PCS3P6100A Spread Spectrum EMI reduction IC for HD Display frequencies. The device addresses the need of a low EMI clock generator for use in display systems covering wide choice of pixel frequencies. Features • Custom Clock Generator for Display Systems • Wide Operating Frequency Range covering most of the pixel frequencies PCS3P6100A reduces electromagnetic interference (EMI) at the clock source, allowing system wide reduction of EMI of all clock dependent signals. PCS3P6100A allows significant system cost savings by reducing the number of circuit board layers, ferrite beads, and shielding that are traditionally required to pass EMI regulations. • Generates a low EMI 1x Output • 4 Spread Deviation selection options • Supply voltage : 3.3V ± 0.3V 2.5V ± 0.125V • Frequency range: 3.3V: 20MHz – 130MHz 2.5V: 30MHz – 130MHz The Supply Voltage of the Device is 3.3V / 2.5V. It has two Spread Selection Pins, SS1% and SS2%. Refer to the Spread Deviation Selection Table for details. The Device is available in 6L-TSOT23 Package. • ModRate: 85KHz @ 72MHz • 6L-TSOT23 (6L-TSOT26) package Product Description PCS3P6100A is a versatile spread spectrum modulator designed specifically for a wide range of clock Application PCS3P6100A is targeted for use in Display Systems. Block Diagram VDD SS1% PLL CLKIN SS2% ModOUT VSS ©2010 SCILLC. All rights reserved. NOVEMBER 2010 – Rev. 1.1 Publication Order Number: PCS3P6100/D PCS3P6100A Pin Configuration (6L-TSOT23 Package) CLKIN 1 VSS 2 ModOUT PCS3P6100A 3 6 VDD 5 SS2% 4 SS1% Pin Description Pin# Pin Name Type Description 1 CLKIN I External Reference Input frequency. 2 VSS P Ground to entire chip. 3 ModOUT O Modulated Frequency Output. 4 SS1% I 5 SS2% I 6 VDD P Spread Deviation Selection Pin -1. Refer to Spread Deviation Selection Table for details. Has an Internal pull-up resistor. Spread Deviation Selection Pin -2. Refer to Spread Deviation Selection Table for details. Has an Internal pull-up resistor. Power to entire chip. Spread Deviation Selection Table SS2% Pin SS1% Pin Spread Deviation @ 66MHz L L ± 1.50% L H ± 1.25% H L ± 0.75% H H ± 1.00% ModRate Table 20MHz – 40MHz 40 MHz – 130 MHz Fin / 336 Fin / 840 ModRate Rev. 1 | Page 2 of 8 | www.onsemi.com PCS3P6100A Absolute Maximum Ratings Symbol VDD, VIN TSTG Parameter Rating Unit Voltage on any pin with respect to Ground -0.5 to +4.6 V Storage temperature -65 to +125 °C Ts Max. Soldering Temperature (10 sec) 260 °C TJ Junction Temperature 150 °C 2 KV TDV Static Discharge Voltage (As per JEDEC STD22- A114-B) Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect device reliability. Operating Conditions for 2.5V and 3.3V Supply Voltage Parameter VDD(2.5) VDD(3.3) Description Supply Voltage TA Operating Temperature (Ambient Temperature) CL Load Capacitance DC Electrical Characteristics for 2.5V Supply Symbol Parameter Min Min Max 2.375 2.625 3.0 3.6 -40 +85 °C 15 pF Typ Unit V Max Unit VIL Input low voltage VSS-0.3 0.7 V VIH Input high voltage 1.7 VDD+0.3 V IIL Input low current -35 µA IIH µA Input high current 35 VOL Output low voltage (VDD = 2.5V, IOL = 8mA) 0.6 VOH Output high voltage (VDD = 2.5V, IOH = -8mA) IDD Static supply current ICC Dynamic supply current (2.5V and no load) VDD Operating voltage tON Power-up time (first locked cycle after power-up) CIN Input Capacitance 5 pF ZOUT Output Impedance 40 Ω 1.8 1 4 11 2.375 Note: 1.CLKIN pin is pulled low. Rev. 1 | Page 3 of 8 | www.onsemi.com V V 2.5 mA mA 2.625 V 5 mS PCS3P6100A AC Electrical Characteristics for 2.5V Supply Symbol CLKIN ModOUT 1 tLH tHL 1 Parameter Min Typ Max Unit Input frequency 30 130 MHz Output frequency 30 130 MHz Output rise time (measured from 0.7V to 1.7V) 2.2 nS Output fall time (measured from 1.7V to 0.7V) 1.2 nS ±250 pS tJC Jitter (Cycle-to-cycle) tD Output duty cycle 40 50 60 % Note: 1. tLH and tHL are measured into a capacitive load of 15pF. DC Electrical Characteristics for 3.3V Supply Symbol Parameter Min Typ Max Unit VIL Input low voltage VSS-0.3 0.8 V VIH Input high voltage 2.0 VDD+0.3 V IIL Input low current -35 µA IIH Input high current 35 µA VOL Output low voltage (VDD = 3.3V, IOL = 8mA) 0.4 V VOH Output high voltage (VDD = 3.3V, IOH = -8mA) IDD Static supply current 4.5 mA ICC Dynamic supply current (3.3V and no load) VDD Operating voltage tON Power-up time (first locked cycle after power-up) CIN Input Capacitance 5 pF ZOUT Output Impedance 40 Ω 2.5 V 1 14 3.0 mA 3.3 3.6 V 5 mS Note: 1. CLKIN pin is pulled low. AC Electrical Characteristics for 3.3V Supply Symbol CLKIN ModOUT 1 tLH tHL 1 Parameter Min Typ Max Unit Input frequency 20 130 MHz Output frequency 20 130 MHz Output rise time (measured from 0.8 to 2.0V) 1.5 nS Output fall time (measured at 2.0V to 0.8V) 1.1 nS ±225 pS tJC Jitter (Cycle-to-cycle) tD Output duty cycle 45 Note: 1. tLH and tHL are measured into a capacitive load of 15pF. Rev. 1 | Page 4 of 8 | www.onsemi.com 50 55 % PCS3P6100A Deviation Charts Deviation vs Output frequency (35MHz to 130 MHz) at 25C for VDD = 2.5V 2.80% 2.50% Dev (%) 2.00% 1.50% 1.00% 0.50% 0.00% 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 Output (MHz) Figure-1 Deviation vs Output frequency (20MHz to 29 MHz) at 25C for VDD = 3.3V 2.50% 2.00% Dev (%) 1.50% 1.00% 0.50% 0.00% 20 21 22 23 24 25 26 27 28 29 Output (MHz) Figure-2 Deviation vs Output frequency (40MHz to 130 MHz) at 25C for VDD = 3.3V 2.50% 2.00% Dev(%) 1.50% 1.00% 0.50% 0.00% 40 Figure-3 45 50 55 60 65 70 75 80 85 90 95 100 105 Output (MHz) Note: Transition band is 30MHz to 34 MHz for VDD = 2.5V at 25C. Deviation in this band is 2.64% ± 3%. Transition band is 30MHz to 39 MHz for VDD = 3.3V at 25C. Deviation in this band is 1.67% ± 45%. Rev. 1 | Page 5 of 8 | www.onsemi.com 110 115 120 125 130 PCS3P6100A Deviation vs Output frequency (35 MHz to 130 MHz) across temperature for VDD 2.5V ± 5% 3.00% 2.50% Dev(%) 2.00% 1.50% 1.00% 0.50% 0.00% 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 Output (MHz) Deviation vs Output frequency (20 MHz to 29 MHz) across temperature for VDD 3.3V ± 0.3V 2.50% 2.7V(-40C) 2.7V(-40C) 2.5V(25C) 2.00% 1.50% Dev(%) 2.37V(85C) 1.00% 0.50% 0.00% 20 21 22 23 24 25 26 27 28 29 Output(MHz) Figure-5 Deviation vs Output frequency (40MHz to 130 MHz) across temperature for VDD = 3.3V ± 0.3V 3.00% 2.50% 3.6V(-40C) 2.00% Dev(%) 3.3V(25C) 3.0V(85C) 1.50% 1.00% 0.50% 0.00% 40 Figure-6 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 Output(MHz) Note: Transition band is 30MHz to 34 MHz for VDD = 2.5V ± 5%, across -40C to +85C. Deviation in this band is 1.8% ± 53%. Transition band is 30MHz to 39 MHz for VDD = 3.3V ± 0.3V, across -40C to +85C. Deviation in this band is 1.67% ± 60%. Rev. 1 | Page 6 of 8 | www.onsemi.com 130 PCS3P6100A Package Information 6L-TSOT23 Symbol A Dimensions Inches Millimeters Min Max Min Max 0.0295 0.035 0.75 0.90 A1 0.00 0.0039 0.00 0.10 A2 0.0275 0.0314 0.70 0.80 b 0.0157 0.0197 0.40 0.50 b1 0.0118 0.0157 0.30 0.40 c 0.0031 0.0078 0.08 0.20 D 0.1141 2.90 REF E 0.1023 0.1181 2.60 3.00 E1 0.0590 0.0069 1.50 1.70 e 0.0374 0.95 BSC e1 0.0748 1.90 BSC L 0.0118 0.0236 0.30 0.60 L1 0.0236 REF 0.60 REF L2 0.0098 BSC 0.25 BSC R 0.0039 ….. 0.10 ….. R1 0.0039 0.0098 0.10 0.25 θ 0° 8° 0° 8° y …. 0.0039 …. 0.10 Rev. 1 | Page 7 of 8 | www.onsemi.com PCS3P6100A Ordering Codes Part Number PCS3I6100AG-06JR Marking AB2 Package Type Temperature 6L-TSOT23 (6L-TSOT26), TAPE & REEL, Green -40°C to +85°C A “microdot” placed at the end of last row of marking or just below the last row toward the center of package indicates Pb-free. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. U.S Patent Pending; Timing-Safe and Active Bead are trademarks of PulseCore Semiconductor, a wholly owned subsidiary of ON Semiconductor. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative