ATMEL AT27C010-70TI

Features
• Fast Read Access Time – 45 ns
• Low-Power CMOS Operation
•
•
•
•
•
•
•
•
– 100 µA Max Standby
– 25 mA Max Active at 5 MHz
JEDEC Standard Packages
– 32-lead PDIP
– 32-lead PLCC
– 32-lead TSOP
5V ± 10% Supply
High Reliability CMOS Technology
– 2000V ESD Protection
– 200 mA Latchup Immunity
Rapid Programming Algorithm – 100 µs/Byte (Typical)
CMOS and TTL Compatible Inputs and Outputs
Integrated Product Identification Code
Industrial Temperature Range
Green (Pb/Halide-free) Packaging Option
1-Megabit
(128K x 8)
OTP EPROM
AT27C010
1. Description
The AT27C010 is a low-power, high-performance 1,048,576-bit one-time programmable read-only memory (OTP EPROM) organized as 128K by 8 bits. They require only
one 5V power supply in normal read mode operation. Any byte can be accessed in
less than 45 ns, eliminating the need for speed reducing WAIT states on high-performance microprocessor systems.
In read mode, the AT27C010 typically consumes only 8 mA. Standby mode supply
current is typically less than 10 µA.
The AT27C010 is available in a choice of industry-standard JEDEC-approved onetime programmable (OTP) plastic PDIP, PLCC, and TSOP packages. All devices feature two line control (CE, OE) to give designers the flexibility to prevent bus
contention.
With 128K byte storage capability, the AT27C010 allows firmware to be stored reliably
and to be accessed by the system without the delays of mass storage media.
Atmel’s AT27C010 has additional features to ensure high quality and efficient production use. The Rapid Programming Algorithm reduces the time required to program the
part and guarantees reliable programming. Programming time is typically only
100 µs/byte. The Integrated Product Identification Code electronically identifies the
device and manufacturer. This feature is used by industry-standard programming
equipment to select the proper programming algorithms and voltages.
0321M–EPROM–12/07
2. Pin Configurations
Pin Name
Function
A0 - A16
Addresses
O0 - O7
Outputs
CE
Chip Enable
OE
Output Enable
PGM
Program Strobe
NC
No Connect
2.3
32-lead PLCC Top View
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
5
6
7
8
9
10
11
12
13
O1
O2
GND
O3
O4
O5
O6
A7
A6
A5
A4
A3
A2
A1
A0
O0
4
3
2
1
32
31
30
A12
A15
A16
VPP
VCC
PGM
NC
2.1
2.2
A11
A9
A8
A13
A14
NC
PGM
VCC
VPP
A16
A15
A12
A7
A6
A5
A4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE
A10
CE
O7
O6
O5
O4
O3
GND
O2
O1
O0
A0
A1
A2
A3
32-lead PDIP Top View
VPP
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
O0
O1
O2
GND
2
A14
A13
A8
A9
A11
OE
A10
CE
O7
32-lead TSOP (Type 1) Top View
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
VCC
PGM
NC
A14
A13
A8
A9
A11
OE
A10
CE
O7
O6
O5
O4
O3
AT27C010
0321M–EPROM–12/07
AT27C010
3. System Considerations
Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may
exceed datasheet limits, resulting in device non-conformance. At a minimum, a 0.1 µF high
frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This
capacitor should be connected between the VCC and Ground terminals of the device, as close
to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit
boards with large EPROM arrays, a 4.7 µF bulk electrolytic capacitor should be utilized, again
connected between the VCC and Ground terminals. This capacitor should be positioned as
close as possible to the point where the power supply is connected to the array.
4. Block Diagram
5. Absolute Maximum Ratings*
Temperature Under Bias................................ -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin with
Respect to Ground .........................................-2.0V to +7.0V(1)
Voltage on A9 with
Respect to Ground ......................................-2.0V to +14.0V(1)
*NOTICE:
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at these or any other
conditions beyond those indicated in the operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
VPP Supply Voltage with
Respect to Ground .......................................-2.0V to +14.0V(1)
Note:
1. Minimum voltage is -0.6V DC which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is
VCC + 0.75V DC which may overshoot to +7.0 volts for pulses of less than 20 ns.
3
0321M–EPROM–12/07
6. Operating Modes
Mode/Pin
CE
OE
PGM
Ai
VPP
Outputs
Read
VIL
VIL
X(1)
Ai
X
DOUT
Output Disable
X
VIH
X
X
X
High Z
VIH
X
X
X
X
High Z
VIL
VIH
VIL
Ai
VPP
DIN
PGM Verify
VIL
VIL
VIH
Ai
VPP
DOUT
PGM Inhibit
VIH
X
X
X
VPP
High Z
X
Identification Code
Standby
Rapid Program
(2)
Product Identification(4)
Note:
VH(3)
VIL
VIL
A9 =
A0 = VIH or VIL
A1 - A16 = VIL
X
1. X can be VIL or VIH.
2. Refer to Programming Characteristics.
3. VH = 12.0 ± 0.5V.
4. Two identifier bytes may be selected. All Ai inputs are held low (VIL), except A9 which is set to VH and A0 which is toggled
low (VIL) to select the Manufacturer’s Identification byte and high (VIH) to select the Device Code byte.
7. DC and AC Operating Conditions for Read Operation
AT27C010
Operating Temp. (Case)
Ind.
-45
-70
-40° C - 85° C
-40° C - 85° C
5V ± 10%
5V ± 10%
VCC Power Supply
8. DC and Operating Characteristics for Read Operation
Max
Units
Ind.
±1
µA
Ind.
±5
µA
VPP = VCC
10
µA
ISB1 (CMOS), CE = VCC ± 0.3V
100
µA
ISB2 (TTL), CE = 2.0 to VCC + 0.5V
1
mA
f = 5 MHz, IOUT = 0 mA, CE = VIL
25
mA
-0.6
0.8
V
2.0
VCC + 0.5
V
0.4
V
Symbol
Parameter
Condition
ILI
Input Load Current
VIN = 0V to VCC
ILO
Output Leakage Current
VOUT = 0V to VCC
IPP1(2)
VPP(1)) Read/Standby Current
ISB
VCC(1) Standby Current
ICC
VCC Active Current
VIL
Input Low Voltage
VIH
Input High Voltage
VOL
Output Low Voltage
IOL = 2.1 mA
VOH
Output High Voltage
IOH = -400 µA
Note:
Min
2.4
V
1. VCC must be applied simultaneously or before VPP, and removed simultaneously or after VPP.
2. VPP may be connected directly to VCC, except during programming. The supply current would then be the sum of ICC and IPP.
4
AT27C010
0321M–EPROM–12/07
AT27C010
9. AC Characteristics for Read Operation
AT27C010
-45
Symbol
Parameter
Condition
tACC(3)
Min
-70
Max
Min
Max
Units
Address to Output Delay
CE = OE = VIL
45
70
ns
(2)
CE to Output Delay
OE = VIL
45
70
ns
tOE(2)(3)
OE to Output Delay
CE = VIL
20
30
ns
20
25
ns
tCE
tDF
(4)(5)
tOH
OE or CE High to Output Float, whichever occurred first
Output Hold from Address, CE or OE, whichever occurred first
7
7
ns
10. AC Waveforms for Read Operation(1)
Notes:
1. Timing measurement reference level is 1.5V for -45 devices. Input AC drive levels are VIL = 0.0V and VIH = 3.0V. Timing
measurement reference levels for all other speed grades are VOL = 0.8V and VOH = 2.0V. Input AC drive levels are VIL =
0.45V and VIH = 2.4V.
2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE.
3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC.
4. This parameter is only sampled and is not 100% tested.
5. Output float is defined as the point when data is no longer driven.
5
0321M–EPROM–12/07
11. Input Test Waveforms and Measurement Levels
For -45 devices only:
tR, tF < 5 ns (10% to 90%)
For -70 devices:
tR, tF < 20 ns (10% to 90%)
12. Output Test Load
Note:
CL = 100 pF including jig
capacitance, except for
the -45 devices, where
CL = 30 pF.
13. Pin Capacitance
f = 1 MHz, T = 25°C(1)
Symbol
Typ
Max
Units
Conditions
CIN
4
8
pF
VIN = 0V
COUT
8
12
pF
VOUT = 0V
Note:
6
1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested.
AT27C010
0321M–EPROM–12/07
AT27C010
14. Programming Waveforms(1)
Notes:
1. The Input Timing Reference is 0.8V for VIL and 2.0V for VIH.
2. tOE and tDFP are characteristics of the device but must be accommodated by the programmer.
3. When programming the AT27C010 at 0.1 µF capacitor is required across VPP and ground to suppress spurious voltage
transients.
7
0321M–EPROM–12/07
15. DC Programming Characteristics
TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V
Limits
Symbol
Parameter
Test Conditions
ILI
Input Load Current
VIN = VIL, VIH
VIL
Input Low Level
VIH
Input High Level
VOL
Output Low Voltage
IOL = 2.1 mA
VOH
Output High Voltage
IOH = -400 µA
ICC2
VCC Supply Current (Program and Verify)
IPP2
VPP Supply Current
VID
A9 Product Identification Voltage
Min
Max
Units
±10
µA
-0.6
0.8
V
2.0
VCC + 1
V
0.4
V
2.4
V
40
mA
20
mA
12.5
V
CE = PGM = VIL
11.5
16. AC Programming Characteristics
TA = 25 ± 5°C, VCC = 6.5 ± 0.25 V, VPP = 13.0 ± 0.25V
Limits
(1)
Symbol
Parameter
tAS
Address Setup Time
tCES
CE Setup Time
tOES
OE Setup Time
tDS
Data Setup Time
tAH
Address Hold Time
tDH
Data Hold Time
Test Conditions
Input Rise and Fall Times
(10% to 90%) 20 ns
Input Pulse Levels
0.45V to 2.4V
(2)
tDFP
OE High to Output Float Delay
tVPS
VPP Setup Time
tVCS
VCC Setup Time
tPW
PGM Program Pulse Width(3)
tOE
Data Valid from OE
tPRT
VPP Pulse Rise TIme During Programming
Note:
Min
Max
2
µs
2
µs
2
µs
2
µs
0
µs
2
µs
0
Input Timing Reference Level
0.8V to 2.0V
Output Timing Reference Level
0.8V to 2.0V
Units
130
ns
2
µs
2
µs
95
105
µs
150
ns
50
ns
1. VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP..
2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven –
see timing diagram.
3. Program Pulse width tolerance is 100 µsec ± 5%.
17. Atmel’s AT27C010 Integrated Product Identification Code
Pins
A0
O7
O6
O5
O4
O3
O2
O1
O0
Hex
Data
Manufacturer
0
0
0
0
1
1
1
1
0
1E
Device Type
1
0
0
0
0
0
1
0
1
05
Codes
8
AT27C010
0321M–EPROM–12/07
AT27C010
18. Rapid Programming Algorithm
A 100 µs PGM pulse width is used to program. The address is set to the first location. VCC is
raised to 6.5V and VPP is raised to 13.0V. Each address is first programmed with one 100 µs
PGM pulse without verification. Then a verification/reprogramming loop is executed for each
address. In the event a byte fails to pass verification, up to 10 successive 100 µs pulses are
applied with a verification after each pulse. If the byte fails to verify after 10 pulses have been
applied, the part is considered failed. After the byte verifies properly, the next address is
selected until all have been checked. VPP is then lowered to 5.0V and VCC to 5.0V. All bytes
are read again and compared with the original data to determine if the device passes or fails.
9
0321M–EPROM–12/07
19. Ordering Information
19.1
Standard Package
ICC (mA)
tACC
(ns)
Active
Standby
45
25
0.1
AT27C010-45JI
AT27C010-45PI
AT27C010-45TI
32J
32P6
32T
Industrial
(-40° C to 85° C)
70
25
0.1
AT27C010-70JI
AT27C010-70PI
AT27C010-70TI
32J
32P6
32T
Industrial
(-40° C to 85° C)
Note:
19.2
Ordering Code
Package
Operation Range
Not recommended for new designs. Use Green package option.
Green Package Option (Pb/Halide-free)
ICC (mA)
tACC
(ns)
Active
Standby
45
25
0.1
AT27C010-45JU
AT27C010-45PU
AT27C010-45TU
32J
32P6
32T
Industrial
(-40° C to 85° C)
70
25
0.1
AT27C010-70JU
AT27C010-70PU
AT27C010-70TU
32J
32P6
32T
Industrial
(-40° C to 85° C)
Ordering Code
Package
Operation Range
Package Type
32J
32-lead, Plastic J-leaded Chip Carrier (PLCC)
32P6
32-lead, 0.600" Wide, Plastic Dual Inline Package (PDIP)
32T
32-lead, Plastic Thin Small Outline Package (TSOP)
10
AT27C010
0321M–EPROM–12/07
AT27C010
20. Package Information
20.1
32J – PLCC
1.14(0.045) X 45˚
PIN NO. 1
IDENTIFIER
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
E1
E2
B1
E
B
e
A2
D1
A1
D
A
0.51(0.020)MAX
45˚ MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
D2
Notes:
1. This package conforms to JEDEC reference MS-016, Variation AE.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
SYMBOL
MIN
NOM
MAX
A
3.175
–
3.556
A1
1.524
–
2.413
A2
0.381
–
–
D
12.319
–
12.573
D1
11.354
–
11.506
D2
9.906
–
10.922
E
14.859
–
15.113
E1
13.894
–
14.046
E2
12.471
–
13.487
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC)
DRAWING NO.
REV.
32J
B
11
0321M–EPROM–12/07
20.2
32P6 – PDIP
D
PIN
1
E1
A
SEATING PLANE
A1
L
B
B1
e
E
0º ~ 15º
C
COMMON DIMENSIONS
(Unit of Measure = mm)
REF
MIN
NOM
MAX
A
–
–
4.826
A1
0.381
–
–
D
41.783
–
42.291
E
15.240
–
15.875
E1
13.462
–
13.970
B
0.356
–
0.559
B1
1.041
–
1.651
L
3.048
–
3.556
C
0.203
–
0.381
eB
15.494
–
17.526
SYMBOL
eB
Note:
1. Dimensions D and E1 do not include mold Flash or Protrusion.
Mold Flash or Protrusion shall not exceed 0.25 mm (0.010").
e
NOTE
Note 1
Note 1
2.540 TYP
09/28/01
R
12
2325 Orchard Parkway
San Jose, CA 95131
TITLE
32P6, 32-lead (0.600"/15.24 mm Wide) Plastic Dual
Inline Package (PDIP)
DRAWING NO.
32P6
REV.
B
AT27C010
0321M–EPROM–12/07
AT27C010
20.3
32T – TSOP
PIN 1
0º ~ 8º
c
Pin 1 Identifier
D1 D
L
b
e
L1
A2
E
A
GAGE PLANE
SEATING PLANE
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
19.80
20.00
20.20
D1
18.30
18.40
18.50
Note 2
E
7.90
8.00
8.10
Note 2
L
0.50
0.60
0.70
SYMBOL
Notes:
1. This package conforms to JEDEC reference MO-142, Variation BD.
2. Dimensions D1 and E do not include mold protrusion. Allowable
protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side.
3. Lead coplanarity is 0.10 mm maximum.
L1
0.25 BASIC
b
0.17
0.22
0.27
c
0.10
–
0.21
e
NOTE
0.50 BASIC
10/18/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
32T, 32-lead (8 x 20 mm Package) Plastic Thin Small Outline
Package, Type I (TSOP)
DRAWING NO.
REV.
32T
B
13
0321M–EPROM–12/07
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Atmel Europe
Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-enYvelines Cedex
France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Technical Support
[email protected]
Sales Contact
www.atmel.com/contacts
Product Contact
Web Site
www.atmel.com
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2007 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, and others are registered trademarks or trademarks of
Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
0321M–EPROM–12/07