AN11748 BGS8L4UK LTE LNA with bypass switch evaluation board Rev. 1 — 17 November 2015 Application note Document information Info Content Keywords BGS8L4UK, LTE, LNA Abstract This document explains the BGS8L4UK LTE LNA evaluation board Ordering info Board-number: OM17018 12NC: 9340 699 48598 Contact information For more information, please visit: http://www.nxp.com AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB Revision history Rev Date Description 1 First publication 20151117 Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 2 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 1. Introduction NXP Semiconductors’ BGS8L4UK LTE LNA Evaluation Board is designed to evaluate the performance of the LTE LNA in its typical application, using: NXP Semiconductors’ BGS8L4UK LTE Low Noise Amplifier A matching inductor A decoupling capacitor NXP Semiconductors’ BGS8L4UK is a low-noise amplifier with bypass switch for LTE receiver applications in an extremely small Wafer-Level Chip-Scale Package (WLCSP), 0.69 mm x 0.44 mm x 0.29 mm; 6 solder bumps (0.25 mm / 0.26 mm bump pitch). The BGS8L4UK features gain of 17.3 dB and a noise figure of 0.8 dB at a current consumption of 4.4 mA. The Bypass switch insertion loss is 1.8 dB. Its superior linearity performance removes interference and noise from co-habitation cellular transmitters, while retaining sensitivity. The LNA components occupy a total area of approximately 1.3 mm2. In this document, the application diagram, board layout, bill of materials, and typical performance are given, as well as some explanations on LTE related RF-parameters like input third-order intercept point IIP3, gain compression and noise. Fig 1. AN11748 Application note BGS8x4UK LTE LNA evaluation board (used for BGS8L4UK, BGS8M4UK) All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 3 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 2. General description of application & product Modern cellular phones have multiple radio systems, so problems like co-habitation are quite common. Since the LTE diversity antenna needs to be placed far from the main antenna to ensure the efficiency of the channel, a low noise amplifier close to the antenna is used to compensate the track-losses (and SAW-filter losses when applicable) on the printed circuit board. A LTE receiver implemented in a mobile phone requires a low current consumption and low Noise Figure. All the different transmit signals that are active in smart phones and tablets can cause problems like inter-modulation and compression. Therefore also a high linearity is required. 2.1 BGS8x4UK: Advantage of integrated By-pass function The major advantage of having a bypass-switch option is the very low current consumption (<1µA) when LTE LNA is not needed in the receive chain (at high RSSI/CQI level, 3~5dB higher than the Sensitivity level). Fig 2 gives a graphical explanation of this advantage. LNA mode setting versus received signal level: LNA Gain Gain mode: Sensitivity enhancement Icc=5-5.5mA LNA Gain By-pass control hysteresis Sensitivity level Received signal strength indicator (RSSI) Higher RSSI Lower RSSI Fig 2. By-pass mode: No gain needed Icc < 1 uA LNA mode setting versus received signal level To avoid frequently switching between Gain- and bypass-mode around chosen Receiver Signal Strength Indicator (RSSI) switching level, one should take a Hysteresis Loop into consideration in the switching logic of the control chip (transceiver or baseband chip), see Fig 2. AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 4 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 3. BGS8L4UK LTE LNA evaluation board The BGS8L4UK LNA evaluation board simplifies the RF evaluation of the BGS8L4UK LTE LNA applied in a LTE front-end, often used in mobile cell phones. The evaluation board enables testing of the device RF performance and requires no additional support circuitry. The board is fully assembled with the BGS8L4UK including the input series inductor and decoupling capacitor. The board is supplied with two SMA connectors for input and output connection to RF test equipment. The BGS8L4UK can operate from a 1.5 V to 3.1 V single supply and consumes typical 4.4 mA. 3.1 Application Circuit The circuit diagram of the evaluation board is shown in Fig 3. With jumper JU1 the control input can be connected either to Vcc (Gain-mode) or GND (Bypass mode). BGS8x4UK LTE LNA EVB BGS8x4UK Fig 3. AN11748 Application note Circuit diagram of the BGS8x4UK LNA evaluation board (used for BGS8L4UK, BGS8M4UK) All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 5 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 3.2 PCB Layout Fig 4. Printed-Circuit Board layout of the BGS8x4UK LNA evaluation board (used for BGS8L4UK, BGS8M4UK) A good PCB layout is an essential part of an RF circuit design. The LNA evaluation board of the BGS8L4UK can serve as a guideline for laying out a board using the BGS8L4UK. Use controlled impedance lines for all high frequency inputs and outputs. Bypass Vcc with decoupling capacitors, preferably located as close as possible to the device. For long bias lines it may be necessary to add decoupling capacitors along the line further away from the device. Proper grounding of the GND pins is also essential for good RF performance. Either connect the GND pins directly to the ground plane or through vias, or do both, which is recommended. The material that has been used for the evaluation board is FR4 using the stack shown in Fig 5. 20um Cu 0.2mm FR4 critical 20um Cu 0.8mm FR4 only for mechanical rigidity of PCB 20um Cu (1) Material supplier is ISOLA DURAVER; εr = 4.6-4.9: T Fig 5. AN11748 Application note Stack of the PCB material All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 6 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 3.3 Bill of materials Table 1. BOM of the BGS8L4UK LTE LNA evaluation board Designator Description Footprint Value Supplier Name/type Comment - WLCSP BGS8L4UK 0.69 mm x 0.44 mm x 0.2 mm, NXP 6 solder bumps (0.252 mm / 0.260 mm bump pitch) PCB 20 x 35mm BGS8L4UK LTE LNA EV Kit C1 Capacitor 0402 1µF Murata GRM1555 Decoupling L1 Inductor 0402 8.2nH Murata LQW15 Input matching X1, X2 SMA RD connector - - Johnson, End launch SMA RF input/ RF output X3 DC header - - Molex, PCB header, Right Angle, 1 Bias connector row, 3 way 90121-0763 X4 JUMPER - - Molex, PCB header, Vertical, 1 row, 3 way 90120-0763 142-0701-841 Stage JU1 Connect Ven to Vcc or separate Ven voltage JUMPER 3.4 BGS8L4UK NXP Semiconductors’ BGS8L4UK LTE low noise amplifier is designed for the LTE low band. The integrated biasing circuit is temperature stabilized, which keeps the current constant over temperature. It also enables the superior linearity performance of the BGS8L4UK. The BGS8L4UK is also equipped with an enable function that allows it to be controlled via a logic signal. In disabled mode it consumes less than1 μA. The output of the BGS8L4UK is internally matched between 728 MHz and 960 MHz, whereas only one series inductor at the input is needed to achieve the best RF performance. The input and output are AC coupled via an integrated capacitor. It requires only two external components to build a LTE LNA having the following advantages: AN11748 Application note Low noise System optimized gain High linearity under jamming 0.69 mm x 0.44 mm x 0.29 mm; 6 solder bumps (0.25 mm / 0.26 mm bump pitch). WLCSP. Low current consumption Short power settling time All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 7 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 3.5 Series inductor The evaluation board is supplied with Murata LQW15 series inductor of 8.2 nH. This is a wire wound type of inductor with high quality factor (Q) and low series resistance (Rs) like the Murata LQW15A series (see Table 2). This type of inductor is recommended in order to achieve the best noise performance. High Q inductors from other suppliers can be used. If it is decided to use other low cost inductors with lower Q and higher Rs the noise performance will degrade. Table 2. Type Series Inductor options Murata Multilayer Size Size Size 0201 0402 0603 LQG Non-Magnetic Core Film Wirewound Non-Magnetic Core AN11748 Application note LQP LQW 15H 18H NF↑↑ NF↑ 03T 15M NF↑↑ NF↑ 15A 18A Default NF↓ All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 Comment Lowest NF © NXP B.V. 2015. All rights reserved. 8 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 4. Typical LNA evaluation board results 4.1 S-Parameters The measured S-Parameters and stability factor K are given in the figures below. For the measurements, a BGS8L4UK-LNA EVB is used ((see Fig 21). Measurements have been carried out using the setup shown in Fig 22. Rollet Stability Factor Small Signal Gain 1000 20 100 0 -10 Gain-mode -20 K-Factor S21 [dB] 10 10 Bypass-mode Gain-mode Bypass-mode 1 -30 0.1 -40 0 2 4 6 Frequency [GHz] 8 0 10 Gain-mode Bypass-mode 0 Fig 6. 2 4 6 Frequency [GHz] 8 10 4 6 8 Frequency [GHz] 10 Output Reflection Coefficient S22 [dB] S11 [dB] Input Reflection Coefficient 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 2 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 Gain-mode Bypass-mode 0 2 4 6 Frequency [GHz] 8 10 BGS8L4UK S-Parameters (typical values). Vcc=2.8V, Pin=-30dBm. Gain mode and Bypass mode AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 9 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB S21 [dB] Small Signal Gain 18 16 14 12 10 8 6 4 2 0 -2 -4 Gain-mode Bypass-mode 0.70 0.75 0.80 0.85 0.90 0.95 1.00 Frequency [GHz] Output Reflection Coefficient Input Reflection Coefficient -4 -6 -12 Gain-mode -14 Bypass-mode -16 -18 0.70 0.75 0.80 0.85 0.90 0.95 1.00 Frequency [GHz] Fig 7. S22 [dB] S11 [dB] -8 -10 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 Gain-mode Bypass-mode 0.70 0.75 0.80 0.85 0.90 0.95 1.00 Frequency [GHz] BGS8L4UK S-Parameters (typical values). Vcc=2.8V, Pin=-30dBm, Gain mode and Bypass mode (Frequency range zoomed in). AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 10 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 4.2 Improving the Gain by optimized matching The design of the BGS8x4UK LTE LNA’s are optimized for best RF-performance using only one input matching coil. In some cases, the Gain can be increased if more in- and output components are used. Fig 8 gives the theoretical maximum gain (Gmax) using (ideal) optimized in- and output matching circuits, and S21 (typical measured performance) of a BGS8L4UK demoboard. BGS8L4UK_110516#1, Vcc=2.8V, Gain Mode 20 Gain [dB] 15 10 Gmax 5 S21 0 -5 0.0E+00 freq [Hz] 740 880 940 Fig 8. AN11748 Application note 5.0E+08 1.0E+09 Gmax(dB) 18.0 17.9 17.8 1.5E+09 Freq [Hz] S21 (dB) 16.6 17.4 17.5 2.0E+09 S11 (dB) -8.0 -11.0 -12.4 2.5E+09 3.0E+09 S22 (dB) -9.1 -20.2 -27.1 S12(dB) -30.5 -29.6 -29.4 S21 and Maximum achievable gain (Gmax) typ. values (Gain mode) All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 11 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB Fig 9 and Fig 10 give an implementation of an improved matching circuit using 3 inductors to increase the Gain. Fig 9. Circuit diagram of the BGS8x4UK LNA evaluation board using 2 input and one output inductor to optimize the Gain. L2 L1 L3 Fig 10. EVB detail of the BGS8x4UK LNA evaluation board using 2 input and one output inductor to optimize the Gain. AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 12 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 4.3 1dB gain compression Strong in-band cell phone TX jammers can cause linearity problems and result in thirdorder intermodulation products in the LTE frequency band. In this chapter the effects of these strong signals is shown. For the measurements, a BGS8L4UK-LNA EVB is used ((see Fig 21). Measurements have been carried out using the setup shown in Fig 22. The gain as function of input power of the DUT was measured between port RFin and RFout of the EVB at the low LTE center frequencies. The figures below show the gain compression curves at LNA-board. Icc vs Input Power, f=740MHz Gain vs Input Power, f=740MHz 25 18 16 14 20 10 15 Vcc=1.5V Vcc=1.8V 10 Vcc=2.8V Gain [dB] Icc [mA] 12 Vcc=3.1V 5 8 Vcc=1.5V 6 Vcc=1.8V 4 Vcc=2.8V 2 Vcc=3.1V 0 -2 0 -4 -30 -25 -20 -15 -10 Pin [dBm] -5 0 5 -30 Fig 11. Icc versus input power , f=740MHz (band 17) -25 -20 -15 -10 Pin [dBm] -5 0 5 Fig 12. Gain versus input power , f=740MHz (band 17) Gain vs Input Power, f=881.5MHz Icc vs Input Power, f=881.5MHz 18 25 16 14 20 Vcc=1.5V Vcc=1.8V 10 Gain [dB] Icc [mA] 12 15 10 Vcc=1.5V 8 Vcc=1.8V Vcc=2.8V 6 Vcc=2.8V Vcc=3.1V 4 Vcc=3.1V 5 2 0 -2 0 -30 -25 -20 -15 -10 Pin [dBm] -5 0 5 Fig 13. Icc versus input power , f=881.5MHz (band 5) AN11748 Application note -30 -25 -20 -15 -10 Pin [dBm] -5 0 5 Fig 14. Gain versus input power , f=881.5MHz (band 5) All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 13 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB Icc vs Input Power, f=942.5MHz Gain vs Input Power, f=942.5MHz 25 18 16 14 20 10 15 Gain [dB] Icc [mA] 12 8 Vcc=1.5V 6 Vcc=1.8V Vcc=2.8V 4 Vcc=2.8V Vcc=3.1V 2 Vcc=3.1V Vcc=1.5V Vcc=1.8V 10 5 0 -2 0 -4 -30 -25 -20 -15 -10 Pin [dBm] -5 0 5 -30 Fig 15. Icc versus input power , f=942.5MHz (band 8) -25 -20 -15 -10 Pin [dBm] -5 0 5 Fig 16. Gain versus input power , f=942.5MHz (band 8) 4.4 IIP3 2-Tone Test The figures below show measured input-IP3-results of the DUT measured with a 2-Tone test at the LTE-bands. For the measurements, a BGS8L4UK-LNA EVB is used (see Fig 21). Measurements have been carried out using the setup shown in Fig 22. Input Power @ Intercept Point of the 3rd Order -1.0 IIP3 [dBm] -1.5 -2.0 f=740MHz (band 17) f=882MHz (band 5) -2.5 f=943MHz (band 8) -3.0 -3.5 1.0 1.5 2.0 2.5 3.0 3.5 Vcc [V] Fig 17. 2-Tone output spectrum, Pin=-30dBm AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 14 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 4.5 Enable Timing Test The following diagram shows the setup to test LNA Turn ON and Turn OFF time. Set the waveform generator to square mode and the output amplitude at 3Vrms with high output impedance. The waveform generator has adequate output current to drive the LNA therefore no extra DC power supply is required which simplifies the test setup. Set the RF signal generator output level to -20dBm at a frequency between 728 MHz and 960 MHz and increase its level until the output DC on the oscilloscope is at 5mV on 1mV/division, the signal generator RF output level is approximately -3dBm. It is very important to keep the cables as short as possible at input and output of the LNA so the propagation delay difference on cables between the two channels is minimized. It is also critical to set the oscilloscope input impedance to 50ohm on channel 2 so the diode detector can discharge quickly to avoid a false result on the Turn OFF time testing. WAVEFORM GENERATOR POWER SUPPLY BGS8x2 LTE LNA EVB X3 GND CTRL OSCILLOSCOPE Vcc X4 ch1: 1M? INPUT Z JU1 C1 6 RF in RF GENERATOR X1 2 L1 5 BGS8x2 Vout RF out 3 4 ch2: 50? INPUT Z X2 1 SCHOTTKY DETECTOR (AGILENT 8473B ) Fig 18. Setup Enable Timing Test Fig 19 and Fig 20 show the measured Ton and T_bypass test. AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 15 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB Fig 19. Results Enable Timing Test. Frq=880MHz, Pin=-20dBm, Vcc=2.8V : Ton~1.2 µs. Fig 20. Results Enable Timing Test. Frq=880MHz, Pin=-20dBm, Vcc=2.8V : T_Bypass~140 ns. AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 16 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 5. Required Measurement Equipment In order to measure the evaluation board the following is necessary: DC Power Supply up to 30 mA at 1.5 V to 3.1 V Two RF signal generators capable of generating RF signals at the LTE operating frequencies between 728 MHz and 960 MHz. An RF spectrum analyzer that covers at least the LTE operating frequencies of 728 MHz to 960 MHz as well as a few of the harmonics. Up to 6 GHz should be sufficient. “Optional” a version with the capability of measuring noise figure is convenient Amp meter to measure the supply current (optional) A network analyzer for measuring gain, return loss and reverse isolation Noise figure analyzer and noise source Directional coupler Proper RF cables 6. Connections and setup The BGS8L4UK LTE LNA evaluation board is fully assembled and tested (see Fig 21). Please follow the steps below for a step-by-step guide to operate the LNA evaluation board and testing the device functions. 1. Connect the DC power supply to the Vcc and GND terminals. Set the power supply to the desired supply voltage, between 1.5 V and 3.1 V, but never exceed 3.1 V as it might damage the BGS8L4UK. 2. Jumper JU1 is connected between the Vcc terminal of the evaluation board and the Ven pin of the BGS8L4UK. 3. Connect the RF signal generator and the spectrum analyzer to the RF input and the RF output of the evaluation board, respectively (Fig 21). Do not turn on the RF output of the signal generator yet, set it to approximately -30 dBm output power at center frequency of the wanted LTE-band and set the spectrum analyzer at the same center frequency and a reference level of 0 dBm. 4. Turn on the DC power supply and it should read approximately 5 mA. 5. Enable the RF output of the generator: The spectrum analyzer displays a tone around –17 dBm. 6. Instead of using a signal generator and spectrum analyzer one can also use a network analyzer in order to measure gain as well as in- and output return loss, P1dB and IP3 (see Fig 22). 7. For noise figure evaluation, either a noise figure analyzer or a spectrum analyzer with noise option can be used. The use of a 5 dB noise source, like the Agilent 364B is recommended. When measuring the noise figure of the evaluation board, any kind of adaptors, cables etc. between the noise source and the evaluation board should be minimized, since this affects the noise figure (see Fig 23). AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 17 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB Fig 21. Evaluation board including its connections Fig 22. 2-Tone Setup for 50Ω LNA board tests (S-Parameters, P1dB and 2-Tone-tests) AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 18 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB Fig 23. Setup diagram for 50Ω LNA-board NF-Measurements. AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 19 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 7. Legal information 7.1 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. 7.2 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. AN11748 Application note Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. Evaluation products — This product is provided on an “as is” and “with all faults” basis for evaluation purposes only. NXP Semiconductors, its affiliates and their suppliers expressly disclaim all warranties, whether express, implied or statutory, including but not limited to the implied warranties of noninfringement, merchantability and fitness for a particular purpose. The entire risk as to the quality, or arising out of the use or performance, of this product remains with customer. In no event shall NXP Semiconductors, its affiliates or their suppliers be liable to customer for any special, indirect, consequential, punitive or incidental damages (including without limitation damages for loss of business, business interruption, loss of use, loss of data or information, and the like) arising out the use of or inability to use the product, whether or not based on tort (including negligence), strict liability, breach of contract, breach of warranty or any other theory, even if advised of the possibility of such damages. Notwithstanding any damages that customer might incur for any reason whatsoever (including without limitation, all damages referenced above and all direct or general damages), the entire liability of NXP Semiconductors, its affiliates and their suppliers and customer’s exclusive remedy for all of the foregoing shall be limited to actual damages incurred by customer based on reasonable reliance up to the greater of the amount actually paid by customer for the product or five dollars (US$5.00). The foregoing limitations, exclusions and disclaimers shall apply to the maximum extent permitted by applicable law, even if any remedy fails of its essential purpose. 7.3 Trademarks Notice: All referenced brands, product names, service names and trademarks are property of their respective owners. All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 20 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 8. List of figures Fig 1. BGS8x4UK LTE LNA evaluation board (used for BGS8L4UK, BGS8M4UK) ................................. 3 Fig 2. LNA mode setting versus received signal level . 4 Fig 3. Circuit diagram of the BGS8x4UK LNA evaluation board (used for BGS8L4UK, BGS8M4UK) ..................................................... 5 Fig 4. Printed-Circuit Board layout of the BGS8x4UK LNA evaluation board (used for BGS8L4UK, BGS8M4UK) ..................................................... 6 Fig 5. Stack of the PCB material ................................. 6 Fig 6. BGS8L4UK S-Parameters (typical values). Vcc=2.8V, Pin=-30dBm. Gain mode and Bypass mode ................................................................. 9 Fig 7. BGS8L4UK S-Parameters (typical values). Vcc=2.8V, Pin=-30dBm, Gain mode and Bypass mode ............................................................... 10 (Frequency range zoomed in). .......................................... 10 Fig 8. S21 and Maximum achievable gain (Gmax) typ. values (Gain mode)......................................... 11 Fig 9. Circuit diagram of the BGS8x4UK LNA evaluation board using 2 input and one output inductor to optimize the Gain. ......................... 12 Fig 10. EVB detail of the BGS8x4UK LNA evaluation board using 2 input and one output inductor to optimize the Gain. ........................................... 12 Fig 11. Icc versus input power , f=740MHz (band 17) . 13 Fig 12. Gain versus input power , f=740MHz (band 17) ........................................................................ 13 Fig 13. Icc versus input power , f=881.5MHz (band 5) 13 Fig 14. Gain versus input power , f=881.5MHz (band 5) ........................................................................ 13 Fig 15. Icc versus input power , f=942.5MHz (band 8) 14 Fig 16. Gain versus input power , f=942.5MHz (band 8) ........................................................................ 14 Fig 17. 2-Tone output spectrum, Pin=-30dBm ............ 14 Fig 18. Setup Enable Timing Test ............................... 15 Fig 19. Results Enable Timing Test. Frq=880MHz, Pin=-20dBm, Vcc=2.8V : Ton~1.2 µs. ............. 16 Fig 20. Results Enable Timing Test. Frq=880MHz, Pin=-20dBm, Vcc=2.8V : T_Bypass~140 ns. .. 16 Fig 21. Evaluation board including its connections ..... 18 Fig 22. 2-Tone Setup for 50Ω LNA board tests (SParameters, P1dB and 2-Tone-tests) ............. 18 Fig 23. Setup diagram for 50Ω LNA-board NFMeasurements. ............................................... 19 AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 21 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 9. List of tables Table 1. Table 2. BOM of the BGS8L4UK LTE LNA evaluation board ................................................................. 7 Series Inductor options ..................................... 8 AN11748 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 17 November 2015 © NXP B.V. 2015. All rights reserved. 22 of 23 AN11748 NXP Semiconductors BGS8L4UK LTE LNA EVB 10. Contents 1. 2. 2.1 3. 3.1 3.2 3.3 3.4 3.5 4. 4.1 4.2 4.3 4.4 4.5 5. 6. 7. 7.1 7.2 7.3 8. 9. 10. Introduction ......................................................... 3 General description of application & product... 4 BGS8x4UK: Advantage of integrated By-pass function .............................................................. 4 BGS8L4UK LTE LNA evaluation board ............. 5 Application Circuit .............................................. 5 PCB Layout ........................................................ 6 Bill of materials ................................................... 7 BGS8L4UK......................................................... 7 Series inductor ................................................... 8 Typical LNA evaluation board results ............... 9 S-Parameters ..................................................... 9 Improving the Gain by optimized matching ...... 11 1dB gain compression ...................................... 13 IIP3 2-Tone Test .............................................. 14 Enable Timing Test .......................................... 15 Required Measurement Equipment ................. 17 Connections and setup ..................................... 17 Legal information .............................................. 20 Definitions ........................................................ 20 Disclaimers....................................................... 20 Trademarks ...................................................... 20 List of figures..................................................... 21 List of tables ...................................................... 22 Contents ............................................................. 23 Please be aware that important notices concerning this document and the product(s) described herein, have been included in the section 'Legal information'. © NXP B.V. 2015. All rights reserved. For more information, visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 17 November 2015 Document identifier: AN11748