AT27LV010A - Complete

Features
• Fast read access time – 70ns
• Dual voltage range operation
•
•
•
•
•
•
•
•
•
– Low voltage power supply range, 3.0V to 3.6V, or
– Standard power supply range, 5V  10%
Compatible with JEDEC standard Atmel® AT27C010
Low-power CMOS operation
– 20µA max standby (less than 1µA, typical) for VCC = 3.6V
– 29mW max active at 5MHz for VCC = 3.6V
JEDEC standard package
– 32-lead PLCC
High-reliability CMOS technology
– 2,000V ESD protection
– 200mA latchup immunity
Rapid programming algorithm –100µs/byte (typical)
CMOS- and TTL-compatible inputs and outputs
– JEDEC standard for LVTTL
Integrated product identification code
Industrial temperature range
Green (Pb/halide-free) packaging option
1.
1Mb (128K x 8)
Low Voltage,
One-time
Programmable,
Read-only Memory
Atmel AT27LV010A
Description
The Atmel AT27LV010A is a high-performance, low-power, low-voltage 1,048,576-bit,
one-time programmable, read-only memory (OTP EPROM) organized as 128K by 8 bits. It
requires only one supply in the range of 3.0V to 3.6V in normal read mode operation, making it ideal for fast, portable systems using battery power.
The Atmel innovative design techniques provide fast speeds that rival 5V parts, while keeping the low power consumption of a 3.3V supply. At VCC = 3.0V, any byte can be accessed
in less than 70ns. With a typical power dissipation of only 18mW at 5MHz and VCC = 3.3V,
the AT27LV010A consumes less than one-fifth the power of a standard, 5V EPROM.
Standby mode supply current is typically less than 1µA at 3.3V.
The AT27LV010A is available in an industry-standard, JEDEC-approved, one-time programmable (OTP) PLCC package. All devices feature two-line control (CE, OE) to give
designers the flexibility to prevent bus contention.
The AT27LV010A operating with VCC at 3.0V produces TTL-level outputs that are compatible with standard TTL logic devices operating at VCC = 5.0V. The device is also capable of
standard, 5V operation, making it ideally suited for dual supply range systems or card products that are pluggable in both 3V and 5V hosts.
The AT27LV010A has additional features to ensure high quality and efficient production use.
The rapid programming algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 100µs/byte. The
integrated product identification code electronically identifies the device and manufacturer.
This feature is used by industry-standard programming equipment to select the proper programming algorithms and voltages. The AT27LV010A programs in exactly the same way as
a standard, 5V Atmel AT27C010, and uses the same programming equipment.
0548F–EPROM–4/11
Pin configurations
Addresses
O0 - O7
Outputs
CE
Chip enable
OE
Output enable
PGM
Program strobe
NC
No connect
A12
A15
A16
VPP
VCC
PGM
NC
A0 - A16
32-lead PLCC
Top view
A7
A6
A5
A4
A3
A2
A1
A0
O0
4
3
2
1
32
31
30
Function
5
6
7
8
9
10
11
12
13
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
Pin name
A14
A13
A8
A9
A11
OE
A10
CE
O7
O1
O2
GND
O3
O4
O5
O6
2.
3.
System considerations
Switching between active and standby conditions via the chip enable pin may produce transient voltage excursions. Unless
accommodated by the system design, these transients may exceed datasheet limits, resulting in device nonconformance.
At a minimum, a 0.1µF, high-frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This
capacitor should be connected between the VCC and ground terminals of the device, as close to the device as possible.
Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7µF bulk electrolytic
capacitor should be utilized, again connected between the VCC and ground terminals. This capacitor should be positioned as
close as possible to the point where the power supply is connected to the array.
Figure 3-1.
2
Block diagram
Atmel AT27LV010A
0548F–EPROM–4/11
Atmel AT27LV010A
4.
Absolute maximum ratings*
*NOTICE:
Temperature under bias . . . . . . . . . . . . . . . -40°C to +85°C
Stresses beyond those listed under “Absolute
maximum ratings” may cause permanent damage to
the device. This is a stress rating only, and functional
operation of the device at these or any other conditions
beyond those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect device reliability.
Storage temperature . . . . . . . . . . . . . . . . .-65°C to +125°C
Voltage on any pin with
respect to ground . . . . . . . . . . . . . . . . . . . -2.0V to +7.0V(1)
Voltage on A9 with
respect to ground . . . . . . . . . . . . . . . . . -2.0V to +14.0V(1)
VPP supply voltage with
respect to ground . . . . . . . . . . . . . . . . . . -2.0V to +14.0V(1)
Note:
5.
1. Minimum voltage is -0.6V DC, which may undershoot to -2.0V for pulses of less than 20ns. Maximum output pin voltage is
VCC + 0.75V DC, which may be exceeded if certain precautions are observed (consult application notes), and which may
overshoot to +7.0V for pulses of less than 20ns.
DC and AC characteristics
Table 5-1.
Operating modes
Mode/Pin
CE
OE
Read(2)
VIL
VIL
Ai
VPP
VCC
Outputs
X(1)
Ai
X
VCC
DOUT
X
VIH
X
X
X
VCC
High Z
VIH
X
X
X
X
VCC
High Z
Rapid program
VIL
VIH
VIL
Ai
VPP
VCC
DIN
PGM verify(3)
VIL
VIL
VIH
Ai
VPP
VCC
DOUT
(3)
VIH
X
X
X
VPP
VCC
High Z
X
VCC
Identification code
(2)
Output disable
(2)
Standby
(3)
PGM inhibit
Product identification(3)(5)
Note:
PGM
VH(4)
VIL
VIL
X
A9 =
A0 = VIH or VIL
A1 - A16 = VIL
1. X can be VIL or VIH.
2. Read, output disable, and standby modes require 3.0V  VCC  3.6V or 4.5V  VCC  5.5V.
3. Refer to programming characteristics. Programming modes require VCC = 6.5V.
4. VH = 12.0 ± 0.5V.
5. Two identifier bytes may be selected. All Ai inputs are held low (VIL), except A9, which is set to VH, and A0, which is toggled low (VIL) to select the manufacturer’s identification byte and high (VIH) to select the device code byte.
Table 5-2.
DC and AC operating conditions for read operation
Atmel AT27LV010A-70
Industrial operating temperature (case)
-40°C - 85°C
3.0V to 3.6V
VCC power supply
5V  10%
3
0548F–EPROM–4/11
Table 5-3.
Symbol
DC and operating characteristics for read operation
Parameter
Condition
Min
Max
Units
VCC = 3.0V to 3.6V
ILI
ILO
IPP1
(2)
Input load current
VIN = 0V to VCC
1
µA
Output leakage current
VOUT = 0V to VCC
5
µA
VPP(1)
VPP = VCC
10
µA
ISB1 (CMOS), CE = VCC 0.3V
20
µA
ISB2 (TTL), CE = 2.0 to VCC + 0.5V
100
µA
8
mA
read/standby current
ISB
VCC(1) standby current
ICC
VCC active current
VIL
Input low voltage
-0.6
0.8
V
VIH
Input high voltage
2.0
VCC + 0.5
V
VOL
Output low voltage
IOL = 2.0mA
0.4
V
VOH
Output high voltage
IOH = -2.0mA
f = 5MHz, IOUT = 0mA, CE = VIL
2.4
V
VCC = 4.5V to 5.5V
ILI
ILO
IPP1
(2)
Input load current
VIN = 0V to VCC
1
µA
Output leakage current
VOUT = 0V to VCC
5
µA
VPP(1)
VPP = VCC
10
µA
ISB1 (CMOS), CE = VCC  0.3V
100
µA
ISB2 (TTL), CE = 2.0 to VCC + 0.5V
1
mA
f = 5MHz, IOUT = 0mA, CE = VIL
25
mA
read/standby current
ISB
VCC(1) standby current
ICC
VCC active current
VIL
Input low voltage
-0.6
0.8
V
VIH
Input high voltage
2.0
VCC + 0.5
V
VOL
Output low voltage
IOL = 2.1mA
0.4
V
VOH
Output high voltage
IOH = -400µA
Notes:
2.4
V
1. VCC must be applied simultaneously with or before VPP, and removed simultaneously with or after VPP.
2. VPP may be connected directly to VCC, except during programming. The supply current would then be the sum of ICC and
IPP.
Table 5-4.
AC characteristics for read operation
Atmel AT27LV010A-70
4
Symbol
Parameter
Condition
tACC(3)
Address to output delay
tCE(2)
tOE(2)(3)
tDF(4)(5)
OE or CE high to output float,
whichever occurred first
tOH
Output hold from address, CE or OE,
whichever occurred first
Min
Max
Units
CE = OE = VIL
70
ns
CE to output delay
OE = VIL
70
ns
OE to output delay
CE = VIL
40
ns
35
ns
0
ns
Atmel AT27LV010A
0548F–EPROM–4/11
Atmel AT27LV010A
Figure 5-1.
Notes:
AC waveforms for read operation(1)
1. Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified.
2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE.
3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC.
4. This parameter is only sampled, and is not 100% tested.
5. Output float is defined as the point when data is no longer driven.
Figure 5-2.
Input test waveforms and measurement level
tR, tF < 20 ns (10% to 90%)
Figure 5-3.
Output test load
Note: CL = 100pF including
jig capacitance.
5
0548F–EPROM–4/11
Table 5-5.
Pin capacitance
f = 1MHz, T = 25°C(1)
Symbol
Typ
Max
Units
Conditions
CIN
4
8
pF
VIN = 0V
COUT
8
12
pF
VOUT = 0V
Note:
1. Typical values for nominal supply voltage. This parameter is only sampled, and is not 100% tested.
Figure 5-4.
Notes:
Programming waveforms(1)
1. The input timing reference is 0.8V for VIL and 2.0V for VIH.
2. tOE and tDFP are characteristics of the device, but must be accommodated by the programmer.
3. When programming the Atmel AT27LV010A, a 0.1µF capacitor is required across VPP and ground to suppress spurious
voltage transients.
6
Atmel AT27LV010A
0548F–EPROM–4/11
Atmel AT27LV010A
Table 5-6.
DC programming characteristics
TA = 25  5°C, VCC = 6.5  0.25V, VPP = 13.0  0.25V
Limits
Symbol
Parameter
Test conditions
ILI
Input load current
VIN = VIL, VIH
VIL
Input low level
VIH
Input high level
VOL
Output low voltage
IOL = 2.1mA
VOH
Output high voltage
IOH = -400µA
ICC2
VCC supply current (program and verify)
IPP2
VPP supply current
VID
A9 product identification voltage
Table 5-7.
Min
Max
Units
10
µA
-0.6
0.8
V
2.0
VCC + 0.5
V
0.4
V
2.4
V
CE = PGM = VIL
11.5
40
mA
20
mA
12.5
V
Max
Units
AC programming characteristics
TA = 25  5°C, VCC = 6.5  0.25V, VPP = 13.0  0.2V
Limits
(1)
Symbol
Parameter
Test conditions
tAS
Address setup time
tCES
CE setup time
tOES
OE setup time
tDS
Data setup time
tAH
Address hold time
tDH
Data hold time
Input rise and fall times
(10% to 90%) 20ns
Input pulse levels
0.45V to 2.4V
tDFP
OE high to output float delay
tVPS
VPP setup time
tVCS
VCC setup time
(2)
Output timing reference level
0.8V to 2.0V
(3)
PGM program pulse width
tOE
Data valid from OE
tPRT
VPP pulse rise time during programming
2
µs
2
µs
2
µs
2
µs
0
µs
2
µs
0
Input timing reference level
0.8V to 2.0V
tPW
Notes:
Min
130
ns
2
µs
2
µs
95
105
µs
150
ns
50
ns
1. VCC must be applied simultaneously with or before VPP and removed simultaneously with or after VPP.
2. This parameter is only sampled, and is not 100% tested. Output float is defined as the point where data is no longer driven.
See timing diagram.
3. Program pulse width tolerance is 100µsec5%.
Table 5-8.
The Atmel AT27LV010A integrated product identification code(1)
Pins
A0
O7
O6
O5
O4
O3
O2
O1
O0
Hex data
Manufacturer
0
0
0
0
1
1
1
1
0
1E
Device type
1
0
0
0
0
0
1
0
1
05
Codes
Note:
1. The Atmel AT27LV010A has the same product identification code as the Atmel AT27C010. Both are programming
compatible.
7
0548F–EPROM–4/11
6.
Rapid programming algorithm
A 100µs PGM pulse width is used to program. The address is set to the first location. VCC is raised to 6.5V and VPP is raised
to 13.0V. Each address is first programmed with one 100µs PGM pulse without verification. Then a
verification/reprogramming loop is executed for each address. In the event a byte fails to pass verification, up to 10
successive 100µs pulses are applied with a verification after each pulse. If the byte fails to verify after 10 pulses have been
applied, the part is considered failed. After the byte verifies properly, the next address is selected until all have been
checked. VPP is then lowered to 5.0V and VCC to 5.0V. All bytes are read again and compared with the original data to
determine if the device passes or fails.
Figure 6-1.
8
Rapid programming algorithm
Atmel AT27LV010A
0548F–EPROM–4/11
Atmel AT27LV010A
7.
Ordering information
Green package option (Pb/halide-free)
ICC (mA)
VCC = 3.6V
tACC
(ns)
Active
Standby
Atmel ordering code
Package
Lead finish
Operation range
70
8
0.02
AT27LV010A-70JU
32J
Matte tin
Industrial
(-40°C to 85°C)
Package type
32J
32-lead, plastic, J-leaded chip carrier (PLCC)
9
0548F–EPROM–4/11
8.
Packaging Information
32J – PLCC
1.14(0.045) X 45°
PIN NO. 1
IDENTIFIER
1.14(0.045) X 45°
0.318(0.0125)
0.191(0.0075)
E1
E2
B1
E
B
e
A2
D1
A1
D
A
0.51(0.020)MAX
45° MAX (3X)
COMMON DIMENSIONS
(Unit of measure = mm)
D2
Notes:
1. This package conforms to JEDEC reference MS-016, variation AE.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.10mm) maximum.
SYMBOL
MIN
NOM
MAX
A
3.175
–
3.556
A1
1.524
–
2.413
A2
0.381
–
–
D
12.319
–
12.573
D1
11.354
–
11.506
D2
9.906
–
10.922
E
14.859
–
15.113
E1
13.894
–
14.046
E2
12.471
–
13.487
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
Package drawing contact:
[email protected]
10
TITLE
32J, 32-lead, plastic J-leaded chip carrier (PLCC)
DRAWING NO.
32J
REV.
B
Atmel AT27LV010A
0548F–EPROM–4/11
Atmel AT27LV010A
9.
Revision history
Doc. rev.
Date
0548F
04/2011
0548E
12/2007
Comments
Remove TSOP and VSOP packages
Add lead finish to ordering information
11
0548F–EPROM–4/11
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: (+1) (408) 441-0311
Fax: (+1) (408) 487-2600
www.atmel.com
Atmel Asia Limited
Unit 01-5 & 16, 19F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
HONG KONG
Tel: (+852) 2245-6100
Fax: (+852) 2722-1369
Atmel Munich GmbH
Business Campus
Parkring 4
D-85748 Garching b. Munich
GERMANY
Tel: (+49) 89-31970-0
Fax: (+49) 89-3194621
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
JAPAN
Tel: (+81) (3) 3523-3551
Fax: (+81) (3) 3523-7581
© 2011 Atmel Corporation. All rights reserved. / Rev.: 0548F–EPROM–4/11
Atmel®, logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel
products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY
RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE
THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to
make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not
be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.