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
3598fb
2
LT3598
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 5V, VSHDN = VIN unless otherwise noted. (Note 2)
PARAMETER
CONDITIONS
MIN
Minimum Operating Voltage
TYP
MAX
3
3.2
V
30
V
1.230
1.260
1.260
V
V
0.01
0.03
%/V
Maximum Operating Voltage
Reference Voltage
l
1.216
1.210
Reference Voltage Line Regulation
3.2V < VIN < 30V, VC = 0.3V
Maximum VREF Pin Current
Out of Pin
FB Pin Bias Current
VFB = 1.230V (Note 3)
100
FB Error Amp Transconductance
ΔI = 5μA
300
200
FB Error Amp Voltage Gain
μA
250
1.22
1.24
nA
μmhos
600
FB Pin Voltage
UNITS
V/V
1.26
V
Current Loop Amp Transconductance
21
μmhos
Current Loop Amp Voltage Gain
80
V/V
VC Sink Current
10
μA
Quiescent Current
VSHDN = 5V, PWM = 0V, Not Switching
Quiescent Current in Shutdown
VSHDN = 0V
ISET Voltage
VCTRL = 1.5V, VTSET = 1.5V, RISET = 14.7kΩ
LED Current
RISET = 14.7kΩ
LED String Current Matching
20mA LED Current
3.5
5
mA
0
1
μA
0.985
1.000
1.015
V
19.5
20
20.7
mA
±0.5
±1.5
%
0.2
0.25
l
LED Open Detection Threshold
OPENLED Sink Current
2
Minimum LED Regulation Voltage
V
mA
0.8
V
LED1-6 Leakage Current
VLED1-6 = 1V, VOUT = 5V, PWM = 0V
VLED1-6 = 42V, VOUT = 44V, PWM = 0V
0.1
0.2
1
2
μA
μA
CTRL Pin Bias Current
VCTRL = 0.8V (Note 4)
50
125
nA
Switching Frequency
RT = 309kΩ
RT = 51.1kΩ
RT = 14.7kΩ
171
0.9
2.25
190
1
2.5
209
1.1
2.75
kHz
MHz
MHz
602
mV
Maximum Switch Duty Cycle
RT = 309kΩ
RT = 51.1kΩ
RT = 14.7kΩ
90
87
80
95
90
86
%
%
%
Switch Current Limit
(Note 5)
1.5
2
Switch VCESAT
ISW = 0.5A
0.12
Switch Leakage Current
VSW = 40V
0.2
TSET Voltage
l
2.5
A
V
5
μA
3598fb
3
LT3598
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 5V, VSHDN = VIN unless otherwise noted. (Note 2)
PARAMETER
CONDITIONS
SHDN Pin Current
VSHDN = 0V
VSHDN = 5V
SHDN Voltage High
MIN
TYP
MAX
0.1
30
1
60
1.6
VSS = 0.1V
PWM Input High Voltage
5
10
PWM = 3.3V
SYNC Input High Voltage
V
15
μA
V
0.1
0.4
V
1
μA
1.5
V
SYNC Input Low Voltage
SYNC Pin Bias Current
0.4
1
PWM Input Low Voltage
PWM Pin Bias Current
SYNC = 0V
SYNC = 3.3V
VO_SW Switch Resistance
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3598E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
μA
μA
V
SHDN Voltage Low
Soft-Start Charging Current
UNITS
25
0.1
0.4
V
50
1
μA
μA
1000
Ω
characterization and correlation with statistical process controls. The
LT3598I is guaranteed over the full –40°C to 125°C operating junction
temperature range.
Note 3: Current flows out of FB pin.
Note 4: Current flows out of CTRL pin.
Note 5: Current limit guaranteed by design and/or correlation to static test.
Current limit is independent of duty cycle and is guaranteed by design.
3598fb
4
LT3598
TYPICAL PERFORMANCE CHARACTERISTICS
SHDN Pin Turn-On Threshold
SHDN Pin Current
1.5
Quiescent Current
50
6
125°C
1.4
1.3
–50°C
40
25°C
QUIESCENT CURRENT (mA)
SHDN PIN CURRENT (μA)
SHDN THRESHOLD (V)
45
35
30
25
20
15
10
5
4
3
5
1.2
–50
–25
0
25
50
75
100
0
125
0
5
10
TEMPERATURE (°C)
20
15
VSHDN (V)
25
2
–50
35
Reference Voltage
Oscillator Frequency
VIN = 5V
1.225
1.220
50
75
100
125
Switch Current Limit
2.8
2.5MHz
2.5
2.4
SWITCH CURRENT (A)
VIN = 30V
OSCILLATOR FREQUENCY (MHz)
VIN = 40V
25
3598 G03
3.0
1.230
0
3598 G02
1.240
1.235
–25
TEMPERATURE (°C)
3598 G01
REFERENCE VOLTAGE (V)
30
2.0
1.5
1MHz
1.0
0.5
2.0
1.6
1.2
0.8
200kHz
1.215
–50
–25
0
25
50
75
100
0
–50
125
–25
0
25
50
75
100
0.4
–50
125
–25
TEMPERATURE (°C)
TEMPERATURE (°C)
0
25
50
75
3598 G05
3598 G04
125
3598 G06
Soft-Start Pin Current
Switch VCESAT
0.40
100
TEMPERATURE (°C)
Feedback Pin Voltage
15.0
1.24
12.5
1.23
0.35
0.25
ISS (μA)
VCESAT (V)
FEEDBACK VOLTAGE (V)
25°C
0.30
125°C
0.20
–50°C
0.15
0.10
10.0
7.5
VC = 1.5V
1.22
VC = 1V
1.21
0.05
0
0
0.25
0.50
0.75
1.00
1.25
1.5O
SWITCH CURRENT (A)
5.0
–50
–25
0
25
50
75
100
125
–25
0
25
50
75
100
125
TEMPERATURE (°C)
TEMPERATURE (°C)
3598 G07
1.20
–50
3598 G08
3598 G09
3598fb
5
LT3598
TYPICAL PERFORMANCE CHARACTERISTICS
LED Current vs PWM Duty Cycle
LED Current vs Temperature
100
1
0.1
20
LED CURRENT (mA)
LED CURRENT (mA)
LED CURRENT (mA)
25
20.2
10
20.1
20.0
19.9
0.01
0.1
1
10
PWM DUTY CYCLE (%)
19.7
–50
100
–25
0
25
50
75
10
100
125
0
3.0
1.0
2.5
OPENLED CURRENT (mA)
1.5
0.0
–0.5
0
25
50
75
100
125
1.2
PWM
5V/DIV
SW
20V/DIV
2.0
1.5
IL
1A/DIV
ILED1
50mA/DIV
1.0
20μs/DIV
0
–50
–25
0
25
50
75
100
3598 G15
125
TEMPERATURE (°C)
TEMPERATURE (°C)
3598 G14
3598 G13
LED Current Waveforms
(0.1% PWM)
LED Current Waveforms
(90% PWM)
LED Current Waveforms
(90% PWM)
PWM
5V/DIV
PWM
5V/DIV
PWM
5V/DIV
SW
20V/DIV
SW
20V/DIV
SW
20V/DIV
IL
1A/DIV
ILED1
50mA/DIV
IL
1A/DIV
ILED1
50mA/DIV
IL
1A/DIV
ILED1
50mA/DIV
2μs/DIV
1.0
LED Current Waveforms
(0.1% PWM)
0.5
–1.0
0.4
0.8
0.6
CTRL VOLTAGE (V)
3598 G12
OPENLED Sink Current
0.5
0.2
3598 G11
LED Current Matching
vs Temperature
–25
0
TEMPERATURE (°C)
3598 G10
–1.5
–50
15
5
19.8
0.001
0.01
MATCHING (%)
LED Current vs CTRL Voltage
20.3
3598 G16
100μs/DIV
3598 G17
5μs/DIV
3598 G18
3598fb
6
LT3598
PIN FUNCTIONS
(QFN/ TSSOP)
LED1-6 (Pins 1, 2, 3, 4, 5, 6/Pins 4, 5, 6, 7, 8, 9): LED
String Output. Connect the bottom cathode of each LED string
to these pins. Tie pins to VOUT if the string is not used.
signal driving the PWM pin provides accurate dimming
control. The PWM signal can be driven from 0V to 5V. If
unused, the pin should be connected to VREF.
OPENLED (Pin 7/Pin 10): Open LED Flag When Any LED
String Opens. The output is open-collector. Tie a resistor
to other supply for open LED flag function.
RT (Pin 16/Pin 19): A resistor to ground programs
switching frequency between 200kHz and 2.5MHz. For
SYNC function, choose the resistor to program a frequency
20% slower than the SYNC pulse frequency. Do not leave
this pin open.
ISET (Pin 8/Pin 11): Programs LED Current for Each String.
Connect a 14.7k resistor between ISET and GND to program
each LED string current to 20mA. A 47pF capacitor on the
ISET pin reduces current ripple in each LED string.
CTRL (Pin 9/Pin 12): LED Current Control. If the CTRL
pin is not used, tie this pin to VREF through a 10k to 20k
resistor.
VC (Pin 10/Pin 13): Error Amplifier Output Pin. Tie the
external compensation network to this pin.
FB (Pin 11/Pin 14): Feedback Pin for Overvoltage
Protection. Reference voltage is 1.230V. Connect the
resistive divider tap here. Minimize trace area at FB. Set VOUT
according to VOUT = 1.230(1 + R2/R1) when overvoltage
protection occurs (see Figure 2).
TSET (Pin 12/Pin 15): An external resistor divider from
VREF programs a decrease in LED current versus internal
junction temperature (setting temperature breakpoint and
slope). If the TSET pin is not used, tie this pin to VREF.
NC (Pin 13/Pin 16): No Connection.
SYNC (Pin 14/Pin 17): Frequency Synchronization Pin.
This input allows for synchronizing the operating frequency
to an external clock. The RT resistor should be chosen to
program a switching frequency 20% slower than SYNC
pulse frequency. This pin should be grounded if this
feature is not used.
PWM (Pin 15/Pin 18): Input Pin for PWM Dimming Control.
Above 1V allows converter switching and below 0.4V
disables switching with VC pin level maintained. A PWM
SS (Pin 17/Pin 20): Soft-Start Pin. Place a soft-start
capacitor here. Upon start-up, a 10μA current charges
the capacitor. Use a larger capacitor for slower start-up.
Leave open if not used.
VREF (Pin 18/Pin 21): Bandgap Voltage Reference.
Internally set to 1.230V. This pin can supply up to 100μA.
Can be used to program the CTRL pin voltage using resistor
dividers to ground.
GND (Pin 19/Pin 22): Ground. Tie directly to local ground
plane.
SHDN (Pin 20/Pin 23): Shutdown Pin. Tie to 1.6V or more
to enable the device. Tie below 0.4V or less to disable
device. Do not float this pin.
VIN (Pin 21/Pin 24): Input Supply Pin. Must be locally
bypassed with a capacitor to ground.
SW (Pin 22/Pin 1): Switch Pin. This is the collector of the
internal NPN power switch. Minimize the metal trace area
connected to this pin to minimize EMI.
VOUT (Pin 23/ Pin 2): Output Pin. This pin provides power
to all LEDs.
VO_SW (Pin 24/ Pin 3): Drain of an Internal PMOS. The
internal PMOS disconnects the feedback resistors from
the VOUT pin during shutdown and the PWM transitioned
to low.
Exposed Pad (Pin 25/ Pin 25): Ground. The Exposed Pad
must be soldered to the PCB.
3598fb
7
LT3598
BLOCK DIAGRAM
SHDN
VIN
RT
SYNC
SW
OSCILLATOR
1.230VREF
SLOPE
3
VC
+
S
Q1
Q
–
A2
R
SS
+
GND
A3
GND
–
VOUT
PWM
PWM DIMMING
LOGIC
VO_SW
+
OVP gm
VREF
FB
–
+
0.8V
LED gm
–
CTRL
OPENLED
OPENLED DETECTION
TSET
VPTAT
–
+
VOUT
A1
LED1
LED2
LED
DRIVE
CIRCUITRY
LED3
LED
DISABLE
DETECTION LED4
LED5
ISET
LED6
3598 F01
Figure 1. Block Diagram
3598fb
8
LT3598
OPERATION
The LT3598 uses a constant-frequency, peak current mode
control scheme to provide excellent line and load regulation.
Each string can drive up to 30mA with 1.5% matching accuracy between strings. Operation can be best understood
by referring to the Block Diagram in Figure 1.
LT3598 has a built-in boost converter which converts the
input voltage to a higher output voltage to drive LEDs.
The LED strings are connected to current sources where
the current level is set with an external resistor on the
ISET pin. The LED1 to LED6 voltages are monitored for
output voltage regulation. During normal operation, when
all LEDs are used, the lowest LED pin voltage (LED1 to
LED6) is used to regulate the output voltage to ensure all
LED strings have enough voltage to run the programmed
current.
For any unused LED strings, tie their LED pins to VOUT.
An unused LED string is no longer in the regulation loop,
nor does it affect open LED detection. Never allow unused
LED strings to be left open.
The basic loop uses a pulse from an internal oscillator
to set the SR latch and turn on the internal power NPN
switch Q1. The signal at the noninverting input of the PWM
comparator (A2 slope) is proportional to the sum of the
switch current and oscillator ramp. When slope exceeds
VC (the output of the gm amplifier), the PWM comparator
resets the latch. The switch is then turned off, causing the
inductor current to lift the SW pin and turn on an external
Schottky diode connected to the output. Inductor current
flows via the Schottky diode charging the output capacitor. The switch is turned on again at the next reset cycle
of the internal oscillator. During normal operation, the VC
voltage controls the peak switch current limit and, hence,
the inductor current available to the output LEDs.
Dimming of the LEDs is accomplished by pulsing the LED
current using the PWM pin. When the PWM pin is low,
switching is disabled and the error amplifier is turned off
so that it does not drive the VC pin. Also, all internal loads
on the VC pin are disabled so that the state of the VC pin
is maintained on the external compensation capacitor.
This feature reduces transient recovery time. When the
PWM input again transitions high, the peak switch current
returns to the correct value.
The LT3598 uses the FB pin to provide overvoltage protection when all LED strings are open. There is an internal
PMOS switch between VOUT and VO_SW that is controlled
by the PWM signal. During the PWM off-period, this
PMOS is turned off, allowing for higher dimming range
and lower current during shutdown. A resistor divider is
connected between the VO_SW pin and ground, which sets
the overvoltage protection voltage.
If the LED1-6 pin voltage is below 0.2V (for a certain delay
after 80% of the programmed output voltage is reached),
the string is treated as an open LED string. As a result,
OPENLED flag is set. If a LED string is open in the middle
of the operation, the regulation will continue.
OPENLED detection is disabled during the start-up phase
to avoid erratic flag generation. An LED string that is
disabled by connecting its LED pin to VOUT is not an open
LED condition. During normal operation, if an LED string
is open and has the lowest LED pin voltage, the output
voltage will regulate itself to find another LED string that has
the lowest LED pin voltage at about 0.8V. If the open LED
string has an LED voltage above 0.8V, the output voltage
will remain the same. When the LED string is open, it is
no longer in the regulation loop. The OPENLED detection
is active only when the PWM signal is enabled. To avoid
spurious OPENLED detection and high PWM dimming
ratio, more output capacitance is recommended to allow
less voltage drop on VOUT.
During start-up, 10μA of current charges the external
soft-start capacitor. The SS pin directly limits the rate of
voltage rise on the VC pin, which in turn, limits the peak
switch current. Soft-start also enables the switching
frequency foldback to provide a clean start-up for the
LT3598. Current limit protects the power switch and
external components.
3598fb
9
LT3598
APPLICATIONS INFORMATION
Inductor Selection
Table 1 lists several inductors that work well with the
LT3598, however, there are many other manufacturers and
devices that can be used. Consult each manufacturer for
detailed information on their entire range of parts. Ferrite
core inductors should be used to obtain the best efficiency.
Choose an inductor that can handle the necessary peak
current without saturating. Also, ensure that the inductor
has a low DCR (copper wire resistance) to minimize I2R
power losses. Values between 4.7μH and 22μH will suffice
for most applications.
Inductor manufacturers specify the maximum current
rating as the current where inductance falls by a given
percentage of its nominal value. An inductor can pass a
current greater than its rated value without damaging it.
Consult each manufacturer to determine how the maximum
inductor current is measured and how much more current
the inductor can reliably conduct.
Table 1. Recommended Inductors
L
(μH)
MAX
DCR
(Ω)
CURRENT
RATING
(A)
B1015AS-100M
#817FY-4R7M
1123AS-4R7M
10
4.7
4.7
0.07
0.06
0.12
2.2
2.26
1.90
TOKO
www.toko.com
74454068
74454010
7447745100
6.8
10
10
0.055
0.065
0.12
2.2
2
1.7
Würth Electronics
www.we-online.com
CDH74NP-120L
CDH74NP-150L
CDRH6D38-100
12
15
10
0.065
0.083
0.038
2.45
2.10
2.00
Sumida
www.sumida.com
IHLP-2525BD-01
10
0.129
2.5
Vishay
www.vishay.com
SD25-4R7-R
4.7
0.056
1.83
Cooper
www.cooperet.com
PART
LPS4018-472ML
4.7
0.200
1.8
VENDOR
Coilcraft
www.coilcraft.com
Capacitor Selection
Low ESR (equivalent series resistance) ceramic capacitors
should be used at the output to minimize the output
ripple voltage. Use only X5R or X7R dielectrics, as these
materials retain their capacitance over wider voltage and
temperature ranges than other dielectrics. A 4.7μF to 10μF
output capacitor is sufficient for most high output current
designs. Table 2 lists some suggested manufacturers.
Consult the manufacturers for detailed information on
their entire selection of ceramic parts.
Table 2. Recommended Ceramic Capacitor Manufacturers
Taiyo Yuden
408-573-4150
www.t-yuden.com
AVX
843-448-9411
www.avxcorp.com
Murata
770-436-1300
www.murata.com
Kemet
408-986-0424
www.kemet.com
United Chemi-Con
847-696-2000
www.chemi-con.com
Diode Selection
Schottky diodes, with their low forward voltage drop
and fast switching speed, must be used for all LT3598
applications. Do not use P-N diodes. Table 3 lists several
Schottky diodes that work well. The diode’s average current
rating must exceed the application’s average output current.
The diode’s maximum reverse voltage must exceed the
application’s output voltage. A 2A diode is sufficient for
most designs. For PWM dimming applications, be aware
of the reverse leakage current of the diode. Lower leakage
current will drain the output capacitor less, allowing for
higher dimming range. The companies below offer Schottky
diodes with high voltage and current ratings.
Table 3. Suggested Diodes
PART
MAX
MAX REVERSE
CURRENT
VOLTAGE
(A)
(V)
MANUFACTURER
B250A
B240A
SBR140S3
SBM340, PDS340
2
2
1
3
50
40
40
40
Diodes, Inc.
www.diodes.com
HSM150G
HSM150J
1
1
50
50
Microsemi
www.microsemi.com
SS3H9
3
90
Vishay
www.vishay.com
3598fb
10
LT3598
APPLICATIONS INFORMATION
Overvoltage Protection
The LT3598 uses the FB pin to provide regulated overvoltage
protection when all LED strings are open. A resistor divider
is connected between the VO_SW pin and ground (Figure 2).
There is an internal PMOS switch between VOUT and
VO_SW, which is controlled by the PWM signal. The PMOS
switch addition prevents the feedback resistor divider from
draining the output capacitor during PWM off-period,
allowing for a higher dimming range without falsely tripping
the OPENLED flag. It also reduces the system current in
shutdown. This PMOS has about 1k resistance, so select
FB resistors taking this resistance into account.
To set the maximum output voltage, select the values
of R1 and R2 (see Figure 2) according to the following
equation:
⎛ R2 ⎞
VOUT(MAX ) = 1 . 230 V ⎜1+ ⎟
⎝ R1 ⎠
LT3598
The output voltage should be set 15% higher than the
normal LED string operating voltage. Under normal
operation, LED1 to LED6 pin voltages are monitored and
provide feedback information to the converter for output
voltage regulation given the programmed LED current.
The maximum output regulation loop is activated only
when all LEDs are open.
Programming Maximum LED Current
Maximum LED current is programmed by placing a resistor
between the ISET pin and ground (RISET). The ISET pin
resistor can be selected from 10k to 100k.
The LED current is programmed according to the following
equation:
ILED ≈
294V
RISET
See Table 4 and Figure 3 for resistor values and corresponding programmed LED current.
LED current can also be adjusted by programming the
CTRL pin voltage.
VOUT
VO_SW
Table 4. RISET Value Selection for LED Current
R2
FB
R1
3598 F02
Figure 2. Overvoltage Protection
Voltage Feedback Connections
RESISTOR ON ISET PIN (k)
3mA
97.6
10mA
29.4
20mA
14.7
30mA
9.76
LED Current Dimming
30
Two different types of dimming control can be used with
the LT3598. The LED current can be set by modulating
the CTRL pin or the PWM pin.
25
LED CURRENT (mA)
LED CURRENT (mA)
20
15
10
5
0
0
20
40
60
80
100
RISET (k)
3598 F03
For some applications, a variable DC voltage that adjusts
the LED current is the preferred method of brightness
control. The CTRL pin voltage can be modulated to set
the dimming of the LED string (see Figures 4 and 5). As
the voltage on the CTRL pin increases from 0V to 1.0V,
the LED current increases from 0 to the programmed LED
current level. As the CTRL pin voltage increases beyond
1V, it has no effect on the LED current.
Figure 3. RISET Value Selection for LED Current
3598fb
11
LT3598
APPLICATIONS INFORMATION
35
For wide PWM dimming range, higher switching frequency and lower PWM frequency configuration are
needed. Special considerations are required for component
selection and compensation network. Please contact
factory for optimized components selection if very high
dimming ratio is desired.
RISET = 9.76k
LED CURRENT (mA)
30
25
20
15
LED Current Derating Using the CTRL Pin
10
5
A useful feature of the LT3598 is its ability to program
a derating curve for maximum LED current versus
temperature. LED data sheets provide curves of maximumallowable LED current versus temperature to warn against
exceeding this current limit and damaging the LED. The
LT3598 allows the output LEDs to be programmed for
maximum allowable current while still protecting the
LEDs from excessive currents at high temperature. This
is achieved by programming a voltage at the CTRL pin
with a negative temperature coefficient using a resistor
divider with temperature dependent resistance (Figure 7).
As ambient temperature increases, the CTRL voltage will
fall below the internal 1V voltage reference, causing LED
currents to be controlled by the CTRL pin voltage. The LED
current curve breakpoint and slope versus temperature
is defined by the choice of resistor ratios and use of
temperature-dependent resistance in the divider for the
CTRL pin.
0
0
0.2
0.4
0.6
0.8
1
1.2
1.4
CTRL (V)
1.6
3598 F04
Figure 4. LED Current vs CTRL Voltage
VREF
R2
LT3598
CTRL
R1
3598 F05
Figure 5. LED Current vs CTRL
TPWM
TONPWM
(= 1/fPWM)
PWM
INDUCTOR
CURRENT
LED
CURRENT
MAX ILED
3598 F06
Figure 6. LED Current Using PWM Dimming
For True Color PWMTM dimming, the LT3598 provides up
to a 3000:1 PWM dimming range. This is achieved by
allowing the duty cycle of the PWM pin (connected to
the IC and an internal switch in series with the LED(s)),
to be reduced from 100% to as low as 0.1% for a PWM
frequency of 100Hz (Figure 6). PWM duty cycle dimming
allows for constant LED color to be maintained over the
entire dimming range.
Table 5 shows a list of manufacturers/distributors of
NTC resistors. There are several other manufacturers
available and the chosen supplier should be contacted
for more detailed information. If an NTC resistor is used
to indicate LED temperature, it is effective only if the
resistor is connected as closely as possible to the LED
strings. LED derating curves shown by manufacturers are
listed for ambient temperature. The NTC resistor should
have the same ambient temperature as the LEDs. Since
the temperature dependency of an NTC resistor can be
nonlinear over a wide range of temperatures, it is important
to obtain a resistor’s exact value over temperature from
the manufacturer. Hand calculations of CTRL voltage can
then be performed at each given temperature, resulting
in the CTRL versus temperature plotted curve. Several
iterations of resistor value calculations may be required
to achieve the desired breakpoint and slope of the LED
current derating curve.
3598fb
12
LT3598
APPLICATIONS INFORMATION
Table 5. NTC Resistor Manufacturers/Distributors
Murata Electronics North America
770-436-1300
www.murata.com
TDK Corporation
516-535-2600
www.tdk.com
Digi-Key
800-344-4539
www.digikey.com
If calculating the CTRL voltage at various temperatures
gives a downward slope that is too strong, alternative
resistor networks can be chosen (B, C, D in Figure 7)
which use temperature independent resistance to reduce
the effects of the NTC resistor overtemperature.
Murata Electronics provides a selection of NTC resistors
with complete data over a wide range of temperatures.
In addition, a software tool is available which allows the
user to select from different resistor networks and NTC
resistor values, and then simulate the exact output voltage
curve (CTRL behavior) overtemperature. Referred to as the
“Murata Chip NTC Thermistor Output Voltage Simulator,”
users can log onto www.murata.com and download
the software followed by instructions for creating an
output voltage VOUT (CTRL) from a specified VCC supply
(VREF).
Using the TSET Pin for Thermal Protection
The LT3598 contains a special programmable thermal
regulation loop that limits the internal junction temperature
of the part. Since the LT3598 topology consists of a single
boost converter with six linear current sources, any LED
string voltage mismatch will cause additional power to
be dissipated in the package. This topology provides
excellent current matching between LED strings and allows
a single power stage to drive a large number of LEDs, but
at the price of additional power dissipation inside the part
(which means a higher junction temperature). Being able
to limit the maximum junction temperature allows the
benefits of this topology to be fully realized. This thermal
regulation feature provides important protection at high
ambient temperatures, and allows a given application
to be optimized for typical, not worst-case, ambient
temperatures with the assurance that the LT3598 will
automatically protect itself and the LED strings under
worst-case conditions.
The operation of the thermal loop is simple. As the ambient
temperature increases, so does the internal junction
temperature of the part. An internal voltage is developed
that’s proportional to the junction temperature (VPTAT).
Once the programmed maximum junction temperature
is reached, the LT3598 begins to linearly reduce the LED
current, as needed, to try and maintain this temperature.
This can only be achieved when the ambient temperature
stays below the desired maximum junction temperature.
If the ambient temperature continues to rise past the
programmed maximum junction temperature, the LEDs
current will be reduced to approximately 5% of the full
LED current.
While this feature is intended to directly protect the LT3598,
it can also be used to derate the LED current at high
temperatures. Since there is a direct relationship between
the LED temperature and LT3598 junction temperature, the
TSET function also provides some LED current derating
at high temperatures.
Two external resistors program the maximum IC junction
temperature using a resistor divider from the VREF pin,
as shown in Figure 8. Choose the ratio of R1 and R2 for
the desired junction temperature. Figure 9 shows the
relationship of TSET voltage to junction temperature, and
Table 6 shows commonly used values for R1 and R2.
RY
VREF
R2
RY
LT3598
CTRL
RNTC
RNTC
RX RNTC
RNTC
RX
R1
(OPTION A TO D)
A
B
C
D
3598 F07
Figure 7 . LED Current Derating vs Temperature Using NTC Resistor
3598fb
13
LT3598
APPLICATIONS INFORMATION
Programming Switching Frequency
Table 6. TSET Junction Temperature
TJ (°C)
R1
R2
90
100k
68.1k
100
100k
63.4k
110
100k
59k
120
100k
54.9k
Selecting the optimum switching frequency depends
on several factors. Inductor size is reduced with higher
frequency, but efficiency drops slightly due to higher
switching losses. In addition, some applications require
very high duty cycles to drive a large number of LEDs from
a low supply. Low switching frequency allows a greater
operational duty cycle and, hence, a greater number of
LEDs to be driven. In each case, the switching frequency
can be tailored to provide the optimum solution. When
programming the switching frequency, the total power
losses within the IC should be considered.
VREF
R2
The switching frequency of the LT3598 should be
programmed between 200kHz and 2.5MHz by an external
resistor connected between the RT pin and ground. Do not
leave this pin open. See Table 7 and Figure 10 for resistor
values and corresponding frequencies.
LT3598
TSET
R1
3598 F08
Figure 8. Programming the TSET Pin
900
VTSET THRESHOLD (mV)
850
Table 7. Switching Frequency
800
750
700
650
600
550
500
0
25
50
75
100
125
JUNCTION TEMPERATURE (°C)
150
3598 F09
Figure 9. TSET Pin Threshold
SWITCHING FREQUENCY (MHz)
2.5
2.0
1.5
1.0
0.5
0
10
100
RT (k)
1000
3598 F10
SWITCHING FREQUENCY (MHz)
RT (k)
2.5
14.7
2
20.5
1.5
29.4
1
51.1
0.5
105
0.2
301
Switching Frequency Synchronization
The nominal operating frequency of the LT3598 is
programmed using a resistor from the RT pin to ground
and can be controlled over a 200kHz to 2.5MHz range. In
addition, the internal oscillator can be synchronized to an
external clock applied to the SYNC pin. The synchronizing
clock signal input to the LT3598 must have a frequency
between 250kHz and 3MHz, a duty cycle between 20% and
80%, a low state below 0.4V and a high state above 1.5V.
Synchronization signals outside of these parameters will
cause erratic switching behavior. For proper operation,
an RT resistor should be chosen to program a switching
frequency 20% slower than the SYNC pulse frequency.
Synchronization occurs at a fixed delay after the rising
edge of SYNC.
Figure 10. Switching Frequency
3598fb
14
LT3598
APPLICATIONS INFORMATION
The SYNC pin should be grounded if the clock synchronization feature is not used. When the SYNC pin is
grounded, the internal oscillator generates switching
frequency to the converter.
Loop Compensation
For many applications, it is necessary to minimize the
inrush current at start-up. The LT3598’s soft-start circuit
significantly reduces the start-up current spike and output
voltage overshoot. Before the SS pin voltage reaches 1V,
the switching frequency will also fold back proportional
to the SS pin voltage. A typical value for the soft-start
capacitor is 10nF.
The LT3598 has an internal transconductance error
amplifier for LED current regulation whose VC output
compensates the control loop. During an open LED
event where all LED strings are open, the VC node also
compensates the control loop. The external inductor,
output capacitor, and the compensation resistor and
capacitor determine the loop stability. The inductor and
output capacitor are chosen based on performance, size
and cost. The compensation resistor and capacitor at VC
are selected to optimize control loop stability. For typical
LED applications, a 15nF compensation capacitor in series
with a 3k resistor at VC is adequate.
OPENLED FLAG
Thermal Considerations
The OPENLED pin is an open-collector output and needs
an external resistor tied to a supply (see Figure 11). If any
LED string is open during normal operation, the OPENLED
pin will be pulled down.
The LT3598 provides six channels for LED strings with
internal NPN devices serving as constant-current sources.
When LED strings are regulated, the lowest LED pin voltage
is typically 0.8V. The higher the programmed LED current,
the more power dissipation in the LT3598. For 30mA LED
programming current with a 100% PWM dimming ratio,
at least 144mW is dissipated within the IC due to current
sources. If the forward voltages of the six LED strings are
very dissimilar, there can be significant power dissipation.
Thermal calculations shall include the power dissipation
on current sources in addition to conventional switch DC
loss, switch AC loss and input quiescent loss. For best
efficiency, it is recommended that all channels have the
same number of LEDs, and each string has a similar voltage
drop across the LEDs.
Soft-Start and Switching Frequency Foldback
LT3598
R1
OPENLED
3598 F11
Figure 11. OPENLED Connection
The OPENLED flag is only activated after the first PWM
edge. The open LED detection is enabled only when the
PWM signal is enabled. There is a delay for OPENLED
flag generation when the PWM signal is enabled to avoid
generating a spurious flag signal. The maximum current
the OPENLED can sink is typically 2mA.
During start-up (see the Operation section), the open LED
detection is disabled. If an LED string is not used and tied
to VOUT, the string will not be in any fault detection.
Board Layout Considerations
As with all switching regulators, careful attention must be
paid to the PCB board layout and component placement.
To prevent electromagnetic interference (EMI) problems,
proper layout of high frequency switching paths is essential.
Minimize the length and area of all traces connected to the
switching node pin (SW). Always use a ground plane under
the switching regulator to minimize interplane coupling.
Good grounding is essential in LED fault detection.
3598fb
15
LT3598
TYPICAL APPLICATIONS
LED Driver for 40 White LEDs with Two Channels Unused
L1
10μH
PVIN
6V TO 40V
C1
2.2μF
VIN
5V
C3
2.2μF
R6
100k
D1
VIN
SW
C2
4.7μF
VOUT
VO_SW
R4
1.00M
OPENLED
SHDN
SHDN
PWM
PWM
SYNC
SYNC
FB
R5
30.9k
LT3598
RT
R1
51.1k
VREF
RHOT
10k
LED1
LED2
LED3
LED4
LED5
LED6
GND VC
CTRL
RNTC
100k
R8
60.4k
TSET ISET
R7
100k
C5
47pF
SS
R3
14.7k
C4
0.1μF
20mA
3598 TA02a
RC
2.61k
CC
15nF
C1: TAIYO YUDEN GMK325BJ225ML
C2: MURATA GRM32ER71H475K
C3: TAIYO YUDEN LMK212BJ225MG
D1: DIODES, INC. B240A
L1: WÜRTH ELEKTRONIK 744777410
RNTC : MURATA NCP18WF104J03RB
Efficiency (PWM Dimming)
95
PVIN = 25V
90
EFFICIENCY (%)
85
PVIN = 12V
80
75
70
65
60
55
50
0
10
20
30 40 50 60 70
TOTAL LED CURRENT (mA)
80
90
3598 TA02b
3598fb
16
LT3598
TYPICAL APPLICATIONS
LED Driver for 30 White LEDs with 60mA Each String
L1
10μH
PVIN
6V TO 40V
C1
2.2μF
VIN
5V
C3
2.2μF
R6
100k
SHDN
CTRL
PWM
SYNC
VIN
D1
SW
C2
4.7μF
VOUT
VO_SW
OPENLED
SHDN
CTRL
PWM
SYNC
RT
R4
1.00M
FB
R5
30.9k
LT3598
R1
51.1k
VREF
RHOT
10k
CTRL
RNTC
100k
R8
60.4k
TSET ISET
R7
100k
C5
47pF
SS
LED1
LED2
LED3
LED4
LED5
LED6
GND VC
C4
0.1μF
R3
9.76k
60mA
RC
2.61k
CC
15nF
3598 TA03a
C1: TAIYO YUDEN GMK325BJ225ML
C2: MURATA GRM32ER71H475KA88L
C3: TAIYO YUDEN LMK212BJ225MG
D1: VISHAY SS3H9
L1: WÜRTH ELEKTRONIK 744777410
RNTC : MURATA NCP18WF104J03RB
Efficiency (PWM Dimming)
Dimming Range (1000:1 PWM) at 125°C
Junction Temperature, 10ms Period
EFFICIENCY (%)
100
95
PVIN = 25V
90
PVIN = 12V
PWM
5V/DIV
85
SW
20V/DIV
80
75
ILED1
100mA/DIV
70
2μs/DIV
65
3598
60
0
20
40
60 80 100 120 140 160 180
TOTAL LED CURRENT (mA)
3598 TA03b
3598fb
17
LT3598
TYPICAL APPLICATIONS
Auto Battery Powered Driver for 20 LEDs with 90mA Each String
L1
4.7μH
PVIN
6V TO 40V
C1
2.2μF
VIN
5V
C3
2.2μF
VIN
D1
SW
C2
4.7μF
VOUT
VO_SW
100k
R4
1.00M
OPENLED
SHDN
CTRL
PWM
SHDN
CTRL
PWM
SYNC
RT
FB
R5
30.9k
LT3598
R1
51.1k
VREF
R10
20k
CTRL
R8
60.4k
TSET ISET
R7
100k
C5
56pF
SS
LED1
LED2
LED3
LED4
LED5
LED6
GND VC
C4
0.1μF
R3
9.76k
90mA
RC
5.11k
CC
6.8nF
3598 TA04a
C1: NIPPON CHEMI-CON KTS500B225M32NOTOO
C2: MURATA GRM32ER71H475KA88L
C3: TAIYO YUDEN LMK212BJ225MG
D1: VISHAY SS3H9
L1: WÜRTH ELEKTRONIK 7447785004
Dimming Range 1000:1 PWM,
10ms Period (125°C Junction Temperature)
Efficiency
95
EFFICIENCY (%)
90
PWM
5V/DIV
85
80
ILED1
100mA/DIV
75
70
65
5μs/DIV
3598 TA04c
60
0
20
40
60 80 100 120 140 160 180
TOTAL LED CURRENT (mA)
3598 TA04b
3598fb
18
LT3598
TYPICAL APPLICATIONS
2 MHz LED Driver for 20 White LEDs
PVIN
11.4V TO 12.6V
C1
2.2μF
L1
10μH
VIN
3.2V TO 5.5V
C3
2.2μF
R6
100k
VIN
D1
SW
C2
4.7μF
VOUT
VO_SW
R4
2.4M
OPENLED
SHDN
SHDN
PWM
PWM
SYNC
SYNC
FB
R5
140k
LT3598
RT
R1
21.5k
VREF
R9
10k
CTRL
R8
107k
TSET ISET
C5
47pF
R7
178k
SS
LED1
LED2
LED3
LED4
LED5
LED6
VC
GND
R3
14.7k
C4
0.1μF
20mA
3598 TA02a
RC
2k
CC
10nF
C6
100pF
C1: MURATA GRM21BR71E225K
C2: MURATA GRM32ER71H475K
C3: TAIYO YUDEN LMK212BJ225MG
D1: DIODES, INC. SBR140S3
L1: TOKO 1123AS-100M
PWM Dimming (3000:1)
PWM
5V/DIV
IL
200mA/DIV
ILED, total
50mA/DIV
PVIN = 12V, VIN = 3.3V
1μs/DIV
3598 TA07a
3598fb
19
LT3598
TYPICAL APPLICATIONS
1 MHz LED Driver for 36 White LEDs
L1
10μH
VIN
5V
C1
2.2μF
R6
100k
C3
1μF
VIN
D1
SW
C2
4.7μF s 2
VOUT
VO_SW
R4
2.4M
OPENLED
SHDN
SHDN
PWM
PWM
SYNC
SYNC
FB
R5
76.8k
LT3598
RT
R1
53.6k
VREF
R9
10k
LED1
LED2
LED3
LED4
LED5
LED6
GND VC
CTRL
R8
107k
TSET ISET
C5
47pF
SS
R3
11.5k
C4
0.1μF
25mA
3598 TA07
RC
3k
CC
10nF
C6
100pF
C1: MURATA GRM21BR71A225K
C2: MURATA GRM32ER71H475K
D1: DIODES, INC. SBR140S3
L1: VISHAY IHLP-2525BD-01
PWM Dimming (20μS Pulse Width)
PWM
5V/DIV
IL
500mA/DIV
ILED, total
50mA/DIV
PVIN = VIN = 5V
3598 TA06
5μs/DIV
3598fb
20
LT3598
PACKAGE DESCRIPTION
FE Package
24-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1771 Rev Ø)
Exposed Pad Variation AA
7.70 – 7.90*
(.303 – .311)
3.25
(.128)
3.25
(.128)
24 23 22 21 20 19 18 17 16 15 14 13
6.60 p0.10
2.74
(.108)
4.50 p0.10
6.40
2.74 (.252)
(.108) BSC
SEE NOTE 4
0.45 p0.05
1.05 p0.10
0.65 BSC
1 2 3 4 5 6 7 8 9 10 11 12
RECOMMENDED SOLDER PAD LAYOUT
4.30 – 4.50*
(.169 – .177)
0.09 – 0.20
(.0035 – .0079)
0.25
REF
0.50 – 0.75
(.020 – .030)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
3. DRAWING NOT TO SCALE
1.20
(.047)
MAX
0o – 8o
0.65
(.0256)
BSC
0.195 – 0.30
(.0077 – .0118)
TYP
0.05 – 0.15
(.002 – .006)
FE24 (AA) TSSOP 0208 REV Ø
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
3598fb
21
LT3598
PACKAGE DESCRIPTION
UF Package
24-Lead Plastic QFN (4mm × 4mm)
(Reference LTC DWG # 05-08-1697)
0.70 ±0.05
4.50 ± 0.05
2.45 ± 0.05
3.10 ± 0.05 (4 SIDES)
PACKAGE OUTLINE
0.25 ±0.05
0.50 BSC
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
4.00 ± 0.10
(4 SIDES)
BOTTOM VIEW—EXPOSED PAD
R = 0.115
TYP
0.75 ± 0.05
PIN 1 NOTCH
R = 0.20 TYP OR
0.35 × 45° CHAMFER
23 24
PIN 1
TOP MARK
(NOTE 6)
0.40 ± 0.10
1
2
2.45 ± 0.10
(4-SIDES)
(UF24) QFN 0105
0.200 REF
0.00 – 0.05
0.25 ± 0.05
0.50 BSC
NOTE:
1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)—TO BE APPROVED
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE, IF PRESENT
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
3598fb
22
LT3598
REVISION HISTORY
(Revision history begins at Rev B)
REV
DATE
DESCRIPTION
PAGE NUMBER
B
7/10
Updated data sheet title and 3rd bullet under Features to ±1.5%
1
Changed VIN condition in Reference Voltage Line Regulation to 3.2V
3
Deleted VIN = 5V conditions from SHDN Pin Current
4
Revised voltage in PWM description in Pin Functions
7
Fixed minor typo
9
Added “15%” to first sentence of third paragraph
11
Added information to Using TSET Pin for Thermal Protection section
13
Changed to 250kHz in Switching Frequency Synchronization section
14
3598fb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
23
LT3598
TYPICAL APPLICATION
Efficiency vs Total LED Current
90% Efficient LED Driver for 60 White LEDs
PVIN
8V TO 40V
100
VIN
SW
C2
4.7μF
VOUT
SHDN
PWM
PWM
SYNC
SYNC
90
R4
1.00M
OPENLED
SHDN
FB
R5
30.9k
LT3598
RT
95
VIN = 25V
VO_SW
100k
EFFICIENCY (%)
C1
2.2μF
D1
L1, 10μH
VIN
5V
C3
2.2μF
R1
51.1k
VIN = 16V
85
80
75
70
65
VREF
RHOT
10k
CTRL
RNTC
100k
R8
60.4k
TSET ISET
R7
100k
C5
47pF
R3
14.7k
SS
60
LED1
LED2
LED3
LED4
LED5
LED6
GND VC
C4
10nF
0
20
40
60
80
100
TOTAL LED CURRENT (mA)
3598 TA05b
20mA
RC
2.61k
CC
15nF
120
3598 TA04a
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT3474/
LT3474-1
36V, 1A (ILED), 2MHz, Step-Down LED Driver
VIN: 4V to 36V, VOUT(MAX) = 13.5V, True Color PWM Dimming = 400:1,
ISD < 1μA, TSSOP-16E Package
LT3475/
LT3475-1
Dual 1.5A (ILED), 36V, 2MHz, Step-Down LED Driver
VIN: 4V to 36V, VOUT(MAX) = 13.5V, True Color PWM Dimming = 3000:1,
ISD < 1μA, TSSOP-20E Package
LT3476
Quad Output 1.5A, 2MHz High Current LED Driver with
1000:1 Dimming
VIN: 2.8V to 16V, VOUT(MAX) = 36V, True Color PWM Dimming = 1000:1,
ISD < 10μA, 5mm × 7mm QFN-10 Package
LT3477
3A, 42V, 3MHz Boost, Buck-Boost, Buck LED Driver
VIN: 2.5V to 25V, VOUT(MAX) = 40V, Dimming = Analog/PWM, ISD < 1μA,
QFN and TSSOP20E Packages
LT3478/LT3478-1 4.5A, 42V, 2.5MHz High Current LED Driver with 3000:1 VIN: 2.8V to 36V, VOUT(MAX) = 42V, True Color PWM Dimming = 3000:1,
Dimming
ISD < 3μA, TSSOP16E Package
LT3486
Dual 1.3A, 2MHz High Current LED Driver
VIN: 2.5V to 24V, VOUT(MAX) = 36V, True Color PWM Dimming = 1000:1,
ISD < 1μA, 5mm × 3mm DFN and TSSOP-16E Packages
LT3496
45V, 2.1MHz 3-Channel (ILED = 1A) Full Featured
LED Driver
VIN: 3V to 30V (40VMAX), VOUT(MAX) = 45V, True Color PWM Dimming =
3000:1, ISD < 1μA, 4mm × 3mm QFN-28 Package
LT3497
Dual 2.3MHz, Full Function LED Driver with Integrated
Schottkys and 250:1 True Color PWM Dimming
VIN: 2.5V to 10V, VOUT(MAX) = 32V, IQ = 6mA, ISD < 12μA, 2mm × 3mm
DFN-10 Package
LT3498
2.3MHz, 20mA LED Driver and OLED Driver with
Integrated Schottky
VIN: 2.5V to 12V, VOUT(MAX) = 32V, IQ = 1.65mA, ISD < 9μA, 2mm × 3mm
DFN-10 Package
LT3518/LT3517
2.3A/1.3A 45V, 2.5MHz Full Featured LED Driver with
True Color PWM Dimming
VIN: 3V to 30V (40VMAX), VOUT(MAX) = 42V, True Color PWM Dimming =
3000:1, ISD < 5μA, 4mm × 4mm QFN-16 Package
LT3590
48V, 850kHz 50mA Buck Mode LED Driver
VIN: 4.5V to 55V, Dimming = 200:1 True Color PWM, ISD < 15μA,
2mm × 2mm DFN-6 and SC70 Packages
LT3592
36V, 2.2MHz, 500mA Buck Mode LED Driver
VIN: 3.6V to 36V, True Color PWM Dimming = 10:1, ISD < 1μA, 2mm × 3mm
DFN-10 and MSOP-10E Packages
LT3595
45V, 2.5MHz 16-Channel Full Featured LED Driver
VIN: 4.5V to 55V, VOUT(MAX) = 45V, True Color PWM Dimming = 5000:1,
ISD < 1μA, 5mm × 9mm QFN-56 Package
3598fb
24 Linear Technology Corporation
LT 0710 REV B • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2008