Thermal Analysis and Reliability of WIRE BONDED ECL

AND8072/D
Thermal Analysis
and Reliability of
WIRE BONDED ECL
Prepared by: Paul Shockman
ON Semiconductor Logic Applications Engineering
http://onsemi.com
APPLICATION NOTE
WIRE BONDED Device Failure Mechanisms
For the plastic DIP, SOIC, TSSOP, PLCC, TQFP, and
other “WIRE BONDED” device packages, the dominant
mode of failure is related to gold wire connecting the die
pads to corresponding pin leads.
A good, operational wire bond electrically connects a
package lead to the appropriate die circuit contact. Gold wire
is used in the fabrication of die bond wire connecting a die
pad to the package lead as shown in Figure 1, Typical
“WIRE BONDED” Integrated Circuit Bond Wire
Connect Diagram. Each gold wire is bonded at one end to
the silicon circuit die at an aluminum pad, usually located
near an outer edge. The other gold wire end is bonded to a
device lead.
The very dominant mode of failure (>99.99% occurrence)
related to operational lifetime in devices has been found
historically to be die wire continuity, or “Opens”. Device
reliability theoretically follows a characteristic “bathtub”
shaped curve consisting of:
1. High early failure rate attributed to defects and
flaws in process and assembly,
2. Low rate during the operation lifetime due to die
wire continuity,
3. High terminal rate associated with junction
wearout.
INTRODUCTION
Normal operation of Integrated Circuits will cause
electrical power, P, to be converted into heat by the die
circuitry and thermally dissipated into adjacent materials.
As the electrical system generates heat and the physical
system thermally dissipates this heat, an operational
equilibrium is reached after a stabilization period. This
stable, operational junction temperature of the Integrated
Circuit die is represented as Theta J or TJ, and is measured
with reference to the temperature of ambient air, TA.
Heat evolved in the electrical energy conversion by the die
circuit (TJ) must be conducted away and dissipated by:
1. Conduction through the package case and
connections into the printed circuit board
2. Conduction through the package case and
connections into air
3. Radiance
The consequent local rise in temperature of the internal
die accelerates failure mechanisms responsible for the
eventual functional non−operation of the Integrated Circuit.
These failure mechanisms predominantly determine the
reliability of the Integrated Circuit and subsequent
operational lifetime.
Factors affecting this failure mechanism and
determination of the device reliability will be analyzed and
discussed. Control and influence of some of the factors by
the System Designer offer opportunities for increasing
reliability and extending operational lifetime.
Au BONDING WIRE
Au BONDING WIRE
Al PAD
A
A
A
A
A
TOP VIEW
A
LEAD
END VIEW
LEAD
SILICON DIE
(End View Cross−section, not to scale)
Figure 1. Typical Integrated Circuit Bond Wire Connect Diagram
© Semiconductor Components Industries, LLC, 2010
August, 2010 − Rev. 5
1
Publication Order Number:
AND8072/D
AND8072/D
altering and raising the resistivity higher than the remaining
pure gold segment, leading to localized heating. Aluminum
migration accelerates with local temperature increase,
concentrating the contamination. This failure process
continues the thermal cascade until melting of the bonding
wire occurs and opens the wire connection. When a gold
bond wire fails, the discontinuity is usually located close to
the aluminum die pad.
Normal operation of an integrated circuit device elevates
the temperature of the device system, including die,
aluminum pad, gold bond wires, device, board, and
environment (air). It is the thermal elevation of die junction
transferred from die to bond wires which causes aluminum
from the die bond pad to migrate into the gold wire
proportional to both temperature elevation and the duration
of time elevated. The resultant intermetallic “gold−
aluminum” contaminates a segment of the bond wire
FAIL POINT
GOLD
Al
ALUMINUM BOND PAD
DIE
Figure 2. Aluminum Migration from the Die Bond Pad into the Gold Wire
Bond Failure Rate
Device failure rate is benchmarked at 0.1%, or 1 bond
failure per 1000 bonds in Reliability calculations. This is
based on the special Arrhenius equation (Eq. 1) expressing
junction temperature as the bond failure rate benchmark of
0.1%:
Thours + (6.376
10
*9
)ȏ
[11554.267 / (273.15+TJ )]
Table 1. TJ VERSUS TIME TO 0.1% BOND FAILURE
TJ, Junction
Temperature (°C)
Time (Hours)
Time (Years)
80
1,032,200
117.8
90
419,300
47.9
100
178,700
20.4
110
79,600
9.1
120
37,000
4.2
130
17,800
2.0
140
8,900
1.0
(Eq. 1)
Where:
Thours = Time in hours to 0.1% bond
TJ = Device junction temperature °C.
Operational Lifetime and Maximum Acceptable
Junction Temperature
The bond failure rate equation above renders a table of
operational device lifetimes based on various junction
temperatures (see Table 1: TJ versus Time to 0.1% Bond
Failure. The maximum acceptable junction temperature is
considered to be 140°C, since this predicts the 0.1% bond
failure rate occurs after 8,900 hours, or one year of
continuous service. The determination of TJ indicates
operational device lifetime.
Junction Temperature Determination
Operating die junction temperature results from the total
electrical power converted on chip, PD, and the total
physical thermal transfer resistance to ambient temperature
TA. This thermal resistance from the die to ambient
temperature is defined as JA, according to equation
Equation 2:
TJ + (PD)(JA) ) TA
(Eq. 2)
Where:
TJ is junction temperature
TA is ambient air temperature
PD is device total power dissipation
JA is device thermal resistance, junction to ambient
The operating lifetime is determined by selecting TJ in
Equation 2. The Power Dissipation, PD, and Thermal
Resistance, JA in Equation 2 will be discussed as sections:
SECTION 1: PD, Power Conversion Dissipation
SECTION 2: JA, Device Thermal Resistance,
SECTION 2: Junction to Ambient
TA, Ambient Air Temperature
http://onsemi.com
2
AND8072/D
SECTION 1
PD, POWER DISSIPATION
The total device power dissipation, SPD, is calculated from
summing the internal device electrical power conversions:
PDstatic, PDoutput, and possibly PdRterm(internal) found on
some devices. Refer to Figure 3: PD, Device Power
Dissipation, and Equation 3. Note the device input currents
are not considered due to their very small magnitudes.
PD + PDstatic ) PDoutput ) PdRterm *
(Eq. 3)
Where:
PDstatic + (IEE
|VCC * VEE|)
PDoutput + (I(output) 2
(Eq. 4)
Z(output))
(Eq. 5)
* PdRterm(internal) + (PdVIH ) PdVIL)
(Eq. 6)
(* if present internally on the inputs)
VCC+
PDstatic
Iinput
PDoutput
PDinput
Rstatic
Zinput
PdRterm*
Rterm*
(internal)
(internal)
Ioutput
Zoutput
EXTERNAL
TERMINATION
SCHEME
Rterm
Iin(term)*
Iterm
DEVICE PACKAGE
VEE−
IEE
(* if present)
VEE−
Figure 3. PD, Device Power Dissipation
http://onsemi.com
3
AND8072/D
SPDstatic: STATIC POWER DISSIPATION:
PDstatic + (IEE
|VCC * VEE|)
An example would be the PDstatic of MC100EL91,
operating from a VCC of 5.0 V and a VEE of −5.0 V:
(Eq. 4)
PDstatic + PD1 ) PD2 ) AAA
+ 55 mW ) 140 mW
+ 190 mW
The first internal power conversion, SPDstatic (Eq. 4),
typically represents the product of a spec current, IEE, and
the voltage potential developed across the two power
supplies, the (more) positive supply: VCC; and the (more)
negative supply, VEE. IEE does not include output or load
currents and varies little across the operating frequency
range. As stated within the Data Sheet limit tables, there is
a min and max. Output currents can vary from zero (open)
to the pin limit (50 mA) depending on the termination in use.
For example, the PDstatic of MC10LVEP16 operating
from a VCC of 2.5 V and VEE of 0.0 V:
Where:
PD1 + (ICC |VCC * GND|)
+ 11 mA 5.0 V
+ 55 mW
PD2 + (IEE |GND * VEE|)
+ 28 mA 5.0 V
+ 140 mW
PDstatic + (IEE |VCC * VEE|)
+ 22 mA 5.0 V
+ 110 mW
Of course, the PDstatic of MC100EL91 must be summed
with the PDoutput per Eq. 3 to determine PD.
Non−ECL Circuitry
When any non−ECL output circuitry is present, such as in
the TTL and LVTTL/LVCMOS translators, both the static
ECL and non−ECL type dissipation contributions to
PDstatic must be separately determined and summed as
Eq. 4c:
Of course, the PDstatic of MC10LVEP16 must be summed
with the PDoutput to determine PD as per Eq. 3.
Some devices (such as LVEL90, LVEL91, E1651, E1652,
etc.) will require three unique supplies (VCC, GND, & VEE
or VCC1, VCC2, & VEE) and will specify two unique
currents, I1 and I2, as indicated in Equation 4a.
PDstatic + PD1 ) PD2 ) AAA
PDstatic + (I1
(I2
|VCC1 * VEE1|) )
|VCC2 * VEE2|) ) AAA
(Eq. 4a)
PDstatic + PDstatic(ECL) ) PDstatic(non−ECL) (Eq. 4c)
(Eq. 4b)
An example would be the PDstatic of the TTL output
translator, MC100EPT25, operating from a VCC of 3.3 V, a
VEE of −5.0 V, and a GND of 0.0 V. A signal duty cycle of
50% is assumed and typical currents:
Spec currents may be from VCC1 to GND, VCC2 to GND,
or from GND to VEE. Refer to Figure 4: Power Currents
in Three Supply Devices. Each current and respective
voltage potential will determine a power conversion
dissipation. All dissipations must be summed for the total
power dissipation.
VCC
VCC1
Where:
PDstatic(ECL) + (IEE |GND * VEE|)
+ 16 mA 5.0 V
+ 80 mW
VCC2
ICC1
ICC
PDstatic + PDstatic(ECL) ) PDstatic(non−ECL)
+ 80 mW ) 55 mW
+ 135 mW
ICC2
PDstatic(non−ECL) + ((ICCH ) ICCL)ń2)
+ 22ń2 mA 5.0 V
+ 55 mW
GND
IEE
VEE
(|VCC−GND|)
…and of course, the PDstatic of MC100EPT25 must be
summed with the PDoutput per Eq. 3 to determine PD.
VEE
Figure 4. Power Currents in Three Supply Devices
http://onsemi.com
4
AND8072/D
PDoutput: OUTPUT STRUCTURE POWER
DISSIPATION:
PDoutput + (I(output)
Ioutput(typ) + ǒ(2.4 ) 1.6)ń2Ǔń150 ohms
+ 13.3 mA
V(output)) )
(Eq. 5)
(Eq. 5b)
The 13.3 mA average current applies to both lines in the
differential pair, creating an average total of 26.6 mA,
typical Ioutput.
This single line average of 13.3 mA Ioutput current passing
through the internal output transistor generating PDoutput.
PD(dynamic) = f * Cload * Vswing ^ 2 ; usually neglected.
Substituting the termination current from Eq. 5b into Eq. 5,
and using typical VOH of 2.4 V and a VOL of 1.6 V, then
yields the nominal power dissipation for a single output line:
PD(dynamic)
Where:
V(output) is VOH or VOL
I(output) = V(output) / Zterm
The device electrical power conversion, PDoutput, results
from the output termination current, Ioutput flowing through
the output structure, Zoutput, per Figure 5: Typical ECL
Output. An ECL OUTPUT structure has 6 to 8 ohms
internal impedance, whereas the internal impedance of a
TTL output structure may vary considerably.
+ 0.013 ((3.3 * 2.4) ) (3.3 * 1.6)ń2) + 16.9 mW
or 33.8 mW per diff pair.
In a typical MC100LVEP16, VCC = 2.5, VEE = 0.0, at
85°C, with Zterm = 100 ohms, the internal single output line
generates PDoutput per Eq. 5 and 5a:
VCC
Zoutput
6 to 8 Ohms
PDoutput + (I(output) V(output)
+ (((VOH ) VOL)ń2)ńZterm)
Ioutput
INTERNAL
+ (((1.6 ) 0.8)ń2)ń100)
Zterm
((1.6 ) 0.8)ń2)
+ 14.4 mW
per line or 28.8 mW per diff pair.
VEE
Figure 5. Typical ECL Output
The MC100LVEP16 PDstatic, of course, must be
summed with the PDoutput per Eq. 3 to determine PD.
Only the internal heat associated with the output structure,
PDoutput is added to the total thermal load as Ioutput current
passing through the Zterm dissipates heat externally. Of
course, the physical location of Zterm heat could affect a
device’s total thermal management. Note the device’s input
currents are not considered due to their very small
magnitudes.
An average single output line current, Ioutput, may be
calculated using Zterm, (the external user selected
termination), spec output voltages (VOH and VOL) as shown
in Eq. 5a. and frequency.
Duty cycle (HIGH to LOW level ratio) in a single line is
a co−factor, but assuming the signal is 50%, then:
Ioutput(typ) + ǒ(VOH ) VOL)ń2ǓńZterm
((VOH ) VOL)ń2)
Non ECL PDoutput
A non ECL output is typically not subjected to ECL
termination schemes. Still, the total PDoutput (TTL) thermal
contribution to the device may be calculated from the Output
current (Ioutput) and the output impedance Zoutput per Eq. 5.
Generally, a TTL Z(output) is about 30 ohms in the High and
5 ohms when Low. A notable exception is the
MC10/100H646 with about 7 ohm (internal output)
impedance for both HIGH and LOW states. The
MC10/100H646 output is designed to terminate with a
series 43 ohm resistor in 50 ohm impedance traces. Power
calculations over the frequency range is indicated in the
MC10/100H646 data sheet (Figure 2).
The device PDoutput may be determined as:
(Eq. 5a)
Where:
VOH = spec Voltage Output High
VOL = spec Voltage Output LOW
Zterm = termination impedance
In the differential pair termination, the two lines will
essentially be in complimentary states, but the average
current in a differential pair is 2X a single line. For example,
consider the MC10EP016 TCbar output (pin 12) and:
1. VCC = 3.3,
2. VEE = 0.0,
3. 85°C,
4. Zterm = 150 Ohms
generates an Ioutput:
PDoutput + f * Cload * Vswing 2
(Eq. 7)
Where:
Vswing = signal VOH − VOL
f = frequency
Cload = load capacitance
This is multiplied by the number of outputs for total
PDoutput. The PD results from the sum of PDstatic with the
PDoutput per Eq. 3.
PdRterm(internal): (if present) INPUT Rterm POWER
DISSIPATION:
PdRterm + (PdVIH ) PdVIL)
http://onsemi.com
5
(Eq. 6)
AND8072/D
Where:
PdVIH = Iterm * VIH
PdVIL = Iterm * VIL
The Rterm power dissipation, PdRterm, results from signal
currents through internal impedance matching resistors of
50 ohms, located internally. Two configurations are in use:
1. Internal Termination Combo Pin (see Figure 6)
2. Internal Termination Singulated Pins (see Figure 7)
When VCC = 3.3 V, the VTT = 1.3 V, and when typical
LVPECL levels of VIH = 2.4 V & VIL 1.6 V, are applied:
PdVIH + ǒ(2.4 * 1.3)ń50Ǔ * (2.4 * 1.3)
+ (1.1ń50) * 1.1
+ 24.2 mW
PdVIL + ǒ(1.6 * 1.3)ń50Ǔ * (1.6 * 1.3)
+ (0.3ń50) * 0.3
+ 9.8 mW
PdRterm + 24.2 ) 9.8 + 34 mW
Rt
With standard (800 mV) signal amplitude, this value does
not change with VCC, since VTT voltage remains referenced
to VCC.
The second configuration, Figure 7: Internal Termination
Singulated, allow greater circuit versatility but still
dissipates a thermal contribution to the device according to:
PdRterm = Iterm * Vterm
Where:
Iterm = (Vin − Vt) / Rt
Vterm = Vin − Vt
Rt
Vt
Figure 6. Internal Termination Combo Pin
When the Internal Termination Combo pin, Vt, of
Figure 6 is connected to a VTT sinking power supply
(VCC − 2.0 V) and a signal, VIH to VIL, is applied, the
internal resistors will draw current according to the
equations:
IVIH = (VIH − VTT)/ Rt
IVIL = (VIL − VTT)/ Rt
The Rt values are 50 ohms and VTT = VCC − 2.0 V:
PdVIH +
(Iterm)(VIH)
@ (VIH(VCC * 2.0))
50
PdVIL +
(Iterm)(VIL)
@ (VIL(VCC * 2.0))
50
Rt1
Rt2
Vt1
Vt2
Figure 7. Internal Termination Singulated
http://onsemi.com
6
AND8072/D
SECTION 2
qJA
As per Eq. 2, the qJA is multiplied by the total power
dissipated, PD, then added to the ambient air temperature,
TA, to determine TJ, junction temperature.
TJ = (PD) (JA) + TA
The following table lists the junction to ambient and
junction to case temperature rise for several device
packages.
Table 2. PACKAGE THERMAL CHARACTERISTICS
Package
Leads
Case
qJA Still Air 0.0 LFPM
(°C/W)
qJA 500 LFPM (°C/W)
FCBGA
16
489
149
127
TSSOP
8
948R
185
140
41−44
16
948F
138
108
33−36
20
948E
90
60
30−35
28
948A
76
60
25
8
751
190
130
41−44
16
751B
100
60
33−36
20 WIDE
751D
90
60
30−35
20
775
35
42
28
776
63.5
43.5
16
648
80
50
24
724
75
50
MICRO−10
10
846B
177
132
DFN
8
506AA
129
84
QFN
16
485G
42
35
4
20
485E
47
33
18
24
485L
37
32
11
32
488AM
31
27
12
52
485M
25
19.6
21
32
873A
74
61
12−17
52
848D
35.6
30
21
64
848G
35.6
30
3.2−6.4
SOIC
PLCC
DIL
LQFP
qJC Std. Bd. (°C/W)
22*26
40
*See Appendix A
GREEN Stand−by Mode in NECL:
Standard “two−supply” ECL devices using VCC and VEE,
may, in NECL mode only, safely conserve system power
consumption during non−functional periods by shutting
down the VEE (Negative) supply (to 0.0 V) with no ill
effects. This is NOT acceptable for devices operating in
PECL or LVPECL mode.
− package leads and mounts heat conduction
− (i.e. soldered versus non−soldered)
− copper traces conduction and area
− thermally conductive adhesive
2. Board material thermal conduction
− planes thickness, material, and thermal transfer
3. Device locations and topology on board
4. Airflow:
− forced−air (temperature, humidity, velocity)
− parallel verses transverse
− turbulence
− blockages
5. Heat sinks (external)
System Considerations:
The following items are mentioned as other potential
issues when determining a complete thermal performance
and behavior for a board or system, although a detailed
consideration of each will not be present:
1. Package mount:
http://onsemi.com
7
AND8072/D
Appendix A:
For the 52 TQFP (MC100LVE222) in 0 l fpm (still air):
JA is considered to be between 69−71°C/W
JC is considered to be between 8.1 (Oil Bath Immersion
Method) and 15 (Top Center Probe Method) °C/W.
Any heat sink calculations should be based on the Top
Center Probe Method values.
JC of a 52 TQFP?
Thermal analysis of the 52 TQFP was conducted on a one
layer copper clad (0.035″, “1 oz.” type) FR4 fiberglass
board, 3″ X 3″ X 0.0625″, 27 mil traces, with devices
soldered in place.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
8
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
AND8072/D