Teccor® brand Thyristors
1 Amp Standard SCRs
Sx01E & SxN1 Series
Description
Excellent for lower current heat, lamp, and audible alarm
controls for home goods.
Standard phase control SCRs are triggered with few
milliamperes of current at less than 1.5V potential.
Features & Benefits
t3P)4DPNQMJBOU
t(MBTToQBTTJWBUFE
junctions
t7PMUBHFDBQBCJMJUZVQ
to 600 V
t4VSHFDBQBCJMJUZVQUP
30 A
Applications
Main Features
IT(RMS)
VDRM /VRRM
I(5
Value
Unit
1
A
400 to 600
V
10
mA
5ZQJDBMBQQMJDBUJPOTBSF"$TPMJETUBUFTXJUDIFT
nVJEMFWFMTFOTPSTTUSPCFTBOEDBQBDJUJWFEJTDIBSHF
JHOJUJPOTZTUFNT
1.0A SCRs
Symbol
Schematic Symbol
A
K
G
Absolute Maximum Ratings — Standard SCRs
Parameter
Test Conditions
Value
IT(RMS)
Symbol
RMS on-state current
TC = 90°C
1
A
IT(AV)
"WFSBHFPOTUBUFDVSSFOU
TC = 90°C
0.64
A
TJOHMFIBMGDZDMFG)[
TJ (initial) = 25°C
25
TJOHMFIBMGDZDMFG)[
TJ (initial) = 25°C
30
I2t Value for fusing
tp = 8.3 ms
3.7
A2s
Critical rate of rise of on-state current
G)[5J = 125°C
50
A/μs
Peak gate current
TJ = 125°C
1.5
A
"WFSBHFHBUFQPXFSEJTTJQBUJPO
TJ = 125°C
0.3
W
Storage temperature range
-40 to 150
°C
Operating junction temperature range
-40 to 125
°C
ITSM
I 2t
di/dt
I(.
P("7
Tstg
TJ
1FBLOPOSFQFUJUJWFTVSHFDVSSFOU
©2010 Littelfuse, Inc
Specifications are subject to change without notice.
Please refer to http://www.littelfuse.com for current information.
183
Revised: March 31, 2010 03:44 PM
Unit
A
Sx01E & SxN1 Series
Teccor® brand Thyristors
1 Amp Standard SCRs
Electrical Characteristics (TJ = 25°C, unless otherwise specified)
Symbol
Test Conditions
Value
MAX.
10
MIN.
1
MAX.
1.5
Unit
mA
I(5
VD73L = 60 8
V(5
EWEU
VD = VDRMHBUFPQFO5J = 100°C
V
20
MIN.
V/μs
VD = VDRMHBUFPQFO5J = 125°C
40
V(%
VD = VDRM3L = 3.3 k85J = 125°C
MIN.
0.2
V
I)
IT = 200mA (initial)
MAX.
30
mA
tq
(1)
MAX.
35
μs
tgt
I( = 2 x I(518T*T = 2A
TYP.
2
μs
(1) IT"UpTEWEU7TEJEU"T
Static Characteristics
Symbol
VTM
Test Conditions
IT"UpT
Value
Unit
1.6
V
MAX.
TJ = 25°C
IDRM / IRRM
VDRM = VRRM
10
TJ = 100°C
200
MAX.
TJ = 125°C
μA
500
Thermal Resistances
Symbol
Parameter
RR(J-C)
Junction to case (AC)
RR(J-A)
Junction to ambient
Value
Sx01E
50
SxN1
35*
Sx01E
145
Unit
°C/W
°C/W
/PUFTYWPMUBHF
* = Mounted on 1 cm2 copper (two-ounce) foil surface
Sx01E & SxN1 Series
184
Revised: March 31, 2010 03:44 PM
©2010 Littelfuse, Inc
Specifications are subject to change without notice.
Please refer to http://www.littelfuse.com for current information.
Teccor® brand Thyristors
1 Amp Standard SCRs
Figure 1: Normalized DC Gate Trigger Current
vs. Junction Temperature
Figure 2: Normalized DC Gate Trigger Voltage
vs. Junction Temperature
2.0
Ratio of VGT / VGT (TJ = 25°C)
Ratio of IGT / IGT (TJ = 25°C)
2.0
1.5
1.0
0.5
0.0
1.5
1.0
0.5
0.0
-40
-15
10
35
60
85
110
125
-40
-15
10
85
110
125
Figure 4: On-State Current vs. On-State
Voltage (Typical)
Instantaneous On-state Current (iT) – Amps
2.0
Ratio of IH/IH (TJ = 25°C)
60
1.5
1.0
0.5
25
TJ = 25°C
1.0A SCRs
Figure 3: Normalized DC Holding Current
vs. Junction Temperature
20
15
10
5
0
0.0
-40
-15
10
35
60
85
110
0.7
125
0.8
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0.1
0.2
0.3
0.4
0.5
0.6
©2010 Littelfuse, Inc
1.1
1.2
1.3
1.4
1.5
1.6
0.7
0.8
0.9
130
125
120
115
110
105
100
95
90
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
85
80
0.0
1.0
RMS On-State Current [IT(RMS)] - Amps
Specifications are subject to change without notice.
Please refer to http://www.littelfuse.com for current information.
1.0
Figure 6: Maximum Allowable Case Temperature
vs. RMS On-State Current
Maximum Allowable Case Temperature (TC) - °C
Figure 5: Power Dissipation (Typical)
vs. RMS On-State Current
0.0
0.9
Instantaneous On-state Voltage (vT) – Volts
Junction Temperature (TJ) -- (°C)
Average On-State Power Dissipation [PD(AV)] - (Watts)
35
Junction Temperature (TJ) -- (°C)
Junction Temperature (TJ) -- (°C)
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
RMS On-State Current [IT(RMS)] - Amps
185
Revised: March 31, 2010 03:44 PM
Sx01E & SxN1 Series
Teccor® brand Thyristors
1 Amp Standard SCRs
Figure 8: Maximum Allowable Ambient Temperature
vs. RMS On-State Current
130
Maximum Allowable Ambient Temperature (TA) - °C
Maximum Allowable Case Temperature (TC) - °C
Figure 7: Maximum Allowable Case Temperature
vs. Average On-State Current
125
120
115
110
105
100
95
90
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
85
80
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
120
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
FREE AIR RATING
100
80
60
40
20
0
0.0
0.8
0.1
0.2
Figure 9: Maximum Allowable Ambient Temperature
vs. Average On-State Current
0.4
0.5
0.6
0.7
0.8
0.9
1.0
Figure 10: Peak Capacitor Discharge Current
120
100
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
FREE AIR RATING
100
Peak Discharge Current (ITM) - Amps
Maximum Allowable Ambient Temperature
(TA) - °C
0.3
RMS On-State Current [IT(RMS)] - Amps
Average On-State Current [IT(AVE)] - Amps
80
60
40
20
10
ITRM
tW
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
1
0.7
0.5
1.0
10.0
50.0
Pulse Current Duration (tW) - ms
Average On-State Current [IT(AVE)] - Amps
Figure 11: Peak Capacitor Discharge Current Derating
1.2
Normalized Peak Current
1.0
0.8
0.6
0.4
0.2
0.0
0
25
50
75
100
125
150
Case Temperature (TC) - °C
Sx01E & SxN1 Series
186
Revised: March 31, 2010 03:44 PM
©2010 Littelfuse, Inc
Specifications are subject to change without notice.
Please refer to http://www.littelfuse.com for current information.
Teccor® brand Thyristors
1 Amp Standard SCRs
Figure 12: Surge Peak On-State Current vs. Number of Cycles
Peak Surge (Non-repetitive)
On-state Current (ITSM) – Amps
100.0
4611-:'3&26&/$:)[4JOVTPJEBM
-0"%3FTJTUJWF
RMS On-State Current: [IT(RMS)]: Maximum Rated
Value at Specified Case Temperature
Notes:
(BUFDPOUSPMNBZCFMPTUEVSJOHBOEJNNFEJBUFMZ
GPMMPXJOHTVSHFDVSSFOUJOUFSWBM
0WFSMPBENBZOPUCFSFQFBUFEVOUJMKVODUJPO
UFNQFSBUVSFIBTSFUVSOFEUPTUFBEZTUBUF
SBUFEWBMVF
10.0
1.0
0.1
1
10
100
1000
Surge Current Duration -- Full Cycles
Soldering Parameters
- Temperature Min (Ts(min))
150°C
- Temperature Max (Ts(max))
200°C
- Time (min to max) (ts)
oTFDT
Average ramp up rate (Liquidus Temp)
(TL) to peak
5°C/second max
TS(max) to TL - Ramp-up Rate
5°C/second max
Reflow
- Temperature (TL) (Liquidus)
217°C
- Temperature (tL)
oTFDPOET
260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)
oTFDPOET
Ramp-down Rate
5°C/second max
Time 25°C to peak Temperature (TP)
8 minutes Max.
Do not exceed
280°C
©2010 Littelfuse, Inc
Ramp-up
TL
tL
TS(max)
Preheat
Ramp-do
Ramp-down
TS(min)
tS
25
Peak Temperature (TP)
Specifications are subject to change without notice.
Please refer to http://www.littelfuse.com for current information.
tP
TP
time to peak temperature
187
Revised: March 31, 2010 03:44 PM
Time
Sx01E & SxN1 Series
1.0A SCRs
Pre Heat
1Co'SFFBTTFNCMZ
Temperature
Reflow Condition
Teccor® brand Thyristors
1 Amp Standard SCRs
Physical Specifications
Environmental Specifications
Test
Terminal Finish
.BUUF5JOQMBUFE
Body Material
6-SFDPHOJ[FEFQPYZNFFUJOHnBNNBCJMJUZ
classification 94V-0
Specifications and Conditions
AC Blocking
Lead Material
Temperature Cycling
$PQQFS"MMPZ
Temperature/
Humidity
Design Considerations
High Temp Storage
$BSFGVMTFMFDUJPOPGUIFDPSSFDUEFWJDFGPSUIFBQQMJDBUJPOT
PQFSBUJOHQBSBNFUFSTBOEFOWJSPONFOUXJMMHPBMPOHXBZ
UPXBSEFYUFOEJOHUIFPQFSBUJOHMJGFPGUIF5IZSJTUPS(PPE
design practice should limit the maximum continuous
DVSSFOUUISPVHIUIFNBJOUFSNJOBMTUPPGUIFEFWJDF
SBUJOH0UIFSXBZTUPFOTVSFMPOHMJGFGPSBQPXFSEJTDSFUF
semiconductor are proper heat sinking and selection of
WPMUBHFSBUJOHTGPSXPSTUDBTFDPOEJUJPOT0WFSIFBUJOH
PWFSWPMUBHFJODMVEJOHEWEU
BOETVSHFDVSSFOUTBSF
the main killers of semiconductors. Correct mounting,
soldering, and forming of the leads also help protect
against component damage.
Low-Temp Storage
MIL-STD-750, M-1040, Cond A Applied
1FBL"$WPMUBHF!¡$GPSIPVST
MIL-STD-750, M-1051,
DZDMFT¡$UP¡$NJO
dwell-time
EIA / JEDEC, JESD22-A101
IPVST7%$¡$
SFMIVNJEJUZ
MIL-STD-750, M-1031,
IPVST¡$
IPVST¡$
MIL-STD-750, M-1056
DZDMFT¡$UP¡$NJOEXFMM
UJNFBUFBDIUFNQFSBUVSFTFDNBY
transfer time between temperature
EIA / JEDEC, JESD22-A102
168 hours (121°C at 2 ATMs) and
3)
Thermal Shock
Autoclave
Resistance to
Solder Heat
MIL-STD-750 Method 2031
Solderability
"/4*+45%DBUFHPSZ5FTU"
Lead Bend
MIL-STD-750, M-2036 Cond E
Dimensions – TO-92 (E Package)
TC Measuring Point
Dimension
A
B
Cathode
Anode
Gate
Inches
Millimeters
Min
Max
A
0.176
0.196
B
0.500
D
0.095
E
0.150
Min
Max
4.47
4.98
12.70
0.105
2.41
2.67
3.81
F
0.046
0.054
1.16
1.37
(
0.135
0.145
3.43
3.68
)
0.088
0.096
2.23
2.44
J
0.176
0.186
4.47
4.73
K
0.088
0.096
2.23
2.44
L
0.013
0.019
0.33
0.48
M
0.013
0.017
0.33
0.43
"MMMFBETJOTVMBUFEGSPNDBTF$BTFJTFMFDUSJDBMMZOPODPOEVDUJWF
E
H
M
G
F
L
D
K
J
Sx01E & SxN1 Series
188
Revised: March 31, 2010 03:44 PM
©2010 Littelfuse, Inc
Specifications are subject to change without notice.
Please refer to http://www.littelfuse.com for current information.
Teccor® brand Thyristors
1 Amp Standard SCRs
Dimensions - Compak (C Package)
TC / TL Temperature
Measurement Point
Dimension
Gate
B
D
M
P
A
C
Cathode
Anode
L
J
0.079
(2.0)
K
0.079
(2.0)
Min
Max
0.130
0.156
3.30
3.95
B
0.201
0.220
5.10
5.60
C
0.077
0.087
1.95
2.20
D
0.159
0.181
4.05
4.60
E
0.030
0.063
0.75
1.60
F
0.075
0.096
1.90
2.45
(
0.002
0.008
0.05
0.20
)
0.077
0.104
1.95
2.65
F
H
E
Millimeters
Max
A
N
Inches
Min
G
0.079
(2.0)
0.040
(1.0)
0.030
(0.76)
0.110
(2.8)
J
0.043
0.053
1.09
1.35
K
0.006
0.016
0.15
0.41
L
0.030
0.055
0.76
1.40
M
0.022
0.028
0.56
0.71
N
0.027
0.033
0.69
0.84
P
0.052
0.058
1.32
1.47
Dimensions are in inches
(and millimeters).
Product Selector
Part Number
Voltage
Gate Sensitivity
Type
X
10mA
Standard SCR
TO-92
X
10mA
Standard SCR
Compak
400V
600V
Sx01E
X
SxN1
X
800V
1000V
Package
Note: x = Voltage
Packing Options
Part Number
Marking
Weight
Packing Mode
Base Quantity
Sx01E
Sx01E
0.19 g
Bulk
2000
Sx01ERP
Sx01E
0.19 g
Reel Pack
2000
Sx01EAP
Sx01E
0.19 g
Ammo Pack
2000
SxN1RP
SxN1
0.08 g
Embossed Carrier
2500
Note: x = Voltage
©2010 Littelfuse, Inc
Specifications are subject to change without notice.
Please refer to http://www.littelfuse.com for current information.
189
Revised: March 31, 2010 03:44 PM
Sx01E & SxN1 Series
1.0A SCRs
Pad Outline
Teccor® brand Thyristors
1 Amp Standard SCRs
TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications
Meets all EIA-468-B 1994 Standards
1.6
(41.0)
0.236
(6.0)
0.708
(18.0)
0.02 (0.5)
0.098 (2.5) MAX
1.26
(32.0)
0.354
(9.0)
0.5
(12.7)
Cathode
0.1 (2.54)
0.2 (5.08)
Anode
Gate
0.157 DIA
(4.0)
14.17(360.0)
Flat up
1.97
(50.0)
Dimensions
are in inches
(and millimeters).
Direction of Feed
TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Specifications
Meets all EIA-468-B 1994 Standards
0.236
(6.0)
1.62
(41.2)
0.708
(18.0)
0.02 (0.5)
0.098 (2.5) MAX
1.27
(32.2)
0.354
(9.0)
Anode
0.1 (2.54)
0.5
(12.7)
0.2 (5.08)
0.157
(4.0) DIA
Cathode
Gate
Flat down
n of
Directio
Feed
25 Devices per fold
1.85
(47.0)
12.2
(310.0)
1.85
(47.0)
Dimensions
are in inches
(and millimeters).
13.3
(338.0)
Sx01E & SxN1 Series
190
Revised: March 31, 2010 03:44 PM
©2010 Littelfuse, Inc
Specifications are subject to change without notice.
Please refer to http://www.littelfuse.com for current information.
Teccor® brand Thyristors
1 Amp Standard SCRs
Compak Embossed Carrier Reel Pack (RP) Specifications
Meets all EIA-481-1 Standards
0.157
(4.0)
0.47
(12.0)
Anode
0.36
(9.2)
8.0
0.315
(8.0)
Gate
0.059 DIA
(1.5)
Cathode
Cover tape
12.99
(330.0)
0.512 (13.0) Arbor
Hole Dia.
Dimensions
are in inches
(and millimeters).
0.49
(12.4)
Part Numbering System
S 6 01 E
Part Marking System
75
DEVICE TYPE
S: SCR
TO-92 (E Package)
Lead Form Dimensions
xx: Lead Form Option
S601E
Compak (C Package)
S6N1
®
®
VOLTAGE RATING
4: 400V
6: 600V
CURRENT RATING
01: 1A (TO-92)
N: 1A (Compak)
©2010 Littelfuse, Inc
Specifications are subject to change without notice.
Please refer to http://www.littelfuse.com for current information.
yxxxx
yxxxx
SENSITIVITY & TYPE
[blank]: 10 mA (TO-92)
1: 10 mA (Compak)
PACKAGE TYPE
E: TO-92 SCR
N: Compak
191
Revised: March 31, 2010 03:44 PM
Sx01E & SxN1 Series
1.0A SCRs
Direction of Feed
Teccor® brand Thyristors
192
Revised: March 31, 2010 03:44 PM
©2010 Littelfuse, Inc
Specifications are subject to change without notice.