ATA6836C - Complete

ATA6836C
Hex Half-bridge Driver with Serial Input Control
DATASHEET
Features
● Six half-bridge outputs formed by six high-side and six low-side drivers
● Capable of switching all kinds of loads (such as DC motors, bulbs, resistors,
capacitors and inductors)
● RDSon typically 1.0 at 25°C, maximum 1.8 at 150°C
● Up to 650-mA output current
● Very low quiescent current IVS < 2µA in standby mode
● Outputs short-circuit protected
● Overtemperature prewarning and protection
● Undervoltage protection
● Various diagnosis functions such as shorted output, open load, overtemperature
and power supply fail
● Serial data interface
● Operation voltage up to 40V
● Daisy chaining possible
● Serial interface 5V compatible, up to 2MHz clock frequency
● SO28 or QFN24 power package
4952O-AUTO-02/15
1.
Description
The Atmel® ATA6836C is a fully protected hex half-bridge driver designed in Smart Power SOI technology, used to control
up to six different loads by a microcontroller in automotive and industrial applications.
Each of the six high-side and six low-side drivers is capable of driving currents up to 650mA. The drivers are internally
connected to form six half-bridges and can be controlled separately from a standard serial data interface. Therefore, all kinds
of loads, such as bulbs, resistors, capacitors and inductors, can be combined. The IC especially supports the application of
H-bridges to drive DC motors.
Protection is guaranteed in terms of short-circuit conditions, overtemperature and undervoltage. Various diagnosis functions
and a very low quiescent current in standby mode make a wide range of applications possible.
Automotive qualification referring to conducted interferences, EMC protection and ESD protection gives added value and
enhanced quality for the exacting requirements of automotive applications.
Figure 1-1. Block Diagram SO28
S
I
S
C
T
O
L
D
H
S
6
L
S
6
H
S
5
H
S
4
L
S
5
L
S
4
H
S
3
L
S
3
H
S
2
L
S
2
H
S
1
L
S
1
S
R
R
5, 10
VS
Input register
Ouput register
DI
26
P
S
F
I
N
H
S
C
D
H
S
6
Serial interface
L
S
6
H
S
5
L
S
5
H
S
4
L
S
4
H
S
3
L
S
3
H
S
2
L
S
2
H
S
1
Charge
pump
L
S
1
T
P
20
GND
21
GND
22
GND
CLK
23
25
GND
CS
24
INH
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
UV
protection
Fault
Detect
19
17
Control
logic
DO
18
VCC
Power on
reset
6
GND
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
7
Fault
Detect
GND
Thermal
protection
8
GND
9
15, 16
OUT1
2
ATA6836C [DATASHEET]
4952O–AUTO–02/15
13, 14
OUT2
11, 12
OUT3
3, 4
OUT4
1, 2
OUT5
27, 28
OUT6
GND
Figure 1-2. Block Diagram QFN24
S
I
S
C
T
O
L
D
H
S
6
L
S
6
H
S
5
L
S
5
H
S
4
L
S
4
H
S
3
L
S
3
H
S
2
L
S
2
H
S
1
L
S
1
S
R
R
3, 4
VS
Input register
Ouput register
DI
19
P
S
F
I
N
H
S
C
D
H
S
6
Serial interface
L
S
6
H
S
5
L
S
5
H
S
4
L
S
4
H
S
3
L
S
3
H
S
2
L
S
2
H
S
1
Charge
pump
L
S
1
T
P
CLK
18
CS
17
INH
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
UV
protection
Fault
Detect
14
12
Control
logic
DO
13
VCC
Power on
reset
24
GND
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
16
Fault
Detect
GND
Thermal
protection
15
GND
7
11
OUT1
8
5
2
OUT2
OUT3
OUT4
23
OUT5
GND
20
OUT6
ATA6836C [DATASHEET]
4952O–AUTO–02/15
3
2.
Pin Configuration
2.1
SO28
Figure 2-1. Pinning SO28
OUT5
OUT5
OUT4
OUT4
VS
GND
GND
GND
GND
VS
OUT3
OUT3
OUT2
OUT2
Table 2-1.
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
OUT6
OUT6
DI
CLK
CS
GND
GND
GND
GND
VCC
DO
INH
OUT1
OUT1
Pin Description SO28
Pin
Symbol
Function
1, 2
OUT5
Half-bridge output 5; formed by internally connected power MOS high-side switch 5 and lowside switch 5 with internal reverse diodes; short circuit protection; overtemperature protection;
diagnosis for short and open load
3, 4
OUT4
Output 4; see pin 1
5
VS
6, 7, 8, 9
GND
10
VS
11, 12
OUT3
Output 3; see pin 1
13, 14
OUT2
Output 2; see pin 1
15, 16
OUT1
Output 1; see pin 1
17
INH
Inhibit input, 5V logic input with internal pull down, low = standby, high = normal operation
18
DO
Serial data output, 5V CMOS logic level tri-state output for output (status) register data, sends
16-bit status information to the microcontroller (LSB is transferred first). Output will remain tristated unless device is selected by CS = low; therefore, several ICs can operate on one data
output line only
19
VCC
Logic supply voltage (5V)
20, 21,
22, 23
GND
Ground, see pins 6 to 9
24
CS
Chip select input, 5V CMOS logic level input with internal pull up;
low = serial communication is enabled, high = disabled
25
CLK
Serial clock input, 5V CMOS logic level input with internal pull down,
controls serial data input interface and internal shift register (fmax = 2MHz)
26
DI
27, 28
OUT6
Power supply output stages HS4, HS5, HS6, internal supply; external connection to pin 10
necessary
Ground; reference potential; internal connection to pins 20 to 23; cooling tab
Power supply output stages HS1, HS2 and HS3
Serial data input; 5V CMOS logic level input with internal pull down; receives serial data from
the control device; DI expects a 16-bit control word with LSB being transferred first
Output 6; see pin 1
ATA6836C [DATASHEET]
4952O–AUTO–02/15
QFN24
NC
OUT5
OUT5 SENSE
OUT6 SENSE
OUT6
DI
Figure 2-2. Pinning QFN24, 5  5, 0.65mm pitch
OUT4 SENSE
OUT4
VS
VS
OUT3
OUT3 SENSE
1
2
3
4
5
6
24 23 22 21 20 19
18
17
16
15
14
13
7 8 9 10 11 12
CLK
CS
GND SENSE
NC
VCC
DO
NC
OUT2
OUT2 SENSE
OUT1 SENSE
OUT1
INH
2.2
Note:
YWW
ATAxyz
ZZZZZ
AL
Table 2-2.
Pin Description QFN24
Pin
1
Symbol
Date code (Y = Year above 2000, WW = week number)
Product name
Wafer lot number
Assembly sub-lot number
Function
OUT4 SENSE Only for testability in final test
Half-bridge output 4; formed by internally connected power MOS high-side switch 4 and lowside switch 4 with internal reverse diodes; short circuit protection; overtemperature protection;
diagnosis for short and open load
2
OUT4
3
VS
Power supply output stages HS4, HS5 and HS6
4
VS
Power supply output stages HS1, HS2 and HS3
5
OUT3
6
7
8
Output 3; see pin 1
OUT3 SENSE Only for testability in final test
NC
OUT2
Internal bond to GND
Output 2; see pin 1
9
OUT2 SENSE Only for testability in final test
10
OUT1 SENSE Only for testability in final test
11
OUT1
12
INH
Inhibit input; 5V logic input with internal pull down; low = standby, high = normal operation
13
DO
Serial data output; 5V CMOS logic level tri-state output for output (status) register data; sends
16-bit status information to the microcontroller (LSB is transferred first). Output will remain tristated unless device is selected by CS = low, therefore, several ICs can operate on one data
output line only
14
VCC
Logic supply voltage (5V)
15
NC
16
Output 1; see pin 1
Internal bond to GND
GND SENSE Ground; reference potential; internal connection to the lead frame; cooling tab
ATA6836C [DATASHEET]
4952O–AUTO–02/15
5
Table 2-2.
6
Pin Description QFN24 (Continued)
Pin
Symbol
Function
17
CS
Chip select input; 5V CMOS logic level input with internal pull up;
low = serial communication is enabled, high = disabled
18
CLK
Serial clock input; 5V CMOS logic level input with internal pull down;
controls serial data input interface and internal shift register (fmax = 2MHz)
19
DI
20
OUT6
Serial data input; 5V CMOS logic level input with internal pull down; receives serial data from
the control device; DI expects a 16-bit control word with LSB being transferred first
Output 6; see pin 1
21
OUT6 SENSE Only for testability in final test
22
OUT5 SENSE Only for testability in final test
23
OUT5
24
NC
ATA6836C [DATASHEET]
4952O–AUTO–02/15
Output 5; see pin 1
Internal bond to GND
3.
Functional Description
3.1
Serial Interface
Data transfer starts with the falling edge of the CS signal. Data must appear at DI synchronized to CLK and is accepted on
the falling edge of the CLK signal. LSB (bit 0, SRR) has to be transferred first. Execution of new input data is enabled on the
rising edge of the CS signal. When CS is high, pin DO is in a tri-state condition. This output is enabled on the falling edge of
CS. Output data will change their state with the rising edge of CLK and stay stable until the next rising edge of CLK appears.
LSB (bit 0, TP) is transferred first.
Figure 3-1. Data Transfer Input Data Protocol
CS
DI
SRR
0
LS1
HS1
LS2
1
2
3
SLS1
SHS1
SLS2
HS2
LS3
HS3
LS4
4
5
6
7
8
9
10
SHS2
SLS3
SHS3
SLS4
SHS4
SLS5
SHS5
HS4
LS5
HS5
LS6
11
HS6
12
OLD
13
SCT
14
SI
15
CLK
DO
TP
Table 3-1.
SLS6
SHS6
SCD
INH
PSF
Input Data Protocol
Bit
Input Register
Function
0
SRR
Status register reset (high = reset; the bits PSF, SCD and overtemperature shutdown
in the output data register are set to low)
1
LS1
Controls output LS1 (high = switch output LS1 on)
2
HS1
Controls output HS1 (high = switch output HS1 on)
3
LS2
See LS1
4
HS2
See HS1
5
LS3
See LS1
6
HS3
See HS1
7
LS4
See LS1
8
HS4
See HS1
9
LS5
See LS1
10
HS5
See HS1
11
LS6
See LS1
12
HS6
See HS1
13
OLD
Open load detection (low = on)
14
SCT
Programmable time delay for short circuit
(shutdown delay high/low = 12ms/1.5ms)
15
SI
Software inhibit; low = standby, high = normal operation
(data transfer is not affected by standby function because the digital part is still
powered)
ATA6836C [DATASHEET]
4952O–AUTO–02/15
7
Table 3-2.
Output Data Protocol
Bit
Output (Status)
Register
0
TP
1
Status LS1
Normal operation: high = output is on, low = output is off
Open-load detection: high = open load, low = no open load
(correct load condition is detected if the corresponding output is switched off)
2
Status HS1
Normal operation: high = output is on, low = output is off
Open-load detection: high = open load, low = no open load
(correct load condition is detected if the corresponding output is switched off)
3
Status LS2
Description see LS1
4
Status HS2
Description see HS1
5
Status LS3
Description see LS1
6
Status HS3
Description see HS1
7
Status LS4
Description see LS1
8
Status HS4
Description see HS1
9
Status LS5
Description see LS1
10
Status HS5
Description see HS1
11
Status LS6
Description see LS1
12
Status HS6
Description see HS1
13
SCD
Short circuit detected: set high, when at least one output is switched off by a short
circuit condition
14
INH
Inhibit: this bit is controlled by software (bit SI in input register) and hardware inhibit
(pin INH). High = standby, low = normal operation
15
Status of the Input Register After Power on Reset
Bit 15 Bit 14
(SI)
(SCT)
H
8
Temperature prewarning: high = warning
(overtemperature shutdown see remark below)
PSF
Power supply fail: undervoltage at pin VS detected
Bit 0 to 15 = high: overtemperature shutdown
Note:
Table 3-3.
Function
H
Bit 13
(OLD)
Bit 12
(HS6)
Bit 11
(LS6)
Bit 10
(HS5)
Bit 9
(LS5)
Bit 8
(HS4)
Bit 7
(LS4)
Bit 6
(HS3)
Bit 5
(LS3)
Bit 4
(HS2)
Bit 3
(LS2)
H
L
L
L
L
L
L
L
L
L
L
ATA6836C [DATASHEET]
4952O–AUTO–02/15
Bit 2 Bit 1 Bit 0
(HS1) (LS1) (SRR)
L
L
L
3.2
Power-supply Fail
In case of undervoltage at pin VS, an internal timer is started. When during a permanent undervoltage the delay time (tdUV) is
reached, the power supply fail bit (PSF) in the output register is set and all outputs are disabled. When normal voltage is
present again, the outputs are enabled immediately. The PSF bit remains high until it is reset by the SRR bit in the input
register.
3.3
Open-load Detection
If the open-load detection bit (OLD) is set to low, a pull-up current for each high-side switch and a pull-down current for each
low-side switch is turned on (open-load detection current IHS1-6, ILS1-6). If VVS – VHS1-6 or VLS1-6 is lower than the open-load
detection threshold (open-load condition), the corresponding bit of the output in the output register is set to high. Switching
on an output stage with OLD bit set to low disables the open load function for this output.
3.4
Overtemperature Protection
If the junction temperature exceeds the thermal prewarning threshold, TjPW set, the temperature prewarning bit (TP) in the
output register is set. When the temperature falls below the thermal prewarning threshold, TjPW reset, the bit TP is reset. The
TP bit can be read without transferring a complete 16-bit data word: with CS = high to low, the state of TP appears at pin DO.
After the microcontroller has read this information, CS is set high and the data transfer is interrupted without affecting the
state of the input and output registers.
If the junction temperature exceeds the thermal shutdown threshold, Tj switch off, the outputs are disabled and all bits in the
output register are set high. The outputs can be enabled again when the temperature falls below the thermal shutdown
threshold, Tj switch on, and when a high has been written to the SRR bit in the input register. Thermal prewarning and
shutdown threshold have hysteresis.
3.5
Short-circuit Protection
The output currents are limited by a current regulator. Current limitation takes place when the overcurrent limitation and
shutdown threshold (IHS1-6, ILS1-6) are reached. Simultaneously, an internal timer is started. The shorted output is disabled
when during a permanent short the delay time (tdSd) programmed by the short-circuit timer bit (SCT) is reached. Additionally,
the short-circuit detection bit (SCD) is set. If the temperature prewarning bit TP in the output register is set during a short, the
shorted output is disabled after tdSd and SCD bit is set. By writing a high to the SRR bit in the input register, the SCD bit is
reset and the disabled outputs are enabled.
3.6
Inhibit
There are two ways to inhibit the Atmel® ATA6836C:
● Set bit SI in the input register to 0
●
Switch pin INH to 0V
In both cases, all output stages are turned off but the serial interface stays active. The output stages can be activated again
by bit SI = 1 (when INH = VCC) or by pin INH switched back to VCC (when SI = 1).
ATA6836C [DATASHEET]
4952O–AUTO–02/15
9
4.
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
All values refer to GND pins.
Pin SO28
Pin
QFN24
Symbol
Value
Unit
Supply voltage
5, 10
3, 4
VVS
–0.3 to +40
V
Supply voltage t < 0.5s; IS > –2A
5, 10
3, 4
VVS
–1
V
Supply voltage difference
VS_pin5(3) – VS_pin10(4)
5, 10
3, 4
VVS
150
mV
19
14
VVCC
–0.3 to +7
V
24-26
17-19
VDI, VCLK, VCS
–0.3 to VVCC +0.3
V
18
13
VDO
–0.3 to VVCC +0.3
V
IINH, IDI, ICLK, ICS
–10 to +10
mA
IDO
–10 to +10
mA
1-4, 11- 2, 5, 8, 11,
16, 27, 28
20, 23
IOUT1 to IOUT6
Internally limited, see
“Output Specification” in
Section 7. on page 11
2, 3, 12, 2, 5, 8, 11,
13, 15, 28
20, 23
OUT1 to OUT6
Parameters
Logic supply voltage
Logic input voltage
Logic output voltage
Input current
17, 24-26 12, 17-19
Output current
18
Output current
Output voltage
13
1, 4, 11,
14, 16, 27
–0.3 to +40
V
Junction temperature range
Tj
–40 to +150
°C
Storage temperature range
TSTG
–55 to +150
°C
5.
Thermal Resistance
Table 5-1.
SO28
Parameter
Test Conditions
Pin
Symbol
Max.
Unit
Junction pin
Measured to GND
6 to 9, 20 to 23
RthJP
25
K/W
RthJA
65
K/W
Max.
Unit
Junction ambient
Table 5-2.
Typ.
QFN24: Depends on the PCB-board
Parameter
Test Conditions
Junction pin
Junction ambient
10
Min.
ATA6836C [DATASHEET]
4952O–AUTO–02/15
Pin
Symbol
Min.
Typ.
16
RthJP
<5
K/W
RthJA
35
K/W
6.
Operating Range
Parameter
Test Conditions
Pin SO28 Pin QFN24
Min.
Max.
Unit
40
V
5, 10
3, 4
VVS
19
14
VVCC
4.75
5.25
V
17, 24-26
12, 17-19
VINH, VDI, VCLK,
VCS
–0.3
VVCC
V
2
MHz
+150
°C
Logic supply voltage
Serial interface clock
frequency
fCLK
Junction temperature
range
Tj
7.
Typ.
VUV(1)
Supply voltage
Logic input voltage
Symbol
–40
Electrical Characteristics
7.5V < VS < 40V; 4.75 < VCC < 5.25V; INH = High; –40°C < Tj < 150°C; unless otherwise specified, all values refer to GND pins.
No. Parameters
1
Test Conditions
Pin SO28 Pin QFN24
Symbol
Min.
Typ.
Max.
Unit Type*
Current Consumption
VS = 33V
VCC = 0V or
Total quiescent current
VCC = 5V, bit SI = low or
1.1 (VS and all outputs to
VCC = 5V, pin INH = low
VS)
Output pins to VS and
GND
Quiescent current
1.2
(VCC)
5, 10
3, 4
IVS
2
µA
A
4.75V < VVCC < 5.25V,
INH or bit SI = low
19
14
IVCC
20
µA
A
4.75V < VVCC < 5.25V,
INH or bit SI = low,
TJ = –40°C
19
14
IVCC
30
µA
A
1.2
mA
A
1.3 Supply current (VS)
VVS < 28V normal
operation, all output
stages off
5, 10
3, 4
IVS
1.4 Supply current (VS)
VVS < 28V normal
operation, all output low
stages on, no load
5, 10
3, 4
IVS
10
mA
A
1.5 Supply current (VS)
VVS < 28V normal
operation, all output high
stages on, no load
5, 10
3, 4
IVS
16
mA
A
1.6 Supply current (VCC)
4.75V < VVCC < 5.25V,
normal operation
19
14
IVCC
150
µA
A
Discharge current
(VS)
VVS = 40V, INH = low
5, 10
3, 4
IVS
5
mA
A
45
kHz
A
3.0
V
A
1.7
2
2.1
3
3.1
0.8
Internal Oscillator Frequency
Frequency (time base
for delay timers)
fOSC
19
VVCC
2.3
Undervoltage Detection, Power-on Reset
Power-on reset
threshold
19
14
2.7
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
1.
Delay time between rising edge of input signal at pin CS after data transmission and switch on/off output stages to 90%
of final level. Device not in standby for t > 1ms.
ATA6836C [DATASHEET]
4952O–AUTO–02/15
11
7.
Electrical Characteristics (Continued)
7.5V < VS < 40V; 4.75 < VCC < 5.25V; INH = High; –40°C < Tj < 150°C; unless otherwise specified, all values refer to GND pins.
No. Parameters
Test Conditions
Pin SO28 Pin QFN24
Symbol
Min.
Typ.
Max.
tdPor
30
95
160
µs
A
5.5
7.0
V
A
V
A
21
ms
A
3.2
Power-on reset delay
After switching on VVCC
time
3.3
Undervoltage
detection threshold
19
14
VUV
3.4
Undervoltage
detection hysteresis
19
14
VUV
3.5
Undervoltage
detection delay
0.4
Unit Type*
tdUV
7
4.1 Thermal prewarning
TjPWset
120
145
170
°C
B
4.2 Thermal prewarning
TjPWreset
105
130
155
°C
B
K
C
4
4.3
Thermal Prewarning and Shutdown
Thermal prewarning
hysteresis
TjPW
15
4.4 Thermal shutdown
Tj switch off
150
175
200
°C
B
4.5 Thermal shutdown
Tj switch on
135
160
185
°C
B
Thermal shutdown
hysteresis
Tj switch off
K
C
4.6
Ratio thermal
4.7 shutdown/thermal
prewarning
Tj switch off/
1.05
1.2
C
1.05
1.2
C
TjPW set
Ratio thermal
4.8 shutdown/thermal
prewarning
5
15
Tj switch on/
TjPW reset
Output Specification (LS1-LS6, HS1-HS6) 7.5V < VVS < 40V
5.1 On resistance
IOut = 600mA
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
RDS OnL
1.8

A
5.2 On resistance
IOut = –600mA
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
RDS OnH
1.8

A
High-side output
leakage current
5.3
(total quiescent
current see 1.1)
VOut1-6 = 0V
all output stages off
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
IOut1-6
µA
A
Low-side output
leakage current
5.4
(total quiescent
current see 1.1)
VOut1-6 = VS
all output stages off
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
IOut1-6
120
µA
A
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
Woutx
15
mJ
D
Overcurrent limitation
5.6 and shutdown
VVS = 13V
threshold
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
ILS1-6
650
950
1400
mA
A
Overcurrent limitation
5.7 and shutdown
VVS = 13V
threshold
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
IHS1-6
–1400
–950
–650
mA
A
5.5
Inductive shutdown
energy
–15
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
1.
Delay time between rising edge of input signal at pin CS after data transmission and switch on/off output stages to 90%
of final level. Device not in standby for t > 1ms.
12
ATA6836C [DATASHEET]
4952O–AUTO–02/15
7.
Electrical Characteristics (Continued)
7.5V < VS < 40V; 4.75 < VCC < 5.25V; INH = High; –40°C < Tj < 150°C; unless otherwise specified, all values refer to GND pins.
No. Parameters
Test Conditions
Pin SO28 Pin QFN24
Symbol
Min.
Typ.
Max.
Unit Type*
Overcurrent limitation
5.8 and shutdown
20V < VVS < 40V
threshold
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
ILS1-6
650
950
1600
mA
C
Overcurrent limitation
5.9 and shutdown
20V < VVS < 40V
threshold
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
IHS1-6
–1600
–950
–650
mA
C
5.10
Input register
Overcurrent shutdown
bit 14 (SCT) = low
delay time
VVS = 13V
tdSd
0.9
1.5
2.1
ms
A
5.11
Input register
Overcurrent shutdown
bit 14 (SCT) = High
delay time
VVS = 13V
tdSd
7
12
17
ms
A
5.12
High-side open load
detection current
Input register bit 13
(OLD) = low, output off
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
IOut1-6H
–1.5
–0.4
mA
A
5.13
Low-side open load
detection current
Input register bit 13
(OLD) = low, output off
1-4, 11- 2, 5, 8, 11,
16, 27, 28 20, 23
IOut1-6L
0.4
1.5
mA
A
5.14
Open load detection
current ratio
2, 5, 8, 11,
20, 23
IOLoutLX/
IOLoutHX
1.05
5.15
High-side open load
detection voltage
Input register bit 13
2, 5, 8, 11,
(OLD) = low, output off, 1-4, 11-16
20, 23
reference: VS
VOut1-6H
–2.5
–0.6
V
A
5.16
Low-side open load
detection voltage
Input register bit 13
(OLD) = low, output off
VOut1-6L
0.6
2
V
A
5.17
High-side output
switch on delay(1)
VVS = 13V
RLoad = 30
tdon
20
µs
A
5.18
Low-side output switch VVS = 13V
on delay(1)
RLoad = 30
tdon
20
µs
A
5.19
High-side output
switch off delay(1)
VVS =13V
RLoad = 30
tdoff
20
µs
A
5.20
Low-side output switch VVS =13V
off delay(1)
RLoad = 30
tdoff
3
µs
A
1-4, 11-16
1-4, 11-16
2, 5, 8, 11,
20, 23
Dead time between
VVS =13V
5.21 corresponding highRLoad = 30
and low-side switches
6
1.2
2
tdon – tdoff
1
µs
A
0.3 
VVCC
V
A
0.7 
VVCC
V
A
Inhibit Input
6.1
Input voltage low-level
threshold
17
12
VIL
6.2
Input voltage highlevel threshold
17
12
VIH
6.3
Hysteresis of input
voltage
17
12
VI
100
700
mV
A
IPD
10
80
µA
A
6.4 Pull-down current
VINH = VVCC
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
1.
Delay time between rising edge of input signal at pin CS after data transmission and switch on/off output stages to 90%
of final level. Device not in standby for t > 1ms.
ATA6836C [DATASHEET]
4952O–AUTO–02/15
13
7.
Electrical Characteristics (Continued)
7.5V < VS < 40V; 4.75 < VCC < 5.25V; INH = High; –40°C < Tj < 150°C; unless otherwise specified, all values refer to GND pins.
No. Parameters
7
Test Conditions
Pin SO28 Pin QFN24
Symbol
Min.
0.3 
VVCC
Max.
Unit Type*
Serial Interface: Logic Inputs DI, CLK, CS
7.1
Input voltage low-level
threshold
24-26
17-19
VIL
7.2
Input voltage highlevel threshold
24-26
17-19
VIH
7.3
Hysteresis of input
voltage
24-26
17-19
VI
7.4
Pull-down current pin
VDI, VCLK = VVCC
DI, CLK
25, 26
18, 19
24
7.5 Pull-up current pin CS VCS= 0V
8
Typ.
V
A
0.7 
VVCC
V
A
50
500
mV
A
IPDSI
2
50
µA
A
17
IPUSI
–50
–2
µA
A
0.5
V
A
V
A
µA
A
Serial Interface: Logic Output DO
8.1
Output voltage low
level
IOL = 3mA
18
13
VDOL
8.2
Output voltage high
level
IOL = –1mA
18
13
VDOH
VVCC –
0.7V
8.3
Leakage current
(tri-state)
VCS = VVCC,
0V < VDO < VVCC
18
13
IDO
–10
10
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
1.
Delay time between rising edge of input signal at pin CS after data transmission and switch on/off output stages to 90%
of final level. Device not in standby for t > 1ms.
8.
Serial Interface: Timing
Pin SO28
QFN24
Number in
Timing
Diagram
(Figure 8-1
on page 15)
CDO = 100pF
18
13
1
tENDO
200
ns
DO disable after CS
rising edge
CDO = 100pF
18
13
2
tDISDO
200
ns
DO fall time
CDO = 100pF
18
13
-
tDOf
100
ns
DO rise time
CDO = 100pF
18
13
-
tDOr
100
ns
DO valid time
CDO = 100pF
18
13
10
tDOVal
200
ns
CS setup time
24
17
4
tCSSethl
225
ns
CS setup time
24
17
8
tCSSetlh
225
ns
Parameters
Test Conditions
DO enable after CS
falling edge
Symbol Min. Typ. Max. Unit
CS high time
Input register bit 14 (SCT) = high
24
17
9
tCSh
17
ms
CS high time
Input register bit 14 (SCT) = low
24
17
9
tCSh
2.1
ms
CLK high time
25
18
5
tCLKh
225
ns
CLK low time
25
18
6
tCLKl
225
ns
CLK period time
25
18
-
tCLKp
500
ns
CLK setup time
25
18
7
tCLKSethl
225
ns
CLK setup time
25
18
3
tCLKSetlh
225
ns
DI setup time
26
19
11
tDIset
40
ns
DI hold time
26
19
12
tDIHold
40
ns
14
ATA6836C [DATASHEET]
4952O–AUTO–02/15
Figure 8-1. Serial Interface Timing Diagram with Item Numbers
1
2
CS
DO
9
CS
4
7
CLK
5
3
6
8
DI
11
CLK
10
12
DO
Inputs DI, CLK, CS: High level = 0.7 x VCC, low level = 0.2 x VCC
Output DO: High level = 0.8 x VCC, low level = 0.2 x VCC
ATA6836C [DATASHEET]
4952O–AUTO–02/15
15
9.
Noise and Surge Immunity
Parameters
Test Conditions
Value
Conducted interferences
ISO 7637-1
Level 4(1)
Interference suppression
VDE 0879 Part 2
Level 5
ESD (Human Body Model)
ESD S 5.1
4kV
CDM (Charge Device Model)
ESD STM5.3
750V for corner pins
(SO package only)
500V all other pins
MM (Machine Model)
Note:
1. Test pulse 5: Vvbmax = 40V
ESD STM5.2
200V
16
ATA6836C [DATASHEET]
4952O–AUTO–02/15
10.
Application Circuit
Figure 10-1. Application Circuit
S
I
VCC
O
L
D
H
S
6
L
S
6
H
S
5
L
S
5
H
S
4
L
S
4
H
S
3
L
S
3
H
S
2
L
S
2
H
S
1
L
S
1
VS
S
R
R
BYT41D
VS
Input register
Ouput register
Trigger
Reset
U5021M Enable
Watchdog
S
C
T
DI
P
S
F
I
N
H
S
C
D
H
S
6
+
Serial interface
L
S
6
H
S
5
L
S
5
H
S
4
L
S
4
H
S
3
L
S
3
H
S
2
L
S
2
H
S
1
Charge
pump
L
S
1
Vbatt
24V
GND
T
P
GND
GND
CLK
Microcontroller
GND
CS
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
VCC
UV
protection
Fault
Detect
INH
Control
logic
DO
VCC
Power on
reset
+
VCC
5V
GND
Fault
Detect
VCC
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
Fault
Detect
GND
Thermal
protection
GND
GND
OUT1
M
10.1
OUT2
M
OUT3
M
OUT4
M
OUT5
OUT6
M
Application Notes
●
●
Connect the blocking capacitors at VCC and VS as close as possible to the power supply and GND pins.
●
Recommended value for capacitors at VCC:
Electrolytic capacitor C > 10µF in parallel with a ceramic capacitor C = 100nF.
●
To reduce thermal resistance, place cooling areas on the PCB as close as possible to GND pins and to the die paddle
in QFN24.
●
Only for the QFN24 versions: The sense pins OUTx SENSE can either be left open or can be connected to the
adjacent OUTx pin. Never use the sense pins OUTx SENSE as power outputs.
Recommended value for capacitors at VS:
Electrolytic capacitor C > 22µF in parallel with a ceramic capacitor C = 100nF.
Value for electrolytic capacitor depends on external loads, conducted interferences and reverse-conducting current
IHSX (see Section 4. “Absolute Maximum Ratings” on page 10).
ATA6836C [DATASHEET]
4952O–AUTO–02/15
17
11.
12.
Ordering Information
Extended Type Number
Package
Remarks
ATA6836C-TIQW
SO28
Pb-free, 2k, taped and reeled
ATA6836C-PXQW-1
QFN24
Pb-free, 6k, taped and reeled
Package Information
Figure 12-1. SO28
D
L
A
b
A2
A1
C
E1
E
e
28
15
technical drawings
according to DIN
specifications
Dimensions in mm
14
1
COMMON DIMENSIONS
Pin 1 identity
(Unit of Measure = mm)
Symbol
MIN
NOM
MAX
A
2.4
2.55
2.7
A1
A2
0.1
2.3
0.2
2.35
0.3
2.4
D
17.75
17.9
18.05
E
10.15
10.3
10.45
E1
7.4
7.5
7.6
L
0.6
0.8
1
C
0.22
0.27
0.32
b
e
0.32
0.4
0.48
NOTE
1.27 BSC
04/16/14
TITLE
Package Drawing Contact:
[email protected]
18
ATA6836C [DATASHEET]
4952O–AUTO–02/15
Package: SO28
300mil
GPC
DRAWING NO.
REV.
6.543-5184.01-4
1
Figure 12-2. QFN24
Top View
D
24
1
E
PIN 1 ID
technical drawings
according to DIN
specifications
6
A
Side View
A3
A1
Dimensions in mm
Bottom View
D2
7
12
13
COMMON DIMENSIONS
E2
6
1
Z
18
24
19
Z 10:1
L
e
b
(Unit of Measure = mm)
Symbol
MIN
NOM
MAX
A
0.8
0.85
0.9
A1
A3
0.0
0.16
0.035
0.21
0.05
0.26
D
4.9
5
5.1
D2
3.5
3.6
3.7
E
4.9
5
5.1
E2
3.5
3.6
3.7
L
0.35
0.4
0.45
b
e
0.2
0.25
0.65
0.3
NOTE
10/18/13
TITLE
Package Drawing Contact:
[email protected]
Package: VQFN_5x5_24L
Exposed pad 3.6x3.6
GPC
DRAWING NO.
REV.
6.543-5132.02-4
1
ATA6836C [DATASHEET]
4952O–AUTO–02/15
19
13.
Revision History
Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this
document.
Revision No.
4952O-AUTO-02/15
History
Section 11 “Ordering Information” on page 18 updated
Section 12 “Package Information” on pages 18 to 19 updated
4952N-AUTO-05/14
Section 7 “Electrical Characteristics” number 5.15 on page 13 updated
4952M-AUTO-04/14
Part datasheet in the latest template
4952L-AUTO-10/13
Part number ATA6836 removed from the datasheet
4952K-AUTO-03/12
Section 3.5 “Short-circuit Protection” on page 9 updated
4952J-AUTO-03/11
Section 10.1 “Application Notes” on page 17 updated
4952I-AUTO-08/10
Table 2-1 “Pin Description SO28” on page 4 updated
Ordering Information page 19 changed
4952H-AUTO-02/10
Section 7 “Electrical Characteristics” numbers 5.10 and 5.11 on page 13 updated
4952G-AUTO-12/09
Section 7 “Electrical Characteristics” number 1.2 on page 11 updated
Put datasheet in a new template
4952F-AUTO-07/09
Section 4 “Absolute Maximum Ratings” on page 10 updated
Section 7 “Electrical Characteristics” number 1.7 on page 11 updated
Features on page 1 updated
Table 2-1 “Pin Description SO28” on page 4 updated
Table 2-2 “Pin Description QFN24” on pages 5 to 6 updated
4952E-AUTO-10/08
Section 4 “Absolute Maximum Ratings” on page 10 updated
Section 6 “Operating Range” on page 10 updated
Section 7 “Electrical Characteristics” on pages 11 to 13 updated
Section 8 “Serial Interface: Timing” on page 14 updated
Section 9 “Noise and Surge Immunity” on page 16 updated
4952D-AUTO-10/07
4952C-AUTO-09/07
Section 11 “Ordering Information” on page 18 updated
Section 7 “Electrical Characteristics” numbers 5.15 and 5.16 on page 12 updated
Section 9 “Noise and Surge Immunity” on page 16 updated
Put datasheet in a new template
4952B-AUTO-07/07
20
ATA6836C [DATASHEET]
4952O–AUTO–02/15
Section 7 “Electrical Characteristics” numbers 1.5, 3.1, 5.15 and 8.2 on pages 11 to 13
updated
XXXXXX
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2015 Atmel Corporation. / Rev.: 4952O–AUTO–02/15
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and
other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.