LT3685 36V, 2A, 2.4MHz Step-Down Switching Regulator FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ DESCRIPTION The LT®3685 is an adjustable frequency (200kHz to 2.4MHz) monolithic step-down switching regulator that accepts input voltages up to 38V operating and 60V maximum. An internal overvoltage protection circuit turns off the power switch when VIN is above 38V typical (36V minimum) which then allows the part to safely withstand 60V transients. A high efficiency 0.25 switch is included on the die along with a boost Schottky diode and the necessary oscillator, control, and logic circuitry. Current mode topology is used for fast transient response and good loop stability. The LT3685’s high operating frequency allows the use of small, low cost inductors and ceramic capacitors resulting in low output ripple while keeping total solution size to a minimum. The low current shutdown mode reduces input supply current to less than 1μA while a resistor and capacitor on the RUN/SS pin provide a controlled output voltage ramp (soft-start). A power good flag signals when VOUT reaches 89% of the programmed output voltage. The LT3685 is available in 10-Pin MSOP and 3mm × 3mm DFN packages with exposed pads for low thermal resistance. Wide Input Range: Operation From 3.6V to 36V Overvoltage Lockout Protects Circuit through 60V Transients 2A Maximum Output Current Adjustable Switching Frequency: 200kHz to 2.4MHz Low Shutdown Current: IQ < 1μA Integrated Boost Diode Synchronizable Between 250kHz to 2MHz Power Good Flag Saturating Switch Design: 0.25 On-Resistance 0.790V Feedback Reference Voltage Output Voltage: 0.79V to 20V Soft-Start Capability Small 10-Pin Thermally Enhanced MSOP and (3mm × 3mm) DFN Packages APPLICATIONS ■ ■ ■ ■ ■ Automotive Battery Regulation Set Top Box Distributed Supply Regulation Industrial Supplies Wall Transformer Regulation , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. Burst Mode is a registered trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION 3.3V Step-Down Converter VIN OFF ON BD RUN/SS BOOST 0.47μF 4.7μH VC LT3685 SW RT 470pF PG 40.2k SYNC VOUT = 5V 90 14k 4.7μF 100 VOUT 3.3V 2A EFFICIENCY (%) VIN 4.5V TO 36V TRANSIENT TO 60V Efficiency 70 60 316k GND VOUT = 3.3V 80 VIN = 12V L = 5.6μH F = 800 kHz FB 22μF 100k 50 0 3685 TA01 0.5 1.0 1.5 LOAD CURRENT (A) 2 3685 TA01b 3685fb 1 LT3685 ABSOLUTE MAXIMUM RATINGS (Note 1) VIN, RUN/SS Voltage (Note 5) ...................................60V BOOST Pin Voltage ...................................................56V BOOST Pin Above SW Pin.........................................30V FB, RT, VC Voltage .......................................................5V PG, BD, SYNC Voltage ..............................................30V Operating Junction Temperature Range (Note 2) LT3685E ............................................. –40°C to 125°C LT3685I .............................................. –40°C to 125°C Storage Temperature Range................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) (MSE Only) ....................................................... 300°C PIN CONFIGURATION TOP VIEW TOP VIEW BD 1 10 RT BOOST 2 9 VC SW 3 VIN 4 7 PG RUN/SS 5 6 SYNC 11 BD BOOST SW VIN RUN/SS 8 FB 1 2 3 4 5 10 9 8 7 6 11 RT VC FB PG SYNC MSE PACKAGE 10-LEAD PLASTIC MSOP DD PACKAGE 10-LEAD (3mm s 3mm) PLASTIC DFN JA = 45°C/W, JC = 10°C/W EXPOSED PAD (PIN 11) IS GND, MUST BE SOLDERED TO PCB JA = 45°C/W, JC = 10°C/W EXPOSED PAD (PIN 11) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LT3685EDD#PBF LT3685IDD#PBF LT3685EMSE#PBF LT3685IMSE#PBF LT3685EDD#TRPBF LT3685IDD#TRPBF LT3685EMSE#TRPBF LT3685IMSE#TRPBF LCYG LCYG LTCYF LTCYF 10-Lead (3mm × 3mm) Plastic DFN 10-Lead (3mm × 3mm) Plastic DFN 10-Lead Plastic MSOP 10-Lead Plastic MSOP –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC Marketing for information on non-standard lead based finish parts. *For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 10V, VRUN/SS = 10V, VBOOST = 15V, VBD = 3.3V unless otherwise noted. (Note 2) PARAMETER CONDITIONS MIN Minimum Input Voltage ● VIN Overvoltage Lockout ● Quiescent Current from VIN VRUN/SS = 0.2V VBD = 3V, Not Switching VBD = 0, Not Switching ● 36 TYP MAX 3 3.6 UNITS V 38 40 V 0.01 450 1.3 0.5 600 1.7 μA μA mA 3685fb 2 LT3685 ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 10V, VRUN/SS = 10V VBOOST = 15V, VBD = 3.3V unless otherwise noted. (Note 2) PARAMETER CONDITIONS Quiescent Current from BD VRUN/SS = 0.2V VBD = 3V, Not Switching VBD = 0, Not Switching MIN ● Minimum Bias Voltage (BD Pin) Feedback Voltage ● FB Pin Bias Current (Note 3) VC = 1.2V FB Voltage Line Regulation 4V < VIN < 36V 780 775 ● TYP MAX 0.01 0.9 1 0.5 1.3 5 2.7 3 790 790 800 805 mV mV 7 30 nA 0.002 0.01 Error Amp gm 500 Error Amp Gain 1000 UNITS μA mA μA V %/V μMho VC Source Current 45 μA VC Sink Current 45 μA VC Pin to Switch Current Gain 3.5 A/V VC Clamp Voltage Switching Frequency 2 RT = 8.66k RT = 29.4k RT = 187k 2.1 0.9 160 2.4 1 200 2.7 1.15 240 MHz MHz kHz 60 150 nS 3.2 3.7 4.2 A ● Minimum Switch Off-Time Switch Current Limit Duty Cycle = 5% Switch VCESAT ISW = 2A Boost Schottky Reverse Leakage VSW = 10V, VBD = 0V 500 ● Minimum Boost Voltage (Note 4) V mV 0.02 2 μA 1.5 2.1 V BOOST Pin Current ISW = 1A 22 35 mA RUN/SS Pin Current VRUN/SS = 2.5V 5 10 μA 2.5 V RUN/SS Input Voltage High RUN/SS Input Voltage Low PG Threshold Offset from Feedback Voltage 0.2 V VFB Rising 90 PG Leakage VPG = 5V 0.1 PG Sink Current VPG = 0.4V PG Hysteresis 12 SYNC Low Threshold ● 100 mV 1 600 V 0.7 VSYNC = 0V Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT3685E is guaranteed to meet performance specifications from 0°C to 125°C. Specifications over the –40°C to 125°C operating temperature range are assured by design, characterization and correlation with statistical process controls. The LT3685I specifications are guaranteed over the –40°C to 125°C temperature range. μA μA 0.5 SYNC High Threshold SYNC Pin Bias Current mV 0.1 V μA Note 3: Bias current flows out of the FB pin. Note 4: This is the minimum voltage across the boost capacitor needed to guarantee full saturation of the switch. Note 5: Absolute Maximum Voltage at VIN and RUN/SS pins is 60V for nonrepetitive 1 second transients, and 40V for continuous operation. 3685fb 3 LT3685 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency Efficiency 100 Maximum Load Current 90 4.0 VIN = 7V 85 VIN = 12V 90 TA = 25°C unless otherwise noted. VIN = 12V 3.5 TYPICAL VIN = 24V 70 LOAD CURRENT (A) VIN = 34V 80 EFFICIENCY (%) EFFICIENCY (%) 80 VIN = 34V 75 VIN = 24V 70 65 2.5 MINIMUM 2.0 60 60 0 VOUT = 3.3V 50 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 LOAD CURRENT (A) 0 L: NEC PLC-0745-5R6 f: 800kHz 1.0 5 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 LOAD CURRENT (A) 3685 G01 4.5 TYPICAL 4.0 MINIMUM 2.0 1.5 VOUT = 5V L = 4.7μH f = 800kHz 1.0 20 15 INPUT VOLTAGE (V) 25 30 3.5 SWITCH CURRENT LIMIT (A) SWITCH CURRENT LIMIT(A) 2.5 3.0 2.5 2.0 1.5 DUTY CYCLE = 10 % 3.5 3.0 DUTY CYCLE = 90 % 2.5 2.0 1.5 1.0 0.5 1.0 20 0 80 60 40 DUTY CYCLE (%) 100 0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3685 G06 3685 G05 3685 G04 Boost Pin Current Switch Voltage Drop 700 80 600 70 BOOST PIN CURRENT (mA) VOLTAGE DROP (mV) 30 Switch Current Limit 4.0 3.0 25 3685 G03 Switch Current Limit Maximum Load Current 10 15 20 INPUT VOLTAGE (V) 10 3685 G02 3.5 5 VOUT = 3.3V L = 4.7μH f = 800 kHz 1.5 55 L: NEC PLC-0745-5R6 f: 800kHz VOUT = 5V 50 LOAD CURRENT (A) 3.0 500 400 300 200 100 60 50 40 30 20 10 0 0 0 500 1000 2000 1500 SWITCH CURRENT (mA) 2500 3685 G07 0 500 1000 1500 2000 SWITCH CURRENT (mA) 2500 3685 G08 3685fb 4 LT3685 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25°C unless otherwise noted. Switching Frequency Feedback Voltage 840 1.20 Frequency Foldback 1200 RT = 29.4k SWITCHING FREQUENCY (kHz) 820 1.10 FREQUENCY (MHz) FEEDBACK VOLTAGE (mV) 1.15 800 1.05 1.00 0.95 0.90 780 1000 0.85 760 –50 –25 0 0 200 0 3.5 80 60 40 20 RUN/SS Pin Current 12 RUN/SS PIN CURRENT (μA) 120 SWITCH CURRENT LIMIT (A) 4.0 100 3.0 2.5 2.0 1.5 1.0 10 8 6 4 2 0.5 0 25 50 75 100 125 150 TEMPERATURE (˚C) 100 200 300 400 500 600 700 800 900 FB PIN VOLTAGE (mV) 3685 G11 Soft-Start Minimum Switch On-Time 0 2.5 2 1.5 RUN/SS PIN VOLTAGE (V) 0.5 1 3 3.5 0 0 5 20 30 15 25 10 RUN/SS PIN VOLTAGE (V) 3685 G13 3685 G12 35 3685 G14 Error Amp Output Current Boost Diode 1.4 50 40 1.2 30 1.0 VC PIN CURRENT (μA) BOOST DIODE Vf (V) MINIMUM SWITCH ON TIME (ns) 400 3685 G10 140 0 600 25 50 75 100 125 150 TEMPERATURE (°C) 3685 G09 0 –50 –25 800 0 0.80 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) RT = 29.4k 0.8 0.6 0.4 20 10 0 –10 –20 –30 0.2 –40 0 0 0.5 1.0 1.5 BOOST DIODE CURRENT (A) 2.0 3685 G15 –50 –200 –100 100 0 FB PIN ERROR VOLTAGE (V) 200 3685 G16 3685fb 5 LT3685 TYPICAL PERFORMANCE CHARACTERISTICS Minimum Input Voltage 4.0 3.5 3.0 6.5 2.50 6.0 2.00 CURRENT LIMIT CLAMP VC VOLTAGE (V) INPUT VOLTAGE (V) INPUT VOLTAGE (V) 4.5 5.5 5.0 4.5 4.0 100 1000 LOAD CURRENT (A) VC Voltages Minimum Input Voltage 5.0 2.5 VOUT = 3.3V L = 4.7μH f = 800kHz 2.0 10 1 TA = 25°C unless otherwise noted. 10 1.00 SWITCHING THRESHOLD 0.50 VOUT = 5V L = 4.7μH f = 800kHz 1 10000 1.50 100 1000 LOAD CURRENT (A) 3685 G17 10000 0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3685 G19 3685 G18 Switching Waveforms; Discontinuous Operation Power Good Threshold Switching Waveforms; Continuous Operation THRESHOLD VOLTAGE (%) 95 VSW 5V/DIV VSW 5V/DIV 90 85 IL 0.5A/DIV IL 1A/DIV 80 VOUT 10mV/DIV VOUT 10mV/DIV 75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3685 G20 1μs/DIV VIN = 12V; FRONT PAGE APPLICATION ILOAD = 110mA 3685 G21 1μs/DIV VIN = 12V; FRONT PAGE APPLICATION ILOAD = 1A 3685 G22 3685fb 6 LT3685 PIN FUNCTIONS BD (Pin 1): This pin connects to the anode of the boost Schottky diode. BD also supplies current to the internal regulator. BOOST (Pin 2): This pin is used to provide a drive voltage, higher than the input voltage, to the internal bipolar NPN power switch. SW (Pin 3): The SW pin is the output of the internal power switch. Connect this pin to the inductor, catch diode and boost capacitor. VIN (Pin 4): The VIN pin supplies current to the LT3685’s internal regulator and to the internal power switch. This pin must be locally bypassed. RUN/SS (Pin 5): The RUN/SS pin is used to put the LT3685 in shutdown mode. Tie to ground to shut down the LT3685. Tie to 2.5V or more for normal operation. If the shutdown feature is not used, tie this pin to the VIN pin. RUN/SS also provides a soft-start function; see the Applications Information section. SYNC (Pin 6): This is the external clock synchronization input. Ground this pin when SYNC function is not used. Tie to a clock source for synchronization. Clock edges should have rise and fall times faster than 1μs. See synchronizing section in Applications Information. PG (Pin 7): The PG pin is the open collector output of an internal comparator. PG remains low until the FB pin is within 11% of the final regulation voltage. PG output is valid when VIN is above 3.6V and RUN/SS is high. FB (Pin 8): The LT3685 regulates the FB pin to 0.790V. Connect the feedback resistor divider tap to this pin. VC (Pin 9): The VC pin is the output of the internal error amplifier. The voltage on this pin controls the peak switch current. Tie an RC network from this pin to ground to compensate the control loop. RT (Pin 10): Oscillator Resistor Input. Connecting a resistor to ground from this pin sets the switching frequency. Exposed Pad (Pin 11): Ground. The Exposed Pad must be soldered to PCB. BLOCK DIAGRAM VIN 4 VIN C1 – + INTERNAL 0.79V REF 5 10 RUN/SS S SLOPE COMP BD SWITCH LATCH BOOST 6 2 C3 R RT OSCILLATOR 200kHz–2.4MHz Q S SW RT 1 SYNC L1 VOUT 3 C2 D1 SOFT-START 7 PG ERROR AMP + – + – 0.7V VC CLAMP VC 9 CC GND 11 FB RC CF 8 R2 R1 3685 BD 3685fb 7 LT3685 OPERATION The LT3685 is a constant frequency, current mode stepdown regulator. An oscillator, with frequency set by RT, enables an RS flip-flop, turning on the internal power switch. An amplifier and comparator monitor the current flowing between the VIN and SW pins, turning the switch off when this current reaches a level determined by the voltage at VC. An error amplifier measures the output voltage through an external resistor divider tied to the FB pin and servos the VC pin. If the error amplifier’s output increases, more current is delivered to the output; if it decreases, less current is delivered. An active clamp on the VC pin provides current limit. The VC pin is also clamped to the voltage on the RUN/SS pin; soft-start is implemented by generating a voltage ramp at the RUN/SS pin using an external resistor and capacitor. An internal regulator provides power to the control circuitry. The bias regulator normally draws power from the VIN pin, but if the BD pin is connected to an external voltage higher than 3V bias power will be drawn from the external source (typically the regulated output voltage). This improves efficiency. The RUN/SS pin is used to place the LT3685 in shutdown, disconnecting the output and reducing the input current to less than 1μA. The switch driver operates from either the input or from the BOOST pin. An external capacitor and diode are used to generate a voltage at the BOOST pin that is higher than the input supply. This allows the driver to fully saturate the internal bipolar NPN power switch for efficient operation. The oscillator reduces the LT3685’s operating frequency when the voltage at the FB pin is low. This frequency foldback helps to control the output current during startup and overload. The LT3685 contains a power good comparator which trips when the FB pin is at 89% of its regulated value. The PG output is an open-collector transistor that is off when the output is in regulation, allowing an external resistor to pull the PG pin high. Power good is valid when the LT3685 is enabled and VIN is above 3.6V. The LT3685 has an overvoltage protection feature which disables switching action when the VIN goes above 38V typical (36V minimum). When switching is disabled, the LT3685 can safely sustain input voltages up to 60V. 3685fb 8 LT3685 APPLICATIONS INFORMATION FB Resistor Network The output voltage is programmed with a resistor divider between the output and the FB pin. Choose the 1% resistors according to: ⎛ V ⎞ R1= R2 ⎜ OUT – 1⎟ ⎝ 0.79 V ⎠ Reference designators refer to the Block Diagram. Setting the Switching Frequency The LT3685 uses a constant frequency PWM architecture that can be programmed to switch from 200kHz to 2.4MHz by using a resistor tied from the RT pin to ground. A table showing the necessary RT value for a desired switching frequency is in Figure 1. SWITCHING FREQUENCY (MHz) RT VALUE (kΩ) 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 187 121 88.7 68.1 56.2 46.4 40.2 34 29.4 23.7 19.1 16.2 13.3 11.5 9.76 8.66 Figure 1. Switching Frequency vs. RT Value Operating Frequency Tradeoffs Selection of the operating frequency is a tradeoff between efficiency, component size, minimum dropout voltage, and maximum input voltage. The advantage of high frequency operation is that smaller inductor and capacitor values may be used. The disadvantages are lower efficiency, lower maximum input voltage, and higher dropout voltage. The highest acceptable switching frequency (fSW(MAX)) for a given application can be calculated as follows: fSW(MAX ) = VD + VOUT t ON(MIN) ( VD + VIN – VSW ) where VIN is the typical input voltage, VOUT is the output voltage, VD is the catch diode drop (~0.5V) and VSW is the internal switch drop (~0.5V at max load). This equation shows that slower switching frequency is necessary to safely accommodate high VIN/VOUT ratio. Also, as shown in the next section, lower frequency allows a lower dropout voltage. The reason input voltage range depends on the switching frequency is because the LT3685 switch has finite minimum on and off times. The switch can turn on for a minimum of ~150ns and turn off for a minimum of ~150ns. Typical minimum on time at 25°C is 80ns. This means that the minimum and maximum duty cycles are: DCMIN = fSW tON(MIN) DCMAX = 1– fSW tOFF(MIN) where fSW is the switching frequency, the tON(MIN) is the minimum switch on time (~150ns), and the tOFF(MIN) is the minimum switch off time (~150ns). These equations show that duty cycle range increases when switching frequency is decreased. A good choice of switching frequency should allow adequate input voltage range (see next section) and keep the inductor and capacitor values small. Input Voltage Range The maximum input voltage for LT3685 applications depends on switching frequency, the Absolute Maximum Ratings of the VIN and BOOST pins, and the operating mode. The LT3685 can operate from input voltages up to 38V, and safely withstand input voltages up 60V. Note that while VIN > 38V (typical), the LT3685 will stop switching, allowing the output to fall out of regulation. While the output is in start-up, short-circuit, or other overload conditions, the switching frequency should be chosen according to the following discussion. For safe operation at inputs up to 60V the switching frequency must be set low enough to satisfy VIN(MAX) ≥ 40V according to the following equation. If lower VIN(MAX) is desired, this equation can be used directly. 3685fb 9 LT3685 APPLICATIONS INFORMATION VIN(MAX ) = VOUT + VD –V +V fSW tON(MIN) D SW where VIN(MAX) is the maximum operating input voltage, VOUT is the output voltage, VD is the catch diode drop (~0.5V), VSW is the internal switch drop (~0.5V at max load), fSW is the switching frequency (set by RT), and tON(MIN) is the minimum switch on time (~150ns). Note that a higher switching frequency will depress the maximum operating input voltage. Conversely, a lower switching frequency will be necessary to achieve safe operation at high input voltages. If the output is in regulation and no short-circuit, startup, or overload events are expected, then input voltage transients of up to 60V are acceptable regardless of the switching frequency. In this mode, the LT3685 may enter pulse skipping operation where some switching pulses are skipped to maintain output regulation. In this mode the output voltage ripple and inductor current ripple will be higher than in normal operation. Above 38V switching will stop. The minimum input voltage is determined by either the LT3685’s minimum operating voltage of ~3.6V or by its maximum duty cycle (see equation in previous section). The minimum input voltage due to duty cycle is: VIN(MIN) = VOUT + VD –V +V 1– fSW tOFF(MIN) D SW where VIN(MIN) is the minimum input voltage, and tOFF(MIN) is the minimum switch off time (150ns). Note that higher switching frequency will increase the minimum input voltage. If a lower dropout voltage is desired, a lower switching frequency should be used. Inductor Selection For a given input and output voltage, the inductor value and switching frequency will determine the ripple current. The ripple current ΔIL increases with higher VIN or VOUT and decreases with higher inductance and faster switching frequency. A reasonable starting point for selecting the ripple current is: ΔIL = 0.4(IOUT(MAX)) where IOUT(MAX) is the maximum output load current. To guarantee sufficient output current, peak inductor current must be lower than the LT3685’s switch current limit (ILIM). The peak inductor current is: IL(PEAK) = IOUT(MAX) + ΔIL/2 where IL(PEAK) is the peak inductor current, IOUT(MAX) is the maximum output load current, and ΔIL is the inductor ripple current. The LT3685’s switch current limit (ILIM) is at least 3.5A at low duty cycles and decreases linearly to 2.5A at DC = 0.8. The maximum output current is a function of the inductor ripple current: IOUT(MAX) = ILIM – ΔIL/2 Be sure to pick an inductor ripple current that provides sufficient maximum output current (IOUT(MAX)). The largest inductor ripple current occurs at the highest VIN. To guarantee that the ripple current stays below the specified maximum, the inductor value should be chosen according to the following equation: ⎛ V +V ⎞⎛ V +V ⎞ L = ⎜ OUT D ⎟ ⎜ 1– OUT D ⎟ VIN(MAX ) ⎠ ⎝ fSW ΔIL ⎠ ⎝ where VD is the voltage drop of the catch diode (~0.4V), VIN(MAX) is the maximum input voltage, VOUT is the output voltage, fSW is the switching frequency (set by RT), and L is in the inductor value. The inductor’s RMS current rating must be greater than the maximum load current and its saturation current should be about 30% higher. For robust operation in fault conditions (start-up or short circuit) and high input voltage (>30V), the saturation current should be above 3.5A. To keep the efficiency high, the series resistance (DCR) should be less than 0.1 , and the core material should be intended for high frequency applications. Table 1 lists several vendors and suitable types. 3685fb 10 LT3685 APPLICATIONS INFORMATION Table 1. Inductor Vendors VENDOR URL PART SERIES Murata www.murata.com LQH55D Open TDK www.componenttdk.com SLF7045 SLF10145 Shielded Shielded Toko www.toko.com D62CB Shielded D63CB Shielded D75C Shielded D75F Open CR54 Open CDRH74 Shielded CDRH6D38 Shielded CR75 Open Sumida www.sumida.com TYPE Of course, such a simple design guide will not always result in the optimum inductor for your application. A larger value inductor provides a slightly higher maximum load current and will reduce the output voltage ripple. If your load is lower than 2A, then you can decrease the value of the inductor and operate with higher ripple current. This allows you to use a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. There are several graphs in the Typical Performance Characteristics section of this data sheet that show the maximum load current as a function of input voltage and inductor value for several popular output voltages. Low inductance may result in discontinuous mode operation, which is okay but further reduces maximum load current. For details of maximum output current and discontinuous mode operation, see Linear Technology Application Note 44. Finally, for duty cycles greater than 50% (VOUT/VIN > 0.5), there is a minimum inductance required to avoid subharmonic oscillations. See AN19. Input Capacitor Bypass the input of the LT3685 circuit with a ceramic capacitor of X7R or X5R type. Y5V types have poor performance over temperature and applied voltage, and should not be used. A 4.7μF to 10μF ceramic capacitor is adequate to bypass the LT3685 and will easily handle the ripple current. Note that larger input capacitance is required when a lower switching frequency is used. If the input power source has high impedance, or there is significant inductance due to long wires or cables, additional bulk capacitance may be necessary. This can be provided with a lower performance electrolytic capacitor. Step-down regulators draw current from the input supply in pulses with very fast rise and fall times. The input capacitor is required to reduce the resulting voltage ripple at the LT3685 and to force this very high frequency switching current into a tight local loop, minimizing EMI. A 4.7μF capacitor is capable of this task, but only if it is placed close to the LT3685 and the catch diode (see the PCB Layout section). A second precaution regarding the ceramic input capacitor concerns the maximum input voltage rating of the LT3685. A ceramic input capacitor combined with trace or cable inductance forms a high quality (under damped) tank circuit. If the LT3685 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the LT3685’s voltage rating. This situation is easily avoided (see the Hot Plugging Safety section). For space sensitive applications, a 2.2μF ceramic capacitor can be used for local bypassing of the LT3685 input. However, the lower input capacitance will result in increased input current ripple and input voltage ripple, and may couple noise into other circuitry. Also, the increased voltage ripple will raise the minimum operating voltage of the LT3685 to ~3.7V. Output Capacitor and Output Ripple The output capacitor has two essential functions. Along with the inductor, it filters the square wave generated by the LT3685 to produce the DC output. In this role it determines the output ripple, and low impedance at the switching frequency is important. The second function is to store energy in order to satisfy transient loads and stabilize the LT3685’s control loop. Ceramic capacitors have very low equivalent series resistance (ESR) and provide the best ripple performance. A good starting value is: COUT = 100 VOUT fSW 3685fb 11 LT3685 APPLICATIONS INFORMATION Table 2. Capacitor Vendors VENDOR PHONE URL PART SERIES Panasonic (714) 373-7366 www.panasonic.com Ceramic, COMMANDS Polymer, EEF Series Tantalum Kemet (864) 963-6300 www.kemet.com Ceramic, Tantalum Sanyo (408) 749-9714 www.sanyovideo.com T494, T495 Ceramic, Polymer, POSCAP Tantalum Murata (408) 436-1300 AVX www.murata.com Ceramic www.avxcorp.com Ceramic, Tantalum Taiyo Yuden (864) 963-6300 www.taiyo-yuden.com where fSW is in MHz, and COUT is the recommended output capacitance in μF. Use X5R or X7R types. This choice will provide low output ripple and good transient response. Transient performance can be improved with a higher value capacitor if the compensation network is also adjusted to maintain the loop bandwidth. A lower value of output capacitor can be used to save space and cost but transient performance will suffer. See the Frequency Compensation section to choose an appropriate compensation network. When choosing a capacitor, look carefully through the data sheet to find out what the actual capacitance is under operating conditions (applied voltage and temperature). A physically larger capacitor, or one with a higher voltage rating, may be required. High performance tantalum or electrolytic capacitors can be used for the output capacitor. Low ESR is important, so choose one that is intended for use in switching regulators. The ESR should be specified by the supplier, and should be 0.05 or less. Such a capacitor will be larger than a ceramic capacitor and will have a larger capacitance, because the capacitor must be large to achieve low ESR. Table 2 lists several capacitor vendors. TPS Series Ceramic where IOUT is the output load current. The only reason to consider a diode with a larger current rating than necessary for nominal operation is for the worst-case condition of shorted output. The diode current will then increase to the typical peak switch current. Peak reverse voltage is equal to the regulator input voltage. Use a Schottky diode with a reverse voltage rating greater than the input voltage. The overvoltage protection feature in the LT3685 will keep the switch off when VIN > 38V which allows the use of a 40V rated Schottky even when VIN ranges up to 60V. Table 3 lists several Schottky diodes and their manufacturers. Table 3. Diode Vendors PART NUMBER VR (V) IAVE (A) VF AT 1A (mV) VF AT 2A (mV) On Semicnductor MBRM120E MBRM140 20 40 1 1 530 550 595 Diodes Inc. B220 B230 DFLS240L 20 30 40 2 2 2 International Rectifier 10BQ030 20BQ030 30 30 1 2 500 500 500 420 470 470 Catch Diode The catch diode conducts current only during switch off time. Average forward current in normal operation can be calculated from: ID(AVG) = IOUT (VIN – VOUT)/VIN Ceramic Capacitors A precaution regarding ceramic capacitors concerns the maximum input voltage rating of the LT3685. A ceramic input capacitor combined with trace or cable inductance 3685fb 12 LT3685 APPLICATIONS INFORMATION The LT3685 uses current mode control to regulate the output. This simplifies loop compensation. In particular, the LT3685 does not require the ESR of the output capacitor for stability, so you are free to use ceramic capacitors to achieve low output ripple and small circuit size. Frequency compensation is provided by the components tied to the VC pin, as shown in Figure 2. Generally a capacitor (CC) and a resistor (RC) in series to ground are used. In addition, there may be lower value capacitor in parallel. This capacitor (CF) is not part of the loop compensation but is used to filter noise at the switching frequency, and is required only if a phase-lead capacitor is used or if the output capacitor has high ESR. Loop compensation determines the stability and transient performance. Designing the compensation network is a bit complicated and the best values depend on the application and in particular the type of output capacitor. A practical approach is to start with one of the circuits in this data sheet that is similar to your application and tune the compensation network to optimize the performance. Stability should then be checked across all operating conditions, including load current, input voltage and temperature. The LT1375 data sheet contains a more thorough discussion of loop compensation and describes how to test the stability using a transient load. Figure 2 shows an equivalent circuit for the LT3685 control loop. The error amplifier is a transconductance amplifier with finite output impedance. The power section, consisting of the modulator, power switch and inductor, is modeled as a transconductance amplifier generating an output current proportional to the voltage at the VC pin. Note that the output capacitor integrates this current, and that the capacitor on the VC pin (CC) integrates the error amplifier output current, resulting in two poles in the loop. In LT3685 CURRENT MODE POWER STAGE gm = 3.5mho SW ERROR AMPLIFIER OUTPUT R1 CPL FB gm = 420μmho + Frequency Compensation most cases a zero is required and comes from either the output capacitor ESR or from a resistor RC in series with CC. This simple model works well as long as the value of the inductor is not too high and the loop crossover frequency is much lower than the switching frequency. A phase lead capacitor (CPL) across the feedback divider may improve the transient response. Figure 3 shows the transient response when the load current is stepped from 500mA to 1500mA and back to 500mA. – forms a high quality (under damped) tank circuit. If the LT3685 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the LT3685’s rating. This situation is easily avoided (see the Hot Plugging Safely section). ESR 0.8V C1 + 3M C1 VC CF POLYMER OR TANTALUM GND RC CERAMIC R2 CC 3685 F02 Figure 2. Model for Loop Response VOUT 100mV/DIV IL 0.5A/DIV VIN = 12V; FRONT PAGE APPLICATION 10μs/DIV 3685 F03 Figure 3. Transient Load Response of the LT3685 Front Page Application as the Load Current is Stepped from 500mA to 1500mA. VOUT = 3.3V 3685fb 13 LT3685 APPLICATIONS INFORMATION BOOST and BIAS Pin Considerations Capacitor C3 and the internal boost Schottky diode (see the Block Diagram) are used to generate a boost voltage that is higher than the input voltage. In most cases a 0.22μF capacitor will work well. Figure 2 shows three ways to arrange the boost circuit. The BOOST pin must be more than 2.3V above the SW pin for best efficiency. For outputs of 3V and above, the standard circuit (Figure 4a) is best. For outputs between 2.8V and 3V, use a 1μF boost capacitor. A 2.5V output presents a special case because it is marginally adequate to support the boosted drive stage while using the internal boost diode. For reliable BOOST pin operation with 2.5V outputs use a good external Schottky diode (such as the ON Semi MBR0540), and a 1μF boost capacitor (see Figure 4b). For lower output voltages the boost diode can be tied to the input (Figure 4c), or to another supply greater than 2.8V. Tying BD to VIN reduces the maximum input voltage to 30V. The circuit in Figure 4a is more efficient because the BOOST pin current and BD pin quiescent current comes from a lower voltage source. You must also be sure that the maximum voltage ratings of the BOOST and BD pins are not exceeded. The minimum operating voltage of an LT3685 application is limited by the minimum input voltage (3.6V) and by the maximum duty cycle as outlined in a previous section. For proper startup, the minimum input voltage is also limited by the boost circuit. If the input voltage is ramped slowly, or the LT3685 is turned on with its RUN/SS pin when the output is already in regulation, then the boost capacitor may not be fully charged. Because the boost capacitor is charged with the energy stored in the inductor, the circuit will rely on some minimum load current to get the boost circuit running properly. This minimum load will depend on input and output voltages, and on the arrangement of the boost circuit. The minimum load generally goes to zero once the circuit has started. Figure 5 shows a plot of minimum load to start and to run as a function of input VOUT BD BOOST VIN VIN LT3685 GND 4.7μF C3 SW (4a) For VOUT > 2.8V VOUT D2 BD BOOST VIN VIN LT3685 GND 4.7μF C3 SW (4b) For 2.5V < VOUT < 2.8V VOUT BD BOOST VIN 4.7μF VIN LT3685 GND C3 SW 3685 FO4 (4c) For VOUT < 2.5V; VIN(MAX) = 30V Figure 4. Three Circuits For Generating The Boost Voltage voltage. In many cases the discharged output capacitor will present a load to the switcher, which will allow it to start. The plots show the worst-case situation where VIN is ramping very slowly. For lower start-up voltage, the boost diode can be tied to VIN; however, this restricts the input range to one-half of the absolute maximum rating of the BOOST pin. 3685fb 14 LT3685 APPLICATIONS INFORMATION 6.0 INPUT VOLTAGE (V) 5.5 TO START (WORST CASE) 5.0 15k 4.5 RUN/SS 4.0 TO RUN 0.22μF 3.5 3.0 2.0 10 1 VOUT 2V/DIV 2ms/DIV 100 1000 LOAD CURRENT (A) Figure 6. To Soft-Start the LT3685, Add a Resisitor and Capacitor to the RUN/SS Pin By choosing a large RC time constant, the peak start-up current can be reduced to the current that is required to regulate the output, with no overshoot. Choose the value of the resistor so that it can supply 20μA when the RUN/SS pin reaches 2.5V. TO START (WORST CASE) 6.0 5.0 TO RUN 4.0 VOUT = 5V TA = 25°C L = 8.2μH f = 700kHz 3.0 2.0 1 10 3685 F06 10000 8.0 7.0 VRUN/SS 2V/DIV GND VOUT = 3.3V TA = 25°C L = 8.2μH f = 700kHz 2.5 INPUT VOLTAGE (V) IL 1A/DIV RUN Synchronization 100 1000 LOAD CURRENT (A) 10000 3685 F05 Figure 5. The Minimum Input Voltage Depends on Output Voltage, Load Current and Boost Circuit At light loads, the inductor current becomes discontinuous and the effective duty cycle can be very high. This reduces the minimum input voltage to approximately 300mV above VOUT. At higher load currents, the inductor current is continuous and the duty cycle is limited by the maximum duty cycle of the LT3685, requiring a higher input voltage to maintain regulation. Soft-Start The RUN/SS pin can be used to soft-start the LT3685, reducing the maximum input current during start-up. The RUN/SS pin is driven through an external RC filter to create a voltage ramp at this pin. Figure 6 shows the startup and shut-down waveforms with the soft-start circuit. Synchronizing the LT3685 oscillator to an external frequency can be done by connecting a square wave (with 20% to 80% duty cycle) to the SYNC pin. The square wave amplitude should have valleys that are below 0.3V and peaks that are above 0.8V (up to 6V). The LT3685 may be synchronized over a 250kHz to 2MHz range. The RT resistor should be chosen to set the LT3685 switching frequency 20% below the lowest synchronization input. For example, if the synchronization signal will be 250kHz and higher, the RT should be chosen for 200kHz. To assure reliable and safe operation the LT3685 will only synchronize when the output voltage is near regulation as indicated by the PG flag. It is therefore necessary to choose a large enough inductor value to supply the required output current at the frequency set by the RT resistor. See Inductor Selection section. It is also important to note that slope compensation is set by the RT value: When the sync frequency is much higher than the one set by RT, the slope compensation will be significantly reduced which may require a larger inductor value to prevent subharmonic oscillation. 3685fb 15 LT3685 APPLICATIONS INFORMATION Shorted and Reversed Input Protection If the inductor is chosen so that it won’t saturate excessively, an LT3685 buck regulator will tolerate a shorted output. There is another situation to consider in systems where the output will be held high when the input to the LT3685 is absent. This may occur in battery charging applications or in battery backup systems where a battery or some other supply is diode OR-ed with the LT3685’s output. If the VIN pin is allowed to float and the RUN/SS pin is held high (either by a logic signal or because it is tied to VIN), then the LT3685’s internal circuitry will pull its quiescent current through its SW pin. This is fine if your system can tolerate a few mA in this state. If you ground the RUN/SS pin, the SW pin current will drop to essentially zero. However, if the VIN pin is grounded while the output is held high, then parasitic diodes inside the LT3685 can pull large currents from the output through the SW pin and the VIN pin. Figure 7 shows a circuit that will run only when the input voltage is present and that protects against a shorted or reversed input. D4 MBRS140 VIN VIN BOOST LT3685 RUN/SS VOUT SW VC GND FB BACKUP 3685 F07 Figure 7. Diode D4 Prevents a Shorted Input from Discharging a Backup Battery Tied to the Output. It Also Protects the Circuit from a Reversed Input. The LT3685 Runs Only When the Input is Present L1 C2 VOUT RRT CC RC R2 R1 D1 C1 GND RPG 3685 F08 VIAS TO LOCAL GROUND PLANE VIAS TO VOUT VIAS TO SYNC VIAS TO RUN/SS VIAS TO PG VIAS TO VIN OUTLINE OF LOCAL GROUND PLANE Figure 8. A Good PCB Layout Ensures Proper, Low EMI Operation by these components should be as small as possible. These components, along with the inductor and output capacitor, should be placed on the same side of the circuit board, and their connections should be made on that layer. Place a local, unbroken ground plane below these components. The SW and BOOST nodes should be as small as possible. Finally, keep the FB and VC nodes small so that the ground traces will shield them from the SW and BOOST nodes. The Exposed Pad on the bottom of the package must be soldered to ground so that the pad acts as a heat sink. To keep thermal resistance low, extend the ground plane as much as possible, and add thermal vias under and near the LT3685 to additional ground planes within the circuit board and on the bottom side. PCB Layout For proper operation and minimum EMI, care must be taken during printed circuit board layout. Figure 8 shows the recommended component placement with trace, ground plane and via locations. Note that large, switched currents flow in the LT3685’s VIN and SW pins, the catch diode (D1) and the input capacitor (C1). The loop formed Hot Plugging Safely The small size, robustness and low impedance of ceramic capacitors make them an attractive option for the input bypass capacitor of LT3685 circuits. However, these capacitors can cause problems if the LT3685 is plugged into a live supply (see Linear Technology Application Note 88 for 3685fb 16 LT3685 APPLICATIONS INFORMATION a complete discussion). The low loss ceramic capacitor, combined with stray inductance in series with the power source, forms an under damped tank circuit, and the voltage at the VIN pin of the LT3685 can ring to twice the nominal input voltage, possibly exceeding the LT3685’s rating and damaging the part. If the input supply is poorly controlled or the user will be plugging the LT3685 into an energized supply, the input network should be designed to prevent this overshoot. Figure 9 shows the waveforms that result when an LT3685 circuit is connected to a 24V supply through six feet of 24-gauge twisted pair. The first plot is the response with a 4.7μF ceramic capacitor at the input. The input voltage rings as high as 50V and the input current peaks at 26A. A good solution is shown in Figure 9b. A 0.7 resistor is added in series with the input to eliminate the voltage overshoot (it also reduces the peak input current). A 0.1μF capacitor improves high frequency filtering. For high input voltages its impact on efficiency is minor, reducing efficiency by 1.5 percent for a 5V output at full load operating from 24V. High Temperature Considerations The PCB must provide heat sinking to keep the LT3685 cool. The Exposed Pad on the bottom of the package must be soldered to a ground plane. This ground should be tied to large copper layers below with thermal vias; these layers will spread the heat dissipated by the LT3685. Place additional vias can reduce thermal resistance further. With these steps, the thermal resistance from die (or junction) to ambient can be reduced to JA = 35°C/W or less. With 100 LFPM airflow, this resistance can fall by another 25%. Further increases in airflow will lead to lower thermal resistance. Because of the large output current capability of the LT3685, it is possible to dissipate enough heat to raise the junction temperature beyond the absolute maximum of 125°C. When operating at high ambient temperatures, the maximum load current should be derated as the ambient temperature approaches 125°C. Power dissipation within the LT3685 can be estimated by calculating the total power loss from an efficiency measurement and subtracting the catch diode loss and inductor loss. The die temperature is calculated by multiplying the LT3685 power dissipation by the thermal resistance from junction to ambient. Other Linear Technology Publications Application Notes 19, 35 and 44 contain more detailed descriptions and design information for buck regulators and other switching regulators. The LT1376 data sheet has a more extensive discussion of output ripple, loop compensation and stability testing. Design Note 100 shows how to generate a bipolar output supply using a buck regulator. 3685fb 17 LT3685 APPLICATIONS INFORMATION CLOSING SWITCH SIMULATES HOT PLUG IIN VIN DANGER VIN 20V/DIV RINGING VIN MAY EXCEED ABSOLUTE MAXIMUM RATING LT3685 + 4.7μF LOW IMPEDANCE ENERGIZED 24V SUPPLY IIN 10A/DIV STRAY INDUCTANCE DUE TO 6 FEET (2 METERS) OF TWISTED PAIR 20μs/DIV (9a) 0.7Ω LT3685 VIN 20V/DIV + 0.1μF 4.7μF IIN 10A/DIV (9b) LT3685 + 22μF 35V AI.EI. 20μs/DIV VIN 20V/DIV + 4.7μF IIN 10A/DIV (9c) 20μs/DIV 3685 F09 Figure 9. A Well Chosen Input Network Prevents Input Voltage Overshoot and Ensures Reliable Operation when the LT3685 is Connected to a Live Supply 3685fb 18 LT3685 TYPICAL APPLICATIONS 5V Step-Down Converter VIN 6.8V TO 36V TRANSIENT TO 60V VIN ON OFF VOUT 5V 2A BD RUN/SS BOOST 0.47μF VC 4.7μF SW LT3685 D RT 16.2k L 6.8μH PG 40.2k SYNC 536k FB GND 470pF 22μF 100k f = 800kHz 3685 TA02 D: DIODES INC. DFLS240L L: TAIYO YUDEN NP06DZB6R8M 3.3V Step-Down Converter VIN 4.4V TO 36V TRANSIENT TO 60V VIN ON OFF VOUT 3.3V 2A BD RUN/SS BOOST 0.47μF VC 4.7μF LT3685 SW D RT 14k L 4.7μH PG 40.2k SYNC 470pF f = 800kHz 316k GND FB 22μF 100k 3685 TA03 D: DIODES INC. DFLS240L L: TAIYO YUDEN NP06DZB4R7M 3685fb 19 LT3685 TYPICAL APPLICATIONS 2.5V Step-Down Converter VIN 4V TO 36V TRANSIENT TO 60V VIN BD RUN/SS ON OFF D2 BOOST L 4.7μH 1μF VC 4.7μF LT3685 SW D1 RT 20k VOUT 2.5V 2A PG 215k SYNC 56.2k GND FB 330pF 47μF 100k f = 600kHz 3685 TA04 D1: DIODES INC. DFLS240L D2: MBR0540 L: TAIYO YUDEN NP06DZB4R7M 5V, 2MHz Step-Down Converter VIN 8.6V TO 22V TRANSIENT TO 36V VIN ON OFF VOUT 5V 2A BD RUN/SS BOOST 0.47μF VC 2.2μF LT3685 SW D RT 14k L 2.2μH PG 11.5k SYNC 470pF f = 2MHz 536k GND FB 22μF 100k 3685 TA05 D: DIODES INC. DFLS240L L: SUMIDA CDRH4D22/HP-2R2 3685fb 20 LT3685 TYPICAL APPLICATIONS 12V Step-Down Converter VIN 15V TO 36V TRANSIENT TO 60V* VIN ON OFF VOUT 12V 2A BD RUN/SS BOOST 0.47μF VC 10μF SW LT3685 D RT 26.1k L 10μH PG 40.2k 715k SYNC FB GND 330pF 22μF 50k f = 800kHz 3685 TA06 D: DIODES INC. DFLS240L L: NEC/TOKIN PLC-0755-100 *USE SCHOTTKY DIODE RATED AT VR >45V. 1.8V Step-Down Converter VOUT 1.8V 2A VIN 3.5V TO 27V VIN ON OFF BD RUN/SS BOOST 0.47μF VC 4.7μF LT3685 SW D RT 18.2k L 3.3μH PG 68.1k SYNC 330pF f = 500kHz 127k GND FB 47μF 100k 3685 TA08 D: DIODES INC. DFLS240L L: TAIYO YUDEN NP06DZB3R3M 3685fb 21 LT3685 PACKAGE DESCRIPTION DD Package 10-Lead Plastic DFN (3mm × 3mm) (Reference LTC DWG # 05-08-1699) R = 0.115 TYP 6 0.38 p0.10 10 0.675 p0.05 3.50 p0.05 1.65 p0.05 2.15 p0.05 (2 SIDES) 3.00 p0.10 (4 SIDES) PACKAGE OUTLINE 1.65 p0.10 (2 SIDES) PIN 1 TOP MARK (SEE NOTE 6) (DD) DFN 1103 5 0.200 REF 0.25 p0.05 0.50 BSC 2.38 p0.05 (2 SIDES) 1 0.25 p0.05 0.50 BSC 0.75 p0.05 0.00 – 0.05 2.38 p0.10 (2 SIDES) BOTTOM VIEW—EXPOSED PAD RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2). CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3685fb 22 LT3685 PACKAGE DESCRIPTION MSE Package 10-Lead Plastic MSOP (Reference LTC DWG # 05-08-1663) BOTTOM VIEW OF EXPOSED PAD OPTION 2.794 p 0.102 (.110 p .004) 5.23 (.206) MIN 0.889 p 0.127 (.035 p .005) 1 2.06 p 0.102 (.081 p .004) 1.83 p 0.102 (.072 p .004) 2.083 p 0.102 3.20 – 3.45 (.082 p .004) (.126 – .136) 10 0.50 0.305 p 0.038 (.0197) (.0120 p .0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT 3.00 p 0.102 (.118 p .004) (NOTE 3) 10 9 8 7 6 3.00 p 0.102 (.118 p .004) (NOTE 4) 4.90 p 0.152 (.193 p .006) 0.254 (.010) DETAIL “A” 0o – 6o TYP 1 2 3 4 5 GAUGE PLANE 0.53 p 0.152 (.021 p .006) DETAIL “A” 0.18 (.007) 0.497 p 0.076 (.0196 p .003) REF SEATING PLANE 0.86 (.034) REF 1.10 (.043) MAX 0.17 – 0.27 (.007 – .011) TYP 0.50 (.0197) BSC 0.1016 p 0.0508 (.004 p .002) MSOP (MSE) 0307 REV B NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 3685fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 23 LT3685 TYPICAL APPLICATION 1.2V Step-Down Converter VOUT 1.2V 2A VIN 3.6V TO 27V VIN ON OFF BD RUN/SS BOOST 0.47μF VC 4.7μF LT3685 SW D RT 16.2k L 3.3μH PG 68.1k 52.3k SYNC GND FB 330pF 100k 47μF f = 500kHz 3685 TA09 D: DIODES INC. DFLS240L L: TAIYO YUDEN NP06DZB3R3M RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1933 500mA (IOUT), 500kHz Step-Down Switching Regulator in SOT-23 VIN: 3.6V to 36V, VOUT(MIN) = 1.2V, IQ = 1.6mA, ISD <1μA, ThinSOT Package LT3437 60V, 400mA (IOUT), MicroPower Step-Down DC/DC Converter with Burst Mode VIN: 3.3V to 80V, VOUT(MIN) = 1.25V, IQ = 100μA, ISD <1μA, 10-Pin 3mm x 3mm DFN and 16-Pin TSSOP Packages LT1936 36V, 1.4A (IOUT), 500kHz High Efficiency Step-Down DC/DC Converter VIN: 3.6V to 36V, VOUT(MIN) = 1.2V, IQ = 1.9mA, ISD <1μA, MS8E Package LT3493 36V, 1.2A (IOUT), 750kHz High Efficiency Step-Down DC/DC Converter VIN: 3.6V to 40V, VOUT(MIN) = 0.8V, IQ = 1.9mA, ISD <1μA, 6-Pin 2mm x 3mm DFN Package LT1976/LT1977 60V, 1.2A (IOUT), 200kHz/500kHz, High Efficiency StepDown DC/DC Converter with Burst Mode VIN: 3.3V to 60V, VOUT(MIN) = 1.2V, IQ = 100μA, ISD <1μA, 16-Pin TSSOP Package LT1767 25V, 1.2A (IOUT), 1.1MHz, High Efficiency Step-Down DC/DC Converter VIN: 3V to 25V, VOUT(MIN) = 1.2V, IQ = 1mA, ISD <6μA, MS8E Package LT1940 Dual 25V, 1.4A (IOUT), 1.1MHz, High Efficiency Step-Down DC/DC Converter VIN: 3.6V to 25V, VOUT(MIN) = 1.2V, IQ = 3.8mA, ISD <30μA, 16-Pin TSSOP Package LT1766 60V, 1.2A (IOUT), 200kHz, High Efficiency Step-Down DC/DC Converter VIN: 5.5V to 60V, VOUT(MIN) = 1.2V, IQ = 2.5mA, ISD = 25μA, 16-Pin TSSOP Package LT3434/LT3435 60V, 2.4A (IOUT), 200/500kHz, High Efficiency Step-Down DC/DC Converter with Burst Mode VIN: 3.3V to 60V, VOUT(MIN) = 1.2V, IQ = 100μA, ISD <1μA, 16-Pin TSSOP Package LT3480 38V, 2A (IOUT), 2.4MHz, High Efficiency Step-Down DC/DC VIN: 3.6V to 38V, VOUT(MIN) = 0.79V, IQ = 70μA, ISD <1μA, 10-Pin 3mm x Converter with Burst Mode 3mm DFN and 10-Pin MSOP Packages LT3481 36V, 2A (IOUT), 2.8MHz, High Efficiency Step-Down DC/DC VIN: 3.6V to 34V, VOUT(MIN) = 1.26V, IQ = 50μA, ISD <1μA, 10-Pin 3mm x Converter with Burst Mode 3mm DFN and 10-Pin MSOP Packages LT3684 36V, 2A (IOUT), 2.8MHz, High Efficiency Step-Down DC/DC Converter VIN: 3.6V to 34V, VOUT(MIN) = 1.26V, IQ = 1.5mA, ISD <1μA, 10-Pin 3mm x 3mm DFN and 10-Pin MSOP Packages 3685fb 24 Linear Technology Corporation LT 1208 REV B • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2007