Appendix A - ATtiny261A Specification at 125°C - Complete

Atmel 8-bit AVR Microcontroller with 2K
Bytes In-System Programmable Flash
ATtiny261A
Appendix A and B – ATtiny261A Specification at 105°C and 125°C
This document contains information specific to devices operating at temperatures up to
125°C. Only deviations are covered in this appendix, all other information can be found in
the complete datasheet. The complete datasheet can be found at www.atmel.com.
Rev. 8197E–AVR–11/2014
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
1. Electrical Characteristics
1.1
Absolute Maximum Ratings*
Operating Temperature ..................................-55C to +125C
*NOTICE:
Storage Temperature ......................................-65C to +150C
Voltage on any Pin except RESET
with respect to Ground ............................... -0.5V to VCC+0.5V
Voltage on RESET with respect to Ground ..... -0.5V to +13.0V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent
damage to the device. This is a stress rating
only and functional operation of the device at
these or other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Maximum Operating Voltage .............................................6.0V
DC Current per I/O Pin .................................................40.0mA
DC Current VCC and GND Pins..................................200.0mA
1.2
DC Characteristics
Table 1-1.
Symbol
VIL
VIH
DC Characteristics. TA = -40C to +125C, VCC = 1.8V to 5.5V (unless otherwise noted).
Parameter
Input Low-voltage
Input High-voltage
Condition
Min
Except XTAL1 and
RESET pins
Max
Units
-0.5
0.2VCC(3)
V
XTAL1 pin,
External Clock Selected
-0.5
0.1VCC(3)
V
RESET pin
-0.5
0.2VCC(3)
V
RESET pin as I/O
-0.5
0.2VCC(3)
V
Except XTAL1 and
RESET pins
0.7VCC(2)
VCC +0.5
V
XTAL1 pin,
External Clock Selected
0.8VCC(2)
VCC +0.5
V
RESET pin
0.9VCC(2)
VCC +0.5
V
(2)
VCC +0.5
V
0.6
0.5
V
V
RESET pin as I/O
(4)
Typ (1)
0.7VCC
VOL
Output Low Voltage
(Except Reset pin) (6)
IOL = 10mA, VCC = 5V
IOL = 5mA, VCC = 3V
VOH
Output High-voltage (5)
(Except Reset pin) (6)
IOH = -10mA, VCC = 5V
IOH = -5mA, VCC = 3V
IIL
Input Leakage
Current I/O Pin
VCC = 5.5V, pin low
(absolute value)
< 0.05
1
µA
IIH
Input Leakage
Current I/O Pin
VCC = 5.5V, pin high
(absolute value)
< 0.05
1
µA
RRST
Reset Pull-up Resistor
30
60
k
RPU
I/O Pin Pull-up Resistor
20
50
k
2
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
4.3
2.5
V
V
Table 1-1.
Symbol
DC Characteristics. TA = -40C to +125C, VCC = 1.8V to 5.5V (unless otherwise noted). (Continued)
Parameter
Power Supply Current (7)
ICC
Power-down mode (8)
Notes:
Typ (1)
Max
Units
Active 1MHz, VCC = 2V
0.2
0.5
mA
Active 4MHz, VCC = 3V
1.2
2
mA
Active 8MHz, VCC = 5V
3.6
7
mA
Idle 1MHz, VCC = 2V
0.035
0.15
mA
Idle 4MHz, VCC = 3V
0.25
0.4
mA
Idle 8MHz, VCC = 5V
0.9
1.5
mA
WDT enabled, VCC = 3V
4
20
µA
WDT disabled, VCC = 3V
0.2
10
µA
Condition
Min
1. Typical values at 25C.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. “Max” means the highest value where the pin is guaranteed to be read as low.
4. Although each I/O port can sink more than the test conditions (10mA at VCC = 5V, 5mA at VCC = 3V) under steady state
conditions (non-transient), the sum of all IOL (for all ports) should not exceed 60mA. If IOL exceeds the test conditions, VOL
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test condition.
5. Although each I/O port can source more than the test conditions (10mA at VCC = 5V, 5mA at VCC = 3V) under steady
state conditions (non-transient), the sum of all IOH (for all ports) should not exceed 60mA. If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current greater than the listed test
condition.
6. The RESET pin must tolerate high voltages when entering and operating in programming modes and, as a consequence,
has a weak drive strength as compared to regular I/O pins.
7. Values are with external clock. Power Reduction is enabled (PRR = 0xFF) and there is no I/O drive.
8. BOD Disabled.
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
3
1.3
Clock Characteristics
1.3.1
Accuracy of Calibrated Internal Oscillator
It is possible to manually calibrate the internal oscillator to be more accurate than default factory calibration.
Note:
Table 1-2.
The oscillator frequency depends on temperature and voltage. Voltage and temperature characteristics can be
found in Figure 2-42 on page 28 and Figure 2-43 on page 28.
Calibration Accuracy of Internal Oscillator
Calibration
Method
Target Frequency
VCC
Temperature
Accuracy at given
voltage & temperature (1)
8.0MHz
3V
25C
±10%
Fixed frequency
within:
7.3 – 8.1MHz
Fixed voltage within:
1.8V – 5.5V
Fixed temperature
within:
-40C to +125C
±1%
Factory
Calibration
User
Calibration
Notes:
1. Accuracy of oscillator frequency at calibration point (fixed temperature and fixed voltage).
1.4
System and Reset Characteristics
1.4.1
Enhanced Power-On Reset
Table 1-3.
Symbol
Characteristics of Enhanced Power-On Reset. TA = -40C to +125C
Parameter
(2)
Min(1)
Typ(1)
Max(1)
Units
1.1
1.4
1.7
V
1.3
1.7
V
VPOR
Release threshold of power-on reset
VPOA
Activation threshold of power-on reset (3)
0.6
SRON
Power-On Slope Rate
0.01
Note:
1. Values are guidelines, only.
2. Threshold where device is released from reset when voltage is rising.
3. The Power-on Reset will not work unless the supply voltage has been below VPOA.
4
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
V/ms
1.5
ADC Characteristics
Table 1-4.
Symbol
ADC Characteristics, Single Ended Channels. T = -40C to +125C
Parameter
Condition
Min
Typ
Resolution
Absolute accuracy
(Including INL, DNL, and
Quantization, Gain and Offset
Errors)
Max
Units
10
Bits
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
2
LSB
VREF = 4V, VCC = 4V,
ADC clock = 1 MHz
3
LSB
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
Noise Reduction Mode
1.5
LSB
VREF = 4V, VCC = 4V,
ADC clock = 1MHz
Noise Reduction Mode
2.5
LSB
Integral Non-Linearity (INL)
(Accuracy after Offset and
Gain Calibration)
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
1
LSB
Differential Non-linearity
(DNL)
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
0.5
LSB
Gain Error
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
2.5
LSB
Offset Error
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
1.5
LSB
Conversion Time
Free Running Conversion
13
260
µs
50
1000
kHz
VCC - 0.3
VCC + 0.3
V
Single Ended Conversions
2.0
AVCC
V
Differential Conversions
2.0
AVCC - 1.0
V
GND
VREF
0
AVCC (1)
Clock Frequency
AVCC
Analog Supply Voltage
AREF
External Voltage Reference
VIN
Input Voltage
Single Ended Conversions
Differential Conversions
Single Ended Conversions
38.5
Input Bandwidth
kHz
Differential Conversions
Internal 1.1V Reference
VINT
Internal 2.56V Reference
V
(1)
VCC > 3.0V
4
1.0
1.1
1.2
V
2.3
2.56
2.8
V
RREF
Reference Input Resistance
35
k
RAIN
Analog Input Resistance
100
M
ADC Conversion Output
Note:
0
1023
LSB
1. VDIFF must be below VREF.
2. Not tested in production.
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
5
1.6
Serial Programming Characteristics
Figure 1-1.
Serial Programming Waveforms
SERIAL DATA INPUT
(MOSI)
MSB
LSB
SERIAL DATA OUTPUT
(MISO)
MSB
LSB
SERIAL CLOCK INPUT
(SCK)
SAMPLE
Figure 1-2.
Serial Programming Timing
MOSI
tSHOX
tOVSH
SCK
tSLSH
tSHSL
MISO
tSLIV
Table 1-5.
Symbol
Parameter
1/tCLCL
Oscillator Frequency
tCLCL
Oscillator Period
1/tCLCL
tCLCL
tSHSL
Min
0
Max
Units
4
MHz
250
Oscillator Frequency (VCC = 4.5V - 5.5V)
0
Oscillator Period VCC = 4.5V - 5.5V
50
SCK Pulse Width High
Typ
ns
20
MHz
ns
2 tCLCL
(1)
ns
2 tCLCL
(1)
ns
tSLSH
SCK Pulse Width Low
tOVSH
MOSI Setup to SCK High
tCLCL
ns
tSHOX
MOSI Hold after SCK High
2 tCLCL
ns
tSLIV
SCK Low to MISO Valid
Note:
6
Serial Programming Characteristics, TA = -40C to +125C, VCC = 1.8 - 5.5V (Unless Otherwise
Noted)
1. 2 tCLCL for fck < 12MHz, 3 tCLCL for fck >= 12MHz
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
100
ns
2. Typical Characteristics
The data contained in this section is largely based on simulations and characterization of similar devices in the
same process and design methods. Thus, the data should be treated as indications of how the part will behave.
The following charts show typical behavior. These figures are not tested during manufacturing. During characterisation devices are operated at frequencies higher than test limits but they are not guaranteed to function
properly at frequencies higher than the ordering code indicates.
This device has been characterised at temperatures of -40C, 25C, 85C and 125C.
All current consumption measurements are performed with all I/O pins configured as inputs and with internal
pull-ups enabled. Current consumption is a function of several factors such as operating voltage, operating frequency, loading of I/O pins, switching rate of I/O pins, code executed, and ambient temperature. The dominating
factors are operating voltage and frequency.
A sine wave generator with rail-to-rail output is used as clock source but current consumption in Power-Down
mode is independent of clock selection. The difference between current consumption in Power-Down mode with
Watchdog Timer enabled and Power-Down mode with Watchdog Timer disabled represents the differential current drawn by the Watchdog Timer.
The current drawn from pins with a capacitive load may be estimated (for one pin) as follows:
I CP  V CC  C L  f SW
where VCC = operating voltage, CL = load capacitance and fSW = average switching frequency of I/O pin.
Current Consumption in Active Mode
Figure 2-1.
Active Supply Current vs. VCC (Internal Calibrated Oscillator, 8MHz)
5
125 °C
85 °C
25 °C
-40 °C
4
3
ICC (mA)
2.1
2
1
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
7
Figure 2-2.
Active Supply Current vs. VCC (Internal Calibrated Oscillator, 1MHz)
1,2
125 °C
85 °C
25 °C
-40 °C
1
ICC (mA)
0,8
0,6
0,4
0,2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 2-3.
Active Supply Current vs. VCC (Internal Calibrated Oscillator, 128kHz)
0,12
-40 °C
125 °C
25 °C
85 °C
0,1
ICC (mA)
0,08
0,06
0,04
0,02
0
1,5
2
2,5
3
3,5
VCC (V)
8
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
4
4,5
5
5,5
Current Consumption in Idle Mode
Figure 2-4.
Idle Supply Current vs. VCC (Internal Calibrated Oscillator, 8MHz)
1,4
125 °C
85 °C
25 °C
-40 °C
1,2
ICC (mA)
1
0,8
0,6
0,4
0,2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 2-5.
Idle Supply Current vs. VCC (Internal Calibrated Oscillator, 1MHz)
0,35
125 °C
85 °C
25 °C
-40 °C
0,3
0,25
ICC (mA)
2.2
0,2
0,15
0,1
0,05
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
9
Figure 2-6.
Idle Supply Current vs. VCC (Internal Calibrated Oscillator, 128kHz)
0,025
125 °C
-40 °C
25 °C
85 °C
ICC (mA)
0,02
0,015
0,01
0,005
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
2.3
Current Consumption in Power-Down Mode
Figure 2-7.
Power-down Supply Current vs. VCC (Watchdog Timer Disabled)
3
125 °C
2,5
ICC (uA)
2
1,5
1
85 °C
0,5
25 °C
-40 °C
0
1,5
2
2,5
3
3,5
VCC (V)
10
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
4
4,5
5
5,5
Figure 2-8.
Power-down Supply Current vs. VCC (Watchdog Timer Enabled)
12
125 °C
10
ICC (uA)
8
-40 °C
25 °C
85 °C
6
4
2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Current Consumption of Peripheral Units
Figure 2-9.
Brownout Detector Current vs. VCC
40
35
30
125 °C
85 °C
25 °C
-40 °C
25
ICC (uA)
2.4
20
15
10
5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
11
Figure 2-10. Programming Current vs. VCC
9000
-40 °C
8000
7000
25 °C
ICC (uA)
6000
5000
85 °C
4000
125 °C
3000
2000
1000
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
2.5
Pull-up Resistors
Figure 2-11. Pull-Up Resistor Current vs. Input Voltage (I/O Pin, VCC = 1.8V)
60
50
IOP (uA)
40
30
20
10
25 °C
85 °C
-40 °C
125 °C
0
0
0,2
0,4
0,6
0,8
1
VOP (V)
12
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
1,2
1,4
1,6
1,8
2
Figure 2-12. Pull-Up Resistor Current vs. Input Voltage (I/O Pin, VCC = 2.7V)
90
80
70
IOP (uA)
60
50
40
30
20
25 °C
85 °C
-40 °C
125 °C
10
0
0
0,5
1
1,5
2
2,5
3
VOP (V)
Figure 2-13. Pull-Up Resistor Current vs. Input Voltage (I/O Pin, VCC = 5V)
160
140
120
IOP (uA)
100
80
60
40
25 °C
85 °C
-40 °C
125 °C
20
0
0
1
2
3
4
5
6
VOP (V)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
13
Figure 2-14. Pull-Up Resistor Current vs. Input Voltage (Reset Pin, VCC = 1.8V)
40
35
IRESET (uA)
30
25
20
15
10
25 °C
-40 °C
85 °C
125 °C
5
0
0
0,2
0,4
0,6
0,8
1
1,2
1,4
1,6
1,8
2
VRESET (V)
Figure 2-15. Pull-Up Resistor Current vs. Input Voltage (Reset Pin, VCC = 2.7V)
60
50
IRESET (uA)
40
30
20
10
25 °C
-40 °C
85 °C
125 °C
0
0
0,5
1
1,5
VRESET (V)
14
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
2
2,5
3
Figure 2-16. Pull-Up Resistor Current vs. Input Voltage (Reset Pin, VCC = 5V)
120
100
IRESET (uA)
80
60
40
20
25 °C
-40 °C
85 °C
125 °C
0
0
0,5
1
1,5
2
2,5
3
3,5
4
4,5
5
VRESET (V)
Output Driver Strength
Figure 2-17. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 1.8V)
0,4
125 °C
0,35
85 °C
0,3
25 °C
0,25
VOL (V)
2.6
-40 °C
0,2
0,15
0,1
0,05
0
0
1
2
3
4
5
IOL (mA)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
15
Figure 2-18. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 3V)
0,5
125 °C
0,4
85 °C
25 °C
VOL (V)
0,3
-40 °C
0,2
0,1
0
0
2
4
6
8
10
IOL (mA)
Figure 2-19. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 5V)
0,7
125 °C
0,6
VOL (V)
85 °C
0,5
25 °C
0,4
-40 °C
0,3
0,2
0,1
0
0
2
4
6
8
10
IOL (mA)
16
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
12
14
16
18
20
Figure 2-20. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 1.8V)
1,8
1,7
VOH (V)
1,6
1,5
-40 °C
25 °C
1,4
85 °C
125 °C
1,3
0
1
2
3
4
5
IOH (mA)
Figure 2-21. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 3V)
3
2,9
VOH (V)
2,8
2,7
-40 °C
25 °C
2,6
85 °C
125 °C
2,5
0
2
4
6
8
10
IOH (mA)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
17
Figure 2-22. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 5V)
5
VOH (V)
4,8
4,6
-40 °C
25 °C
4,4
85 °C
125 °C
4,2
0
5
10
15
20
IOH (mA)
Figure 2-23. VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 1.8V)
0,8
VOL (V)
0,6
0,4
125 °C
85 °C
25 °C
-40 °C
0,2
0
0
0,1
0,2
0,3
IOL (mA)
18
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
0,4
0,5
0,6
Figure 2-24. VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 3V)
0,8
VOL (V)
0,6
0,4
125 °C
85 °C
25 °C
0,2
-40 °C
0
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
IOL (mA)
Figure 2-25. VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 5V)
0,8
VOL (V)
0,6
0,4
0,2
125 °C
85 °C
25 °C
-40 °C
0
0
0,1
0,2
0,3
0,4
0,5
0,6
0,7
0,8
IOL (mA)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
19
Figure 2-26. VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 1.8V)
5
4
VOH (V)
3
2
1
-40 °C
25 °C
85 °C
125 °C
0
0
0,2
0,4
0,6
0,8
1
IOH (mA)
Figure 2-27. VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 3V)
5
4
VOH (V)
3
2
-40 °C
25 °C
85 °C
125 °C
1
0
0
0,2
0,4
0,6
IOH (mA)
20
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
0,8
1
Figure 2-28. VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 5V)
5
4
125 °C
85 °C
25 °C
-40 °C
VOH (V)
3
2
1
0
0
0,2
0,4
0,6
0,8
1
IOH (mA)
Input Thresholds and Hysteresis
Figure 2-29. VIH: Input Threshold Voltage vs. VCC (I/O Pin, Read as ‘1’)
3,5
3
125 °C
85 °C
25 °C
-40 °C
2,5
Threshold (V)
2.7
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
21
Figure 2-30. VIL: Input Threshold Voltage vs. VCC (I/O Pin, Read as ‘0’)
3
125 °C
85 °C
25 °C
-40 °C
2,5
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
4
4,5
5
5,5
VCC (V)
Figure 2-31. VIH-VIL: Input Hysteresis vs. VCC (I/O Pin)
0,6
-40 °C
Input Hysteresis (V)
0,5
25 °C
0,4
85 °C
0,3
125 °C
0,2
0,1
0
1,5
2
2,5
3
3,5
VCC (V)
22
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
Figure 2-32. VIH: Input Threshold Voltage vs. VCC (Reset Pin, Read as ‘1’)
2,5
Threshold (V)
2
1,5
-40 °C
1
25 °C
85 °C
125 °C
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 2-33. VIL: Input Threshold Voltage vs. VCC (Reset Pin, Read as ‘0’)
2,5
125 °C
85 °C
25 °C
-40 °C
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
23
Figure 2-34. VIH-VIL: Input Hysteresis vs. VCC (Reset Pin)
1
0,9
0,8
Input Hysteresis (V)
0,7
-40 °C
0,6
0,5
25 °C
0,4
85 °C
0,3
0,2
125 °C
0,1
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
2.8
BOD, Bandgap and Reset
Figure 2-35. BOD Threshold vs. Temperature (BOD Level set to 4.3V)
4,38
4,36
Threshold (V)
4,34
VCC RISING
4,32
4,3
4,28
4,26
VCC FALLING
4,24
-40
-20
0
20
40
60
Temperature (C)
24
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
80
100
120
140
Figure 2-36. BOD Threshold vs. Temperature (BOD Level set to 2.7V)
2,78
2,76
VCC RISING
Threshold (V)
2,74
2,72
2,7
2,68
VCC FALLING
2,66
-40
-20
0
20
40
60
80
100
120
140
Temperature (C)
Figure 2-37. BOD Threshold vs. Temperature (BOD Level set to 1.8V)
1,85
1,84
Threshold (V)
1,83
1,82
VCC RISING
1,81
1,8
1,79
VCC FALLING
1,78
-40
-20
0
20
40
60
80
100
120
140
Temperature (C)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
25
Figure 2-38. Bandgap Voltage vs. Supply Voltage.
1,11
Bandgap Voltage (V)
1,1
85 °C
125 °C
25 °C
1,09
1,08
-40 °C
1,07
1,5
2,5
3,5
4,5
5,5
VCC (V)
Figure 2-39. Minimum Reset Pulse Width vs. VCC
1800
1600
1400
Pulsewidth (ns)
1200
1000
800
600
400
125 °C
85 °C
25 °C
-40 °C
200
0
1,5
2
2,5
3
3,5
VCC (V)
26
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
4
4,5
5
5,5
Internal Oscillators
Figure 2-40. Frequency of Watchdog Oscillator vs. VCC
130000
Frequency (Hz)
125000
-40 °C
120000
25 °C
85 °C
115000
125 °C
110000
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 2-41. Frequency of Watchdog Oscillator vs. Temperature
130000
125000
Frequency (kHz)
2.9
120000
1.8 V
115000
3.0 V
5.0 V
110000
-40
-20
0
20
40
60
80
100
120
140
Temperature
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
27
Figure 2-42. Frequency of Calibrated 8.0MHz Oscillator vs. VCC
8,4
-40 °C
25 °C
8,2
Frequency (MHz)
85 °C
125 °C
8
7,8
7,6
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 2-43. Frequency of Calibrated 8.0MHz Oscillator vs. Temperature
8,2
Frequency (MHz)
8,1
8
5.0 V
7,9
3.0 V
7,8
1.8 V
7,7
-40
-20
0
20
40
60
Temperature
28
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
80
100
120
140
Figure 2-44. Frequency of Calibrated 8.0MHz Oscillator vs. OSCCAL Value
16
-40 °C
25 °C
85 °C
125 °C
14
12
FRC (MHz)
10
8
6
4
2
0
0
16
32
48
64
80
96
112
128
144
160
176
192
208
224
240
OSCCAL (X1)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
29
3. Ordering Information
Speed (MHz)
Power Supply
Ordering Code (1)
20
1.8 – 5.5V
ATtiny261A-MN
ATtiny261A-MNR(2)
32M1-A
Industrial
(-40C to +105C)
20
1.8 – 5.5V
ATtiny261A-MF
ATtiny261A-MFR(2)
32M1-A
Industrial
(-40C to +125C)
Notes:
Package (1)
Operational Range
1. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
halide-free and fully green.
2. Tape & Reel.
Package Type
32M1-A
30
32-pad, 5 x 5 x 1.0mm Body, Lead Pitch 0.50mm, Micro Lead Frame Package (MLF)
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
4. Revision History
Revision No.
History
8197E–Appendix A–AVR–10/2014
Updated operating temperatures from 105C to 125C.
Updated information at the last page.
Added Ordering Information for Operating range (-40C to +125C)
8197D–Appendix A–AVR–02/2013
Updated ordering codes.
Updated contact information at the last page.
8197C–Appendix A–AVR–08/2011
Updated contact information.
8197A–Appendix A–AVR–06/2010
Initial revision.
ATtiny261A [PRELIMINARY DATASHEET]
Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014
31
XXXXXX
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2014 Atmel Corporation. / Rev.: Atmel-8197E-AVR-ATtiny261A-Specification-at-105°C-and-125°C-Datasheet_11/2014.
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and
other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.