AT34C04 - Complete

AT34C04
I2C-Compatible 4-Kbit Serial EEPROM
with Reversible Software Write Protection
DATASHEET
Features
 Single 1.7V to 3.6V VCC Supply
 JEDEC JC42.4 (EE1004-v) Serial Presence Detect (SPD) Compliant
 2-wire Serial Interface: I2C Fast-Mode Plus (FM+)™ Compatible
̶
100kHz, 400kHz, and 1MHz Compatibility
Bus Timeout Supported
̶
 Advanced Software Data Protection Features
̶
Individually reversible software write protection on all four 128-byte quadrants
Software procedure to verify each quadrant’s write protection status
̶
 16-byte Page Write Mode
̶
Partial Page Writes Allowed
 Self-timed Write Cycle (5ms Maximum)
 Schmitt Trigger, Filtered Inputs for Noise Suppression
 High-reliability
̶
Endurance: 1,000,000 Write Cycles
Data Retention: 100 Years
̶
 Low Operating Current
̶
Write ~1.5mA (Typical)
Read ~ 0.2mA (Typical)
̶
 Green Packaging Options (Pb/Halide-free/RoHS Compliant)
̶
8-lead JEDEC SOIC, 8-lead TSSOP, and 8-pad UDFN
Description
The Atmel® AT34C04 is a 1.7V rated minimum operating voltage Serial EEPROM
device containing 4096-bits of Serially Electrically Erasable and Programmable ReadOnly Memory (EEPROM) organized as 512-bytes of eight bits each. The Serial
EEPROM operation is tailored specifically for DRAM memory modules with Serial
Presence Detect (SPD) to store a module’s vital product data such as the module’s
size, speed, voltage, data width, and timing parameters.
The AT34C04 is protocol compatible with the legacy JEDEC EE1002 specification
(2-Kbit) devices enabling the AT34C04 to be utilized in legacy applications without any
software changes. The device is designed to respond to specific software commands
that allow users to identify and set which half of the memory the internal address
counter is located. This special page addressing method to select the upper or lower
half of the Serial EEPROM is what facilitates legacy compatibility. However, there is
one exception to the legacy compatibility as the AT34C04 does not support the
Permanent Write Protection feature.
Additionally, the AT34C04 incorporates a Reversible Software Write Protection
(RSWP) feature enabling the capability to selectively write protect any or all of the four
128-byte quadrants. Once the RSWP is set, it can only be reversed by sending a
specific software command sequence.
The AT34C04 supports the industry standard 2-wire I2C Fast-Mode Plus (FM+) serial
interface allowing device communication to operate at up to 1MHz. A bus timeout
feature is supported to help prevent system lock-ups. The AT34C04 is available in
space saving SOIC, TSSOP, and UDFN packages.
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
T a b l e o f C o n te n ts
1.
Pin Descriptions and Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.
Device Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
Start Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stop Condition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acknowledge (ACK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No-Acknowledge (NACK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Reset and Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timeout Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-wire Software Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
6
6
6
7
8
8
4.
Device Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1
5.2
5.3
6.
Read and Write Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1
6.2
6.3
7.
13
13
15
15
15
16
17
17
18
19
19
Set RSWP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Clear RSWP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Read RSWP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Part Marking Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.1
9.
Memory Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.1
Set Page Address and Read Page Address Commands . . . . . . . . . . . . . . . . . . . . . . . . .
Read Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.1
Current Address Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.2
Random Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.3
Sequential Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.1
Byte Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.2
Page Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.3
Acknowledge (ACK) Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.4
Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.1
7.2
7.3
8.
Absolute Maximum Ratings* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Part Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Ordering Code Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
10. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
11. Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
11.1
11.2
11.3
8S1 — 8-lead JEDEC SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8X — 8-lead TSSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8MA2 — 8-pad UDFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
12. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
1.
Pin Descriptions and Pinouts
Table 1-1.
Pin Descriptions
Symbol
Name and Function
No Connect: The NC pin is not bonded to a die pad. This pin can be connected
to GND or left floating.
NC
Device Address Inputs: The A0, A1, and A2 pins are used to select the device
address and corresponds to the three Least-Significant Bits (LSBs) of the I2C
FM+ seven bit slave address. These pins can be directly connected to VCC or
GND in any combination, allowing up to eight devices on the same bus.
A0, A1, A2
Asserted
State
Type
—
—
—
Input
—
Power
—
Input/
Output
—
Input
—
Power
The A0 pin is also an overvoltage tolerant pin, allowing up to 10V to support the
Reversible Software Write Protection (RSWP) feature (see Section 7.).
Ground: The ground reference for the power supply. GND should be connected
to the system ground.
GND
Serial Data: The SDA pin is an open-drain bidirectional input/output pin used to
serially transfer data to and from the device.
SDA
The SDA pin must be pulled-high using an external pull-up resistor (not to
exceed 8K in value) and may be wire-ORed with any number of other
open-drain or open-collector pins from other devices on the same bus.
Serial Clock: The SCL pin is used to provide a clock to the device and is used
to control the flow of data to and from the device. Command and input data
present on the SDA pin is always latched in on the rising edge of SCL, while
output data on the SDA pin is always clocked out on the falling edge of SCL.
SCL
The SCL pin must either be forced high when the serial bus is idle or pulled-high
using an external pull-up resistor.
Device Power Supply: The VCC pin is used to supply the source voltage to the
device. Operations at invalid VCC voltages may produce spurious results and
should not be attempted.
VCC
Figure 1-1.
Pinouts
A0
1
8
VCC
A1
2
7
NC
A2
3
6
SCL
GND
4
5
SDA
Top View
Note:
(1)
8-pad UDFN
8-lead TSSOP
8-lead SOIC
A0
A1
A2
GND
1
2
3
4
8
7
6
5
Top View
VCC
NC
SCL
SDA
A0
A1
A2
GND
1
2
3
4
8
7
6
5
VCC
NC
SCL
SDA
Top View
1. The metal pad on the bottom of the UDFN package is not internally connected to a voltage
potential. This pad can be a “no connect” or connected to GND.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
3
2.
Block Diagram
A0
Hardware
Address
Comparator
Memory
System Control
Module
Power
On Reset
Generator
VCC
High Voltage
Generation Circuit
Quadrant 1
4-Kbit EEPROM Array
Quadrant 2
Row Decoder
Quadrant 0
A1
Quadrant 3
Software Write
Protection
Control
Address Register
and Counter
1 page
Column Decoder
A2
SCL
Data Register
Data & ACK
DOUT Input/Output Control
GND
4
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
DIN
Start
Stop
Detector
SDA
3.
Device Communication
The AT34C04 operates as a slave device and utilizes a simple 2-wire digital serial interface, compatible with the
I2C Fast-Mode Plus (I2C FM+) protocol, to communicate with a host controller, commonly referred to as the bus
Master. The Master initiates and controls all Read and Write operations to the slave devices on the serial bus,
and both the Master and the slave devices can transmit and receive data on the bus.
The serial interface is comprised of just two signal lines: the Serial Clock (SCL) and the Serial Data (SDA). The
SCL pin is used to receive the clock signal from the Master, while the bidirectional SDA pin is used to receive
command and data information from the Master, as well as, to send data back to the Master. Data is always
latched into the AT34C04 on the rising edge of SCL and is always output from the device on the falling edge of
SCL. Both the SCL and SDA pin incorporate integrated spike suppression filters and Schmitt Triggers to
minimize the effects of input spikes and bus noise.
All command and data information is transferred with the Most-Significant Bit (MSB) first. During the bus
communication, one data bit is transmitted every clock cycle, and after eight bits (one byte) of data has been
transferred, the receiving device must respond with either an acknowledge (ACK) or a no-acknowledge (NACK)
response bit during a ninth clock cycle (ACK/NACK clock cycle) generated by the Master. Therefore, nine clock
cycles are required for every one byte of data transferred. There are no unused clock cycles during any Read or
Write operation so there must not be any interruptions or breaks in the data stream during each data byte
transfer and ACK or NACK clock cycle.
During data transfers, data on the SDA pin must only change while SCL is low, and the data must remain stable
while SCL is high. If data on the SDA pin changes while SCL is high, then either a Start or a Stop condition will
occur. Start and Stop conditions are used to initiate and end all serial bus communication between the Master
and the slave devices.The number of data bytes transferred between a Start and a Stop condition is not limited
and is determined by the Master.
In order for the serial bus to be idle, both the SCL and SDA pins must be in the Logic 1 state at the same time.
3.1
Start Condition
A Start condition occurs when there is a high-to-low transition on the SDA pin while the SCL pin is stable in the
Logic 1 state. The Master uses a Start condition to initiate any data transfer sequence, therefore the Start
condition must precede any command. The AT34C04 will continuously monitor the SDA and SCL pins for a
Start condition, and the device will not respond unless one is given. Please refer to Figure 3-1 on page 6 for
more details.
3.2
Stop Condition
A Stop condition occurs when there is a low-to-high transition on the SDA pin while the SCL pin is stable in the
Logic 1 state. The Master uses the Stop condition to end a data transfer sequence to the AT34C04 which will
subsequently return to the idle state. The Master can also utilize a repeated Start condition instead of a Stop
condition to end the current data transfer if the Master will perform another operation. Please refer to Figure 3-1
on page 6 for more details.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
5
3.3
Acknowledge (ACK)
After every byte of data is received, the AT34C04 must acknowledge to the Master that it has successfully
received the data byte by responding with an ACK. This is accomplished by the Master first releasing the SDA
line and providing the ACK/NACK clock cycle (a ninth clock cycle for every byte). During the ACK/NACK clock
cycle, the AT34C04 must output a Logic 0 (ACK) for the entire clock cycle such that the SDA line must be stable
in the Logic 0 state during the entire high period of the clock cycle. Please refer to Figure 3-1 on page 6 for more
details.
3.4
No-Acknowledge (NACK)
When the AT34C04 is transmitting data to the Master, the Master can indicate that it is done receiving data and
wants to end the operation by sending a NACK response to the AT34C04 instead of an ACK response. This is
accomplished by the Master outputting a Logic 1 during the ACK/NACK clock cycle, at which point the AT34C04
will release the SDA line so that the Master can then generate a Stop condition.
In addition, the AT34C04 can use a NACK to respond to the Master instead of an ACK for certain invalid
operation cases such as an attempt to Write to a read-only register.
Figure 3-1.
Start, Stop, and ACK
SCL
SDA
Must Be
Stable
SDA
Must Be
Stable
1
2
Acknowledge Window
8
9
Stop
Condition
SDA
Acknowledge
Valid
Start
Condition
SDA
Change
Allowed
3.5
SDA
Change
Allowed
The transmitting device (Master or Slave)
must release the SDA line at this point to allow
the receiving device (Master or Slave) to drive the
SDA line low to ACK the previous 8-bit word.
Standby Mode
The AT34C04 incorporates a low-power Standby mode which is enabled:


6
Upon power-up or
After the receipt of a Stop condition and the completion of any internal operations.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
The receiver (Master or Slave)
must release the SDA line at
this point to allow the transmitter
to continue sending new data.
3.6
Device Reset and Initialization
The AT34C04 incorporates an internal Power-On Reset (POR) circuit to help prevent inadvertent operations
during power-up and power down cycles. On a cold power-up, the supply voltage must rise monotonically
between VPOR(max) and VCC(min) without any ring back to ensure a proper power-up (see Figure 3-2). Once the
supply voltage has passed the VPOR(min) threshold, the device internal reset process is initiated. Completion of
the internal reset process occurs within the tINIT time listed in Table 3-1.
Before selecting the device and issuing protocol, a valid and stable supply voltage must be applied and no
protocol should be issued to the device for the time specified by the tINIT parameter. The supply voltage must
remain stable and valid until the end of the protocol transmission, and for a Write instruction, until the end of the
internal write cycle.
Figure 3-2.
VCC
Power-up Timing
Cold
Power-On Reset
Warm
Power-On Reset
tINIT
Device Access
Permitted
VCC (min)
tPOR
VPOR (max)
VPOR (min)
Do Not Attempt
Device Access
During This Time
tPOFF
Time
Table 3-1.
Symbol
Power-up Conditions
Parameter
Min
Max
Units
10.0
ms
1.6
V
tPOR
Power-On Reset Time
VPOR
Power-On Reset Voltage Range
1.0
tINIT
Time from Power-On to First Command
10.0
ms
tPOFF
Warm Power Cycle Off Time
1.0
ms
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
7
3.7
Timeout Function
The AT34C04 supports the industry standard bus Timeout feature to help prevent potential system bus hangups. The device resets its serial interface and will stop driving the bus (will let SDA float high) if the SCL pin is
held low for more than the minimum Timeout (tOUT) specification. The AT34C04 will be ready to accept a new
Start condition before the maximum tOUT has elapsed (see Figure 3-3). This feature does require a minimum
SCL clock speed of 10kHz to avoid any timeout issues.
Figure 3-3.
Timeout
tTIMEOUT (MAX)
tTIMEOUT (MIN)
SCL
Device will release Bus and
be ready to accept a new
Start Condition within this Time
3.8
2-wire Software Reset
After an interruption in protocol, power loss, or system reset, any 2-wire part can be reset by following these
steps:
1.
Create a Start condition.
2.
3.
Clock nine cycles.
Create another Start condition followed by Stop condition as shown in Figure 3-4.
Figure 3-4.
2-wire Software Reset
Dummy Clock Cycles
SCL
1
Start
Condition
SDA
8
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
2
3
8
9
Start
Condition
Stop
Condition
4.
Device Addressing
The AT34C04 requires a 7-bit device address and a Read/Write select bit following a Start condition from the
Master to initiate communication with the Serial EEPROM. The device address byte is comprised of a 4-bit
device type identifier followed by three device address bits (A2, A1, and A0) and a R/W bit and is clocked by the
Master on the SDA pin with the most significant bit first (see Table 4-1).
The AT34C04 will respond to two unique device type identifiers. The device type identifier of ‘1010’(Ah) is
necessary to select the device for reading or writing. The device type identifier of ‘0110’(6h) has multiple
purposes. First, it is used to access the page address function which determines what the internal address
counter is set to. For more information on accessing the page address function, please refer to Section 6.1.1.
The device type identifier of ‘0110’(6h) is also used to access the software write protection feature of the
device. Information on the software write protection functionality can be found in Section 7.
Table 4-1.
AT34C04 Device Address Byte
Bit 7
Function
Bit 6
Bit 5
Bit 4
Bit 3
Device Type Identifier
Bit 2
Bit 1
Device Address
Bit 0
Read/Write
EEPROM Read/Write
1
0
1
0
A2
A1
A0
R/W
Write Protection and
Page Address Functions
0
1
1
0
A2
A1
A0
R/W
The software device address bits (A2, A1, and A0) must match their corresponding hard-wired device address
inputs (A2, A1 and A0) allowing up to eight devices on the bus at the same time (see Table 4-2). The eighth bit of
the address byte is the R/W operation selection bit. A read operation is selected if this bit is a Logic 1, and a
Write operation is selected if this bit is a Logic 0. Upon a compare of the device address byte, the AT34C04 will
output an ACK during the ninth clock cycle; if a compare is not true, the device will output a NACK during the
ninth clock cycle and return the device to the low-power Standby Mode.
Table 4-2.
Device Address Combinations
Software Device
Address Bits
Hard-wired Device Address Inputs
A2, A1, A0
A2
A1
A0
000
GND
GND
GND
001
GND
GND
VCC
010
GND
VCC
GND
011
GND
VCC
VCC
100
VCC
GND
GND
101
VCC
GND
VCC
110
VCC
VCC
GND
111
VCC
VCC
VCC
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
9
5.
Electrical Specifications
5.1
Absolute Maximum Ratings*
Temperature under Bias. . . . . . . . . . .-40°C to +125°C
Storage Temperature . . . . . . . . . . . .-65°C to +150°C
Supply voltage
with respect to ground . . . . . . . . . . . . . -0.5V to +4.3V
All other input voltages
with respect to ground . . . . . . . . . -0.5V to VCC + 0.5V
All input voltages
with respect to ground . . . . . . . . . -0.5V to VCC + 0.5V
5.2
*Notice: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage
to the device. Functional operation of the device at
these ratings or any other conditions beyond those
indicated in the operational sections of this
specification is not implied. Exposure to absolute
maximum rating conditions for extended periods
may affect device reliability. Voltage extremes
referenced in the “Absolute Maximum Ratings” are
intended to accommodate short duration
undershoot/overshoot conditions and does not
imply or guarantee functional device operation at
these levels for any extended period of time.
DC Characteristics
Table 5-1.
DC Characteristics
Applicable over recommended operating range: TA = –20°C to +125°C, VCC = 1.7V to 3.6V (unless otherwise noted).
Symbol
Parameter
VCC
Supply Voltage
ICC1
Supply Current
VCC = 3.6V
Read at 100kHz
ICC2
Supply Current
VCC = 3.6V
ISB
Standby Current
ILI
Input Leakage Current
ILO
Output Leakage Current
VIL
Input Low Level(1)
VIH
Input High Level(1)
VOL1
Low-Level Output Voltage
Open-Drain
VOL2
IOL
Min
Typ
Max
Units
3.6
V
0.4
1.0
mA
Write at 100kHz
1.5
3.0
mA
VCC = 1.7V
VIN = VCC or VSS
1.6
3.0
μA
VCC = 3.6V
VIN = VCC or VSS
1.6
4.0
μA
VIN = VCC or VSS
0.1
2.0
μA
VOUT = VCC or VSS
0.1
2.0
μA
-0.5
0.3 * VCC
V
0.7 * VCC
VCC + 0.5
V
1.7
VCC > 2V
IOL = 3mA
0.4
V
VCC ≤ 2V
IOL = 2mA
0.2 * VCC
V
VOL = 0.4V
Freq ≤ 400kHz
3.0
mA
VOL = 0.6V
Freq ≤ 400kHz
6.0
mA
VOL = 0.4V
Freq > 400kHz
20.0
mA
VHV
A0 Pin High Voltage
VHYST1
Input Hysteresis (SDA, SCL)
VCC < 2V
0.10 * VCC
V
VHYST2
Input Hysteresis (SDA, SCL)
VCC ≥ 2V
0.05 * VCC
V
Note:
10
Low-Level Output Current
Test Condition
1.
VHV - VCC ≥ 4.8V
VIL min and VIH max are reference only and are not tested.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
7
10
V
5.3
AC Characteristics
Table 5-2.
AC Characteristics
Applicable over recommended operating range: TA = –20°C to +125°C, VCC = 1.7V to 3.6V, CL = 1 TTL Gate and 100μF
(unless otherwise noted).
VCC < 2.2V
100kHz
VCC ≥ 2.2V
400kHz
1000kHz
Symbol
Parameter
Min
Max
Min
Max
Min
Max
Units
fSCL
Clock Frequency, SCL
10(2)
100
10(2)
400
10(2)
1,000
kHz
tLOW
Clock Pulse Width Low
4,700
1,300
500
ns
tHIGH
Clock Pulse Width High
4,000
600
260
ns
tI
Noise Suppression Time
tBUF
Time the bus must be free before
a new transmission can start(1)
4,700
1,300
500
ns
tHD.STA
Start Hold Time
4,000
600
260
ns
tSU.STA
Start Set-up Time
4,700
600
260
ns
tHD.DI
Data In Hold Time
0.0
0.0
0.0
ns
tSU.DAT
Data In Set-up Time
250
100
50
ns
tR
Inputs Rise Time(1)
(1)
tF
Inputs Fall Time
tSU.STO
Stop Set-up Time
tHD.DAT
Data Out Hold Time
tWR
Write Cycle Time
tOUT
Timeout Time
Endurance
25°C, Page Mode(1)
Notes:
1.
2.
50
ns
20
300
120
ns
300
20
300
120
ns
600
3,450
200
5
25
50
1,000
4,000
200
50
35
260
900
0
5
25
35
25
1,000,000
ns
350
ns
5
ms
35
ms
Write Cycles
This parameter is ensured by characterization only.
The minimum frequency is specified at 10kHz to avoid activating the timeout feature.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
11
Figure 5-1.
Bus Timing
SCL: Serial Clock, SDA: Serial Data I/O
tF
tHIGH
tR
tLOW
SCL
tSU.STA
tHD.STA
tLOW
tHD.DAT
tSU.DAT
tSU.STO
SDA
tBUF
Table 5-3.
Pin Capacitance(1)
Applicable over recommended operating range from TA = 25°C, f = 1 MHz, VCC = 1.7V - 3.6V.
Symbol
Test condition
CI/O
CIN
Note:
12
1.
Max
Units
Conditions
Input/output capacitance (SDA)
8
pF
VI/O = 0V
Input capacitance (A0, A1, A2, SCL)
6
pF
VIN = 0V
This parameter is ensured by characterization only.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
6.
Read and Write Operations
6.1
Memory Organization
To provide the greatest flexibility and backwards compatibility with the previous generations of SPD devices, the
AT34C04 memory organization is organized into two independent 2-Kbit memory arrays. Each 2-Kbit (256-byte)
section is internally organized into two independent quadrants of 128 bytes with each quadrant comprised of
eight pages of 16 bytes. Including both memory sections, there are four 128-byte quadrants totaling 512 bytes.
The memory array organization details are shown in Section 2. on page 4 and Table 6-1.
6.1.1
Set Page Address and Read Page Address Commands
The AT34C04 incorporates an innovative memory addressing technique that utilizes a Set Page Address (SPA)
and Read Page Address (RPA) commands to select and verify the desired half of the memory enabled to
perform Write and Read operations. Due to the requirement for A0 pin to be driven to VHV, the SPA and the RPA
commands are fully supported in a single DIMM (isolated DIMM) end application or a single DIMM programming
station only.
Example:
If SPA = 0, then the first-half or lower 256 bytes of the Serial EEPROM is selected allowing
access to Quadrant 0 and Quadrant 1. Alternately, if SPA = 1, then the second-half or upper 256
bytes of the Serial EEPROM is selected allowing access to Quadrant 2 and Quadrant 3.
Table 6-1.
SPA Setting and Memory Organization
Block
Set Page Address (SPA)
Quadrant 0
Memory Address Locations
00h to 7Fh
0
Quadrant 1
Quadrant 2
80h to FFh
00h to 7Fh
1
Quadrant 3
80h to FFh
Setting the Set Page Address (SPA) value selects the desired half of the EEPROM for performing Write or Read
operations. This is done by sending the SPA as seen in Figure 6-1. The SPA command sequence requires the
Master to transmit a Start condition followed by sending a control byte of ‘011011*0’ where the ‘*’ in the
bit 7 position will dictate which half of the EEPROM is being addressed. A ‘0’ in this position (or 6Ch) is
required to set the page address to the first half of the memory and a ‘1’ (or 6Eh) is necessary to set the page
address to the second half of the memory. After receiving the control byte, the AT34C04 should return an ACK
and the Master should follow by sending two data bytes of don’t care values. The AT34C04 responds with a
ACK to each of these two data bytes although the JEDEC EE1004v specification allows for either an ACK or
NACK response. The protocol is completed by the Master sending a Stop condition to end the operation.
Figure 6-1.
Set Page Address (SPA)
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
X
0
SCL
Control Byte
SDA
0
1
1
0
1
Most Significant Data Byte
1
*
0
0
MSB
Start
by
Master
X
X
X
X
X
X
X
Least Significant Data Byte
X
0
MSB
ACK
from
Slave
X
X
X
X
X
X
X
MSB
ACK
from
Slave
ACK
from
Slave
Stop
by
Master
Bit * = 0: Indicates the page address is located in the first half of the memory.
Bit * = 1: Indicates the page address is located in the second half of the memory.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
13
Reading the state of the SPA can be accomplished via the Read Page Address (RPA) command. The Master
can issue the RPA command to determine if the AT34C04’s internal address counter is located in the first 2-Kbit
section or the second 2-Kbit memory section based upon the device’s ACK or NACK response to the RPA
command.
The RPA command sequence requires the Master to transmit a Start bit followed by a control byte of
‘01101101’ (6Dh). If the device’s current address counter (page address) is located in the first half of the
memory, the AT34C04 responds with an ACK to the RPA command. Alternatively, a NACK response to the
RPA command indicates the page address is located in the second half of the memory (see Figure 6-2).
Following the control byte and the device’s ACK or NACK response, the AT34C04 should transmit two data
bytes of don’t care values. The Master should NACK on these two data bytes followed by the Master sending a
Stop condition to end the operation.
After power-up, the SPA is set to zero indicating internal address counter is located in the first half of the
memory. Performing a software reset (see 2-wire Software Reset on page 8) will also set the SPA to zero.
The AT34C04 incorporates a Reversible Software Write Protect (RSWP) feature that allows the ability to
selectively write protect data stored in any or all of the four 128-byte quadrants. See Section 7. “Write
Protection” on page 20 for more information on the RSWP feature.
Figure 6-2.
Read Page Address (RPA)
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
X
1
SCL
Control Byte
SDA
0
1
1
0
1
Most Significant Data Byte
1
MSB
Start
by
Master
0
1
*
X
X
X
X
X
X
X
Least Significant Data Byte
X
1
MSB
ACK or NACK
from
Slave
X
X
X
X
X
X
X
MSB
NACK
from
Master
Bit * = 0: ACK indicates the device’s internal address counter is located in the first half of the memory.
Bit * = 1: NACK indicates the device’s internal address counter is located in the second half of the memory.
14
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
NACK
from
Master
Stop
by
Master
6.2
Read Operations
All Read operations are initiated by the Master transmitting a Start bit, a device type identifier of ‘1010’ (Ah),
three software address bits (A2, A1, A0) that match their corresponding hard-wired address pins (A2, A1, A0),
and the R/W select bit with a Logic 1 state. In the following clock cycle, the device should respond with an ACK.
The subsequent protocol depends on the type of Read operation desired. There are three Read operations:
Current Address Read, Random Address Read, and Sequential Read.
CAUTION:
6.2.1
All Read operations should be preceded by the SPA and/or RPA commands to ensure the
desired half of the memory is selected. The reason this is important, for example, during a
Sequential Read operation on the last byte in the first half of the memory (address FFh) with
SPA=0 (indicating first half is selected), the internal address counter will roll-over to address 00h
in the first half of memory as opposed to the first byte in the second half of the memory. For more
information on the SPA and RPA commands, see Section 6.1.1 on page 13.
Current Address Read
Following a Start condition, the Master only transmits the device address byte with the R/W select bit set to a
Logic 1 (see Figure 6-3). The AT34C04 should respond with an ACK and then serially transmits the data word
addressed by the internal address counter. The internal data word address counter maintains the last address
accessed during the last Read or Write operation, incremented by one. This address stays valid between
operations as long as power to the device is maintained. The address roll-over during a Read is from the last
byte of the last page to the first byte of the first page of the addressed 2-Kbit (depends on the current SPA
setting). To end the command, the Master does not respond with an ACK but does generate a following Stop
condition.
Figure 6-3.
Current Address Read
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
D2
D1
D0
1
SCL
Device Address Byte
SDA
1
0
1
0
A2
A1
Data Word (n)
A0
1
0
MSB
Start
by
Master
6.2.2
D7
D6
D5
D4
D3
MSB
ACK
from
Slave
NACK
from
Master
Stop
by
Master
Random Read
A Random Read operation allows the Master to access any memory location in a random manner and requires
a dummy write sequence to preload the starting data word address. To perform a Random Read, the device
address byte and the word address byte are transmitted to the AT34C04 as part of the dummy write sequence
(see Figure 6-4). Once the device address byte and data word address are clocked in and acknowledged by the
AT34C04, the Master must generate another Start condition. The Master initiates a Current Address Read by
sending another device address byte with the R/W select bit to a Logic 1. The AT34C04 acknowledges the
device address byte, increments its internal address counter and serially clocks out the first data word. The
device will continue to transmit sequential data words as long as the Master continues to ACK each data word.
To end the sequence, the Master responds with a NACK and a Stop condition.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
15
Figure 6-4.
Random Read
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
A1
A0
0
SCL
Device Address Byte
SDA
1
0
1
0
A2
A1
Word Address Byte
A0
0
0
A7
MSB
A6
A5
A4
A3
A2
MSB
Start
by
Master
ACK
from
Slave
ACK
from
Slave
Dummy Write
1
2
3
4
5
6
7
8
9
1
2
3
0
1
0
A2
A1
A0
1
0
D7
MSB
6
7
8
9
D6
D5
D4
D3
D2
D1
D0
1
MSB
Start
by
Master
6.2.3
5
Data Word (n)
Device Address Byte
1
4
NACK
from
Master
ACK
from
Slave
Stop
by
Master
Sequential Read
A Sequential Read operation is initiated in the same way as a Random Read operation, except after the
AT34C04 transmits the first data word, the Master responds with an ACK (instead of a NACK followed by a Stop
condition). As long as the AT34C04 receives an ACK, it will continue to increment the data word address and
serially clock out the sequential data words (see Figure 6-5). When the internal address counter is at the last
byte of the last page, the data word address will roll-over to the beginning of the selected 2-Kbit array
(depending on the SPA setting) starting at address zero, and the Sequential Read operation will continue. The
Sequential Read operation is terminated when the Master responds with a NACK followed by a Stop condition.
Figure 6-5.
Sequential Read
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
D2
D1
D0
0
SCL
Device Address Byte
SDA
1
0
1
0
A2
A1
Data Word (n)
A0
1
0
D7
MSB
Start
by
Master
1
2
3
4
5
6
7
8
9
D4
D3
ACK
from
Master
1
2
D6
D5
D4
D3
D2
3
4
5
6
7
8
9
1
2
D1
D0
0
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
D6
D5
D4
D3
D2
D1
D0
0
MSB
ACK
from
Master
AT34C04 [DATASHEET]
D7
3
4
5
6
7
8
9
D1
D0
1
Data Word (n+x)
Data Word (n+2)
MSB
16
D5
ACK
from
Slave
Data Word (n+1)
D7
D6
MSB
D7
D6
D5
D4
D3
D2
MSB
ACK
from
Master
NACK
from
Master
Stop
by
Master
6.3
Write Operations
The AT34C04 supports single Byte Write and Page Write operations up to the maximum page size of 16 bytes
in one operation. The only difference between a Byte Write and a Page Write operation is the amount of data
bytes sent to the device. Regardless of whether a Byte Write or Page Write operation is performed, the
internally self-timed write cycle will take the same amount of time to write the data to the addressed memory
location(s).
CAUTION:
All Byte Write and Page Write operations should be preceded by the SPA and or RPA commands
to ensure the internal address counter is located in the desired half of the memory.
If a Byte Write or Page Write operation is attempted to a protected quadrant, the AT34C04 will respond (ACK or
NACK) to the write operation according to Table 6-2.
Table 6-2.
Acknowledge Status When Writing Data or Defining Write Protection
Instruction
ACK
Word
Address
ACK
Data
Word
ACK
Write
Cycle
Set RSWP
NACK
Don’t Care
NACK
Don’t Care
NACK
No
Clear RSWP
ACK
Don’t Care
ACK
Don’t Care
ACK
Yes
Byte Write or Page
Write to Protected
Quadrant
ACK
Word
Address
ACK
Data
NACK
No
ACK
Don’t Care
ACK
Don’t Care
ACK
Yes
ACK
Word
Address
ACK
Data
ACK
Yes
Quadrant Status
Write Protected
with Set RSWP
Set RSWP or
Clear RSWP
Not Protected
6.3.1
Byte Write or Page
Write
Byte Write
Following the Start condition from the Master, the device type identifier (‘1010’), the device address bits and
the R/W select bit (set to a Logic 0) are clocked onto the bus by the Master. This indicates to the addressed
device that the Master will follow by transmitting a byte with the word address. The AT34C04 will respond with
an ACK during the ninth clock cycle. Then the next byte transmitted by the Master is the 8-bit word address of
the byte location to be written into the Serial EEPROM. After receiving an ACK from the AT34C04, the Master
transmits the data word to be programmed followed by an ACK from the AT34C04. The Master ends the Write
sequence with a Stop condition during the 10th clock cycle to initiate the internally self-timed write cycle. A Stop
condition issued during any other clock cycle during the Write operation will not trigger the internally self-timed
write cycle. Once the write cycle begins, the pre-loaded data word will be programmed in the amount of time not
to exceed the tWR specification. The tWR time is defined in more detail in Section 6.3.4 on page 19. During this
time, the Master should wait a fixed amount of time set to the tWR specification, or for time sensitive applications,
an ACK polling routine can be implemented. All inputs are ignored by the device during the write cycle and the
device will not respond until the write cycle is complete (see Figure 6-9). The Serial EEPROM will increment its
internal address counter each time a byte is written.
Figure 6-6.
Byte Write
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
D2
D1
D0
0
SCL
Device Address Byte
SDA
1
0
1
0
A2
A1
Word Address Byte
A0
0
0
MSB
Start
by
Master
A7
A6
A5
A4
A3
A2
Data Word
A1
A0
0
MSB
ACK
from
Slave
D7
D6
D5
D4
D3
MSB
ACK
from
Slave
ACK
from
Slave
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
Stop
by
Master
17
6.3.2
Page Write
The 4-Kbit Serial EEPROM is capable of writing up to 16 data bytes at a time executing the Page Write protocol
sequence. A partial or full Page Write operation is initiated the same as a Byte Write operation except that the
Master does not send a Stop condition after the first data word is clocked in. Instead, after the device has
acknowledged receipt of the first data word, the Master can transmit up to fifteen more data words. The device
will respond with an ACK after each data word is received. The Master must terminate the Page Write sequence
with a Stop condition during the 10th clock cycle (see Figure 6-7) to start the write cycle. A Stop condition issued
at any other clock cycle will not initiate the internally self-timed write cycle and the Write sequence will have to
be repeated again.
Once the write cycle begins, the data words should be programmed in the amount of time not exceed the tWR
parameter (see Figure 6-9). During this time, the Master should wait a fixed amount of time set to the specified
tWR parameter, or for time sensitive applications, an Acknowledge polling routine can be implemented as
described in Section 6.3.3. The tWR time is defined in more detail in Section 6.3.4 on page 19. The lower four
bits of the data word address are internally incremented following the receipt of each data word. The higher data
word address bits are not incremented, retaining the memory page row location. When the internally generated
word address reaches the page boundary, then the following data word is placed at the beginning of the same
page. If more than sixteen data words are transmitted to the device, the data word address will roll-over and the
previous data will be overwritten. The address roll-over during a Write sequence is from the last byte of the
current page to the first byte of the same page.
Figure 6-7.
Page Write
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
A1
A0
0
SCL
Device Address Byte
SDA
1
0
1
0
A2
A1
Word Address Byte
A0
0
0
A7
MSB
Start
by
Master
1
2
3
4
5
6
7
8
9
A4
A3
A2
ACK
from
Slave
1
2
D6
D5
D4
D3
D2
3
4
5
6
7
8
9
1
2
D1
D0
0
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
D6
D5
D4
D3
D2
D1
D0
0
MSB
ACK
from
Slave
AT34C04 [DATASHEET]
D7
3
4
5
6
7
8
9
D1
D0
0
Data Word (n+15)
Data Word (n+1)
MSB
18
A5
ACK
from
Slave
Data Word (n)
D7
A6
MSB
D7
D6
D5
D4
D3
D2
MSB
ACK
from
Slave
ACK
from
Slave
Stop
by
Master
6.3.3
Acknowledge (ACK) Polling
An ACK polling routine can be implemented to optimize time sensitive applications that would not prefer waiting
the fixed maximum write cycle time and would prefer to know immediately when the Serial EEPROM write cycle
has completed to start a subsequent operation. Once the internally self timed write cycle has started (the Stop
condition during the 10th clock cycle at the end of the Write sequence), the device inputs are disabled and ACK
polling can be initiated (see
Figure 6-8). An ACK polling routine involves sending a valid Start condition followed by the device address byte.
While the write cycle is in progress, the device will not respond with an ACK indicating the device is busy writing
data. Once complete, the device will ACK and the next device operation can be started.
Figure 6-8.
Acknowledge Polling Flow Chart
Send
Stop
Condition
to Initiate
Write Cycle
Send Any
Write
Protocol
Send Start
Condition
Followed
by Valid
Device Address
Byte
Did
the Device
ACK?
YES
Continue to
Next Operation
NO
6.3.4
Write Cycle Timing
The length of the self timed write cycle, or tWR, is defined as the amount of time from a valid Stop condition that
begins the internal write sequence to the Start condition of the first device address byte sent to the AT34C04
that it subsequently responds to with an ACK. Figure 6-9 has been included to show this measurement.
Figure 6-9.
Write Cycle Timing
SCL: Serial Clock, SDA: Serial Data I/O
SCL
8
9
9
ACK
ACK
Data Word n
SDA
D0
tWR
Stop
Condition
Start
Condition
First Acknowledge from the device
to a valid device address sequence after
write cycle is initiated. The minumum tWR
can only be determined through
the use of an ACK Polling routine.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
Stop
Condition
19
7.
Write Protection
The AT34C04 incorporates a Reversible Software Write Protection (RSWP) feature that allows the ability to
selectively write protect data stored in each of the four independent 128-byte EEPROM quadrants. Table 7-1
identifies the memory quadrant identifier with its associated quadrant, SPA and memory address locations.
The AT34C04 has three RSWP software commands:



Set RSWP command for setting the RSWP.
Clear RSWP command for resetting all of the quadrants to an unprotected state.
Read RSWP command for checking the RSWP status.
Table 7-1.
7.1
Memory Organization
Block
SPA
Address Locations
Memory Quadrant Identifier
Quadrant 0
0
00h to 7Fh
001
Quadrant 1
0
80h to FFh
100
Quadrant 2
1
00h to 7Fh
101
Quadrant 3
1
80h to FFh
000
Set RSWP
Setting the RSWP is enabled by sending the Set RSWP command, similar to a normal Write command to the
device which programs the write protection to the target quadrant. The Set RSWP sequence requires sending a
control byte of ‘0110MMM0’ (where ‘M’ represents the memory quadrant identifier for the target quadrant to be
write-protected) with the R/W bit set to a Logic 0. In conjunction with sending the protocol, the A0 pin must be
connected to VHV for the duration of the RSWP sequence (see Figure 7-1). The Set RSWP command acts on a
single quadrant only as specified in the Set RSWP command and can only be reversed by issuing the Clear
RSWP command and will unprotect all quadrants in one operation (see Table 7-2).
Example:
If Quadrant 0 and Quadrant 3 are to be write-protected, two separate Set RSWP commands
would be required; however, only one Clear RSWP command is needed to clear and unprotect
both quadrants.
Table 7-2.
Set RSWP and Clear RSWP
Control Byte
Pin
Function
A2
A1
Set RSWP, Quadrant 0
X
Set RSWP, Quadrant 1
Bit 2
Bit 1
Bit 0
X
0
0
1
0
X
X
1
0
0
0
Set RSWP, Quadrant 2
X
X
1
0
1
0
Set RSWP, Quadrant 3
X
X
0
0
0
0
Clear RSWP
X
X
0
1
1
0
1.
2.
3.
A0
VHV
Bit 7
0
Bit 6
1
Bit 5
1
Bit 4
R/W
Bit 3
Notes:
20
Memory Quadrant
Identifier
Device Type Identifier
0
X = Don’t care but recommended to be hard-wired to VCC or GND.
See Table 5-1 for VHV value.
Due to the requirement for the A0 pin to be driven to VHV, the RSWP set and RSWP clear commands are fully
supported in a single DIMM (isolated DIMM) end application or a single DIMM programming station only.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
Figure 7-1.
Set RSWP and Clear RSWP
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
X
X
X
0/1
SCL
Control Byte
SDA
0
1
1
0
M
Word Address Byte
M
M
0
0
MSB
X
X
X
X
X
X
Data Word
X
X
0/1
MSB
Start
by
Master
X
X
X
X
X
MSB
ACK
from
Slave
Stop
by
ACK or NACK
Master
from
Slave
ACK or NACK
from
Slave
M = Memory Quadrant Identifier
X = Don’t care
7.2
Clear RSWP
Similar to the Set RSWP command, the reversible write protection on all quadrants can be reversed or
unprotected by transmitting the Clear RSWP command. The Clear RSWP sequence requires the Master to
send a Start condition followed by sending a control byte of ‘01100110’(66h) with the R/W bit set to a Logic 0.
The AT34C04 should respond with an ACK. The Master transmits a word address byte and data bytes with
don’t care values. The AT34C04 will respond with either an ACK or NACK to both the word address and data
word. In conjunction with sending the protocol, the A0 pin must be connected to VHV for the duration of the Clear
RSWP command (see Figure 7-1). To end the Clear RSWP sequence, the Master sends a Stop condition.
CAUTION:
7.3
The write protection of individual quadrants cannot be reversed separately, and executing the
Clear RSWP command will clear the write protection on all four quadrants leaving all quadrants
with no software write protection.
Read RSWP
The Read RSWP command allows the ability to check a quadrant’s write protection status. To find out if the
software write protection has been set to a specific quadrant, the same procedure that was used to set the
quadrant’s write protection can be utilized except that the R/W select bit is set to a Logic 1, and the A0 pin is not
required to have VHV (see Table 7-4).
The Read RSWP sequence requires sending a control byte of ‘0110MMM1’ (where the ‘M’ represents the
memory quadrant identifier for the quadrant to be read) with the R/W bit set to a Logic 1 (see Figure 7-2).
If the RSWP has not been set, then the AT34C04 responds to the control byte with an ACK. If the RSWP has
been set, the AT34C04 responds with a NACK. In either case, both Word Address and Data Word bytes will not
be acknowledged. The operation is completed by the Master creating a Stop Condition. A summary of the
response is shown in Table 7-3.
Table 7-3.
Acknowledge When Reading Protection Status
Word
Address
Sent
Word
Address
Response
Data Word
Sent
Data
Word
Response
Quadrant Status
Instruction Sent
Instruction
Response
Write Protected
Read RSWP
NACK
Don’t Care
NACK
Don’t Care
NACK
Not Protected
Read RSWP
ACK
Don’t Care
NACK
Don’t Care
NACK
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
21
Table 7-4.
Read RSWP
Control Byte
Pin
Function
A2
A1
Read RSWP, Quadrant 0
X
X
Read RSWP, Quadrant 1
X
X
Read RSWP, Quadrant 2
X
X
Read RSWP, Quadrant 3
X
X
Note:
1.
Memory Quadrant
Identifier
Device Type Identifier
A0
B7
0, 1
or
VHV
B6
0
B5
1
B4
1
0
R/W
B3
B2
B1
B0
0
0
1
1
1
0
0
1
1
0
1
1
0
0
0
1
X = Don’t care but recommend to be hard-wired to VCC or GND.
Figure 7-2.
Read RSWP
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
X
X
X
1
SCK
Control Byte
SDA
0
1
1
0
M
Word Address Byte
M
M
MSB
Start
by
Master
M = Memory Quadrant Identifier
X = Don’t care
22
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
1
0/1
X
X
X
X
X
X
Data Byte
X
X
1
MSB
ACK or NACK
from
Slave
X
X
X
X
X
MSB
NACK
from
Master
NACK
from
Master
Stop
by
Master
8.
Part Marking Detail
8.1
Part Markings
AT34C04: Package Marking Information
8-lead TSSOP
8-lead SOIC
8-lead UDFN
2.0 x 3.0 mm Body
Note 1:
44
5M@
YXX
AT5YWW
44 M @
AAAAAAA
ATML5YWW
44 M
@
AAAAAAAA
designates pin 1
Note 2: Package drawings are not to scale
Catalog Number Truncation
AT34C04
Truncation Code ##: 44
Date Codes
Y = Year
2: 2012
3: 2013
4: 2014
5: 2015
Voltages
6: 2016
7: 2017
8: 2018
9: 2019
M = Month
A: January
B: February
...
L: December
WW = Work Week of Assembly
02: Week 2
04: Week 4
...
52: Week 52
Country of Assembly
Lot Number
@ = Country of Assembly
AAA...A = Atmel Wafer Lot Number
Trace Code
M: 1.7V min
Grade/Lead Finish Material
5: Industrial (C)
(-20°C to 125°C)/NiPdAu
Atmel Truncation
XX = Trace Code (Atmel Lot Numbers Correspond to Code)
Example: AA, AB.... YZ, ZZ
AT: Atmel
ATM: Atmel
ATML: Atmel
8/16/12
TITLE
Package Drawing Contact:
[email protected]
34C04SM, AT34C04 Package Marking Information
DRAWING NO.
REV.
34C04SM
B
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
23
9.
Ordering Code Detail
AT 3 4 C 0 4 - M A 5 M - T
Atmel Designator
Shipping Carrier Option
B
T
E
Product Family
=
=
=
Bulk (Tubes)
Tape and Reel, Standard Quantity Option
Tape and Reel, Expanded Quantity Option
Voltage Option
34C = I2C-compatible
Serial Presence Detect (SPD)
Serial EEPROM
M
=
1.7V to 3.6V
Device Grade
5
Device Density
=
04 = 4-Kbit
Green, NiPdAu Lead Finish
Temperature Range
(-20°C to +125°C)
Package Option
SS =
X =
MA =
10.
JEDEC SOIC
TSSOP
UDFN
Ordering Information
Additional package types that are not listed below may be available for order. Please contact Atmel for availability details.
Delivery Information
Atmel Ordering Code
Lead Finish
AT34C04-SS5M-B
8S1
AT34C04-SS5M-T
AT34C04-X5M-B
AT34C04-X5M-T
Package
NiPdAu
(Lead-free/Halogen-free)
AT34C04-MA5M-T
AT34C04-MA5M-E
8X
8MA2
Form
Quantity
Bulk (Tubes)
100 per Tube
Tape and Reel
4,000 per Reel
Bulk (Tubes)
100 per Tube
Tape and Reel
5,000 per Reel
Tape and Reel
5,000 per Reel
Tape and Reel
15,000 per Reel
Operational
Range
-20C to 125C
Package Type
24
8S1
8-lead, 0.150” wide body, Plastic Gull Wing Small Outline (JEDEC SOIC)
8X
8-lead, 4.4mm body, Plastic Thin Shrink Small Outline (TSSOP)
8MA2
8-pad, 2.0 x 3.0mm body, 0.5mm pitch, Thermally Enhanced Plastic Ultra Thin Dual Flat No Lead (UDFN)
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
11.
Package Information
11.1
8S1 — 8-lead JEDEC SOIC
C
1
E
E1
L
N
Ø
TOP VIEW
END VIEW
e
b
COMMON DIMENSIONS
(Unit of Measure = mm)
A
A1
D
SIDE VIEW
Notes: This drawing is for general information only.
Refer to JEDEC Drawing MS-012, Variation AA
for proper dimensions, tolerances, datums, etc.
MIN
NOM
MAX
–
–
1.75
A1
0.10
–
0.25
b
0.31
–
0.51
C
0.17
–
0.25
SYMBOL
A
D
4.90 BSC
E
6.00 BSC
E1
3.90 BSC
e
NOTE
1.27 BSC
L
0.40
–
1.27
Ø
0°
–
8°
3/6/2015
Package Drawing Contact:
[email protected]
TITLE
8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing
Small Outline (JEDEC SOIC)
GPC
SWB
DRAWING NO.
REV.
8S1
H
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
25
11.2
8X — 8-lead TSSOP
C
1
Pin 1 indicator
this corner
E1
E
L1
N
L
Top View
End View
A
b
A1
e
D
SYMBOL
Side View
Notes:
COMMON DIMENSIONS
(Unit of Measure = mm)
A2
1. This drawing is for general information only.
Refer to JEDEC Drawing MO-153, Variation AA, for proper
dimensions, tolerances, datums, etc.
2. Dimension D does not include mold Flash, protrusions or gate
burrs. Mold Flash, protrusions and gate burrs shall not exceed
0.15mm (0.006in) per side.
3. Dimension E1 does not include inter-lead Flash or protrusions.
Inter-lead Flash and protrusions shall not exceed 0.25mm
(0.010in) per side.
4. Dimension b does not include Dambar protrusion.
Allowable Dambar protrusion shall be 0.08mm total in excess
of the b dimension at maximum material condition. Dambar
cannot be located on the lower radius of the foot. Minimum
space between protrusion and adjacent lead is 0.07mm.
5. Dimension D and E1 to be determined at Datum Plane H.
MIN
NOM
MAX
A
-
-
1.20
A1
0.05
-
0.15
A2
0.80
1.00
1.05
D
2.90
3.00
3.10
2, 5
E
NOTE
6.40 BSC
E1
4.30
4.40
4.50
3, 5
b
0.19
0.25
0.30
4
e
L
0.65 BSC
0.45
L1
C
0.60
0.75
1.00 REF
0.09
-
0.20
2/27/14
TITLE
Package Drawing Contact:
[email protected]
26
8X, 8-lead 4.4mm Body, Plastic Thin
Shrink Small Outline Package (TSSOP)
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
GPC
TNR
DRAWING NO.
8X
REV.
E
11.3
8MA2 — 8-pad UDFN
E
1
8
Pin 1 ID
2
7
3
6
4
5
D
C
TOP VIEW
A2
SIDE VIEW
A
A1
E2
b (8x)
8
7
1
D2
6
3
5
4
e (6x)
K
L (8x)
BOTTOM VIEW
Notes:
COMMON DIMENSIONS
(Unit of Measure = mm)
2
Pin#1 ID
1. This drawing is for general information only. Refer to
Drawing MO-229, for proper dimensions, tolerances,
datums, etc.
2. The Pin #1 ID is a laser-marked feature on Top View.
3. Dimensions b applies to metallized terminal and is
measured between 0.15 mm and 0.30 mm from the
terminal tip. If the terminal has the optional radius on
the other end of the terminal, the dimension should
not be measured in that radius area.
4. The Pin #1 ID on the Bottom View is an orientation
feature on the thermal pad.
SYMBOL
MIN
NOM
MAX
A
0.50
0.55
0.60
A1
0.0
0.02
0.05
A2
-
-
0.55
D
1.90
2.00
2.10
D2
1.40
1.50
1.60
E
2.90
3.00
3.10
E2
1.20
1.30
1.40
b
0.18
0.25
0.30
C
L
3
1.52 REF
0.30
e
K
NOTE
0.35
0.40
0.50 BSC
0.20
-
-
11/26/14
Package Drawing Contact:
[email protected]
TITLE
8MA2, 8-pad 2 x 3 x 0.6mm Body, Thermally
Enhanced Plastic Ultra Thin Dual Flat No-Lead
Package (UDFN)
GPC
DRAWING NO.
REV.
YNZ
8MA2
G
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
27
12.
Revision History
Doc. Rev.
Date
8827F
10/2015
8827E
01/2015
8827D
12/2013
Comments
Correct Set Page Address figure and section.
Add the UDFN extended quantity product offering.
Update 8X and 8MA2 package outline drawings and the ordering information section.
Remove Preliminary datasheet status.
Remove part number, AT34C04-MA5M-B.
8827C
07/2013
Update electrical specifications.
Update footers and disclaimer page.
Increase VPOR maximum from 1.5V to 1.6V.
8827B
12/2012
Decrease tI 100kHz maximum from 100ns to 50ns.
Minor changes to DC and AC characteristic tables.
Update datasheet status from advance to preliminary.
8827A
28
09/2012
Initial document release.
AT34C04 [DATASHEET]
Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015
XXXXXX
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2015 Atmel Corporation. / Rev.: Atmel-8827F-SEEPROM-AT34C04-Datasheet_102015.
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and
other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.