UM1036
User manual
2 kW 3-phase motor control STEVAL-IHM028V2 evaluation board
featuring the IGBT intelligent power module STGIPS20C60
Introduction
This document describes the 2 kW 3-phase motor control evaluation board featuring the
IGBT intelligent power module STGIPS20C60. The evaluation board is an AC-DC inverter
that generates a 3-phase waveform for driving 3-phase motors such as induction motors or
permanent magnet synchronous motors (PMSM) up to maximal 2000 W with or without
sensors.
The main device presented in this user manual is a universal, fully evaluated and populated
design consisting of a 3-phase inverter bridge based on the 600 V IGBT power module in
the SDIP 25L package mounted on a heatsink. The IGBT power module integrates all power
IGBT switches with freewheeling diodes together with high voltage gate drivers. Thanks to
this integrated module, the system has been specifically designed to achieve power
inversion in a reliable and compact design. Such integration saves PCB space occupation
and assembly costs, together with high reliability due to the design simplicity.
The board is designed to be compatible with single-phase mains, supplying from 90 VAC to
285 VAC or from 125 VDC up to 400 VDC for the DC voltage.
This document is associated with the release of the STEVAL-IHM028V2 evaluation board
(see Figure 1).
Figure 1. STEVAL-IHM028V2
November 2014
DocID18293 Rev 2
1/47
www.st.com
Contents
UM1036
Contents
1
2
3
System introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1
Main characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2
Target application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3
Safety and operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3.1
General terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3.2
Eevaluation board intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3.3
Evaluation board installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3.4
Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Board description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1
System architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2
Board schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3
Circuit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.3.1
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.3.2
Inrush limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.3.3
Power block based on IGBT module . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.3.4
Brake function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.3.5
Overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.3.6
Current sensing amplifying network . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.3.7
The tachometer and Hall/encoder inputs . . . . . . . . . . . . . . . . . . . . . . . . 20
2.3.8
Temperature feedback and overtemperature protection (OTP) . . . . . . . 20
2.3.9
Active heatsink cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Hardware setting of the STEVAL-IHM028V2 . . . . . . . . . . . . . . . . . . . . . 23
3.1
Hardware settings for six-step (block commutation) current control in singleshunt configuration 23
3.2
Hardware settings for FOC in three-shunt configuration . . . . . . . . . . . . . 24
3.3
Hardware settings for FOC in single-shunt configuration . . . . . . . . . . . . . 25
4
Testing of the evaluation board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5
Description of jumpers, test pins, and connectors . . . . . . . . . . . . . . . 29
6
Connector placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2/47
DocID18293 Rev 2
UM1036
Contents
7
Bill of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
8
PCB layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
9
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
10
Using STEVAL-IHM028V2 with STM32 FOC firmware library . . . . . . . 43
10.1
Environmental considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
10.2
Hardware requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
10.3
Software modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11
Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
12
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
13
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
DocID18293 Rev 2
3/47
47
System introduction
UM1036
1
System introduction
1.1
Main characteristics
The information listed below shows the converter specification data and the main
parameters set for the STEVAL-IHM028V2 evaluation board.
•
Minimum input voltage 125 VDC or 90 VAC
•
Maximum input voltage 400 VDC or 285 VAC
•
With applied input voltage doubler - the range from 65 VAC to 145 VAC
•
Maximum output power for applied motor up to 2000 W
•
Regenerative brake control feature
•
Input inrush limitation with bypassing relay
•
+15 V auxiliary power supply based on a buck converter with VIPer™26
•
Using IGBT intelligent power module STGIPS20C60 in SDIP 25L molded package
•
Fully populated board conception with test points and safety isolated plastic cover
•
Motor control connector for interface with STM3210B-EVAL board, STM8/128-EVAL
board, and other ST motor control dedicated kits
•
Tachometer input
•
Hall/encoder inputs
•
Overheating protection
•
Active fan cooling of heatsink with automatic temperature switch
•
Possibility to connect MB843 BLDC daughterboard for sensor-less six-step control
•
PCB type and size:
–
Material of PCB - FR-4
–
Double-sided layout
–
Copper thickness: ~60 μm
Total dimensions of evaluation board: 195 mm x 175 mm.
1.2
4/47
Target application
•
Power fans for HVAC application
•
Power tools
•
Industrial drives
•
High-power industry pumps
•
Professional washing machines.
DocID18293 Rev 2
UM1036
System introduction
1.3
Safety and operating instructions
1.3.1
General terms
Warning:
During assembly, testing, and normal operation, the
evaluation board poses several inherent hazards, including
bare wires, moving or rotating parts, and hot surfaces. There
is a danger of serious personal injury and damage to
property if the kit or components are improperly used or
installed incorrectly. The kit is not electrically isolated from
the AC/DC input. The evaluation board is directly linked to
the mains voltage. No insulation is ensured between the
accessible parts and the high voltage. All measuring
equipment must be isolated from the mains before powering
the board. When using an oscilloscope with the demo, it
must be isolated from the AC line. This prevents shock from
occurring as a result of touching any single point in the
circuit, but does NOT prevent shock when touching two or
more points in the circuit. Do not touch the evaluation board
after disconnection from the voltage supply; several parts
and power terminals, which contain energized capacitors,
must be allowed to discharge.
All operations involving transportation, installation and use, as well as maintenance, are to
be carried out by skilled technical personnel (national accident prevention rules must be
observed). For the purpose of these basic safety instructions, “skilled technical personnel”
are considered as suitably qualified people who are familiar with the installation, use, and
maintenance of power electronic systems.
1.3.2
Eevaluation board intended use
The STEVAL-IHM028V2 evaluation board is designed for evaluation purposes only and
must not be used in final applications. The technical data, as well as information concerning
the power supply conditions, must only be taken from the relevant documentation and must
be strictly observed.
1.3.3
Evaluation board installation
The installation and cooling of the evaluation board must be done in accordance with the
specifications and the targeted application.evaluation
•
The motor drive converters are protected against excessive strain. In particular, no
components are to be bent or isolating distances altered during the course of
transportation or handling.
•
No contact must be made with other electronic components and contacts.
•
The boards contain electrostatically sensitive components that are prone to damage
through improper use. Electrical components must not be mechanically damaged or
destroyed.
DocID18293 Rev 2
5/47
47
System introduction
1.3.4
UM1036
Electrical connections
Applicable national accident prevention rules must be followed when working on the main
power supply. The electrical installation must be carried out in accordance with the
appropriate requirements.
A system architecture which supplies power to the evaluation board must be equipped with
additional control and protective devices in accordance with the applicable safety
requirements (e. g. compliance with technical equipment and accident prevention rules).
6/47
DocID18293 Rev 2
UM1036
Board description
2
Board description
2.1
System architecture
A generic motor control system can be basically schematized as the arrangement of four
main blocks (see Figure 2).
•
Control block - its main task is to accept user commands and motor drive
configuration parameters. It provides all digital signals to implement the proper motor
driving strategy. The STM3210B-EVAL evaluation board, based on the STM32
microcontroller can be used as the control block, thanks to the motor control connector
equipped on the STEVAL-IHM028V2.
•
Power block - it is based on 3-phase inverter topology. The heart of the power block is
the STGIPS20C60 integrated intelligent power module which contains all the
necessary active components. Please refer to the STGIPS20C60 datasheet for more
information.
•
Motor - the STEVAL-IHM028V2 evaluation board is able to properly drive any PMSM,
but the FOC itself is mostly conceived for sinusoidal shaped back-EMF. The evaluation
board is also convenient for driving any 3-phase asynchronous motor.
•
Power supply block - able to work from 90 VAC to 285 VAC or from 125 VDC to 400
VDC. The power block is based on a buck converter with a VIPer26 controller. Please
refer to Section 3 to properly set the jumpers according to the required application.
Figure 2. Motor control system architecture
&RQWUROEORFN
02725
3RZHUVXSSO\
3RZHUEORFN
$0
Of the above motor control system architecture, the STEVAL-IHM028V2 includes the power
supply and the power block hardware blocks.
DocID18293 Rev 2
7/47
47
8/47
%XV
,1387
-
/
DocID18293 Rev 2
&
8
9,3HU/'
.%3&3
'
677+/$
6RXUFH 6RXUFH
&203
6RXUFH
6RXUFH
'UDLQ
'UDLQ 9'' 'UDLQ
'UDLQ
/,0
)% 5
%XFNFRQYHUWHU
&
Q);
) $
)86([
5H%
:
&
Q)
<
&
Q)<
&
&
1&
9OLQHDU
'
%=9&60'
&
&
5
5
&
Q)
&
&
Q)
8 /)$%'775
9,1 9287
*1'
&
Q)
5
5
5
'
677+/$
/ P+
&
Q)
5
' 1
9
'&BEXVBYROWDJH
9BGRXEOHU
'
$ %
5
'
/('UHG
&
5
&
Q)
'
%$7-),/0
9
&
Q)
&
Q)
9
$0
9
9''BPLFUR
%XVBYROWDJH
9''BPLFUR
&
& &
Q) Q)
%XV
: 9''
5
5
5
&
&
Q)
&
&
2.2
5H$
,QSXWSDUWZLWKEULGJH
Board description
UM1036
Board schematic
Figure 3. STEVAL- IHM028V2 schematic - part 1
DocID18293 Rev 2
-
3:0B95()
9
9''BPLFUR
%XV
SKDVHB&
SKDVHB%
SKDVHB$
3:0B95()
0BSKDVHB$
0BSKDVHB%
(0B6723
3:0$+
3:0$/
3:0%+
3:0%/
3:0&+
3:0&/
&XUUHQWB$
&XUUHQWB%
&XUUHQWB&
:
17&BE\SDVVBUHOD\
%
$
SKDVHB$
SKDVHB%
SKDVHB&
%(0)GDXJKWHUERDUG
6RIWZDUHEUDNH
2&3RII
02725
-
0RWRURXWSXW
17&BE\SDVVBUHOD\
0RWRUFRQQHFWRU
-
0RWRUFRQQHFWRU
5
5
&
Q)
0BSKDVHB&
:
%XVBYROWDJH
9
*1'
4
%&
'
1
5
5
)LQGHU
'
/('\HOORZ
/6
9''BPLFUR
&
Q)
&
Q)
5H%
5H$
$0
9
9
&
OLQHEDU
+HWBWHPSHUDWXUH
'
%$7-),/0
,QUXVKE\SDVV
9''BVXSSO\
&
Q)
9
,1 9287
8
/0$%
9OLQHDU
UM1036
Board description
Figure 4. STEVAL- IHM028V2 schematic - part 2
9/47
47
-
'
%=;%9
5
5
9
9''BPLFUR
(QFRGHUKDOO
+$
+%
+=
9
*1'
5
4
%&
5
9 %XV
4
%&
5
&
Q)
8
76%,/7
&
Q)
+DOO
5
$%
:
5
&
Q)
5
5
5
5
5
5
5
&
5
5
5
+$
&
4 S)
%&
&
S)
5
5
9
&
&
&
S) S) S)
:
%UDNHFRQWURO
5
5
& Q)
8
76,/7
9
4
%&
4
%&
4
%&
6RIWZDUHEUDNH
5
5
8)
0+&5
8(
0+&5
8'
0+&5
8&
0+&5 5
8%
0+&5
8$
0+&5
DocID18293 Rev 2
10/47
+DOOHQFRGHU
4
%&
4
%&
5
%UDNHFRQWURO
5
5
%$7-),/0
&
Q) '
5
1&
5
'
/('JUHHQ
5
7DFKRPHWHU
-
5
5
5
4
%&%
9 %XV
%$7-),/0
'
5
%UDNH
-
&
Q)
$0
4
67*:1%6'
5
4
%&
7DFKRPHWHU
0BSKDVHB$
&
Q)
:
&
Q) 5
1&
7DFKRPHWHUVHQVRU
9''BPLFUR
9''BPLFUR
0BSKDVHB&
0BSKDVHB%
0BSKDVHB$
&
Q)
Board description
UM1036
Figure 5. STEVAL- IHM028V2 schematic - part 3
DocID18293 Rev 2
EM_STOP
PWM-C-L
PWM-C-H
Phase C - input
PWM-B-L
PWM-B-H
Phase B - input
PWM-A-L
PWM-A-H
Phase A - input
R55
R54
R59
C57
330 pF
R76
R63
R65
R62
R61
R60
R58
R57
R56
R53
+15 V
C45
10 pF
VDD_micro
C54
C55
10 pF 10 pF
+3.3 V
C51 C52
10 pF 10 pF
+3.3 V
C44
10 pF
+3.3 V
OCP off
C50
C48
C46
!SD
D15
BAT48JFILM
C53
C49
C47
C56
2.2 nF
15 SD
16 CIN
R73
R64
STGIPS20C60
OUT U
VBOOT U
LIN U
HIN U
VCC
OUT V
VBOOT V
GND
LIN V
HIN 2
OUT W
VBOOT W
13 LIN W
14 HIN W
1
2
3
4
5
6
7
8
9
10
11
12
U7
IPM module
19
18
17
22
21
20
25
24
23
R72
+3.3 V
P3
W
E3
P2
V
E2
P1
U
E1
R66
phase_C
phase_B
phase_A
E3_GND
R74
R67 R68
E3
1_shunt
W9
3_shunt
W7
E2_GND
R75
R69 R70
E2
1_shunt
W8
E1
AM07423
E1_GND
R71
W10
3_shunt
+Bus
UM1036
Board description
Figure 6. STEVAL- IHM028V2 schematic - part 4
11/47
47
12/47
DocID18293 Rev 2
(B*1'
(
(B*1'
(
5
*DLQ
:
5
N:
5
5
5
5
5
9
5
5
*DLQ
:
:
*DLQ
&
S)
5
5
9
&
S)
5
5
&
S)
9
5
(B*1'
&
S)
&
Q)
*DLQ
:
5
& S)
5
8&
769
(
%$7-),/0 '
&XUUHQWVHQVLQJ%
& S)
8$
769
&XUUHQWVHQVLQJ$
5
5
9
%$7-),/0 '
5
&
5
5
&XUUHQWB$
9''BPLFUR
&XUUHQWB%
&
S)
9''BPLFUR
9
&
S)
5
9
5
5
5
%$7-),/0 '
5
$0
&
Q)
9
&XUUHQWB&
9''BPLFUR
8'
769 5
+HWBWHPSHUDWXUH
17&BWHPS
7HPSHUDWXUHDPSOLILHU
& S)
5
8%
769
5
&XUUHQWVHQVLQJ&
Board description
UM1036
Figure 7. STEVAL- IHM028V2 schematic - part 5
DocID18293 Rev 2
5HI
5
&
S)
5
76 8%
5 8
76%,/7
&
S)
5
5
+HWBWHPSHUDWXUH
5HI
5
5
5
5
5
)DQFRQWUROOHU
5
8$
76
2YHUKHWFRPSDUDWRU
&
Q)
73
73
73
73
73
73
73
73
73
73
73
73
)DQFRQWUROOHU
9
9
&
Q)
4
%&
)$1
'
1
)$1
+HWBWHPSHUDWXUH
6'
9
3:0$/
3:0$+
3:0%/
3:0%+
3:0&/
3:0&+
&XUUHQWB$
&XUUHQWB%
&XUUHQWB&
SKDVHB$
SKDVHB%
SKDVHB&
73
73
73
73
73
73
73
73
73
73
7HVWSLQV
&
Q)
W
5
57
5HI
$0
+HWBWHPSHUDWXUH
0BSKDVHB$
0BSKDVHB%
0BSKDVHB&
%XVBYROWDJH
%UDNHFRQWURO
9
9
17&BWHPS
9
+HDWVLQNWHPSHUDWXUH
UM1036
Board description
Figure 8. STEVAL- IHM028V2 schematic - part 6
13/47
47
Board description
UM1036
2.3
Circuit description
2.3.1
Power supply
The power supply for the STEVAL-IHM028V2 evaluation board is implemented as
a wide range converter. The range of the input voltage is from 90 VAC or 125 VDC up to 285
VAC or 400 VDC. This range allows the evaluation board to be used in direct connection
with various single phases as well as the PFC input stage.
If the input AC voltage does not surpass 145 VAC, it is possible to apply the input voltage
doubler, this is done by shorting the W15 jumper. This configuration almost doubles the
input AC voltage to a standard level and allows to evaluate the motor control application with
a low level of input AC voltage.
The auxiliary power supply for all active components on the evaluation board is
implemented as a buck converter based on U2 VIPer26L which works with a fixed frequency
of 60 kHz. The output voltage of the converter is +15 VDC. Voltage is fed into the intelligent
power module (IPM) as supply voltage, as well as into linear regulators LF33ABDT and
L78M05AB. Linear regulators provide +3.3 VDC and +5 VDC for supplying operational
amplifiers and further related parts placed on the evaluation board. The selection of supply
voltage for hardware peripherals placed on the board is done with jumper W1. In the “A”
position the supply voltage selected is +3.3 V and in the “B” position it is +5 V. Thanks to
jumper W3, it is possible to supply the connected MCU driving board with related supply
voltage. Maximal consumptive current of the MCU unit must not surpass 50 mA. Please
refer to the VIPer26LD datasheet for more information.
Information regarding the value of the supply bus voltage on the main filtering capacitors is
sensed with the voltage divider built around R2, R5, and R8 and is fed into the dedicated
control unit through the J2 connector. The proper voltage partitioning for applied resistor
values is 0.0075.
The presence of +15 VDC on the board is indicated with the D5 green LED “Power ON”.
Figure 9 describes the power supply section with a simplified block diagram.
Figure 9. Power supply block diagram
%869'&
9'&
9'&
'&%86
0$;9'&
,1387
/LQHDUUHJXODWRU
/0
0,1
0$;
9$& 9$&
9'& 9'&
9'&
%ULGJH
UHFWLILHU
%XFNFRQYHUWHU
9,3HU/'
/LQHDUUHJXODWRU
/)
:
9ROWDJH
GRXEOHU
$0
14/47
DocID18293 Rev 2
UM1036
2.3.2
Board description
Inrush limitation
The input stage of the evaluation board is provided with an NTC resistor to eliminate input
inrush current peak during the charging of the bulk capacitors. To achieve a higher efficiency
of the inverter it is possible to bypass the NTC after the start-up phase. The NTC bypass
signal is provided from the MCU board through the J2 connector. The yellow D10 LED diode
“Current limiter” is turned off when the inrush NTC is bypassed.
A basic EMI filter based on X2 and Y2 capacitors was implemented on the board. The EMI
filter is not able to absorb EMI distortion coming from the inverter for all ranges of the
applications. The final EMI filter must be designed according to the motor and the design of
the related EMI filter is up to the user according to the chosen motor and final target
application. The heatsink itself is connected to the earth pin in the J1 connector. It is
recommended to connect the heatsink to a negative voltage potential - common ground
when a DC voltage is used to supply the evaluation board.
2.3.3
Power block based on IGBT module
The IGBT module STGIPS20C60 consists of high, rugged IGBT power switches and three
smart drivers. STGIPS20C60 is provided with advanced gate smart drivers, many features
are available, such as integrated comparators for overcurrent or short-circuit protection, and
the “SMART SHUTDOWN” function. Please refer to the STGIPS20C60 datasheet for more
information.
2.3.4
Brake function
A hardware brake feature is implemented on the STEVAL-IHM028V2 evaluationevaluation
board. This feature connects the external resistive load, applied to the J7 connector, to the
main supply bus to eliminate overvoltage generated while the motor acts as a generator.
This connected load must be able to dissipate all motor generated energy. Almost any kind
of high power resistor which may be used as dissipative load also has relative high parasitic
inductance. Due to such inductance it is important to take care not to damage the brake Q8
IGBT switch with a freewheeling diode applied directly to the terminals of the dissipative
power resistor used.
Voltage on the bus is sensed through a voltage divider net, with resistors R40, R41, and
R48, and is compared to the precise voltage reference U5. The brake dummy load is
switched on when the voltage on the bus reaches approximately 435 VDC and is switched
off when the voltage falls bellows 415 VDC. This voltage level has been chosen to be fully
compliant with the possible use of front-end PFC stage. The brake function can also be
activated by the microcontroller through the J2 motor-control connector (PWM_Brake
signal). For this configuration, the user should set the W2 jumper to position “A”. The brake
threshold levels can be modified by calculating R49 and R51 new values. D13 red LED
diode “Brake” indicates the acting brake switch.
2.3.5
Overcurrent protection
Hardware overcurrent protection (OCP) is implemented on the board. This feature takes
advantage of STGIPS20C60 intelligent module where an internal comparator is
implemented. Thanks to the internal connection between the comparator output and
shutdown block of the IPM, the intervention time of overcurrent protection is extremely low,
ranging slightly above 200 ns. Please see Figure 10 for details.
DocID18293 Rev 2
15/47
47
Board description
UM1036
Overcurrent protection acts as soon as the voltage on the CIN pin rises above the internal
voltage reference (typical value VREF_INT is 0.53 V). Considering the default value of the
OCP shunt resistor, it follows that the maximum allowed current is equal to:
Equation 1
Ishunt
MAX
0.53 × ( R1 × R2 + R 2 × R3 + R1 × R3 ) – 3.3 × R1 × R2
= ----------------------------------------------------------------------------------------------------------------------------------------------R LS × R2 × R3
With the default values this gives:
Ishunt_MAX ~ 20 A
Figure 10. Overcurrent protection
9
5 5
8
6'
6PDUW6'
6PDUW6'
5 5
&203$5$725
&,1
9
5()
5 5
5/6
VHQVH
UHVLVWRU
67*,36.
*1'
$0
Overcurrent protection can be disabled if the W2 jumper is set to the “B” position. This may
be necessary and is often useful when the user decides to make the brake operate by
turning on the three low-side switches. In fact, if the motor acts as a generator, it is
necessary to protect the hardware, preventing the bus voltage from exceeding a safety
threshold. In addition to dissipating the motor energy on a brake resistor, it's possible to
short the motor phases, preventing the motor current from flowing through the bulk
capacitors. Please note that if the OCP is disabled, the evaluationevaluation board is not
protected against any overcurrent event.
16/47
DocID18293 Rev 2
UM1036
2.3.6
Board description
Current sensing amplifying network
The STEVAL-IHM028V2 motor control evaluation board can be configured to run in various
current reading configuration modes:
•
Three-shunt configuration - suitable for field oriented control (FOC)
•
Single-shunt configuration - suitable for FOC in a single-shunt configuration
•
Single-shunt - six-step configuration - suitable for scalar control.
Configuration with a shunt resistor, where voltage amplified with an operational amplifier is
sensed, was chosen as current sensing networks. Single-shunt configuration requires a
single op amp, three-shunt configuration requires three op amps. For compatibility
purposes, one of them is common to both basic configurations.
The configuration jumpers W11, W12, W13, and W14 allow to set the common op amp to
achieve compatibility between single-shunt six-step configuration (suitable for scalar
control) and three-shunt or single-shunt FOC current reading configuration. The operational
amplifier TSV994 used on amplifying networks has a 20 MHz gain bandwidth and operates
with just a single positive supply of +5 V.
Three-shunt FOC or single-shunt FOC current reading configuration
Details of the FOC current-sensing reading configuration are shown in Figure 11. In this
configuration, the alternating signal on the shunt resistor, with positive and negative values,
must be converted to be compatible with the single positive input of the microcontroller A-D
converter used to read the current value.
The op amp is used in symmetrical follower mode: its gain is set by resistors r and R:
Equation 2
( r1 + RLS ) × r2
r = --------------------------------------r1 + R LS + r2
R+r
G = -----------r
It is possible to calculate the voltage on the output of the op amp OP OUT - VOUT as a sum
of a bias VBIAS and a signal VSIGN component equal to:
Equation 3
V OUT = V SIGN + VBIAS
3.3
V BIAS = --------------------------------------------------------- × G
1
1
1
------- + -------- + -------- × R3
R1 R2 R3
I × RHS
V SIGN = --------------------------------------------------------- × G
1
1
1
-------- + ------- + -------- × R1
R1 R2 R3
Total gain of the circuit including the resistor divider is equal to:
DocID18293 Rev 2
17/47
47
Board description
UM1036
Equation 4
V SIGN
VSIGN
G TOT = ---------------- = ------------------V IN
R HS × I
With the default values this gives:
•
VBIAS = 1.57 V
•
Maximal voltage of VSIGN = 1.56 V
•
G = 5.38
•
GTOT = 3.90
•
Maximum current amplifiable without distortion is 16 A.
Figure 11. Configuration for FOC
9
5 555
9
23$03
23287
5555
23
23
5+6
VHQVH
UHVLVWRU
55
55
ó 769
5 /6
VHQVH
UHVLVWRU
U 555
U 555
5 555
*1'
$0
Table 1 shows the mentioned setting of gain jumpers for both FOC configurations.
Table 1. Gain settings for FOC current reading configuration
Setting for FOC configuration
Three-shunt configuration
Single-shunt configuration
W11
Present
W11
Present
W12
Present
W12
Present
W13
Present
W13
Present
W14
Present
W14
Present
Setting of gain
Six-step (block commutation) current reading configuration
In the case of six-step (also called block commutation) current control, only two of the motor
phases conduct current at the same time. Therefore, it is possible to use only one shunt
resistor placed on the DC link to measure the motor phase current. Furthermore, as the
current is always flowing in the same direction on the shunt resistor, only positive current
must be measured, and in this case the amplifying network needs to be properly designed.
The details of single-shunt current sensing reading configuration are shown in Figure 12. In
this configuration, the current sampling is done only when the value on the shunt resistor is
positive. Only the positive value read on the shunt resistor allows the setting of a higher gain
for the op amp than the one set in three-shunt reading mode.
18/47
DocID18293 Rev 2
UM1036
Board description
The op amp is used in follower mode with gain of the op amp set by resistors:
Equation 5
( r1 + RLS ) × r 2
r = --------------------------------------r1 + R LS + r2
R+r
G = -----------r
It is possible to calculate the voltage on the op amp output OP OUT - VOUT as the sum of
a bias VBIAS and a signal VSIGN component equal to:
Equation 6
V OUT = V SIGN + VBIAS
3.3
V BIAS = --------------------------------------------------------- × G
1
1
1
------- + -------- × R3
R1- + ------R2 R3
1 × R HS
V SIGN = --------------------------------------------------------- × G
1
1
1
------- + -------- + -------- × R1
R1 R2 R3
Total gain of the circuit with the resistor divider is equal to:
Equation 7
V SIGN
VSIGN
G TOT = ---------------- = ------------------V IN
R HS × I
With the default values this gives:
•
VBIAS = 0.38 V
•
Maximal voltage of VSIGN = 2.76 V
•
G = 8.02
•
GTOT = 6.90
•
Maximum current amplifiable without distortion is 16 A.
DocID18293 Rev 2
19/47
47
Board description
UM1036
Figure 12. Six-step current sensing configuration
9
5 55
9
23$03
23287
5 5
23
23
5+6
VHQVH
UHVLVWRU
5
55 ó 769
5 /6
VHQVH
UHVLVWRU
U 5
5 55
U 55
*1'
$0
Table 2 shows the mentioned setting of gain jumpers for this configuration.
Table 2. Gain settings for six-step current reading configuration
Setting for six-step configuration
Single-shunt configuration
W11
Not present
W12
Not present
W13
Not present
W14
Not present
Setting of gain
2.3.7
The tachometer and Hall/encoder inputs
Both the tachometer and Hall/encoder inputs have been implemented on the board. When
using a Hall or encoder sensor, the W5 jumper must be connected and the W4 jumper
disconnected. The W6 jumper set to position “A” allows to supply any connected Hall sensor
with the same supply voltage as other hardware peripherals (+3.3 VDC or
+5 VDC depending on the W1 jumper). Setting the W6 jumper to position “B” supplies the
Hall sensor directly with +5 VDC, which is the most common voltage for a Hall sensor. The
U4 Hex Schmitt inverter is used as the voltage level shifter for connected Hall sensors. If
using a tachometer, jumper W5 must be disconnected and jumper W4 connected.
This type of adjustable feature allows the testing and evaluating of motors with a wide
spectrum of various sensors.
2.3.8
Temperature feedback and overtemperature protection (OTP)
Hardware overtemperature protection is implemented on the STEVAL-IHM028V2 evaluation
board. This feature fully protects the IPM module against damage when the temperature on
the junction on the IPM surpasses a defined value. The temperature is sensed through an
NTC resistor RT1. The measured signal is amplified with an operational amplifier and then
fed through the J2 motor connector to the MCU control unit to be read with an A-D
converter. The signal is also fed to the U9A comparator where it is compared with a 2.5 V
reference voltage. The precision reference U10 TS3431 provides this 2.5 V reference
20/47
DocID18293 Rev 2
UM1036
Board description
voltage. The output signal of the comparator is fed into the IPM to stop the commutation of
the connected motor as well as into the MCU control unit through the J2 connector. With the
value of the used resistor networks and applied NTC resistor, the shutdown temperature of
the heatsink is somewhere between 85 °C and 90 °C.
2.3.9
Active heatsink cooling
For better thermal transfer of heat from the heatsink, active fan cooling is implemented on
the board. The aluminum profile used is type 8424 from PADA Engineering. The
temperature is sensed with the NTC resistor and compared with a reference voltage in
comparator U9B. The fan is switched on automatically when temperature of the heatsink
reaches approximately 40 °C and is switched off when temperature of the heatsink falls to
35 °C. The thermal resistance of the heatsink, when the fan is not activated, is visible in
Figure 13, the thermal resistance with active fan cooling is visible in Figure 14.
Figure 13. Thermal resistance of the heatsink
5 WK&:
5WKIRUUHODWHGGLVVLSDWHGSRZHU:
$0
DocID18293 Rev 2
21/47
47
Board description
UM1036
Figure 14. Thermal resistance of the heatsink with continuous fan cooling
5 WK &:
5WKIRUUHODWHGGLVVLSDWHGSRZHU:
$0
22/47
DocID18293 Rev 2
UM1036
3
Hardware setting of the STEVAL-IHM028V2
Hardware setting of the STEVAL-IHM028V2
The STEVAL-IHM028V2 evaluation board can be driven through the J2 motor connector by
various STMicroelectronics MCU control units which feature a unified 34-pin motor
connector. The evaluation board is suitable for field oriented control as well as for
tachometer or Hall sensor closed-loop control. The STEVAL-IHM028V2 evaluation board
ideally fits with the STM3210B-EVAL board based on the STM32 MCU family as the control
unit for FOC-driving algorithms.
3.1
Hardware settings for six-step (block commutation) current
control in single-shunt configuration
To drive any motor, the user must ensure that:
•
The motor control evaluation board is driven by a control board which provides the six
output signals required to drive the 3-phase power stage
•
The motor is connected to the J4 motor output connector
•
If using an encoder or Hall sensor connection, it is connected to connector J5
•
If using a tachometer connection, it is connected to connector J6
•
If using the brake control feature, connect a dissipative power load to connector J7.
Table 3 shows the jumper settings for any motors. Please confirm that the evaluation board
input voltage is in the range of 125 VDC to 400 VDC or 90 VAC to 285 VAC.
Table 3. Jumper settings for PMSM or generic AC motor - six-step
Jumper
Settings for six-step current control
A position for VDD = 3.3 V
W1
B position for VDD = 5 V
A position for software brake
W2
B position for disabling OCP
Not present
W3
Present - supply J2 with VDD (max. 50 mA)
Present for tachometer
W4
Not present for Hall / encoder
Present for Hall / encoder
W5
Not present for tachometer
W6
A position - VDD for Hall / encoder
B position - +5 V for Hall / encoder
W7
Present
W8
Present
W9
Not present
W10
Not present
DocID18293 Rev 2
23/47
47
Hardware setting of the STEVAL-IHM028V2
UM1036
Table 3. Jumper settings for PMSM or generic AC motor - six-step
Jumper
Settings for six-step current control (continued)
W11
Not present
W12
Not present
W13
Not present
W14
Not present
Present for voltage doubler (max. 145 VAC)
W15
Not present for normal supply range
3.2
Hardware settings for FOC in three-shunt configuration
To drive any motor, the user must ensure that:
•
The motor control evaluation board is driven by a control board which provides the six
output signals required to drive the 3-phase power stage
•
The motor is connected to the J4 motor output connector
•
If using an encoder or Hall sensor connection, it is connected to connector J5
•
If using a tachometer connection, it is connected to connector J6
•
If using the brake control feature, connect a dissipative power load to connector J7.
Table 4 shows the jumper settings for any motors. Please confirm that the evaluation board
input voltage is in the range of 125 VDC to 400 VDC or 90 VAC to 285 VAC.
Table 4. Jumper settings for PMSM or generic AC motor - FOC in three-shunt
Jumper
W1
Settings for FOC in three-shunt
A position for VDD = 3.3 V
B position for VDD = 5 V
A position for software brake
W2
B position for disabling OCP
Not present
W3
Present - supply J2 with VDD (max. 50 mA)
Present for tachometer
W4
Not present for tachometer / encoder
Present for Hall / encoder
W5
Not present for tachometer
W6
A position - VDD for Hall / encoder
B position - +5 V for Hall / encoder
24/47
W7
Not present
W8
Not present
W9
Present
W10
Present
DocID18293 Rev 2
UM1036
Hardware setting of the STEVAL-IHM028V2
Table 4. Jumper settings for PMSM or generic AC motor - FOC in three-shunt
Jumper
Settings for FOC in three-shunt
W11
Present
W12
Present
W13
Present
W14
Present
Present for voltage doubler (max. 145 VAC)
W15
Not present for normal supply range
3.3
Hardware settings for FOC in single-shunt configuration
To drive any motor, the user must ensure that:
•
The motor control evaluation board is driven by a control board which provides the six
output signals required to drive the 3-phase power stage
•
The motor is connected to the J4 motor output connector
•
If using an encoder or Hall sensor connection, it is connected to connector J5
•
If using a tachometer connection, it is connected to connector J6
•
If using the brake control feature, connect a dissipative power load to connector J7.
Table 5 shows the jumper settings for any motors. Please confirm that the evaluation board
input voltage is in the range of 125 VDC to 400 VDC or 90 VAC to 285 VAC.
Table 5.
Jumper settings for PMSM or generic AC motor - FOC in single-shunt
Jumper
W1
Settings for FOC in single-shunt
A position for VDD = 3.3 V
B position for VDD = 5 V
A position for software brake
W2
B position for disabling OCP
Not present
W3
Present - supply J2 with VDD (max. 50 mA)
Present for tachometer
W4
Not present for tachometer / encoder
Present for Hall / encoder
W5
Not present for tachometer
W6
A position - VDD for Hall / encoder
B position - +5 V for Hall / encoder
W7
Present
W8
Present
W9
Not present
W10
Not present
DocID18293 Rev 2
25/47
47
Hardware setting of the STEVAL-IHM028V2
Table 5.
UM1036
Jumper settings for PMSM or generic AC motor - FOC in single-shunt
Jumper
Settings for FOC in single-shunt
W11
Present
W12
Present
W13
Present
W14
Present
Present for voltage doubler (max. 145 VAC)
W15
Not present for normal supply range
26/47
DocID18293 Rev 2
UM1036
4
Testing of the evaluation board
Testing of the evaluation board
The overall test of the evaluation board was performed on a motor bench with two kinds of
applied PMAC motors. Test conditions are listed below.
Parameters for 1st test
Motor parameters:
•
Manufacturer: Reel S.r.l.
•
Type: IB100 F
•
Nominal power: 10.7 kW
•
4-pole pairs
•
Ls = 0.003465 H; Rs = 0.28 Ω
•
Ke = 84 V
•
Nominal speed: 3000 rpm
Test conditions:
•
Supply voltage 325 VAC; frequency 50 Hz
•
Testing output power 1.8 kW; testing speed 1000 rpm
•
Temperature of ambient 22 °C
•
Active fan cooling disabled; plastic covers removed
Parameters for 2nd test
Motor parameters:
•
Manufacturer: DOMEL
•
Type: 748.3.292
•
Nominal power: 1.6 kW
•
4-pole pairs
•
Ls = 0.045 H; Rs = 1.03 Ω
•
Ke = 84 V
•
Nominal speed: 2250 rpm
Test conditions:
•
Supply voltage 325 VAC; frequency 50 Hz
•
Testing output power 1.6 kW; testing speed 2250 rpm
•
Ambient temperature 22 °C
•
Active fan cooling disabled; plastic covers removed
The STM3210B board was used as the control unit with STM32 FOC firmware library v2.0
loaded. The flux weakening strategy with no sensors was chosen for testing. Three-shunt
resistors current sensing technique was selected. All related parameters of the motor were
included in the source code via the FOCGUI 2.0.0 application.
The duration of the tests was 45 minutes with the mentioned continuous output power
measured on the load of the motor testing stand. For correct thermal measurements of the
heatsink temperature, the assembled fan was removed together with the plastic covers.
Measured parameters, visible in Figure 15, were taken with the type IB100 F motor.
DocID18293 Rev 2
27/47
47
Testing of the evaluation board
UM1036
Figure 15. Current signals
1. Ch1 - Output phase current, current probe on phase C
Ch2 - voltage on TP19, phase current A
Ch3 - voltage on TP21, phase current B
Ch4 - voltage on TP22, phase current C.
28/47
DocID18293 Rev 2
UM1036
5
Description of jumpers, test pins, and connectors
Description of jumpers, test pins, and connectors
Table 6, 7, and 8 give a detailed description of the jumpers, test pins, and the pinout of the
connectors used.
Table 6.
Jumper description
Jumper
Selection
Description
A position
VDD = 3.3 V
B position
VDD = 5 V
A position
Software brake applied
B position
Disabling of OCP
Present
Supplying of MCU unit with VDD
Not present
MCU is supplied separately
Present
Tachometer connected
Not present
Hall or encoder connected
Present
Hall or encoder connected
Not present
Tachometer connected
A position
A position - VDD for Hall / encoder
B position
B position - +5 V for Hall / encoder
Present
Any single-shunt configuration
Not present
Any three-shunt configuration
Present
Any single-shunt configuration
Not present
Any three-shunt configuration
Present
Any three-shunt configuration
Not present
Any single-shunt configuration
Present
Any three-shunt configuration
Not present
Any single-shunt configuration
Present
Gain for any FOC
Not present
Gain for six-step control
Present
Gain for any FOC
Not present
Gain for six-step control
Present
Gain for any FOC
Not present
Gain for six-step control
Present
Gain for any FOC
Not present
Gain for six-step control
Present
Voltage doubler applied (max. 145 VAC)
Not present
Voltage doubler disabled
W1
W2
W3
W4
W5
W6
W7
W8
W9
W10
W11
W12
W13
W14
W15
DocID18293 Rev 2
29/47
47
Description of jumpers, test pins, and connectors
UM1036
Table 7. Connector pinout description
Name
Reference
Description / pinout
Supply connector
J1
1 - L - phase
2 - N- neutral
3 - PE- protected earth
4 - PE- protected earth
Motor control connector
J2
1 - emergency stop
2 - GND
3 - PWM-1H
4 - GND
5 - PWM-1L
6 - GND
7 - PWM-2H
8 - GND
9 - PWM-2L
10 - GND
11 - PWM-3H
12 - GND
13 - PWM-3L
14 - HV bus voltage
15 - current phase A
16 - GND
17 - current phase B
18 - GND
19 - current phase C
20 - GND
21 - NTC bypass relay
22 - GND
23 - dissipative brake PWM
24 - GND
25 - +V power
26 - heatsink temperature
27- PFC sync.
28 - VDD_m
29 - PWM VREF
30 - GND
31 - measure phase A
32 - GND
33 - measure phase B
34- measure phase C
BEMF daughterboard connector
J3
1 - phase A
2 - phase B
3 - phase C
4 - bus voltage
5 - 3.3 VDC
6 - VDD_micro
7 - GND
8 - PWM VREF
Motor connector
J4
30/47
A - phase A
B - phase B
C - phase C
DocID18293 Rev 2
UM1036
Description of jumpers, test pins, and connectors
Table 7. Connector pinout description (continued)
Name
Reference
Description / pinout
Hall sensors / encoder input connector
1 - Hall sensor input 1 / encoder A+
1 - Hall sensor input 2 / encoder B+
1 - Hall sensor input 3 / encoder Z+
4 - 5 VDC
5 - GND
J5
Tachometer input connector for AC motor speed loop control
J6
1 - tachometer bias
2 - tachometer input
Dissipative brake
J7
1 - open collector
2 - +bus voltage
Table 8. Testing pins description
Number
Description
TP1
Output phase A
TP2
Heatsink temperature
TP3
Output phase B
TP4
Sensed encoder / Hall signal H1/A+
TP5
Output phase C
TP6
Sensed encoder / Hall signal H2/B+
TP7
PWM - phase A - low-side
TP8
Sensed encoder / Hall signal H3/Z+
TP9
PWM - phase A - high-side
TP10
Voltage of the bus
TP11
PWM - phase B - low-side
TP12
Brake flag; when GND - brake switch activated
TP13
PWM - phase B - high-side
TP14
3.3 VDC
TP15
PWM - phase C - low-side
TP16
15 VDC
TP17
PWM - phase C - high-side
TP18
2.5 VDC - reference voltage
TP19
Current in phase A
TP20
GND
DocID18293 Rev 2
31/47
47
Description of jumpers, test pins, and connectors
UM1036
Table 8. Testing pins description
Number
32/47
Description
TP21
Current in phase B
TP22
Current in phase C
DocID18293 Rev 2
UM1036
6
Connector placement
Connector placement
A basic description of the placement of all connectors on the board is visible in Figure 16.
Figure 16. STEVAL-IHM028V2 connector placement
DocID18293 Rev 2
33/47
47
Bill of materials
7
UM1036
Bill of materials
A list of components used to build the evaluation board is shown in Table 9. The majority of
the active components used are available from STMicroelectronics.
Table 9. Bill of materials
Qty
Reference
Value / generic
part number
Package / class
Manufacturer
2
C1, C6
4.7 nF / Y2
Y2 safety CAP - 4n7
Murata
Manufacturing Co.,
Ltd.
4
C2, C3, C4, C75
1500 μF / 250 V
Elyt. 35 x 50
EPCOS
B43540E2158M000
1
C5
150 nF / X2
X2 cap; 6 x 15 x 26,5
EPCOS
B32923C3154K
2
C7, C72
10 nF
Capacitor, SMD 0805
Any
23
C8, C9, C11, C12, C14, C19,
C22, C23, C24, C25, C26,
C27, C29, C30, C34, C35,
100 nF
C36, C38, C41, C64, C66,
C70, C73
Capacitor, SMD 0805
Any
2
C10, C13
47 μF / 4 V
Elyt. capacitor, SMD 4*4
Any
2
C28, C65
22 μF / 6.3 V
Elyt. capacitor, SMD 4*4
Any
0
C15
N.C.
1
C16
220 nF
Capacitor, SMD 0805
Any
1
C17
3.3 μF / 450 V
Elyt. capacitor, 10x20
Any
1
C18
1 μF / 50 V
Elyt. capacitor, SMD 4*4
Any
1
C20
100 μF / 25 V
Elyt. capacitor, SMD 8*8
Any
2
C21, C40
4.7 μF / 35 V
Elyt. capacitor, SMD 4*4
Any
9
C31, C32, C33, C44, C45,
C51, C52, C54, C55
10 pF
Capacitor, SMD 0805
Any
2
C37, C56
2.2 nF
Capacitor, SMD 0805
Any
1
C39
470 pF
Capacitor, SMD 0805
Any
1
C42
4.7 nF
Capacitor, SMD 0805
Any
5
C43, C60, C63, C69, C74
100 pF
Capacitor, SMD 0805
Any
6
C46, C47, C48, C49, C50,
C53
1 μF
Capacitor, SMD 1206; 50 V
AVX
2
C57, C71
330 pF
Capacitor, SMD 0805
Any
6
C58, C59, C61, C62, C67,
C68
47 pF
Capacitor, SMD 0805
Any
1
RT1
10 kΩ
NTC, 10 kΩ, handle under screw
EPCOS B57703M
103G 40
34/47
DocID18293 Rev 2
UM1036
Bill of materials
Table 9. Bill of materials (continued)
Qty
Reference
Value / generic
part number
Package / class
Manufacturer
3
R1, R4, R7
100 kΩ
Resistor, SMD 1206
Any
3
R53, R57, R61
100 kΩ
Resistor, SMD 0805, 1%
Any
4
R2, R5, R40, R41
470 kΩ
Resistor, SMD 1206
Any
1
R3
10 Ω
NTC resistor 10R, through hole
EPCOS
B57464S0100M
2
R6, R10
120 Ω
Resistor, SMD 0805, 1%
Any
2
R8, R111
7.5 kΩ
Resistor, SMD 0805, 1%
Any
3
R9, R91, R106
51 kΩ
Resistor, SMD 0805, 1%
Any
1
R11
13 kΩ
Resistor, SMD 0805, 1%
Any
4
R12, R16, R31, R37
5.6 kΩ
Resistor, SMD 0805, 1%
Any
1
R13
160 Ω
Resistor, SMD 1206
Any
20
R14, R36, R44, R79, R86,
R95, R103, R54, R55, R58,
R59, R62, R63, R72, R78,
R80, R85, R87, R94, R97
1 KΩ
Resistor, SMD 0805, 1%
Any
7
R15, R27, R28, R29, R50,
R76, R93
10 kΩ
Resistor, SMD 0805, 1%
Any
9
R17, R18, R19, R20, R21,
R22, R23, R24, R25
4.7 kΩ
Resistor, SMD 0805, 1%
Any
0
R26, R43
N.C.
1
R30
100 Ω
Resistor, SMD 0805, 1%
Any
8
R32, R98, R77, R83, R84,
R90, R92, R100
8.2 kΩ
Resistor, SMD 0805, 1%
Any
4
R33, R49, R51, R114
15 kΩ
Resistor, SMD 0805, 1%
Any
1
R34
6.8 kΩ
Resistor, SMD 0805, 1%
Any
2
R35, R109
910 Ω
Resistor, SMD 0805, 1%
Any
2
R47, R96
220 Ω
Resistor, SMD 0805, 1%
Any
1
R38
22 Ω
Resistor, SMD 0805, 1%
Any
1
R39
68 kΩ
Resistor, SMD 0805, 1%
Any
1
R42
560 Ω
Resistor, SMD 0805, 1%
Any
4
R45, R108, R110, R117
2.2 kΩ
Resistor, SMD 0805, 1%
Any
1
R115
4.3 kΩ
Resistor, SMD 0805, 1%
Any
1
R46
220 kΩ
Resistor, SMD 0805, 1%
Any
2
R48, R52
27 kΩ
Resistor, SMD 0805, 1%
Any
5
R56, R60, R65, R116, R73
3.3 kΩ
Resistor, SMD 0805, 1%
Any
1
R64
16 kΩ
Resistor, SMD 0805, 1%
Any
Any
DocID18293 Rev 2
35/47
47
Bill of materials
UM1036
Table 9. Bill of materials (continued)
Qty
Reference
Value / generic
part number
Package / class
Manufacturer
8
R66, R67, R68, R69, R70,
R71, R74, R75
0.05 Ω
Resistor, SMD 2512, 1%, 2 W
Welwyn
6
R81, R82, R88, R89, R99,
R101
3.9 kΩ
Resistor, SMD 0805, 1%
Any
2
R102, R105
3 kΩ
Resistor, SMD 0805, 1%
Any
1
R104
2.7 kΩ
Resistor, SMD 0805, 1%
Any
1
R107
180 Ω
Resistor, SMD 0805, 1%
Any
1
R112
1.2 kΩ
Resistor, SMD 0805, 1%
Any
1
R113
120 kΩ
Resistor, SMD 0805, 1%
Any
1
R118
1.8 kΩ
Resistor, SMD 0805, 1%
Any
1
D1
GBPC3510W
Diode bridge 28.5 x 28.5 x 7.5;
wire legs, 35 A
Any
8
D2, D8, D11, D12, D15, D16,
BAT48JFILM
D17, D18
Diode SMD
STM
3
D3, D9, D19
1N4148
Diode SMD, MINI-MELF
Any
2
D4, D6
STTH1L06A
Diode SMD, SMA
STM
1
D13
LED Red
LED 3 mm, 2 mA, universal
Any
1
D7
BZV55C18SMD
Zener diode 18 V, MINI-MELF
Any
1
D10
LED yellow
LED 3 mm, 2 mA, universal
Any
1
D5
LED green
LED 3 mm, 2 mA, universal
Any
1
D14
BZX84B13V
Zener diode, SOT23, 13 V; 2%
Any
10
Q1, Q2, Q3, Q4, Q5, Q7, Q9,
BC847A
Q10, Q11, Q12
NPN transistor, SOT23
Any
1
Q6
BC857B
PNP transistor, SOT23
Any
1
Q8
STGW35NB60SD TO-247
1
Q13
BC807-25 SMD
PNP transistor 45 V / 0,5 A,
SOT23
FAIRCHILD
1
L1
330 μH
Inductive choke RM 5 mm
Coilcraft
1
L2
1.5 mH
SMD choke, 1.5 mH / 1.5 A
Coilcraft
1
U1
LF33ABDT-TR
Linear regulator DPAK
STM
1
U2
VIPer26LD
PWM smart driver, SO-16
STM
1
U3
L78M05AB
Linear regulator DPAK
STM
1
U4
M74HC14R
CMOS logic, SO-14
STM
2
U5, U10
TS3431BILT
Voltage reference, SOT23
STM
1
U6
TS391ILT
Op amp, SOT23-5
STM
1
U7
STGIPS20C60
IPM IGBT module
STM
36/47
DocID18293 Rev 2
STM
UM1036
Bill of materials
Table 9. Bill of materials (continued)
Qty
Reference
Value / generic
part number
Package / class
Manufacturer
1
U8
TSV994IDT
Op amp, SO-14
STM
1
U9
TS372ID
Dual comparator, SO-8
STM
0
TP1, TP3, TP5
N.C.
19
TP2, TP4, TP6, TP7, TP8,
TP9, TP10, TP11, TP12,
TP13, TP14, TP15, TP16,
TP17, TP18, TP19, TP20,
TP21, TP22
PCB terminal 1
mm
Test pin
W1
Jumper 2.54
Three pins of pin header +
jumper in position A
W2
Jumper 2.54
Three pins of pin header +
jumper in position A
W3
Jumper 2.54
Two pins of pin header
W4
Jumper 2.54
Two pins of pin header
W5
Jumper 2.54
Two pins of pin header + jumper
W6
Jumper 2.54
Three pins of pin header +
jumper in position A
W7
Jumper 2.54
N.C.
W8
Jumper 2.54
N.C.
W9
Jumper 2.54
Soldered PCB pads together
W10
Jumper 2.54
Soldered PCB pads together
W11
Jumper 2.54
Two pins of pin header + jumper
W12
Jumper 2.54
Two pins of pin header + jumper
W13
Jumper 2.54
Two pins of pin header + jumper
W14
Jumper 2.54
Two pins of pin header + jumper
W15
Jumper 2.54
N.C.
1+1
J1
Connector 4P
Connector RM 5 mm, 4-pole
male and female
Hartman
1
J2
MLW34G
MLW connector 34-pins
ARK
1
J3
BL815G
Pins RM 2.54 mm, (12-pins from
15-pin list)
1+1
J4
Connector 3P
Connector RM5 mm, 3-pole
male and female
1+1
J5
Con. 5 mm, 2P +
3P
Connector RM 5 mm, 2-pole and
ARK
3-pole, screw
1
J6
Con. 5 mm, 2P
Connector RM 5 mm, 2-pole,
screw
ARK
1
J7
Con. 5 mm, 2P
Connector RM 5 mm, 2-pole,
screw
ARK
DocID18293 Rev 2
Hartman
37/47
47
Bill of materials
UM1036
Table 9. Bill of materials (continued)
Qty
Reference
Value / generic
part number
Package / class
Manufacturer
1
LS1
Finder 4061
Relay 12 V; 16 A / 250 VAC
1
FAN1
Connector 2.54 /
3P
PSH02-03PG
2
F1
PA-PZ1008
Fuse holder 10 x 38; 2 pc in one
board
Fuse 16 A, high
cur.
P = 16 A / 120 kA - 500 V;
10 x 38
Heatsink
150 mm of AL profile 8424
(65 x 70)
PADA Engineering
AIREN red wings
70
Fan 12 V; 70 mm x 70 mm
x 15 mm
Airen
1
150
mm
1
38/47
Heatsink
DocID18293 Rev 2
Finder
UM1036
8
PCB layout
PCB layout
For this application a standard, double-layer, coppered PCB with a ~60 μm copper thickness
was selected. The PCB material is FR-4.
The dimensions of the board are:
•
Length: 195 mm
•
Width: 175 mm
•
PCB thickness: 1.55 mm
Figure 17. Copper tracks - top side
DocID18293 Rev 2
39/47
47
PCB layout
UM1036
Figure 18. Copper tracks - bottom side
40/47
DocID18293 Rev 2
UM1036
PCB layout
Figure 19. Silk screen - top side
DocID18293 Rev 2
41/47
47
PCB layout
UM1036
Figure 20. Silk screen - bottom side
42/47
DocID18293 Rev 2
UM1036
9
Ordering information
Ordering information
The evaluation board is available through the standard ordering system, the ordering code
is: STEVAL-IHM028V2. The items delivered include the assembled application board, board
documentation, PCB fabrication data, such as gerber files, assembly files (pick and place),
and component documentation.
10
Using STEVAL-IHM028V2 with STM32 FOC firmware
library
STM32 FOC firmware library (UM1052) is a firmware library which allows performing of the
FOC of a PMSM in configuration with and without sensors.
10.1
Environmental considerations
Warning:
The STEVAL-IHM028V2 evaluation board must only be used
in a power laboratory. The voltage used in the drive system
presents a shock hazard.
The kit is not electrically isolated from the DC input. This topology is very common in motor
drives. The microprocessor is grounded by the integrated ground of the DC bus. The
microprocessor and associated circuitry are hot and MUST be isolated from user controls
and communication interfaces.
Warning:
All measuring equipment must be isolated from the main
power supply before powering up the motor drive. To use an
oscilloscope with the kit, it is safer to isolate the DC supply
AND the oscilloscope. This prevents a shock occurring as
a result of touching any SINGLE point in the circuit, but does
NOT prevent shock when touching two or more points in the
circuit.
An isolated AC power supply can be constructed using an isolation transformer and
a variable transformer. A schematic of this AC power supply can be found in the AN438
application note. (Although this application note was written for a TRIAC, the isolation
constraints still apply for switching semiconductor devices such as IGBT or MOSFET).
Note:
Isolating the application rather than the oscilloscope is highly recommended in any case.
DocID18293 Rev 2
43/47
47
Using STEVAL-IHM028V2 with STM32 FOC firmware library
10.2
UM1036
Hardware requirements
To run the STEVAL-IHM028V2 together with the STM32 FOC firmware library, the following
is required:
10.3
•
The board: STEVAL-IHM028V2
•
High voltage insulated AC power supply up to 230 VAC
•
J-Link programmer - ST Link (not included in the package)
•
J-Link insulating board (not included in the package)
•
3-phase brushless motor with permanent magnet rotor (not included in the package)
•
Insulated oscilloscope (as required)
•
Insulated multimeter (as required).
Software modifications
The most convenient way to edit the parameters header file is through the use of the ST MC
Workbench (PC GUI configuration tool for the STM32 PMSM FOC SDK motor control
firmware library.
44/47
DocID18293 Rev 2
UM1036
11
Conclusion
Conclusion
This document describes the 2 kW 3-phase motor control STEVAL-IHM028V2 evaluation
board based on IPM as a universal fully-evaluated and adaptable motor control platform.
12
References
1.
STGIPS20C60 datasheet
2.
VIPer26 datasheet
3.
STGW35NB60SD datasheet
4.
UM0379 user manual
5.
UM0580 user manual
6.
UM0723 user manual
7.
UM0900 user manual
DocID18293 Rev 2
45/47
47
Revision history
13
UM1036
Revision history
Table 10. Document revision history
46/47
Date
Revision
Changes
13-Jan-2011
1
Initial release.
13-Nov-2014
2
Add new reference product.
DocID18293 Rev 2
UM1036
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2014 STMicroelectronics – All rights reserved
DocID18293 Rev 2
47/47
47