AND9034/D
Use of an Averaged
Behavior Model of NCP6334
in Pspice Simulation
Prepared by: Gang Chen
ON Semiconductor
http://onsemi.com
APPLICATION NOTE
Overview
the NCP6334B and the NCP6334C is the function of pin 6.
The pin 6 of the NCP6334B is an output of power good
signal, while the pin 6 of the NCP6334C is an input of mode
selection.
To provide very fast simulation results and initial design
of system parameters before a real board design in
applications, an averaged behavior model (ABM) of the
NCP6334 in Pspice has been developed to simulate transient
response and loop stability. Figure 1 shows a typical
simulation circuit with the NCP6334 averaged behavior
model in Pspice. The model is based on the NCP6334B, but
it is still valid for a simulation of the NCP6334C close−loop
behavior. This application note is to illustrate a simulation
procedure with the NCP6334 ABM in Pspice.
The NCP6334B/C, a family of synchronous buck
converters, which is optimized to supply the different sub
systems of portable applications powered by one cell Li−ion
or three cell Alkaline/NiCd/NiMH batteries. The devices are
able to deliver up to 2 A on an external adjustable voltage or
a fixed output voltage range from 0.6 V to 3.3 V upon
request. Operation with 3 MHz switching frequency allows
employing small size inductor and capacitors. Input supply
voltage feedforward control is employed to deal with wide
input voltage range. Synchronous rectification and
automatic PWM/PFM power save mode offer improved
system efficiency. The NCP6334B/C is in a 2.0 x 2.0 x
0.75 mm WDFN−8 package. The only difference between
C3
PARAMETERS:
Cfb = 15pF
Vout_FB
{Cfb}
R1
220k
U1
EN
MODE/PG
R5
1000k
R6
1000k
AVIN
PVIN
V3
5
6
7
8
EN
FB
MODE/PG
AGND
AVIN
SW
PVIN
PGND
4
0
SW
L
1
1uH
1
NCP6334
5Vdc
10mVac
0Vdc
110k
3
2
V2
R2
2
Rdcr
30m
Vout
Resr
4m
C1
10uF
Load
T1 = 0
T2 = 1.5e−4
T3 = 1.501e−4
T4 = 2.0e−4
T5 = 2.001e−4
T6 = 3.0e−4
I1 = 0.5
I2 = 0.5
I3 = 1.5
I4 = 1.5
I5 = 0.5
I6 = 0.5
0
Figure 1. Typical Simulation Circuit with NCP6334 Averaged Behavior Model
© Semiconductor Components Industries, LLC, 2011
August, 2011 − Rev. 0
1
Publication Order Number:
AND9034/D
AND9034/D
DETAILED DESCRIPTION
Download Pspice Model
Users can download the Pspice averaged behavior model of the NCP6334 from ON Semiconductor website, which is a
zipped file “NCP6334_ABM.ZIP” including one Pspice model lib file “NCP6334_ABM.LIB”, one schematic symbol olb file
“NCP6334_ABM.OLB”, and one design dsn file “NCP6334_ABM.DSN”. Save all the extracted files in a folder.
Model Installation
Create New Project
Users need to run ORCAD Capture or Allegro Design Entry CIS first, and then create a new blank project in Capture as shown
in Figure 2.
Figure 2. Create New Blank Simulation Project
Import Design File
Add the design file “NCP6334_ABM.DSN” into the Design Resources to replace the blank design.
Figure 3. Import Design File into Design Resources
Import Symbol File
Add the symbol file “NCP6334_ABM.OLB” into the Design Resources as shown in Figure 4.
http://onsemi.com
2
AND9034/D
Figure 4. Import Symbol File into Design Resources
Open Schematic
Open the schematic “Page 1” in the “Schematic1” under the design file as shown in Figure 5. Users can edit the schematic
according to real applications.
Figure 5. Open Schematic in Design File
Create Simulation Profile and Run Simulations
In order to run a new simulation, a simulation profile has to be created. In the simulation setting of the simulation profile,
users need to use browser to add the Pspice lib file “NCP6334_ABM.LIB” into the design library of the simulation
configuration files, as shown in Figure 7. The Pspice model of the NCP6334_ABM is able to support both time domain
transient simulation and AC frequency domain simulation. Users can set both configurations in the simulation profile.
http://onsemi.com
3
AND9034/D
Figure 6. Create a New Simulation Profile
Figure 7. Add Pspice lib File into the Library of the Configuration Files.
Time Domain Transient Simulation
Figure 8 shows a typical schematic for a time domain transient simulation. An AC source “V 2” is set to 0 V for its AC and
DC components. Users can edit parameters of the pulse current source “Load” to simulate load transient in the output Vout. In
order to reduce simulation time, a 100 ms internal soft start has been implemented in the model. A typical time−domain
simulation profile setting is shown in Figure 9. Users can review simulation waveforms in Pspice A/D after running a
simulation. Figure 10 shows an example of the simulation results regarding to a load transient event.
C3
PARAMETERS:
Cfb = 15pF
Vout_FB
{Cfb}
R1
220k
U1
EN
R5
1000k
MODE/PG
6
AVIN
7
R6
1000k
PVIN
V3
5Vdc
5
8
EN
FB
MODE/PG
AGND
AVIN
SW
PVIN
PGND
4
0mVac
0Vdc
110k
3
2
V2
R2
0
SW
L
1
2
1uH
1
NCP6334
Rdcr
30m
Vout
Resr
4m
C1
10uF
0
Figure 8. Typical Schematic for Time Domain Transient Simulation
http://onsemi.com
4
Load
T1 = 0
T2 = 1.5e−4
T3 = 1.501e−4
T4 = 2.0e−4
T5 = 2.001e−4
T6 = 3.0e−4
I1 = 0.5
I2 = 0.5
I3 = 1.5
I4 = 1.5
I5 = 0.5
I6 = 0.5
AND9034/D
Figure 9. Simulation Setting for Time Domain Simulation
Figure 10. Typical Simulation Results of Time Domain Simulation
Due to a benefit from the averaged behavior model, the total simulation time is just a few seconds and thus it is good for users
to optimize the system by running a parameter sweep simulation. Before running a parameter sweep simulation, at least one
“PARAM” part from the “SPECIAL.OLB” needs to be added in the schematic. As shown in the example schematic in Figure 8,
users can run parameter sweep for the capacitor C3 in the compensation network. Users can program a pattern of the parameter
sweep in the simulation profile as shown in Figure 11. Figure 12 shows multiple simulation results after the parameter sweep
simulation. It is very easy for users to see parameter impact on transient response.
http://onsemi.com
5
AND9034/D
Figure 11. Simulation Setting for Parametric Sweep in Time Domain Simulation
Cfb = 7 pF
Cfb = 15 pF
Cfb = 30 pF
Cfb = 30 pF
Cfb = 7 pF
Cfb = 15 pF
Figure 12. Typical Simulation Results of Parametric Sweep in Time Domain Simulation
AC Frequency Domain Simulation
With the NCP6334 averaged behavior model, users are able to use almost the same schematic to do AC frequency domain
simulation as what is used in the time domain simulation. The main difference is in the setting of the AC voltage source “V2”
shown in Figure 13. In the frequency domain simulation, usually a small AC voltage such as 1 0 mV ~ 100 mV is used.
http://onsemi.com
6
AND9034/D
C3
PARAMETERS:
Cfb = 15pF
Vout_FB
{Cfb}
R1
220k
U1
EN
MODE/PG
R5
1000k
R6
1000k
AVIN
PVIN
V3
5Vdc
5
6
7
8
EN
FB
MODE/PG
AGND
AVIN
SW
PVIN
PGND
4
10mVac
0Vdc
110k
3
2
V2
R2
0
SW
L
1
2
1uH
1
NCP6334
Rdcr
30m
Vout
Resr
4m
C1
10uF
Load
T1 = 0
T2 = 1.5e−4
T3 = 1.501e−4
T4 = 2.0e−4
T5 = 2.001e−4
T6 = 3.0e−4
I1 = 0.5
I2 = 0.5
I3 = 1.5
I4 = 1.5
I5 = 0.5
I6 = 0.5
0
Figure 13. Typical Schematic for AC Frequency Domain Transient Simulation
Figure 14 shows a simulation setting for an AC frequency domain simulation and Figure 15 shows typical simulation results.
Users can read close−loop bandwidth and phase margin from the bode plot.
Figure 14. Simulation Setting for AC Frequency Domain Simulation
http://onsemi.com
7
AND9034/D
Figure 15. Typical Simulation Results of AC Frequency Domain Simulation
Users also can run parametric sweep in an AC frequency domain simulation. Figure 16 shows a corresponding simulation
setting, and Figure 17 shows typical simulation results. Users can see parameter impact on close−loop stability.
Figure 16. Simulation Setting for Parametric Sweep in AC Frequency Domain Simulation
http://onsemi.com
8
AND9034/D
Cfb = 30 pF
Cfb = 15 pF
Cfb = 7 pF
Cfb = 30 pF
Cfb = 15 pF
Cfb = 7 pF
Figure 17. Typical Simulation Results of Parametric Sweep in AC Frequency Domain Simulation
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
AND9034/D