View detail for Symmetrical 8-tap FIR Filter Macro (FIR8S)

PC7410
PowerPC 7410 RISC Microprocessor
Datasheet
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
22.8 SPECint95 (estimated), 17SPECfp95 at 500 MHz (estimated)
917MIPS at 500 MHz
Selectable Bus Clock (14 CPU Bus Dividers Up To 9x)
Seven Selectable Core-to-L2 Frequency Divisors
Selectable 603 Interface Voltage Below 3.3V (1.8V, 2.5V)
Selectable L2 interface of 1.8V or 2.5V
PD Typical 5.3W at 500 MHz, Full Operating Conditions
Nap, Doze and Sleep Modes for Power Saving
Superscalar (Four Instructions fetched per Clock Cycle)
4 GB Direct Addressing Range
Virtual Memory: 4 hexabytes (252)
64-bit Data and 32-bit Address Bus Interface
32 KB Instruction and Data Cache
Eight Independent Execution Units and Three Register Files
Write-back and Write-through Operations
fINT Max = 450 MHz 500 MHz
fBUS Max = 133 MHz
Description
The PC7410 is the second microprocessor that uses the fourth (G4) full implementation of the PowerPC Reduced Instruction Set Computer (RISC) architecture. It is fully JTAG-compliant.
The PC7410 maintains some of the characteristics of G3 microprocessors:
• The design is superscalar, capable of issuing three instructions per clock cycle into eight independent execution units
• The microprocessor provides four software controllable power-saving modes and a thermal assist unit management
• The microprocessor has separate 32-Kbyte, physically-addressed instruction and data caches with dedicated L2 cache
interface with on-chip L2 tags
In addition, the PC7410 integrates full hardware-based multiprocessing capability, including a 5-state cache coherency protocol (4 MESI states plus a fifth state for shared intervention) and an implementation of the new AltiVec® technology
instruction set.
New features have been developed to make latency equal for double-precision and single-precision floating-point operations involving multiplication. Additionally, in memory subsystem (MSS) bandwidth, the PC7410 offers an optional, highbandwidth MPX bus interface.
Unlike the PC7400, the PC7410 does not support the 3.3V I/O on the L2 cache interface.
Visit our website: www.e2v.com
for the latest version of the datasheet
e2v semiconductors SAS 2007
PC7410
Screening
• CBGA Upscreenings Based on e2v Standards
• Full Military Temperature Range (TJ = -55° C, +125° C),
Industrial Temperature Range (TJ = -40° C, +110° C)
• CI-CGA Package Version, HiTCE Package Version
2
0832F–HIREL–02/07
e2v semiconductors SAS 2007
SRs
(Shadow)
64-entry BTIC/512-entry BHT
LR/CTR
128-entry
ITLB
Instruction
Queue
6-word
32-Kbyte
iCache
Tags
IBAT
Array
Data MMU
Dispatch Unit
EA
SRs
(Original)
2 Instructions
PA
128-entry
DTLB
Tags
DBAT
Array
32-Kbyte
DCache
64-bit
(2 Instructions)
Reservation
Station
Reservation
Station
Reservation
Station
VR File
Reservation
Station
Reservation
Station
Reservation
Station
2-entry
GPR File
6 Rename
Buffers
6 Rename
Buffers
Vector
ALU
Integer
Unit 1
Integer
Unit 2
Add-Multiplydivide
- Add -
- Add EA Calculation
Finished Stores
Completed
Stores
System
Register
Unit
Reservation
Station
6 Rename
Buffers
Load/Store
Unit
32-bit
Vector
Permute
Unit
FPR File
PC7410 Microprocessor Block Diagram
Branch Processing Unit
Fetcher
Additional features
Time Base
Counter/Decrementer
Clock Multiplier
JTAG/COP Interface
Thermal/Power Management
Performance Monitor
1. Block Diagram
Instruction MMU
Instruction Unit
Figure 1-1.
e2v semiconductors SAS 2007
128 bits
(4 instructions)
64-bit
Floating
64-bit Point Unit
Add-Multiplydivide
VSIU VCIU VFPU
FPSCR
VSCR
32-bit
32-bit
128-bit
128-bit
128 bits
Completion Unit
L2 Controller
L2 Data
L2 Tags
Transaction
L2CR
Queue
8-entry
Reorder Buffer
0832F–HIREL–02/07
Bus Interface Unit
L2 Miss
Data
Transaction
Queue
Memory Subsystem
Data Reload
Data Reload
Buffer
Table
L2PMCR
L2 Castout
Instruction
Reload Buffer
64- or 32-bit L2 Data Bus
32-bit Address Bus
3
64-bit Data Bus
Instruction
Reload Table
PC7410
19-bit L2 Address Bus
PC7410
2. General Parameters
Table 2-1 provides a summary of the general parameters of the PC7410.
Table 2-1.
Device Parameters
Parameter
Description
Technology
0.18 µm CMOS, six-layer metal
Die size
6.32 mm × 8.26 mm (52 mm2)
Transistor count
10.5 million
Logic design
Fully-static
Packages
Surface-mount 360 Ceramic Ball Grid Array (CBGA)
Surface mount 360 high coefficient of thermal expansion
ceramic ball grid array (HiTCE)
Surface mount 360-column Ci-CGA Package
Core power supply
1.8V ± 100 mV dc or 1.5V ± 50 mV dc (nominal; see Table 6-3 on page 11 for
Recommended Operating Conditions)
I/O power supply
1.8V ± 100 mV dc or
2.5V ± 100 mV
3.3V ± 165 mV (603 bus only)(1)
(input thresholds are configuration pin selectable)
Note:
1. 3.3V I/O bus not supported for 1.5V core power supply processor version.
3. Overview
This section summarizes features of the PC7410’s implementation of the PowerPC architecture. Major
features of the PC7410 are as follows:
• Branch Processing Unit
– Four instructions fetched per clock
– One branch processed per cycle (plus resolving two speculations)
– Up to one speculative stream in execution, one additional speculative stream in fetch
– 512-entry Branch History Table (BHT) for dynamic prediction
– 64-entry, 4-way set associative Branch Target Instruction Cache (BTIC) for eliminating
branch delay slots
• Dispatch Unit
– Full hardware detection of dependencies (resolved in the execution units)
– Dispatch two instructions to eight independent units (system, branch, load/store, fixed-point
unit 1, fixed-point unit 2, floating-point, AltiVec permute, AltiVec ALU)
– Serialization control (predispatch, postdispatch, execution serialization)
• Decode
– Register file access
– Forwarding control
– Partial instruction decode
4
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
• Completion
– 8-entry completion buffer
– Instruction tracking and peak completion of two instructions per cycle
– Completion of instructions in program order while supporting out-of-order instruction
execution, completion serialization and all instruction flow changes
• Fixed-point Units (FXUs) that Share 32 GPRs for Integer Operands
– Fixed-point Unit 1 (FXU1): multiply, divide, shift, rotate, arithmetic, logical
– Fixed-point Unit 2 (FXU2)—shift, rotate, arithmetic, logical
– Single-cycle arithmetic, shifts, rotates, logical
– Multiply and divide support (multi-cycle)
– Early out multiply
• Three-stage Floating-point Unit and a 32-entry FPR File
– Support for IEEE-754 standard single- and double-precision floating-point arithmetic
– Three-cycle latency, one-cycle throughput (single or double precision)
– Hardware support for divide
– Hardware support for denormalized numbers
– Time deterministic non-IEEE mode
• System Unit
– Executes CR logical instructions and miscellaneous system instructions
– Special register transfer instructions
• AltiVec Unit
– Full 128-bit data paths
– Two dispatchable units: vector permute unit and vector ALU unit
– Contains its own 32-entry 128-bit Vector Register File (VRF) with six renames
– The vector ALU unit is further sub-divided into the Vector Simple Integer Unit (VSIU), the
Vector Complex Integer Unit (VCIU) and the Vector Floating-point Unit (VFPU)
– Fully pipelined
• Load/Store Unit
– One-cycle load or store cache access (byte, half-word, word, double-word)
– Two-cycle load latency with one-cycle throughput
– Effective address generation
– Hits under misses (multiple outstanding misses)
– Single-cycle unaligned access within double-word boundary
– Alignment, zero padding, sign extend for integer register file
– Floating-point internal format conversion (alignment, normalization)
– Sequencing for load/store multiples and string operations
– Store gathering
– Executes the cache and TLB instructions
– Big- and little-endian byte addressing supported
– Misaligned little-endian supported
5
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
– Supports FXU, FPU, and AltiVec load/store traffic
– Complete support for all four architecture AltiVec DST streams
• Level 1 (L1) Cache Structure
– 32K 32-byte line, 8-way set associative instruction cache (iL1)
– 32K 32-byte line, 8-way set associative data cache (dL1)
– Single-cycle cache access
– Pseudo Least-recently-used (LRU) replacement
– Data cache supports AltiVec LRU and transient instructions algorithm
– Copy-back or write-through data cache (on a page-per-page basis)
– Supports all PowerPC memory coherency modes
– Non-blocking instruction and data cache
– Separate copy of data cache tags for efficient snooping
– No snooping of instruction cache except for ICBI instruction
• Level 2 (L2) Cache Interface
– Internal L2 cache controller and tags; external data SRAMs
– 512K, 1M and 2-Mbyte 2-way set associative L2 cache support
– Copyback or write-through data cache (on a page basis or for all L2)
– 32-byte (512K), 64-byte (1M), or 128-byte (2M) sectored line size
– Supports pipelined (register-register) synchronous burst SRAMs and pipelined (registerregister) late-write synchronous burst SRAMs
– Supports direct mapped mode for 256K, 512K, 1M or 2 Mbytes of SRAM (either all, half or
none of L2 SRAM must be configured as direct mapped
– Core-to-L2 frequency divisors of ÷1, ÷1.5, ÷2, ÷2.5, ÷3, ÷3.5, and ÷4 supported
– 64-bit data bus which also support 32-bits bus mode
– Selectable interface voltages of 1.8V and 2.5V
• Memory Management Unit
– 128 entry, 2-way set associative instruction TLB
– 128 entry, 2-way set associative data TLB
– Hardware reload for TLBs
– Four instruction BATs and four data BATs
– Virtual memory support for up to four petabytes (252) of virtual memory
– Real memory support for up to four gigabytes (232) of physical memory
– Snooped and invalidated for TLBI instructions
• Efficient Data Flow
– All data buses between VRF, load/store unit, dL1, iL1, L2 and the bus are 128 bits wide
– dL1 is fully pipelined to provide 128 bits per cycle to/from the VRF
– L2 is fully pipelined to provide 128 bits per L2 clock cycle to the L1s
– Up to eight outstanding out-of-order cache misses between dL1 and L2/bus
– Up to seven outstanding out-of-order transactions on the bus
6
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
– Load folding to fold new dL1 misses into older outstanding load and store misses to the
same line
– Store miss merging for multiple store misses to the same line. Only coherency action taken
(i.e., address only) for store misses merged to all 32 bytes of a cache line (no data tenure
needed)
– Two-entry finished store queue and four-entry completed store queue between load/store
unit and dL1
– Separate additional queues for efficient buffering of outbound data (castouts, write throughs,
etc.) from dL1 and L2
• Bus Interface
– MPX bus extension to 60X processor interface
– Mode-compatible with 60x processor interface
– 32-bit address bus
– 64-bit data bus
– Bus-to-core frequency multipliers of 2x, 2.5x, 3x, 3.5x, 4x, 4.5x, 5x, 5.5x, 6x, 6.5x, 7x, 7.5x,
8x, 9x supported
– Selectable interface voltages of 1.8V, 2.5V and 3.3V
• Power Management
– Low-power design with thermal requirements very similar to PC740 and PC750
– Low voltage 1.8V or 1.5V processor core
– Selectable interface voltages of 1.8V can reduce power in output buffers
– Three static power saving modes: doze, nap, and sleep
– Dynamic power management
• Testability
– LSSD scan design
– IEEE 1149.1 JTAG interface
– Array Built-in Self Test (ABIST) – factory test only
– Redundancy on L1 data arrays and L2 tag arrays
• Reliability and Serviceability
– Parity checking on 60x and L2 cache buses
7
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
4. Signal Description
Figure 4-1.
PC7410 Microprocessor Signal Groups
L2OVDD
GND
L2AVDD
BR
Address
Arbitration
BG
ABB/AMON[0]
Address
Start
TS
A[0:31]
Address
Bus
AP[0:3]
TT[0:4]
TBST
TSIZ[0:2]
Transfer
Attribute
GBL
WT
CI
1
13
49
19
1
64
1
8
1
Address
Termination
AACK
ARTRY
DBG
Data
Arbitration
DBWO, DTI(0)
1
1
32
2
4
1
5
1
1
1
1
3
1
1
1
1
1
1
PCX7410
1
D[0:63]
Data
Transfer
DP[0:7]
1
1
1
2
1
1
1
1
1
1
1
1
1
64
1
8
4
DTI(2)
TA
Data
Termination
1
1
DBB, DMON(0)
DTI1
TEA
L2DATA[0:63]
L2DP[0:7]
L2 Cache
Address/Data
1
1
1
CHK
L2ADDR[0:18]
1
1
1
VDD
20
OVDD
1
L2SYNC_OUT
L2ZZ
INT
SMI
MCP
SRESET
HRESET
CKSTP_IN
Interrupts
Reset
CKSTP_OUT
HIT
SHDO, SHD1
RSRV
TBEN
EMODE
QREQ
Processor
Status
Control
QACK
DRDY
SYSCLK
PLL_CFG[0:3]
CLK_OUT
JTAG:COP
3
1
L2 Cache
Clock/Control
L2SYNC_IN
Factory Test
L1_TSTCLK,
L2_TSTCLK
BVSEL
1
12
L2CLKOUTA,
L2CLKOUTB
5
1
1
L2CE
L2WE
L2VSEL
Clock
Control
Test Interface
LSSD_MODE
I/O Voltage
Selection
AVDD
8
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
5. Detailed Specification
This specification describes the specific requirements for the microprocessor PC7410 in compliance with
e2v standard screening.
6. Applicable Documents
1. MIL-STD-883: Test methods and procedures for electronics
2. MIL-PRF-38535: Appendix A: General specifications for microcircuits
The microcircuits are in accordance with the applicable documents and as specified herein.
6.1
Design and Construction
6.1.1
6.2
Terminal Connections
Depending on the package, the terminal connections are as shown in Table 12-1 on page 33, Table 6-3
on page 11 and Figure 4-1 on page 8.
Absolute Maximum Ratings
Table 6-1.
Absolute Maximum Ratings(1)
Symbol
Characteristic
Value
VDD
Core supply voltage
-0.3 to 2.1(4)
V
(4)
V
PLL supply voltage
AVDD
L2AVDD
L2 DLL supply voltage
-0.3 to 2.1
Unit
(4)
-0.3 to 2.1
V
(3)(6)
OVDD
60x bus supply voltage
-0.3 to 3.465
L2OVDD
L2 bus supply voltage
-0.3 to 2.6(3)
VIN
Processor bus input voltage
-0.3 to OVDD + 0,2V(2)(5)
VIN
L2 bus input voltage
-0.3 to L2OVDD + 0,2V
V
VIN
JTAG signal input voltage
-0.3 to OVDD + 0,2V
V
TSTG
Storage temperature range
-55 to 150
°C
Rework temperature
260
°C
Notes:
V
V
V
(2)(5)
1. Functional and tested operating conditions are given in Table 6-3 on page 11. Absolute maximum ratings are stress ratings
only. Stresses beyond those listed may affect device reliability or cause permanent damage to the device.
2. Caution: VIN must not exceed OVDD or L2OVDD by more than 0.2V at any time including during power-on reset.
3. Caution: L2OVDD/OVDD must not exceed VDD/AVDD/L2AVDD by more than 2.0V at any time including during power-on reset;
this limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences.
4. Caution: VDD/AVDD/L2AVDD must not exceed L2OVDD/OVDD by more than 0.4V at any time including during power-on reset;
this limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences.
5. VIN may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 6-1 on page 10.
6. PC7410RXnnnLE (Rev 1.4) and later only. Previous revisions do not support 3.3V OVDD and have a maximum value OVDD of
-0.3 to 2.6V.
9
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 6-1.
Overshoot/Undershoot Voltage
(L2)OVDD + 20%
(L2)OVDD + 5%
(L2)OVDD
VIH
VIL
GND
GND - 0.3V
GND - 0.7V
Not to exceed
10% of tSYSCLK
The PC7410 provides several I/O voltages to support both compatibility with existing systems and migration to future systems. The PC7410 “core” voltage must always be provided at nominal voltage (see
Table 6-3 on page 11 for actual recommended core voltage). Voltage to the L2 I/Os and processor interface I/Os are provided through separate sets of supply pins and may be provided at the voltages shown
in Table 6-2. The input voltage threshold for each bus is selected by sampling the state of the voltage
select pins at the negation of the signal HRESET. The output voltage will swing from GND to the maximum voltage applied to the OVDD or L2OVDD power pins.
Table 6-2.
Input Threshold Voltage Setting
BVSEL Signal
Processor Bus Input
Threshold is Relative to:
L2VSEL Signal(3)
L2 Bus Input Threshold is
Relative to:
0(1)
1.8V
0
1.8
HRESET(1)(2)
2.5V
(1)(4)(5)
1
HRESET
Notes:
(6)
HRESET
2.5
3.3V
(7)
1
2.5
3.3V
(7)
HRESET
Not supported
1. Caution: The input threshold selection must agree with the OVDD/L2OVDD voltages supplied.
2. To select the 2.5V threshold option, L2VSEL/BVSEL should be tied to HRESET so that the two signals
change state together. This is the preferred method for selecting this mode operation.
3. To overcome the internal pull-up resistance, a pull-down resistance less than 250Ω should be used.
4. Default voltage setting if left unconnected (internal pulled-up). Parts Rev 1.4 and later only. Previous
revisions do not support 3.3V OVDD, the default voltage setting if left unconnected is 2.5V.
5. Parts Rev 1.4 and later only. Previous revisions do not support 3.3V OVDD, having BVSEL = 1 selects
the 2.5V threshold.
6. Parts Rev 1.4 and later only. Previous revisions do not support BVSEL = HRESET.
7. NSpec does not support the default OVDD setting of 3.3V. The BVSEL input must be tie either low or
HRESET.
10
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
6.3
Recommended Operating Conditions
Table 6-3.
Recommended Operating Conditions(1)
Recommended
Value
Symbol
Characteristic
VDD
Core supply voltage
1.8 ± 100 mV
or 1.5 ± 50 mV
V
AVDD
PLL supply voltage
1.8 ± 100 mV
or 1.5 ± 50 mV
V
L2AVDD
L2 DLL supply voltage
1.8 ± 100 mV
or 1.5 ± 50 mV
V
1.8 ± 100 mV
V
2.5 ± 100 mV
V
BVSEL = 1 or = HRESET
3.3 ± 165 mV
V
L2VSEL = 0
1.8 ± 100 mV
V
2.5 ± 100 mV
V
GND to OVDD
V
GND to L2OVDD
V
GND to OVDD
V
-55 to 125
°C
OVDD
BVSEL = 0
Processor bus supply voltage see note
OVDD
(2)(3)
BVSEL = HRESET
(4)
OVDD
L2OVDD
(3)
L2 bus supply voltage
(2)
L2OVDD
L2VSEL = 1
VIN
Processor bus
VIN
Input voltage
JTAG Signals
VIN
TJ
Notes:
L2 Bus
or L2VSEL = HRESET
Die-junction temperature
Unit
1. These are the recommended and tested operating conditions. Proper device operation outside of these conditions is not
guaranteed.
2. PC7410RXnnnLE (Rev 1.4) and later only. Previous revisions do not support 3.3V OVDD and have a recommended OVDD
value of 2.5V ±100 mV for BVSEL = 1.
3. PC7410RXnnnLE (Rev 1.4) and later only. Previous revisions do not support BVSEL = HRESET.
4. Not supported for N spec with VDD = 1.5V
11
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
7. Thermal Characteristics
7.1
Package Characteristics
Table 7-1.
Package Thermal Characteristics CBGA
Value
PC7410 CBGA
Unit
Junction-to-ambient thermal resistance, natural convection, single-layer (1s) board(1)(2)
24
° C/W
(1)(3)
17
° C/W
18
° C/W
16
° C/W
14
° C/W
13
° C/W
8
° C/W
< 0.1
° C/W
Symbol
Characteristic
RθJA
RθJMA
Junction-to-ambient thermal resistance, natural convection, four-layer (2s2p) board
RθJMA
Junction-to-ambient thermal resistance, 200 ft/min airflow, single-layer (1s) board
RθJMA
Junction-to-ambient thermal resistance, 400 ft/min airflow, single-layer (1s) board
(1)(3)
RθJMA
Junction-to-ambient thermal resistance, 200 ft/min airflow, four-layer (2s2p) board
RθJMA
Junction-to-ambient thermal resistance, 400 ft/min airflow, four-layer (2s2p) board
(4)
RθJB
Junction-to-board thermal resistance
RθJC
Junction-to-case thermal resistance(5)
Notes:
(1)(3)
1. Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance.
2. Per SEMI G38-87 and JEDEC JESD51-2 with the single layer board horizontal.
3. Per JEDEC JESD51-6 with the board horizontal.
4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883
Method 1012.1) with the calculated case temperature. The actual value of RθJC for the part is less than 0.1°C/W.
See “Thermal Management Information” on page 13 for more details about thermal management.
The board designer can choose between several commercially available heat sink types to place on the
PC7410. For exposed-die packaging technology as in Table 7-1, the intrinsic conduction thermal resistance paths are shown in Figure 7-1 on page 13.
7.1.1
Package Thermal Characteristics for HiTCE
Table 7-2 provides the package thermal characteristics for the PC7410, HiTCE.
Table 7-2.
Package Thermal Characteristics for HiTCE Package
Value
Characteristic
Symbol
PC7410 HiTCE
Unit
RθJ
6.8
° C/W
Junction-to-ambient thermal resistance, natural
convection, four-layer (2s2p) board(1)(2)
Rθ JMA
20.7
° C/W
Junction to board thermal resistance
RθJB
11.0
° C/W
Junction-to-bottom of balls
Notes:
(1)
1. Simulation, no convection air flow.
2. Per JEDEC JESD51-6 with the board horizontal.
12
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
7.1.2
Package Thermal Characteristics for CI-CGA
Table 7-3.
Package Thermal Characteristics for CI-CGA
Value
Characteristic
Symbol
PC7410 CI-CGA
Unit
RθJB
8.42
° C/W
Junction to board thermal resistance
7.2
Internal Package Conduction Resistance
Figure 7-1 depicts the primary heat transfer path for a package with an attached heat sink mounted on a
printed circuit board.
Heat generated on the active side of the chip is conducted through the silicon, then through the heat sink
attach material (or thermal interface material) and finally to the heat sink where it is removed by forcedair convection.
Since the silicon thermal resistance is quite small, for a first-order analysis the temperature drop in the
silicon may be neglected. Thus, the heat sink attach material and the heat sink conduction/convective
thermal resistances are the dominant terms.
Figure 7-1.
C4 Package with Heat Sink Mounted on a Printed Circuit Board
Radiation
External Resistance
Convection
Heat Sink
Thermal Interface Material
Die Junction
Die/Package
Package/Leads
Internal Resistance
Printed Circuit Board
External Resistance
7.3
Radiation
Convection
Thermal Management Information
This section provides thermal management information for the ceramic ball grid array (CBGA) package
for air-cooled applications. Proper thermal control design is primarily dependent upon the system-level
design – the heat sink, airflow and thermal interface material. To reduce the die-junction temperature,
heat sinks may be attached to the package by several methods: adhesive, spring clip to holes in the
printed-circuit board or package and mounting clip and screw assembly; see Figure 7-2 on page 14. This
spring force should not exceed 5.5 pounds of force. Ultimately, the final selection of an appropriate heat
sink depends on many factors such as thermal performance at a given air velocity, spatial volume, mass,
attachment method, assembly and cost.
13
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 7-2.
CBGA Package Cross-section with Heat Sink Options
Heat Sink
Heat Sink Clip
Adhesive or
Thermal Interface Material
Option
Printed-Circuit Board
7.3.1
Adhesives and Thermal Interface Materials
A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the
thermal contact resistance. For those applications where the heat sink is attached by spring clip mechanism, Figure 7-3 on page 15 shows the thermal performance of three thin-sheet thermal-interface
materials (silicone, graphite/oil, floroether oil), a bare joint and a joint with thermal grease as a function of
contact pressure. As shown, the performance of these thermal interface materials improves with increasing contact pressure. The use of thermal grease significantly reduces the interface thermal resistance.
That is, the bare joint results in a thermal resistance approximately seven times greater than the thermal
grease joint.
Heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board
(see Figure 7-2). This spring force should not exceed 5.5 pounds of force. Therefore, synthetic grease
offers the best thermal performance, considering the low interface pressure.
The board designer can choose between several types of thermal interface. Heat sink adhesive materials should be selected based upon high conductivity, yet must have adequate mechanical strength to
meet equipment shock/vibration requirements.
14
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 7-3.
Thermal Performance of Different Thermal Interface Materials
Silicone Sheet (0.006")
Bare Joint
Floroether Oil Sheet (0.007")
Graphite/Oil Sheet (0.005")
Synthetic Grease
Specific Thermal Resistance (K-in.2/W)
2
1.5
1
0.5
0
0
7.3.1.1
10
20
30
40
50
Contact Pressure (psi)
60
70
80
Heat Sink Selection Example
For preliminary heat sink sizing, the die-junction temperature can be expressed as follows:
T j = T a + T r + ( θ jc + θ int + θ sa ) × P d
where:
TJ = die-junction temperature
Ta = inlet cabinet ambient temperature
Tr = air temperature rise within the computer cabinet
θjc = junction-to-case thermal resistance
θint = adhesive or interface material thermal resistance
θsa = heat sink base-to-ambient thermal resistance
Pd = power dissipated by the device
During operation, the die-junction temperatures (TJ) should be maintained less than the value specified
in Table 6-3 on page 11. The temperature of the air cooling the component greatly depends upon the
ambient inlet air temperature and the air temperature rise within the electronic cabinet. An electronic
cabinet inlet-air temperature (Ta) may range from 30° C to 40° C. The air temperature rise within a cabinet (Tr) may be in the range of 5° C to 10° C. The thermal resistance of the thermal interface material
(θ int) is typically about 1° C/W. Assuming a Ta of 30° C, a Tr of 5° C, a CBGA package θ jc = 0.03, and a
power consumption (Pd) of 5.0 watts, the following expression for TJ is obtained:
T j = 30° C + 5° C + ( 0,03° C ⁄ W + 1,0° C ⁄ W + θ sa ) × 5W
15
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
For a Thermally heat sink #2328B, the heat sink-to-ambient thermal resistance (θsa) versus airflow velocity is shown in Figure 7-4.
Figure 7-4.
Thermalloy #2328B Heat Sink-to-ambient Thermal Resistance vs. Airflow Velocity
8
Thermalloy #2328B Pin-Fin Heat Sink
(25 x 28 x 15 mm)
Heat Sink Thermal Resistance (˚C/W)
7
6
5
4
3
2
1
0
0.5
1
1.5
2
2.5
Approach Air Velocity (m/s)
3
3.5
Assuming an air velocity of 0.5 m/s, the effective Rsa is 7° C/W, thus
T J = 30° C + 5° C + ( 0,03° C ⁄ W + 1,0° C ⁄ W + 7° C ⁄ W ) × 5W ,
resulting in a die-junction temperature of approximately 75° C which is well within the maximum operating temperature of the component.
Other heat sinks offered by Chip Coolers, IERC, Thermalloy, Wakefield Engineering and Aavid Engineering offer different heat sink-to-ambient thermal resistances and may or may not need air flow.
Though the die junction-to-ambient and the heat sink-to-ambient thermal resistances are a common figure of merit used for comparing the thermal performance of various microelectronic packaging
technologies, one should exercise caution when only using this metric in determining thermal management because no single parameter can adequately describe three-dimensional heat flow. The final diejunction operating temperature is not only a function of the component-level thermal resistance, but of
the system-level design and its operating conditions. In addition to the component's power consumption,
a number of factors affect the final operating die-junction temperature – airflow, board population (local
heat flux of adjacent components), heat sink efficiency, heat sink attach, heat sink placement, next-level
interconnect technology, system air temperature rise, altitude, etc.
16
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Due to the complexity and the many variations of system-level boundary conditions for today's microelectronic equipment, the combined effects of the heat transfer mechanisms (radiation, convection and
conduction) may vary widely. For these reasons, it is recommended to use conjugate heat transfer models for the board, as well as system-level designs.
To expedite system-level thermal analysis, several “compact” thermal-package models are available
within FLOTHERM®. These are available upon request.
8. Power Consideration
8.1
Power Management
The PC7410 provides four power modes, selectable by setting the appropriate control bits in the MSR
and HIDO registers. The four power modes are:
• Full-power: This is the default power state of the PC7410. The PC7410 is fully powered and the
internal functional units are operating at the full processor clock speed. If the dynamic power
management mode is enabled, functional units that are idle will automatically enter a low-power state
without affecting performance, software execution or external hardware.
• Doze: All the functional units of the PC7410 are disabled except for the time base/decrementer
registers and the bus snooping logic. When the processor is in doze mode, an external asynchronous
interrupt, a system management interrupt, a decrementer exception, a hard or soft reset or machine
check brings the PC7410 into the full-power state. The PC7410 in doze mode maintains the PLL in a
fully powered state and locked to the system external clock input (SYSCLK) so a transition to the fullpower state takes only a few processor clock cycles.
• Nap: The nap mode further reduces power consumption by disabling bus snooping, leaving only the
time base register and the PLL in a powered state. The PC7410 returns to the full-power state upon
receipt of an external asynchronous interrupt, a system management interrupt, a decrementer
exception, a hard or soft reset or a machine check input (MCP). A return to full-power state from a
nap state takes only a few processor clock cycles. When the processor is in nap mode, if QACK is
negated, the processor is put in doze mode to support snooping.
• Sleep: Sleep mode minimizes power consumption by disabling all internal functional units, after which
external system logic may disable the PLL and SYSCLK. Returning the PC7410 to the full-power
state requires the enabling of the PLL and SYSCLK, followed by the assertion of an external
asynchronous interrupt, a system management interrupt, a hard or soft reset or a machine check
input (MCP) signal after the time required to relock the PLL.
17
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
8.2
Power Dissipation
Table 8-1.
Power Consumption for PC7410 (1.8V)
Processor (CPU) Frequency
Power Mode
Core power supply
400 MHz
450 MHz
500 MHz
1.5V
1.8V
1.5V
1.8V
1.8 V
Unit
2.92
4.2
3.29
4.7
5.3
W
6.6
9.5
7.43
10.7
11.9
W
3.6
4.3
4.1
4.8
5.3
W
1.35
1.35
1.5
1.5
1.65
W
1.3
1.3
1.45
1.45
1.6
W
600
600
600
600
600
mW
1.1
1.1
1.1
1.1
1.1
W
Full-On Mode
Typical(1)(3)
Maximum
(1)(2)(4)(5)
Doze Mode
Maximum(1)(2)(5)
Nap Mode
Maximum(1)(2)(5)
Sleep Mode
Maximum(1)(2)(5)
Sleep Mode - PLL and DLL Disabled
Typical(1)(3)
Maximum
Notes:
(1)(2)(5)
1. These values apply for all valid processor bus and L2 bus ratios. The values do not include I/O supply
power (OVDD and L2OVDD) or PLL/DLL supply power (AVDD and L2AVDD). OVDD and L2OVDD power is
system dependent, but is typically <5% of VDD power. Worst case power consumption for AVDD = 15
mW and L2AVDD = 15 mW.
2. Maximum power is measured at 105°C, at VDD = 1.8V or 1.5Vwhile running an entirely cache-resident,
contrived sequence of instructions which keep the execution units, including AltiVec, maximally busy.
3. Typical power is an average value measured at 65°C, VDD = 1.8V or 1.5V,
OVDD = L2OVDD = 2.5V in a system while running a codec application that is AltiVec intensive.
4. These values include the use of AltiVec. Without AltiVec operation, estimate a 25% decrease.
5. Power consumption derating at low temperatures to be defined after device characterization.
18
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
9. Electrical Characteristics
9.1
Static Characteristics
Table 9-1.
DC Electrical Specifications (see Table 6-3 on page 11 for Recommended Operating Conditions)
Nominal Bus
Voltage(1)
Min
Max
1.8
0.65 x (L2)OVDD
(L2)OVDD + 0.2
2.5
1.7
(L2)OVDD + 0.2
3.3
2.0
OVDD + 0.3
1.8
-0.3
0.35 x (L2)OVDD
2.5
-0.3
0.2 x (L2)OVDD
3.3
-0.3
0.8
1.8
1.5
OVDD + 0.2
2.5
2.0
OVDD + 0.2
CVIH
3.3
2.4
OVDD + 0.3
CVIL
1.8
-0.3
0.2
2.5
-0.3
0.4
3.3
-0.3
0.4
1.8
–
20
2.5
–
35
3.3
–
70
1.8
–
20
2.5
–
35
3.3
–
70
1.8
(L2)OVDD - 0.45
–
2.5
1.7
–
VOH
3.3
2.4
–
VOL
1.8
–
0.45
2.5
–
0.4
3.3
–
0.4
–
6.0
Symbol
Characteristic
VIH
VIH
Input high voltage
(all inputs except SYSCLK)(2)(3)(8)
VIH
VIL
VIL
Input low voltage
(all inputs except SYSCLK)(8)
VIL
CVIH
CVIH
CVIL
(2)(8)
SYSCLK input high voltage
SYSCLK input low voltage(8)
CVIL
IIN
IIN
Input leakage current,
VIN = L2OVDD/OVDD(2)(3)(6)(7)
IIN
ITSI
ITSI
High-Z (off-state) leakage current,
VIN = L2OVDD/OVDD(2)(3)(5)(7)
ITSI
VOH
VOH
VOL
Output high voltage, IOH = -5 mA
(8)
Output low voltage, IOL = 5 mA(8)
VOL
CIN
Note:
Capacitance, VIN = 0V, f = 1 MHz
(3)(4)(7)
Unit
V
V
V
V
µA
µA
V
V
pF
1. Nominal voltages; see Table 6-3 on page 11 for recommended operating conditions.
2. For processor bus signals, the reference is OVDD while L2OVDD is the reference for the L2 bus signals.
3. Excludes factory test signals.
4. Capacitance is periodically sampled rather than 100% tested.
5. The leakage is measured for nominal OVDD and L2OVDD, or both OVDD and L2OVDD must vary in the same direction (for
example, both OVDD and L2OVDD vary by either +5% or -5%).
6. Measured at max OVDD/L2OVDD.
7. Excludes IEEE 1149.1 boundary scan (JTAG) signals.
19
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
8. For JTAG support: all signals controlled by BVSEL and L2VSEL will see VIL/VIH/VOL/VOH/CVIH/CVIL DC limits of 1.8V mode
while either the EXTEST or CLAMP instruction is loaded into the IEEE 1149.1 instruction register by the UpdateIR TAP state
until a different instruction is loaded into the instruction register by either another UpdateIR or a Test-Logic-Reset TAP state.
If only TSRT is asserted to the part, and then a SAMPLE instruction is executed, there is no way to control or predict what
the DC voltage limits are. If HRESET is asserted before executing a SAMPLE instruction, the DC voltage limits will be controlled by the BVSEL/L2VSEL settings during HRESET. Anytime HRESET is not asserted (i.e., just asserting TRST), the
voltage mode is not known until either EXTEST or CLAMP is executed, at which time the voltage level will be at the DC limits
of 1.8V.
9.2
Dynamic Characteristics
After fabrication, parts are sorted by maximum processor core frequency as shown in “Clock AC Specifications” and tested for conformance to the AC specifications for that frequency. These specifications are
for valid processor core frequencies. The processor core frequency is determined by the bus (SYSCLK)
frequency and the settings of the PLL_CFG[0:3] signals. Parts are sold by maximum processor core
frequency.
9.2.1
Clock AC Specifications
Table 9-2 provides the clock AC timing specifications as defined in Figure 9-1 on page 21.
Table 9-2.
Clock AC Timing Specifications (See Table 6-3 on page 11 for Recommended Operating Conditions)
Maximum Processor Core Frequency
400 MHz
450 MHz
500 MHz
Symbol
Characteristic
Min
Max
Min
Max
Min
Max
Unit
fCORE(1)
Processor frequency
350
400
350
450
350
500
MHz
VCO frequency
700
800
700
900
700
1000
MHz
fSYSCLK(1)
SYSCLK frequency
33
133
33
133
33
133
MHz
tSYSCLK
SYSCLK cycle time
7.5
30
7.5
30
7.5
30
ns
fVCO
(1)
tKR &
tKF(2)
tKR &
tKF(3)
tKHKL/tSYSCLK(4)
SYSCLK duty cycle measured at OVDD/2
SYSCLK jitter
(5)
Internal PLL relock time
Note:
1.0
1.0
1
ns
0.5
0.5
0.5
ns
60
%
SYSCLK rise and fall time
(6)
40
60
40
60
40
±150
±150
±150
ps
100
100
100
µs
1. Caution: The SYSCLK frequency and PLL_CFG[0:3] settings must be chosen such that the resulting SYSCLK (bus) frequency, CPU (core) frequency and PLL (VCO) frequency do not exceed their respective maximum or minimum operating
frequencies. Refer to the PLL_CFG[0:3] signal description in “Clock Selection” on page 42 for valid PLL_CFG[0:3] settings.
2. Rise and fall times for the SYSCLK input measured from 0.4V to 2.4V when OVDD = 3.3V nominal.
3. Rise and fall times for the SYSCLK input measured from 0.2V to 1.2V when OVDD = 1.8V or 2.5V nominal.
4. Timing is guaranteed by design and characterization.
5. This represents total input jitter, short-term and long-term combined, and is guaranteed by design.
6. Relock timing is guaranteed by design and characterization. PLL-relock time is the maximum amount of time required for
PLL lock after a stable VDD and SYSCLK are reached during the power-on reset sequence. This specification also applies
when the PLL has been disabled and subsequently re-enabled during sleep mode. Also note that HRESET must be held
asserted for a minimum of 255 bus clocks after the PLL-relock time during the power-on reset sequence.
20
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 9-1.
SYSCLK Input Timing Diagram
tKR
tSYSCLK
tKF
tKHKL
CVIH
SYSCLK
VM
Note:
9.2.2
VM
VM
CVIL
VM = Midpoint Voltage (OVDD/2).
Processor Bus AC Specifications
Table 9-3 provides the processor AC timing specifications for the PC7410 as defined in Figure 9-3 on
page 23 and Figure 9-4 on page 24. Timing specifications for the L2 bus are provided in “L2 Bus AC
Specifications” on page 26.
Table 9-3.
Processor Bus AC Timing Specifications(1) at VDD = AVDD = 1.8V ± 100 mV;
-55°C ≤TJ ≤125°C, OVDD = 1.8V ± 100 mV
400, 450, 500 MHz
Symbol
(2)
Parameter
Min
Max
Unit
tIVKH
Input Setup
1.0
–
ns
tIXKH
Input Hold
0
–
ns
–
–
–
3.0
2.3
3.0
(7)(8)
tKHTSV
tKHARV
tKHOV
Output Valid Times:
TS
ARTRY/SHD0/SHD1
All Other Outputs
tKHTSX
tKHARX
tKHOX
Output Hold Times:(7)(12)
TS
ARTRY/SHD0/SHD1
All Other Outputs
0.5
0.5
0.5
–
–
–
tKHOE(11)
SYSCLK to Output Enable
0.5
–
ns
tKHOZ
SYSCLK to Output High Impedance (all except ABB/AMON[0], ARTRY/SHD,
DBB/DMON[0]), SHD0, SHD1)
–
3.5
ns
tKHABPZ(5)(9)(11)
SYSCLK to ABB/AMON[0], DBB/DMON[0] High Impedance after precharge
–
1
tSYSCLK
tKHARP(5)(10)(11)
Maximum Delay to ARTRY/SHD0/SHD1 Precharge
–
1
tSYSCLK
Note:
ns
ns
1. All input specifications are measured from the midpoint of the signal in question to the midpoint of the rising edge of the input
SYSCLK. All output specifications are measured from the midpoint of the rising edge of SYSCLK to the midpoint of the signal in question. All output timings assume a purely resistive 50Ω load (see Figure 9-3 on page 23). Input and output timings
are measured at the pin; time-of-flight delays must be added for trace lengths, vias and connectors in the system.
2. The symbology used for timing specifications herein follows the pattern of
t(signal)(state)(reference)(state) for inputs and t(reference)(state)(signal)(state) for outputs. For example, tIVKH symbolizes the time input signals
(I) reach the valid state (V) relative to the SYSCLK reference (K) going to the high (H) state or input setup time. And tKHOV
symbolizes the time from SYSCLK (K) going high (H) until outputs (O) are valid (V) or output valid time. Input hold time can
be read as the time that the input signal (I) went invalid (X) with respect to the rising clock edge (KH) - note the position of
the reference and its state for inputs -and output hold time can be read as the time from the rising edge (KH) until the output
went invalid (OX).
3. The setup and hold time is with respect to the rising edge of HRESET (see Figure 9-4 on page 24).
21
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
4. This specification is for configuration mode select only. Also note that the HRESET must be held asserted for a minimum of
255 bus clocks after the PLL re-lock time during the power-on reset sequence.
5. tSYSCLK is the period of the external clock (SYSCLK) in nanoseconds(ns). The numbers given in the table must be multiplied
by the period of SYSCLK to compute the actual time duration (in nanoseconds) of the parameter in question.
6. Mode select signals are BVSEL, EMODE, L2VSEL, PLL_CFG[0:3].
7. All other output signals are composed of the following - A[0:31], AP[0:3], TT[0:4], TBST, TSIZ[0:2], GBL, WT, CI, DH[0:31],
DL[0:31], DP[0:7], BR, CKSTP_OUT, DRDY, HIT, QREQ, RSRV.
8. Output valid time is measured from 2.4V to 0.8V which may be longer than the time required to discharge from VDD to 0.8V.
9. According to the 60x bus protocol, ABB and DBB are driven only by the currently active bus master. They are asserted low
then precharged high before returning to high-Z as shown in Figure 9-2 on page 23. The nominal precharge width for ABB or
DBB is 0.5 x tSYSCLK, i.e., less than the minimum tSYSCLK period, to ensure that another master asserting ABB, or DBB on the
following clock will not contend with the precharge. Output valid and output hold timing is tested for the signal asserted. Output valid time is tested for precharge.The high-Z behavior is guaranteed by design.
10. According to the 60x bus protocol, ARTRY can be driven by multiple bus masters through the clock period immediately following AACK. Bus contention is not an issue since any master asserting ARTRY will be driving it low. Any master asserting
it low in the first clock following AACK will then go to high-Z for one clock before precharging it high during the second cycle
after the assertion of AACK. The nominal precharge width for ARTRY is 1.0 tSYSCLK ; i.e., it should be high-Z as shown in Figure 9-2 on page 23 before the first opportunity for another master to assert ARTRY. Output valid and output hold timing are
tested for the signal asserted. Output valid time is tested for precharge. The high-Z behavior is guaranteed by design.
11. Guaranteed by design and not tested.
12. Output hold time characteristics can be altered by the use of the L2_TSTCK pin during system reset, similar to L2 output
hold being altered by the use of bits [14-15] in the L2CR register. Information on the operation of the L2_TSTCLK will be
included in future revisions of this specification.
22
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 9-2.
Input/Output Timing Diagram
VM
VM
VM
SYSCLK
tIVKH
tIXKH
All Inputs
All Outputs
(except TS, ABB,
ARTRY, DBB)
All Outputs
(except TS, ABB,
ARTRY, DBB)
tKHOX
tKHOV
tKHOE
tKHOZ
tKHABPZ
TS,
ABB/AMON[0],
DBB/DMON[0]
tKHTSV
tKHTSV
tKHTSX
tKHARPZ
tKHARP
ARTRY,
tKHARV
SHD0,
SHD1
tKHARV
tKHARX
VM = Midpont Voltage (OVDD/2)
Figure 9-3.
AC Test Load for the 60x Interface
Output
OVDD/2
Z0 = 50Ω
RL = 50Ω
Figure 9-4 on page 24 provides the mode select input timing diagram for the PC7410. The mode select
inputs are sampled twice, once before and once after HRESET negation.
23
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 9-4.
Mode Input Timing Diagram
SYSCLK
VM
VM
HRESET
Mode Signals
First sample
Second sample
where VM = Midpoint Voltage (OVDD/2)
9.2.3
L2 Clock AC Specifications
The L2CLK frequency is programmed by the L2 configuration register (L2CR[4:6]) core-to-L2 divisor
ratio. See Table 13-2 on page 43 for example core and L2 frequencies at various divisors. Table 9-4 on
page 25 provides the potential range of L2CLK output AC timing specifications as defined in Figure 9-5
on page 26.
The L2SYNC_OUT signal is intended to be routed halfway out to the SRAMs and then returned to the
L2SYNC_IN input of the PC7410 to synchronize L2CLKOUT at the SRAM with the processor’s internal
clock. L2CLKOUT at the SRAM can be offset forward or backward in time by shortening or lengthening
the routing of L2SYNC_OUT to L2SYNC_IN. See Freescale™ Application Note AN179/D "PowerPC
Backside L2 Timing Analysis for the PCB Design Engineer."
The minimum L2CLK frequency of Table 9-4 is specified by the maximum delay of the internal DLL. The
variable-tap DLL introduces up to a full clock period delay in the L2CLKOUTA, L2CLKOUTB and
L2SYNC_OUT signals so that the returning L2SYNC_IN signal is phase aligned with the next core clock
(divided by the L2 divisor ratio). Do not choose a core-to-L2 divisor which results in an L2 frequency
below this minimum, or the L2CLKOUT signals provided for SRAM clocking will not be phase aligned
with the PC7410 core clock at the SRAMs.
The maximum L2CLK frequency shown in Table 9-4 is the core frequency divided by one. Very few L2
SRAM designs will be able to operate in this mode. Most designs will select a greater core-to-L2 divisor
to provide a longer L2CLK period for read and write access to the L2 SRAMs. The maximum L2CLK frequency for any application of the PC7410 will be a function of the AC timings of the PC7410, the AC
timings for the SRAM, bus loading and printed circuit board trace length.
e2v is similarly limited by system constraints and cannot perform tests of the L2 interface on a socketed
part on a functional tester at the maximum frequencies of Table 9-4. Therefore, functional operation and
AC timing information are tested at core-to-L2 divisors of 2 or greater.
L2 input and output signals are latched or enabled respectively by the internal L2CLK (which is SYSCLK
multiplied up to the core frequency and divided down to the L2CLK frequency). In other words, the AC
timings of Table 9-5 on page 26 are entirely independent of L2SYNC_IN. In a closed loop system, where
L2SYNC_IN is driven through the board trace by L2SYNC_OUT, L2SYNC_IN only controls the output
phase of L2CLKOUTA and L2CLKOUTB which are used to latch or enable data at the SRAMs. However, since in a closed loop system L2SYNC_IN is held in phase alignment with the internal L2CLK, the
signals of Table 9-5 are referenced to this signal rather than the not-externally-visible internal L2CLK.
During manufacturing test, these times are actually measured relative to SYSCLK.
24
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Table 9-4.
L2CLK Output AC Timing Specifications at Recommended Operating Conditions (See Table 6-3 on page
11)
400 MHz
450 MHz
500 MHz
Symbol
Parameter
Min
Max
Min
Max
Min
Max
Unit
fL2CLK(1)(4)
L2CLK frequency
133
400
133
400
133
400
MHz
tL2CLK
L2CLK cycle time
2.5
7.5
2.5
7.5
2.5
7.5
ns
tCHCL/tL2CLK(2)
L2CLK duty cycle
50
(3)
Internal DLL-relock time
tL2CSKW
Note:
50
640
50
640
%
640
-
L2CLK
DLL capture window(5)
0
10
0
10
0
10
ns
L2CLKOUT output-to-output
skew(6)
-
50
-
50
-
50
ps
L2CLKOUT output jitter(6)
-
±150
-
±150
-
±150
ps
1. L2CLK outputs are L2CLK_OUTA, L2CLK_OUTB, and L2SYNC_OUT pins. The L2CLK frequency to core frequency settings must be chosen such that the resulting L2CLK frequency and core frequency do not exceed their respective maximum
or minimum operating frequencies. The maximum L2LCK frequency will be system-dependent. L2CLK_OUTA and
L2CLK_OUTB must have equal loading.
2. The nominal duty cycle of the L2CLK is 50% measured at midpoint voltage.
3. The DLL re-lock time is specified in terms of L2CLKs. The number in the table must be multiplied by the period of L2CLK to
compute the actual time duration in nanoseconds. Re-lock timing is guaranteed by design and characterization.
4. The L2CR[L2SL] bit should be set for L2CLK frequencies less than 110 MHz. This adds more delay to each tap of the DLL.
5. Allowable skew between L2SYNC_OUT and L2SYNC_IN.
6. Guaranteed by design and not tested. This output jitter number represents the maximum delay of one tap forward or one tap
back from the current DLL tap as the phase comparator seeks to minimize the phase difference between L2SYNC_IN and
the internal L2CLK. This number must be comprehended in the L2 timing analysis. The input jitter on SYSCLK affects
L2CLKOUT and the L2 address/data/control signals equally and therefore is already comprehended in the AC timing and
does not have to be considered in the L2 timing analysis.
25
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 9-5.
L2CLK_OUT Output Timing Diagram
L2 Single-Ended Clock Mode
tL2CLK
tCHCL
tL2CR
L2CLK_OUTA
VM
VM
VM
L2CLK_OUTB
VM
VM
VM
tL2CF
tL2CSKW
L2SYNC_OUT
VM
VM
L2 Differential Clock Mode
VM
VM
tL2CLK
tCHCL
L2CLK_OUTB
L2CLK_OUTA
VM
VM
VM
L2SYNC_OUT
VM
VM
VM
Note:
9.2.4
VM = Midpoint Voltage (L2OVDD/2)
L2 Bus AC Specifications
Table 9-5 provides the L2 bus interface AC timing specifications for the PC7410 as defined in Figure 9-6
on page 27 and Figure 9-7 on page 28 for the loading conditions described in Figure 9-8 on page 28.
Table 9-5.
L2 Bus Interface AC Timing Specifications at VDD = AVDD = L2AVDD = 1.8V ± 100mV or 1.5V ± 50mV ;
-55°C ≤TJ ≤125°C, L2OVDD = 2.5V ± 100mV or L2OVDD = 1.8V ± 100mV
400, 450, 500 MHz
Symbol
Parameter
tL2CR & tL2CF(1)
L2SYNC_IN rise and fall time
tDVL2CH(2)
Setup Times
Data and parity
tDXL2CH(2)
Input Hold Times
Data and parity
Min
Max
Unit
1.0
ns
ns
1.5
0.0
ns
26
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Table 9-5.
L2 Bus Interface AC Timing Specifications at VDD = AVDD = L2AVDD = 1.8V ± 100mV or 1.5V ± 50mV ;
-55°C ≤TJ ≤125°C, L2OVDD = 2.5V ± 100mV or L2OVDD = 1.8V ± 100mV (Continued)
400, 450, 500 MHz
Symbol
(3)(4)
Valid Times
All outputs when L2CR[14:15] = 00
All outputs when L2CR[14:15] = 01
All outputs when L2CR[14:15] = 10
All outputs when L2CR[14:15] = 11
(3)
Output Hold Times
All outputs when L2CR[14:15] = 00
All outputs when L2CR[14:15] = 01
All outputs when L2CR[14:15] = 10
All outputs when L2CR[14:15] = 11
tL2CHOV
tL2CHOX
Parameter
Max
Unit
2.5
2.5
2.9
3.5
ns
0.4
0.8
1.2
1.6
L2SYNC_IN to high impedance
All outputs when L2CR[14:15] = 00
All outputs when L2CR[14:15] = 01
All outputs when L2CR[14:15] = 10
All outputs when L2CR[14:15] = 11
tL2CHOZ
Note:
Min
ns
2.0
2.5
3.0
3.5
ns
1. Rise and fall times for the L2SYNC_IN input are measured from 20% to 80% of L2OVDD.
2. All input specifications are measured from the midpoint of the signal in question to the midpoint voltage of the rising edge of
the input L2SYNC_IN (see Figure 9-6). Input timings are measured at the pins.
3. All output specifications are measured from the midpoint voltage of the rising edge of L2SYNC_IN to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50Ω load (see
Figure 9-8 on page 28).
4. The outputs are valid for both single-ended and differential L2CLK modes. For pipelined registered synchronous burst
RAMs, L2CR[14:15] = 00 is recommended. For pipelined late-write synchronous burst SRAMs, L2CR[14:15] = 10 is
recommended.
Figure 9-6.
L2 Bus Input Timing Diagram
tL2CR
tL2CF
VM
L2SYNC_IN
tDVL2CH
tDXL2CH
L2 Data and Data
Parity Inputs
Note:
VM = Midpoint Voltage (L2OVDD/2)
27
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 9-7.
L2 Bus Output Timing Diagram
VM
VM
L2SYNC_IN
tL2CHOV
tL2CHOX
All Outputs
tL2CHOZ
L2DATA BUS
Note:
VM = Midpoint Voltage (L2OVDD/2)
Figure 9-8.
AC Test Load for the L2 Interface
Output
L2OVDD/2
Z0 = 50Ω
RL = 50Ω
9.2.5
IEEE 1149.1 AC Timing Specifications
Table 9-6 provides the IEEE® 1149.1 (JTAG) AC timing specifications as defined in Figure 9-9 on page
29, Figure 9-10 on page 29, Figure 9-11 on page 29 and Figure 9-12 on page 30.
Table 9-6.
JTAG AC Timing Specifications (Independent of SYSCLK) (1)at Recommended Operating
Conditions (see Table 6-3 on page 11)
Symbol
Parameter
Min
Max
Unit
fTCLK
TCK frequency of operation
0
33.3
MHz
t TCLK
TCK cycle time
30
ns
tJHJL
TCK clock pulse width measured at OVDD/2
15
ns
tJR & tJF
TCK rise and fall times
0
tTRST(2)
TRST assert time
25
ns
tDVJH(3)
tIVJH
Input Setup Times:
Boundary-scan data
TMS, TDI
4
0
ns
tDXJH(3)
tIXJH
Input Hold Times:
Boundary-scan data
TMS, TDI
20
25
ns
4
4
20
25
ns
tJLOV
Valid Times:
Boundary-scan data
TDO
tJLDZ(4)(5)
tJLOZ(5)
TCK to output high impedance:
Boundary-scan data
TDO
3
3
19
9
ns
tJLDV(4)
2
ns
28
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Notes:
1. All outputs are measured from the midpoint voltage of the falling/rising edge of TCLK to the midpoint of
the signal in question. The output timings are measured at the pins. All output timings assume a purely
resistive 50 Ω load (see Figure 9-9). Time-of-flight delays must be added for trace lengths, vias and connectors in the system.
2. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only.
3. Non-JTAG signal input timing with respect to TCK.
4. Non-JTAG signal output timing with respect to TCK.
5. Guaranteed by design and characterization.
Figure 9-9.
Alternate AC Test Load for the JTAG Interface
Output
OVDD/2
Z0 = 50Ω
RL = 50Ω
Figure 9-10. JTAG Clock Input Timing Diagram
tJR
TCLK
VM
VM
tJF
VM
tJHJL
tTCLK
Note:
VM = Midpoint Voltage (OVDD/2)
Figure 9-11. TRST Timing Diagram
tTRST
VM
TRST
Note:
VM
VM = Midpoint Voltage (OVDD/2)
29
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 9-12. Boundary-scan Timing Diagram
TCK
VM
VM
tDVJH
Boundary
Data Inputs
tDXJH
Input Data
Valid
tJLDV
tJLDX
Boundary
Data Outputs
Output Data Valid
tJLDZ
Boundary
Data Outputs
Note:
Output Data Valid
VM = Midpoint Voltage (OVDD/2)
Figure 9-13. Test Access Port Timing Diagram
TCK
VM
VM
tIVJH
TDI, TMS
tIXJH
Input Data
Valid
tJLOV
tJLOX
TDO
Output Data Valid
tJLOZ
TDO
Note:
Output Data Valid
VM = Midpoint Voltage (OVDD/2)
30
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
10. Preparation for Delivery
10.1
Handling
MOS devices must be handled with certain precautions to avoid damage due to accumulation of static
charge. Input protection devices have been designed in the chip to minimize the effect of static buildup.
However, the following handling practices are recommended:
• Devices should be handled on benches with conductive and grounded surfaces
• Ground test equipment, tools and operator
• Do not handle devices by the leads
• Store devices in conductive foam or carriers
• Avoid use of plastic, rubber or silk in MOS areas
• Maintain relative humidity above 50% if practical
• For CI-CGA packages, use specific tray to take care of the highest height of the package compared
with the normal CBGA
11. Package Mechanical Data
11.1
Parameters
The package parameters are as provided in the following list. The package type is 25x25 mm, 360-lead
CBGA, HiTCE and CI-CGA.
Table 11-1.
Package Parameters
Parameter
Package outline
25 mm x 25 mm
Interconnects
360 (19 x 19 ball array minus one)
Pitch
1.27 mm (50 mil)
Minimum module height
2.65 mm (CBGA, HiTCE), 3.65 mm (CI-CGA)
Maximum module height
3.20 mm (CBGA), 3.24 mm (HiTCE), 4.20 mm (CI-CGA)
Ball or column diameter
0.89 mm (35 mil)
The following remarks apply to Figure 12-7 on page 39 and Figure 12-9 on page 41:
• Dimensions and tolerancing are as per ASME Y14.5M-1994.
• All dimensions are in millimeters.
• Top side A1 corner index is a metallized feature with various shapes. Bottom side A1 corner is
designated with a ball missing from the array.
• Dimension B is the maximum solder ball diameter measured parallel to datum A.
• D2 and E2 define the area occupied by the die and underfill. Actual size of this area may be smaller
than shown. D3 and E3 are the minimum clearance from the package edge to the chip capacitors.
31
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
12. Pin Assignments
12.1
BGA360 Package
Figure 12-1, Figure 12-2, Figure 12-3 on page 33 and Figure 12-4 on page 33 show top views of the
packages available for the PC7410. Note that these drawings are not to scale.
Figure 12-1. Top View of 360-Ball CBGA and 360-Pin CI-CGA Packages
Pin A1 Index
Figure 12-2. Top View of 360-pin CBGA and CI-CGA Packages
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
32
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 12-3. Cross-section of 360-ball CBGA and HiTCE Package
Substrate Assembly
View
Die
Encapsulant
Figure 12-4. Cross-section of 360-column CI-CGA Package
Substrate Assembly
View
Die
Encapsulant
Table 12-1.
Pinout Listing for the PC7410, 360-ball CBGA and CI-CGA packages
Active
I/O
I/F Select(1)
A13, D2, H11, C1, B13, F2, C13, E5, D13, G7, F12, G3, G6,
H2, E2, L3, G5, L4, G4, J4, H7, E1, G2, F3, J7, M3, H3, J2,
J6, K3, K2, L2
High
I/O
BVSEL
N3
Low
Input
BVSEL
ABB
AMON[0](12)
L7
Low
Output
BVSEL
AP[0:3]
C4, C5, C6, C7
High
I/O
BVSEL
ARTRY
L6
Low
I/O
BVSEL
AVDD
A8
BG
H1
Low
Input
BVSEL
BR
E7
Low
Output
BVSEL
W1
High
Input
N/A
CHK
K11
Low
Input
BVSEL
CI
C2
Low
I/O
BVSEL
CKSTP_IN
B8
Low
Input
BVSEL
CKSTP_OUT
D7
Low
Output
BVSEL
CLK_OUT
E3
High
Output
BVSEL
DBB
DMON[0](12)
K5
Low
Output
BVSEL
DBG
K1
Low
Input
BVSEL
Signal Name
Pin Number
A[0:31]
AACK
(12)
BVSEL(1)(3)(8)(9)(14)
(4)(8)(9)
VDD
(12)
33
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Table 12-1.
Pinout Listing for the PC7410, 360-ball CBGA and CI-CGA packages (Continued)
Active
I/O
I/F Select(1)
W12, W11, V11, T9, W10, U9, U10, M11, M9, P8, W7, P9,
W9, R10, W6, V7, V6, U8, V9, T7, U7, R7, U6, W5, U5, W4,
P7, V5, V4, W3, U4, R5
High
I/O
BVSEL
DL[0:31]
M6, P3, N4, N5, R3, M7, T2, N6, U2, N7, P11, V13, U12,
P12, T13, W13, U13, V10, W8, T11, U11, V12, V8, T1, P1,
V1, U1, N1, R2, V3, U3, W2
High
I/O
BVSEL
DP[0:7]
L1, P2, M2, V2, M1, N2, T3, R1
High
I/O
BVSEL
DRDY(6)(8)(13)
K9
Low
Output
BVSEL
DBWO
DTI[0]
D1
Low
Input
BVSEL
DTI[1:2](10)(13)
H6, G1
High
Input
BVSEL
EMODE(7)(10)
A3
Low
Input
BVSEL
GBL
B1
Low
I/O
BVSEL
GND
D10, D14, D16, D4, D6, E12, E8, F4, F6, F10, F14, F16, G9,
G11, H5, H8, H10, H12, H15, J9, J11, K4, K6, K8, K10, K12,
K14, K16, L9, L11, M5, M8, M10, M12, M15, N9, N11, P4,
P6, P10, P14, P16, R8, R12, T4, T6, T10, T14, T16
HIT(6)(8)
B5
Low
Output
BVSEL
HRESET
B6
Low
Input
BVSEL
C11
Low
Input
BVSEL
F8
High
Input
BVSEL
L2ADDR[0:16]
L17, L18, L19, M19, K18, K17, K15, J19, J18, J17, J16, H18,
H17, J14, J13, H19, G18
High
Output
L2VSEL
L2ADDR[17:18](8)
K19, W19
High
Output
L2VSEL
L2AVDD
L13
L2CE
P17
Low
Output
L2VSEL
L2CLKOUTA
N15
High
Output
L2VSEL
L2CLKOUTB
L16
High
Output
L2VSEL
L2DATA[0:63]
U14, R13, W14, W15, V15, U15, W16, V16, W17, V17, U17,
W18, V18, U18, V19, U19, T18, T17, R19, R18, R17, R15,
P19, P18, P13, N14, N13, N19, N17, M17, M13, M18, H13,
G19, G16, G15, G14, G13, F19, F18, F13, E19, E18, E17,
E15, D19, D18, D17, C18, C17, B19, B18, B17, A18, A17,
A16, B16, C16, A14, A15, C15, B14, C14, E13
High
I/O
L2VSEL
L2DP[0:7]
V14, U16, T19, N18, H14, F17, C19, B15
High
I/O
L2VSEL
L2OVDD(11)
D15, E14, E16, H16, J15, L15, M16, K13, P15, R14, R16,
T15, F15
L2SYNC_IN
L14
High
Input
L2VSEL
L2SYNC_OUT
M14
High
Output
L2VSEL
L2_TSTCLK(2)
F7
High
Input
BVSEL
A19
High
Input
N/A
Signal Name
Pin Number
DH[0:31]
INT
L1_TSTCLK
L2VSEL
(2)
(1)(3)(8)(9)(14)
N/A
VDD
N/A
34
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Table 12-1.
Pinout Listing for the PC7410, 360-ball CBGA and CI-CGA packages (Continued)
Active
I/O
I/F Select(1)
N16
Low
Output
L2VSEL
G17
High
Output
L2VSEL
F9
Low
Input
BVSEL
MCP
B11
Low
Input
BVSEL
OVDD
D5, D8, D12, E4, E6, E9, E11, F5, H4, J5, L5, M4, P5, R4,
R6, R9, R11, T5, T8, T12
PLL_CFG[0:3]
A4, A5, A6, A7
High
Input
BVSEL
QACK
B2
Low
Input
BVSEL
QREQ
J3
Low
Output
BVSEL
RSRV
D3
Low
Output
BVSEL
SHD0(8)
B3
Low
I/O
BVSEL
SHD1
B4
Low
I/O
BVSEL
SMI
A12
Low
Input
BVSEL
SRESET
E10
Low
Input
BVSEL
SYSCLK
H9
Input
BVSEL
TA
F1
Low
Input
BVSEL
TBEN
A2
High
Input
BVSEL
TBST
A11
Low
Output
BVSEL
TCK
B10
High
Input
BVSEL
TDI
B7
High
Input
BVSEL
TDO
D9
High
Output
BVSEL
TEA
J1
Low
Input
BVSEL
C8
High
Input
BVSEL
TRST
A10
Low
Input
BVSEL
TS
K7
Low
I/O
BVSEL
TSIZ[0:2]
A9, B9, C9
High
Output
BVSEL
TT[0:4]
C10, D11, B12, C12, F11
High
I/O
BVSEL
WT
C3
Low
I/O
BVSEL
VDD
G8, G10, G12, J8, J10, J12, L8, L10, L12, N8, N10, N12
Signal Name
Pin Number
L2WE
L2ZZ
LSSD_MODE
(5)(8)
(9)
TMS(9)
(9)(14)
Notes:
(2)
N/A
N/A
1. OVDD supplies power to the processor bus, JTAG and all control signals except the L2 cache controls (L2CE, L2WE, and
L2ZZ); L2OVDD supplies power to the L2 cache interface (L2ADDR[0:18], L2ASPARE, L2DATA[0:63], L2DP[0:7] and
L2SYNC_OUT) and the L2 control signals and VDD supplies power to the processor core and the PLL and DLL (after filtering
to become AVDD and L2AVDD respectively). These columns serve as a reference for the nominal voltage supported on a
given signal as selected by the BVSEL/L2VSEL pin configurations of Table 6-2 on page 10 and the voltage supplied. For
actual recommended value of VIN or supply voltages, see Table 6-3 on page 11.
2. These are test signals for factory use only and must be pulled up to OVDD for normal machine operation.
35
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
3. To allow for future I/O voltage changes, provide the option to connect BVSEL and L2VSEL independently to either OVDD
(selects 2.5V), GND (selects 1.8V), or to HRESET (selects 2.5V). The PC7410 Both the 60x processor bus and the L2 bus
only support the 1.8 and 2.5 options (see Table 6-2 on page 10). the default selection if BVSEL and/or L2VSEL is left unconnected is 2.5V.
4. Connect to HRESET to trigger post power-on-reset (por) internal memory test.
5. Ignored in 60x bus mode.
6. Unused output in 60x bus mode.
7. Deasserted (pulled high) at HRESET for 60x bus mode.
8. Uses one of 9 existing no-connects in PC750’s 360-ball BGA package.
9. Internal pull-up on die.
10. Reuses PC750’s DRTRY, DBDIS and TLBISYNC pins (DTI1, DTI2 and EMODE respectively).
11. The VOLTDET pin position on the PC750 360-ball CBGA package is now an L2OVDD pin on the PC7410 packages.
12. Output only for PC7410, was I/O for PC750.
13. Enhanced mode only.
14. To overcome the internal pull-up resistance and ensure this input will recognize a low signal, a pull-down resistance less
than 250Ω should be used.
36
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 12-5. Mechanical Dimensions and Bottom Surface Nomenclature of the 360-ball CBGA Package
2X
0.2
A
D
A1 CORNER
D2
D3
Millimeters
C6-2
C6-1
C5-1
C5-2
C1-1 12X
J2
C1-2
C
0.15 A
0.25 A
E
E2
E3
C4-1
C4-2
0.35 A
L2 L1
2X
0.2
12X
12X J3 C3-1
C3-2
J1
C2-2
C2-1
K2
K1
B
1 2 3 4 5 6 7 8 9 10 11 1213141516 171819
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
DIM
A
A1
A2
A3
A4
b
D
D2
D3
e
E
E2
E3
J1
J2
J3
K1
K2
L1
L2
MIN
2,72
0,8
1,1
MAX
3,2
1
1,3
0,6
0,82
0,9
0,82
0,93
25 BSC
10 typ
6,32
1,27 BSC
25 BSC
12,6 typ
8,26
0,89 BSC
3,2 BSC
0,68 BSC
6,56
8,13
8,61
7,04
A3
A2
A4
Package
Caps
A1
C1-1
A
C1-2
Value
µF
0.01
C2-1
e
360X
B
0.3
C A B
0.15 C
C2-2
0.01
C3-1
C3-2
0.01
C4-1
C4-2
0.01
C5-1
C5-2
0.01
C6-1
C6-2
Notes:
0.01
Voltage
Reference
L2OVDD
GND
L2OVDD
GND
VDD
GND
OVDD
GND
OVDD
GND
VDD
GND
1. Dimensioning and tolerancing per ASME Y14.5M, 1994
2. Dimensions in millimeters
3. Top side A1 corner index is a metallized feature with various shapes. Bottom side A1 corner is designated with a ball missing
from the array
37
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
12.2
Substrate Capacitors for the PC7410
Figure 12-6 shows the connectivity of the substrate capacitor pads for the PC7410, 360 CBGA package.
Figure 12-6. Substrate Bypass Capacitors for the PC7410
A1 CORNER
C6-2
C6-1
C5-1
C5-2
Package Caps
C1-1
C1-2
C1-1
C1-2
C2-1
C2-2
C3-1
C4-1
C4-2
C3-2
L2 L1
Value µF Voltage Reference
0.01
0.01
VDD
GND
0.01
OVDD
GND
0.01
OVDD
GND
0.01
VDD
GND
C5-1
C2-2
C2-1
C3-1
C3-2
C5-2
C6-1
C6-2
L2OVDD
GND
0.01
C4-1
C4-2
L2OVDD
GND
38
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 12-7. Mechanical Dimensions and Bottom Surface Nomenclature of the 360-ball HiTCE Package
2X
0.2
A
D
A1 CORNER
D2
D3
Millimeters
C6-2
C6-1
C5-1
C5-2
C1-1 12X
J2
C1-2
C
0.15 A
0.25 A
E
E2
C4-1
E3
C4-2
0.35 A
L2 L1
2X
0.2
12X
12X J3 C3-1
C3-2
J1
C2-2
C2-1
K2
K1
B
1 2 3 4 5 6 7 8 9 10 11 1213141516 171819
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
DIM
A
A1
A2
A3
A4
b
D
D2
D3
e
E
E2
E3
J1
J2
J3
K1
K2
L1
L2
MIN
2,72
0,8
1,1
MAX
3,2
1
1,3
0,6
0,82
0,9
0,82
0,93
25 BSC
10 typ
6,32
1,27 BSC
25 BSC
12,6 typ
8,26
0,89 BSC
3,2 BSC
0,68 BSC
6,56
8,13
8,61
7,04
A3
A2
A4
Package
Caps
A1
C1-1
A
C1-2
Value
µF
0.01
C2-1
e
360X
B
0.3
C A B
0.15 C
C2-2
0.01
C3-1
C3-2
0.01
C4-1
C4-2
0.01
C5-1
C5-2
0.01
C6-1
C6-2
Notes:
0.01
Voltage
Reference
L2OVDD
GND
L2OVDD
GND
VDD
GND
OVDD
GND
OVDD
GND
VDD
GND
1. Dimensioning and tolerancing per ASME Y14.5M, 1994
2. Dimensions in millimeters
3. Top side A1 corner index is a metallized feature with various shapes. Bottom side A1 corner is designated with a ball missing
from the array
39
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
12.3
Substrate Capacitors for the PC7410
Figure 12-8 shows the connectivity of the substrate capacitor pads for the PC7410, 360 HITCE package.
Figure 12-8. Substrate Bypass Capacitors for the PC7410
A1 CORNER
C6-2
C6-1
C5-1
C5-2
Package Caps
C1-1
C1-2
C1-1
C1-2
C2-1
C2-2
C3-1
C4-1
C4-2
C3-2
L2 L1
Value µF Voltage Reference
0.01
0.01
VDD
GND
0.01
OVDD
GND
0.01
OVDD
GND
0.01
VDD
GND
C5-1
C2-2
C2-1
C3-1
C3-2
C5-2
C6-1
C6-2
L2OVDD
GND
0.01
C4-1
C4-2
L2OVDD
GND
40
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 12-9. Mechanical Dimensions and Bottom Surface Nomenclature of the 360-column CI-CGA
Package
2X
0.2
D
PIN A1
INDEX
2X
0.15
B
A
360X
C6
0.15 A
2
1
A3
A4
C5
E2
E4
C1
1
1
2 1
2 1
C4
0.35 A
2
2
E
C2
C3
1
2X
2
0.2
D4
D3
C
D2
E3
TOPVIEW
D1
1 2 3 4 5 6 7 8 9 10 11 1213141516 171819
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
K
A1
A
E1
GND : C1.2 C2.2 C3.2 C4.2 C5.2 C6.2
K
G
A2
C1.1, C2.1 : L2OVDD
360X
B
0.3
T
0.15
T
E
F C3.1, C6.1 : OVDD
C4.1, C5.1 : OVDD
41
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
13. Clock Selection
The PC7410’s PLL is configured by the PLL_CFG[0:3] signals. For a given SYSCLK (bus) frequency,
the PLL configuration signals set the internal CPU and VCO frequency of operation. The PLL configuration for the PC7410 is shown in Table 13-1 for example frequencies. In this example, shaded cells
represent settings that, for a given SYSCLK frequency, result in core and/or VCO frequencies that do not
comply with the minimum and maximum core frequencies listed in Table 9-3 on page 21.
Table 13-1.
PC7410 Microprocessor PLL Configuration(1)(2)(3)(4)(5)
Example Bus-to-Core Frequency in MHz (VCO Frequency in MHz)
PLL_CFG
[0:3]
Bus-toCore
Multiplier
Core-toVCO
Multiplier
0100
2x
2x
0110
2.5x
2x
1000
3x
2x
1110
3.5x
2x
350 (700)
1010
4x
2x
400 (800)
0111
4.5x
2x
1011
5x
2x
1001
5.5x
2x
1101
6x
0101
Bus
33.3 MHz
Bus
50 MHz
Bus
66.6 MHz
Bus
75 MHz
Bus
83.3 MHz
Bus
100 MHz
400 (800)
375 (750)
450 (900)
375 (750)
416 (833)
500 (1000)
366 (733)
412 (825)
458 (916)
2x
400 (800)
450 (900)
500 (1000)
6.5x
2x
433 (866)
488 (967)
0010
7x
2x
350 (700)
466 (933)
0001
7.5x
2x
375 (750)
500
(1000)
1100
8x
2x
400 (800)
0000
9x
2x
450 (900)
0011
PLL off/bypass
PLL off, SYSCLK clocks core circuitry directly, 1x bus-to-core implied
1111
PLL off
PLL off, no core clocking occurs
Notes:
Bus
133 MHz
465 (930)
1. PLL_CFG[0:3] settings not listed are reserved.
2. The sample bus-to-core frequencies shown are for reference only. Some PLL configurations may select bus, core, or VCO
frequencies which are not useful, not supported, or not tested for by the PC7410; see “Clock AC Specifications” on page 20
for valid SYSCLK, core, and VCO frequencies.
3. In PLL-bypass mode, the SYSCLK input signal clocks the internal processor directly, the PLL is disabled, and the bus mode
is set for 1:1 mode operation. This mode is intended for factory use and third- party emulator tool development only.
Note: The AC timing specifications given in this document do not apply in PLL-bypass mode.
4. In PLL-off mode, no clocking occurs inside the PC7410 regardless of the SYSCLK input.
5. PLL-off mode should not be used during chip power-up sequencing.
42
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
The PC7410 generates the clock for the external L2 synchronous data SRAMs by dividing the core clock
frequency of the PC7410. The divided-down clock is then phase-adjusted by an on-chip delay-lock-loop
(DLL) circuit and should be routed from the PC74107410 to the external RAMs. A separate clock output,
L2SYNC_OUT is sent out half the distance to the SRAMs and then returned as an input to the DLL on
pin L2SYNC_IN so that the rising-edge of the clock as seen at the external RAMs can be aligned to the
clocking of the internal latches in the L2 bus interface.
The core-to-L2 frequency divisor for the L2 PLL is selected through the L2CLK bits of the L2CR register.
Generally, the divisor must be chosen according to the frequency supported by the external RAMs, the
frequency of the PC7410 core, and the phase adjustment range that the L2 DLL supports. Table 13-2
shows various example L2 clock frequencies that can be obtained for a given set of core frequencies.
The minimum L2 frequency target is 133 MHz. Sample core-to-L2 frequencies for the PC7410 is shown
in Table 13-2. In this example, shaded cells represent settings that, for a given core frequency, result in
L2 frequencies that do not comply with the minimum and maximum L2 frequencies listed in Table 9-6 on
page 28.
Table 13-2.
Sample Core-to-L2 Frequencies
Core Frequency in MHz
÷1
÷1.5
÷2
÷2.5
÷3
÷3.5
÷4
350
350
233
175
140
–
–
–
366
366
244
183
147
–
–
–
400
400
266
200
160
133
–
–
433
–
288
216
173
144
–
–
450
–
300
225
180
150
–
–
466
–
311
233
186
155
133
–
500
–
333
250
200
166
143
–
Note:
The core and L2 frequencies are for reference only. Some examples may represent core or L2 frequencies
which are not useful, not supported or not tested for by the PC7410; see “L2 Clock AC Specifications” on
page 24 for valid L2CLK frequencies. The L2CR[L2SL] bit should be set for L2CLK frequencies less than
150 MHz.
14. System Design Information
14.1
PLL and DLL Power Supply Filtering
The AVDD and L2AVDD power signals are provided on the PC7410 to supply power to the PLL and DLL,
respectively. Both AVDD and L2AVDD can be supplied power from the VDD power plane. High frequency
noise in the 500 kHz to 10 MHz resonant frequency range of the PLL on the VDD power plane could
affect the stability of the internal clocks.
On systems that use the PC7410 HCTE device, the AVDD and L2AVDD input signals should both implement the circuit shown in Figure 14-1 on page 44.
On systems that use the PC7410 CBGA device, the L2AVDD input should implement the circuit shown in
Figure 14-1.
43
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
When selecting which filter to use on the AVDD input of the PC7410 CBGA device specifically, system
designers should refer to Erratum No. 18 in the PC7410 RISC Microprocessor Chip Errata
(MPC7410CE). The AVDD input of the PC7410 CBGA device is sensitive to system noise on both the
VDD power plane, as described above, and the OVDD power plane as described in the Erratum No. 18.
With these AVDD sensitivities to OVDD and VDD noise, care must be taken when selecting the filter circuit
for the AVDD input of the PC7410 CBGA device. Erratum No. 18 does not apply to the AVDD input of the
MPC7401 HCTE device, nor does it affect the L2AVDD input of either the HCTE or the CBGA device.
As described in Erratum No. 18, when there is a high amount of noise on the OVDD power plane due to
I/O switching rates, it is possible for the OVDD noise to couple into the PLL supply voltage (AVDD) internal
to the PC7410 CBGA package. It is the recommendation of Freescale, that new designs using the
PC7410 CBGA package provide the ability to implement either filter shown in Figure 14-1 and Figure 142 at the AVDD input. Existing designs that implemented Figure 14-1 on AVDD may never experience the
error described in Erratum No. 18. Both new and existing designs should qualify both AVDD filter solutions, and the filter providing the most robust margin should be implemented.
Figure 14-1. PLL Power Supply Filter Circuit No.1
10Ω
AVDD (or L2AVDD)
VDD
2.2 µF
2.2 µF
Low ESL surface mount capacitor
GND
Figure 14-2. PLL Power Supply Filter Circuit No.2
51Ω
AVDD
VDD
Capacitor
Pad Sites
GND
The filter circuit should be placed as close as possible to the AVDD pin to minimize noise coupled from
nearby circuits. A separate circuit should be placed as close as possible to the L2AVDD pin. It is often
possible to route directly from the capacitors to the AVDD pin, which is on the periphery of the 360 CBGA
footprint, without the inductance of vias. The L2AVDD pin may be more difficult to route, but is proportionately less critical.
It is the recommendation of Freescale, that systems that implement the AVDD filter shown in Figure 14-2
design in the pads for the removed capacitors (shown in Figure 14-1), to provide for the possible reintroduction of the filter in Figure 14-1. This would be necessary in case there is a planned transition from the
CBGA package to the HiTCE package of the PC7410.
44
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
14.2
Power Supply Voltage Sequency
The notes in Table 6-1 on page 9 contain cautions about the sequencing of the external bus voltages
and core voltage of the PC7410 (when they are different). These cautions are necessary for the long
term reliability of the part. If they are violated, the electrostatic discharge (ESD) protection diodes will be
forward-biased and excessive current can flow through these diodes. If the system power supply design
does not control the voltage sequencing, one or both of the circuits of Figure 14-3 can be added to meet
these requirements. The MUR420 Schottky diodes of Figure 14-3 control the maximum potential difference between the external bus and core power supplies on power-up and the 1N5820 diodes regulate
the maximum potential difference on power-down.
Figure 14-3. Example Voltage Sequencing Circuits
2.5V
MUR420
MUR420
1.8V
1N5820
1N5820
14.3
Decoupling Recommendations
Due to the PC7410’s dynamic power management feature, large address and data buses and high operating frequencies, the PC7410 can generate transient power surges and high frequency noise in its
power supply, especially while driving large capacitive loads. This noise must be prevented from reaching other components in the PC7410 system and the PC7410 itself requires a clean, tightly regulated
source of power. Therefore, it is recommended that the system designer place at least one decoupling
capacitor at each VDD, OVDD, and L2OVDD pin of the PC7410. It is also recommended that these decoupling capacitors receive their power from separate VDD, (L2)OVDD, and GND power planes in the PCB,
utilizing short traces to minimize inductance.
These capacitors should have a value of 0.01 µF or 0.1 µF. Only ceramic SMT (surface mount technology) capacitors should be used to minimize lead inductance, preferably 0508 or 0603 orientations where
connections are made along the length of the part. Consistent with the recommendations of Dr. Howard
Johnson in High Speed Digital Design: A Handbook of Black Magic (Prentice Hall, 1993) and contrary to
previous recommendations for decoupling PowerPC microprocessors, multiple small capacitors of equal
value are recommended over using multiple values of capacitance.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the VDD, L2OVDD, and OVDD planes to enable quick recharging of the smaller chip capacitors.
These bulk capacitors should have a low ESR (equivalent series resistance) rating to ensure the quick
response time necessary. They should also be connected to the power and ground planes through two
vias to minimize inductance. Suggested bulk capacitors are 100 - 330 µF (AVX TPS tantalum or Sanyo
OSCON).
45
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
14.4
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. Unused active low inputs should be tied to OVDD. Unused active high inputs should be connected
to GND. All NC (no-connect) signals must remain unconnected.
Power and ground connections must be made to all external VDD, OVDD, L2OVDD, and GND pins of the
PC7410.
See “L2 Clock AC Specifications” on page 24 for a discussion of the L2SYNC_OUT and L2SYNC_IN
signals.
14.5
Output Buffer DC Impedance
The PC7410 60x and L2 I/O drivers are characterized over process, voltage and temperature. To measure Z0, an external resistor is connected from the chip pad to OVDD or GND. Then the value of each
resistor is varied until the pad voltage is OVDD/2 (see Figure 14-4).
The output impedance is the average of two components, the resistances of the pull-up and pull-down
devices. When data is held low, SW2 is closed (SW1 is open), and RN is trimmed until the voltage at the
pad equals OVDD/2. RN then becomes the resistance of the pull-down devices. When data is held high,
SW1 is closed (SW2 is open), and RP is trimmed until the voltage at the pad equals OVDD/2. RP then
becomes the resistance of the pull-up devices. RP and RN are designed to be close to each other in
value. Then Z0 = (RP + RN)/2.
Figure 14-4 describes the driver impedance measurement circuit described above.
Figure 14-4. Driver Impedance Measurement Circuit
OVDD
RN
SW2
Pad
Data
SW1
RP
OGND
Alternately, the following is another method to determine the output impedance of the PC7410. A voltage
source, Vforce, is connected to the output of the PC7410, as in Figure 14-4. Data is held low, the voltage
source is set to a value that is equal to (L2)OVDD/2, and the current sourced by Vforce is measured. The
voltage drop across the pull-down device, which is equal to (L2)OVDD/2, is divided by the measured current to determine the output impedance of the pull-down device, RN. Similarly, the impedance of the pullup device is determined by dividing the voltage drop of the pull-up, (L2)OVDD/2, by the current sank by
the pull-up when the data is high and Vforce is equal to (L2)OVDD/2. This method can be employed with
either empirical data from a test setup or with data from simulation models, such as IBIS.
46
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2. Figure 14-5 describes
the alternate driver impedance measurement circuit.
Figure 14-5. Alternate Driver Impedance Measurement Circuit
(L2)OVDD
BGA
Pin
Data
Vforce
OGND
Table 14-1 summarizes the signal impedance results. The driver impedance values were characterized
at 0°, 65°, and 105°C. The impedance increases with junction temperature and is relatively unaffected by
bus voltage.
Table 14-1.
14.6
Impedance Characteristics with VDD = 1.8V, OVDD = 2.5V, TJ = 0° C - 105° C
Impedance
Processor bus
L2 Bus
Symbol
Unit
RN
41.5 – 54.3
42.7 – 54.1
Z0
Ω
RP
37.3 – 55.3
39.3 – 50
Z0
Ω
Pull-up Resistor Requirements
The PC7410 requires pull-up resistors (1 kΩ – 5 kΩ) on several control pins of the bus interface to maintain the control signals in the negated state after they have been actively negated and released by the
PC7410 or other bus masters. These pins are: TS, ARTRY, SHDO, SHD1.
Four test pins also require pull-up resistors (100Ω – 1 kΩ). These pins are CHK, L1_TSTCLK,
L2_TSTCLK, and LSSD_MODE. These signals are for factory use only and must be pulled up to OVDD
for normal machine operation.
If pull-down resistors are used to configure BVSEL or L2VSEL, the resistors should be less than 250Ω.
(see Table 12-1 on page 33). Because PLL_CFG[0:3] must remain stable during normal operation,
strong pull-up and pull-down resistors (1 kΩ or less) are recommended to configure these signals in
order to protect against erroneous switching due to ground bounce, power supply noise or noise
coupling.
In addition, CKSTP_OUT is an open-drain style output that requires a pull-up resistor (1 kΩ–5 kΩ) if it is
used by the system. The CKSTP_IN signal should likewise be pulled up through a pull-up resistor (1 kΩ–
5 kΩ) to prevent erroneous assertions of this signal.
47
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
During inactive periods on the bus, the address and transfer attributes may not be driven by any master
and may, therefore, float in the high-impedance state for relatively long periods of time. Since the
PC7410 must continually monitor these signals for snooping, this float condition may cause excessive
power draw by the input receivers on the PC7410 or by other receivers in the system. These signals can
be pulled up through weak (10 kΩ) pull-up resistors by the system, address bus driven mode can be
enabled (see the PC7410 RISC Microporcessor Family Users’ Manual for more information on this
mode), or these signals may be otherwise driven by the system during inactive periods of the bus to
avoid this additional power draw. The snooped address and transfer attribute inputs are: A[0:31],
AP[0:3], TT[0:4], CI, WT, and GBL.
In systems where GBL is not connected and other devices may be asserting TS for a snoopable transaction while not driving GBL to the processor, we recommend that a strong (1 kΩ) pull-up resistor be used
on GBL. Note that the PC7410 will only snoop transactions when GBL is asserted.
The data bus input receivers are normally turned off when no read operation is in progress and, therefore, do not require pull-up resistors on the bus. Other data bus receivers in the system, however, may
require pull-ups, or that those signals be otherwise driven by the system during inactive periods by the
system. The data bus signals are: DH[0:31], DL[0:31], and DP[0:7].
If address or data parity is not used by the system, and the respective parity checking is disabled through
HID0, the input receivers for those pins are disabled, and those pins do not require pull-up resistors and
should be left unconnected by the system. If parity checking is disabled through HID0, and parity generation is not required by the PC7410 (note that the PC7410 always generates parity), then all parity pins
may be left unconnected by the system. The L2 interface does not normally require pull-up resistors.
14.7
JTAG Configuration Signals
Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the
IEEE 1149.1 specification, but is provided on all processors that implement the PowerPC architecture.
While it is possible to force the TAP controller to the reset state using only the TCK and TMS signals,
more reliable power-on reset performance will be obtained if the TRST signal is asserted during poweron reset.
Because the JTAG interface is also used for accessing the common on-chip processor (COP) function,
simply tying TRST to HRESET is not practical.
The COP function of these processors allows a remote computer system (typically, a PC with dedicated
hardware and debugging software) to access and control the internal operations of the processor. The
COP interface connects primarily through the JTAG port of the processor, with some additional status
monitoring signals. The COP port requires the ability to independently assert HRESET or TRST in order
to fully control the processor. If the target system has independent reset sources, such as voltage monitors, watchdog timers, power supply failures, or push-button switches, then the COP reset signals must
be merged into these signals with logic.
The arrangement shown in Figure 14-6 on page 50 allows the COP port to independently assert
HRESET or TRST, while ensuring that the target can drive HRESET as well. If the JTAG interface and
COP header will not be used, TRST should be tied to HRESET through a 0Ω isolation resistor so that it is
asserted when the system reset signal (HRESET) is asserted ensuring that the JTAG scan chain is initialized during power-on. While Freescale recommends that the COP header be designed into the
system as shown in Figure 14-6, if this is not possible, the isolation resistor will allow future access to
TRST in the case where a JTAG interface may need to be wired onto the system in debug situations.
48
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
The COP header shown in Figure 14-6 on page 50 adds many benefits — breakpoints, watchpoints, register and memory examination/modification, and other standard debugger features are possible through
this interface — and can be as inexpensive as an unpopulated footprint for a header to be added when
needed.
The COP interface has a standard header for connection to the target system, based on the 0.025"
square-post 0.100" centered header assembly (often called a Berg header). The connector typically has
pin 14 removed as a connector key.
There is no standardized way to number the COP header shown in Figure 14-6; consequently, many different pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then
left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter
clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended
in Figure 14-6 is common to all known emulators.
The QACK signal shown in Figure 14-6 is usually connected to the PCI bridge chip in a system and is an
input to the PC7410 informing it that it can go into the quiescent state. Under normal operation this
occurs during a low-power mode selection. In order for COP to work, the PC7410 must see this signal
asserted (pulled down). While shown on the COP header, not all emulator products drive this signal. If
the product does not, a pull-down resistor can be populated to assert this signal. Additionally, some emulator products implement open-drain type outputs and can only drive QACK asserted; for these tools, a
pull-up resistor can be implemented to ensure this signal is deasserted when it is not being driven by the
tool. Note that the pull-up and pull-down resistors on the QACK signal are mutually exclusive and it is
never necessary to populate both in a system. To preserve correct power-down operation, QACK should
be merged via logic so that it also can be driven by the PCI bridge.
49
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Figure 14-6. COP Connector Diagram
SRESET
From Target
Board Sources
(if any)
SRESET
HRESET
HRESET
(6)
QACK
13
11
HRESET
10 kΩ
SRESET
10 kΩ
OVDD
OVDD
10 kΩ
OVDD
10 kΩ
OVDD
0Ω (5)
1
2
3
4
5
6
7
8
9
10
11
12
TRST
6
15
16
COP Connector
Physical Pin Out
OVDD
10 kΩ
2 kΩ
(6)
OVDD
CHKSTP_OUT
CHKSTP_OUT
10 kΩ
Key
14(2)
OVDD
10 kΩ
OVDD
CHKSTP_IN
COP Header
15
VDD_SENSE
5(1)
KEY
13 No pin
TRST
4
CHKSTP_IN
8
TMS
9
1
3
TMS
TDO
TDO
TDI
TDI
TCK
7
2
TCK
QACK
10
NC
12
NC
QACK
2 kΩ(3)
OVDD
10 kΩ(4)
16
Notes:
1. RUN/STOP, normally found on pin 5 of the COP header, is not implemented on the PC7410. Connect
pin 5 of the COP header to OVDD with a 10 kΩ pull-up resistor.
2. Key location; pin 14 is not physically present on the COP header.
3. Component not populated. Populate only if debug tool does not drive QACK.
4. Populate only if debug tool uses an open-drain type output and does not actively deassert QACK.
5. If the JTAG interface is implemented, connect HRESET from the target source to TRST from the COP
header though an AND gate to TRST of the part. If the JTAG interface is not implemented, connect
HRESET from the target source to TRST of the part through a 0Ω isolation resistor.
6. The COP port and target board should be able to independently assert HRESET and TRST to the processor in order to fully control the processor as shown above.
50
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Table 14-2.
COP Pin Definitions
Pins
Signal
Connection
Special Notes
1
TDO
TDO
2
QACK
QACK
3
TDI
TDI
4
TRST
TRST
Add 2K pull-down to ground. Must be merged with on-board TRST if any
See Figure 14-6 on page 50
5
RUN/STOP
No Connect
Used on 604e; leave no-connect for all other processors
6
VDD_SENSE
VDD
Add 2K pull-up to OVDD (for short circuit limiting protection only)
7
TCK
TCK
8
CKSTP_IN
CKSTP_IN
9
TMS
TMS
10
N/A
11
SRESET
12
N/A
13
HRESET
14
N/A
15
CKSTP_OUT
CKSTP_OUT
16
Ground
Digital Ground
Add 2K pull-down to ground. Must be merged with on-board QACK, if any
Optional. Add 10K pull-up to OVDD. Used on several emulator products. Useful for
checkstopping the processor from a logic analyzer of other external trigger
SRESET
Merge with on-board SRESET, if any
HRESET
Merge with on-board HRESET
Key location; pin should be removed
Add 10K pull-up to OVDD
Boundary scan testing is enabled through the JTAG interface signals. (BSDL descriptions of the PC7410
are available on the Internet at www.mot.com/PowerPC/teksupport.) The TRST signal is optional in the
IEEE 1149.1 specification but is provided on all PowerPC implementations. While it is possible to force
the TAP controller to the reset state using only the TCK and TMS signals, more reliable power-on reset
performance will be obtained if the TRST signal is asserted during power-on reset. Since the JTAG interface is also used for accessing the common on-chip processor (COP) function of PowerPC processors,
simply tying TRST to HRESET is not practical.
The common on-chip processor (COP) function of PowerPC processors allows a remote computer system (typically a PC with dedicated hardware and debugging software) to access and control the internal
operations of the processor. The COP interface connects primarily through the JTAG port of the processor with some additional status monitoring signals. The COP port requires the ability to independently
assert HRESET or TRST in order to fully control the processor. If the target system has independent
reset sources, such as voltage monitors, watchdog timers, power supply failures or push-button
switches, then the COP reset signals must be merged into these signals with logic.
The arrangement shown in Figure 14-6 on page 50 allows the COP to independently assert HRESET or
TRST, while ensuring that the target can drive HRESET as well. The pull-down resistor on TRST
ensures that the JTAG scan chain is initialized during power-on if a JTAG interface cable is not attached;
if it is attached, it is responsible for driving TRST when needed.
51
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
The COP header shown in Figure 14-6 on page 50 adds many benefits – breakpoints, watchpoints, register and memory examination/modification and other standard debugger features are possible through
this interface – and can be as inexpensive as an unpopulated footprint for a header to be added when
needed.
The COP interface has a standard header for connection to the target system, based on the 0.025”
square-post 0.100” centered header assembly (often called a “Berg” header). The connector typically
has pin 14 removed as a connector key, as shown in Figure 14-6.
15. Ordering Information
xx
7410
y
xxx
y
nnnn
L
x
Product
(1)
Code
Part
Identifier
Temperature
Range TJ (1)
Package (1)
Screening
Level
Max Internal
(1)
Processor Speed
Application
(1)
Modifier
Revision
(1)
Level
L: 1.8V ± 100 mV
N: 1.5V ± 50 mV
E
PC(X)
Notes:
(2)
7410
V: -40˚C, +110˚C
M: -55˚C, +125˚C
G: CBGA
GS: CI-CBGA
GH: HITCE
U: Upscreening
blank: Std
400 MHz
450 MHz
500 MHz
1. For availability of the different versions, contact your local e2v sales office.
2. The letter X in the part number designates a "Prototype" product that has not been qualified by e2v. Reliability of a PCX partnumber is not guaranteed and such part-number shall not be used in Flight Hardware. Product changes may still occur while
shipping prototypes.
16. Definitions
16.1
Life Support Applications
These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. e2v customers using or
selling these products for use in such applications do so at their own risk and agree to fully indemnify e2v
for any damages resulting from such improper use or sale.
52
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
17. Document Revision History
Table 17-1 provides a revision history for this hardware specification.
Table 17-1.
Document Revision History
Rev. No
Date
Substantive Change(s)
F
01/07
Name change from Atmel to e2v
Table 8-1 on page 18: Changed note 1 to specify that OVDD and L2OVDD power is typically < 5% of VDD power
Figure 12-5 on page 37: revised diagram and dimensions to specify ‘cap regions’ versus individual cap
measurements. Moved individual capacitor placement to separate figure
Figure 12-6 on page 38: Added this figure to show each individual capacitor placement and value
Figure 14-5 on page 47: updated COP Connector Diagram to recommend a weak pull-up resistor on TCK
E
10/2004
Table 9-1 on page 19: Changed measurement test condition IOH from -6mA to -5 mA for VOH and IOL from 6
mA to 5 mA for VOL per product bulletin
“PLL and DLL Power Supply Filtering” on page 43: revised text regarding AVDD filter selection for the CBGA
package
Product specification release subsequent to product qualification
Motorola changed to Freescale
Figure 12-5 on page 37: added package capacitor values
Section "Thermal Management Assistant": deleted
Section “Pull-up Resistor Requirements” on page 47: added recommendation that strong pull-up/down
resistors be used on the PLL_CFG[0:3] signals
Table 9-3 on page 21: removed mode input setup and hold times. These inputs adhere to the general input
setup and hold specifications
D
02/2004
Figure 9-4 on page 24: revised mode input diagram to show sample points around HRESET negation
Figure 14-6 on page 50: added note 6 to emphasize that COP emulator and target board need to be able to
drive HRESET and TRST independently to the CPU
Section “PLL and DLL Power Supply Filtering” on page 43: revised section for HCTE package. Added text and
figure for AVDD filter for the CBGA package
Section “Pull-up Resistor Requirements” on page 47: removed AACK, TEA, and TS from control signals
requiring pull-ups. Removed TBST from snooped transfer attribute list. TBST is an output and is not snooped
53
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
Table of Contents
Features .................................................................................................... 1
Description ............................................................................................... 1
Screening ................................................................................................. 2
1
Block Diagram .......................................................................................... 3
2
General Parameters ................................................................................. 4
3
Overview ................................................................................................... 4
4
Signal Description ................................................................................... 8
5
Detailed Specification ............................................................................. 9
6
Applicable Documents ............................................................................ 9
6.1 Design and Construction ......................................................................................... 9
6.1.1 Terminal Connections ............................................................................. 9
6.2 Absolute Maximum Ratings ..................................................................................... 9
6.3 Recommended Operating Conditions ................................................................... 11
7
Thermal Characteristics ........................................................................ 12
7.1 Package Characteristics ........................................................................................ 12
7.1.1 Package Thermal Characteristics for HiTCE ......................................... 12
7.1.2 Package Thermal Characteristics for CI-CGA ....................................... 13
7.2 Internal Package Conduction Resistance ............................................................. 13
7.3 Thermal Management Information ........................................................................ 13
7.3.1 Adhesives and Thermal Interface Materials .......................................... 14
8
Power Consideration ............................................................................. 17
8.1 Power Management ..............................................................................................17
8.2 Power Dissipation .................................................................................................. 18
9
Electrical Characteristics ...................................................................... 19
9.1 Static Characteristics ............................................................................................. 19
9.2 Dynamic Characteristics ........................................................................................ 20
9.2.1 Clock AC Specifications ........................................................................ 20
9.2.2 Processor Bus AC Specifications .......................................................... 21
9.2.3 L2 Clock AC Specifications ................................................................... 24
9.2.4 L2 Bus AC Specifications ...................................................................... 26
i
0832F–HIREL–02/07
e2v semiconductors SAS 2007
PC7410
9.2.5 IEEE 1149.1 AC Timing Specifications ................................................. 28
10 Preparation for Delivery ........................................................................ 31
10.1 Handling .............................................................................................................. 31
11 Package Mechanical Data ..................................................................... 31
11.1 Parameters .......................................................................................................... 31
12 Pin Assignments .................................................................................... 32
12.1 BGA360 Package ................................................................................................ 32
12.2 Substrate Capacitors for the PC7410 .................................................................. 38
12.3 Substrate Capacitors for the PC7410 .................................................................. 40
13 Clock Selection ...................................................................................... 42
14 System Design Information .................................................................. 43
14.1 PLL and DLL Power Supply Filtering .................................................................. 43
14.2 Power Supply Voltage Sequency ........................................................................ 45
14.3 Decoupling Recommendations ........................................................................... 45
14.4 Connection Recommendations ........................................................................... 46
14.5 Output Buffer DC Impedance .............................................................................. 46
14.6 Pull-up Resistor Requirements ............................................................................ 47
14.7 JTAG Configuration Signals ................................................................................ 48
15 Ordering Information ............................................................................. 52
16 Definitions .............................................................................................. 52
16.1 Life Support Applications ..................................................................................... 52
17 Document Revision History .................................................................. 53
Table of Contents ...................................................................................... i
ii
0832F–HIREL–02/07
e2v semiconductors SAS 2007
How to reach us
Home page: www.e2v.com
Asia Pacifiq
Sales Office:
e2v
United Kingdom
Bank of China Tower
e2v
30th floor office 7
106 Waterhouse Lane
1 Garden Rd Central
Chelmsford
Hong Kong
Essex CM1 2QU
Tel: +852 2251 8227/8/9
Tel: +44 (0)1245 493 493
Fax: +852 2251 8383
Fax: +44 (0)1245 492 492
USA
Product Contact:
e2v
e2v
4 Westchester Plaza
Avenue de Rochepleine
Elmsford
BP 123 - 38521 Saint-Egrève Cedex
NY 10523-1482
France
Tel: +1 914 592 6050
Tel: +33 (0)4 76 58 30 00
Fax: +1 914 592 5148
Hotline:
[email protected]
France
e2v
16 Burospace
F-91 572 Bievres Cedex
Tel: +33 (0) 1 6019 5500
Fax: +33 (0) 1 6019 5529
Whilst e2v has taken care to ensure the accuracy of the information contained herein it accepts no responsibility for the consequences of any
use thereof and also reserves the right to change the specification of goods without notice. e2v accepts no liability beyond that set out in its standard conditions of sale in respect of infringement of third party patents arising from the use of tubes or other devices in accordance with information contained herein.
e2v semiconductors SAS 2007
0832F–HIREL–02/07
PC7410
iv
0832F–HIREL–02/07
e2v semiconductors SAS 2007