ATtiny24/44/84 Automotive - Complete

ATtiny24/44/84
8-bit AVR Microcontroller with 2/4/8K Bytes In-System
Programmable Flash
DATASHEET
Features
● High performance, low power AVR® 8-bit microcontroller
● Advanced RISC architecture
● 120 powerful instructions – most single clock cycle execution
● 32 x 8 general purpose working registers
● Fully static operation
● Non-volatile program and data memories
● 2/4/8K byte of in-system programmable program memory flash (Atmel®
ATtiny24/44/84)
● Endurance: 10,000 write/erase cycles
● 128/256/512 bytes in-system programmable EEPROM (Atmel ATtiny24/44/84)
● Endurance: 100,000 write/erase cycles
● 128/256/512 bytes internal SRAM (Atmel ATtiny24/44/84)
● Programming lock for self-programming flash program and EEPROM data
security
● Peripheral features
● Two Timer/Counters, 8- and 16-bit counters with two PWM channels on both
● 10-bit ADC
● Eight single-ended channels
● 12 differential ADC channel pairs with programmable gain (1x, 20x)
● Temperature measurement
● Programmable watchdog timer with separate on-chip oscillator
● On-chip analog comparator
● Universal serial interface
● Special microcontroller features
●
●
●
●
●
●
●
●
●
debugWIRE on-chip debug system
In-system programmable via SPI port
External and internal interrupt sources
Pin change interrupt on 12 pins
Low power idle, ADC noise reduction, standby and power-down modes
Enhanced power-on reset circuit
Programmable brown-out detection circuit
Internal calibrated oscillator
On-chip temperature sensor
● I/O and packages
● 14-pin SOIC, 20-pin QFN/MLF: Twelve programmable I/O lines
7701G-AVR-02/15
● Operating voltage:
● 2.7 - 5.5V for Atmel ATtiny24/44/84
● Speed grade
● Atmel ATtiny24/44/84: 0 - 8MHz at 2.7 - 5.5V, 0 - 16MHz at 4.5 - 5.5V
● Automotive temperature range
● Low power consumption
● Active mode:
● 1MHz, 2.7V: 800µA
● Power-down mode:
● 2.7V: 2.0µA
2
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
1.
Pin Configurations
Figure 1-1. Pinout Atmel ATtiny24/44/84
SOIC
VCC
1
14
GND
(PCINT8/XTAL1) PB0
2
13
PA0 (ADC0/AREF/PCINT0)
(PCINT9/XTAL2) PB1
3
12
PA1 (ADC1/AIN0/PCINT1)
(PCINT11/RESET/dW) PB3
4
11
PA2 (ADC2/AIN1/PCINT2)
(PCINT10/INT0/OC0A/CKOUT) PB2
5
10
PA3 (ADC3/T0/PCINT3)
(PCINT7/ICP/OC0B/ADC7) PA7
6
9
PA4 (ADC4/USCK/SCL/T1/PCINT4)
(PCINT6/OC1A/SDA/MOSI/ADC6/) PA6
7
8
PA5 (ADC5/DO/MISO/OC1B/PCINT5)
DNC
DNC
DNC
PA6
20
19
18
17
16
Pin16: PA6 (PCINT6/OC1A/SDA/MOSI/ADC6)
Pin20: PA5 (ADC5/DO/MISO/OC1B/PCINT5)
2
14
PB2 (PCINT10/INT0/OC0A/CKOUT)
(ADCV2/AIN1/PCINT2) PA2
3
13
PB3 (PCINT11/RESET/dW)
(ADC1/AIN0/PCINT1) PA1
4
12
PB1 (PCINT9/XTAL2)
(ADC0/AREF/PCINT0) PA0
5
11
PB0 (PCINT8/XTAL1)
Bottom pad should be
soldered to ground
DNC: Do Not Connect
6
7
8
9
10
DNC
(ADC3//AT0/PCINT3) PA3
VCC
PA7 (PCINT7/ICP/OC0B/ADC7)
GND
15
DNC
1
DNC
(ADC4/USCK/SCL/PCINT4) PA4
Note
1.1
PA5
QFN/MLF
Disclaimer
Typical values contained in this data sheet are based on simulations and characterization of actual Atmel® ATtiny24/44/84
AVR® microcontrollers manufactured on the typical process technology. Applicable automotive min. and max. values will be
available after devices representative of the whole process excursion (corner run) have been characterized.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
3
2.
Overview
The Atmel® ATtiny24/44/84 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By
executing powerful instructions in a single clock cycle, the Atmel ATtiny24/44/84 achieves throughputs approaching 1MIPS
per MHz allowing the system designer to optimize power consumption versus processing speed.
4
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Block Diagram
Figure 2-1. Block Diagram
VCC
8-bit Databus
GND
Internal
Oscillator
Internal
Calibrated
Oscillator
Timing and
Control
Program
Counter
Stack
Pointer
Watchdog
Timer
Program
Flash
SRAM
MCU Control
Register
Instruction
Register
MCU Status
Register
General
Purpose
Registers
Timer/
Counter 0
X
Y
Z
Instruction
Decoder
Timer/
Counter 1
Control
Lines
ALU
Status
Register
Interrupt
Unit
Programming
Logic
+ -
Analog
Comparator
2.1
ISP
Interface
Data Register
Port A
Data Dir. Register
Port A
EEPROM
ADC
Oscillators
Data Register
Port B
Data Dir. Register
Port B
Port A Drivers
Port B Drivers
PA7-PA0
PB3-PB0
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
5
The Atmel® AVR® core combines a rich instruction set with 32 general purpose working registers. All 32 registers are directly
connected to the arithmetic logic unit (ALU), allowing two independent registers to be accessed in one single instruction
executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times
faster than conventional CISC microcontrollers.
The Atmel ATtiny24/44/84 provides the following features: 2/4/8K bytes of in-system programmable flash, 128/256/512 bytes
EEPROM, 128/256/512 bytes SRAM, 12 general purpose I/O lines, 32 general purpose working registers, an 8-bit
Timer/Counter with two PWM channels, a 16-bit Timer/Counter with two PWM channels, internal and external interrupts, an
8-channel 10-bit ADC, programmable gain stage (1x, 20x) for 12 differential ADC channel pairs, a programmable watchdog
timer with internal oscillator, internal calibrated oscillator, and three software selectable power saving modes. The idle mode
stops the CPU while allowing the SRAM, Timer/Counter, ADC, analog comparator, and interrupt system to continue
functioning. The power-down mode saves the register contents, disabling all chip functions until the next interrupt or
hardware reset. The ADC noise reduction mode stops the CPU and all I/O modules except ADC to minimize switching noise
during ADC conversions. In standby mode, the crystal/resonator oscillator is running while the rest of the device is sleeping.
This allows very fast start-up combined with low power consumption.
The device is manufactured using Atmel's high-density non-volatile memory technology. The on-chip ISP flash allows the
program memory to be re-programmed in-system through an SPI serial interface, by a conventional non-volatile memory
programmer or by an on-chip boot code running on the AVR core.
The Atmel ATtiny24/44/84 AVR is supported with a full suite of program and system development tools including: C
compilers, macro assemblers, program debugger/simulators, in-circuit emulators, and evaluation kits.
2.2
Automotive Quality Grade
The Atmel ATtiny24/44/84 has been developed and manufactured according to the most stringent requirements of the
international standard ISO-TS-16949 grade 1. This data sheet contains limit values extracted from the results of extensive
characterization (temperature and voltage). The quality and reliability of the Atmel ATtiny24/44/84 have been verified during
regular product qualification as per AEC-Q100.
As indicated in the ordering information paragraph, the product is available in only one temperature grade.
Table 2-1.
Temperature Grade Identification for Automotive Products
Temperature
Temperature Identifier
Comments
–40; +125
Z
Full automotive temperature range
2.3
Pin Descriptions
2.3.1
VCC
Supply voltage.
2.3.2
GND
Ground.
2.3.3
Port B (PB3...PB0)
Port B is a 4-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have
symmetrical drive characteristics with both high sink and source capability except PB3, which has the RESET capability. To
use pin PB3 as an I/O pin instead of RESET pin, program (‘0’) RSTDISBL fuse. As inputs, Port B pins that are externally
pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition
becomes active, even if the clock is not running.
Port B also serves the functions of various special features of the Atmel ATtiny24/44/84 as listed on Section 12.3
“Alternate Port Functions” on page 54.
6
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
2.3.4
RESET
Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not
running. The minimum pulse length is given in Table 9-1 on page 37. Shorter pulses are not guaranteed to generate a reset.
2.3.5
Port A (PA7...PA0)
Port A is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The port A output buffers have
symmetrical drive characteristics with both high sink and source capability. As inputs, Port A pins that are externally pulled
low will source current if the pull-up resistors are activated. The port A pins are tri-stated when a reset condition becomes
active, even if the clock is not running.
Port A has an alternate function as analog input for the ADC, analog comparator, Timer/Counter, SPI and pin change
interrupt as described in Section 12.3 “Alternate Port Functions” on page 54.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
7
3.
Resources
A comprehensive set of development tools, driver and application notes, and datasheets are available for download on
http://www.atmel.com/avr.
4.
About Code Examples
This documentation contains simple code examples that briefly show how to use various parts of the device. These code
examples assume that the part-specific header file is included before compilation. Be aware that not all C compiler vendors
include bit definitions in the header files, and interrupt handling in C is compiler dependent. Please confirm with the C
compiler documentation for more details.
For I/O registers located in the extended I/O map, IN, OUT, SBIS, SBIC, CBI, and SBI instructions must be replaced with
instructions that allow access to extended I/O, typically LDS and STS combined with SBRS, SBRC, SBR, and CBR.
8
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
5.
CPU Core
5.1
Overview
This section discusses the Atmel® AVR® core architecture in general. The main function of the CPU core is to ensure correct
program execution. The CPU must, therefore, be able to access memories, perform calculations, control peripherals, and
handle interrupts.
Architectural Overview
Figure 5-1. Block Diagram of the AVR Architecture
Data Bus 8-bit
Flash
Program
Memory
Program
Counter
Status and
Control
32 x 8
General
Purpose
Registers
Instruction
Decoder
Control Lines
Indirect Addressing
Instruction
Register
Direct Addressing
5.2
ALU
Interrupt
Unit
Watchdog
Timer
Analog
Comparator
Timer/Counter 0
Data
SRAM
Timer/Counter 1
EEPROM
Universal
Serial Interface
I/O Lines
In order to maximize performance and parallelism, the AVR uses a Harvard architecture, with separate memories and buses
for program and data. Instructions in the program memory are executed with a single-level pipelining. While one instruction
is being executed, the next instruction is pre-fetched from the program memory. This concept enables instructions to be
executed in every clock cycle. The program memory is in-system reprogrammable flash memory.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
9
The fast-access register file contains 32 x 8-bit general purpose working registers with a single clock cycle access time. This
allows single-cycle arithmetic logic unit (ALU) operation. In a typical ALU operation, two operands are output from the
register file, the operation is executed, and the result is stored back in the register file, all in one clock cycle.
Six of the 32 registers can be used as three 16-bit indirect address register pointers for data space addressing, enabling
efficient address calculations. One of the address pointers can also be used as an address pointer for look up tables in flash
program memory. These added function registers are the 16-bit X-, Y-, and Z-registers, described later in this section.
The ALU supports arithmetic and logic operations between registers or between a constant and a register. Single-register
operations can also be executed in the ALU. After an arithmetic operation, the status register is updated to reflect
information about the result of the operation.
Program flow is provided by conditional and unconditional jump and call instructions able to directly address the whole
address space. Most AVR® instructions have a single 16-bit word format. Every program memory address contains a 16- or
32-bit instruction.
During interrupts and subroutine calls, the return address program counter (PC) is stored on the stack. The stack is
effectively allocated in the general data SRAM, and consequently the stack size is only limited by the total SRAM size and
the usage of the SRAM. All user programs must initialize the stack pointer (SP) in the reset routine (before subroutines or
interrupts are executed). The SP is read/write accessible in the I/O space. The data SRAM can easily be accessed through
the five different addressing modes supported in the AVR architecture.
The memory spaces in the Atmel® AVR architecture are all linear and regular memory maps.
A flexible interrupt module has its control registers in the I/O space with an additional global interrupt enable bit in the status
register. All interrupts have a separate interrupt vector in the interrupt vector table. The interrupts have priority in accordance
with their interrupt vector position. The lower the interrupt vector address, the higher the priority.
The I/O memory space contains 64 addresses for CPU peripheral functions such as control registers, SPI, and other I/O
functions. The I/O memory can be accessed directly or as the data space locations following those of the register file,
0x20 - 0x5F.
5.3
ALU – Arithmetic Logic Unit
The high-performance Atmel AVR ALU operates in direct connection with all 32 general purpose working registers. Within a
single clock cycle, arithmetic operations between general purpose registers or between a register and an immediate are
executed. The ALU operations are divided into three main categories - arithmetic, logical, and bit functions. Some
implementations of the architecture also provide a powerful multiplier supporting both signed/unsigned multiplication and
fractional format. See the “Instruction Set” section for a detailed description.
5.4
Status Register
The status register contains information about the result of the most recently executed arithmetic instruction. This
information can be used for altering program flow in order to perform conditional operations. Note that the status register is
updated after all ALU operations, as specified in the instruction set summary. This will in many cases remove the need for
using the dedicated compare instructions, resulting in faster and more compact code.
The status register is not automatically stored when entering an interrupt routine and restored when returning from an
interrupt. This must be handled by software.
10
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
5.4.1
SREG – AVR Status Register
Bit
7
6
5
4
3
2
1
0
0x3F (0x5F)
I
T
H
S
V
N
Z
C
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
SREG
• Bit 7 – I: Global Interrupt Enable
The global interrupt enable bit must be set for the interrupts to be enabled. The individual interrupt enable control is then
performed in separate control registers. If the global interrupt enable register is cleared, none of the interrupts are enabled
independently of the individual interrupt enable settings. The I-bit is cleared by hardware after an interrupt has occurred, and
is set by the RETI instruction to enable subsequent interrupts. The I-bit can also be set and cleared by the application with
the SEI and CLI instructions, as described in the instruction set summary.
• Bit 6 – T: Bit Copy Storage
The bit copy instructions BLD (Bit LoaD) and BST (Bit STore) use the T-bit as source or destination for the operated bit. A bit
from a register in the register file can be copied into T by the BST instruction, and a bit in T can be copied into a bit in a
register in the register file by the BLD instruction.
• Bit 5 – H: Half Carry Flag
The half carry flag H indicates a half carry in some arithmetic operations. Half carry is useful in BCD arithmetic. See the
instruction set reference for detailed information.
• Bit 4 – S: Sign Bit, S = N V
The S-bit is always an exclusive OR between the negative flag N and the two's complement overflow flag V. See the
“Instruction Set Description” for detailed information.
• Bit 3 – V: Two’s Complement Overflow Flag
The two's complement overflow flag V supports two's complement arithmetic. See the instruction set summary for detailed
information.
• Bit 2 – N: Negative Flag
The negative flag N indicates a negative result in an arithmetic or logic operation. See the instruction set summary for
detailed information.
• Bit 1 – Z: Zero Flag
The zero flag Z indicates a zero result in an arithmetic or logic operation. See the instruction set summary for detailed
information.
• Bit 0 – C: Carry Flag
The carry flag C indicates a carry in an arithmetic or logic operation. See the instruction set summary for detailed
information.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
11
5.5
General Purpose Register File
The register file is optimized for the Atmel® AVR® Enhanced RISC instruction set. In order to achieve the required
performance and flexibility, the following input/output schemes are supported by the register file:
● One 8-bit output operand and one 8-bit result input
●
●
●
Two 8-bit output operands and one 8-bit result input
Two 8-bit output operands and one 16-bit result input
One 16-bit output operand and one 16-bit result input
Figure 5-2 on page 12 shows the structure of the 32 general purpose working registers in the CPU.
Figure 5-2. AVR CPU General Purpose Working Registers
7
0
Addr.
R0
0x00
R1
0x01
R2
0x02
…
R13
0x0D
General
R14
0x0E
Purpose
R15
0x0F
Working
R16
0x10
Registers
R17
0x11
…
R26
0x1A
X-register Low Byte
R27
0x1B
X-register High Byte
R28
0x1C
Y-register Low Byte
R29
0x1D
Y-register High Byte
R30
0x1E
Z-register Low Byte
R31
0x1F
Z-register High Byte
Most of the instructions operating on the register file have direct access to all registers, and most of them are single cycle
instructions.
As shown in Figure 5-2, each register is also assigned a data memory address, mapping them directly into the first 32
locations of the user data space. Although not physically implemented as SRAM locations, this memory organization
provides great flexibility in access of the registers, as the X-, Y- and Z-registers can be set to index any register in the file.
12
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
5.5.1
The X-register, Y-register, and Z-register
The registers R26..R31 have some added functions to their general purpose usage. These registers are 16-bit address
pointers for indirect addressing of the data space. The three indirect address registers X, Y, and Z are defined as described
in Figure 5-3 on page 13.
Figure 5-3. The X-, Y-, and Z-registers
15
XH
XL
0
7
0
7
0
X-register
R27 (0x1B)
R26 (0x1A)
15
YH
YL
0
7
0
7
0
Y-register
R29 (0x1D)
R28 (0x1C)
15
ZH
ZL
0
7
0
7
0
Z-register
R31 (0x1F)
R30 (0x1E)
In the different addressing modes, these address registers have functions as fixed displacement, automatic increment, and
automatic decrement (see the instruction set summary for details).
5.6
Stack Pointer
The stack is mainly used for storing temporary data, for storing local variables, and for storing return addresses after
interrupts and subroutine calls. The stack pointer register always points to the top of the stack. Note that the stack is
implemented as growing from higher memory locations to lower memory locations. This implies that a stack PUSH
instruction decreases the stack pointer.
The stack pointer points to the data SRAM stack area where the subroutine and interrupt stacks are located. This stack
space in the data SRAM must be defined by the program before any subroutine calls are executed or interrupts are enabled.
The stack pointer must be set to point above 0x60. The stack pointer is decremented by one when data are pushed onto the
stack with the PUSH instruction, and it is decremented by two when the return address is pushed onto the stack with a
subroutine call or interrupt. The stack pointer is incremented by one when data are popped from the stack with the POP
instruction, and it is incremented by two when data are popped from the stack with a return from subroutine RET instruction
or return from interrupt RETI instruction.
The Atmel AVR® stack pointer is implemented as two 8-bit registers in the I/O space. The number of bits actually used is
implementation dependent. Note that the data space in some implementations of the AVR architecture is so small that only
the SPL register is needed. In this case, the SPH register will not be present.
5.6.1
SPH and SPL – Stack Pointer High and Low
Bit
15
14
13
12
11
10
9
8
0x3E (0x5E)
SP15
SP14
SP13
SP12
SP11
SP10
SP9
SP8
SPH
0x3D (0x5D)
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0
SPL
7
6
5
4
3
2
1
0
Read/Write
Initial Value
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
13
5.7
Instruction Execution Timing
This section describes the general access timing concepts for instruction execution. The Atmel® AVR® CPU is driven by the
CPU clock clkCPU, directly generated from the selected clock source for the chip. No internal clock division is used.
Figure 5-4 shows the parallel instruction fetches and instruction executions enabled by the Harvard architecture and the fast
access register file concept. This is the basic pipelining concept to obtain up to 1MIPS per MHz with the corresponding
unique results for functions per cost, functions per clocks, and functions per power-unit.
Figure 5-4. The Parallel Instruction Fetches and Instruction Executions
T1
T2
T3
T4
clkCPU
1st Instruction Fetch
1st Instruction Execute
2nd Instruction Fetch
2nd Instruction Execute
3rd Instruction Fetch
3rd Instruction Execute
4th Instruction Fetch
Figure 5-5 shows the internal timing concept for the register file. In a single clock cycle an ALU operation using two register
operands is executed, and the result is stored back to the destination register.
Figure 5-5. Single-cycle ALU Operation
T1
T2
T3
T4
clkCPU
Total Execution Time
Register Operands Fetch
ALU Operation Execute
Result Write Back
5.8
Reset and Interrupt Handling
The Atmel AVR provides several different interrupt sources. These interrupts and the separate reset vector each have a
separate program vector in the program memory space. All interrupts are assigned individual enable bits which must be
written with a logical one together with the global interrupt enable bit in the status register in order to enable the interrupt.
The lowest addresses in the program memory space are by default defined as the reset and interrupt vectors. The complete
list of vectors is shown in Section 10. “Interrupts” on page 44. The list also determines the priority levels of the different
interrupts. The lower the address, the higher the priority level. RESET has the highest priority, and next is INT0, the external
interrupt request 0.
When an interrupt occurs, the global interrupt enable I-bit is cleared and all interrupts are disabled. The user software can
write a logical one to the I-bit to enable nested interrupts. All enabled interrupts can then interrupt the current interrupt
routine. The I-bit is automatically set when a return from interrupt instruction, RETI, is executed.
There are basically two types of interrupts. The first type is triggered by an event that sets the interrupt flag. For these
interrupts, the program counter is vectored to the actual interrupt vector in order to execute the interrupt handling routine,
and hardware clears the corresponding interrupt flag. Interrupt flags can also be cleared by writing a logic one to the flag bit
position(s) to be cleared. If an interrupt condition occurs while the corresponding interrupt enable bit is cleared, the interrupt
flag will be set and remembered until the interrupt is enabled or the flag is cleared by software. Similarly, if one or more
interrupt conditions occur while the global interrupt enable bit is cleared, the corresponding interrupt flag(s) will be set and
remembered until the global interrupt enable bit is set, and will then be executed by order of priority.
14
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
The second type of interrupt will trigger as long as the interrupt condition is present. These interrupts do not necessarily have
interrupt flags. If the interrupt condition disappears before the interrupt is enabled, the interrupt will not be triggered.
When the Atmel® AVR® exits from an interrupt, it will always return to the main program and execute one more instruction
before any pending interrupt is served.
Note that the status register is not automatically stored when entering an interrupt routine, nor restored when returning from
an interrupt routine. This must be handled by software.
When using the CLI instruction to disable interrupts, the interrupts will be immediately disabled. No interrupt will be executed
after the CLI instruction, even if it occurs simultaneously with the CLI instruction. The following example shows how this can
be used to avoid interrupts during the timed EEPROM write sequence.
Assembly Code Example
in
cli
sbi
sbi
out
r16, SREG
; store SREG value
; disable interrupts during timed sequence
EECR, EEMPE ; start EEPROM write
EECR, EEPE
SREG, r16
; restore SREG value (I-bit)
C Code Example
char cSREG;
cSREG = SREG; /* store SREG value */
/* disable interrupts during timed sequence */
_CLI();
EECR |= (1<<EEMPE); /* start EEPROM write */
EECR |= (1<<EEPE);
SREG = cSREG; /* restore SREG value (I-bit) */
When using the SEI instruction to enable interrupts, the instruction following SEI will be executed before any pending
interrupts, as shown in this example.
Assembly Code Example
sei
; set Global Interrupt Enable
sleep ; enter sleep, waiting for interrupt
; note: will enter sleep before any pending
; interrupt(s)
C Code Example
_SEI(); /* set Global Interrupt Enable */
_SLEEP(); /* enter sleep, waiting for interrupt */
/* note: will enter sleep before any pending interrupt(s) */
5.8.1
Interrupt Response Time
The interrupt execution response for all the enabled Atmel AVR interrupts is four clock cycles minimum. After four clock
cycles the program vector address for the actual interrupt handling routine is executed. During this four clock-cycle period,
the program counter is pushed onto the stack. The vector is normally a jump to the interrupt routine, and this jump takes
three clock cycles. If an interrupt occurs during execution of a multi-cycle instruction, this instruction is completed before the
interrupt is served. If an interrupt occurs when the MCU is in sleep mode, the interrupt execution response time is increased
by four clock cycles. This increase comes in addition to the start-up time from the selected sleep mode.
A return from an interrupt handling routine takes four clock cycles. During these four clock cycles, the program counter (two
bytes) is popped back from the stack, the stack pointer is incremented by two, and the I-bit in SREG is set.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
15
6.
Memories
This section describes the different memories in the Atmel® ATtiny24/44/84. The AVR® architecture has two main memory
spaces, the data memory space and the program memory space. In addition, the Atmel ATtiny24/44/84 features an
EEPROM memory for data storage. All three memory spaces are linear and regular.
6.1
In-System Re-programmable Flash Program Memory
The Atmel ATtiny24/44/84 contains 2/4/8K bytes of on-chip, in-system, reprogrammable flash memory for program storage.
Since all AVR instructions are 16 or 32 bits wide, the flash memory is organized as 1024/2048/4096 x 16.
The flash memory has an endurance of at least 10,000 write/erase cycles. The Atmel ATtiny24/44/84 program counter (PC)
is 10/11/12 bits wide, thus addressing the 1024/2048/4096 program memory locations. Section 21. “Memory Programming”
on page 141 contains a detailed description on flash data serial downloading using the SPI pins.
Constant tables can be allocated within the entire program memory address space (see the LPM – load program memory
instruction description).
Timing diagrams for instruction fetch and execution are presented in Section 5.7 “Instruction Execution Timing” on page 14.
Figure 6-1. Program Memory Map
Program Memory
0x0000
0x03FF/0x07FF/0xFFF
6.2
SRAM Data Memory
Figure 6-2 on page 17 shows how the ATtiny24/44/84 SRAM memory is organized.
The lower 160 data memory locations address the register file, the I/O memory, and the internal data SRAM. The first 32
locations address the register file, the next 64 locations the standard I/O memory, and the last 128/256/512 locations
address the internal data SRAM.
The five different addressing modes for the data memory are: direct, indirect with displacement, indirect, indirect with
pre-decrement, and indirect with post-increment. In the register file, registers R26 to R31 feature the indirect addressing
pointer registers.
The direct addressing mode reaches the entire data space.
The indirect with displacement mode reaches 63 address locations starting from the base address given by the Y- or
Z-register.
When using register indirect addressing modes with automatic pre-decrement and post-increment, the address registers X,
Y, and Z are decremented or incremented.
The 32 general purpose working registers, 64 I/O registers, and 128/256/512 bytes of internal data SRAM in the Atmel
ATtiny24/44/84 are all accessible through all these addressing modes. The register file is described in Section 5.5 “General
Purpose Register File” on page 12.
16
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Figure 6-2. Data Memory Map
Data Memory
32 Registers
0x0000 - 0x001F
64 I/O Registers
0x0020 - 0x005F
0x0060
Internal SRAM
(128/256/512 x 8)
0x0DF/0x015F/0x025F
6.2.1
Data Memory Access Times
This section describes the general access timing concepts for internal memory access. The internal data SRAM access is
performed in two clkCPU cycles as described in Figure 6-3.
Figure 6-3. On-chip Data SRAM Access Cycles
T1
T2
T3
clkCPU
Address
Compute Address
Address valid
Data
Write
WR
Data
Read
RD
Memory Access Instruction
6.3
Next Instruction
EEPROM Data Memory
The Atmel® ATtiny24/44/84 contains 128/256/512 bytes of EEPROM data memory. It is organized as a separate data space
in which single bytes can be read and written. The EEPROM has an endurance of at least 100,000 write/erase cycles. The
access between the EEPROM and the CPU is described in the following sections specifying the EEPROM address
registers, the EEPROM data register, and the EEPROM control register. For a detailed description of serial data
downloading to the EEPROM, see Section 21.6 “Serial Downloading” on page 144.
6.3.1
EEPROM Read/Write Access
The EEPROM access registers are accessible in the I/O space.
The write access times for the EEPROM are given in Table 6-1 on page 22. A self-timing function, however, lets the user
software detect when the next byte can be written. If the user code contains instructions that write to the EEPROM, some
precautions must be taken. In heavily filtered power supplies, VCC is likely to rise or fall slowly on power-up/down. This
causes the device for some period of time to run at a voltage lower than the specified minimum for the clock frequency used.
See Section 6.3.6 “Preventing EEPROM Corruption” on page 20 for details on how to avoid problems in these situations.
In order to prevent unintentional EEPROM writes, a specific write procedure must be followed. See Section 6.3.2 “Atomic
Byte Programming” on page 18 and Section 6.3.3 “Split Byte Programming” on page 18 for details on this.
When the EEPROM is read, the CPU is halted for four clock cycles before the next instruction is executed. When the
EEPROM is written, the CPU is halted for two clock cycles before the next instruction is executed.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
17
6.3.2
Atomic Byte Programming
Atomic byte programming is the simplest mode. When writing a byte to the EEPROM, the user must write the address into
the EEARL register and data into EEDR register. If the EEPMn bits are zero, writing EEPE (within four cycles after EEMPE
is written) will trigger the erase/write operation. Both the erase and write cycle are done in one operation and the total
programming time is given in Table 1. The EEPE bit remains set until the erase and write operations are completed. While
the device is busy with programming, it is not possible to do any other EEPROM operations.
6.3.3
Split Byte Programming
It is possible to split the erase and write cycle into two different operations. This may be useful if the system requires short
access time for some limited period of time (typically if the power supply voltage falls). In order to take advantage of this
method, the locations to be written are required to have been erased before the write operation. But because the erase and
write operations are split, it is possible to do the erase operations when the system allows time-critical operations to be done
(typically after power-up).
6.3.4
Erase
To erase a byte, the address must be written to EEAR. If the EEPMn bits are 0b01, writing the EEPE (within four cycles after
EEMPE is written) will trigger the erase operation only (programming time is given in Table 1). The EEPE bit remains set
until the erase operation completes. While the device is busy programming, it is not possible to do any other EEPROM
operations.
6.3.5
Write
To write a location, the user must write the address into EEAR and the data into EEDR. If the EEPMn bits are 0b10, writing
the EEPE (within four cycles after EEMPE is written) will trigger the write operation only (programming time is given in Table
1). The EEPE bit remains set until the write operation completes. If the location to be written has not been erased before
write, the data that is stored must be considered as lost. While the device is busy with programming, it is not possible to do
any other EEPROM operations.
The calibrated oscillator is used to time the EEPROM accesses. Make sure the oscillator frequency is within the
requirements described in Section 7.10.1 “Oscillator Calibration Register – OSCCAL” on page 29.
18
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
The following code examples show one assembly function and one C function for erase, write, or atomic write of the
EEPROM. The examples assume that interrupts are controlled (e.g., by disabling interrupts globally) so that no interrupts will
occur during execution of these functions.
Assembly Code Example
EEPROM_write:
; Wait for completion of previous write
sbic
EECR,EEPE
rjmp
EEPROM_write
; Set Programming mode
ldi
r16, (0<<EEPM1)|(0<<EEPM0)
out
EECR, r16
; Set up address (r17) in address register
out
EEARL, r17
; Write data (r16) to data register
out
EEDR,r16
; Write logical one to EEMPE
sbi
EECR,EEMPE
; Start eeprom write by setting EEPE
sbi
EECR,EEPE
ret
C Code Example
void EEPROM_write(unsigned char ucAddress, unsigned char ucData)
{
/* Wait for completion of previous write */
while(EECR & (1<<EEPE))
;
/* Set Programming mode */
EECR = (0<<EEPM1)|(0>>EEPM0)
/* Set up address and data registers */
EEARL = ucAddress;
EEDR = ucData;
/* Write logical one to EEMPE */
EECR |= (1<<EEMPE);
/* Start eeprom write by setting EEPE */
EECR |= (1<<EEPE);
}
Note:
The code examples are only valid for Atmel® ATtiny24 and Atmel ATtiny44, using 8-bit addressing mode.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
19
The next code examples show assembly and C functions for reading the EEPROM. The examples assume that interrupts
are controlled so that no interrupts will occur during execution of these functions.
Assembly Code Example
EEPROM_read:
; Wait for completion of previous write
sbic
EECR,EEPE
rjmp
EEPROM_read
; Set up address (r17) in address register
out
EEARL, r17
; Start eeprom read by writing EERE
sbi
EECR,EERE
; Read data from data register
in
r16,EEDR
ret
C Code Example
unsigned char EEPROM_read(unsigned char ucAddress)
{
/* Wait for completion of previous write */
while(EECR & (1<<EEPE))
;
/* Set up address register */
EEARL = ucAddress;
/* Start eeprom read by writing EERE */
EECR |= (1<<EERE);
/* Return data from data register */
return EEDR;
}
Note:
6.3.6
The code examples are only valid for Atmel® ATtiny24 and Atmel ATtiny44, using 8-bit addressing mode.
Preventing EEPROM Corruption
During periods of low VCC, the EEPROM data can be corrupted because the supply voltage is too low for the CPU and the
EEPROM to operate properly. A regular write sequence to the EEPROM requires a minimum voltage to operate correctly,
and the CPU itself can execute instructions incorrectly if the supply voltage is too low. These issues are the same as for
board level systems using EEPROM, and the same design solutions should be applied.
EEPROM data corruption can easily be avoided by following this design recommendation: Keep the AVR® RESET active
(low) during periods of insufficient power supply voltage. This can be done by enabling the internal brown-out detector
(BOD). If the detection level of the internal BOD does not match the needed detection level, an external low –VCC reset
protection circuit can be used. If a reset occurs while a write operation is in progress, the write operation will be completed
provided the power supply voltage is sufficient.
6.4
I/O Memory
The I/O space definition of the Atmel ATtiny24/44/84 is shown in Section 23-43 “Minimum Reset Pulse Width versus VCC” on
page 181.
All Atmel ATtiny24/44/84 I/Os and peripherals are placed in the I/O space. All I/O locations may be accessed by the
LD/LDS/LDD and ST/STS/STD instructions, transferring data between the 32 general purpose working registers and the I/O
space. I/O registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In
these registers, the value of single bits can be checked by using the SBIS and SBIC instructions. See the instruction set
summary for more details. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be
used. When addressing I/O registers as data space using LD and ST instructions, 0x20 must be added to these addresses.
For compatibility with future devices, reserved bits should be written with a logical zero if accessed. Reserved I/O memory
addresses should never be written.
20
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Some of the status flags are cleared by writing a logical one to them. Note that, unlike most other AVR®s, the CBI and SBI
instructions will only operate on the specified bit, and can, therefore, be used on registers containing such status flags. The
CBI and SBI instructions work with registers 0x00 to 0x1F only.
The I/O and peripherals control registers are explained in later sections.
6.4.1
General Purpose I/O Registers
The ATtiny24/44/84 contains three general purpose I/O registers. These registers can be used for storing any information,
and they are particularly useful for storing global variables and status flags. General purpose I/O registers within the address
range 0x00 - 0x1F are directly bit-accessible using the SBI, CBI, SBIS, and SBIC instructions.
6.5
Register Description
6.5.1
EEARH – EEPROM Address Register
Bit
7
6
5
4
3
2
1
0
0x1F (0x3F)
–
–
–
–
–
–
–
EEAR8
Read/Write
R
R
R
R
R
R
R
R/W
Initial Value
0
0
0
0
0
0
0
X
EEARH
• Bits 7..1 – Res: Reserved Bits
These are reserved bits in the ATtiny24/44/84, and will always read as zero.
• Bit 0 – EEAR8: EEPROM Address
The EEPROM address register, EEARH, specifies the most-significant bit for EEPROM address in the 512-byte EEPROM
space for Tiny84. This bit is reserved in the ATtiny24/44, and will always read as zero. The initial value of EEAR is
undefined. A proper value must be written before the EEPROM may be accessed.
6.5.2
EEARL – EEPROM Address Register
Bit
7
6
5
4
3
2
1
0
0x1E (0x3E)
EEAR7
EEAR6
EEAR5
EEAR4
EEAR3
EEAR2
EEAR1
EEAR0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
X
X
X
X
X
X
X
X
EEARL
• Bits 7..0 – EEAR7..0: EEPROM Address
The EEPROM address register, EEARL, specifies the EEPROM address. In the 128-byte EEPROM space in ATiny24, bit 7
is reserved and will always read as zero. The EEPROM data bytes are addressed linearly between 0 and 128/256/512. The
initial value of EEAR is undefined. A proper value must be written before the EEPROM may be accessed.
6.5.3
EEDR – EEPROM Data Register
Bit
7
6
5
4
3
2
1
0
0x1D (0x3D)
EEDR7
EEDR6
EEDR5
EEDR4
EEDR3
EEDR2
EEDR1
EEDR0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
EEDR
• Bits 7..0 – EEDR7..0: EEPROM Data
For the EEPROM write operation the EEDR register contains the data to be written to the EEPROM in the address given by
the EEAR register. For the EEPROM read operation, the EEDR contains the data read out from the EEPROM at the address
given by EEAR.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
21
6.5.4
EECR – EEPROM Control Register
Bit
7
6
5
4
3
2
1
0
0x1C (0x3C)
–
–
EEPM1
EEPM0
EERIE
EEMPE
EEPE
EERE
Read/Write
R
R
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
X
X
0
0
X
0
EECR
• Bit 7 – Res: Reserved Bit
This bit is reserved for future use, and will always read as 0 in Atmel® ATtiny24/44/84. For compatibility with future AVR®
devices, always write this bit to a logical zero. After reading, mask out this bit.
• Bit 6 – Res: Reserved Bit
This bit is reserved in the Atmel ATtiny24/44/84 and will always read as zero.
• Bits 5, 4 – EEPM1 and EEPM0: EEPROM Mode Bits
The EEPROM programming mode bits define which programming action will be triggered when writing EEPE. It is possible
to program data in one atomic operation (erase the old value and program the new value) or split the erase and write
operations into two separate operations. The programming times for the different modes are shown in Table 6-1. While
EEPE is set, any write to EEPMn will be ignored. During reset, the EEPMn bits will be reset to 0b00 unless the EEPROM is
busy programming.
Table 6-1.
EEPROM Mode Bits
EEPM1
EEPM0
0
0
Programming Time Operation
3.4ms
Erase and write in one operation (atomic operation)
0
1
1.8ms
Erase only
1
0
1.8ms
Write only
1
1
–
Reserved for future use
• Bit 3 – EERIE: EEPROM Ready Interrupt Enable
Writing EERIE to logical one enables the EEPROM ready interrupt if the I-bit in SREG is set. Writing EERIE to logical zero
disables the interrupt. The EEPROM ready interrupt generates a constant interrupt when non-volatile memory is ready for
programming.
• Bit 2 – EEMPE: EEPROM Master Program Enable
The EEMPE bit determines whether writing EEPE to logical one will have effect or not. When EEMPE is set, setting EEPE
within four clock cycles will program the EEPROM at the selected address. If EEMPE is logical zero, setting EEPE will have
no effect. When EEMPE has been written to logical one by software, hardware clears the bit to logical zero after four clock
cycles.
• Bit 1 – EEPE: EEPROM Program Enable
The EEPROM program enable bit, EEPE, is the programming enable signal to the EEPROM. When EEPE is written, the
EEPROM will be programmed according to the EEPMn bits setting. The EEMPE bit must be written to logical one before a
logical one is written to EEPE, otherwise no EEPROM write will take place. When the write access time has elapsed, the
EEPE bit is cleared by hardware. When EEPE has been set, the CPU is halted for two cycles before the next instruction is
executed.
• Bit 0 – EERE: EEPROM Read Enable
The EEPROM read enable signal, EERE, is the read strobe for the EEPROM. When the correct address is set up in the
EEAR register, the EERE bit must be written to logical one to trigger the EEPROM read. The EEPROM read access takes
one instruction, and the requested data are available immediately. When the EEPROM is read, the CPU is halted for four
cycles before the next instruction is executed. The user should poll the EEPE bit before starting the read operation. If a write
operation is in progress, it is not possible to read the EEPROM or change the EEAR register.
22
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
6.5.5
6.5.6
6.5.7
GPIOR2 – General Purpose I/O Register 2
Bit
7
0x15 (0x35)
MSB
6
5
4
3
2
1
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
3
2
1
LSB
GPIOR2
GPIOR1 – General Purpose I/O Register 1
Bit
7
0x14 (0x34)
MSB
6
5
4
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
3
2
1
LSB
GPIOR1
GPIOR0 – General Purpose I/O Register 0
Bit
7
0x13 (0x33)
MSB
6
5
4
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
LSB
GPIOR0
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
23
7.
System Clock and Clock Options
7.1
Clock Systems and their Distribution
Figure 7-1 presents the principal clock systems in the AVR® and their distribution. All of the clocks need not be active at a
given time. In order to reduce power consumption, the clocks to modules not being used can be halted by using different
sleep modes, as described in Section 8. “Power Management and Sleep Modes” on page 31. The clock systems are detailed
below.
Figure 7-1. Clock Distribution
ADC
General I/O
Modules
clkI/O
AVR Clock
Control Unit
clkADC
CPU Core
RAM
Flash and
EEPROM
clkCPU
clkFLASH
Reset Logic
Source clock
Watchdog Timer
Watchdog clock
System Clock
Prescaler
Watchdog
Oscillator
Clock
Multiplexer
External Clock
7.1.1
Crystal
Oscillator
Low-frequency
Crystal Oscillator
Calibrated RC
Oscillator
CPU Clock – clkCPU
The CPU clock is routed to parts of the system concerned with operation of the AVR core. Examples of such modules are
the general purpose register file, the status register and the data memory holding the stack pointer. Halting the CPU clock
inhibits the core from performing general operations and calculations.
7.1.2
I/O Clock – clkI/O
The I/O clock is used by the majority of the I/O modules, like the Timer/Counter. The I/O clock is also used by the external
interrupt module, but note that some external interrupts are detected by asynchronous logic, allowing such interrupts to be
detected even if the I/O clock is halted.
7.1.3
Flash Clock – clkFLASH
The flash clock controls operation of the flash interface. The flash clock is usually active simultaneously with the CPU clock.
24
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
7.1.4
ADC Clock – clkADC
The ADC is provided with a dedicated clock domain. This allows halting the CPU and I/O
clocks in order to reduce noise generated by their digital circuitry. This gives more accurate ADC conversion results.
7.2
Clock Sources
The device has the following clock source options, selectable by flash fuse bits as shown below. The clock from the selected
source is input to the Atmel® AVR® clock generator, and routed to the appropriate modules.
Table 7-1.
Device Clocking Options Select(1)
Device Clocking Option
CKSEL3..0
External clock
0000
Calibrated internal RC oscillator 8.0MHz
0010
Watchdog oscillator 128kHz
0100
External low-frequency oscillator
0110
External crystal/ceramic resonator
Reserved
Note:
1.
1000-1111
0101, 0111, 0011,0001
For all fuses “1” means unprogrammed while “0” means programmed.
The various choices for each clocking option is given in the following sections. When the CPU wakes up from power-down or
power-save, the selected clock source is used to time the start-up, ensuring stable oscillator operation before instruction
execution starts. When the CPU starts from reset, there is an additional delay allowing the power to reach a stable level
before commencing normal operation. The watchdog oscillator is used for timing this real-time part of the start-up time. The
number of WDT oscillator cycles used for each time-out is shown in Table 7-2.
Table 7-2.
7.3
Number of Watchdog Oscillator Cycles
Typ Time-out
Number of Cycles
4ms
512
64ms
8K (8,192)
Default Clock Source
The device is shipped with CKSEL = “0010”, SUT = “10”, and CKDIV8 programmed. The default clock source setting is
therefore the internal RC oscillator running at 8.0MHz with longest start-up time and an initial system clock prescaling of 8,
resulting in 1.0MHz system clock. This default setting ensures that all users can make their desired clock source setting
using an in-system or high-voltage programmer.
7.4
Crystal Oscillator
XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier which can be configured for use as an on-chip
oscillator, as shown in Figure 7-2 Either a quartz crystal or a ceramic resonator may be used.
C1 and C2 should always be equal for both crystals and resonators. The optimal value of the capacitors depends on the
crystal or resonator in use, the amount of stray capacitance, and the electromagnetic noise of the environment. Some initial
guidelines for choosing capacitors for use with crystals are given in Table 7-3 on page 26. For ceramic resonators, the
capacitor values given by the manufacturer should be used.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
25
Figure 7-2. Crystal Oscillator Connections
C2
XTAL2
C1
XTAL1
GND
The oscillator can operate in three different modes, each optimized for a specific frequency range. The operating mode is
selected by the fuses CKSEL3..1 as shown in Table 7-3.
Table 7-3.
Crystal Oscillator Operating Modes
CKSEL3..1
Frequency Range (MHz)
Recommended Range for Capacitors C1 and C2 for Use
with Crystals (pF)
100(1)
0.4 - 0.9
–
101
0.9 - 3.0
12 - 22
110
3.0 - 8.0
12 - 22
111
Note:
1.
8.0
12 - 22
This option should not be used with crystals, only with ceramic resonators.
The CKSEL0 fuse together with the SUT1..0 fuses select the start-up times as shown in Table 7-4.
Table 7-4.
Additional Delay from
Reset
(VCC = 5.0V)
CKSEL0
SUT1..0
Start-up Time from Powerdown and Power-save
0
00
258CK(1)
14CK + 4.1ms
Ceramic resonator, fast rising
power
0
01
258CK(1)
14CK + 65ms
Ceramic resonator, slowly rising
power
0
10
1KCK(2)
14CK
0
11
1KCK(2)
14CK + 4.1ms
Ceramic resonator, fast rising
power
1
00
1KCK(2)
14CK + 65ms
Ceramic resonator, slowly rising
power
1
01
16KCK
14CK
Crystal oscillator, BOD enabled
1
10
16KCK
14CK + 4.1ms
1
Notes:
1.
Recommended Usage
Ceramic resonator, BOD
enabled
Crystal oscillator, fast rising
power
Crystal oscillator, slowly rising
power
These options should only be used when not operating close to the maximum frequency of the device, and
only if frequency stability at start-up is not important for the application. These options are not suitable for
crystals.
11
2.
26
Start-up Times for the Crystal Oscillator Clock Selection
16KCK
14CK + 65ms
These options are intended for use with ceramic resonators and will ensure frequency stability at start-up.
They can also be used with crystals when not operating close to the maximum frequency of the device, and if
frequency stability at start-up is not important for the application.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
7.5
Low-frequency Crystal Oscillator
To use a 32.768kHz watch crystal as the clock source for the device, the low-frequency crystal oscillator must be selected by
setting CKSEL fuses to “0110”. The crystal should be connected as shown in Figure 7-2 on page 26. See the 32kHz crystal
oscillator application note for details on oscillator operation and how to choose appropriate values for C1 and C2.
When this oscillator is selected, start-up times are determined by the SUT fuses as shown in Table 7-5.
Table 7-5.
SUT1..0
Start-up Time from Power
Down and Power Save
Additional Delay from Reset
(VCC = 5.0V)
00
1KCK(1)
4ms
Fast rising power or BOD enabled
01
1KCK
(1)
64ms
Slowly rising power
10
32KCK
64ms
Stable frequency at start-up
11
Note:
7.6
Start-up Times for the Low Frequency Crystal Oscillator Clock Selection
1.
Recommended usage
Reserved
These options should only be used if frequency stability at start-up is not important for the application.
Calibrated Internal RC Oscillator
By default, the internal RC oscillator provides an approximate 8MHz clock. Though voltage and temperature dependent, this
clock can be very accurately calibrated by the user. See Table 22-2 on page 157 and Section 23.9 “Internal Oscillator Speed”
on page 176 for more details. The device is shipped with the CKDIV8 fuse programmed. See Section 7.9 “System Clock
Prescaler” on page 29 for more details.
This clock may be selected as the system clock by programming the CKSEL fuses as shown in Table 7-6. If selected, it will
operate with no external components. During reset, hardware loads the pre-programmed calibration value into the OSCCAL
register and thereby automatically calibrates the RC oscillator. The accuracy of this calibration is shown as factory calibration
in Table 22-2 on page 157.
By changing the OSCCAL register from SW, see Section 7.10.1 “Oscillator Calibration Register – OSCCAL” on page 29, it is
possible to get higher calibration accuracy than by using the factory calibration. The accuracy of this calibration is shown as
User calibration in Table 22-2 on page 157.When this oscillator is used as the chip clock, the watchdog oscillator will still be
used for the watchdog timer and for the reset time-out. For more information on the pre-programmed calibration value, see
the section Section 21.4 “Calibration Byte” on page 143.
Table 7-6.
Internal Calibrated RC Oscillator Operating Modes
CKSEL3..0
Nominal Frequency
(1)
Note:
1.
0010
The device is shipped with this option selected.
8.0 MHz
When this oscillator is selected, start-up times are determined by the SUT fuses as shown in Table 7-7.
Table 7-7.
Start-up Times for the Internal Calibrated RC Oscillator Clock Selection
SUT1..0
Start-up Time
from Power-down
Additional Delay from Reset
(VCC = 5.0V)
00
6 CK
14CK
01
6 CK
14CK + 4 ms
Fast rising power
14CK + 64 ms
Slowly rising power
10
(1)
6 CK
11
Note:
Recommended Usage
BOD enabled
Reserved
1.
The device is shipped with this option selected.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
27
7.7
External Clock
To drive the device from an external clock source, CLKI should be driven as shown in Figure 7-3. To run the device on an
external clock, the CKSEL fuses must be programmed to “0000”.
Figure 7-3. External Clock Drive Configuration
External
Clock
Signal
CLKI
GND
When this clock source is selected, start-up times are determined by the SUT fuses as shown in Table 7-8.
Table 7-8.
Start-up Times for the External Clock Selection
SUT1..0
Start-up Time from Power-down and
Power-save
Additional Delay from Reset
Recommended Usage
00
6CK
14CK
BOD enabled
01
6CK
14CK + 4ms
Fast rising power
10
6CK
14CK + 64ms
Slowly rising power
11
Reserved
When applying an external clock, sudden changes in the applied clock frequency must be avoided to ensure stable
operation of the MCU. A variation in frequency of more than 2% from one clock cycle to the next can lead to unpredictable
behavior. It is required to ensure that the MCU is kept in reset during such changes in the clock frequency.
Note that the system clock prescaler can be used to implement run-time changes of the internal clock frequency while still
ensuring stable operation. See Section 7.9 “System Clock Prescaler” on page 29 for details.
7.8
128kHz Internal Oscillator
The 128kHz internal oscillator is a low power oscillator providing a 128kHz clock. The frequency is nominal at 3V and 25°C.
This clock may be selected as the system clock by programming the CKSEL fuses to "0100".
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in Table 7-9.
Table 7-9.
Start-up Times for the 128kHz Internal Oscillator
SUT1..0
Start-up Time from Power-down and
Power-save
Additional Delay from Reset
Recommended Usage
00
6CK
14CK
BOD enabled
01
6CK
14CK + 4ms
Fast rising power
10
6CK
14CK + 64ms
Slowly rising power
11
28
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Reserved
7.9
System Clock Prescaler
The Atmel® ATtiny24/44/84 system clock can be divided by setting the clock prescaler register – CLKPR. This feature can be
used to decrease power consumption when the requirement for processing power is low. This can be used with all clock
source options, and it will affect the clock frequency of the CPU and all synchronous peripherals. clkI/O, clkADC, clkCPU, and
clkFLASH are divided by a factor as shown in Table 7-10 on page 30.
7.9.1
Switching Time
When switching between prescaler settings, the system clock prescaler ensures that no glitches occur in the clock system
and that no intermediate frequency is higher than either the clock frequency corresponding to the previous setting or the
clock frequency corresponding to the new setting.
The ripple counter that implements the prescaler runs at the frequency of the undivided clock, which may be faster than the
CPU's clock frequency. Hence, it is not possible to determine the state of the prescaler, even if it were readable, and the
exact time it takes to switch from one clock division to another cannot be exactly predicted.
From the time the CLKPS values are written, it takes between T1 + T2 and T1 + 2 T2 before the new clock frequency is
active. In this interval, twp active clock edges are produced. Here, T1 is the previous clock period, and T2 is the period
corresponding to the new prescaler setting.
7.10
Register Description
7.10.1 Oscillator Calibration Register – OSCCAL
Bit
7
6
5
4
3
2
1
0
0x31 (0x51)
CAL7
CAL6
CAL5
CAL4
CAL3
CAL2
CAL1
CAL0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
OSCCAL
Device Specific Calibration Value
The oscillator calibration register is used to trim the calibrated internal RC oscillator to remove process variations from the
oscillator frequency. A pre-programmed calibration value is automatically written to this register during chip reset, giving the
factory calibrated frequency as specified in Table 22-2 on page 157. The application software can write this register to
change the oscillator frequency. The oscillator can be calibrated to frequencies as specified in Table 22-2 on page 157.
calibration outside that range is not guaranteed.
Note that this oscillator is used to time EEPROM and flash write accesses, and these write times will be affected accordingly.
If the EEPROM or flash are written, do not calibrate to more than 8.8MHz. Otherwise, the EEPROM or flash write may fail.
The CAL7 bit determines the range of operation for the oscillator. Setting this bit to logical zero gives the lowest frequency
range, setting this bit to logical one gives the highest frequency range. The two frequency ranges are overlapping, in other
words a setting of OSCCAL = 0x7F gives a higher frequency than OSCCAL = 0x80.
The CAL6..0 bits are used to tune the frequency within the selected range. A setting of 0x00 gives the lowest frequency in
that range, and a setting of 0x7F gives the highest frequency in the range.
7.10.2 Clock Prescaler Register – CLKPR
Bit
7
6
5
4
0x26 (0x46)
CLKPCE
–
–
–
Read/Write
R/W
R
R
R
Initial Value
0
0
0
0
3
2
1
0
CLKPS3 CLKPS2 CLKPS1 CLKPS0
R/W
R/W
R/W
CLKPR
R/W
See Bit Description
• Bit 7 – CLKPCE: Clock Prescaler Change Enable
The CLKPCE bit must be written to logical one to enable change of the CLKPS bits. The CLK- PCE bit is only updated when
the other bits in CLKPR are simultaneously written to logical zero. CLKPCE is cleared by hardware four cycles after it is
written or when the CLKPS bits are written. Rewriting the CLKPCE bit within this time-out period does neither extend the
time-out period nor clear the CLKPCE bit.+
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
29
• Bits 6..4 – Res: Reserved Bits
These bits are reserved bits in the Atmel® ATtiny24/44/84 and will always read as zero.
• Bits 3..0 – CLKPS3..0: Clock Prescaler Select Bits 3 - 0
These bits define the division factor between the selected clock source and the internal system clock. These bits can be
written at run-time to vary the clock frequency to suit the application requirements. As the divider divides the master clock
input to the MCU, the speed of all synchronous peripherals is reduced when a division factor is used. The division factors are
given in Table 7-10.
To avoid unintentional changes of clock frequency, a special write procedure must be followed to change the CLKPS bits:
1. Write the Clock Prescaler Change Enable (CLKPCE) bit to one and all other bits in CLKPR to zero.
2.
Within four cycles, write the desired value to CLKPS while writing a zero to CLKPCE.
Interrupts must be disabled when changing prescaler setting to make sure the write procedure is not interrupted.
The CKDIV8 fuse determines the initial value of the CLKPS bits. If CKDIV8 is unprogrammed, the CLKPS bits will be reset to
“0000”. If CKDIV8 is programmed, CLKPS bits are reset to “0011”, giving a division factor of eight at start up. This feature
should be used if the selected clock source has a higher frequency than the maximum frequency of the device at the present
operating conditions. Note that any value can be written to the CLKPS bits regardless of the CKDIV8 fuse setting. The
application software must ensure that a sufficient division factor is chosen if the selected clock source has a higher
frequency than the maximum frequency of the device at the present operating conditions. The device is shipped with the
CKDIV8 fuse programmed.
Table 7-10. Clock Prescaler Select
30
CLKPS3
CLKPS2
CLKPS1
CLKPS0
Clock Division Factor
0
0
0
0
1
0
0
0
1
2
0
0
1
0
4
0
0
1
1
8
0
1
0
0
16
0
1
0
1
32
0
1
1
0
64
0
1
1
1
128
1
0
0
0
256
1
0
0
1
Reserved
1
0
1
0
Reserved
1
0
1
1
Reserved
1
1
0
0
Reserved
1
1
0
1
Reserved
1
1
1
0
Reserved
1
1
1
1
Reserved
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
8.
Power Management and Sleep Modes
Sleep modes enable the application to shut down unused modules in the MCU, thereby saving power. The Atmel® AVR®
provides various sleep modes allowing the user to tailor the power consumption to the application’s requirements.
8.1
Sleep Modes
Figure 7-1 on page 24 presents the different clock systems in the Atmel ATtiny24/44/84, and their distribution. The figure is
helpful in selecting an appropriate sleep mode. Table 8-1 shows the different sleep modes and their wake up sources
Active Clock Domains and Wake-up Sources in the Different Sleep Modes
Idle
X
ADC noise
Reduction
X
X
X
X
X
X
X(1)
X
X
X
X
Watchdog
Interrupt
Other I/O
X
X(1)
(2)
2.
ADC
X
Power-down
Stand-by
Notes: 1.
SPM/
EEPROM
Ready
clkADC
Sleep Mode
Wake-up Sources
INT0 and
Pin Change
Oscillators
clkIO
clkFLASH
clkCPU
Active Clock Domains
Main Clock
Source Enabled
Table 8-1.
X
X
X
X(1)
For INT0, only level interrupt.
Only recommended with external crystal or resonator selected as clock source
To enter any of the three sleep modes, the SE bit in MCUCR must be written to logic one and a SLEEP instruction must be
executed. The SM1..0 bits in the MCUCR register select which sleep mode (idle, ADC noise reduction, standby or
power-down) will be activated by the SLEEP instruction. See Table 8-2 on page 34 for a summary.
If an enabled interrupt occurs while the MCU is in a sleep mode, the MCU wakes up. The MCU is then halted for four cycles
in addition to the start-up time, executes the interrupt routine, and resumes execution from the instruction following SLEEP.
The contents of the register File and SRAM are unaltered when the device wakes up from sleep. If a reset occurs during
sleep mode, the MCU wakes up and executes from the reset vector.
8.2
Idle Mode
When the SM1..0 bits are written to “00”, the SLEEP instruction makes the MCU enter idle mode, stopping the CPU but
allowing the analog comparator, ADC, Timer/Counter, watchdog, and interrupt system to continue operating. This sleep
mode basically halts clkCPU and clkFLASH, while allowing the other clocks to run.
Idle mode enables the MCU to wake up from external triggered interrupts as well as internal ones like the timer overflow. If
wake-up from the analog comparator interrupt is not required, the analog comparator can be powered down by setting the
ACD bit in the analog comparator control and status register – ACSR. This will reduce power consumption in Idle mode. If
the ADC is enabled, a conversion starts automatically when this mode is entered.
8.3
ADC Noise Reduction Mode
When the SM1..0 bits are written to 01, the SLEEP instruction makes the MCU enter ADC noise reduction mode, stopping
the CPU but allowing the ADC, the external interrupts, and the Watchdog to continue operating (if enabled). This sleep mode
halts clkI/O, clkCPU, and
clkFLASH, while allowing the other clocks to run.
This improves the noise environment for the ADC, enabling higher resolution measurements. If the ADC is enabled, a
conversion starts automatically when this mode is entered. Apart from the ADC conversion complete interrupt, only an
external reset, a watchdog reset, a brown-out reset, an SPM/EEPROM ready interrupt, an external level interrupt on INT0 or
a pin change interrupt can wake up the MCU from ADC noise reduction mode.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
31
8.4
Power-down Mode
When the SM1..0 bits are written to “10”, the SLEEP instruction makes the MCU enter power-down mode. In this mode, the
oscillator is stopped, while the external interrupts and the watchdog continue operating (if enabled). Only an external reset, a
watchdog reset, a brown-out reset, an external level interrupt on INT0, or a pin change interrupt can wake up the MCU. This
sleep mode halts all generated clocks, allowing operation of asynchronous modules only.
Note that if a level triggered interrupt is used for wake-up from power-down mode, the changed level must be held for some
time to wake up the MCU. See Section 11. “External Interrupts” on page 46 for details
8.5
Standby Mode
When the SM1..0 bits are 11 and an external crystal/resonator clock option is selected, the SLEEP instruction makes the
MCU enter standby mode. This mode is identical to power-down with the exception that the oscillator is kept running. From
standby mode, the device wakes up in six clock cycles.
8.6
Software BOD Disable
When the brown-out detector (BOD) is enabled by BODLEVEL fuses (see Table 21-4 on page 142), the BOD is actively
monitoring the supply voltage during a sleep period. In some devices it is possible to save power by disabling the BOD by
software in power-down and stand-by sleep modes. The sleep mode power consumption will then be at the same level as
when BOD is globally disabled by fuses.
If BOD is disabled by software, the BOD function is turned off immediately after entering the sleep mode. Upon wake-up
from sleep, BOD is automatically enabled again. This ensures safe operation in case the VCC level has dropped during the
sleep period.
When the BOD has been disabled, the wake-up time from sleep mode will be approximately 60µs to ensure that the BOD is
working correctly before the MCU continues executing code.
BOD disable is controlled by the BODS (BOD Sleep) bit of MCU control register, see Section 8.9.1 “MCUCR – MCU Control
Register” on page 34. Writing this bit to one turns off BOD in power-down and stand-by, while writing a zero keeps the BOD
active. The default setting is zero, i.e. BOD active.
Writing to the BODS bit is controlled by a timed sequence and an enable bit, see Section 8.9.1 “MCUCR – MCU Control
Register” on page 34.
8.7
Power Reduction Register
The power reduction register (PRR), see Section 8.9.2 “PRR – Power Reduction Register” on page 35, provides a method to
stop the clock to individual peripherals to reduce power consumption. The current state of the peripheral is frozen and the I/O
registers cannot be read or written. Resources used by the peripheral when stopping the clock will remain occupied; hence
the peripheral should in most cases be disabled before stopping the clock. Waking up a module, which is done by clearing
the bit in PRR, puts the module in the same state as before shutdown.
Module shutdown can be used in idle mode and active mode to significantly reduce the overall power consumption. See
Section 23.4 “Power-down Supply Current” on page 168 for examples. In all other sleep modes, the clock is already stopped.
8.8
Minimizing Power Consumption
There are several issues to consider when trying to minimize the power consumption in an AVR®-controlled system. In
general, sleep modes should be used as much as possible, and the sleep mode should be selected so that as few of the
device's functions as possible are operating. All functions not needed should be disabled. In particular, the following modules
may need special consideration when trying to achieve the lowest possible power consumption.
8.8.1
Analog-to-Digital Converter
If enabled, the ADC will be enabled in all sleep modes. To save power, the ADC should be disabled before entering any
sleep mode. When the ADC is turned off and on again, the next conversion will be an extended conversion. See Section 18.
“Analog-to-Digital Converter” on page 118 for details on ADC operation.
32
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
8.8.2
Analog Comparator
When entering idle mode, the analog comparator should be disabled if not used. When entering ADC noise reduction mode,
the analog comparator should be disabled. In the other sleep modes, the analog comparator is automatically disabled.
However, if the analog comparator is set up to use the internal voltage reference as input, the analog comparator should be
disabled in all sleep modes. Otherwise, the internal voltage reference will be enabled, independent of sleep mode. See
Section 17. “Analog Comparator” on page 115 for details on how to configure the analog comparator.
8.8.3
Brown-out Detector
If the brown-out detector is not needed in the application, this module should be turned off. If the brown-out detector is
enabled by the BODLEVEL fuses, it will be enabled in all sleep modes, and hence, always consume power. In the deeper
sleep modes, this will contribute significantly to the total current consumption. See Section 9.5 “Brown-out Detection” on
page 38 for details on how to configure the brown-out detector.
8.8.4
Internal Voltage Reference
The internal voltage reference will be enabled when needed by the brown-out detection, the analog comparator or the ADC.
If these modules are disabled as described in the sections above, the internal voltage reference will be disabled and it will
not be consuming power. When turned on again, the user must allow the reference to start up before the output is used. If
the reference is kept on in sleep mode, the output can be used immediately. See Section 9.7 “Internal Voltage Reference” on
page 39 for details on the start-up time.
8.8.5
Watchdog Timer
If the watchdog timer is not needed in the application, this module should be turned off. If the watchdog timer is enabled, it
will be enabled in all sleep modes, and hence, always consume power. In the deeper sleep modes, this will contribute
significantly to the total current consumption. See Section 9.8 “Watchdog Timer” on page 39 for details on how to configure
the watchdog timer.
8.8.6
Port Pins
When entering a sleep mode, all port pins should be configured to use minimum power. The most important thing is then to
ensure that no pins drive resistive loads. In sleep modes where both the I/O clock (clkI/O) and the ADC clock (clkADC) are
stopped, the input buffers of the device will be disabled. This ensures that no power is consumed by the input logic when not
needed. In some cases, the input logic is needed for detecting wake-up conditions, and it will then be enabled. See the
section Section 12.2.5 “Digital Input Enable and Sleep Modes” on page 53 for details on which pins are enabled. If the input
buffer is enabled and the input signal is left floating or has an analog signal level close to VCC/2, the input buffer will use
excessive power.
For analog input pins, the digital input buffer should be disabled at all times. An analog signal level close to VCC/2 on an input
pin can cause significant current even in active mode. digital input buffers can be disabled by writing to the digital input
disable register (DIDR0). See Section 18.10.5 “DIDR0 – Digital Input Disable Register 0” on page 134 for details.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
33
8.9
Register Description
8.9.1
MCUCR – MCU Control Register
The MCU control register contains control bits for power management.
Bit
7
6
5
4
3
2
1
0
BODS
PUD
SE
SM1
SM0
BODSE
ISC01
ISC00
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
MCUCR
• Bit 7 – BODS: BOD Sleep
In order to disable BOD during sleep (see Table 8-1 on page 31) the BODS bit must be written to logic one. This is controlled
by a timed sequence and the enable bit, BODSE in MCUCR. First, both BODS and BODSE must be set to one. Second,
within four clock cycles, BODS must be set to one and BODSE must be set to zero. The BODS bit is active three clock
cycles after it is set. A sleep instruction must be executed while BODS is active in order to turn off the BOD for the actual
sleep mode. The BODS bit is automatically cleared after three clock cycles.
• Bit 5 – SE: Sleep Enable
The SE bit must be written to logical one to make the MCU enter the sleep mode when the SLEEP instruction is executed.
To avoid the MCU entering the sleep mode unless it is the programmer's purpose, it is recommended to set the sleep enable
(SE) bit just before the execution of the SLEEP instruction and to clear it immediately after waking up.
• Bits 4, 3 – SM1..0: Sleep Mode Select Bits 2..0
These bits select between the three available sleep modes as shown in Table 8-2.
Table 8-2.
Note:
Sleep Mode Select
SM1
SM0
Sleep Mode
0
0
Idle
0
1
ADC Noise Reduction
1
0
Power-down
1
1
Standby(1)
1. Only recommended with external crystal or resonator selected as clock source
• Bit 2 – BODSE: BOD Sleep Enable
The BODSE bit enables setting of BODS control bit, as explained on BODS bit description. BOD disable is controlled by a
timed sequence.
34
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
8.9.2
PRR – Power Reduction Register
Bit
7
6
5
4
3
2
1
0
–
–
–
–
PRTIM1
PRTIM0
PRUSI
PRADC
Read/Write
R
R
R
R
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
PRR
• Bits 7, 6, 5, 4- Res: Reserved Bits
These bits are reserved bits in the Atmel® ATtiny24/44/84 and will always read as zero.
• Bit 3- PRTIM1: Power Reduction Timer/Counter1
Writing a logical one to this bit shuts down the Timer/Counter 1 module. When the Timer/Counter 1 is enabled, operation will
continue like before the shutdown.
• Bit 2- PRTIM0: Power Reduction Timer/Counter0
Writing a logical one to this bit shut s down the Timer/Counter 0 module. When the Timer/Counter 0 is enabled, operation will
continue like before the shutdown.
• Bit 1 - PRUSI: Power Reduction USI
Writing a logic one to this bit shuts down the USI by stopping the clock to the module. When waking up the USI again, the
USI should be re initialized to ensure proper operation.
• Bit 0 - PRADC: Power Reduction ADC
Writing a logic one to this bit shuts down the ADC. The ADC must be disabled before shutdown. The analog comparator
cannot use the ADC input MUX when the ADC is shut down.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
35
9.
System Control and Reset
9.1
Resetting the AVR
During reset, all I/O registers are set to their initial values, and the program starts execution from the reset vector. The
instruction placed at the reset vector must be a RJMP – relative jump – instruction to the reset handling routine. If the
program never enables an interrupt source, the interrupt vectors are not used, and regular program code can be placed at
these locations. The circuit diagram in Figure 9-1 shows the reset logic. Table 9-1 on page 37 defines the electrical
parameters of the reset circuitry. The I/O ports of the Atmel® AVR® are immediately reset to their initial state when a reset
source goes active. This does not require any clock source to be running. After all reset sources have gone inactive, a delay
counter is invoked, stretching the internal reset. This allows the power to reach a stable level before normal operation starts.
The time-out period of the delay counter is defined by the user through the SUT and CKSEL fuses. The different selections
for the delay period are presented in Section 7.2 “Clock Sources” on page 25.
9.2
Reset Sources
The Atmel ATtiny24/44/84 has four sources of reset:
● Power-on reset. The MCU is reset when the supply voltage is below the power-on reset threshold (VPOT).
●
External reset. The MCU is reset when a low level is present on the RESET pin for longer than the minimum pulse
length when RESET function is enabled.
●
●
Watchdog reset. The MCU is reset when the watchdog timer period expires and the watchdog is enabled.
Brown-out reset. The MCU is reset when the supply voltage VCC is below the brown-out reset threshold (VBOT) and
the brown-out detector is enabled.
Figure 9-1. Reset Logic
DATA BUS
WDRF
BORF
EXTRF
PORF
MCU Status
Register (MCUSR)
Power-on Reset
Circuit
VCC
Pull-up Resistor
RESET
Spike
Filter
Reset Circuit
S
COUNTER RESET
R
Watchdog
Timer
Watchdog
Oscillator
Clock
Generator
CKSEL[1:0]
SUT[1:0]
36
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
CK
Delay Counters
TIMEOUT
Q
INTERNAL RESET
Brown-out
Reset Circuit
BODLEVEL [1..0]
9.3
Power-on Reset
A power-on reset (POR) pulse is generated by an on-chip detection circuit. The detection level is defined in Section 22.4
“System and Reset Characterizations” on page 158. The POR is activated whenever VCC is below the detection level. The
POR circuit can be used to trigger the start-up reset, as well as to detect a failure in supply voltage.
A POR circuit ensures that the device is reset from power-on. Reaching the power-on reset threshold voltage invokes the
delay counter, which determines how long the device is kept in RESET after VCC rise. The RESET signal is activated again,
without any delay, when VCC decreases below the detection level.
Figure 9-2. MCU Start-up, RESET Tied to VCC
VCCRR
VCC
VPORMAX
VPORMIN
RESET
VRST
tTOUT
Time-out
Internal
Reset
Figure 9-3. MCU Start-up, RESET Extended Externally
VCC
V POT
V RST
RESET
tTOUT
Time-out
Internal
Reset
Table 9-1.
Power On Reset Specifications
Parameter
Symbol
Power-on reset threshold voltage (rising)
(1)
Power-on reset threshold voltage (falling)
VPOT
Min
Typ
Max
Unit
1.1
1.4
1.7
V
0.8
1.3
1.6
V
0.4
V
VCC max. start voltage to ensure internal power-on reset
signal
VPORMAX
VCC Min. start voltage to ensure internal power-on reset
signal
VPORMIN
-0.1
V
VCCRR
0.01
V/ms
VCC rise rate to ensure power-on reset
RESET pin threshold voltage
VRST
0.1 VCC
Note:
1. Before rising, the supply has to be between VPORMIN and VPORMAX to ensure a reset.
0.9VCC
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
V
37
9.4
External Reset
An external reset is generated by a low level on the RESET pin if enabled. Reset pulses longer than the minimum pulse
width (see Section 22.4 “System and Reset Characterizations” on page 158) will generate a reset, even if the clock is not
running. Shorter pulses are not guaranteed to generate a reset. When the applied signal reaches the reset threshold voltage
– VRST – on its positive edge, the delay counter starts the MCU after the time-out period – tTOUT – has expired.
Figure 9-4. External Reset During Operation
VCC
V RST
RESET
tTOUT
Time-out
Internal
Reset
9.5
Brown-out Detection
Atmel® ATtiny24/44/84 has an on-chip brown-out detection (BOD) circuit for monitoring the VCC level during operation by
comparing it to a fixed trigger level. The trigger level for the BOD can be selected by the BODLEVEL fuses. The trigger level
has a hysteresis to ensure spike free brown-out detection. The hysteresis on the detection level should be interpreted as
VBOT+ = VBOT + VHYST/2 and VBOT– = VBOT – VHYST/2.
When the BOD is enabled, and VCC decreases to a value below the trigger level (VBOT– in Figure 9-5), the brown-out reset is
immediately activated. When VCC increases above the trigger level (VBOT+ in Figure 9-5), the delay counter starts the MCU
after the Time-out period tTOUT has expired.
The BOD circuit will only detect a drop in VCC if the voltage stays below the trigger level for longer than tBOD given in Section
22.4 “System and Reset Characterizations” on page 158.
Figure 9-5. Brown-out Reset During Operation
VCC
VBOT-
VBOT+
RESET
tTOUT
Time-out
Internal
Reset
38
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
9.6
Watchdog Reset
When the watchdog times out, it will generate a short reset pulse of one CK cycle duration. On the falling edge of this pulse,
the delay timer starts counting the time-out period tTOUT. See Section 9.8 “Watchdog Timer” on page 39 for details on
operation of the watchdog timer.
Figure 9-6. Watchdog Reset During Operation
VCC
RESET
1 CK Cycle
WDT
Time-out
RESET
Time-out
tTOUT
Internal
Reset
9.7
Internal Voltage Reference
The Atmel® ATtiny24/44/84 features an internal bandgap reference. This reference is used for brown-out detection, and it
can be used as an input to the analog comparator or the ADC.
9.7.1
Voltage Reference Enable Signals and Start-up Time
The voltage reference has a start-up time that may influence the way it should be used. The start-up time is given in Section
22.4 “System and Reset Characterizations” on page 158. To save power, the reference is not always turned on. The
reference is on during the following situations:
1. When the BOD is enabled (by programming the BODLEVEL [2..0] fuse).
2.
When the bandgap reference is connected to the analog comparator (by setting the ACBG bit in ACSR).
3.
When the ADC is enabled.
Thus, when the BOD is not enabled, after setting the ACBG bit or enabling the ADC, the user must always allow the
reference to start up before the output from the analog comparator or ADC is used. To reduce power consumption in
power-down mode, the user can avoid the three conditions above to ensure that the reference is turned off before entering
power-down mode.
9.8
Watchdog Timer
The watchdog timer is clocked from an on-chip oscillator which runs at 128kHz. By controlling the watchdog timer prescaler,
the watchdog reset interval can be adjusted as shown in Table 9-4 on page 43. The WDR – watchdog reset – instruction
resets the watchdog timer. The watchdog timer is also reset when it is disabled and when a chip reset occurs. Ten different
clock cycle periods can be selected to determine the reset period. If the reset period expires without another watchdog reset,
the Atmel ATtiny24/44/84 resets and executes from the reset vector. For timing details on the watchdog reset, refer to
Table 9-4 on page 43.
The watchdog timer can also be configured to generate an interrupt instead of a reset. This can be very helpful when using
the watchdog to wake-up from power-down.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
39
To prevent unintentional disabling of the watchdog or unintentional change of time-out period, two different safety levels are
selected by the WDTON fuse, as shown in Table 9-2 See Section 9.9 “Timed Sequences for Changing the Configuration of
the Watchdog Timer” on page 40 for details.
Table 9-2.
WDT Configuration as a Function of the Fuse Settings of WDTON
WDTON
Safety Level
WDT Initial State
How to Disable the WDT
How to Change Time-out
Unprogrammed
1
Disabled
Timed sequence
No limitations
Programmed
2
Enabled
Always enabled
Timed sequence
Figure 9-7. Watchdog Timer
128kHz
Oscillator
OSC/1024K
OSC/256K
OSC/512K
OSC/64K
OSC/128K
OSC/32K
OSC/8K
OSC/16K
OSC/4K
OSC/2K
Watchdog
Reset
Watchdog
Prescaler
WDP0
WDP1
WDP2
WDP3
WDE
MCU Reset
9.9
Timed Sequences for Changing the Configuration of the Watchdog Timer
The sequence for changing configuration differs slightly between the two safety levels. Separate procedures are described
for each level.
9.9.1
Safety Level 1
In this mode, the watchdog timer is initially disabled, but can be enabled by writing the WDE bit to logical one without any
restriction. A timed sequence is needed when disabling an enabled watchdog timer. To disable an enabled watchdog timer,
the following procedure must be followed:
1. In the same operation, write a logical one to WDCE and WDE. A logical one must be written to WDE regardless of
the previous value of the WDE bit.
2.
9.9.2
Within the next four clock cycles, in the same operation, write the WDE and WDP bits as desired, but with the
WDCE bit cleared.
Safety Level 2
In this mode, the watchdog timer is always enabled, and the WDE bit will always read as logical one. A timed sequence is
needed when changing the watchdog time-out period. To change the watchdog time-out, the following procedure must be
followed:
1. In the same operation, write a logical one to WDCE and WDE. Even though the WDE always is set, the WDE must
be written to one to start the timed sequence.
2.
40
Within the next four clock cycles, in the same operation, write the WDP bits as desired, but with the WDCE bit
cleared. The value written to the WDE bit is irrelevant.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
9.10
Register Description
9.10.1 MCUSR – MCU Status Register
The MCU status register provides information on which reset source caused an MCU reset.
Bit
7
6
5
4
3
2
1
0
0x34 (0x54)
–
–
–
–
WDRF
BORF
EXTRF
PORF
Read/Write
R
R
R
R
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
MCUSR
See Bit Description
• Bits 7..4 – Res: Reserved Bits
These bits are reserved bits in the Atmel® ATtiny24/44/84 and will always read as zero.
• Bit 3 – WDRF: Watchdog Reset Flag
This bit is set if a watchdog reset occurs. The bit is reset by a power-on reset, or by writing a logical zero to the flag.
• Bit 2 – BORF: Brown-out Reset Flag
This bit is set if a brown-out reset occurs. The bit is reset by a power-on reset, or by writing a logical zero to the flag.
• Bit 1 – EXTRF: External Reset Flag
This bit is set if an external reset occurs. The bit is reset by a power-on reset, or by writing a logical zero to the flag.
• Bit 0 – PORF: Power-on Reset Flag
This bit is set if a power-on reset occurs. The bit is reset only by writing a logic zero to the flag.
To make use of the reset flags to identify a reset condition, the user should read and then reset the MCUSR as early as
possible in the program. If the register is cleared before another reset occurs, the source of the reset can be found by
examining the reset flags.
9.10.2 WDTCSR – Watchdog Timer Control and Status Register
Bit
7
6
5
4
3
2
1
0
0x21 (0x41)
WDIF
WDIE
WDP3
WDCE
WDE
WDP2
WDP1
WDP0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
X
0
0
0
WDTCSR
• Bit 7 – WDIF: Watchdog Time-out Interrupt Flag
This bit is set when a time-out occurs in the watchdog timer and the watchdog timer is configured for interrupt. WDIF is
cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, WDIF is cleared by writing a
logic one to the flag. When the I-bit in SREG and WDIE are set, the watchdog time-out interrupt is executed.
• Bit 6 – WDIE: Watchdog Timeout Interrupt Enable
When this bit is written to logical one, WDE is cleared, and the I-bit in the status register is set, the watchdog time-out
interrupt is enabled. In this mode the corresponding interrupt is executed instead of a reset if a time-out in the watchdog
timer occurs.
If WDE is set, WDIE is automatically cleared by hardware when a time-out occurs. This is useful for keeping the watchdog
reset security while using the interrupt. After the WDIE bit is cleared, the next time-out will generate a reset. To avoid the
watchdog reset, WDIE must be set after each interrupt.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
41
Table 9-3.
Watchdog Timer Configuration
WDE
WDIE
Watchdog Timer State
Action on Time-out
0
0
Stopped
None
0
1
Running
Interrupt
1
0
Running
Reset
1
1
Running
Interrupt
• Bit 4 – WDCE: Watchdog Change Enable
This bit must be set when the WDE bit is written to logical zero. Otherwise, the watchdog will not be disabled. Once written to
logical one, hardware will clear this bit after four clock cycles. See the description of the WDE bit for a watchdog disable
procedure. This bit must also be set when changing the prescaler bits. See Section 9.9 “Timed Sequences for Changing the
Configuration of the Watchdog Timer” on page 40.
• Bit 3 – WDE: Watchdog Enable
When the WDE is written to logical one, the watchdog timer is enabled, and if the WDE is written to logical zero, the
watchdog timer function is disabled. WDE can only be cleared if the WDCE bit has logic level one. To disable an enabled
watchdog timer, the following procedure must be followed:
1. In the same operation, write a logical one to WDCE and WDE. A logical one must be written to WDE even though
it is set to logical one before the disable operation starts.
2.
Within the next four clock cycles, write a logical zero to WDE. This disables the watchdog.
In safety level 2, it is not possible to disable the watchdog timer, even with the algorithm described above. See Section 9.9
“Timed Sequences for Changing the Configuration of the Watchdog Timer” on page 40.
In safety level 1, WDE is overridden by WDRF in MCUSR. See Section 9.10.1 “MCUSR – MCU Status Register” on page 41
for description of WDRF. This means that WDE is always set when WDRF is set. To clear WDE, WDRF must be cleared
before disabling the Watchdog with the procedure described above. This feature ensures multiple resets during conditions
causing failure, and a safe start-up after the failure.
Note:
If the watchdog timer is not going to be used in the application, it is important to go through a watchdog disable
procedure in the initialization of the device. If the watchdog is accidentally enabled, for example by a runaway
pointer or brown-out condition, the device will be reset, which in turn will lead to a new watchdog reset. To
avoid this situation, the application software should always clear the WDRF flag and the WDE control bit in the
initialization routine.
• Bits 5, 2..0 – WDP3..0: Watchdog Timer Prescaler 3, 2, 1, and 0
The WDP3..0 bits determine the watchdog timer prescaling when the watchdog timer is enabled. The different prescaling
values and their corresponding time-out periods are shown in Table 9-4 on page 43.
42
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 9-4.
Watchdog Timer Prescale Select
WDP3
WDP2
WDP1
WDP0
Number of WDT Oscillator Cycles
Typical Time-out at
VCC = 5.0V
0
0
0
0
2Kcycles
16ms
0
0
0
1
4Kcycles
32ms
0
0
1
0
8Kcycles
64ms
0
0
1
1
16Kcycles
0.125s
0
1
0
0
32Kcycles
0.25s
0
1
0
1
64Kcycles
0.5s
0
1
1
0
128Kcycles
1.0s
0
1
1
1
256Kcycles
2.0s
1
0
0
0
512Kcycles
4.0s
1
0
0
1
1024Kcycles
8.0s
1
0
1
0
1
0
1
1
1
1
0
0
1
1
0
1
1
1
1
0
1
1
1
1
Reserved
The following code example shows one assembly function and one C function for turning off the WDT. The example
assumes that interrupts are controlled (e.g., by disabling interrupts globally) so that no interrupts will occur during execution
of these functions.
Assembly Code Example(1)
WDT_off:
WDR
; Clear WDRF in MCUSR
ldi
r16, (0<<WDRF)
out
MCUSR, r16
; Write logical one to WDCE and WDE
; Keep old prescaler setting to prevent unintentional Watchdog
Reset
in
r16, WDTCR
ori
r16, (1<<WDCE)|(1<<WDE)
out
WDTCR, r16
; Turn off WDT
ldi
r16, (0<<WDE)
out
WDTCR, r16
ret
C Code Example(1)
void WDT_off(void)
{
_WDR();
/* Clear WDRF in MCUSR */
MCUSR = 0x00
/* Write logical one to WDCE and WDE */
WDTCR |= (1<<WDCE) | (1<<WDE);
/* Turn off WDT */
WDTCR = 0x00;
}
Note:
1.
See Section 4. “About Code Examples” on page 8.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
43
10.
Interrupts
This section describes the specifics of the interrupt handling as performed in Atmel® ATtiny24/44/84. For a general
explanation of the AVR® interrupt handling, see Section 5.8 “Reset and Interrupt Handling” on page 14.
10.1
Interrupt Vectors
Table 10-1. Reset and Interrupt Vectors
44
Vector No.
Program Address
Source
Interrupt Definition
1
0x0000
RESET
External pin, power-on reset, brown-out reset,
watchdog reset
2
0x0001
INT0
External interrupt request 0
3
0x0002
PCINT0
Pin change interrupt request 0
4
0x0003
PCINT1
Pin change interrupt request 1
5
0x0004
WDT
Watchdog time-out
6
0x0005
TIMER1 CAPT
Timer/Counter1 capture event
7
0x0006
TIMER1 COMPA
Timer/Counter1 compare match A
8
0x0007
TIMER1 COMPB
Timer/Counter1 compare match B
9
0x0008
TIMER1 OVF
Timer/Counter0 overflow
10
0x0009
TIMER0 COMPA
Timer/Counter0 compare match A
11
0x000A
TIMER0 COMPB
Timer/Counter0 compare match B
12
0x000B
TIMER0 OVF
Timer/Counter0 overflow
13
0x000C
ANA_COMP
Analog comparator
14
0x000D
ADC
ADC conversion complete
15
0x000E
EE_RDY
EEPROM ready
16
0x000F
USI_START
USI START
17
0x0010
USI_OVF
USI overflow
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
If the program never enables an interrupt source, the interrupt vectors are not used, and regular program code can be placed
at these locations. The most typical and general program setup for the reset and interrupt vector Addresses in Atmel®
ATtiny24/44/84 is:
Address
Labels Code
Comments
0x0000
rjmp
RESET
; Reset Handler
0x0001
rjmp
EXT_INT0
; IRQ0 Handler
0x0002
rjmp
PCINT0
; PCINT0 Handler
0x0003
rjmp
PCINT1
; PCINT1 Handler
0x0004
rjmp
WATCHDOG
; Watchdog Interrupt Handler
0x0005
rjmp
TIM1_CAPT
; Timer1 Capture Handler
0x0006
rjmp
TIM1_COMPA
; Timer1 Compare A Handler
0x0007
rjmp
TIM1_COMPB
; Timer1 Compare B Handler
0x0008
rjmp
TIM1_OVF
; Timer1 Overflow Handler
0x0009
rjmp
TIM0_COMPA
; Timer0 Compare A Handler
0x000A
rjmp
TIM0_COMPB
; Timer0 Compare B Handler
0x000B
rjmp
TIM0_OVF
; Timer0 Overflow Handler
0x000C
rjmp
ANA_COMP
; Analog Comparator Handler
0x000D
rjmp
ADC
; ADC Conversion Handler
0x000E
rjmp
EE_RDY
; EEPROM Ready Handler
0x000F
rjmp
USI_STR
; USI STart Handler
0x0010
rjmp
USI_OVF
; USI Overflow Handler
;
0x0011
RESET: ldi
r16, high(RAMEND); Main program start
0x0012
out
SPH,r16
; Set Stack Pointer to top of RAM
0x0013
ldi
r16, low(RAMEND)
0x0014
out
SPL,r16
0x0015
sei
; Enable interrupts
0x0016
<instr> xxx
...
...
...
...
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
45
11.
External Interrupts
The external interrupts are triggered by the INT0 pin or any of the PCINT11..0 pins. Observe that, if enabled, the interrupts
will trigger even if the INT0 or PCINT11..0 pins are configured as outputs. This feature provides a way of generating a
software interrupt. Pin change 0 interrupts (PCI0) will trigger if any enabled PCINT7..0 pin toggles. Pin change 1 interrupts
(PCI1) will trigger if any enabled PCINT11..8 pin toggles. The PCMSK0 and PCMSK1 registers control which pins contribute
to the pin change interrupts. Pin change interrupts on PCINT11..0 are detected asynchronously. This implies that these
interrupts also can be used for waking the part from sleep modes other than idle mode.
The INT0 interrupts can be triggered by a falling or rising edge or a low level. This is set up as indicated in the specification
for the MCU control register (MCUCR). When the INT0 interrupt is enabled and is configured as level-triggered, the interrupt
will trigger as long as the pin is held low. Note that recognition of falling- or rising-edge interrupts on INT0 requires the
presence of an I/O clock, described in Section 7.1 “Clock Systems and their Distribution” on page 24. Low level interrupt on
INT0 is detected asynchronously. This implies that this interrupt also can be used for waking the part from sleep modes other
than idle mode. The I/O clock is halted in all sleep modes except idle mode.
Note that if a level-triggered interrupt is used for wake-up from power-down, the required level must be held long enough for
the MCU to complete the wake-up to trigger the level interrupt. If the level disappears before the end of the start-up time, the
MCU will still wake up, but no interrupt will be generated. The start-up time is defined by the SUT and CKSEL fuses as
described in Section 7. “System Clock and Clock Options” on page 24.
11.1
Pin Change Interrupt Timing
An example of timing of a pin change interrupt is shown in Figure 11-1.
Figure 11-1. Timing of Pin Change Interrupts
pin_lat
PCINT(0)
D
Q
pcint_in_(0) 0
pin_sync
pcint_sync
pcint_setflag
PCIF
LE
x
PCINT(0) in PCMSK(x)
clk
clk
clk
PCINT(0)
pin_lat
pin_sync
pcint_in_(0)
pcint_syn
pcint_setflag
PCIF
46
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
11.2
Register Description
11.2.1 MCUCR – MCU Control Register
The external interrupt control register A contains control bits for interrupt sense control.
Bit
7
6
5
4
3
2
1
0
0x35 (0x55)
BODS
Read/Write
R/W
PUD
SE
SM1
SM0
BODSE
ISC01
ISC00
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
MCUCR
• Bits 1, 0 – ISC01, ISC00: Interrupt Sense Control 0 Bit 1 and Bit 0
The external interrupt 0 is activated by the external pin INT0 if the SREG I-flag and the corresponding interrupt mask are set.
The level and edges on the external INT0 pin that activate the interrupt are defined in Table 11-1. The value on the INT0 pin
is sampled before detecting edges. If edge or toggle interrupt is selected, pulses that last longer than one clock period will
generate an interrupt. Shorter pulses are not guaranteed to generate an interrupt. If low level interrupt is selected, the low
level must be held until the completion of the currently executing instruction to generate an interrupt.
Table 11-1. Interrupt 0 Sense Control
ISC01
ISC00
Description
0
0
The low level of INT0 generates an interrupt request.
0
1
Any logical change on INT0 generates an interrupt request.
1
0
The falling edge of INT0 generates an interrupt request.
1
1
The rising edge of INT0 generates an interrupt request.
11.2.2 GIMSK – General Interrupt Mask Register
Bit
7
6
5
4
3
2
1
0
0x3B (0x5B)
–
INT0
PCIE1
PCIE0
–
–
–
–
Read/Write
R
R/W
R/W
R/w
R
R
R
R
Initial Value
0
0
0
0
0
0
0
0
GIMSK
• Bits 7, 3..0 – Res: Reserved Bits
These bits are reserved bits in the Atmel® ATtiny24/44/84 and will always read as zero.
• Bit 6 – INT0: External Interrupt Request 0 Enable
When the INT0 bit is set (one) and the I-bit in the status register (SREG) is set (one), the external pin interrupt is enabled.
The interrupt sense control0 bits 1/0 (ISC01 and ISC00) in the external interrupt control register A (EICRA) define whether
the external interrupt is activated on rising and/or falling edge of the INT0 pin or level sensed. Activity on the pin will cause an
interrupt request even if INT0 is configured as an output. The corresponding interrupt of external interrupt request 0 is
executed from the INT0 interrupt vector.
• Bit 5 – PCIE1: Pin Change Interrupt Enable 1
When the PCIE1 bit is set (one) and the I-bit in the status register (SREG) is set (one), pin change interrupt 1 is enabled. Any
change on any enabled PCINT11..8 pin will cause an interrupt. The corresponding interrupt of pin change interrupt request is
executed from the PCI1 interrupt vector. PCINT11..8 pins are enabled individually by the PCMSK1 register.
• Bit 4– PCIE0: Pin Change Interrupt Enable 0
When the PCIE0 bit is set and the I-bit in the status register (SREG) is set, pin change interrupt 0 is enabled. Any change on
any enabled PCINT7..0 pin will cause an interrupt. The corresponding interrupt of pin change interrupt request is executed
from the PCI0 interrupt vector. PCINT7..0 pins are enabled individually by the PCMSK0 register.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
47
11.2.3 GIFR – General Interrupt Flag Register
Bit
7
6
5
4
3
2
1
0x3A (0x5A
–
INTF0
PCIF1
PCIF0
–
–
–
0
–
Read/Write
R
R/W
R/W
R/W
R
R
R
R
Initial Value
0
0
0
0
0
0
0
0
GIFR
• Bits 7, 3..0 – Res: Reserved Bits
These bits are reserved bits in the Atmel® ATtiny24/44/84 and will always read as zero.
• Bit 6 – INTF0: External Interrupt Flag 0
When an edge or logic change on the INT0 pin triggers an interrupt request, INTF0 becomes set (logical one). If the I-bit in
SREG and the INT0 bit in GIMSK are set (one), the MCU will jump to the corresponding interrupt vector. The flag is cleared
when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it. This flag is always
cleared when INT0 is configured as a level interrupt.
• Bit 5 – PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT11..8 pin triggers an interrupt request, PCIF1 becomes set (logical one). If the I-bit in
SREG and the PCIE1 bit in GIMSK are set (one), the MCU will jump to the corresponding interrupt vector. The flag is cleared
when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it.
• Bit 4– PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7..0 pin triggers an interrupt request, PCIF becomes set (logical one). If the I-bit in SREG
and the PCIE0 bit in GIMSK are set (one), the MCU will jump to the corresponding interrupt vector. The flag is cleared when
the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical one to it.
11.2.4 PCMSK1 – Pin Change Mask Register 1
Bit
7
6
5
4
3
2
1
0
0x20 (0x40)
–
–
–
–
PCINT11
PCINT10
PCINT9
PCINT8
Read/Write
R
R
R
R
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
PCMSK1
• Bits 7, 4– Res: Reserved Bits
These bits are reserved bits in the Atmel ATtiny24/44/84 and will always read as zero.
• Bits 3..0 – PCINT11..8: Pin Change Enable Mask 11..8
Each PCINT11..8 bit selects whether pin change interrupt is enabled on the corresponding I/O pin. If PCINT11..8 is set
(logical one) and the PCIE1 bit in GIMSK is set, pin change interrupt is enabled on the corresponding I/O pin. If PCINT11..8
is cleared, pin change interrupt on the corresponding I/O pin is disabled.
11.2.5 PCMSK0 – Pin Change Mask Register 0
Bit
7
6
5
4
3
2
1
0
0x12 (0x32)
PCINT7
PCINT6
PCINT5
PCINT4
PCINT3
PCINT2
PCINT1
PCINT0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
PCMSK0
• Bits 7..0 – PCINT7..0: Pin Change Enable Mask 7..0
Each PCINT7..0 bit selects whether pin change interrupt is enabled on the corresponding I/O pin. If PCINT7..0 is set (logical
one) and the PCIE0 bit in GIMSK is set, pin change interrupt is enabled on the corresponding I/O pin. If PCINT7..0 is
cleared, pin change interrupt on the corresponding I/O pin is disabled.
48
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
12.
I/O Ports
12.1
Overview
All Atmel® AVR® ports have true read-modify-write functionality when used as general digital I/O ports. This means that the
SBI and CBI instructions can be used to change direction of one port pin without unintentionally changing the direction of any
other pin. The same applies when changing drive value (if configured as output) or enabling/disabling of pull-up resistors (if
configured as input). Each output buffer has symmetrical drive characteristics with both high sink and source capability. The
pin driver is strong enough to drive LED displays directly. All port pins have individually selectable pull-up resistors with a
supply-voltage invariant resistance. All I/O pins have protection diodes to both VCC and ground as indicated in Figure 12-1.
See Section 22. “Electrical Characteristics” on page 155 for a complete list of parameters.
Figure 12-1. I/O Pin Equivalent Schematic
Rpu
Pxn
Logic
Cpin
See Figure
”General Digital I/O”
for Details
All registers and bit references in this section are written in general form. A lower case “x” represents the numbering letter for
the port, and a lower case “n” represents the bit number. However, when using the register or bit defines in a program, the
precise form must be used. For example, PORTB3 for bit no. 3 in Port B, here documented generally as PORTxn. The
physical I/O registers and bit locations are listed in “EXT_CLOCK = external clock is selected as system clock.” on page 61.
Three I/O memory address locations are allocated for each port, one each for the data register (PORTx), data direction
register (DDRx), and the port input pins (PINx). The port input pins I/O location is read only, while the data register and the
data direction register are read/write. However, writing a logical one to a bit in the PINx register, will result in a toggle in the
corresponding bit in the data register. In addition, the pull-up disable (PUD) bit in the MCUCR disables the pull-up function
for all pins in all ports when set.
Using the I/O port as general digital I/O is described in Section 12.2 “Ports as General Digital I/O” on page 50. Most port pins
are multiplexed with alternate functions for the peripheral features on the device. How each alternate function interferes with
the port pin is described in Section 12.3 “Alternate Port Functions” on page 54. Refer to the individual module sections for a
full description of the alternate functions.
Note that enabling the alternate function of some of the port pins does not affect the use of the other pins in the port as
general digital I/O.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
49
12.2
Ports as General Digital I/O
The ports are bi-directional I/O ports with optional internal pull-ups. Figure 12-2 shows a functional description of one
I/O-port pin, here generically called Pxn.
Figure 12-2. General Digital I/O(1)
PUD
Q
D
DDxn
Q
CLR
RESET
WDx
RDx
0
PORTxn
Q
CLR
RESET
SLEEP
DATA BUS
1
D
Q
Pxn
WRx
WPx
RRx
Synchronizer
RPx
D
Q
D
Q
PINxn
L
Q
Q
CLKI/O
PUD:
SLEEP:
CLKI/O:
Note:
1.
PULLUP DISABLE
SLEEP CONTROL
I/O CLOCK
WDx:
RDx:
WRx:
RRx:
RPx:
WPx:
WRITE DDRx
READ DDRx
WRITE PORTx
READ PORTx REGISTER
READ PORTx PIN
WRITE PINx REGISTER
WRx, WPx, WDx, RRx, RPx, and RDx are common to all pins within the same port. clkI/O, SLEEP, and PUD
are common to all ports.
12.2.1 Configuring the Pin
Each port pin consists of three register bits: DDxn, PORTxn, and PINxn. As shown in “EXT_CLOCK = external clock is
selected as system clock.” on page 61, the DDxn bits are accessed at the DDRx I/O address, the PORTxn bits at the PORTx
I/O address, and the PINxn bits at the PINx I/O address.
The DDxn bit in the DDRx register selects the direction of this pin. If DDxn is written logical one, Pxn is configured as an
output pin. If DDxn is written logical zero, Pxn is configured as an input pin.
If PORTxn is written logical one when the pin is configured as an input pin, the pull-up resistor is activated. To switch the
pull-up resistor off, PORTxn has to be written logical zero or the pin has to be configured as an output pin. The port pins are
tri-stated when reset condition becomes active, even if no clocks are running.
If PORTxn is written logical one when the pin is configured as an output pin, the port pin is driven high (one). If PORTxn is
written logical zero when the pin is configured as an output pin, the port pin is driven low (zero).
50
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
12.2.2 Toggling the Pin
Writing a logical one to PINxn toggles the value of PORTxn, independent on the value of DDRxn. Note that the SBI
instruction can be used to toggle one single bit in a port.
12.2.3 Switching Between Input and Output
When switching between tri-state ({DDxn, PORTxn} = 0b00) and output high ({DDxn, PORTxn} = 0b11), an intermediate
state with either pull-up enabled ({DDxn, PORTxn} = 0b01) or output low ({DDxn, PORTxn} = 0b10) must occur. Normally,
the pull-up enabled state is fully acceptable, as a high-impedance environment will not notice the difference between a
strong high driver and a pull-up. If this is not the case, the PUD bit in the MCUCR register can be set to disable all pull-ups in
all ports.
Switching between input with pull-up and output low generates the same problem. The user must use either the tri-state
({DDxn, PORTxn} = 0b00) or the output high state ({DDxn, PORTxn} = 0b10) as an intermediate step.
Table 12-1 summarizes the control signals for the pin value.
Table 12-1. Port Pin Configurations
DDxn
PORTxn
PUD
(in MCUCR)
I/O
Pull-up
0
0
X
Input
No
Tri-state (Hi-Z)
0
1
0
Input
Yes
Pxn will source current if ext. pulled low.
0
1
1
Input
No
Tri-state (Hi-Z)
1
0
X
Output
No
Output low (sink)
1
1
X
Output
No
Output high (source)
Comment
12.2.4 Reading the Pin Value
Independent of the setting of data direction bit DDxn, the port pin can be read through the PINxn register bit. As shown in
Figure 12-2 on page 50, the PINxn register bit and the preceding latch constitute a synchronizer. This is needed to avoid
metastability if the physical pin changes value near the edge of the internal clock, but it also introduces a delay. Figure 12-3
shows a timing diagram of the synchronization when reading an externally applied pin value. The maximum and minimum
propagation delays are denoted tpd,max and tpd,min respectively.
Figure 12-3. Synchronization when Reading an Externally Applied Pin Value
System CLK
Instructions
XXX
XXX
in r17, PINx
SYNC Latch
PINxn
r17
0x00
0xFF
tpd, max
tpd, min
Consider the clock period starting shortly after the first falling edge of the system clock. The latch is closed when the clock is
low, and goes transparent when the clock is high, as indicated by the shaded region of the “SYNC LATCH” signal. The signal
value is latched when the system clock goes low. It is clocked into the PINxn register at the succeeding positive clock edge.
As indicated by the two arrows tpd,max and tpd,min, a single signal transition on the pin will be delayed between ½ and 1½
system clock period depending upon the time of assertion.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
51
When reading back a software assigned pin value, a nop instruction must be inserted as indicated in Figure 12-4. The out
instruction sets the “SYNC LATCH” signal at the positive edge of the clock. In this case, the delay tpd through the
synchronizer is one system clock period.
Figure 12-4. Synchronization when Reading a Software Assigned Pin Value
System CLK
r16
Instructions
0xFF
out PORTx, r16
nop
in r17, PINx
SYNC Latch
PINxn
r17
0x00
0xFF
tpd
The following code example shows how to set port A pins 0 and 1 high, 2 and 3 low, and define the port pins from 4 to 5 as
input with a pull-up assigned to port pin 4. The resulting pin values are read back again, but as previously discussed, a nop
instruction is included to be able to read back the value recently assigned to some of the pins.
Assembly Code Example(1)
...
; Define pull-ups and set outputs high
; Define directions for port pins
ldi
r16,(1<<PA4)|(1<<PA1)|(1<<PA0)
ldi
r17,(1<<DDA3)|(1<<DDA2)|(1<<DDA1)|(1<<DDA0)
out
PORTA,r16
out
DDRA,r17
; Insert nop for synchronization
nop
; Read port pins
in
r16,PINA
...
C Code Example
unsigned char i;
...
/* Define pull-ups and set outputs high */
/* Define directions for port pins */
PORTA = (1<<PA4)|(1<<PA1)|(1<<PA0);
DDRA = (1<<DDA3)|(1<<DDA2)|(1<<DDA1)|(1<<DDA0);
/* Insert nop for synchronization*/
_NOP();
/* Read port pins */
i = PINA;
...
Note:
52
1.
For the assembly program, two temporary registers are used to minimize the time from pull-ups are set on pins
0, 1 and 4, until the direction bits are correctly set, defining bit 2 and 3 as low and redefining bits 0 and 1 as
strong high drivers.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
12.2.5 Digital Input Enable and Sleep Modes
As shown in Figure 12-2 on page 50, the digital input signal can be clamped to ground at the input of the schmitt-trigger. The
signal denoted SLEEP in the figure, is set by the MCU sleep controller in power-down mode, power-save mode, and standby
mode to avoid high power consumption if some input signals are left floating, or have an analog signal level close to VCC/2.
SLEEP is overridden for port pins enabled as external interrupt pins. If the external interrupt request is not enabled, SLEEP
is active also for these pins. SLEEP is also overridden by various other alternate functions as described in Section 12.3
“Alternate Port Functions” on page 54.
If a logic high level (logical one) is present on an asynchronous external interrupt pin configured as “interrupt on rising edge,
falling edge, or any logic change on pin” while the external interrupt is not enabled, the corresponding external interrupt flag
will be set when resuming from the above mentioned sleep mode, as the clamping in these sleep mode produces the
requested logic change.
12.2.6 Unconnected Pins
If some pins are unused, it is recommended to ensure that these pins have a defined level. Even though most of the digital
inputs are disabled in the deep sleep modes as described above, floating inputs should be avoided to reduce current
consumption in all other modes where the digital inputs are enabled (reset, active mode and idle mode).
The simplest method to ensure a defined level of an unused pin is to enable the internal pull-up. In this case, the pull-up will
be disabled during reset. If low power consumption during reset is important, it is recommended to use an external pull-up or
pull-down. Connecting unused pins directly to VCC or GND is not recommended, since this may cause excessive currents if
the pin is accidentally configured as an output.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
53
12.3
Alternate Port Functions
Most port pins have alternate functions in addition to being general digital I/Os. Figure 12-5 shows how the port pin control
signals from the simplified Figure 12-2 on page 50 can be overridden by alternate functions. The overriding signals may not
be present in all port pins, but the figure serves as a generic description applicable to all port pins in the Atmel® AVR®
microcontroller family.
Figure 12-5. Alternate Port Functions(1)
PUOExn
1
PUOVxn
PUD
0
DDOExn
1
DDOVxn
0
Q
D
DDxn
Q
CLR
RESET
WDx
RDx
PVOExn
1
PVOVxn
1
D
Q
0
0
PORTxn
Q
DIEOExn
1
DIEOVxn
0
SLEEP
DATA BUS
Pxn
PTOExn
CLR
RESET
WRx
WPx
RRx
Synchronizer
RPx
D SET Q
D
Q
PINxn
L
CLR
Q
CLR
Q
CLKI/O
DIxn
AIOxn
PUOExn:
PUOVxn:
DDOExn:
DDOVxn:
PVOExn:
PVOVxn:
DIEOExn:
DIEOVxn:
SLEEP:
PTOExn:
Note:
54
1.
Pxn PULL-UP OVERRIDE ENABLE
Pxn PULL-UP OVERRIDE VALUE
Pxn DATA DIRECTION OVERRIDE ENABLE
Pxn DATA DIRECTION OVERRIDE VALUE
Pxn PORT VALUE OVERRIDE ENABLE
Pxn PORT VALUE OVERRIDE VALUE
Pxn DIGITAL INPUT ENABLE OVERRIDE ENABLE
Pxn DIGITAL INPUT ENABLE OVERRIDE VALUE
SLEEP CONTROL
Pxn, PORT TOGGLE OVERRIDE ENABLE
PUD:
WDx:
RDx:
RRx:
WRx:
RPx:
WPx:
CLK:I/O
DIxn:
AIOxn:
PULL-UP DISABLE
WRITE DDRx
READ DDRx
READ PORTx REGISTER
WRITE PORTx
READ PORTx PIN
WRITE PINx
I/O CLOCK
DIGITAL INPUT PIN n ON PORTx
ANALOG INPUT/OUTPUT PIN n ON PORTx
WRx, WPx, WDx, RRx, RPx, and RDx are common to all pins within the same port. clkI/O, SLEEP, and PUD
are common to all ports. All other signals are unique for each pin.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 12-2 summarizes the function of the overriding signals. The pin and port indexes from Figure 12-5 on page 54 are not
shown in the succeeding tables. The overriding signals are generated internally in the modules having the alternate function.
Table 12-2. Generic Description of Overriding Signals for Alternate Functions
Signal Name
Full Name
Description
PUOE
Pull-up override enable
If this signal is set, the pull-up enable is controlled by the PUOV signal. If
this signal is cleared, the pull-up is enabled when {DDxn, PORTxn,
PUD} = 0b010.
PUOV
Pull-up override value
If PUOE is set, the pull-up is enabled/disabled when PUOV is set/cleared,
regardless of the setting of the DDxn, PORTxn, and PUD register bits.
DDOE
Data direction override
enable
If this signal is set, the output driver enable is controlled by the DDOV
signal. If this signal is cleared, the output driver is enabled by the DDxn
register bit.
DDOV
Data direction override
value
If DDOE is set, the output driver is enabled/disabled when DDOV is
set/cleared, regardless of the setting of the DDxn register bit.
PVOE
Port value override
enable
If this signal is set and the output driver is enabled, the port value is
controlled by the PVOV signal. If PVOE is cleared, and the output driver is
enabled, the port value is controlled by the PORTxn register bit.
PVOV
Port value override value
If PVOE is set, the port value is set to PVOV, regardless of the setting of the
PORTxn register bit.
PTOE
Port toggle override
enable
If PTOE is set, the PORTxn register bit is inverted.
DIEOE
Digital input enable
override enable
If this bit is set, the digital input enable is controlled by the DIEOV signal. If
this signal is cleared, the digital input enable is determined by MCU state
(normal mode, sleep mode).
DIEOV
Digital input enable
override value
If DIEOE is set, the digital input is enabled/disabled when DIEOV is
set/cleared, regardless of the MCU state (normal mode, sleep mode).
DI
Digital input
This is the digital input to alternate functions. In the figure, the signal is
connected to the output of the schmitt-trigger but before the synchronizer.
Unless the digital input is used as a clock source, the module with the
alternate function will use its own synchronizer.
AIO
Analog input/output
This is the analog input/output to/from alternate functions. The signal is
connected directly to the pad, and can be used bi-directionally.
The following subsections shortly describe the alternate functions for each port, and relate the overriding signals to the
alternate function. Refer to the alternate function description for further details.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
55
12.3.1 Alternate Functions of Port A
The port A pins with alternate function are shown in Table 12-7 on page 59.
Table 12-3. Port A Pins Alternate Functions
Port Pin
Alternate Function
ADC0: ADC input channel 0.
PA0
AREF: External analog reference.
PCINT0: Pin change interrupt 0 source 0.
PA1
PA2
PA3
PA4
PA5
PA6
PA7
ADC1:
ADC input channel 1.
AIN0:
Analog comparator positive input.
PCINT1:
Pin change interrupt 0 source 1.
ADC2:
ADC input channel 2.
AIN1:
Analog comparator negative input.
PCINT2:
Pin change interrupt 0 source 2.
ADC3:
ADC input channel 3.
T0:
Timer/Counter0 counter source.
PCINT3:
Pin change interrupt 0 source 3.
ADC4:
ADC input channel 4.
USCK:
USI Clock three wire mode.
SCL:
USI Clock two wire mode.
T1:
Timer/Counter1 counter source.
PCINT4:
Pin change interrupt 0 source 4.
ADC5:
ADC input channel 5.
DO:
USI data output three wire mode.
OC1B:
Timer/Counter1 compare match B output.
PCINT5:
Pin change interrupt 0 source 5.
ADC6:
ADC input channel 6.
DI:
USI data input three wire mode.
SDA:
USI data input two wire mode.
OC1A:
Timer/Counter1 compare match A output.
PCINT6:
Pin change interrupt 0 source 6.
ADC7:
ADC input channel 7.
OC0B:
Timer/Counter0 compare match B output.
ICP1:
Timer/Counter1 input capture pin.
PCINT7:
Pin change interrupt 0 source 7.
• Port A, Bit 0 – ADC0/AREF/PCINT0
ADC0: Analog to digital converter, channel 0.
AREF: External analog reference for ADC. Pull up and output driver are disabled on PA0 when the pin is used as an external
reference or internal voltage reference with external capacitor at the AREF pin by setting (one) the bit REFS0 in the ADC
multiplexer selection register (ADMUX).
PCINT0: Pin change interrupt source 0. The PA0 pin can serve as an external interrupt source for pin change interrupt 0.
56
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
• Port A, Bit 1 – ADC1/AIN0/PCINT1
ADC1: Analog to digital converter, channel 1.
AIN0: Analog comparator positive input. Configure the port pin as input with the internal pull-up switched off to avoid the
digital port function from interfering with the function of the analog comparator.
PCINT1: Pin change interrupt source 1. The PA1 pin can serve as an external interrupt source for pin change interrupt 0.
• Port A, Bit 2 – ADC2/AIN1/PCINT2
ADC2: Analog to digital converter, channel 2.
AIN1: Analog comparator negative input. Configure the port pin as input with the internal pull-up switched off to avoid the
digital port function from interfering with the function of the analog comparator.
PCINT2: Pin change interrupt source 2. The PA2 pin can serve as an external interrupt source for pin change interrupt 0.
• Port A, Bit 3 – ADC3/T0/PCINT3
ADC3: Analog to digital converter, channel 3.
T0: Timer/Counter 0 counter source.
PCINT3: Pin change interrupt source 3. The PA3 pin can serve as an external interrupt source for pin change interrupt 0.
• Port A, Bit 4 – ADC4/USCK/SCL/T1/PCINT4
ADC4: Analog to digital converter, channel 4.
USCK: Three-wire mode universal serial interface clock.
SCL: Two-wire mode serial clock for USI two-wire mode.
T1: Timer/Counter1 counter source.
PCINT4: Pin change interrupt source 4. The PA4 pin can serve as an external interrupt source for pin change interrupt 0.
• Port A, Bit 5 – ADC5/DO/OC1B/PCINT5
ADC5: Analog to digital converter, channel 5.
DO: Data output in USI three-wire mode. Data output (DO) overrides PORTA5 value, and it is driven to the port when the
data direction bit DDA5 is set (one). However the PORTA5 bit still controls the pull-up, enabling pull-up if direction is input
and PORTA5 is set (one).
OC1B: Output compare match output: The PA5 pin can serve as an external output for the Timer/Counter1 compare match
B. The PA5 pin has to be configured as an output (DDA5 set (one)) to serve this function. The OC1B pin is also the output
pin for the PWM mode timer function.
PCINT5: Pin change interrupt source 5. The PA5 pin can serve as an external interrupt source for pin change interrupt 0.
• Port A, Bit 6 – ADC6/DI/SDA/OC1A/PCINT6
ADC6: Analog to digital converter, channel 6.
SDA: Two-wire mode serial interface data.
DI: Data input in USI three-wire mode. USI three-wire mode does not override normal port functions, so pin must be
configure as an input for DI function.
OC1A: Output compare match output: The PA6 pin can serve as an external output for the Timer/Counter1 compare match
A. The PA6 pin has to be configured as an output (DDA6 set (one)) to serve this function. The OC1A pin is also the output
pin for the PWM mode timer function.
PCINT6: Pin change interrupt source 6. The PA6 pin can serve as an external interrupt source for pin change interrupt 0.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
57
• Port A, Bit 7 – ADC7/OC0B/ICP1/PCINT7
ADC7: Analog to digital converter, channel 7.
OC1B: Output compare match output: The PA7 pin can serve as an external output for the Timer/Counter1 compare match
B. The PA7 pin has to be configured as an output (DDA7 set (one)) to serve this function. The OC1B pin is also the output
pin for the PWM mode timer function.
ICP1: Input capture pin: The PA7 pin can act as an input capture pin for Timer/Counter1.
PCINT7: Pin change interrupt source 7. The PA7 pin can serve as an external interrupt source for pin change interrupt 0.
Table 12-4 to Table 12-6 on page 59 relate the alternate functions of Port A to the overriding signals shown in Figure 12-5 on
page 54.
Table 12-4. Overriding Signals for Alternate Functions in PA7..PA5
Signal Name PA7/ADC7/OC0B/ICP1/ PCINT7
PA6/ADC6/DI/SDA/OC1A/ PCINT6 PA5/ADC5/DO/OC1B/ PCINT5
PUOE
0
0
0
PUOV
0
0
0
DDOE
0
USIWM1
0
DDOV
0
(SDA + PORTA6)  DDRA6
0
PVOE
OC0B enable
(USIWM1  DDA6) + OC1A enable
(USIWM1  USIWM0) + OC1B
enable
PVOV
OC0B
(USIWM1DDA6)  OC1A
USIWM1  USIWM0  DO +
(~USIWM1 USIWM0)  OC1B}
PTOE
0
0
0
DIEOE
PCINT7  PCIE0 + ADC7D
USISIE + (PCINT6  PCIE0) +
ADC6D
PCINT5  PCIE + ADC5D
DIEOV
PCINT7  PCIE0
USISIE + PCINT7  PCIE0
PCINT5  PCIE
DI
PCINT7/ICP1 input
DI/SDA/PCINT6 input
PCINT5 input
AIO
ADC7 input
ADC6 input
ADC5 input
Table 12-5. Overriding Signals for Alternate Functions in PA4..PA2
58
Signal Name
PA4/ADC4/USCK/SCL/T1/PCINT4
PA3/ADC3/T0/PCINT3
PA2/ADC2/AIN1/PCINT2
PUOE
0
0
0
PUOV
0
0
0
DDOE
USIWM1
0
0
DDOV
USI_SCL_HOLD + PORTA4) ADC4D
0
0
PVOE
USIWM1  ADC4D
0
0
PVOV
0
0
0
PTOE
USI_PTOE
0
0
DIEOE
USISIE + (PCINT4  PCIE0) + ADC4D
(PCINT3  PCIE0) + ADC3D
PCINT2  PCIE + ADC2D
DIEOV
USISIE + (PCINT4  PCIE0)
PCINT3  PCIE0
PCINT3  PCIE0
DI
USCK/SCL/T1/PCINT4 input
PCINT1 input
PCINT0 input
AIO
ADC4 input
ADC3 input
ADC2/analog comparator
negative input
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 12-6. Overriding Signals for Alternate Functions in PA1..PA0
Signal Name
PA1/ADC1/AIN0/PCINT1
PA0/ADC0/AREF/PCINT0
PUOE
0
RESET  (REFS1  REFS0 + REFS1  REFS0)
PUOV
0
0
DDOE
0
RESET  (REFS1  REFS0 + REFS1  REFS0)
DDOV
0
0
PVOE
0
RESET  (REFS1  REFS0 + REFS1  REFS0)
PVOV
0
0
PTOE
0
0
DIEOE
PCINT1  PCIE0 + ADC1D
PCINT0  PCIE0 + ADC0D
DIEOV
PCINT1  PCIE0
PCINT0  PCIE0
DI
PCINT1 input
PCINT0 input
AIO
ADC1/analog comparator positive input
ADC1 input analog reference
12.3.2 Alternate Functions of Port B
The port B pins with alternate function are shown in Table 12-7.
Table 12-7. Port B Pins Alternate Functions
Port Pin
PB0
PB1
PB2
PB3
Alternate Function
XTAL1:
Crystal oscillator input.
PCINT8:
Pin change interrupt 1 source 8.
XTAL2:
Crystal oscillator output.
PCINT9:
Pin change interrupt 1 source 9.
INT0:
External interrupt 0 input.
OC0A:
Timer/Counter0 compare match A output.
CKOUT:
System clock output.
PCINT10:
Pin change interrupt 1 source 10.
RESET:
Reset pin.
dW:
debugWire I/O.
PCINT11:
Pin change interrupt 1 source 11.
• Port B, Bit 0 – XTAL1/PCINT8
XTAL1: Chip clock oscillator pin 1. Used for all chip clock sources except the internal calibrated RC oscillator. When used as
a clock pin, the pin cannot be used as an I/O pin. When using internal calibrated RC oscillator as a chip clock source, PB0
serves as an ordinary I/O pin.
PCINT8: Pin change interrupt source 8. The PB0 pin can serve as an external interrupt source for pin change interrupt 1.
• Port B, Bit 1 – XTAL2/PCINT9
XTAL2: Chip clock oscillator pin 2. Used as clock pin for all chip clock sources except the internal calibrated RC oscillator
and external clock. When used as a clock pin, the pin cannot be used as an I/O pin. When using internal calibrated RC
oscillator or external clock as a chip clock sources, PB1 serves as an ordinary I/O pin.
PCINT9: Pin change interrupt source 9. The PB1 pin can serve as an external interrupt source for pin change interrupt 1.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
59
• Port B, Bit 2 – INT0/OC0A/CKOUT/PCINT10
INT0: External interrupt request 0.
OC0A: Output compare match output: The PB2 pin can serve as an external output for the Timer/Counter 0 compare match
A. The PB2 pin has to be configured as an output (DDB2 set (one)) to serve this function. The OC0A pin is also the output
pin for the PWM mode timer function.
CKOUT - System clock output: The system clock can be output on the PB2 pin. The system clock will be output if the
CKOUT fuse is programmed, regardless of the PORTB2 and DDB2 settings. It will also be output during reset.
PCINT10: Pin change interrupt source 10. The PB2 pin can serve as an external interrupt source for pin change interrupt 1.
• Port B, Bit 3 – RESET/dW/PCINT11
RESET: External reset input is active low and enabled by un-programming (“1”) the RST- DISBL fuse. Pull-up is activated
and output driver and digital input are deactivated when the pin is used as the RESET pin.
dW: When the debugWIRE enable (DWEN) fuse is programmed and lock bits are un-programmed, the debugWIRE system
within the target device is activated. The RESET port pin is configured as a wire-AND (open-drain) bi-directional I/O pin with
pull-up enabled and becomes the communication gateway between target and emulator.
PCINT11: Pin change interrupt source 11. The PB3 pin can serve as an external interrupt source for pin change interrupt 1.
Table 12-8 and Table 12-9 on page 61 relate the alternate functions of Port B to the overriding signals shown
in Figure 12-5 on page 54.
Table 12-8. Overriding Signals for Alternate Functions in PB3..PB2
Signal Name PB3/RESET/dW/PCINT11
(1)
PUOE
RSTDISBL + DEBUGWIRE_ENABLE
PUOV
1
RSTDISBL
+ DEBUGWIRE_ENABLE
DDOV
DEBUGWIRE_ENABLE
PVOE
(1)
RSTDISBL
PVOV
0
PTOE
0
CKOUT
 debugWire Transmit
(2)
+ DEBUGWIRE_ENABLE
1'b1
CKOUT + OC0A enable
CKOUT  System Clock + CKOUT  OC0A
0
(1)
RSTDISBL
(2)
+ DEBUGWIRE_ENABLE
(2)
DIEOV
DEBUGWIRE_ENABLE
PCIE1)
DI
dW/PCINT11 Input
AIO
Notes:
60
(2)
(2)
DIEOE
CKOUT
0
(1)
DDOE
PB2/INT0/OC0A/CKOUT/PCINT10
(2)
+ (RSTDISBL
+ PCINT11 PCIE1 PCINT10  PCIE1 + INT0
(1)
PCINT11 
PCINT10  PCIE1 + INT0
INT0/PCINT10 Input
1.
RSTDISBL is 1 when the fuse is “0” (programmed).
2.
DebugWIRE is enabled when DWEN fuse is programmed and lock bits are un-programmed.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 12-9. Overriding Signals for Alternate Functions in PB1..PB0
Signal Name
PB0/XTAL1/PCINT8
PUOE
EXT_OSC
EXT_CLOCK(2)+ EXT_OSC(1)
PUOV
0
0
(1)
DDOE
EXT_OSC
EXT_CLOCK(2) + EXT_OSC(1)
DDOV
0
0
(1)
PVOE
EXT_OSC
EXT_CLOCK(2) + EXT_OSC(1)
PVOV
0
0
PTOE
0
0
DIEOE
EXT_OSC (1)+ PCINT9  PCIE1
EXT_CLOCK(2) + EXT_OSC(1) + (PCINT8  PCIE1)
DIEOV
EXT_OSC(1)  PCINT9  PCIE1
(EXT_CLOCK(2)  PWR_DOWN) + (EXT_CLOCK(2) 
EXT_OSC(1)  PCINT8  PCIE1)
DI
PCINT9 input
CLOCK/PCINT8 input
AIO
Notes:
12.4
PB1/XTAL2/PCINT9
(1)
1.
XTAL2
XTAL1
EXT_OSC = crystal oscillator or low frequency crystal oscillator is selected as system clock.
2.
EXT_CLOCK = external clock is selected as system clock.
Register Description
12.4.1 MCUCR – MCU Control Register
.
Bit
7
6
5
4
3
2
1
0
BODS
PUD
SE
SM1
SM0
BODSE
ISC01
ISC00
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R
R
Initial Value
0
0
0
0
0
0
0
0
MCUCR
• Bit 6 – PUD: Pull-up Disable
When this bit is written to logical one, the pull-ups in the I/O ports are disabled even if the DDxn and PORTxn registers are
configured to enable the pull-ups ({DDxn, PORTxn} = 0b01). See Section 12.2.1 “Configuring the Pin” on page 50 for more
details about this feature.
12.4.2 PORTA – Port A Data Register
Bit
7
6
5
4
3
2
1
0
0x1B (0x3B)
PORTA7
PORTA6
PORTA5
PORTA4
PORTA3
PORTA2
PORTA1
PORTA0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
PORTA
12.4.3 DDRA – Port A Data Direction Register
Bit
7
6
5
4
3
2
1
0
0x1A (0x3A)
DDA7
DDA6
DDA5
DDA4
DDA3
DDA2
DDA1
DDA0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
DDRB
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
61
12.4.4 PINA – Port A Input Pins Address
Bit
7
6
5
4
3
2
1
0
0x19 (0x39)
PINA7
PINA6
PINA5
PINA4
PINA3
PINA2
PINA1
PINA0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
N/A
N/A
N/A
N/A
N/A
N/A
5
4
3
2
1
0
PINB
12.4.5 PORTB – Port B Data Register
Bit
7
6
0x18 (0x38)
–
–
Read/Write
R
R
R
R
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
PORTB3 PORTB2 PORTB1 PORTB0
PORTB
12.4.6 DDRB – Port B Data Direction Register
Bit
7
6
0x17 (0x37)
–
–
5
Read/Write
R
R
R
Initial Value
0
0
0
4
3
2
1
0
DDB3
DDB2
DDB1
DDB0
R
R/W
R/W
R/W
R/W
0
0
0
0
0
DDRB
12.4.7 PINB – Port BInput Pins Address
62
Bit
7
6
0x16 (0x36)
–
–
Read/Write
R
R
R
Initial Value
0
0
N/A
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
5
4
3
2
1
0
PINB3
PINB2
PINB1
PINB0
R
R/W
R/W
R/W
R/W
N/A
N/A
N/A
N/A
N/A
PINB
13.
8-bit Timer/Counter0 with PWM
13.1
Features
●
●
●
●
●
●
●
Double buffered output compare registers
Clear timer on compare match (auto reload)
Glitch free, phase correct pulse width modulator (PWM)
Variable PWM period
Frequency generator
Three independent interrupt sources (TOV0, OCF0A, and OCF0B)
Overview
Timer/Counter 0 is a general purpose 8-bit Timer/Counter module, with two independent out- put compare units, and with
PWM support. It allows accurate program execution timing (event management) and wave generation.
A simplified block diagram of the 8-bit Timer/Counter is shown in Figure 13-1. For the actual placement of I/O pins, refer to
Figure 1-1 on page 3. CPU accessible I/O registers, including I/O bits and I/O pins, are shown in bold. The device-specific
I/O register and bit locations are listed in the Section 13.9 “Register Description” on page 73.
Figure 13-1. 8-bit Timer/Counter Block Diagram
TOVn (Int. Req.)
Count
Clear
Direction
Clock Select
Control Logic
clkTn
TOP
BOTTOM
=
=
Edge
Detector
Tn
(from Prescaler)
Timer/Counter
TCNTn
0
OCnA (Int. Req.)
Waveform
Generation
=
OCnA
OCRnA
DATA BUS
13.2
Two independent output compare units
Fixed
TOP
Value
OCnB (Int. Req.)
Waveform
Generation
=
OCnB
OCRnB
TCCRnA
TCCRnB
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
63
13.2.1 Registers
The Timer/Counter (TCNT0) and output compare registers (OCR0A and OCR0B) are 8-bit registers. Interrupt request
(abbreviated to Int.Req. in the figure) signals are all visible in the Timer/Counter 0 interrupt flag register (TIFR0). All
interrupts are individually masked with the timer interrupt mask register (TIMSK0). TIFR0 and TIMSK0 are not shown in the
figure.
The Timer/Counter can be clocked internally, via the prescaler, or by an external clock source on the T0 pin. The Clock
Select logic block controls which clock source and edge the Timer/Counter uses to increment (or decrement) its value. The
Timer/Counter is inactive when no clock source is selected. The output from the clock select logic is referred to as the timer
clock (clkT0).
The double buffered output compare registers (OCR0A and OCR0B) is compared with the Timer/Counter value at all times.
The result of the compare can be used by the waveform generator to generate a PWM or variable frequency output on the
output compare pins (OC0A and OC0B). See Section 13.5 “Output Compare Unit” on page 65 for details. The compare
match event will also set the compare flag (OCF0A or OCF0B) which can be used to generate an output compare interrupt
request.
13.2.2 Definitions
Many register and bit references in this section are written in general form. A lower case “n” replaces the Timer/Counter
number, in this case 0. A lower case “x” replaces the output compare unit, in this case compare unit A or compare unit B.
However, when using the register or bit defines in a program, the precise form must be used, i.e., TCNT0 for accessing
Timer/Counter 0 counter value and so on.
The definitions in Table are also used extensively throughout the document.
Table 13-1. Definitions
13.3
Parameter
Definition
BOTTOM
The counter reaches the BOTTOM when it becomes 0x00.
MAX
The counter reaches its MAXimum when it becomes 0xFF (decimal 255).
TOP
The counter reaches the TOP when it becomes equal to the highest value in the count sequence. The
TOP value can be assigned to be the fixed value 0xFF (MAX) or the value stored in the OCR0A register.
The assignment is dependent on the mode of operation.
Timer/Counter Clock Sources
The Timer/Counter can be clocked by an internal or an external clock source. The clock source is selected by the clock
select logic which is controlled by the clock select (CS02:0) bits located in the Timer/Counter control register (TCCR0B). For
details on clock sources and prescaler, see Section 15. “Timer/Counter Prescaler” on page 103.
13.4
Counter Unit
The main part of the 8-bit Timer/Counter is the programmable bi-directional counter unit. Figure 13-2 shows a block diagram
of the counter and its surroundings.
Figure 13-2. Counter Unit Block Diagram
TOVn
(Int. Req.)
DATA BUS
Clock Select
count
TCNTn
clear
Control Logic
clkTn
Edge
Detector
direction
(from Prescaler)
bottom
64
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
top
Tn
Signal description (internal signals):
count
Increment or decrement TCNT0 by 1.
direction
Select between increment and decrement.
clear
Clear TCNT0 (set all bits to zero).
clkTn
Timer/Counter clock, referred to as clkT0 in the following.
top
Signalize that TCNT0 has reached maximum value.
bottom
Signalize that TCNT0 has reached minimum value (zero).
Depending on the mode of operation used, the counter is cleared, incremented, or decremented at each timer clock (clkT0).
clkT0 can be generated from an external or internal clock source, selected by the clock select bits (CS02:0). When no clock
source is selected (CS02:0 = 0) the timer is stopped. However, the TCNT0 value can be accessed by the CPU, regardless of
whether clkT0 is present or not. A CPU write overrides (has priority over) all counter clear or count operations.
The counting sequence is determined by the setting of the WGM01 and WGM00 bits located in the Timer/Counter control
register A (TCCR0A) and the WGM02 bit located in the Timer/Counter control register B (TCCR0B). There are close
connections between how the counter behaves (counts) and how waveforms are generated on the output compare output
(OC0A). For more details about advanced counting sequences and waveform generation, see Section 13.7 “Modes of
Operation” on page 67.
The Timer/Counter overflow flag (TOV0) is set according to the mode of operation selected by the WGM01:0 bits. TOV0 can
be used for generating a CPU interrupt.
13.5
Output Compare Unit
The 8-bit comparator continuously compares TCNT0 with the output compare registers (OCR0A and OCR0B). Whenever
TCNT0 equals OCR0A or OCR0B, the comparator signals a match. A match will set the output compare flag (OCF0A or
OCF0B) at the next timer clock cycle. If the corresponding interrupt is enabled, the output compare flag generates an output
compare interrupt. The output compare flag is automatically cleared when the interrupt is executed. Alternatively, the flag
can be cleared by software by writing a logical one to its I/O bit location. The waveform generator uses the match signal to
generate an output according to the operating mode set by the WGM02:0 bits and compare output mode (COM0x1:0) bits.
The max and bottom signals are used by the waveform generator for handling the special cases of the extreme values in
some modes of operation. See Section 13.7 “Modes of Operation” on page 67.
Figure 13-3 shows a block diagram of the output compare unit.
Figure 13-3. Output Compare Unit, Block Diagram
DATA BUS
OCRnx
TCNTn
=
(8-bit Comparator)
OCFnx (Int. Req.)
top
bottom
Waveform Generator
OCnx
FOCn
WGMn1:0
COMnx1:0
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
65
The OCR0x registers are double buffered when using any of the pulse width modulation (PWM) modes. For the normal and
clear timer on compare (CTC) modes of operation, the double buffering is disabled. The double buffering synchronizes the
update of the OCR0x compare registers to either top or bottom of the counting sequence. The synchronization prevents the
occurrence of odd-length, non-symmetrical PWM pulses, thereby making the output glitch-free.
The OCR0x register access may seem complex, but this is not the case. When the double buffering is enabled, the CPU has
access to the OCR0x buffer register, and if double buffering is disabled the CPU will access the OCR0x directly.
13.5.1 Force Output Compare
In non-PWM waveform generation modes, the match output of the comparator can be forced by writing a logical one to the
force output compare (0x) bit. Forcing compare match will not set the OCF0x flag or reload/clear the timer, but the OC0x pin
will be updated as if a real compare match had occurred (the COM0x1:0 bits settings define whether the OC0x pin is set,
cleared, or toggled).
13.5.2 Compare Match Blocking by TCNT0 Write
All CPU write operations to the TCNT0 Register will block any Compare Match that occur in the next timer clock cycle, even
when the timer is stopped. This feature allows OCR0x to be initialized to the same value as TCNT0 without triggering an
interrupt when the Timer/Counter clock is enabled.
13.5.3 Using the Output Compare Unit
Since writing TCNT0 in any mode of operation will block all compare matches for one timer clock cycle, there are risks
involved in changing TCNT0 when using the output compare unit, independently of whether the Timer/Counter is running or
not. If the value written to TCNT0 equals the OCR0x value, the compare match will be missed, resulting in incorrect
waveform generation. Similarly, do not write the TCNT0 value equal to bottom when the counter is down-counting.
The setup of the OC0x should be performed before setting the data direction register for the port pin to output. The easiest
way of setting the OC0x value is to use the force output compare (0x) strobe bits in normal mode. The OC0x registers keep
their values even when changing between waveform generation modes.
Be aware that the COM0x1:0 bits are not double buffered together with the compare value. Changes to the COM0x1:0 bits
will take effect immediately.
13.6
Compare Match Output Unit
The compare output mode (COM0x1:0) bits have two functions. The waveform generator uses the COM0x1:0 bits for
defining the output compare (OC0x) state at the next compare match. Also, the COM0x1:0 bits control the OC0x pin output
source. Figure 13-4 on page 67 shows a simplified schematic of the logic affected by the COM0x1:0 bit setting. The I/O
registers, I/O bits, and I/O pins in the figure are shown in bold. Only the parts of the general I/O port control registers (DDR
and PORT) that are affected by the COM0x1:0 bits are shown. When referring to the OC0x state, the reference is for the
internal OC0x register, not the OC0x pin. If a system reset occurs, the OC0x register is reset to “0”.
66
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Figure 13-4. Compare Match Output Unit, Schematic
COMnx1
COMnx0
FOCn
Waveform
Generator
D
Q
1
OCnx
Pin
OCnx
0
DATA BUS
D
Q
PORT
D
Q
DDR
clkI/O
The general I/O port function is overridden by the output compare (OC0x) from the waveform generator if either of the
COM0x1:0 bits are set. However, the OC0x pin direction (input or output) is still controlled by the data direction register
(DDR) for the port pin. The data direction register bit for the OC0x pin (DDR_OC0x) must be set as output before the OC0x
value is visible on the pin. The port override function is independent of the waveform generation mode.
The design of the output compare pin logic allows initialization of the OC0x state before the output is enabled. Note that
some COM0x1:0 bit settings are reserved for certain modes of operation, see
Section 13.9 “Register Description” on page 73.
13.6.1 Compare Output Mode and Waveform Generation
The waveform generator uses the COM0x1:0 bits differently in normal, CTC, and PWM modes. For all modes, setting the
COM0x1:0 = 0 tells the waveform generator that no action on the OC0x register is to be performed on the next compare
match. For compare output actions in the non-PWM modes refer to Table 13-2 on page 73. For fast PWM mode, refer to
Table 13-3 on page 73, and for phase correct PWM refer to Table 13-4 on page 73.
A change of the COM0x1:0 bit states will have effect at the first compare match after the bits are written. For non-PWM
modes, the action can be forced to have immediate effect by using the 0x strobe bits.
13.7
Modes of Operation
The mode of operation, i.e., the behavior of the Timer/Counter and the output compare pins, is defined by the combination of
the waveform generation mode (WGM02:0) and compare output mode (COM0x1:0) bits. The compare output mode bits do
not affect the counting sequence, while the waveform generation mode bits do. The COM0x1:0 bits control whether the
PWM output generated should be inverted or not (inverted or non-inverted PWM). For non-PWM modes the COM0x1:0 bits
control whether the output should be set, cleared, or toggled at a compare match (See Section 13.7 “Modes of Operation” on
page 67).
For detailed timing information refer to Figure 13-8 on page 71, Figure 13-9 on page 72, Figure 13-10 on page 72 and
Figure 13-11 on page 72 in Section 13.8 “Timer/Counter Timing Diagrams” on page 71.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
67
13.7.1 Normal Mode
The simplest mode of operation is the normal mode (WGM02:0 = 0). In this mode, the counting direction is always up
(incrementing), and no counter clear is performed. The counter simply overruns when it passes its maximum 8-bit value
(top = 0xFF) and then restarts from the bottom (0x00). In normal operation the Timer/Counter overflow flag (TOV0) will be
set on the same timer clock cycle on which the TCNT0 becomes zero. The TOV0 flag in this case behaves like a ninth bit,
except that it is only set, not cleared. However, combined with the timer overflow interrupt that automatically clears the TOV0
flag, the timer resolution can be increased by software. There are no special cases to consider in the normal mode. A new
counter value can be written anytime.
The output compare unit can be used to generate interrupts at some given time. Using the output compare to generate
waveforms in normal mode is not recommended, since this will occupy too much CPU time.
13.7.2 Clear Timer on Compare Match (CTC) Mode
In clear timer on compare, or CTC, mode (WGM02:0 = 2), the OCR0A register is used to manipulate the counter resolution.
In CTC mode, the counter is cleared to zero when the counter value (TCNT0) matches the OCR0A. The OCR0A defines the
top value for the counter, hence also its resolution. This mode allows greater control of the compare match output frequency.
It also simplifies the operation of counting external events.
The timing diagram for the CTC mode is shown in Figure 13-5. The counter value (TCNT0) increases until a compare match
occurs between TCNT0 and OCR0A, and then counter (TCNT0) is cleared.
Figure 13-5. CTC Mode, Timing Diagram
OCnx Interrupt Flag Set
TCNTn
OCn
(Toggle)
Period
(COMnx1:0 = 1)
1
2
3
4
An interrupt can be generated each time the counter value reaches the top value by using the OCF0A flag. If the interrupt is
enabled, the interrupt handler routine can be used for updating the top value. However, changing top to a value close to
bottom when the counter is running with no or a low prescaler value must be done with care since the CTC mode does not
have the double buffering feature. If the new value written to OCR0A is lower than the current value of TCNT0, the counter
will miss the compare match. The counter will then have to count to its maximum value (0xFF) and wrap around starting at
0x00 before the compare match can occur.
For generating a waveform output in CTC mode, the OC0A output can be set to toggle its logical level on each compare
match by setting the compare output mode bits to toggle mode (COM0A1:0 = 1). The OC0A value will not be visible on the
port pin unless the data direction for the pin is set to output. The waveform generated will have a maximum frequency of
f0 = fclk_I/O/2 when OCR0A is set to zero (0x00). The waveform frequency is defined by the following equation:
f clk_I/O
f OCnx = ---------------------------------------------------2  N   1 + OCRnx 
The variable N represents the prescale factor (1, 8, 64, 256, or 1024).
As for the normal mode of operation, the TOV0 flag is set on the same timer clock cycle on which the counter counts from
max to 0x00.
68
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
13.7.3 Fast PWM Mode
The fast pulse width modulation, or fast PWM, mode (WGM02:0 = 3 or 7) provides a high-frequency PWM waveform
generation option. The fast PWM mode differs from the other PWM option by its single-slope operation. The counter counts
from bottom to top then restarts from bottom. Top is defined as 0xFF when WGM2:0 = 3, and as OCR0A when WGM2:0 = 7.
In non-inverting compare output mode, the output compare (OC0x) is cleared on the compare match between TCNT0 and
OCR0x, and set at bottom. In inverting compare output mode, the output is set on compare match and cleared at bottom.
Due to the single-slope operation, the operating frequency of the fast PWM mode can be twice as high as the phase correct
PWM mode that uses dual-slope operation.
This high frequency makes the fast PWM mode well suited for power regulation, rectification, and DAC applications. High
frequency allows the use of physically smaller external components (coils, capacitors, etc.), and hence reduces total system
cost.
In fast PWM mode, the counter is incremented until the counter value matches the TOP value. The counter is then cleared at
the following timer clock cycle. The timing diagram for the fast PWM mode is shown in Figure 13-6. The TCNT0 value is in
the timing diagram shown as a histogram for illustrating the single-slope operation. The diagram includes non-inverted and
inverted PWM outputs. The small horizontal line marks on the TCNT0 slopes represent Compare Matches between OCR0x
and TCNT0.
Figure 13-6. Fast PWM Mode, Timing Diagram
OCRnx Interrupt
Flag Set
OCRnx Update and
TOVn Interrupt Flag Set
TCNTn
OCnx
(COMnx1:0 = 2)
OCnx
(COMnx1:0 = 3)
Period
1
2
3
4
5
6
7
The Timer/Counter overflow flag (TOV0) is set each time the counter reaches TOP. If the interrupt is enabled, the interrupt
handler routine can be used for updating the compare value.
In fast PWM mode, the compare unit allows generation of PWM waveforms on the OC0x pins. Setting the COM0x1:0 bits to
two will produce a non-inverted PWM, and an inverted PWM output can be generated by setting the COM0x1:0 bits to three.
Setting the COM0A1:0 bits to one allows the AC0A pin to toggle on compare matches if the WGM02 bit is set. This option is
not available for the OC0B pin (see Table 13-3 on page 73). The actual OC0x value will only be visible on the port pin if the
data direction for the port pin is set as output. The PWM waveform is generated by setting (or clearing) the OC0x register at
the compare match between OCR0x and TCNT0, and clearing (or setting) the OC0x register at the timer clock cycle when
the counter is cleared (changes from top to bottom).
The PWM frequency for the output can be calculated by the following equation:
f clk_I/O
f OCnxPWM = ------------------N  256
The variable N represents the prescale factor (1, 8, 64, 256, or 1024).
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
69
The extreme values for the OCR0A register represent special cases when generating a PWM waveform output in the fast
PWM mode. If the OCR0A is set equal to bottom, the out- put will be a narrow spike for each max+1 timer clock cycle.
Setting the OCR0A equal to max will result in a constantly high or low output (depending on the polarity of the output set by
the COM0A1:0 bits).
A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by setting OC0x to toggle its logical
level on each compare match (COM0x1:0 = 1). The waveform generated will have a maximum frequency of f0 = fclk_I/O/2
when OCR0A is set to zero. This feature is similar to the OC0A toggle in CTC mode, except the double buffer feature of the
output compare unit is enabled in the fast PWM mode.
13.7.4 Phase Correct PWM Mode
The phase correct PWM mode (WGM02:0 = 1 or 5) provides a high resolution phase correct PWM waveform generation
option. The phase correct PWM mode is based on a dual-slope operation. The counter counts repeatedly from bottom to top
and then from top to bottom. Top is defined as 0xFF when WGM2:0 = 1, and as OCR0A when WGM2:0 = 5. In non-inverting
compare output mode, the output compare (OC0x) is cleared on the compare match between TCNT0 and OCR0x while
up-counting, and set on the compare match while down-counting. In inverting output compare mode, the operation is
inverted. The dual-slope operation has lower maximum operation frequency than single slope operation. However, due to
the symmetric feature of the dual-slope PWM modes, these modes are preferred for motor control applications.
In phase correct PWM mode the counter is incremented until the counter value matches TOP. When the counter reaches
TOP, it changes the count direction. The TCNT0 value will be equal to TOP for one timer clock cycle. The timing diagram for
the phase correct PWM mode is shown on Figure 13-7. The TCNT0 value is in the timing diagram, which is shown as a
histogram for illustrating the dual-slope operation. The diagram includes non-inverted and inverted PWM outputs. The small
horizontal lines on the TCNT0 slopes represent compare matches between OCR0x and TCNT0.
Figure 13-7. Phase Correct PWM Mode, Timing Diagram
OCnx Interrupt
Flag Set
OCRnx Update
TOVn Interrupt
Flag Set
TCNTn
OCnx
(COMnx1:0 = 2)
OCnx
(COMnx1:0 = 3)
Period
1
2
3
The Timer/Counter overflow flag (TOV0) is set each time the counter reaches bottom. The interrupt flag can be used to
generate an interrupt each time the counter reaches the bottom value.
70
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
In phase correct PWM mode, the compare unit allows generation of PWM waveforms on the OC0x pins. Setting the
COM0x1:0 bits to two will produce a non-inverted PWM. An inverted PWM output can be generated by setting the
COM0x1:0 bits to three. Setting the COM0A0 bits to one allows the OC0A pin to toggle on compare matches if the WGM02
bit is set. This option is not available for the OC0B pin (See Table 13-4 on page 73). The actual OC0x value will only be
visible on the port pin if the data direction for the port pin is set as output. The PWM waveform is generated by clearing (or
setting) the OC0x register at the compare match between OCR0x and TCNT0 when the counter increments, and setting (or
clearing) the OC0x register at compare match between OCR0x and TCNT0 when the counter decrements. The PWM
frequency for the output when using phase correct PWM can be calculated by the following equation:
f clk_I/O
f OCnxPCPWM = ------------------N  510
The variable N represents the prescale factor (1, 8, 64, 256, or 1024).
The extreme values for the OCR0A register represent special cases when generating a PWM waveform output in the phase
correct PWM mode. If the OCR0A is set equal to bottom, the output will be continuously low, and if set equal to max the
output will be continuously high for non-inverted PWM mode. For inverted PWM, the output will have the opposite logic
values.
At the very start of period 2 in Figure 13-7 on page 70 OCn has a transition from high to low even though there is no compare
match. The point of this transition is to guarantee symmetry around bottom. There are two cases that give a transition
without a compare match.
● OCR0A changes its value from MAX, as in Figure 13-7 on page 70. When the OCR0A value is MAX the OCn pin
value is the same as the result of a down-counting compare match. To ensure symmetry around BOTTOM the OCn
value at MAX must correspond to the result of an up-counting compare match.
●
13.8
The timer starts counting from a value higher than the one in OCR0A, and for that reason misses the compare match
and, hence, the OCn change that would have happened on the way up.
Timer/Counter Timing Diagrams
The Timer/Counter is a synchronous design, and the timer clock (clkT0) is, therefore, shown as a clock enable signal in the
following figures. The figures include information on when interrupt flags are set. Figure 13-8 contains timing data for basic
Timer/Counter operation.The figure shows the count sequence close to the max value in all modes other than phase correct
PWM mode.
Figure 13-8. Timer/Counter Timing Diagram, no Prescaling
clkI/O
clkTn
(clkI/O/1)
TCNTn
MAX - 1
MAX
BOTTOM
BOTTOM + 1
TOVn
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
71
Figure 13-9 shows the same timing data, but with the prescaler enabled.
Figure 13-9. Timer/Counter Timing Diagram, with Prescaler (fclk_I/O/8)
clkI/O
clkTn
(clkI/O/8)
TCNTn
MAX - 1
MAX
BOTTOM
BOTTOM + 1
TOVn
Figure 13-10 shows the setting of OCF0B in all modes and OCF0A in all modes except CTC mode and PWM mode, where
OCR0A is TOP.
Figure 13-10. Timer/Counter Timing Diagram, Setting of OCF0x, with Prescaler (fclk_I/O/8)
clkI/O
clkTn
(clkI/O/8)
TCNTn
OCRnx - 1
OCRnx
OCRnx
OCRnx + 1
OCRnx + 2
OCRnx Value
OCFnx
Figure 13-11 shows the setting of OCF0A and the clearing of TCNT0 in CTC mode and fast PWM mode where OCR0A is
TOP.
Figure 13-11. Timer/Counter Timing Diagram, Clear Timer on Compare Match mode, with Prescaler (fclk_I/O/8)
clkI/O
clkTn
(clkI/O/8)
TCNTn
(CTC)
OCRnx
OCFnx
72
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
TOP - 1
TOP
BOTTOM
TOP
BOTTOM + 1
13.9
Register Description
13.9.1 TCCR0A – Timer/Counter Control Register A
Bit
7
0x30 (0x50)
6
5
4
COM0A1 COM0A0 COM0B1 COM0B0
3
2
1
0
–
–
WGM01
WGM00
Read/Write
R/W
R/W
R/W
R/W
R
R
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TCCR0A
• Bits 7:6 – COM0A1:0: Compare Match Output A Mode
These bits control the output compare pin (OC0A) behavior. If one or both of the COM0A1:0 bits are set, the OC0A output
overrides the normal port functionality of the I/O pin it is connected to. However, note that the data direction register (DDR)
bit corresponding to the OC0A pin must be set in order to enable the output driver.
When OC0A is connected to the pin, the function of the COM0A1:0 bits depends on the WGM02:0 bit setting. Table 13-2
shows the COM0A1:0 bit functionality when the WGM02:0 bits are set to a normal or CTC mode (non-PWM).
Table 13-2. Compare Output Mode, non-PWM Mode
COM01
COM00
Description
0
0
Normal port operation, OC0A disconnected.
0
1
Toggle OC0A on compare match
1
0
Clear OC0A on compare match
1
1
Set OC0A on compare match
Table 13-3 shows the COM0A1:0 bit functionality when the WGM01:0 bits are set to fast PWM mode.
Table 13-3. Compare Output Mode, Fast PWM Mode(1)
COM01
COM00
0
0
Normal port operation, OC0A disconnected.
0
1
WGM02 = 0: Normal port operation, OC0A disconnected.
WGM02 = 1: Toggle OC0A on compare match.
1
0
Clear OC0A on compare match, set OC0A at BOTTOM
(non-inverting mode)
1
Note:
1.
Description
Set OC0A on compare match, clear OC0A at BOTTOM
(inverting mode)
A special case occurs when OCR0A equals TOP and COM0A1 is set. In this case, the compare match is
ignored, but the set or clear is done at BOTTOM. See Section 13.7.3 “Fast PWM Mode” on page 69 for more
details.
1
Table 13-4 shows the COM0A1:0 bit functionality when the WGM02:0 bits are set to phase correct PWM mode.
Table 13-4. Compare Output Mode, Phase Correct PWM Mode(1)
COM0A1
COM0A0
0
0
Normal port operation, OC0A disconnected.
0
1
WGM02 = 0: Normal port operation, OC0A disconnected.
WGM02 = 1: Toggle OC0A on compare match.
1
0
Clear OC0A on compare match when up-counting. Set OC0A on compare match
when down-counting.
1
Note:
1.
Description
Set OC0A on compare match when up-counting. Clear OC0A on compare match
when down-counting.
A special case occurs when OCR0A equals TOP and COM0A1 is set. In this case, the compare match is
ignored, but the set or clear is done at TOP. See Section 13.7.4 “Phase Correct PWM Mode” on page 70 for
more details.
1
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
73
• Bits 5:4 – COM0B1:0: Compare Match Output B Mode
These bits control the output compare pin (OC0B) behavior. If one or both of the COM0B1:0 bits are set, the OC0B output
overrides the normal port functionality of the I/O pin it is connected to. However, note that the data direction register (DDR)
bit corresponding to the OC0B pin must be set in order to enable the output driver.
When OC0B is connected to the pin, the function of the COM0B1:0 bits depends on the WGM02:0 bit setting. Table 13-2 on
page 73 shows the COM0A1:0 bit functionality when the WGM02:0 bits are set to a normal or CTC mode (non-PWM).
Table 13-5. Compare Output Mode, non-PWM Mode
COM01
COM00
0
0
Description
Normal port operation, OC0B disconnected.
0
1
Toggle OC0B on compare match
1
0
Clear OC0B on compare match
1
1
Set OC0B on compare match
Table 13-3 on page 73 shows the COM0B1:0 bit functionality when the WGM02:0 bits are set to fast PWM mode.
Table 13-6. Compare Output Mode, Fast PWM Mode(1)
COM01
COM00
0
0
Normal port operation, OC0B disconnected.
0
1
Reserved
1
0
Clear OC0B on compare match, set OC0B at BOTTOM (non-inverting mode)
Note:
1
1.
Description
1
Set OC0B on compare match, clear OC0B at BOTTOM (inverting mode)
A special case occurs when OCR0B equals TOP and COM0B1 is set. In this case, the compare match is
ignored, but the set or clear is done at BOTTOM. See Section 13.7.3 “Fast PWM Mode” on page 69 for more
details.
Table 13-4 on page 73 shows the COM0B1:0 bit functionality when the WGM02:0 bits are set to phase correct PWM mode.
Table 13-7. Compare Output Mode, Phase Correct PWM Mode(1)
COM0A1
COM0A0
0
0
Normal port operation, OC0B disconnected.
0
1
Reserved
1
0
Clear OC0B on compare match when up-counting. Set OC0B on compare match
when down-counting.
1
Note:
1.
Description
Set OC0B on compare match when up-counting. Clear OC0B on compare match
when down-counting.
A special case occurs when OCR0B equals TOP and COM0B1 is set. In this case, the compare match is
ignored, but the set or clear is done at TOP. See Section 13.7.4 “Phase Correct PWM Mode” on page 70 for
more details.
1
• Bits 3, 2 – Res: Reserved Bits
These bits are reserved bits in the ATtiny24/44/84 and will always read as zero.
• Bits 1:0 – WGM01:0: Waveform Generation Mode
Combined with the WGM02 bit found in the TCCR0B register, these bits control the counting sequence of the counter, the
source for maximum (TOP) counter value, and what type of waveform generation to be used, see Table 13-8 on page 75.
Modes of operation supported by the Timer/Counter unit are: Normal mode (counter), clear timer on compare match (CTC)
mode, and two types of pulse width modulation (PWM) modes (see Section 13.7 “Modes of Operation” on page 67).
74
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 13-8. Waveform Generation Mode Bit Description
Timer/Counter Mode of
Operation
TOP
Update of
OCRx at
TOV Flag
Set on(1)
0
Normal
0xFF
Immediate
MAX
0
1
PWM, phase correct
1
0
CTC
0
1
1
4
1
0
5
1
6
1
Mode
WGM2
WGM1
WGM0
0
0
0
1
0
2
0
3
7
Note:
1.
0xFF
TOP
BOTTOM
OCRA
Immediate
MAX
Fast PWM
0xFF
BOTTOM
MAX
0
Reserved
–
–
–
0
1
PWM, phase correct
OCRA
TOP
BOTTOM
1
0
Reserved
–
–
–
1
1
MAX = 0xFF
BOTTOM = 0x00
1
Fast PWM
OCRA
BOTTOM
TOP
13.9.2 TCCR0B – Timer/Counter Control Register B
Bit
7
6
5
4
3
2
1
0
0x33 (0x53)
FOC0A
FOC0B
–
–
WGM02
CS02
CS01
CS00
Read/Write
W
W
R
R
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TCCR0B
• Bit 7 – FOC0A: Force Output Compare A
The FOC0A bit is only active when the WGM bits specify a non-PWM mode.
However, for ensuring compatibility with future devices, this bit must be set to logical zero when TCCR0B is written when
operating in PWM mode. When writing a logical one to the FOC0A bit, an immediate compare match is forced on the
waveform generation unit. The OC0A output is changed according to its COM0A1:0 bit settings. Note that the FOC0A bit is
implemented as a strobe. Therefore, it is the value present in the COM0A1:0 bits that determines the effect of the forced
compare.
A FOC0A strobe will not generate any interrupt, nor will it clear the timer in CTC mode using OCR0A as TOP.
The FOC0A bit is always read as zero.
• Bit 6 – FOC0B: Force Output Compare B
The FOC0B bit is only active when the WGM bits specify a non-PWM mode.
However, for ensuring compatibility with future devices, this bit must be set to logical zero when TCCR0B is written when
operating in PWM mode. When writing a logical one to the FOC0B bit, an immediate compare match is forced on the
waveform generation unit. The OC0B output is changed according to its COM0B1:0 bit settings. Note that the FOC0B bit is
implemented as a strobe. Therefore, it is the value present in the COM0B1:0 bits that determines the effect of the forced
compare.
A FOC0B strobe will not generate any interrupt, nor will it clear the timer in CTC mode using OCR0B as TOP.
The FOC0B bit is always read as zero.
• Bits 5:4 – Res: Reserved Bits
These bits are reserved bits in the Atmel® ATtiny24/44/84, and will always read as zero.
• Bit 3 – WGM02: Waveform Generation Mode
See the description in the Section 13.9.1 “TCCR0A – Timer/Counter Control Register A” on page 73.
• Bits 2:0 – CS02:0: Clock Select
The three clock select bits select the clock source to be used by the Timer/Counter.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
75
Table 13-9. Clock Select Bit Description
CS02
CS01
CS00
Description
0
0
0
No clock source (Timer/Counter stopped)
0
0
1
clkI/O/(no prescaling)
0
1
0
clkI/O/8 (from prescaler)
0
1
1
clkI/O/64 (from prescaler)
1
0
0
clkI/O/256 (from prescaler)
1
0
1
clkI/O/1024 (from prescaler)
1
1
0
External clock source on T0 pin. Clock on falling edge.
1
1
1
External clock source on T0 pin. Clock on rising edge.
If external pin modes are used for the Timer/Counter0, transitions on the T0 pin will clock the counter even if the pin is
configured as an output. This feature allows software control of the counting.
13.9.3 TCNT0 – Timer/Counter Register
Bit
7
6
5
4
Read/Write
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0x32 (0x52)
3
2
1
0
R/W
R/W
R/W
R/W
0
0
0
0
TCNT0[7:0]
TCNT0
The Timer/Counter register gives direct access, for both read and write operations, to the Timer/Counter unit 8-bit counter.
Writing to the TCNT0 register blocks (removes) the compare match on the following timer clock. Modifying the counter
(TCNT0) while the counter is running, introduces a risk of missing a compare match between TCNT0 and the OCR0x
registers.
13.9.4 OCR0A – Output Compare Register A
Bit
7
6
5
0x36 (0x56)
4
3
2
1
0
OCR0A[7:0]
OCR0A
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
The output compare register A contains an 8-bit value that is continuously compared with the counter value (TCNT0). A
match can be used to generate an output compare interrupt, or to generate a waveform output on the OC0A pin.
13.9.5 OCR0B – Output Compare Register B
Bit
7
6
5
4
Read/Write
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0x3C (0x5C)
3
2
1
0
R/W
R/W
R/W
R/W
0
0
0
0
OCR0B[7:0]
OCR0B
The output compare register B contains an 8-bit value that is continuously compared with the counter value (TCNT0). A
match can be used to generate an output compare interrupt, or to generate a waveform output on the OC0B pin.
76
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
13.9.6 TIMSK0 – Timer/Counter 0 Interrupt Mask Register
Bit
7
6
5
4
3
2
1
0
0x39 (0x59)
–
–
–
–
–
OCIE0B
OCIE0A
TOIE0
Read/Write
R
R
R
R
R
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TIMSK0
• Bits 7..3 – Res: Reserved Bits
These bits are reserved bits in the Atmel® ATtiny24/44/84 and will always read as zero.
• Bit 2- OCIE0B: Timer/Counter 0 Output Compare Match B Interrupt Enable
When the OCIE0B bit is written to one, and the I-bit in the status register is set, the Timer/Counter 0 compare match B
interrupt is enabled. The corresponding interrupt is executed if a compare match in Timer/Counter occurs, i.e., when the
OCF0B bit is set in the Timer/Counter 0 interrupt flag register (TIFR0).
• Bit 1– OCIE0A: Timer/Counter0 Output Compare Match A Interrupt Enable
When the OCIE0A bit is written to one, and the I-bit in the status register is set, the Timer/Counter 0 compare match A
interrupt is enabled. The corresponding interrupt is executed if a compare match in Timer/Counter 0 occurs, i.e., when the
OCF0A bit is set in the Timer/Counter 0 interrupt flag register (TIFR0).
• Bit 0– TOIE0: Timer/Counter0 Overflow Interrupt Enable
When the TOIE0 bit is written to one, and the I-bit in the status register is set, the Timer/Counter 0 overflow interrupt is
enabled. The corresponding interrupt is executed if an overflow in Timer/Counter 0 occurs, i.e., when the TOV0 bit is set in
the Timer/Counter 0 interrupt flag register (TIFR0).
13.9.7 TIFR0 – Timer/Counter 0 Interrupt Flag Register
Bit
7
6
5
4
3
2
1
0
0x38 (0x58)
–
–
–
–
–
OCF0B
OCF0A
TOV0
Read/Write
R
R
R
R
R
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TIFR0
• Bits 7..3 – Res: Reserved Bits
These bits are reserved bits in the Atmel ATtiny24/44/84 and will always read as zero.
• Bit 2– OCF0B: Output Compare Flag 0 B
The OCF0B bit is set when a compare match occurs between the Timer/Counter 0 and the data in OCR0B, the output
compare register 0 B. OCF0B is cleared by hardware when executing the corresponding interrupt handling vector.
Alternatively, OCF0B is cleared by writing a logical one to the flag. When the I-bit in SREG, OCIE0B (Timer/Counter
compare b match interrupt enable), and OCF0B are set, the Timer/Counter compare match interrupt is executed.
• Bit 1– OCF0A: Output Compare Flag 0 A
The OCF0A bit is set when a compare match occurs between the Timer/Counter 0 and the data in OCR0A, the output
compare register 0 A. OCF0A is cleared by hardware when executing the corresponding interrupt handling vector.
Alternatively, OCF0A is cleared by writing a logical one to the flag. When the I-bit in SREG, OCIE0A (Timer/Counter 0
compare match interrupt enable), and OCF0A are set, the Timer/Counter 0 compare match interrupt is executed.
• Bit 0– TOV0: Timer/Counter0 Overflow Flag
The bit TOV0 is set when an overflow occurs in Timer/Counter 0. TOV0 is cleared by hardware when executing the
corresponding interrupt handling vector. Alternatively, TOV0 is cleared by writing a logical one to the flag. When the SREG Ibit, TOIE0 (Timer/Counter 0 overflow interrupt enable), and TOV0 are set, the Timer/Counter 0 overflow interrupt is
executed.
The setting of this flag is dependent of the WGM02:0 bit setting. See Table 13-8 on page 75 and Section 13-8 “Waveform
Generation Mode Bit Description” on page 75.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
77
14.
16-bit Timer/Counter1
14.1
Features
●
●
●
●
●
●
●
●
●
●
●
14.2
True 16-bit design (i.e., Allows 16-bit PWM)
Two independent output compare units
Double buffered output compare registers
One input capture unit
Input capture noise canceler
Clear timer on compare match (auto reload)
Glitch-free, phase correct pulse width modulator (PWM)
Variable PWM period
Frequency generator
External event counter
Four independent interrupt sources (TOV1, OCF1A, OCF1B, and ICF1)
Overview
The 16-bit Timer/Counter unit allows accurate program execution timing (event management), wave generation, and signal
timing measurement.
Most register and bit references in this section are written in general form. A lower case “n” replaces the Timer/Counter
number, and a lower case “x” replaces the output compare unit channel. However, when using the register or bit defines in a
program, the precise form must be used, i.e., TCNT1 for accessing Timer/Counter1 counter value and so on.
A simplified block diagram of the 16-bit Timer/Counter is shown in Figure 14-1 on page 79. For the actual placement of I/O
pins, refer to Section 1-1 “Pinout Atmel ATtiny24/44/84” on page 3. CPU accessible I/O registers, including I/O bits and I/O
pins, are shown in bold. The device-specific I/O register and bit locations are listed in the Section 14.11 “Register
Description” on page 97.
78
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Figure 14-1. 16-bit Timer/Counter Block Diagram(1)
TOVn (Int. Req.)
Count
Clear
Direction
Clock Select
Control Logic
clkTn
TOP
BOTTOM
=
=
Edge
Detector
Tn
(from Prescaler)
Timer/Counter
TCNTn
0
OCnA (Int. Req.)
Waveform
Generation
=
OCnA
DATA BUS
OCRnA
Fixed
TOP
Values
OCnB (Int. Req.)
Waveform
Generation
=
OCRnB
OCnB
(From Analog
Comparator Output)
ICFn (Int. Req.)
Edge
Detector
ICRn
TCCRnA
Note:
1.
Noise
Canceler
ICPn
TCCRnB
See Figure 1-1 on page 3 for Timer/Counter1 pin placement and description.
14.2.1 Registers
The Timer/Counter (TCNT1), output compare registers (OCR1A/B), and input capture register (ICR1) are all 16-bit registers.
Special procedures must be followed when accessing the 16-bit registers. These procedures are described in the Section
14.3 “Accessing 16-bit Registers” on page 80. The Timer/Counter control registers (TCCR1A/B) are 8-bit registers, and have
no CPU access restrictions. Interrupt request (abbreviated to Int.Req. in the figure) signals are all visible in the timer interrupt
flag register (TIFR). All interrupts are individually masked with the timer interrupt mask register (TIMSK). TIFR and TIMSK
are not shown in the figure.
The Timer/Counter can be clocked internally, via the prescaler, or by an external clock source on the T1 pin. The clock select
logic block controls which clock source and edge the Timer/Counter uses to increment (or decrement) its value. The
Timer/Counter is inactive when no clock source is selected. The output from the clock select logic is referred to as the timer
clock (clkT1).
The double buffered output compare registers (OCR1A/B) are compared with the Timer/Counter value at all times. The
result of the compare can be used by the waveform generator to generate a PWM or variable frequency output on the output
compare pin (OC1A/B). See Section 14.7 “Output Compare Units” on page 86. The compare match event will also set the
compare match flag (OCF1A/B) which can be used to generate an output compare interrupt request.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
79
The input capture register can capture the Timer/Counter value at a given external (edge-triggered) event on either the input
capture pin (ICP1) or on the analog comparator pins (see Section 17. “Analog Comparator” on page 115). The input capture
unit includes a digital filtering unit (noise canceller) for reducing the chance of capturing noise spikes.
The top value, or maximum Timer/Counter value, can in some modes of operation be defined by either the OCR1A register,
the ICR1 register, or by a set of fixed values. When using OCR1A as top value in a PWM mode, the OCR1A register cannot
be used for generating a PWM output. However, the top value will in this case be double buffered, allowing the top value to
be changed at run time. If a fixed top value is required, the ICR1 register can be used as an alternative, freeing the OCR1A
to be used as PWM output.
14.2.2 Definitions
The following definitions are used extensively throughout the section:
Table 14-1. Definitions
Parameter
Definition
BOTTOM
The counter reaches the BOTTOM when it becomes 0x0000.
MAX
The counter reaches its MAXimum when it becomes 0xFFFF (decimal 65535).
TOP
The counter reaches the TOP when it becomes equal to the highest value in the count sequence. The top
value can be assigned to be one of the fixed values: 0x00FF, 0x01FF, or 0x03FF, or to the value stored in
the OCR1A or ICR1 register. The assignment is dependent on the mode of operation.
14.2.3 Compatibility
The 16-bit Timer/Counter has been updated and improved from previous versions of the 16-bit Atmel® AVR® Timer/Counter.
This 16-bit Timer/Counter is fully compatible with the earlier version regarding:
● All 16-bit Timer/Counter related I/O register address locations, including timer interrupt registers.
●
●
Bit locations inside all 16-bit Timer/Counter registers, including timer interrupt registers.
Interrupt vectors.
The following control bits have changed name, but have same functionality and register location:
● PWM10 is changed to WGM10.
●
●
PWM11 is changed to WGM11.
CTC1 is changed to WGM12.
The following bits are added to the 16-bit Timer/Counter control registers:
● 1A and 1B are added to TCCR1A.
●
WGM13 is added to TCCR1B.
The 16-bit Timer/Counter has improvements that will affect the compatibility in some special cases.
14.3
Accessing 16-bit Registers
TCNT1, OCR1A/B, and ICR1 are 16-bit registers that can be accessed by the Atmel AVR CPU via the 8-bit data bus. The
16-bit registers must be byte accessed using two read or write operations. Each 16-bit timer has a single 8-bit register for
temporary storage of the high byte of the 16-bit access. The same temporary register is shared between all 16-bit registers
within each 16-bit timer. Accessing the low byte triggers the 16-bit read or write operation. When the low byte of a 16-bit
register is written by the CPU, the high byte stored in the temporary register and the low byte written are both copied into the
16-bit register in the same clock cycle. When the low byte of a 16-bit register is read by the CPU, the high byte of the 16-bit
register is copied into the temporary register in the same clock cycle as the low byte is read.
Not all 16-bit accesses use the temporary register for the high byte. Reading the OCR1A/B 16-bit registers does not involve
using the temporary register.
To do a 16-bit write, the high byte must be written before the low byte. For a 16-bit read, the low byte must be read before the
high byte.
80
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
The following code examples show how to access the 16-bit timer registers, assuming that no interrupts updates the
temporary register. The same principle can be used directly for accessing the OCR1A/B and ICR1 registers. Note that when
using C, the compiler handles the 16-bit access.
Assembly Code Examples(1)
...
; Set TCNT1 to 0x01FF
ldi
r17,0x01
ldi
r16,0xFF
out
TCNT1H,r17
out
TCNT1L,r16
; Read TCNT1 into r17:r16
in
r16,TCNT1L
in
r17,TCNT1H
...
C Code Examples(1)
unsigned int i;
...
/* Set TCNT1 to 0x01FF */
TCNT1 = 0x1FF;
/* Read TCNT1 into i */
i = TCNT1;
...
Note:
1.
See Section 4. “About Code Examples” on page 8.
The assembly code example returns the TCNT1 value in the r17:r16 register pair.
It is important to notice that accessing 16-bit registers are atomic operations. If an interrupt occurs between the two
instructions accessing the 16-bit register and the interrupt code updates the temporary register by accessing the same or
any of the other 16-bit timer registers, then the result of the access outside the interrupt will be corrupted. Therefore, when
both the main code and the interrupt code update the temporary register, the main code must disable the interrupts during
the 16-bit access.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
81
The following code examples show how to do an atomic read of the TCNT1 register contents. Reading any of the OCR1A/B
or ICR1 registers can be done by using the same principle.
Assembly Code Example(1)
TIM16_ReadTCNT1:
; Save global interrupt flag
in
r18,SREG
; Disable interrupts
cli
; Read TCNT1 into r17:r16
in
r16,TCNT1L
in
r17,TCNT1H
; Restore global interrupt flag
out
SREG,r18
ret
C Code Example(1)
unsigned int TIM16_ReadTCNT1( void )
{
unsigned char sreg;
unsigned int i;
/* Save global interrupt flag */
sreg = SREG;
/* Disable interrupts */
_CLI();
/* Read TCNT1 into i */
i = TCNT1;
/* Restore global interrupt flag */
SREG = sreg;
return i;
}
Note:
1.
See Section 4. “About Code Examples” on page 8.
The assembly code example returns the TCNT1 value in the r17:r16 register pair.
82
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
The following code examples show how to do an atomic write of the TCNT1 Register contents. Writing any of the OCR1A/B
or ICR1 registers can be done by using the same principle.
Assembly Code Example(1)
TIM16_WriteTCNT1:
; Save global interrupt flag
in
r18,SREG
; Disable interrupts
cli
; Set TCNT1 to r17:r16
out
TCNT1H,r17
out
TCNT1L,r16
; Restore global interrupt flag
out
SREG,r18
ret
C Code Example(1)
void TIM16_WriteTCNT1( unsigned int i )
{
unsigned char sreg;
unsigned int i;
/* Save global interrupt flag */
sreg = SREG;
/* Disable interrupts */
_CLI();
/* Set TCNT1 to i */
TCNT1 = i;
/* Restore global interrupt flag */
SREG = sreg;
}
Note:
1.
See Section 4. “About Code Examples” on page 8.
The assembly code example requires that the r17:r16 register pair contains the value to be written to TCNT1.
14.3.1 Reusing the Temporary High Byte Register
If when writing to more than one 16-bit register the high byte is the same for all registers writ- ten, then the high byte only
needs to be written once. However, note that the same rule of atomic operation described previously also applies in this
case.
14.4
Timer/Counter Clock Sources
The Timer/Counter can be clocked by an internal or an external clock source. The clock source is selected by the clock
select logic which is controlled by the clock select (CS12:0) bits located in the Timer/Counter control register B (TCCR1B).
For details on clock sources and prescaler, see Section 15. “Timer/Counter Prescaler” on page 103.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
83
14.5
Counter Unit
The main part of the 16-bit Timer/Counter is the programmable 16-bit bi-directional counter unit. Figure 14-2 shows a block
diagram of the counter and its surroundings.
Figure 14-2. Counter Unit Block Diagram
DATA BUS
(8-bit)
TOVn
(Int. Req.)
TEMP (8-bit)
Clock Select
Count
TCNTnH (8-bit)
TCNTnL (8-bit)
TCNTn (16-bit Counter)
Clear
Control Logic
clkTn
Edge
Detector
Tn
Direction
(from Prescaler)
TOP
BOTTOM
Signal description (internal signals):
Count
Increment or decrement TCNT1 by 1.
Direction
Select between increment and decrement.
Clear
Clear TCNT1 (set all bits to zero).
clkT1
Timer/Counter clock.
TOP
Signal that TCNT1 has reached maximum value.
BOTTOM
Signal that TCNT1 has reached minimum value (zero).
The 16-bit counter is mapped into two 8-bit I/O memory locations: counter high (TCNT1H) containing the upper eight bits
of the counter, and counter low (TCNT1L) containing the lower eight bits. The TCNT1H register can only be indirectly
accessed by the CPU. When the CPU does an access to the TCNT1H I/O location, the CPU accesses the high byte
temporary register (TEMP). The temporary register is updated with the TCNT1H value when TCNT1L is read, and
TCNT1H is updated with the temporary register value when TCNT1L is written. This allows the CPU to read or write the
entire 16-bit counter value within one clock cycle via the 8-bit data bus. It is important to notice that there are special
cases of writing to the TCNT1 register when the counter is counting that will give unpredictable results. The special cases
are described in the sections where they are of importance.
Depending on the mode of operation used, the counter is cleared, incremented, or decremented at each timer clock
(clkT1). The clkT1 can be generated from an external or internal clock source, selected by the clock select bits (CS12:0).
When no clock source is selected (CS12:0 = 0,) the timer is stopped. However, the TCNT1 value can be accessed by the
CPU independently of whether clkT1 is present or not. A CPU write overrides (has priority over) all counter clear or count
operations.
The counting sequence is determined by the setting of the waveform generation mode bits (WGM13:0) located in
Timer/Counter control registers A and B (TCCR1A and TCCR1B). There are close connections between how the counter
behaves (counts) and how waveforms are generated on the output compare outputs (OC1x). For more details about
advanced counting sequences and waveform generation, see Section 14.9 “Modes of Operation” on page 89.
The Timer/Counter overflow flag (TOV1) is set according to the mode of operation selected by the WGM13:0 bits. TOV1 can
be used for generating a CPU interrupt.
14.6
Input Capture Unit
The Timer/Counter incorporates an input capture unit that can capture external events and give them a time stamp indicating
time of occurrence. The external signal indicating an event, or multiple events, can be applied via the ICP1 pin or,
alternatively, via the analog comparator unit. The time stamps can then be used to calculate frequency, duty cycle, and other
features of the signal applied. Alternatively, the time stamps can be used for creating a log of the events.
The input capture unit is illustrated by the block diagram shown in Figure 14-3 on page 85. The elements of the block
diagram that are not directly a part of the input capture unit are shaded gray. The small “n” in register and bit names
indicates the Timer/Counter number.
84
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Figure 14-3. Input Capture Unit Block Diagram
DATA BUS (8-bit)
TEMP (8-bit)
ICRnH (8-bit)
ICRnL (8-bit)
TCNTnH (8-bit)
ICRn (16-bit Register)
WRITE
+
-
ACO*
Analog
Comparator
TCNTnL (8-bit)
TCNTn (16-bit Counter)
ACIC*
ICNC
ICES
Noise
Canceler
Edge
Detector
ICFn (Int. Req.)
ICPn
When a change of the logic level (an event) occurs on the input capture pin (ICP1), or alternatively on the analog comparator
output (ACO), and this change conforms to the setting of the edge detector, a capture will be triggered. When a capture is
triggered, the 16-bit value of the counter (TCNT1) is written to the input capture register (ICR1). The input capture flag (ICF1)
is set at the same system clock as the TCNT1 value is copied into ICR1 register. If enabled (ICIE1 = 1), the input capture flag
generates an input capture interrupt. The ICF1 flag is automatically cleared when the interrupt is executed. Alternatively, the
ICF1 flag can be cleared by software by writing a logical one to its I/O bit location.
Reading the 16-bit value in the input capture register (ICR1) is done by first reading the low byte (ICR1L) and then the high
byte (ICR1H). When the low byte is read, the high byte is copied into the high byte temporary register (TEMP). When the
CPU reads the ICR1H I/O location, it will access the TEMP register.
The ICR1 register can only be written when using a waveform generation mode that utilizes the ICR1 register for defining the
counter's top value. In these cases the waveform generation mode (WGM13:0) bits must be set before the top value can be
written to the ICR1 register. When writing the ICR1 register, the high byte must be written to the ICR1H I/O location before
the low byte is written to ICR1L.
For more information on how to access the 16-bit registers refer to Section 14.3 “Accessing 16-bit Registers” on page 80.
14.6.1 Input Capture Trigger Source
The main trigger source for the input capture unit is the input capture pin (ICP1). Timer/Counter 1 can alternatively use the
analog comparator output as trigger source for the input capture unit. The analog comparator is selected as trigger source by
setting the analog comparator input capture (ACIC) bit in the analog comparator control and status register (ACSR). Be
aware that changing the trigger source can trigger a capture. The input capture flag must, therefore, be cleared after the
change.
Both the input capture pin (ICP1) and the analog comparator output (ACO) are sampled using the same technique as for the
T1 pin (Figure 15-1 on page 103). The edge detector is also identical. However, when the noise canceller is enabled,
additional logic is inserted before the edge detector, which increases the delay by four system clock cycles. Note that the
inputs of the noise canceller and edge detector are always enabled unless the Timer/Counter is set in a waveform
generation mode that uses ICR1 to define top.
An input capture can be triggered by software by controlling the port of the ICP1 pin.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
85
14.6.2 Noise Canceller
The noise canceller improves noise immunity by using a simple digital filtering scheme. The noise canceller input is
monitored over four samples, and all four must be equal to change the output, which in turn is used by the edge detector.
The noise canceller is enabled by setting the input capture noise canceller (ICNC1) bit in Timer/Counter control register B
(TCCR1B). When enabled, the noise canceller introduces an additional four system clock cycles of delay between a change
applied to the input and the update of the ICR1 register. The noise canceller uses the system clock, and is, therefore, not
affected by the prescaler.
14.6.3 Using the Input Capture Unit
The main challenge when using the input capture unit is to assign enough processor capacity for handling the incoming
events. The time between two events is critical. If the processor has not read the captured value in the ICR1 register before
the next event occurs, the ICR1 will be overwritten with a new value. In this case the result of the capture will be incorrect.
When using the input capture interrupt, the ICR1 register should be read as early in the interrupt handler routine as possible.
Even though the input capture interrupt has relatively high priority, the maximum interrupt response time is dependent on the
maximum number of clock cycles it takes to handle any of the other interrupt requests.
Using the input capture unit in any mode of operation when the top value (resolution) is actively changed during operation is
not recommended.
Measurement of an external signal's duty cycle requires that the trigger edge be changed after each capture. Changing the
edge sensing must be done as early as possible after the ICR1 register has been read. After a change of the edge, the input
capture flag (ICF1) must be cleared by software (writing a logical one to the I/O bit location). For measuring frequency only,
the clearing of the ICF1 flag is not required (if an interrupt handler is used).
14.7
Output Compare Units
The 16-bit comparator continuously compares TCNT1 with the output compare register (OCR1x). If TCNT equals OCR1x,
the comparator signals a match. A match will set the output compare flag (OCF1x) at the next timer clock cycle. If enabled
(OCIE1x = 1), the output compare flag generates an output compare interrupt. The OCF1x flag is automatically cleared
when the interrupt is executed. Alternatively the OCF1x flag can be cleared by software by writing a logical one to its I/O bit
location. The waveform generator uses the match signal to generate an output according to the operating mode set by the
waveform generation mode (WGM13:0) bits and compare output mode (COM1x1:0) bits. The top and bottom signals are
used by the waveform generator for handling the special cases of the extreme values in some modes of operation (Section
14.9 “Modes of Operation” on page 89).
A special feature of output compare unit A allows it to define the Timer/Counter TOP value (i.e., counter resolution). In
addition to the counter resolution, the TOP value defines the period time for waveforms generated by the waveform
generator.
Figure 14-4 on page 87 shows a block diagram of the output compare unit. The small “n” in the register and bit names
indicates the device number (n = 1 for Timer/Counter 1), and the “x” indicates output compare unit (A/B). The elements of the
block diagram that are not directly a part of the output compare unit are shaded gray.
86
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Figure 14-4. Output Compare Unit, Block Diagram
DATA BUS (8-bit)
TEMP (8-bit)
OCRnxH Buf. (8-bit)
OCRnxL Buf. (8-bit)
TCNTnH (8-bit)
OCRnx Buffer (16-bit Register)
OCRnxH (8-bit)
TCNTnL (8-bit)
TCNTn (16-bit Counter)
OCRnxL (8-bit)
OCRnx (16-bit Register)
=
(16-bit Comparator)
OCFnx (Int. Req.)
TOP
Waveform Generator
OCnx
BOTTOM
WGMn3:0
COMnx1:0
The OCR1x register is double buffered when using any of the twelve pulse width modulation (PWM) modes. For the normal
and clear timer on compare (CTC) modes of operation, the double buffering is disabled. The double buffering synchronizes
the update of the OCR1x compare register to either top or bottom of the counting sequence. The synchronization prevents
the occurrence of odd-length, non-symmetrical PWM pulses, thereby making the output glitch-free.
The OCR1x register access may seem complex, but this is not the case. When the double buffering is enabled, the CPU has
access to the OCR1x buffer register, and if double buffering is disabled the CPU will access the OCR1x directly. The content
of the OCR1x (buffer or compare) register is changed only by a write operation (the Timer/Counter does not update this
register automatically as it does for the TCNT1 and ICR1 registers). Therefore, OCR1x is not read via the high byte
temporary register (TEMP). However, it is a good practice to read the low byte first, as when accessing other 16-bit registers.
Writing the OCR1x registers must be done via the TEMP register because the compare of all 16 bits is done continuously.
The high byte (OCR1xH) has to be written first. When the high byte I/O location is written by the CPU, the TEMP register will
be updated by the value written. Then when the low byte (OCR1xL) is written to the lower eight bits, the high byte will be
copied into the upper 8-bits of either the OCR1x buffer or the OCR1x compare register in the same system clock cycle.
For more information of how to access the 16-bit registers, refer to Section 14.3 “Accessing 16-bit Registers” on page 80.
14.7.1 Force Output Compare
In non-PWM waveform generation modes, the match output of the comparator can be forced by writing a logical one to the
force output compare (1x) bit. Forcing compare match will not set the OCF1x flag or reload/clear the timer, but the OC1x pin
will be updated as if a real compare match had occurred (the COM11:0 bit settings define whether the OC1x pin is set,
cleared or toggled).
14.7.2 Compare Match Blocking by TCNT1 Write
All CPU writes to the TCNT1 register will block any compare match that occurs in the next timer clock cycle, even when the
timer is stopped. This feature allows OCR1x to be initialized to the same value as TCNT1 without triggering an interrupt
when the Timer/Counter clock is enabled.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
87
14.7.3 Using the Output Compare Unit
Because writing TCNT1 in any mode of operation will block all compare matches for one timer clock cycle, there are risks
involved in changing TCNT1 when using any of the output compare channels, independent of whether the Timer/Counter is
running or not. If the value written to TCNT1 equals the OCR1x value, the compare match will be missed, resulting in
incorrect waveform generation. Do not write the TCNT1 equal to top in PWM modes with variable top values. The compare
match for the top will be ignored, and the counter will continue to 0xFFFF. Similarly, do not write the TCNT1 value equal to
bottom when the counter is down-counting.
The setup of the OC1x should be performed before setting the data direction register for the port pin to output. The easiest
way of setting the OC1x value is to use the force output compare (1x) strobe bits in normal mode. The OC1x register keeps
its value even when changing between waveform generation modes.
Be aware that the COM1x1:0 bits are not double buffered together with the compare value. Changing the COM1x1:0 bits will
take effect immediately.
14.8
Compare Match Output Unit
The compare output mode (COM1x1:0) bits have two functions. The waveform generator uses the COM1x1:0 bits for
defining the output compare (OC1x) state at the next compare match. Secondly the COM1x1:0 bits control the OC1x pin
output source. Figure 14-5 shows a simplified schematic of the logic affected by the COM1x1:0 bit settings. The I/O
registers, I/O bits, and I/O pins in the figure are shown in bold. Only the parts of the general I/O port control registers (DDR
and PORT) that are affected by the COM1x1:0 bits are shown. When referring to the OC1x state, the reference is for the
internal OC1x register, not the OC1x pin. If a system reset occurs, the OC1x register is reset to “0”.
Figure 14-5. Compare Match Output Unit, Schematic
COMnx1
COMnx0
FOCn
Waveform
Generator
D
Q
1
OCnx
Pin
OCnx
0
DATA BUS
D
Q
PORT
D
Q
DDR
clkI/O
The general I/O port function is overridden by the output compare (OC1x) from the waveform generator if either of the
COM1x1:0 bits are set. However, the OC1x pin direction (input or output) is still controlled by the data direction register
(DDR) for the port pin. The data direction register bit for the OC1x pin (DDR_OC1x) must be set as output before the OC1x
value is visible on the pin. The port override function is generally independent of the waveform generation mode, but there
are some exceptions. See Table 14-2 on page 97, Table 14-3 on page 97 and Table 14-4 on page 98 for details.
The design of the output compare pin logic allows initialization of the OC1x state before the output is enabled. Note that
some COM1x1:0 bit settings are reserved for certain modes of operation.
See Section 14.11 “Register Description” on page 97.
The COM1x1:0 bits have no effect on the input capture unit.
88
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
14.8.1 Compare Output Mode and Waveform Generation
The waveform generator uses the COM1x1:0 bits differently in normal, CTC, and PWM modes. For all modes, setting the
COM1x1:0 = 0 tells the waveform generator that no action on the OC1x register is to be performed on the next compare
match. For compare output actions in the non-PWM modes refer to Table 14-2 on page 97. For fast PWM mode refer to
Table 14-3 on page 97, and for phase correct and phase and frequency correct PWM refer to Table 14-4 on page 98.
A change of the COM1x1:0 bit states will have an effect at the first compare match after the bits are written. For non-PWM
modes, the action can be forced to have immediate effect by using the 1x strobe bits.
14.9
Modes of Operation
The mode of operation, i.e., the behavior of the Timer/Counter and the output compare pins, is defined by the combination of
the waveform generation mode (WGM13:0) and compare output mode (COM1x1:0) bits. The compare output mode bits do
not affect the counting sequence, while the waveform generation mode bits do. The COM1x1:0 bits control whether the
PWM output generated should be inverted or not (inverted or non-inverted PWM). For non-PWM modes, the COM1x1:0 bits
control whether the output should be set, cleared or toggle at a compare match (Section 14.8 “Compare Match Output Unit”
on page 88). For detailed timing information refer to Section 14.10 “Timer/Counter Timing Diagrams” on page 95.
14.9.1 Normal Mode
The simplest mode of operation is the normal mode (WGM13:0 = 0). In this mode the counting direction is always up
(incrementing), and no counter clear is performed. The counter simply overruns when it passes its maximum 16-bit value
(max = 0xFFFF), and then restarts from the bottom (0x0000). In normal operation, the Timer/Counter overflow flag (TOV1)
will be set on the same timer clock cycle on which the TCNT1 becomes zero. The TOV1 flag in this case behaves like a 17th
bit, except that it is only set, not cleared. However, when combined with the timer overflow interrupt that automatically clears
the TOV1 flag, the timer resolution can be increased by software. There are no special cases to consider in the normal
mode. A new counter value can be written anytime.
The input capture unit is easy to use in normal mode. However, observe that the maximum interval between the external
events must not exceed the resolution of the counter. If the interval between events is too long, the timer overflow interrupt or
the prescaler must be used to extend the resolution for the capture unit.
The output compare units can be used to generate interrupts at some given time. Using the output compare to generate
waveforms in normal mode is not recommended because this will occupy too much CPU time.
14.9.2 Clear Timer on Compare Match (CTC) Mode
In clear timer on compare, or CTC, mode (WGM13:0 = 4 or 12), the OCR1A or ICR1 register is used to manipulate the
counter resolution. In CTC mode, the counter is cleared to zero when the counter value (TCNT1) matches either OCR1A
(WGM13:0 = 4) or ICR1 (WGM13:0 = 12). OCR1A or ICR1 define the top value for the counter, and hence also its resolution.
This mode allows greater control of the compare match output frequency. It also simplifies the operation of counting external
events.
The timing diagram for the CTC mode is shown in Figure 14-6. The counter value (TCNT1) increases until a compare match
occurs with either OCR1A or ICR1, and then counter (TCNT1) is cleared.
Figure 14-6. CTC Mode, Timing Diagram
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
TCNTn
OCnA
(Toggle)
Period
(COMnA1:0 = 1)
1
2
3
4
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
89
An interrupt can be generated each time the counter value reaches the top value by either using the OCF1A or ICF1 flag
according to the register used to define the top value. If the interrupt is enabled, the interrupt handler routine can be used for
updating the top value. However, changing the top to a value close to bottom when the counter is running with no or a low
prescaler value must be done with care because the CTC mode does not have the double buffering feature. If the new value
written to OCR1A or ICR1 is lower than the current value of TCNT1, the counter will miss the compare match. The counter
will then have to count to its maximum value (0xFFFF) and wrap around starting at 0x0000 before the compare match can
occur. In many cases this feature is not desirable. An alternative will then be to use the fast PWM mode, using OCR1A for
defining top (WGM13:0 = 15) because OCR1A then will be double buffered.
For generating a waveform output in CTC mode, the OC1A output can be set to toggle its logical level on each compare
match by setting the compare output mode bits to toggle mode (COM1A1:0 = 1). The OC1A value will not be visible on the
port pin unless the data direction for the pin is set to output (DDR_OC1A = 1). The waveform generated will have a
maximum frequency of 1A = fclk_I/O/2 when OCR1A is set to zero (0x0000). The waveform frequency is defined by the
following equation:
f clk_I/O
f OCnA = ----------------------------------------------------2  N   1 + OCRnA 
The variable N represents the prescaler factor (1, 8, 64, 256, or 1024).
As for the normal mode of operation, the TOV1 flag is set on the same timer clock cycle on which the counter counts from
max to 0x0000.
14.9.3 Fast PWM Mode
The fast pulse width modulation, or fast PWM, mode (WGM13:0 = 5, 6, 7, 14, or 15) provides a high-frequency PWM
waveform generation option. The fast PWM differs from the other PWM options by its single-slope operation. The counter
counts from bottom to top then restarts from bottom.
In non-inverting compare output mode, the output compare (OC1x) is cleared on the compare match between TCNT1 and
OCR1x, and set at bottom. In inverting compare output mode, output is set on compare match and cleared at bottom.
Due to the single-slope operation, the operating frequency of the fast PWM mode can be twice as high as the phase correct
and phase and frequency correct PWM modes that use dual-slope operation. This high frequency makes the fast PWM
mode well suited for power regulation, rectification, and DAC applications. High frequency allows the use of physically
smaller external components (coils, capacitors, etc.), and hence reduces total system cost.
The PWM resolution for fast PWM can be fixed to 8, 9, or 10 bits, or defined by either ICR1 or OCR1A. The minimum
resolution allowed is 2 bits (ICR1 or OCR1A set to 0x0003), and the maximum resolution is 16 bits (ICR1 or OCR1A set to
MAX). The PWM resolution in bits can be calculated by using the following equation:
:
log  TOP + 1 
R FPWM = --------------------------------log  2 
In fast PWM mode the counter is incremented until the counter value matches either one of the fixed values 0x00FF,
0x01FF, or 0x03FF (WGM13:0 = 5, 6, or 7), the value in ICR1 (WGM13:0 = 14), or the value in OCR1A (WGM13:0 = 15).
The counter is then cleared at the following timer clock cycle. The timing diagram for the fast PWM mode is shown in Figure
14-7 on page 91. The figure shows fast PWM mode when OCR1A or ICR1 is used to define top. The TCNT1 value in the
timing diagram is shown as a histogram for illustrating the single-slope operation. The diagram includes non-inverted and
inverted PWM outputs. The small horizontal lines on the TCNT1 slopes represent compare matches between OCR1x and
TCNT1. The OC1x interrupt flag will be set when a compare match occurs.
90
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Figure 14-7. Fast PWM Mode, Timing Diagram
OCRnx/ TOP Update and
TOVn Interrupt Flag Set and
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
TCNTn
OCnx
(COMnx1:0 = 2)
OCnx
(COMnx1:0 = 3)
Period
1
2
3
4
5
6
7
8
The Timer/Counter overflow flag (TOV1) is set each time the counter reaches top. In addition, the OC1A or ICF1 flag is set
on the same timer clock cycle on which TOV1 is set when either OCR1A or ICR1 is used for defining the top value. If one of
the interrupts are enabled, the interrupt handler routine can be used for updating the top and compare values.
When changing the top value, the program must ensure that the new top value is higher or equal to the value of all of the
compare registers. If the top value is lower than any of the compare registers, a compare match will never occur between
TCNT1 and OCR1x. Note that when using fixed top values, the unused bits are masked to zero when any of the OCR1x
registers are written
The procedure for updating ICR1 differs from that for updating OCR1A when used for defining the top value. The ICR1
register is not double buffered. This means that if ICR1 is changed to a low value when the counter is running with no or a
low prescaler value, there is a risk that the new ICR1 value written is lower than the current value of TCNT1. The result will
then be that the counter will miss the compare match at the top value. The counter will then have to count to the max value
(0xFFFF) and wrap around starting at 0x0000 before the compare match can occur. The OCR1A register, however, is
double buffered. This feature allows the OCR1A I/O location to be written anytime. When the OCR1A I/O location is written,
the value written will be put into the OCR1A buffer register. The OCR1A compare register will then be updated with the value
in the buffer register at the next timer clock cycle when TCNT1 matches top. The update is done on the same timer clock
cycle on which TCNT1 is cleared and the TOV1 flag is set.
Using the ICR1 register for defining top works well when using fixed top values. By using ICR1, the OCR1A register is free to
be used for generating a PWM output on OC1A. How- ever, if the base PWM frequency is actively changed (by changing the
top value), using the OCR1A as top is clearly a better choice due to its double buffer feature.
In fast PWM mode, the compare units allow generation of PWM waveforms on the OC1x pins. Setting the COM1x1:0 bits to
two will produce a non-inverted PWM, and an inverted PWM out- put can be generated by setting the COM1x1:0 to three
(see Table 14-3 on page 97). The actual OC1x value will only be visible on the port pin if the data direction for the port pin is
set as output (DDR_OC1x). The PWM waveform is generated by setting (or clearing) the OC1x register at the compare
match between OCR1x and TCNT1, and clearing (or setting) the OC1x register on the timer clock cycle on which the counter
is cleared (changes from top to bottom). The PWM frequency for the output can be calculated by the following equation:
f clk_I/O
f OCnxPWM = -----------------------------------N   1 + TOP 
The variable N represents the prescaler divider (1, 8, 64, 256, or 1024). The extreme values for the OCR1x register
represent special cases when generating a PWM waveform output in the fast PWM mode. If the OCR1x is set equal to
bottom (0x0000), the output will be a narrow spike for each top+1 timer clock cycle. Setting OCR1x equal to top will result in
a constant high or low output (depending on the polarity of the output set by the COM1x1:0 bits.) A frequency waveform
output (with 50% duty cycle) in fast PWM mode can be achieved by setting OC1A to toggle its logical level on each compare
match (COM1A1:0 = 1). The waveform generated will have a maximum frequency of 1A = fclk_I/O/2 when OCR1A is set to zero
(0x0000). This feature is similar to the OC1A toggle in CTC mode, except the double buffer feature of the output compare
unit is enabled in the fast PWM mode.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
91
14.9.4 Phase Correct PWM Mode
The phase correct pulse width modulation, or phase correct PWM, mode (WGM13:0 = 1, 2, 3, 10, or 11) provides a
high-resolution phase correct PWM waveform generation option. The phase correct PWM mode is, like the phase and
frequency correct PWM mode, based on a dual-slope operation. The counter counts repeatedly from bottom (0x0000) to top
and then from top to bottom.
In non-inverting compare output mode, the output compare (OC1x) is cleared on the compare match between TCNT1 and
OCR1x while up-counting, and set on the compare match while down-counting. In inverting output compare mode, the
operation is inverted. The dual-slope operation has lower maximum operation frequency than single-slope operation.
However, due to the symmetric feature of the dual-slope PWM modes, these modes are preferred for motor control
applications.
The PWM resolution for the phase correct PWM mode can be fixed to 8, 9, or 10 bits, or defined by either ICR1 or OCR1A.
The minimum resolution allowed is 2 bits (ICR1 or OCR1A set to 0x0003), and the maximum resolution is 16 bits (ICR1 or
OCR1A set to max). The PWM resolution in bits can be calculated by using the following equation:
log  TOP + 1 
R PCPWM = --------------------------------log  2 
In phase correct PWM mode, the counter is incremented until the counter value matches either one of the fixed values
0x00FF, 0x01FF, or 0x03FF (WGM13:0 = 1, 2, or 3), the value in ICR1 (WGM13:0 = 10), or the value in OCR1A
(WGM13:0 = 11). The counter has then reached the top, and changes the count direction. The TCNT1 value will be equal to
top for one timer clock cycle. The timing diagram for the phase correct PWM mode is shown on Figure 14-8. The figure
shows phase correct PWM mode when OCR1A or ICR1 is used to define top. The TCNT1 value in the timing diagram is
shown as a histogram for illustrating the dual-slope operation. The diagram includes non-inverted and inverted PWM
outputs. The small horizontal lines on the TCNT1 slopes represent compare matches between OCR1x and TCNT1. The
OC1x interrupt flag will be set when a compare match occurs.
Figure 14-8. Phase Correct PWM Mode, Timing Diagram
OCRnx/ TOP Update and
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
TOVn Interrupt Flag Set
(Interrupt on Bottom)
TCNTn
OCnx
(COMnx1:0 = 2)
OCnx
(COMnx1:0 = 3)
Period
1
2
3
4
The Timer/Counter overflow flag (TOV1) is set each time the counter reaches bottom. When either OCR1A or ICR1 is used
for defining the TOP value, the OC1A or ICF1 flag is set accordingly on the same timer clock cycle on which the OCR1x
registers are updated with the double buffer value (at top). The interrupt flags can be used to generate an interrupt each time
the counter reaches the top or bottom value.
92
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
When changing the top value, the program must ensure that the new top value is higher or equal to the value of all of the
compare registers. If the top value is lower than any of the compare registers, a compare match will never occur between
TCNT1 and OCR1x. Note that when using fixed top values, the unused bits are masked to zero when any of the OCR1x
registers are written. As the third period shown in Figure 14-8 on page 92 illustrates, changing the top actively while the
Timer/Counter is running in the phase correct mode can result in an asymmetrical output. The reason for this can be found in
the time of update of the OCR1x register. Since the OCR1x update occurs at top, the PWM period starts and ends at top.
This implies that the length of the falling slope is determined by the previous top value, while the length of the rising slope is
determined by the new top value. When these two values differ, the two slopes of the period will differ in length. The
difference in length gives the asymmetrical result on the output.
It is recommended to use the phase and frequency correct mode instead of the phase correct mode when changing the top
value while the Timer/Counter is running. When using a static top value, there are practically no differences between the two
modes of operation.
In phase correct PWM mode, the compare units allow generation of PWM waveforms on the OC1x pins. Setting the
COM1x1:0 bits to two will produce a non-inverted PWM, and an inverted PWM output can be generated by setting the
COM1x1:0 to three (See Table 14-4 on page 98). The actual OC1x value will only be visible on the port pin if the data
direction for the port pin is set as output (DDR_OC1x). The PWM waveform is generated by setting (or clearing) the OC1x
register at the compare match between OCR1x and TCNT1 when the counter increments, and clearing (or setting) the OC1x
register at compare match between OCR1x and TCNT1 when the counter decrements. The PWM frequency for the output
when using phase correct PWM can be calculated by the following equation:
f clk_I/O
f OCnxPCPWM = ------------------------------2  N  TOP
The variable N represents the prescaler divider (1, 8, 64, 256, or 1024).
The extreme values for the OCR1x register represent special cases when generating a PWM waveform output in the phase
correct PWM mode. If the OCR1x is set equal to bottom, the output will be continuously low, and if set equal to top, the
output will be continuously high for non-inverted PWM mode. For inverted PWM the output will have the opposite logic
values.
14.9.5 Phase and Frequency Correct PWM Mode
The phase and frequency correct pulse width modulation, or phase and frequency correct PWM, mode (WGM13:0 = 8 or 9)
provides a high-resolution phase and frequency correct PWM waveform generation option. The phase and frequency correct
PWM mode is, like the phase correct PWM mode, based on a dual-slope operation. The counter counts repeatedly from
bottom (0x0000) to top and then from top to bottom. In non-inverting compare output mode, the output compare (OC1x) is
cleared on the compare match between TCNT1 and OCR1x while up-counting, and set on the compare match while down
counting.
In inverting compare output mode, the operation is inverted. The dual-slope operation gives a lower maximum operation
frequency compared to the single-slope operation. However, due to the symmetric feature of the dual-slope PWM modes,
these modes are preferred for motor control applications.
The main difference between the phase correct, and the phase and frequency correct PWM mode is the time the OCR1x
register is updated by the OCR1x buffer register (see Figure 14-8 on page 92 and Figure 14-9 on page 94).
The PWM resolution for the phase and frequency correct PWM mode can be defined by either ICR1 or OCR1A. The
minimum resolution allowed is 2 bits (ICR1 or OCR1A set to 0x0003), and the maximum resolution is 16 bits (ICR1 or
OCR1A set to max). The PWM resolution in bits can be calculated using the following equation:
log  TOP + 1 
R PFCPWM = --------------------------------log  2 
In phase and frequency correct PWM mode, the counter is incremented until the counter value matches either the value in
ICR1 (WGM13:0 = 8), or the value in OCR1A (WGM13:0 = 9). The counter has then reached the top, and changes the count
direction. The TCNT1 value will be equal to top for one timer clock cycle. The timing diagram for the phase and frequency
correct PWM mode is shown on Figure 14-9 on page 94. The figure shows phase and frequency correct PWM mode when
OCR1A or ICR1 is used to define top. The TCNT1 value in the timing diagram is shown as a histogram for illustrating the
dual-slope operation. The diagram includes non-inverted and inverted PWM outputs. The small horizontal lines on the
TCNT1 slopes represent compare matches between OCR1x and TCNT1. The OC1x interrupt flag will be set when a
compare match occurs.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
93
Figure 14-9. Phase and Frequency Correct PWM Mode, Timing Diagram
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
OCRnx/ TOP Update and
TOVn Interrupt Flag Set
(Interrupt on Bottom)
TCNTn
OCnx
(COMnx1:0 = 2)
OCnx
(COMnx1:0 = 3)
Period
1
2
3
4
The Timer/Counter overflow flag (TOV1) is set on the same timer clock cycle on which the OCR1x registers are updated with
the double buffer value (at bottom). When either OCR1A or ICR1 is used for defining the top value, the OC1A or ICF1 flag is
set accordingly when TCNT1 has reached top. The interrupt flags can then be used to generate an interrupt each time the
counter reaches the top or bottom value.
When changing the top value, the program must ensure that the new top value is higher or equal to the value of all of the
compare registers. If the top value is lower than any of the compare registers, a compare match will never occur between
TCNT1 and OCR1x.
As Figure 14-9 shows, the output generated is, in contrast to the phase correct mode, symmetrical in all periods. Since the
OCR1x registers are updated at bottom, the length of the rising and the falling slopes will always be equal. This gives
symmetrical output pulses, and is, therefore, frequency correct.
Using the ICR1 register for defining top works well when using fixed top values. By using ICR1, the OCR1A register is free to
be used for generating a PWM output on OC1A. However, if the base PWM frequency is actively changed by changing the
top value, using the OCR1A as top is clearly a better choice due to its double buffer feature.
In phase and frequency correct PWM mode, the compare units allow generation of PWM waveforms on the OC1x pins.
Setting the COM1x1:0 bits to two will produce a non-inverted PWM, and an inverted PWM output can be generated by
setting the COM1x1:0 to three (see Table 14-4 on page 98). The actual OC1x value will only be visible on the port pin if the
data direction for the port pin is set as output (DDR_OC1x). The PWM waveform is generated by setting (or clearing) the
OC1x register at the compare match between OCR1x and TCNT1 when the counter increments, and clearing (or setting) the
OC1x register at compare match between OCR1x and TCNT1 when the counter decrements. The PWM frequency for the
output when using phase and frequency correct PWM can be calculated by the following equation:
f clk_I/O
f OCnxPFCPWM = ------------------------------2  N  TOP
The variable N represents the prescaler divider (1, 8, 64, 256, or 1024).
The extreme values for the OCR1x register represent special cases when generating a PWM waveform output in the phase
and frequency correct PWM mode. If the OCR1x is set equal to bottom the output will be continuously low, and if set equal to
top, the output will be set to high for non-inverted PWM mode. For inverted PWM the output will have the opposite logic
values.
94
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
14.10 Timer/Counter Timing Diagrams
The Timer/Counter is a synchronous design, and the timer clock (clkT1) is, therefore, shown as a clock enable signal in the
following figures. The figures include information on when interrupt flags are set, and when the OCR1x register is updated
with the OCR1x buffer value (only for modes utilizing double buffering). Figure 14-10 shows a timing diagram for the setting
of OCF1x.
Figure 14-10. Timer/Counter Timing Diagram, Setting of OCF1x, no Prescaling
clkI/O
clkTn
(clkI/O/1)
TCNTn
OCRnx - 1
OCRnx
OCRnx
OCRnx + 1
OCRnx + 2
OCRnx Value
OCFnx
Figure 14-11 shows the same timing data, but with the prescaler enabled.
Figure 14-11. Timer/Counter Timing Diagram, Setting of OCF1x, with Prescaler (fclk_I/O/8)
clkI/O
clkTn
(clkI/O/8)
TCNTn
OCRnx
OCRnx - 1
OCRnx
OCRnx + 1
OCRnx + 2
OCRnx Value
OCFnx
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
95
Figure 14-12 shows the count sequence close to TOP in various modes. When using phase and frequency correct PWM
mode the OCR1x register is updated at BOTTOM. The timing diagrams will be the same, but TOP should be replaced by
BOTTOM, TOP-1 by BOTTOM+1 and so on. The same renaming applies for modes that set the TOV1 flag at BOTTOM.
Figure 14-12. Timer/Counter Timing Diagram, no Prescaling
clkI/O
clkTn
(clkI/O/1)
TCNTn
(CTC and FPWM)
TOP - 1
TOP
BOTTOM
BOTTOM + 1
TCNTn
(PC and PFC PWM)
TOP - 1
TOP
TOP -1
TOP -2
TOVn (FPWM)
and ICFn
(if used as TOP)
OCRnx
(Update at TOP)
Old OCRnx Value
New OCRnx Value
Figure 14-13 shows the same timing data, but with the prescaler enabled.
Figure 14-13. Timer/Counter Timing Diagram, with Prescaler (fclk_I/O/8)
clkI/O
clkTn
(clkI/O/8)
TCNTn
(CTC and FPWM)
TOP - 1
TOP
BOTTOM
BOTTOM + 1
TCNTn
(PC and PFC PWM)
TOP - 1
TOP
TOP - 1
TOP - 2
TOVn (FPWM)
and ICFn
(if used as TOP)
OCRnx
(Update at TOP)
96
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Old OCRnx Value
New OCRnx Value
14.11 Register Description
14.11.1 TCCR1A – Timer/Counter1 Control Register A
Bit
7
0x2F (0x4F)
6
5
4
COM1A1 COM1A0 COM1B1 COM1B0
3
2
1
0
–
–
WGM11
WGM10
Read/Write
R/W
R/W
R/W
R/W
R
R
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TCCR1A
• Bit 7:6 – COM1A1:0: Compare Output Mode for Channel A
• Bit 5:4 – COM1B1:0: Compare Output Mode for Channel B
The COM1A1:0 and COM1B1:0 control the output compare pins' (OC1A and OC1B, respectively) behavior. If one or both of
the COM1A1:0 bits are written to logical one, the OC1A output overrides the normal port functionality of the I/O pin it is
connected to. If one or both of the COM1B1:0 bit are written to logical one, the OC1B output overrides the normal port
functionality of the I/O pin it is connected to. However, note that the data direction register (DDR) bit corresponding to the
OC1A or OC1B pin must be set in order to enable the output driver.
When OC1A or OC1B is connected to the pin, the function of the COM1x1:0 bits is dependent on the WGM13:0 bit settings.
Table 14-2 shows the COM1x1:0 bit functionality when the WGM13:0 bits are set to a normal or CTC mode (non-PWM).
Table 14-2. Compare Output Mode, non-PWM
COM1A1/COM1B1
COM1A0/COM1B0
Description
0
0
Normal port operation, OC1A/OC1B disconnected.
0
1
Toggle OC1A/OC1B on compare match.
1
0
Clear OC1A/OC1B on compare match (Set output to low level).
1
1
Set OC1A/OC1B on compare match (set output to high level).
Table 14-3 shows the COM1x1:0 bit functionality when the WGM13:0 bits are set to the fast PWM mode.
Table 14-3. Compare Output Mode, Fast PWM(1)
COM1A1/COM1B1
COM1A0/COM1B0
0
0
Normal port operation, OC1A/OC1B disconnected.
0
1
WGM13=0: Normal port operation, OC1A/OC1B disconnected.
WGM13=1: Toggle OC1A on compare match, OC1B reserved.
1
0
Clear OC1A/OC1B on compare match, set OC1A/OC1B at
BOTTOM (non-inverting mode)
Set OC1A/OC1B on compare match, clear OC1A/OC1B at
BOTTOM (inverting mode)
A special case occurs when OCR1A/OCR1B equals TOP and COM1A1/COM1B1 is set. In this case the
compare match is ignored, but the set or clear is done at BOTTOM. See Section 14.9.3 “Fast PWM Mode” on
page 90 for more details.
1
Note:
1.
Description
1
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
97
Table 14-4 shows the COM1x1:0 bit functionality when the WGM13:0 bits are set to the phase correct or the phase and
frequency correct, PWM mode.
Table 14-4. Compare Output Mode, Phase Correct and Phase and Frequency Correct PWM(1)
COM1A1/COM1B1
COM1A0/COM1B0
0
0
0
1
1
0
1.
Normal port operation, OC1A/OC1B disconnected.
WGM13=0: Normal port operation, OC1A/OC1B disconnected.
WGM13=1: Toggle OC1A on compare match, OC1B reserved.
Clear OC1A/OC1B on compare match when up-counting. Set
OC1A/OC1B on compare match when down-counting.
Set OC1A/OC1B on compare match when up-counting. Clear
OC1A/OC1B on compare match when down-counting.
A special case occurs when OCR1A/OCR1B equals TOP and COM1A1/COM1B1 is set. See Section 14.9.4
“Phase Correct PWM Mode” on page 92 for more details.
1
Note:
Description
1
• Bit 1:0 – WGM11:0: Waveform Generation Mode
Combined with the WGM13:2 bits found in the TCCR1B register, these bits control the counting sequence of the counter, the
source for maximum (TOP) counter value, and what type of waveform generation is to be used, see Table 14-5 on page 98.
Modes of operation supported by the Timer/Counter unit are: Normal mode (counter), clear timer on compare match (CTC)
mode, and three types of pulse width modulation (PWM) modes (see Section 14.9 “Modes of Operation” on page 89).
Table 14-5. Waveform Generation Mode Bit Description(1)
Mode
WGM13
WGM12
(CTC1)
TOP
Update of
OCR1x at
TOV1 Flag
Set on
0
0
0
0
0
1
0
0
0
1
Normal
0xFFFF
Immediate
MAX
PWM, phase correct, 8-bit
0x00FF
TOP
BOTTOM
2
0
0
1
0
PWM, phase correct, 9-bit
0x01FF
TOP
BOTTOM
3
0
0
1
1
PWM, phase correct, 10-bit
0x03FF
TOP
BOTTOM
4
0
5
0
1
0
0
CTC
OCR1A
Immediate
MAX
1
0
1
Fast PWM, 8-bit
0x00FF
BOTTOM
TOP
6
0
1
1
0
Fast PWM, 9-bit
0x01FF
BOTTOM
TOP
7
0
1
1
1
Fast PWM, 10-bit
0x03FF
BOTTOM
TOP
8
1
0
0
0
PWM, phase and frequency
ICR1
correct
BOTTOM
BOTTOM
9
1
0
0
1
PWM, phase and frequency
OCR1A
correct
BOTTOM
BOTTOM
10
1
0
1
0
PWM, phase correct
ICR1
TOP
BOTTOM
11
1
0
1
1
PWM, phase correct
OCR1A
TOP
BOTTOM
12
1
1
0
0
CTC
ICR1
Immediate
MAX
13
1
1
0
1
(Reserved)
–
–
–
14
1
1
1
0
Fast PWM
ICR1
BOTTOM
TOP
15
Note:
98
WGM11
WGM10 Timer/Counter Mode of
(PWM11) (PWM10) Operation
1
1
1
1
Fast PWM
OCR1A
BOTTOM
TOP
1. The CTC1 and PWM11:0 bit definition names are obsolete. Use the WGM12:0 definitions. However, the
functionality and location of these bits are compatible with previous versions of the timer.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
14.11.2 TCCR1B – Timer/Counter1 Control Register B
Bit
7
6
5
4
3
2
1
0
0x2E (0x4E)
ICNC1
ICES1
–
WGM13
WGM12
CS12
CS11
CS10
Read/Write
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TCCR1B
• Bit 7 – ICNC1: Input Capture Noise Canceller
Setting this bit (to one) activates the input capture noise canceller. When the noise canceller is activated, the input from the
input capture pin (ICP1) is filtered. The filter function requires four successive equal valued samples of the ICP1 pin for
changing its output. The input capture is, therefore, delayed by four oscillator cycles when the noise canceller is enabled.
• Bit 6 – ICES1: Input Capture Edge Select
This bit selects which edge on the input capture pin (ICP1) that is used to trigger a capture event. When the ICES1 bit is
written to logical zero, a falling (negative) edge is used as trigger, and when the ICES1 bit is written to logical one, a rising
(positive) edge will trigger the capture.
When a capture is triggered according to the ICES1 setting, the counter value is copied into the input capture register
(ICR1). The event will also set the input capture flag (ICF1), and this can be used to cause an input capture interrupt, if this
interrupt is enabled.
When the ICR1 is used as top value (see description of the WGM13:0 bits located in the TCCR1A and the TCCR1B
registers), the ICP1 is disconnected, and, consequently, the input capture function is disabled.
• Bit 5 – Reserved Bit
This bit is reserved for future use. For ensuring compatibility with future devices, this bit must be written to logical zero when
TCCR1B is written.
• Bit 4:3 – WGM13:2: Waveform Generation Mode
See TCCR1A register description.
• Bit 2:0 – CS12:0: Clock Select
The three clock select bits select the clock source to be used by the Timer/Counter (see Figure 14-10 on page 95 and
Figure 14-11 on page 95.
Table 14-6. Clock Select Bit Description
CS12
CS11
CS10
Description
0
0
0
No clock source (Timer/Counter stopped).
0
0
1
clkI/O/1 (no prescaling)
0
1
0
clkI/O/8 (from prescaler)
0
1
1
clkI/O/64 (from prescaler)
1
0
0
clkI/O/256 (from prescaler)
1
0
1
clkI/O/1024 (from prescaler)
1
1
0
External clock source on T1 pin. Clock on falling edge.
1
1
1
External clock source on T1 pin. Clock on rising edge.
If external pin modes are used for the Timer/Counter1, transitions on the T1 pin will clock the counter even if the pin is
configured as an output. This feature allows software control of the counting.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
99
14.11.3 TCCR1C – Timer/Counter1 Control Register C
Bit
7
6
5
4
3
2
1
0
0x22 (0x42)
FOC1A
FOC1B
–
–
–
–
–
–
Read/Write
W
W
R
R
R
R
R
R
Initial Value
0
0
0
0
0
0
0
0
TCCR1C
• Bit 7 – FOC1A: Force Output Compare for Channel A
• Bit 6 – FOC1B: Force Output Compare for Channel B
The FOC1A/FOC1B bits are only active when the WGM13:0 bits specify a non-PWM mode. However, for ensuring
compatibility with future devices, these bits must be set to zero when TCCR1A is written while operating in a PWM mode.
When writing a logical one to the FOC1A/FOC1B bit, an immediate compare match is forced on the waveform generation
unit. The OC1A/OC1B output is changed according to its COM1x1:0 bit settings. Note that the FOC1A/FOC1B bits are
implemented as strobes. Therefore, it is the value present in the COM1x1:0 bits that determine the effect of the forced
compare.
A FOC1A/FOC1B strobe will not generate any interrupt, nor will it clear the timer in clear timer on compare match (CTC)
mode using OCR1A as top. The FOC1A/FOC1B bits are always read as zero.
• Bit 5..0 – Reserved Bit
This bit is reserved for future use. For ensuring compatibility with future devices, this bit must be written to logical zero when
the register is written.
14.11.4 TCNT1H and TCNT1L – Timer/Counter1
Bit
7
6
5
4
3
0x2D (0x4D)
TCNT1[15:8]
0x2C (0x4C)
TCNT1[7:0]
2
1
0
TCNT1H
TCNT1L
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
The two Timer/Counter I/O locations (TCNT1H and TCNT1L, combined TCNT1) give direct access for both read and for
write operations to the Timer/Counter unit's 16-bit counter. To ensure that both the high and low bytes are read and written
simultaneously when the CPU accesses these registers, the access is performed using an 8-bit temporary high byte register
(TEMP). This temporary register is shared by all the other 16-bit registers. See Section 14.3 “Accessing 16-bit Registers” on
page 80.
Modifying the counter (TCNT1) while the counter is running introduces a risk of missing a compare match between TCNT1
and one of the OCR1x registers.
Writing to the TCNT1 register blocks (removes) the compare match on the following timer clock for all compare units.
14.11.5 OCR1AH and OCR1AL – Output Compare Register 1 A
Bit
7
6
5
0x2B (0x4B)
0x2A (0x4A)
100
4
3
2
1
0
OCR1A[15:8]
OCR1AH
OCR1A[7:0]
OCR1AL
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
14.11.6 OCR1BH and OCR1BL – Output Compare Register 1 B
Bit
7
6
5
4
3
0x29 (0x49)
OCR1B[15:8]
0x28 (0x48)
OCR1B[7:0]
2
1
0
OCR1BH
OCR1BL
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
The output compare registers contain a 16-bit value that is continuously compared with the counter value (TCNT1). A match
can be used to generate an output compare interrupt, or to generate a waveform output on the OC1x pin.
The output compare registers are 16 bits in size. To ensure that both the high and low bytes are written simultaneously when
the CPU writes to these registers, the access is performed using an 8-bit temporary high byte register (TEMP). This
temporary register is shared by all the other 16-bit registers. See Section 14.3 “Accessing 16-bit Registers” on page 80.
14.11.7 ICR1H and ICR1L – Input Capture Register 1
Bit
7
6
5
4
3
2
1
0
0x25 (0x45)
ICR1[15:8]
ICR1H
0x24 (0x44)
ICR1[7:0]
ICR1L
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
The input capture is updated with the counter (TCNT1) value each time an event occurs on the ICP1 pin (or optionally on the
analog comparator output for Timer/Counter1). The input capture can be used for defining the counter TOP value.
The input capture register is 16 bits in size. To ensure that both the high and low bytes are read simultaneously when the
CPU accesses these registers, the access is performed using an 8-bit temporary high byte register (TEMP). This temporary
register is shared by all the other 16-bit registers. Section 14.3 “Accessing 16-bit Registers” on page 80.
14.11.8 TIMSK1 – Timer/Counter Interrupt Mask Register 1
Bit
7
6
5
4
3
2
1
0
0x0C (0x2C)
–
–
ICIE1
–
–
OCIE1B
OCIE1A
TOIE1
Read/Write
R
R
R/W
R
R
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TIMSK1
• Bit 7,6,4,3 – Reserved Bit
This bit is reserved for future use. For ensuring compatibility with future devices, this bit must be written to logical zero when
the register is written.
• Bit 5 – ICIE1: Timer/Counter1, Input Capture Interrupt Enable
When this bit is written to logical one and the I-flag in the status register is set (interrupts globally enabled), the
Timer/Counter 1 input capture interrupt is enabled. The corresponding interrupt vector (see Section 10. “Interrupts” on page
44) is executed when the ICF1 flag, located in TIFR1, is set.
• Bit 2– OCIE1B: Timer/Counter1, Output Compare B Match Interrupt Enable
When this bit is written to logical one and the I-flag in the status register is set (interrupts globally enabled), the
Timer/Counter 1 output compare B match interrupt is enabled. The corresponding interrupt vector (see Section 10.
“Interrupts” on page 44) is executed when the OCF1B flag, located in TIFR1, is set.
• Bit 1– OCIE1A: Timer/Counter1, Output Compare A Match Interrupt Enable
When this bit is written to logical one and the I-flag in the status register is set (interrupts globally enabled), the
Timer/Counter 1 output compare A match interrupt is enabled. The corresponding interrupt vector (see Section 10.
“Interrupts” on page 44) is executed when the OCF1A flag, located in TIFR1, is set.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
101
• Bit 0 – TOIE1: Timer/Counter1, Overflow Interrupt Enable
When this bit is written to logical one and the I-flag in the status register is set (interrupts globally enabled), the
Timer/Counter 1 overflow interrupt is enabled. The corresponding interrupt vector (see Section 10. “Interrupts” on page 44) is
executed when the TOV1 flag, located in TIFR1, is set.
14.11.9 TIFR1 – Timer/Counter Interrupt Flag Register 1
Bit
7
6
5
4
3
2
1
0
0x0B (0x2B)
–
–
ICIF1
–
–
OCF1B
OCF1A
TOV1
Read/Write
R
R
R/W
R
R
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TIFR1
• Bit 7,6,4,3 – Reserved Bit
This bit is reserved for future use. For ensuring compatibility with future devices, this bit must be written to logical zero when
the register is written.
• Bit 5– ICF1: Timer/Counter1, Input Capture Flag
This flag is set when a capture event occurs on the ICP1 pin. When the input capture register (ICR1) is set by the WGM13:0
to be used as the top value, the ICF1 flag is set when the counter reaches the top value.
ICF1 is automatically cleared when the input capture interrupt vector is executed. Alternatively, ICF1 can be cleared by
writing a logical one to its bit location.
• Bit 2– OCF1B: Timer/Counter1, Output Compare B Match Flag
This flag is set in the timer clock cycle after the counter (TCNT1) value matches the output compare register B (OCR1B).
Note that a forced output compare (1B) strobe will not set the OCF1B flag.
OCF1B is automatically cleared when the output compare match B interrupt vector is executed. Alternatively, OCF1B can be
cleared by writing a logical one to its bit location.
• Bit 1– OCF1A: Timer/Counter1, Output Compare A Match Flag
This flag is set in the timer clock cycle after the counter (TCNT1) value matches the output compare register A (OCR1A).
Note that a forced output compare (1A) strobe will not set the OCF1A flag.
OCF1A is automatically cleared when the output compare match A interrupt vector is executed. Alternatively, OCF1A can be
cleared by writing a logical one to its bit location.
• Bit 0– TOV1: Timer/Counter1, Overflow Flag
The setting of this flag is dependent of the WGM13:0 bit settings. In normal and CTC modes, the TOV1 flag is set when the
timer overflows. See Table 14-5 on page 98 for the TOV1 flag behavior when using another WGM13:0 bit setting.
TOV1 is automatically cleared when the Timer/Counter 1 overflow interrupt vector is executed. Alternatively, TOV1 can be
cleared by writing a logical one to its bit location.
102
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
15.
Timer/Counter Prescaler
Timer/Counter 0, and 1 share the same prescaler module, but the Timer/Counters can have different prescaler settings. The
description below applies to all Timer/Counters. Tn is used as a general name, where n = 0, 1.
The Timer/Counter can be clocked directly by the system clock (by setting the CSn2:0 = 1). This provides the fastest
operation, with a maximum Timer/Counter clock frequency equal to system clock frequency (fCLK_I/O). Alternatively, one of
four taps from the prescaler can be used as a clock source. The prescaled clock has a frequency of either fCLK_I/O/8,
fCLK_I/O/64, fCLK_I/O/256, or fCLK_I/O/1024.
15.1
Prescaler Reset
The prescaler is free running, i.e., it operates independently of the clock select logic of the Timer/Counter, and it is shared by
the Timer/Counter Tn. Because the prescaler is not affected by the Timer/Counter's clock select, the state of the prescaler
will have implications for situations where a prescaled clock is used. One example of prescaling artifacts occurs when the
timer is enabled and clocked by the prescaler (6 > CSn2:0 > 1). The number of system clock cycles from when the timer is
enabled to the first count occurs can be from 1 to N+1 system clock cycles, where N equals the prescaler divisor (8, 64, 256,
or 1024).
It is possible to use the prescaler reset for synchronizing the Timer/Counter to program execution.
15.2
External Clock Source
An external clock source applied to the Tn pin can be used as Timer/Counter clock (clkTn). The Tn pin is sampled once every
system clock cycle by the pin synchronization logic. The synchronized (sampled) signal is then passed through the edge
detector. Figure 15-1 shows a functional equivalent block diagram of the Tn synchronization and edge detector logic. The
registers are clocked at the positive edge of the internal system clock (clkI/O). The latch is transparent in the high period of
the internal system clock.
The edge detector generates one clkT0 pulse for each positive (CSn2:0 = 7) or negative (CSn2:0 = 6) edge it detects.
Figure 15-1. T0 Pin Sampling
Tn
D
Q
D
Q
D
Tn_sync
(to Clock
Select Logic)
Q
LE
clkI/O
Synchronization
Edge Detector
The synchronization and edge detector logic introduces a delay of 2.5 to 3.5 system clock cycles from when an edge has
been applied to the Tn pin to when the counter is updated.
Enabling and disabling of the clock input must be done when Tn has been stable for at least one system clock cycle,
otherwise there is a risk that a false Timer/Counter clock pulse could be generated.
Each half period of the external clock applied must be longer than one system clock cycle to ensure correct sampling. The
external clock must be guaranteed to have less than half the system clock frequency (fExtClk < fclk_I/O/2) given a 50/50 duty
cycle. Because the edge detector uses sampling, the maximum frequency of an external clock it can detect is half the
sampling frequency (Nyquist sampling theorem). However, due to variation of the system clock frequency and duty cycle
caused by oscillator source (crystal, resonator, and capacitor) tolerances, it is recommended that the maximum frequency of
an external clock source is less than fclk_I/O/2.5.
An external clock source can not be prescaled.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
103
Figure 15-2. Prescaler for Timer/Counter0
10-bit T/C Prescaler
CK/64
PSR10
CK/1024
CK/8
Clear
CK/256
clkI/O
Synchronization
T0
0
CS00
CS01
CS02
Timer/Counter 0 Clock Source
clkT0
Note:
15.3
The synchronization logic on the input pins (T0) is shown in Figure 15-1 on page 103.
Register Description
15.3.1 GTCCR – General Timer/Counter Control Register
Bit
7
6
5
4
3
2
1
0
0x23 (0x43)
TSM
–
–
–
–
–
–
PSR10
Read/Write
R/W
R
R
R
R
R
R
R/W
Initial Value
0
0
0
0
0
0
0
0
GTCCR
• Bit 7 – TSM: Timer/Counter Synchronization Mode
Writing the TSM bit to logical one activates the Timer/Counter synchronization mode. In this mode, the value that is written to
the PSR10 bit is kept, hence keeping the prescaler reset signal asserted. This ensures that the Timer/Counter is halted and
can be configured without the risk of advancing during configuration. When the TSM bit is written to logical zero, the PSR10
bit is cleared by hardware, and the Timer/Counter starts counting.
• Bit 0 – PSR10: Prescaler 0 Reset Timer/Counter n
When this bit is set to one, the Timer/Counter n prescaler will be reset. This bit is normally cleared immediately by hardware,
except if the TSM bit is set.
104
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
16.
USI – Universal Serial Interface
16.1
Features
●
●
●
●
●
●
Three-wire synchronous data transfer (master or slave)
Data received interrupt
Wake up from idle mode
In two-wire mode: Wake up from all sleep modes, including power-down mode
Two-wire start condition detector with interrupt capability
Overview
The universal serial interface (USI) provides the basic hardware resources needed for serial communication. Combined with
a minimum of control software, the USI allows significantly higher transfer rates and uses less code space than solutions
based on software only. Interrupts are included to minimize the processor load.
A simplified block diagram of the USI is shown in Figure 16-1. For the actual placement of I/O pins, refer to Section 1-1
“Pinout Atmel ATtiny24/44/84” on page 3. CPU accessible I/O registers, including I/O bits and I/O pins, are shown in bold.
The device-specific I/O register and bit locations are listed in the Section 16.5 “Register Descriptions” on page 111.
Figure 16-1. Universal Serial Interface, Block Diagram
D
DO
Q
(Output only)
LE
3
2
1
0
4-bit Counter
USIDC
USIPF
USIOIF
USIDR
USISIF
(Input/ Open Drain))
Bit0
Bit7
DI/SDA
TIM0 COMP
3
2
0
1
1
0
[1]
USISR
USCK/SCL (Input/ Open Drain))
CLOCK
HOLD
Two-wire Clock
Control Unit
USITC
USICLK
USICS0
USICS1
USIWM0
USIWM1
USIOIE
2
USISIE
16.2
Two-wire synchronous data transfer (master or slave)
USICR
The 8-bit shift register is directly accessible via the data bus and contains the incoming and outgoing data. The register has
no buffering, so the data must be read as quickly as possible to ensure that no data are lost. The most significant bit is
connected to one of two output pins, depending on the wire mode configuration. A transparent latch is inserted between the
serial register output and output pin, which delays the change of data output to the opposite clock edge of the data input
sampling. The serial input is always sampled from the data input (DI) pin independent of the configuration.
The 4-bit counter can be both read and written via the data bus, and can generate an overflow interrupt. Both the serial
register and the counter are clocked simultaneously by the same clock source. This allows the counter to count the number
of bits received or transmitted and generate an interrupt when the transfer is complete. Note that when an external clock
source is selected, the counter counts both clock edges. In this case, the counter counts the number of edges, and not the
number of bits. The clock can be selected from three different sources: the USCK pin, Timer/Counter 0 compare match, or
from software. The two-wire clock control unit can generate an interrupt when a start condition is detected on the two-wire
bus. It can also generate wait states by holding the clock pin low after a start condition is detected, or after the counter
overflows.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
105
16.3
Functional Descriptions
16.3.1 Three-wire Mode
The USI three-wire mode is compliant with the serial peripheral interface (SPI) mode 0 and 1, but does not have the slave
select (SS) pin functionality. However, this feature can be implemented in software if necessary. Pin names used by this
mode are: DI, DO, and USCK.
Figure 16-2. Three-wire Mode Operation, Simplified Diagram
DO
DI
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
USCK
SLAVE
DO
DI
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
USCK
PORTxn
MASTER
Figure 16-2 shows two USI units operating in three-wire mode, one as master and one as slave. The two shift registers are
interconnected in such way that after eight USCK clocks, the data in each register are interchanged. The same clock also
increments the USI's 4-bit counter. The counter overflow (interrupt) flag, or USIOIF, can therefore be used to determine
when a transfer is completed. The clock is generated by the master device software by toggling the USCK pin via the PORT
register, or by writing a logical one to the USITC bit in USICR.
Figure 16-3. Three-wire Mode, Timing Diagram
CYCLE
1
(Reference)
2
3
4
5
6
7
8
USCK
USCK
DO
MSB
DI
MSB
A
B
C
D
6
5
4
3
2
1
LSB
6
5
4
3
2
1
LSB
E
The three-wire mode timing is shown in Figure 16-3. At the top of the figure is a USCK cycle reference. One bit is shifted into
the USI shift register (USIDR) for each of these cycles. The USCK timing is shown for both external clock modes. In external
clock mode 0 (USICS0 = 0), DI is sampled at positive edges, and DO is changed (data register is shifted by one) at negative
edges. External clock mode 1 (USICS0 = 1) uses the opposite edges versus mode 0, i.e., it samples data at negative edges
and changes the output at positive edges. The USI clock modes correspond to the SPI data mode 0 and 1.
106
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Referring to the timing diagram (Figure 16-3 on page 106), a bus transfer involves the following steps:
1. The slave device and master device set up their data output and, depending on the protocol used, enable their
output driver (mark A and B). The output is set up by writing the data to be transmitted to the serial data register.
Enabling of the output is done by setting the corresponding bit in the port data direction register. Note that points A
and B do not have any specific order, but both must be at least one half USCK cycle before point C, where the
data are sampled. This must be done to ensure that the data setup requirement is satisfied. The 4-bit counter is
reset to zero.
2.
The master generates a clock pulse by software toggling the USCK line twice (C and D). The bit value on the
slave and master’s data input (DI) pin is sampled by the USI on the first edge (C), and the data output is changed
on the opposite edge (D). The 4-bit counter will count both edges.
3.
Step 2 is repeated eight times for a complete register (byte) transfer.
4.
After eight clock pulses (i.e., 16 clock edges), the counter will overflow and indicate that the transfer is completed.
The data bytes transferred must now be processed before a new transfer can be initiated. The overflow interrupt
will wake up the processor if it is set to idle mode. Depending on the protocol used, the slave device can now set
its output to high impedance.
16.3.2 SPI Master Operation Example
The following code demonstrates how to use the USI module as a SPI master:
SPITransfer:
out
USIDR,r16
ldi
r16,(1<<USIOIF)
out
USISR,r16
ldi
r16,(1<<USIWM0)|(1<<USICS1)|(1<<USICLK)|(1<<USITC)
SPITransfer_loop:
out
USICR,r16
in
r16, USISR
sbrs
r16, USIOIF
rjmp
SPITransfer_loop
in
r16,USIDR
ret
The code is size optimized using only eight instructions (+ ret). The code example assumes that the DO and USCK pins are
enabled as output in the DDRE register. The value stored in register r16 prior to the function being called is transferred to the
slave device, and when the transfer is completed, the data received from the slave is stored back into the r16 register.
The second and third instructions clear the USI counter overflow flag and the USI counter value. The fourth and fifth
instructions set the three-wire mode, positive edge shift register clock, count at USITC strobe, and toggle USCK. The loop is
repeated 16 times.
The following code demonstrates how to use the USI module as an SPI master with maximum speed (fsck = fck/4):
SPITransfer_Fast:
out
ldi
ldi
USIDR,r16
r16,(1<<USIWM0)|(0<<USICS0)|(1<<USITC)
r17,(1<<USIWM0)|(0<<USICS0)|(1<<USITC)|(1<<USICLK)
out
out
out
out
out
out
out
out
out
out
out
out
out
USICR,r16 ; MSB
USICR,r17
USICR,r16
USICR,r17
USICR,r16
USICR,r17
USICR,r16
USICR,r17
USICR,r16
USICR,r17
USICR,r16
USICR,r17
USICR,r16
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
107
out
out
out
USICR,r17
USICR,r16 ; LSB
USICR,r17
in
r16,USIDR
ret
16.3.3 SPI Slave Operation Example
The following code demonstrates how to use the USI module as a SPI slave:
init:
ldi
r16,(1<<USIWM0)|(1<<USICS1)
out
USICR,r16
...
SlaveSPITransfer:
out
USIDR,r16
ldi
r16,(1<<USIOIF)
out
USISR,r16
SlaveSPITransfer_loop:
in
r16, USISR
sbrs
r16, USIOIF
rjmp
SlaveSPITransfer_loop
in
r16,USIDR
ret
The code is size optimized using only eight instructions (+ ret). The code example assumes that the DO is configured as
output and USCK pin is configured as input in the DDR register. The value stored in register r16 prior to the function being
called is transferred to the master device, and when the transfer is completed, the data received from the master is stored
back into the r16 register.
Note that the first two instructions are for initialization only and need only to be executed once. These instructions set the
three-wire mode and positive edge shift register clock. The loop is repeated until the USI counter overflow flag is set.
108
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
16.3.4 Two-wire Mode
The USI two-wire mode is compliant with the inter-IC (I2C or TWI) bus protocol, but without slew rate limiting on outputs and
input noise filtering. Pin names used by this mode are SCL and SDA.
Figure 16-4. Two-wire Mode Operation, Simplified Diagram
VCC
SDA
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SCL
Two-wire
Clock
Control Unit
HOLD
SCL
SLAVE
SDA
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SCL
PORTxn
MASTER
Figure 16-4 shows two USI units operating in two-wire mode, one as master and one as slave. Only the physical layer is
shown because the system operation is highly dependent of the communication scheme used. The main differences
between the master and slave operation at this level are that the serial clock generation is always done by the master, and
only the slave uses the clock control unit. Clock generation must be implemented in software, but the shift operation is done
automatically by both devices. Note that only clocking on the negative edge to shift data is practical in this mode. The slave
can insert wait states at the start or end of a transfer by forcing the SCL clock low. This means that the master must always
check if the SCL line was actually released after it has generated a positive edge.
Because the clock also increments the counter, a counter overflow can be used to indicate that the transfer has completed.
The master generates clock by the by toggling the USCK pin via the PORT register.
The data direction is not given by the physical layer. A protocol, like the one used by the TWI-bus, must be implemented to
control the data flow.
Figure 16-5. Two-wire Mode, Typical Timing Diagram
SDA
SCL
1 to 7
S
A
ADDRESS
B
C
8
9
1 to 8
9
1 to 8
9
R/W
ACK
DATA
ACK
DATA
ACK
D
E
P
F
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
109
Referring to the timing diagram (Figure 16-5 on page 109), a bus transfer involves the following steps:
1. The start condition is generated by the master by forcing the SDA line low while the SCL line is high (A). SDA can
be forced low either by writing a logical zero to bit 7 of the shift register, or by setting the corresponding bit in the
PORT register to zero. Note that the data direction register bit must be set to one for the output to be enabled. The
slave device's start detector logic (Figure 16-6) detects the start condition and sets the USISIF flag. The flag can
generate an interrupt if necessary.
2.
In addition, the start detector will hold the SCL line low after the master has forced a negative edge on this line (B).
This allows the slave to wake up from sleep or complete its other tasks before setting up the shift register to
receive the address. This is done by clearing the start condition flag and resetting the counter.
3.
The master set the first bit to be transferred and releases the SCL line (C). The Slave samples the data and shift it
into the serial register at the positive edge of the SCL clock.
4.
After eight bits containing the slave address and data direction (read or write) are transferred, the slave counter
overflows and the SCL line is forced low (D). If the slave is not the one the master has addressed, it releases the
SCL line and waits for a new start condition.
5.
If the slave is addressed, it holds the SDA line low during the acknowledgment cycle before holding the SCL line
low again (i.e., the counter register must be set to 14 before releasing SCL at (D)). Depending on the state of the
R/W bit, the master or slave enables its output. If the bit is set, a master read operation is in progress (i.e., the
slave drives the SDA line). The slave can hold the SCL line low after the acknowledgement cycle (E).
6.
Multiple bytes can now be transmitted, all in same direction, until a stop condition is given by the master (F), or a
new start condition is given.
If the slave is not able to receive more data, it does not acknowledge the data byte it has last received. When the master
does a read operation, it must terminate the operation by forcing the acknowledge bit low after the last byte is transmitted.
Figure 16-6. Start Condition Detector, Logic Diagram
USISIF
D
SDA
Q
CLR
D
Q
CLOCK
HOLD
CLR
SCL
Write (USISIF)
16.3.5 Start Condition Detector
The start condition detector is shown in Figure 16-6. The SDA line is delayed (in the range of 50 to 300ns) to ensure valid
sampling of the SCL line. The start condition detector is only enabled in two-wire mode.
The start condition detector is working asynchronously, and can, therefore, wake up the processor from the power-down
sleep mode. However, the protocol used might have restrictions on the SCL hold time. Therefore, when using this feature in
this case, the oscillator start-up time set by the CKSEL fuses (see Section 7.1 “Clock Systems and their Distribution” on page
24) must also be taken into consideration. See the USISIF bit description in Section 16.5.3 “USISR – USI Status Register” on
page 112 for further details.
16.3.6 Clock speed considerations
Maximum frequency for SCL and SCK is fCK /4. This is also the maximum data transmit and receive rate in both two- wire
and three-wire mode. In two-wire slave mode the two-wire clock control unit will hold SCL low until the slave is ready to
receive more data. This may reduce the actual data rate in two-wire mode.
110
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
16.4
Alternative USI Usage
When the USI unit is not used for serial communication, it can be set up to do alternative tasks due to its flexible design.
16.4.1 Half-duplex Asynchronous Data Transfer
By utilizing the shift register in three-wire mode, it is possible to implement a more compact and higher performance UART
than by software only.
16.4.2 4-bit Counter
The 4-bit counter can be used as a stand-alone counter with overflow interrupt. Note that if the counter is clocked externally,
both clock edges will generate an increment.
16.4.3 12-bit Timer/Counter
Combining the USI 4-bit counter and Timer/Counter0 allows them to be used as a 12-bit counter.
16.4.4 Edge-Triggered External Interrupt
By setting the counter to maximum value (F), it can function as an additional external interrupt. The overflow flag and
interrupt enable bit are then used for the external interrupt. This feature is selected by the USICS1 bit.
16.4.5 Software Interrupt
The counter overflow interrupt can be used as a software interrupt triggered by a clock strobe.
16.5
Register Descriptions
16.5.1 USIBR – USI Data Buffer
Bit
7
0x10 (0x30)
MSB
6
5
4
3
2
1
0
Read/Write
R
R
R
R
R
R
R
R
Initial Value
0
0
0
0
0
0
0
0
5
4
3
2
1
LSB
USIBR
16.5.2 USIDR – USI Data Register
Bit
7
0x0F (0x2F)
MSB
6
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
LSB
USIDR
The USI uses no buffering for the serial register, i.e., when accessing the data register (USIDR) the serial register is
accessed directly. If a serial clock occurs during the same cycle the register is written, the register will contain the value
written and no shift is performed. A (left) shift operation is performed depending on the USICS1..0 bit settings. The shift
operation can be controlled by an external clock edge, by a Timer/Counter 0 compare match, or directly by software using
the USICLK strobe bit. Note that even when no wire mode is selected (USIWM1..0 = 0), both the external data input
(DI/SDA) and the external clock input (USCK/SCL) can still be used by the shift register.
The output pin in use - DO or SDA, depending on the wire mode - is connected via the output latch to the most-significant Bit
(bit 7) of the data register. The output latch is open (transparent) during the first half of a serial clock cycle when an external
clock source is selected (USICS1 = 1), and constantly open when an internal clock source is used (USICS1 = 0). The output
will be changed immediately when a new MSB is written as long as the latch is open. The latch ensures that data input is
sampled and data output is changed on opposite clock edges.
Note that the corresponding data direction register to the pin must be set to one for enabling data output from the shift
register.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
111
16.5.3 USISR – USI Status Register
Bit
7
6
5
4
3
0x0E (0x2E)
USISIF
USIOIF
USIPF
USIDC
USICNT3
2
1
0
Read/Write
R/W
R/W
R/W
R
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
USICNT2 USICNT1 USICNT0
USISR
The status register contains interrupt flags, line status flags and the counter value.
• Bit 7 – USISIF: Start Condition Interrupt Flag
When two-wire mode is selected, the USISIF flag is set (one) when a start condition is detected. When output disable mode
or three-wire mode is selected and (USICSx = 0b11 and USICLK = 0) or (USICS = 0b10 and USICLK = 0), any edge on the
SCK pin sets the flag.
An interrupt will be generated when the flag is set while the USISIE bit in USICR and the global interrupt enable flag are set.
The flag will only be cleared by writing a logical one to the USISIF bit. Clearing this bit will release the start detection hold of
USCL in two-wire mode. A start condition interrupt will wake up the processor from all sleep modes.
• Bit 6 – USIOIF: Counter Overflow Interrupt Flag
This flag is set (one) when the 4-bit counter overflows (i.e., at the transition from 15 to 0). An interrupt will be generated when
the flag is set while the USIOIE bit in USICR and the global interrupt enable flag are set. The flag is cleared if a logical one is
written to the USIOIF bit or by reading the USIBR register. Clearing this bit will release the counter overflow hold of SCL in
two-wire mode.
A counter overflow interrupt will wake up the processor from Idle sleep mode.
• Bit 5 – USIPF: Stop Condition Flag
When two-wire mode is selected, the USIPF flag is set (one) when a stop condition is detected. The flag is cleared by writing
a logical one to this bit. Note that this is not an interrupt flag. This signal is useful when implementing two-wire bus master
arbitration.
• Bit 4 – USIDC: Data Output Collision
This bit is logical one when bit 7 in the shift register differs from the physical pin value. The flag is only valid when two-wire
mode is used. This signal is useful when implementing two-wire bus master arbitration.
• Bits 3..0 – USICNT3..0: Counter Value
These bits reflect the current 4-bit counter value. The 4-bit counter value can be read or written directly by the CPU.
The 4-bit counter increments by one for each clock generated either by the external clock edge detector, by a Timer/Counter
0 compare match, or by software using USICLK or USITC strobe bits. The clock source depends on the setting of the
USICS1..0 bits. For external clock operation, a special feature is added that allows the clock to be generated by writing to the
USITC strobe bit. This feature is enabled by writing a logical one to the USICLK bit while setting an external clock source
(USICS1 = 1).
Note that even when no wire mode is selected (USIWM1..0 = 0), the external clock input (USCK/SCL) can still be used by
the counter.
16.5.4 USICR – USI Control Register
Bit
7
6
5
4
3
2
1
0
0x0D (0x2D)
USISIE
USIOIE
USIWM1
USIWM0
USICS1
USICS0
USICLK
USITC
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
W
W
Initial Value
0
0
0
0
0
0
0
0
USICR
The control register includes interrupt enable control, wire mode setting, clock select setting, and clock strobe.
• Bit 7 – USISIE: Start Condition Interrupt Enable
Setting this bit to one enables the start condition detector interrupt. If there is a pending interrupt when the USISIE and the
global interrupt enable flag are set to one, this will immediately be executed. See the USISIF bit description in Section 16.5.3
“USISR – USI Status Register” on page 112 for further details.
112
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
• Bit 6 – USIOIE: Counter Overflow Interrupt Enable
Setting this bit to one enables the counter overflow interrupt. If there is a pending interrupt when the USIOIE and the global
interrupt enable flag are set to one, this will immediately be executed. See the USIOIF bit description in Section 16.5.3
“USISR – USI Status Register” on page 112 for further details.
• Bit 5..4 – USIWM1..0: Wire Mode
These bits set the type of wire mode to be used. Basically, only the function of the outputs are affected by these bits. Data
and clock inputs are not affected by the mode selected, and will always have the same function. The counter and shift
register can, therefore, be clocked externally, and data input sampled, even when outputs are disabled. The relation
between USIWM1..0 and USI operation is summarized in Table 16-1.
Table 16-1. Relations between USIWM1..0 and the USI Operation
USIWM1
USIWM0
0
0
Description
Outputs, clock hold, and start detector disabled. Port pins operate as normal.
Three-wire mode. Uses DO, DI, and USCK pins.
0
1
The data output (DO) pin overrides the corresponding bit in the PORT register in this mode.
However, the corresponding DDR bit still controls the data direction. When the port pin is set
as input the pins pull-up is controlled by the PORT bit.
The data input (DI) and serial clock (USCK) pins do not affect the normal port operation.
When operating as master, clock pulses are software generated by toggling the PORT
register, while the data direction is set to output. The USITC bit in the USICR register can be
used for this purpose.
Two-wire mode. Uses SDA (DI) and SCL (USCK) pins(1).
The serial data (SDA) and the serial clock (SCL) pins are bi-directional and use
open-collector output drivers. The output drivers are enabled by setting the corresponding bit
for SDA and SCL in the DDR register.
1
0
When the output driver is enabled for the SDA pin, the output driver will force the SDA line
low if the output of the shift register or the corresponding bit in the PORT register is zero.
Otherwise, the SDA line will not be driven (i.e., it is released). When the SCL pin output
driver is enabled, the SCL line will be forced low if the corresponding bit in the PORT register
is zero, or by the start detector. Otherwise the SCL line will not be driven.
The SCL line is held low when a start detector detects a start condition and the output is
enabled. Clearing the start condition flag (USISIF) releases the line. The SDA and SCL pin
inputs are not affected by enabling this mode.
Pull-ups on the SDA and SCL port pins are disabled in two-wire mode.
Two-wire mode. Uses SDA and SCL pins.
1
Note:
Same operation as for the Two-wire mode described above, except that the SCL line is also
held low when a counter overflow occurs, and is held low until the counter overflow flag
(USIOIF) is cleared.
The DI and USCK pins are renamed to serial data (SDA) and serial clock (SCL), respectively, to avoid
confusion between the modes of operation.
1
1.
• Bit 3..2 – USICS1..0: Clock Source Select
These bits set the clock source for the shift register and counter. The data output latch ensures that the output is changed at
the opposite edge of the sampling of the data input (DI/SDA) when using the external clock source (USCK/SCL). When the
software strobe or Timer/Counter 0 compare match clock option is selected, the output latch is transparent and, therefore,
the output is changed immediately. Clearing the USICS1..0 bits enables the software strobe option. When using this option,
writing a logical one to the USICLK bit clocks both the shift register and the counter. For the external clock source
(USICS1 = 1), the USICLK bit is no longer used as a strobe, but selects between external clocking and software clocking by
the USITC strobe bit.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
113
Table 16-2 shows the relationship between the USICS1..0 and USICLK settings and the clock source used for the shift
register and the 4-bit counter.
Table 16-2. Relations between the USICS1..0 and USICLK Setting
USICS1
USICS0
USICLK
Shift Register Clock Source
4-bit Counter Clock Source
0
0
0
No clock
No Clock
0
0
1
Software clock strobe (USICLK)
Software clock strobe (USICLK)
0
1
X
Timer/Counter0 compare match
Timer/Counter0 compare match
1
0
0
External, positive edge
External, both edges
1
1
0
External, negative edge
External, both edges
1
0
1
External, positive edge
Software clock strobe (USITC)
1
1
1
External, negative edge
Software clock strobe (USITC)
• Bit 1 – USICLK: Clock Strobe
Writing a logical one to this bit location strobes the shift register to shift one step, and the counter to increment by one,
provided that the USICS1..0 bits are set to zero, and by doing so, the software clock strobe option is selected. The output will
change immediately when the clock strobe is executed, i.e., in the same instruction cycle. The value shifted into the shift
register is sampled during the previous instruction cycle. The bit will be read as zero.
When an external clock source is selected (USICS1 = 1), the USICLK function is changed from a clock strobe to a clock
select register. Setting the USICLK bit in this case will select the USITC strobe bit as the clock source for the 4-bit counter
(see Table 16-2).
• Bit 0 – USITC: Toggle Clock Port Pin
Writing a logical one to this bit location toggles the USCK/SCL value either from 0 to 1, or from 1 to 0. The toggling is
independent of the setting in the data direction register, but if the PORT value is to be shown on the pin, DDRE4 must be set
as output (to one). This feature allows easy clock generation when implementing master devices. The bit will be read as
zero.
When an external clock source is selected (USICS1 = 1) and the USICLK bit is set to one, writing to the USITC strobe bit will
directly clock the 4-bit counter. This allows an early detection of when the transfer is done when operating as a master
device.
114
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
17.
Analog Comparator
The analog comparator compares the input values on the positive pin (AIN0) and negative pin (AIN1). When the voltage on
the positive pin (AIN0) is higher than the voltage on the negative pin (AIN1), the analog comparator output (ACO) is set. The
comparator can trigger a separate interrupt, exclusive to the analog comparator. The user can select Interrupt triggering on
comparator output rise, fall or toggle. A block diagram of the comparator and its surrounding logic is shown in Figure 17-1 on
page 115.
Figure 17-1. Analog Comparator Block Diagram(1)
VCC
Bandgap
Reference
ACBG
ACD
ACIE
AIN0
+
-
Analog
Comparator
IRQ
Interrupt
Select
ACI
AIN1
ACIS1
ACIS0
ACIC
ACME
ADEN
To T/C1 Capture
Trigger MUX
ACO
ADC Multiplexer
Output(1)
Notes:
17.1
1.
See Table 17-1.
2.
See Figure 1-1 on page 3 and Table 12-9 on page 61 for analog comparator pin placement.
Analog Comparator Multiplexed Input
When the analog-to-digital converter (ADC) is configured as a single-ended input channel, it is possible to select any of the
ADC7..0 pins to replace the negative input to the analog comparator. The ADC multiplexer is used to select this input, and,
consequently, the ADC must be switched off to utilize this feature. If the analog comparator multiplexer enable bit (ACME in
ADCSRB) is set and the ADC is switched off (ADEN in ADCSRA is zero), MUX1..0 in ADMUX select the input pin to replace
the negative input to the analog comparator, as shown in Table 17-1. If ACME is cleared or ADEN is set, AIN1 is applied to
the negative input of the analog comparator.
Table 17-1. Analog Comparator Multiplexed Input
ACME
ADEN
MUX4..0
Analog Comparator Negative Input
0
x
xx
AIN1
1
1
xx
AIN1
1
0
00000
ADC0
1
0
00001
ADC1
1
0
00010
ADC2
1
0
00011
ADC3
1
0
00100
ADC4
1
0
00101
ADC5
1
0
00110
ADC6
1
0
00111
ADC7
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
115
17.2
Register Description
17.2.1 ADCSRB – ADC Control and Status Register B
Bit
7
6
5
4
3
2
1
0
0x03 (0x23)
BIN
ACME
–
ADLAR
–
ADTS2
ADTS1
ADTS0
Read/Write
R/W
R/W
R
R/w
R
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
ADCSRB
• Bit 6 – ACME: Analog Comparator Multiplexer Enable
When this bit is written logical one and the ADC is switched off (ADEN in ADCSRA is zero), the ADC multiplexer selects the
negative input to the analog comparator. When this bit is written logical zero, AIN1 is applied to the negative input of the
analog comparator. For a detailed description of this bit, see Section 17.1 “Analog Comparator Multiplexed Input” on page
115.
17.2.2 ACSR – Analog Comparator Control and Status Register
Bit
7
6
5
4
3
2
1
0
0x08 (0x28)
ACD
ACBG
Read/Write
R/W
R/W
ACO
ACI
ACIE
ACIC
ACIS1
ACIS0
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
N/A
0
0
0
0
0
ACSR
• Bit 7 – ACD: Analog Comparator Disable
When this bit is written logical one, the power to the analog comparator is switched off. This bit can be set at any time to turn
off the analog comparator. This will reduce power consumption in active and idle mode. When changing the ACD bit, the
analog comparator interrupt must be disabled by clearing the ACIE bit in ACSR. Otherwise an interrupt can occur when the
bit is changed.
• Bit 6 – ACBG: Analog Comparator Bandgap Select
When this bit is set, a fixed bandgap reference voltage replaces the positive input to the ana- log comparator. When this bit
is cleared, AIN0 is applied to the positive input of the analog comparator.
• Bit 5 – ACO: Analog Comparator Output
The output of the analog comparator is synchronized and then directly connected to ACO. The synchronization introduces a
delay of one to two clock cycles.
• Bit 4 – ACI: Analog Comparator Interrupt Flag
This bit is set by hardware when a comparator output event triggers the interrupt mode defined by ACIS1 and ACIS0. The
analog comparator interrupt routine is executed if the ACIE bit is set and the I-bit in SREG is set. ACI is cleared by hardware
when executing the corresponding interrupt handling vector. Alternatively, ACI is cleared by writing a logical one to the flag.
• Bit 3 – ACIE: Analog Comparator Interrupt Enable
When the ACIE bit is written logical one and the I-bit in the status register is set, the analog comparator interrupt is activated.
When written logical zero, the interrupt is disabled.
• Bit 2 – ACIC: Analog Comparator Input Capture Enable
When written logical one, this bit enables the input capture function in Timer/Counter 1 to be triggered by the analog
comparator. The comparator output is in this case directly connected to the input capture front-end logic, making the
comparator utilize the noise canceller and edge select features of the Timer/Counter 1 input capture interrupt. When written
logical zero, no connection between the analog comparator and the input capture function exists. To make the comparator
trigger the Timer/Counter 1 input capture interrupt, the ICIE1 bit in the timer interrupt mask register (TIMSK1) must be set.
116
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
• Bits 1, 0 – ACIS1, ACIS0: Analog Comparator Interrupt Mode Select
These bits determine which comparator events trigger the analog comparator interrupt. The different settings are shown in
Table 17-2.
Table 17-2. ACIS1/ACIS0 Settings
ACIS1
ACIS0
Interrupt Mode
0
0
Comparator interrupt on output toggle.
0
1
Reserved
1
0
Comparator interrupt on falling output edge.
1
1
Comparator interrupt on rising output edge.
When changing the ACIS1/ACIS0 bits, the analog comparator interrupt must be disabled by clearing its interrupt enable bit in
the ACSR. Otherwise, an interrupt can occur when the bits are changed.
17.2.3 DIDR0 – Digital Input Disable Register 0
Bit
7
6
5
4
3
2
1
0
0x01 (0x21)
ADC7D
ADC6D
ADC5D
ADC4D
ADC3D
ADC2D
ADC1D
ADC0D
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
DIDR0
• Bits 1, 0 – ADC0D,ADC1D: ADC 1/0 Digital input buffer disable
When this bit is written logical one, the digital input buffer on the AIN1/0 pin is disabled. The corresponding PIN register bit
will always read as zero when this bit is set. When an analog signal is applied to the AIN1/0 pin and the digital input from this
pin is not needed, this bit should be written logical one to reduce power consumption in the digital input buffer.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
117
18.
Analog-to-Digital Converter
18.1
Features
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
18.2
10-bit resolution
1.0 LSB integral non-linearity
±2 LSB absolute accuracy
65 - 260µs conversion time
Up to 76kSPS at maximum resolution
Eight multiplexed single-ended input channels
Twelve differential input channels with selectable gain (1x, 20x)
Temperature sensor input channel
Optional left adjustment for ADC result readout
0 to VCC ADC input voltage range
1.1V ADC reference voltage
Free-running or single-conversion mode
ADC start conversion by auto triggering on interrupt sources
Interrupt on ADC conversion complete
Sleep mode noise canceller
Unipolar / bipolar input mode
Input polarity reversal channels
Overview
The Atmel® ATtiny24/44/84 features a 10-bit successive approximation analog-to-digital converter (ADC). The ADC is
connected to 8-pin port A for external sources. In addition to external sources, the internal temperature sensor can be
measured by the ADC. The analog multiplexer allows 8 single-ended channels or 12 differential channels from port A. The
programmable gain stage provides amplification steps 0dB (1x) and 26dB (20x) for 12 differential ADC channels.
The ADC contains a sample-and-hold circuit which ensures that the input voltage to the ADC is held at a constant level
during conversion. A block diagram of the ADC is shown in Figure 18-1 on page 119.
And internal reference voltage of nominally 1.1V is provided on chip. Alternatively, VCC can be used as reference voltage for
single-ended channels. There is also an option to use an external voltage reference and turn off the internal voltage
reference.
118
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Figure 18-1. Analog-to-Digital Converter Block Schematic
ADC Conversion
Complete IRQ
Interrupt
Flags
ADTS2 to ADTS0
Internal
Reference
1.1V
ADPS0
ADPS1
ADPS2
ADIF
ADSC
ADATE
Gain Selection
VCC
Prescaler
MUX Decoder
0
ADC Data Register
(ADCH/ADCL)
Trigger
Select
Channel Selection
REFS1...REFS0
AREF
ADLAR
BIN
IPR
15
ADC CTRL and Status A
Register (ADCSRA)
ADEN
ADC Multiplexer
Select (ADMUX)
MUX4...MUX0
ADC CTRL & Status B
Register (ADCSRB)
ADC[9:0]
ADIF
ADIE
8-bit Data Bus
START
Conversion Logic
Temperature
Sensor
Sample and Hold
Comparator
10-bit DAC
-
ADC8
+
AGND
Single Ended/ Differential Selection
ADC7
ADC
MULTIPLEXER
OUTPUT
ADC6
ADC5
ADC4
POS.
Input
MUX
+
-
ADC3
Gain
Amplifier
ADC2
ADC1
ADC0
NEG.
Input
MUX
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
119
18.3
ADC Operation
The ADC converts an analog input voltage to a 10-bit digital value through successive approximation. The minimum value
represents GND, and the maximum value represents the reference voltage. The voltage reference for the ADC may be
selected by writing to the REFS1..0 bits in the ADMUX register. The VCC supply, the AREF pin or an internal 1.1V voltage
reference may be selected as the ADC voltage reference.
The analog input channel and differential gain are selected by writing to the MUX5..0 bits in the ADMUX register. Any of the
eight ADC input pins ADC7..0 can be selected as single-ended inputs to the ADC. For differential measurements, all
adjacent analog inputs can be selected as an input pair. Every input can also be measured with ADC3. These pairs of
differential inputs are measured by the ADC through the differential gain amplifier.
If differential channels are selected, the differential gain stage amplifies the voltage difference between the selected input
pair by the selected gain factor, 1x or 20x, according to the setting of the MUX0 bit in the ADMUX register. This amplified
value then becomes the analog input to the ADC. If single-ended channels are used, the gain amplifier is bypassed
altogether.
The offset of the differential channels can be measure by selecting the same input for both negative and positive input.
Offset calibration can be done for ADC0, ADC3 and ADC7. When ADC0, ADC3, or ADC7 is selected as both the positive
and negative input to the differential gain amplifier, the remaining offset in the gain stage and conversion circuitry can be
measured directly as the result of the conversion. This figure can be subtracted from subsequent conversions with the same
gain setting to reduce offset error to below 1 LSB.
The on-chip temperature sensor is selected by writing “100010” to the MUX5..0 bits in the ADMUX register.
The ADC is enabled by setting the ADC enable bit (ADEN) in ADCSRA. Voltage reference and input channel selections will
not go into effect until ADEN is set. The ADC does not consume power when ADEN is cleared, so it is recommended to
switch off the ADC before entering power saving sleep modes.
The ADC generates a 10-bit result which is presented in the ADC data registers, ADCH and ADCL. By default, the result is
presented right adjusted, but can optionally be presented left adjusted by setting the ADLAR bit in ADCSRB.
If the result is left adjusted and no more than 8-bit precision is required, it is sufficient to read ADCH. Otherwise, ADCL must
be read first, then ADCH, to ensure that the content of the data registers belongs to the same conversion. Once ADCL is
read, ADC access to data registers is blocked. This means that if ADCL has been read, and a conversion completes before
ADCH is read, neither register is updated, and the result from the conversion is lost. When ADCH is read, ADC access to the
ADCH and ADCL registers is re-enabled.
The ADC has its own interrupt which can be triggered when a conversion completes. When ADC access to the data registers
is prohibited between reading of ADCH and ADCL, the interrupt will trigger even if the result is lost.
18.4
Starting a Conversion
A single conversion is started by writing a logical one to the ADC start conversion bit, ADSC. This bit stays high as long as
the conversion is in progress, and will be cleared by hardware when the conversion is completed. If a different data channel
is selected while a conversion is in progress, the ADC will finish the current conversion before performing the channel
change.
Alternatively, a conversion can be triggered automatically by various sources. Auto triggering is enabled by setting the ADC
auto trigger enable bit (ADATE) in ADCSRA. The trigger source is selected by setting the ADC trigger select bits (ADTS) in
ADCSRB (see the description of the ADTS bits for a list of the trigger sources). When a positive edge occurs on the selected
trigger signal, the ADC prescaler is reset and a conversion is started. This provides a method of starting conversions at fixed
intervals. If the trigger signal still is set when the conversion completes, a new conversion will not be started. If another
positive edge occurs on the trigger signal during conversion, the edge will be ignored. Note that an interrupt flag will be set
even if the specific interrupt is disabled or the global interrupt enable bit in SREG is cleared. A conversion can thus be
triggered without causing an interrupt. However, the interrupt flag must be cleared in order to trigger a new conversion at the
next interrupt event
120
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Figure 18-2. ADC Auto Trigger Logic
ADTS[2:0]
Prescaler
ADIF
START
ADATE
CLKADC
SOURCE 1
.
.
.
.
Conversion
Logic
Edge
Detector
SOURCE n
ADSC
Using the ADC interrupt flag as a trigger source makes the ADC start a new conversion as soon as the ongoing conversion
has finished. The ADC then operates in free running mode, constantly sampling and updating the ADC data register. The
first conversion must be started by writing a logical one to the ADSC bit in ADCSRA. In this mode, the ADC will perform
successive conversions independently of whether the ADC interrupt flag (ADIF) is cleared or not.
If auto triggering is enabled, single conversions can be started by writing ADSC in ADCSRA to logical one. ADSC can also
be used to determine if a conversion is in progress. The ADSC bit will be read as logical one during a conversion
independently of how the conversion was started.
Prescaling and Conversion Timing
Figure 18-3. ADC Prescaler
ADEN
START
Reset
7-bit ADC Prescaler
CK/64
CK/128
CK/32
CK/16
CK/8
CK/4
CK
CK/2
18.5
ADPS0
ADPS1
ADPS2
ADC Clock Source
By default, the successive approximation circuitry requires an input clock frequency between 50kHz and 200kHz to get
maximum resolution. If a lower resolution than 10 bits is needed, the input clock frequency to the ADC can be higher than
200kHz to get a higher sample rate.The ADC module contains a prescaler, which generates an acceptable ADC clock
frequency from any CPU frequency above 100kHz.
The prescaling is set by the ADPS bits in ADCSRA. The prescaler starts counting from the moment the ADC is switched on
by setting the ADEN bit in ADCSRA. The prescaler keeps running for as long as the ADEN bit is set, and is continuously
reset when ADEN is low.
When initiating a single-ended conversion by setting the ADSC bit in ADCSRA, the conversion starts at the following rising
edge of the ADC clock cycle.
A normal conversion takes 13 ADC clock cycles. The first conversion after the ADC is switched on (ADEN in ADCSRA is set)
takes 25 ADC clock cycles in order to initialize the analog circuitry.
The actual sample-and-hold takes place 1.5 ADC clock cycles after the start of a normal conversion and 14.5 ADC clock
cycles after the start of a first conversion. When a conversion is complete, the result is written to the ADC data registers, and
ADIF is set. In single-conversion mode, ADSC is cleared simultaneously. The software may then set ADSC again, and a
new conversion will be initiated on the first rising ADC clock edge.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
121
When auto triggering is used, the prescaler is reset when the trigger event occurs. This assures a fixed delay from the trigger
event to the start of conversion. In this mode, the sample-and-hold takes place two ADC clock cycles after the rising edge on
the trigger source signal. Three additional CPU clock cycles are used for synchronization logic.
In free running mode, a new conversion will be started immediately after the conversion completes, while ADSC remains
high. For a summary of conversion times, see Table 18-1 on page 123.
Figure 18-4. ADC Timing Diagram, First Conversion (Single Conversion Mode)
Next
Conversion
First Conversion
Cycle Number
1
2
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
2
3
ADC Clock
ADEN
ADSC
ADIF
ADCH
Sign and MSB of Result
ADCL
LSB of Result
MUX and REFS
Update
Conversion
Complete
Sample and Hold
MUX and REFS
Update
Figure 18-5. ADC Timing Diagram, Single Conversion
Next Conversion
One Conversion
Cycle Number
1
2
3
4
5
6
7
8
9
10
11
12
13
1
2
3
ADC Clock
ADSC
ADIF
ADCH
Sign and MSB of Result
ADCL
LSB of Result
Sample and Hold
MUX and REFS
Update
122
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Conversion
Complete
MUX and REFS
Update
Figure 18-6. ADC Timing Diagram, Auto Triggered Conversion
Next Conversion
One Conversion
Cycle Number
1
2
3
4
5
6
7
8
9
10
11
12
13
1
2
ADC Clock
Trigger
Source
ADATE
ADIF
ADCH
Sign and MSB of Result
ADCL
LSB of Result
Sample and Hold
Prescaler
Reset
Prescaler
Reset
Conversion
Complete
MUX and REFS
Update
Figure 18-7. ADC Timing Diagram, Free Running Conversion
One Conversion
Cycle Number
11
12
Next Conversion
13
1
2
3
4
ADC Clock
ADSC
ADIF
ADCH
Sign and MSB of Result
ADCL
LSB of Result
Sample and Hold
Conversion
Complete
MUX and REFS
Update
Table 18-1. ADC Conversion Time
Sample-and-Hold (Cycles from Start
of Conversion)
Conversion Time (Cycles)
First conversion
14.5
25
Normal conversions
1.5
13
2
13.5
Condition
Auto triggered conversions
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
123
18.6
Changing Channel or Reference Selection
The MUX5:0 and REFS1:0 bits in the ADMUX register are single-buffered through a temporary register to which the CPU
has random access. This ensures that the channel and reference selection only takes place at a safe point during the
conversion. The channel and reference selection is continuously updated until a conversion is started. Once the conversion
starts, the channel and reference selection is locked to ensure a sufficient sampling time for the ADC. Continuous updating
resumes in the last ADC clock cycle before the conversion completes (ADIF in ADCSRA is set). Note that the conversion
starts on the following rising ADC clock edge after ADSC is written. The user is thus advised not to write new channel or
reference selection values to ADMUX until one ADC clock cycle after ADSC is written.
If auto triggering is used, the exact time of the triggering event can be indeterministic. Special care must be taken when
updating the ADMUX register in order to control which conversion will be affected by the new setting.
If both ADATE and ADEN are written to logical one, an interrupt event can occur at any time. If the ADMUX register is
changed in this period, the user cannot tell if the next conversion is based on the old or the new setting. The ADMUX register
can be safely updated in the following ways:
a. When ADATE or ADEN is cleared.
b.
During conversion, minimum one ADC clock cycle after the trigger event.
c.
After a conversion, before the interrupt flag used as the trigger source is cleared.
When updating the ADMUX register in one of these conditions, the new setting will affect the next ADC conversion.
18.6.1 ADC Input Channels
When changing channel selections, the user should observe the following guidelines to ensure that the correct channel is
selected:
In single-conversion mode, always select the channel before starting the conversion. The channel selection may be changed
one ADC clock cycle after writing logical one to ADSC. However, the simplest method is to wait for the conversion to
complete before changing the channel selection.
In free running mode, always select the channel before starting the first conversion. The channel selection may be changed
one ADC clock cycle after writing logical one to ADSC. However, the simplest method is to wait for the first conversion to
complete, and then change the channel selection. Because the next conversion has already started automatically, the next
result will reflect the previous channel selection. Subsequent conversions will reflect the new channel selection.
18.6.2 ADC Voltage Reference
The reference voltage for the ADC (VREF) indicates the conversion range for the ADC. Single-ended channels that exceed
VREF will result in codes close to 0x3FF. VREF can be selected as either VCC, internal 1.1V reference, or external AREF pin.
The first ADC conversion result after switching the reference voltage source may be inaccurate, and the user is advised to
discard this result.
18.7
ADC Noise Canceller
The ADC features a noise canceller that enables conversion during sleep mode to reduce noise induced from the CPU core
and other I/O peripherals. The noise canceller can be used with ADC noise reduction and idle modes. To make use of this
feature, the following procedure should be used:
a. Make sure that the ADC is enabled and is not busy converting. Single-conversion mode must be selected and the
ADC conversion complete interrupt must be enabled.
b.
Enter ADC noise reduction mode (or idle mode). The ADC will start a conversion once the CPU has been halted.
c.
If no other interrupts occur before the ADC conversion completes, the ADC interrupt will wake up the CPU and
execute the ADC conversion complete interrupt routine. If another interrupt wakes up the CPU before the ADC
conversion is complete, that interrupt will be executed, and an ADC conversion complete interrupt request will be
generated when the ADC conversion completes. The CPU will remain in active mode until a new sleep command
is executed.
Note that the ADC will not be automatically turned off when entering sleep modes other than idle mode or ADC noise
reduction mode. The user is advised to write logical zero to ADEN before entering such sleep modes to avoid excessive
power consumption.
124
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
18.7.1 Analog Input Circuitry
The analog input circuitry for single-ended channels is illustrated in Figure 18-8 on page 125. An analog source applied to
ADCn is subjected to the pin capacitance and input leakage of that pin, regardless of whether that channel is selected as
input for the ADC or not. When the channel is selected, the source must drive the S/H capacitor through the series
resistance (combined resistance in the input path).
The ADC is optimized for analog signals with an output impedance of approximately 10k or less. If such a source is used,
the sampling time will be negligible. If a source with higher impedance is used, the sampling time will depend on how long
the source needs to charge the S/H capacitor, with can vary widely. The user is recommended to only use low impedant
sources with slowly varying signals, since this minimizes the required charge transfer to the S/H capacitor.
Signal components higher than the nyquist frequency (fADC/2) should not be present to avoid distortion from unpredictable
signal convolution. The user is advised to remove high-frequency components with a low-pass filter before applying the
signals as inputs to the ADC.
Figure 18-8. Analog Input Circuitry
IIH
ADCn
1 to 100kΩ
IIL
CS/H = 14pF
VCC/2
18.7.2 Analog Noise Canceling Techniques
Digital circuitry inside and outside the device generates EMI which might affect the accuracy of analog measurements. If
conversion accuracy is critical, the noise level can be reduced by applying the following techniques:
a. Keep analog signal paths as short as possible. Make sure analog tracks run over the analog ground plane, and
keep them well away from high-speed switching digital tracks.
b.
Use the ADC noise canceller function to reduce induced noise from the CPU.
c.
If any port pins are used as digital outputs, it is essential that these do not switch while a conversion is in progress.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
125
18.7.3 ADC Accuracy Definitions
An n-bit single-ended ADC converts a voltage linearly between GND and VREF in 2n steps (LSBs). The lowest code is read
as 0, and the highest code is read as 2n–1.
Several parameters describe the deviation from the ideal behavior:
● Offset error: The deviation of the first transition (0x000 to 0x001) compared to the ideal transition (at 0.5LSB). Ideal
value: 0LSB.
Figure 18-9. Offset Error
Output Code
Ideal ADC
Actual ADC
Offset
Error
●
VREF Input Voltage
Gain error: After adjusting for offset, the gain error is found as the deviation of the last transition (0x3FE to 0x3FF)
compared to the ideal transition (at 1.5LSB below maximum). Ideal value: 0LSB
Figure 18-10. Gain Error
Output Code
Gain
Error
Ideal ADC
Actual ADC
VREF Input Voltage
126
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
●
Integral non-linearity (INL): After adjusting for offset and gain errors, the INL is the maximum deviation of an actual
transition compared to an ideal transition for any code. Ideal value: 0LSB.
Figure 18-11. Integral Non-linearity (INL)
INL
Output Code
Ideal ADC
Actual ADC
VREF Input Voltage
●
Differential non-linearity (DNL): The maximum deviation of the actual code width (the interval between two adjacent
transitions) from the ideal code width (1LSB). Ideal value: 0LSB.
Figure 18-12. Differential Non-linearity (DNL)
Output Code
0x3FF
1 LSB
DNL
0x000
0
VREF Input Voltage
●
Quantization error: Due to the quantization of the input voltage into a finite number of codes, a range of input voltages
(1LSB wide) will code to the same value. Always ±0.5LSB.
●
Absolute Accuracy: The maximum deviation of an actual (unadjusted) transition compared to an ideal transition for
any code. This is the compound effect of offset error, gain error, differential error, non-linearity, and quantization error.
Ideal value: ±0.5LSB.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
127
18.8
ADC Conversion Result
After the conversion is complete (ADIF is high), the conversion result can be found in the ADC result registers (ADCL,
ADCH). The form of the conversion result depends on the type of the conversion, as there are three types of conversion:
single-ended conversion, unipolar differential conversion and bipolar differential conversion.
18.8.1 Single Ended Conversion
For single ended conversion, the result is:
V IN  1024
ADC = --------------------------V REF
where VIN is the voltage on the selected input pin and VREF the selected voltage reference (see Table 18-3 on page 129 and
Table 18-4 on page 130). 0x000 represents analog ground, and 0x3FF represents the selected reference voltage minus
1LSB. The result is presented in one-sided form, from 0x3FF to 0x000.
18.8.2 Unipolar Differential Conversion
If differential channels and an unipolar input mode are used, the result is:
 V POS – V NEG   1024
ADC = --------------------------------------------------------  GAIN
V REF
where VPOS is the voltage on the positive input pin, VNEG the voltage on the negative input pin, and VREF the selected voltage
reference.
The voltage of the positive pin must always be larger than the voltage of the negative pin or otherwise the voltage difference
is saturated to zero. The result is presented in one-sided form, from 0x000 (0d) through 0x3FF (+1023d). The GAIN is either
1x or 20x.
18.8.3 Bipolar Differential Conversion
If differential channels and a bipolar input mode are used, the result is:
 V POS – V NEG   512
ADC = -----------------------------------------------------  GAIN
V REF
where VPOS is the voltage on the positive input pin, VNEG the voltage on the negative input pin, and VREF the selected voltage
reference. The result is presented in two’s complement form, from 0x200 (–512d) through 0x1FF (+511d). The GAIN is
either 1x or 20x. Note that if the user wants to perform a quick polarity check of the result, it is sufficient to read the MSB of
the result (ADC9 in ADCH). If the bit is one, the result is negative, and if this bit is zero, the result is positive.
As default the ADC converter operates in the unipolar input mode, but the bipolar input mode can be selected by writing the
BIN bit in the ADCSRB to one. In the bipolar input mode two-sided voltage differences are allowed and thus the voltage on
the negative input pin can also be larger than the voltage on the positive input pin.
18.9
Temperature Measurement
The temperature measurement is based on an on-chip temperature sensor that is coupled to a single-ended ADC8 channel.
Selecting the ADC8 channel by writing the MUX5:0 bits in the ADMUX register to “100010” enables the temperature sensor.
The internal 1.1V reference must also be selected for the ADC reference source in the temperature sensor measurement.
When the temperature sensor is enabled, the ADC converter can be used in single conversion mode to measure the voltage
over the temperature sensor. The measured voltage has a linear relationship to the temperature, as described in Table 18-2
on page 129. The voltage sensitivity is approximately 1mV/°C, and the accuracy of the temperature measurement is ±10°C
after offset calibration. Bandgap is always calibrated, and its accuracy is only guaranteed between 1.0V and 1.2V.
128
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 18-2. Temperature versus Sensor Output Voltage (Typical Case)
Temperature/°C
–40°C
+25°C
+85°C
+125°C
Voltage/mV
243mV
314mv
380mV
424mV
The values described in Table 18-2 are typical values. However, due to the process variation, the temperature sensor output
voltage varies from one chip to another. To be capable of achieving more accurate results, the temperature measurement
can be calibrated in the application software. The software calibration requires that a calibration value be measured and
stored in a register or EEPROM for each chip as a part of the production test. The software calibration can be done utilizing
the formula:
T = {[(ADCH << 8) | ADCL] - TOS} / k
where ADCn are the ADC data registers, k is a fixed coefficient and TOS is the temperature sensor offset value determined
and stored into EEPROM as a part of the production test.
To obtain best accuracy the coefficient k should be measured using two temperature calibrations. Using offset calibration,
set k = 1.0, where k = (1024  1.07mV/°C) /1.1V~1.0 [1/°C].
18.10 Register Description
18.10.1 ADMUX – ADC Multiplexer Selection Register
Bit
7
6
5
4
3
2
1
0
0x07 (0x27)
REFS1
REFS0
MUX5
MUX4
MUX3
MUX2
MUX1
MUX0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
ADMUX
• Bit 7:6 – REFS1:REFS0: Reference Selection Bits
These bits select the voltage reference for the ADC, as shown in Table 18-3. If these bits are changed during a conversion,
the change will not go in effect until this conversion is complete (ADIF in ADCSR is set).
Special care should be taken when changing differential channels. Once a differential channel has been selected, the stage
may take as much as 25 ADC clock cycles to stabilize to the new value. Thus conversions should not be started within the
first 13 clock cycles after selecting a new differential channel. Alternatively, conversion results obtained within this period
should be discarded.
The same settling time should be observed for the first differential conversion after changing ADC reference (by changing
the REFS1:0 bits in the ADMUX register).
For channels where differential gain is used (i.e., the gain stage), using VCC or an optional external AREF higher than
(VCC – 1V) is not recommended, as this will affect ADC accuracy. The internal voltage reference may not be connected to
the AREF pin if an external voltage is already being applied to it. The internal voltage reference is connected to the AREF pin
when REFS1:0 is set to the value “11”.
Table 18-3. Voltage Reference Selections for ADC
REFS1
REFS0
Voltage Reference Selection
0
0
VCC used as analog reference, disconnected from PA0 (AREF).
0
1
External voltage reference at PA0 (AREF) pin, internal voltage reference turned off.
1
0
Internal 1.1V voltage reference.
1
1
Reserved.
• Bits 5:0 – MUX5:0: Analog Channel and Gain Selection Bits
The value of these bits selects which combination of analog inputs are connected to the ADC. In the case of differential
input, gain selection is also made with these bits. Selections on Table 18-4 on page 130 show values for single-ended
channels and where the differential channels and the offset calibration selections are located. Selecting the single-ended
channel ADC8 enables the temperature measurement. See Table 18-4 on page 130 ffor details. If these bits are changed
during a conversion, the change will not go into effect until this conversion is complete (ADIF in ADCSRA is set).
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
129
Table 18-4. Single Ended Input Channel Selections.
Single Ended Input
MUX5..0
ADC0 (PA0)
000000
ADC1 (PA1)
000001
ADC2 (PA2)
000010
ADC3 (PA3)
000011
ADC4 (PA4)
000100
ADC5 (PA5)
000101
ADC6 (PA6)
000110
ADC7 (PA7)
000111
Reserved for differential channels
(1)
001000 - 011111
0V (AGND)
100000
1.1V (I Ref)
100001
ADC8(2)
Reserved for offset calibration
Notes:
100010
(3)
100011 - 100111
(1)
1.
Reserved for reversal differential channels
See Table 18-5 on page 131 for details.
101000 - 111111
2.
Section 18.9 “Temperature Measurement” on page 128
3.
For offset calibration only.See Table 18-5 on page 131 and Section 18.3 “ADC Operation” on page 120
See Table 18-5 on page 131 for details of selection of differential input channels as well as selection of offset calibration
channels. The MUX0 bit works as a gain selection bit for differential channels, as shown in Table 18-5 on page 131. When
the MUX0 bit is cleared (zero) 1x gain is selected, and when it is set (one) 20x gain is selected. For normal differential
channel pairs, the MUX5 bit works as a polarity reversal bit. Toggling of the MUX5 bit reverses the positive and negative
channel orientation.
For offset calibration purposes, the offset of certain differential channels can be measured by selecting the same input for
both negative and positive input. This calibration can be done for ADC0, ADC3, and ADC7. Section 18.3 “ADC Operation” on
page 120 describes offset calibration in a more detailed manner.
130
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 18-5. Differential Input channel Selections.
MUX5..0
Positive Differential Input
Negative Differential Input
Gain 1x
Gain 20x
N/A
100011
ADC1 (PA1)
001000
001001
ADC3 (PA3)
001010
001011
ADC0 (PA0)
101000
101001
ADC2 (PA2)
001100
001101
(1)
ADC0 (PA0)
ADC0 (PA0)
ADC1 (PA1)
ADC2 (PA2)
ADC3 (PA3)
ADC4 (PA4
ADC5 (PA5)
ADC6 (PA6)
ADC7 (PA7)
Note:
1.
ADC3 (PA3)
001110
001111
ADC1 (PA1)
101100
101101
ADC3 (PA3)
010000
010001
ADC0 (PA0)
101010
101011
ADC1 (PA1)
101110
101111
ADC2 (PA2)
110000
110001
ADC3 (PA3)(1)
100100
100101
ADC4 (PA4
010010
010011
ADC5 (PA5)
010100
010101
ADC6 (PA6)
010110
010111
ADC7 (PA7)
011000
011001
ADC3 (PA3)
110010
110011
ADC5 (PA5)
011010
011011
ADC3 (PA3)
110100
110101
ADC4 (PA4)
111010
111011
ADC6 (PA6)
011100
011101
ADC3 (PA3)
110110
110111
ADC5 (PA5)
111100
111101
ADC7 (PA7)
011110
011111
ADC3 (PA3)
111000
111001
ADC6 (PA6)
111110
ADC7 (PA7)(1)
100110
For offset calibration only.See Section 18.3 “ADC Operation” on page 120
111111
100111
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
131
18.10.2 ADCSRA – ADC Control and Status Register A
Bit
7
6
5
4
3
2
1
0
0x06 (0x26)
ADEN
ADSC
ADATE
ADIF
ADIE
ADPS2
ADPS1
ADPS0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
ADCSRA
• Bit 7 – ADEN: ADC Enable
Writing this bit to logical one enables the ADC. By writing it to zero, the ADC is turned off. Turning the ADC off while a
conversion is in progress will terminate the conversion.
• Bit 6 – ADSC: ADC Start Conversion
In single-conversion mode, write this bit to logical one to start each conversion. In free running mode, write this bit to logical
one to start the first conversion. The first conversion after ADSC has been written and after the ADC has been enabled, or if
ADSC is written at the same time as the ADC is enabled, will take 25 ADC clock cycles instead of the normal 13. This first
conversion initializes the ADC.
ADSC will read as one as long as a conversion is in progress. When the conversion is complete, it returns to zero. Writing
logical zero to this bit has no effect.
• Bit 5 – ADATE: ADC Auto Trigger Enable
When this bit is written to logical one, auto triggering of the ADC is enabled. The ADC will start a conversion on a positive
edge of the selected trigger signal. The trigger source is selected by setting the ADC trigger select bits (ADTS in ADCSRB).
• Bit 4 – ADIF: ADC Interrupt Flag
This bit is set when an ADC conversion completes and the data registers are updated. The ADC conversion complete
interrupt is executed if the ADIE bit and the I-bit in SREG are set. ADIF is cleared by hardware when executing the
corresponding interrupt handling vector. Alternatively, ADIF is cleared by writing a logical one to the flag. Beware that if
performing a read-modify-write on ADCSRA, a pending interrupt can be disabled. This also applies if the SBI instruction is
used.
• Bit 3 – ADIE: ADC Interrupt Enable
When this bit is written to logical one and the I-bit in SREG is set, the ADC conversion complete interrupt is activated.
• Bits 2:0 – ADPS2:0: ADC Prescaler Select Bits
These bits determine the division factor between the system clock frequency and the input clock to the ADC.
Table 18-6. ADC Prescaler Selections
132
ADPS2
ADPS1
ADPS0
Division Factor
0
0
0
2
0
0
1
2
0
1
0
4
0
1
1
8
1
0
0
16
1
0
1
32
1
1
0
64
1
1
1
128
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
18.10.3 ADCL and ADCH – ADC Data Register
18.10.3.1 ADLAR = 0
Bit
15
14
13
12
11
10
9
8
0x05 (0x25)
–
–
–
–
–
–
ADC9
ADC8
ADCH
0x04 (0x24)
ADC7
ADC6
ADC5
ADC4
ADC3
ADC2
ADC1
ADC0
ADCL
7
6
5
4
3
2
1
0
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read/Write
Initial Value
18.10.3.2 ADLAR = 1
Bit
15
14
13
12
11
10
9
8
0x05 (0x25)
ADC9
ADC8
ADC7
ADC6
ADC5
ADC4
ADC3
ADC2
ADCH
0x04 (0x24)
ADC1
ADC0
–
–
–
–
–
–
ADCL
7
6
5
4
3
2
1
0
Read/Write
Initial Value
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
When an ADC conversion is complete, the result is found in these two registers.
When ADCL is read, the ADC data register is not updated until ADCH is read. Consequently, if the result is left adjusted and
no more than 8-bit precision is required, it is sufficient to read ADCH. Otherwise, ADCL must be read first, then ADCH.
The ADLAR bit in ADCSRB, and the MUXn bits in ADMUX affect the way the result is read from the registers. If ADLAR is
set, the result is left adjusted. If ADLAR is cleared (default), the result is right adjusted.
• ADC9:0: ADC Conversion Result
These bits represent the result from the conversion, as detailed in Section 18.8 “ADC Conversion Result” on page 128.
18.10.4 ADCSRB – ADC Control and Status Register B
Bit
7
6
5
4
3
2
1
0
0x03 (0x23)
BIN
ACME
–
ADLAR
–
ADTS2
ADTS1
ADTS0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
ADCSRB
• Bits 7 – BIN: Bipolar Input Mode
The gain stage is working in the unipolar mode by default, but the bipolar mode can be selected by writing the BIN bit in the
ADCSRB register. In the unipolar mode, only one-sided conversions are supported, and the voltage on the positive input
must always be larger than the voltage on the negative input. Otherwise, the result is saturated to the voltage reference. In
the bipolar mode, two-sided conversions are supported, and the result is represented in two's complement form. In unipolar
mode, the resolution is 10 bits, and in bipolar mode the resolution is 9 bits + 1 sign bit.
• Bit 6 – ACME: Analog Comparator Multiplexer Enable
See Section 17.2.1 “ADCSRB – ADC Control and Status Register B” on page 116.
• Bit 5 – Res: Reserved Bit
This bit is reserved bit in the Atmel® ATtiny24/44/84, and will always read as what was written there.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
133
• Bit 4 – ADLAR: ADC Left Adjust Result
The ADLAR bit affects the presentation of the ADC conversion result in the ADC data register. Write logical one to ADLAR to
left adjust the result. Otherwise, the result is right adjusted. Changing the ADLAR bit will affect the ADC data register
immediately, regardless of any ongoing conversions. For a complete description of this bit, see Section 18.10.3 “ADCL and
ADCH – ADC Data Register” on page 133.
• Bit 3 – Res: Reserved Bit
This bit is reserved bit in the Atmel® ATtiny24/44/84, and will always read as what was written there.
• Bits 2:0 – ADTS2:0: ADC Auto Trigger Source
If ADATE in ADCSRA is written to logical one, the value of these bits selects which source will trigger an ADC conversion. If
ADATE is cleared, the ADTS2:0 settings will have no effect. A conversion will be triggered by the rising edge of the selected
interrupt flag. Note that switching from a trigger source that is cleared to a trigger source that is set will generate a positive
edge on the trigger signal. If ADEN in ADCSRA is set, this will start a conversion. Switching to free running mode
(ADTS[2:0]=0) will not cause a trigger event, even if the ADC interrupt flag is set.
Table 18-7. ADC Auto Trigger Source Selections
ADTS2
ADTS1
ADTS0
Trigger Source
0
0
0
Free running mode
0
0
1
Analog comparator
0
1
0
External interrupt request 0
0
1
1
Timer/Counter0 compare match A
1
0
0
Timer/Counter0 overflow
1
0
1
Timer/Counter1 compare match B
1
1
0
Timer/Counter1 overflow
1
1
1
Timer/Counter1 capture event
18.10.5 DIDR0 – Digital Input Disable Register 0
Bit
7
6
5
4
3
2
1
0
0x01 (0x21)
ADC7D
ADC6D
ADC5D
ADC4D
ADC3D
ADC2D
ADC1D
ADC0D
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
DIDR0
• Bits 7..0 – ADC7D..ADC0D: ADC7..0 Digital Input Disable
When this bit is written logical one, the digital input buffer on the corresponding ADC pin is disabled. The corresponding PIN
register bit will always read as zero when this bit is set. When an analog signal is applied to the ADC7..0 pin and the digital
input from this pin is not needed, this bit should be written logical one to reduce power consumption in the digital input buffer.
134
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
19.
debugWIRE On-chip Debug System
19.1
Features
●
●
●
●
●
●
●
●
●
●
19.2
Complete program flow control
Emulates all on-chip functions, both digital and analog, except RESET pin
Real-time operation
Symbolic debugging support (both at C and assembler source level, or for other HLLs)
Unlimited number of program break points (using software break points)
Non-intrusive operation
Electrical characteristics identical to real device
Automatic configuration system
High-speed operation
Programming of non-volatile memories
Overview
The debugWIRE on-chip debug system uses a one-wire, bi-directional interface to control the program flow, execute AVR®
instructions in the CPU and to program the different non-volatile memories.
19.3
Physical Interface
When the debugWIRE Enable (DWEN) fuse is programmed and Lock bits are unprogrammed, the debugWIRE system
within the target device is activated. The RESET port pin is configured as a wire-AND (open-drain) bi-directional I/O pin with
pull-up enabled and becomes the communication gateway between target and emulator.
Figure 19-1. The debugWIRE Setup
1.8 - 5.5V
VCC
dw
dw(RESET)
GND
Figure 19-1 shows the schematic of a target MCU, with debugWIRE enabled, and the emulator connector. The system clock
is not affected by debugWIRE and will always be the clock source selected by the CKSEL fuses.
When designing a system where debugWIRE will be used, the following observations must be made for correct operation:
● Pull-up resistor on the dW/(RESET) line must be in the range of 10k to 20k. However, the pull-up resistor is optional.
●
●
●
Connecting the RESET pin directly to VCC will not work.
Capacitors inserted on the RESET pin must be disconnected when using debugWire.
All external reset sources must be disconnected.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
135
19.4
Software Break Points
debugWIRE supports program memory break points by the Atmel® AVR® BREAK instruction. Setting a break point in
AVR Studio® will insert a BREAK instruction in the program memory. The instruction replaced by the BREAK instruction will
be stored. When program execution is continued, the stored instruction will be executed before continuing from the program
memory. A break can be inserted manually by putting the BREAK instruction in the program.
The flash must be re-programmed each time a break point is changed. This is automatically handled by AVR Studio through
the debugWIRE interface. The use of break points will there- fore reduce the flash data retention. Devices used for
debugging purposes should not be shipped to end customers.
19.5
Limitations of debugWIRE
The debugWIRE communication pin (dW) is physically located on the same pin as the external reset (RESET). An external
reset source is, therefore, not supported when the debugWIRE is enabled.
The debugWIRE system accurately emulates all I/O functions when running at full speed, i.e., when the program in the CPU
is running. When the CPU is stopped, care must be taken while accessing some of the I/O registers via the debugger (AVR
Studio). See the debugWIRE documentation for a detailed description of the limitations.
A programmed DWEN fuse enables some parts of the clock system to be running in all sleep modes. This will increase the
power consumption while in sleep. Thus, the DWEN fuse should be disabled when debugWire is not used.
19.6
Register Description
The following section describes the registers used with the debugWire system.
19.6.1 DWDR – debugWire Data Register
Bit
7
6
5
0x27 (0x47)
4
3
2
1
0
DWDR[7:0]
DWDR
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
The debugWire data register (DWDR) provides a communication channel from the program running in the MCU to the
debugger. This register is only accessible by the debugWIRE system, and can, therefore, not be used as a general purpose
register in normal operations.
136
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
20.
Self-Programming the Flash
The device provides a self-programming mechanism (SPM) for downloading and uploading program code by the MCU itself.
The self programming can use any available data interface and associated protocol to read code and write (program) that
code into program memory.
Program memory is updated in a page-by-page fashion. Before programming a page with the data stored in the temporary
page buffer, the page must be erased. The temporary page buffer is filled one word at a time using SPM, and the buffer can
be filled either before the page erase command or between a page erase and a page write operation:
Alternative 1 - fill the buffer before a page erase
● Fill the temporary page buffer
●
●
Perform a page erase
Perform a page write
Alternative 2 - fill the buffer after a page erase
● Perform a page erase
●
●
Fill the temporary page buffer
Perform a page write
If only a part of the page needs to be changed, the rest of the page must be stored (for example in the temporary page
buffer) before the erase, and then be re-written. When using alternative 1, the boot loader provides an effective
read-modify-write feature, which allows the user software to first read the page and do the necessary changes, and then
write back the modified data. If alternative 2 is used, it is not possible to read the old data while loading because the page is
already erased. The temporary page buffer can be accessed in a random sequence. It is essential that the page address
used in both the page erase and page write operation is addressing the same page.
20.1
Performing Page Erase by SPM
To execute a page erase, set up the address in the Z-pointer, write “00000011” to SPMCSR, and execute SPM within four
clock cycles after writing SPMCSR. The data in R1 and R0 are ignored. The page address must be written to PCPAGE in the
Z-register. Other bits in the Z-pointer will be ignored during this operation.
The CPU is halted during the page erase operation.
20.2
Filling the Temporary Buffer (Page Loading)
To write an instruction word, set up the address in the Z-pointer and data in R1:R0, write “00000001” to SPMCSR and
execute SPM within four clock cycles after writing SPMCSR. The content of PCWORD in the Z-register is used to address
the data in the temporary buffer. The temporary buffer will auto-erase after a page write operation or by writing the CTPB bit
in SPMCSR. It is also erased after a system reset. Note that it is not possible to write more than one time to each address
without erasing the temporary buffer.
If the EEPROM is written in the middle of an SPM page load operation, all data loaded will be lost.
20.3
Performing a Page Write
To execute a page write, set up the address in the Z-pointer, write “00000101” to SPMCSR, and execute SPM within four
clock cycles after writing SPMCSR. The data in R1 and R0 are ignored. The page address must be written to PCPAGE.
Other bits in the Z-pointer must be written to zero during this operation.
The CPU is halted during the page write operation.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
137
20.4
Addressing the Flash During Self-Programming
The Z-pointer is used to address the SPM commands.
Bit
15
14
13
12
11
10
9
8
ZH (R31)
Z15
Z14
Z13
Z12
Z11
Z10
Z9
Z8
ZL (R30)
Z7
Z6
Z5
Z4
Z3
Z2
Z1
Z0
7
6
5
4
3
2
1
0
Because the flash is organized in pages (see Table 21-7 on page 144), the program counter can be treated as having two
different sections. One section, consisting of the least significant bits, is addressing the words within a page, while the most
significant bits are addressing the pages. This is shown in Figure 21-1 on page 144. Note that the page erase and page write
operations are addressed independently. Therefore it is of major importance that the software addresses the same page in
both the page erase and page write operation.
The LPM instruction uses the Z-pointer to store the address. Because this instruction addresses the flash byte-by-byte, the
LSB (bit Z0) of the Z-pointer is also used.
Figure 20-1. Addressing the Flash During SPM(1)
Bit
15
ZPCMSB
ZPAGEMSB
Z-register
1 0
0
PCMSB
Program
Counter
PAGEMSB
PCPAGE
Page Address
within the Flash
PCWORD
Word Address
within a Page
Program Memory
Page
Page
Instruction Word
PCWORD[PAGEMSB:0]
00
01
02
PAGEEND
Note:
1.
The different variables used in Figure 20-1 are listed in Table 21-7 on page 144.
20.4.1 EEPROM Write Prevents Writing to SPMCSR
Note that an EEPROM write operation will block all software programming to flash. Reading the fuses and lock bits from
software will also be prevented during the EEPROM write operation. It is recommended that the user check the status bit
(EEPE) in the EECR register and verify that the bit is cleared before writing to SPMCSR.
138
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
20.4.2 Reading the Lock and Fuse Bits from Software
It is possible to read both the lock and fuse bits from software. To read the lock bits, load the Z-pointer with 0x0001 and set
the RFLB and SPMEN bits in SPMCSR. When an LPM instruction is executed within three CPU cycles after the RFLB and
SPMEN bits are set in SPMCSR, the value of the lock bits will be loaded in the destination register. The RFLB and SPMEN
bits will auto-clear upon completion of reading the lock bits, or if no LPM instruction is executed within three CPU cycles, or if
no SPM instruction is executed within four CPU cycles. When RFLB and SPMEN are cleared, LPM will work as described in
the instruction set summary.
Bit
7
6
5
4
3
2
1
0
Rd
–
–
–
–
–
–
LB2
LB1
The algorithm for reading the fuse low byte (FLB) is similar to the one described above for reading the lock bits. To read the
fuse low byte, load the Z-pointer with 0x0000 and set the RFLB and SPMEN bits in SPMCSR. When an LPM instruction is
executed within three cycles after the RFLB and SPMEN bits are set in the SPMCSR, the value of the fuse low byte will be
loaded in the destination register as shown below. See Table 21-5 on page 143 for a detailed description and mapping of the
fuse low byte.
Bit
7
6
5
4
3
2
1
0
Rd
FLB7
FLB6
FLB5
FLB4
FLB3
FLB2
FLB1
FLB0
Similarly, when reading the fuse high byte (FHB), load 0x0003 in the Z-pointer. When an LPM instruction is executed within
three cycles after the RFLB and SPMEN bits are set in the SPMCSR, the value of the fuse high byte will be loaded in the
destination register as shown below. See Table 21-4 on page 142 for detailed description and mapping of the fuse high byte.
Bit
7
6
5
4
3
2
1
0
Rd
FHB7
FHB6
FHB5
FHB4
FHB3
FHB2
FHB1
FHB0
Lock and fuse bits that are programmed will be read as zero. Lock and fuse bits that are unprogrammed, will be read as one.
20.4.3 Preventing Flash Corruption
During periods of low VCC, the flash program can be corrupted because the supply voltage is too low for the CPU and the
flash to operate properly. These issues are the same as for board-level systems using flash, and the same design solutions
should be applied.
Flash program corruption can occur for two reasons when the voltage is too low. First, a regular write sequence to the flash
requires a minimum voltage to operate correctly. Secondly, the CPU itself can execute instructions incorrectly if the supply
voltage is too low.
Flash corruption can easily be avoided by following at least one these design recommendations:
1. Keep the Atmel® AVR® RESET active (low) during periods of insufficient power supply voltage. This can be done
by enabling the internal brown-out detector (BOD) if the operating voltage matches the detection level. If not, an
external low VCC reset protection circuit can be used. If a reset occurs while a write operation is in progress, the
write operation will be completed provided the power supply voltage is sufficient.
2.
Keep the AVR core in power-down sleep mode during periods of low VCC. This will prevent the CPU from
attempting to decode and execute instructions, effectively protecting SPMCSR and, thus, the flash from
unintentional writes.
20.4.4 Programming Time for Flash when Using SPM
The calibrated RC oscillator is used to time flash accesses. Table 20-1 shows the typical programming time for flash
accesses from the CPU.
Table 20-1. SPM Programming Time(1)
Symbol
Min Programming Time
Flash write (page erase, page write, and write lock
3.7 ms
bits by SPM)
Note:
1. The min and max programming times are per individual operation.
Max Programming Time
4.5 ms
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
139
20.5
Register Description
20.5.1 SPMCSR – Store Program Memory Control and Status Register
The store program memory control and status register contains the control bits needed to control program memory
operations.
Bit
7
6
5
4
3
2
1
0
0x37 (0x57)
–
–
–
CTPB
RFLB
PGWRT
PGERS
SPMEN
Read/Write
R
R
R
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
SPMCSR
• Bits 7..5 – Res: Reserved Bits
These bits are reserved bits in the Atmel®ATtiny24/44/84 and always read as zero.
• Bit 4 – CTPB: Clear Temporary Page Buffer
If the CTPB bit is written while filling the temporary page buffer, the temporary page buffer will be cleared and the data will be
lost.
• Bit 3 – RFLB: Read Fuse and Lock Bits
An LPM instruction within three cycles after RFLB and SPMEN are set in SPMCSR will read either the lock bits or the fuse
bits (depending on Z0 in the Z-pointer) in the destination register. See Section 20.4.1 “EEPROM Write Prevents Writing to
SPMCSR” on page 138 for details.
• Bit 2 – PGWRT: Page Write
If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock cycles executes page write,
with the data stored in the temporary buffer. The page address is taken from the high part of the Z-pointer.
The data in R1 and R0 are ignored. The PGWRT bit will auto-clear upon completion of a page write, or if no SPM instruction
is executed within four clock cycles. The CPU is halted during the entire page write operation.
• Bit 1 – PGERS: Page Erase
If this bit is written to logical one at the same time as SPMEN, the next SPM instruction within four clock cycles executes a
page erase. The page address is taken from the high part of the Z-pointer. The data in R1 and R0 are ignored. The PGERS
bit will auto-clear upon completion of a page erase, or if no SPM instruction is executed within four clock cycles. The CPU is
halted during the entire page erase operation.
• Bit 0 – SPMEN: Store Program Memory Enable
This bit enables the SPM instruction for the next four clock cycles. If written to logical one together with either CTPB, RFLB,
PGWRT, or PGERS, the following SPM instruction will have a special meaning (see description above). If only SPMEN is
written, the following SPM instruction will store the value in R1:R0 in the temporary page buffer addressed by the Z-pointer.
The LSB of the Z-pointer is ignored. The SPMEN bit will auto-clear upon completion of an SPM instruction, or if no SPM
instruction is executed within four clock cycles. During page erase and page write, the SPMEN bit remains high until the
operation is completed.
Writing any combination other than “10001”, “01001”, “00101”, “00011”, or “00001” in the lower five bits will have no effect.
140
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
21.
Memory Programming
This section describes the different methods for programming the Atmel® ATtiny24/44/84 memories.
21.1
Program And Data Memory Lock Bits
The ATtiny24/44/84 provides two lock bits which can be left unprogrammed (set to one) or can be programmed (set to zero)
to obtain the additional security listed in Table 21-2. The lock bits can only be erased to one with the chip erase command.
Program memory can be read via the debugWIRE interface when the DWEN fuse is programmed even if the lock bits are
set. Thus, when lock bit security is required, debugWIRE should always be disabled by clearing the DWEN fuse.
Table 21-1. Lock Bit Byte(1)
Lock Bit Byte
Bit No
Description
Default Value
7
–
1 (unprogrammed)
6
–
1 (unprogrammed)
5
–
1 (unprogrammed)
4
–
1 (unprogrammed)
3
–
1 (unprogrammed)
2
–
1 (unprogrammed)
1
Lock bit
1 (unprogrammed)
LB1
0
Lock bit
“1” means unprogrammed, “0” means programmed.
1 (unprogrammed)
LB2
Note:
1.
Table 21-2. Lock Bit Protection Modes(1)(2)
Memory Lock Bits
Protection Type
LB Mode
LB2
LB1
1
1
1
No memory lock features enabled.
2
1
0
Further programming of the Flash and EEPROM is disabled in high-voltage
and serial programming mode. The fuse bits are locked in both serial and
high-voltage programming mode(1). debugWire is disabled.
1.
Further programming and verification of the Flash and EEPROM is disabled
in high-voltage and serial programming mode. The fuse bits are locked in
both serial and high-voltage programming mode(1). debugWire is disabled.
Program the fuse bits before programming LB1 and LB2.
2.
“1” means unprogrammed, “0” means programmed
3
Notes:
0
0
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
141
21.2
Fuse Bytes
The Atmel ATtiny24/44/84 has three fuse bytes. Table 21-4 to Table 21-5 describe briefly the functionality of all the fuses and
how they are mapped into the fuse bytes. Note that the fuses are read as logical zero (“0”) if they are programmed.
Table 21-3. Fuse Extended Byte
Fuse High Byte
Bit No
Description
Default Value
7
-
1 (unprogrammed)
6
-
1 (unprogrammed)
5
-
1 (unprogrammed)
4
-
1 (unprogrammed)
3
-
1 (unprogrammed)
2
-
1 (unprogrammed)
1
-
1 (unprogrammed)
0
Self programming enable
1 (unprogrammed)
SELFPRGEN
Table 21-4. Fuse High Byte
Fuse High Byte
RSTDISBL
(1)
Bit No
Description
Default Value
7
External reset disable
1 (unprogrammed)
(2)
DWEN
6
DebugWIRE enable
1 (unprogrammed)
SPIEN(3)
6
Enable serial program and data downloading
0 (programmed, SPI prog.
enabled)
WDTON(4)
4
Watchdog timer always on
1 (unprogrammed)
EESAVE
3
EEPROM memory is preserved through the chip 1 (unprogrammed, EEPROM
erase
not preserved)
BODLEVEL2(5)
2
Brown-out detector trigger level
1 (unprogrammed)
(5)
1
Brown-out detector trigger level
1 (unprogrammed)
BODLEVEL1
(5)
BODLEVEL0
0
Brown-out detector trigger level
1 (unprogrammed)
Notes: 1. See Section 12.3.2 “Alternate Functions of Port B” on page 59 for description of RSTDISBL and DWEN fuses.
When programming the RSTDISBL fuse, high-voltage Serial programming has to be used to change fuses to
perform further programming
142
2.
DWEN must be unprogrammed when lock Bit security is required.
See Section 21.1 “Program And Data Memory Lock Bits” on page 141.
3.
The SPIEN Fuse is not accessible in SPI Programming mode.
4.
See Section 9-2 “WDT Configuration as a Function of the Fuse Settings of WDTON” on page 40 for details.
5.
See Table 22-5 on page 158 for BODLEVEL fuse decoding.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 21-5. Fuse Low Byte
Fuse Low Byte
Bit No
Description
Default Value
7
Divide clock by 8
0 (programmed)
CKOUT
6
Clock Output Enable
1 (unprogrammed)
SUT1
5
Select start-up time
1 (unprogrammed)(2)
SUT0
4
Select start-up time
0 (programmed)(2)
CKSEL3
3
Select Clock source
0 (programmed)(3)
CKSEL2
2
Select Clock source
0 (programmed)(3)
CKSEL1
1
Select Clock source
1 (unprogrammed)(3)
(1)
CKDIV8
Notes:
0 (programmed)(3)
CKSEL0
0
Select Clock source
1. See Section 7.9 “System Clock Prescaler” on page 29 for details.
2.
The default value of SUT1..0 results in maximum start-up time for the default clock source.
See Table 7-7 on page 27 for details.
3.
The default setting of CKSEL3..0 results in internal RC oscillator at 8.0MHz. See Table 7-6 on page 27 for
details.
The status of the fuse bits is not affected by chip erase. Note that the fuse bits are locked if lock bit 1 (LB1) is programmed.
Program the fuse bits before programming the lock bits.
21.2.1 Latching of Fuses
The fuse values are latched when the device enters programming mode, and changes in the fuse values will have no effect
until the part leaves programming mode. This does not apply to the EESAVE fuse, which will take effect once it is
programmed. The fuses are also latched on power-up in normal mode.
21.3
Signature Bytes
All Atmel® microcontrollers have a three-byte signature code that identifies the device. This code can be read in both serial
and high-voltage programming mode, even when the device is locked. The three bytes reside in a separate address space.
For the Atmel ATtiny24/44/84, the signature bytes are given in Table 21-6.
Table 21-6. Device ID
Signature Bytes Address
21.4
Device
0x000
0x001
0x002
ATtiny24
0x1E
0x91
0x0B
ATtiny44
0x1E
0x92
0x07
ATtiny84
0x1E
0x93
0x0C
Calibration Byte
The signature area of the Atmel ATtiny24/44/84 has one byte of calibration data for the internal RC oscillator. This byte
resides in the high byte of address 0x000. During reset, this byte is automatically written into the OSCCAL register to ensure
the correct frequency of the calibrated RC oscillator.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
143
21.5
Page Size
Table 21-7. No. of Words in a Page and No. of Pages in the Flash
Device
Flash Size
Page Size
PCWORD
No. of Pages
PCPAGE
PCMSB
ATtiny24
1Kwords
(2Kbytes)
16 words
PC[3:0]
64
PC[9:4]
9
ATtiny44
2Kwords
(4Kbytes)
32 words
PC[4:0]
64
PC[10:5]
10
ATtiny84
4Kwords
(8Kbytes)
32 words
PC[4:0]
128
PC[11:5]
11
Table 21-8. No. of Words in a Page and No. of Pages in the EEPROM
21.6
Device
EEPROM Size
Page Size
PCWORD
No. of Pages
PCPAGE
EEAMSB
ATtiny24
128 bytes
4 bytes
EEA[1:0]
32
EEA[6:2]
6
ATtiny44
256 bytes
4 bytes
EEA[1:0]
64
EEA[7:2]
7
ATtiny84
512 bytes
4 bytes
EEA[1:0]
128
EEA[8:2]
8
Serial Downloading
Both the flash and EEPROM memory arrays can be programmed using the serial SPI bus while RESET is pulled to GND.
The serial interface consists of pins SCK, MOSI (input) and MISO (output). After RESET is set low, the programming enable
instruction needs to be executed first before program/erase operations can be executed. NOTE, in Table 21-9, the pin
mapping for SPI programming is listed. Not all parts use the SPI pins dedicated for the internal SPI interface.
Figure 21-1. Serial Programming and Verify(1)
+1.8V to 5.5V
VCC
MOSI
MISO
SCK
RESET
GND
Note:
1.
If the device is clocked by the internal oscillator, it is not needed to connect a clock source to the CLKI pin.
Table 21-9. Pin Mapping Serial Programming
144
Symbol
Pins
I/O
Description
MOSI
PA6
I
Serial data in
MISO
PA5
O
Serial data out
SCK
PA4
I
Serial clock
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming operation (in serial mode
only), and there is no need to first execute the chip erase instruction. The chip erase operation turns the content of every
memory location in both the program and EEPROM arrays into 0xFF.
Depending on the CKSEL fuses, a valid clock must be present. The minimum low and high periods for the serial clock (SCK)
input are defined as follows:
Low:
> 2 CPU clock cycles for fck < 12MHz, 3 CPU clock cycles for fck ≥ 12MHz
High:
> 2 CPU clock cycles for fck < 12MHz, 3 CPU clock cycles for fck ≥ 12MHz
21.6.1 Serial Programming Algorithm
When writing serial data to the Atmel® AVR® ATtiny24/44/84, data are clocked on the rising edge of SCK.
When reading data from the Atmel ATtiny24/44/84, data are clocked on the falling edge of SCK. See Figure 22-3 on page
161 and Figure 22-4 on page 161 for timing details.
To program and verify the Atmel ATtiny24/44/84 in the serial programming mode, the following sequence is recommended
(see four-byte instruction formats in Table 21-11):
1. Power-up sequence:
Apply power between VCC and GND while RESET and SCK are set to “0”. In some systems, the programmer can
not guarantee that SCK is held low during power-up. In this case, RESET must be given a positive pulse of at
least two CPU clock cycles duration after SCK has been set to “0”.
2.
Wait for at least 20ms and enable serial programming by sending the Programming Enable serial instruction to pin
MOSI.
3.
The serial programming instructions will not work if the communication is out of synchronization. When in sync,
the second byte (0x53) will echo back when issuing the third byte of the programming enable instruction.
Regardless of whether the echo is correct or not, all four bytes of the instruction must be transmitted. If the 0x53
did not echo back, give RESET a positive pulse and issue a new programming enable command.
4.
The flash is programmed one page at a time. The memory page is loaded one byte at a time by supplying the five
LSBs of the address and data together with the load program memory page instruction. To ensure correct loading
of the page, the data low byte must be loaded before the data high byte is applied for a given address.
The program memory page is stored by loading the write program memory page instruction with the three MSBs
of the address. If polling (RDY/BSY) is not used, the user must wait at least tWD_FLASH before issuing the next
page. (See Table 21-10 on page 146.) Accessing the serial programming interface before the flash write operation
completes can result in incorrect programming.
5.
A: The EEPROM array is programmed one byte at a time by supplying the address and data together with the
appropriate write instruction. An EEPROM memory location is first automatically erased before new
data are written. If polling (RDY/BSY) is not used, the user must wait at least tWD_EEPROM before issuing the next
byte. (See Table 21-10 on page 146.) In a chip erased device, no 0xFFs in the data file(s)
need to be programmed.
B: The EEPROM array is programmed one page at a time. The memory page is loaded one byte at a time by
supplying the two LSBs of the address and data together with the Load EEPROM memory page instruction. The
EEPROM memory page is stored by loading the Write EEPROM memory page instruction with the four MSBs of
the address. When using EEPROM page access only byte locations loaded with the Load EEPROM memory
page instruction is altered. The remaining locations remain unchanged. If polling (RDY/BSY) is not used, the used
must wait at least tWD_EEPROM before issuing the next page (See Table 21-10 on page 146). In a chip-erased
device, no 0xFF in the data file(s) need to be programmed.
6.
Any memory location can be verified by using the read instruction which returns the content at the selected
address at serial output MISO.
7.
At the end of the programming session, RESET can be set high to commence normal operation.
8.
Power-off sequence (if needed):
Set RESET to “1”.
Turn VCC power off.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
145
Table 21-10. Minimum Wait Delay Before Writing the Next Flash or EEPROM Location
Symbol
Minimum Wait Delay
tWD_FLASH
4.5ms
tWD_EEPROM
4.0ms
tWD_ERASE
4.0ms
tWD_FUSE
4.5ms
21.6.2 Serial Programming Instruction set
Table 21-11 and Figure 21-2 on page 148 describes the Instruction set.
Table 21-11. Serial Programming Instruction Set
Instruction Format
(1)
Instruction/Operation
Byte 1
Byte 2
Byte 3
Byte4
Programming enable
$AC
$53
$00
$00
Chip erase (program memory/EEPROM)
$AC
$80
$00
$00
Poll RDY/BSY
$F0
$00
$00
data byte out
Load Instructions
Load extended address byte
$4D
$00
Extended adr
$00
Load program memory page, high byte
$48
adr MSB
adr LSB
high data byte in
Load program memory page, low byte
$40
adr MSB
adr LSB
low data byte in
Load EEPROM memory Page (page
access)
$C1
$00
adr LSB
data byte in
Read program memory, high byte
$28
adr MSB
adr LSB
high data byte out
Read program memory, low byte
$20
adr MSB
adr LSB
low data byte out
Read EEPROM memory
$A0
$00
adr LSB
data byte out
Read lock bits
$58
$00
$00
data byte out
Read signature byte
$30
$00
adr LSB
data byte out
Read fuse bits
$50
$00
$00
data byte out
Read fuse high bits
$58
$08
$00
data byte out
Read extended fuse bits
$50
$08
$00
data byte out
$00
$00
data byte out
Read Instructions
Read calibration byte
$38
Notes: 1. Not all instructions are applicable for all parts.
146
2.
adr = address
3.
Bits are programmed ‘0’, unprogrammed ‘1’.
4.
To ensure future compatibility, unused fuses and lock bits should be unprogrammed (‘1’).
5.
Refer to the corresponding section for fuse and lock bits, calibration and signature bytes and page size.
6.
Instructions accessing program memory use a word address. This address may be random within the page
range.
7.
See http://www.atmel.com/avr for application notes regarding programming and programmers.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 21-11. Serial Programming Instruction Set (Continued)
Instruction Format
(1)
Instruction/Operation
Byte 1
Byte 2
Byte 3
Byte4
Write program memory page
$4C
adr MSB
adr LSB
$00
Write EEPROM memory
$C0
$00
adr LSB
data byte in
Write EEPROM memory Page (page
access)
$C2
$00
adr LSB
$00
Write lock bits
$AC
$E0
$00
data byte in
Write fuse bits
$AC
$A0
$00
data byte in
Write fuse high bits
$AC
$A8
$00
data byte in
$A4
$00
data byte in
Write Instructions(6)
Write extended fuse bits
$AC
Notes: 1. Not all instructions are applicable for all parts.
2.
adr = address
3.
Bits are programmed ‘0’, unprogrammed ‘1’.
4.
To ensure future compatibility, unused fuses and lock bits should be unprogrammed (‘1’).
5.
Refer to the corresponding section for fuse and lock bits, calibration and signature bytes and page size.
6.
Instructions accessing program memory use a word address. This address may be random within the page
range.
7.
See http://www.atmel.com/avr for application notes regarding programming and programmers.
If the LSB in RDY/BSY data byte out is ‘1’, a programming operation is still pending. Wait until this bit returns ‘0’ before the
next instruction is carried out.
Within the same page, the low data byte must be loaded prior to the high data byte.
After data are loaded to the page buffer, program the EEPROM page (see Figure 21-2 on page 148).
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
147
Figure 21-2. Serial Programming Instruction Example
Serial Programming Instruction
Load Program Memory Page (High/Low Byte)/
Load EEPROM Memory Page (page access)
Byte 1
Byte 2
Byte 3
Adr MBS
Adr LBS
Bit 15 B
Write Program Memory Page/
Write EEPROM Memory Page
Byte 4
Byte 1
0
Byte 2
Byte 3
Adr MBS
Adr LBS
Bit 15 B
Byte 4
0
Page Buffer
Page Offset
Page 0
Page 1
Page 2
Page Number
Page N-1
Program Memory/
EEPROM Memory
21.7
High-voltage Serial Programming
This section describes how to program and verify flash program memory, EEPROM data memory, lock bits and fuse bits in
the Atmel® ATtiny24/44/84.
Figure 21-3. High-voltage Serial Programming
+ 1.8 to 5.5V
+ 11.5 to 12.5V
SCI
PB3 (RESET)
VCC
PB0
PA4
SDO
PA5
SII
PA6
SDI
GND
148
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 21-12. Pin Name Mapping
Signal Name in High-voltage Serial
Programming Mode
Pin Name
I/O
SDI
PA6
I
Serial data input
Function
SII
PA5
I
Serial instruction input
SDO
PA4
O
Serial data output
SCI
PB0
I
Serial clock input (min. 220ns period)
The minimum period for the serial clock input (SCI) during high-voltage serial programming is 220ns.
Table 21-13. Pin Values Used to Enter Programming Mode
21.8
Pin
Symbol
Value
PA0
Prog_enable[0]
0
PA1
Prog_enable[1]
0
PA2
Prog_enable[2]
0
High-voltage Serial Programming Algorithm
To program and verify the Atmel® AVR® ATtiny24/44/84 in the high-voltage serial programming mode, the following
sequence is recommended (see instruction formats in Table 21-15 on page 152):
21.8.1 Enter High-voltage Serial Programming Mode
The following algorithm puts the device in high-voltage serial programming mode:
1. Apply 4.5 - 5.5V between VCC and GND.
2.
Set RESET pin to “0” and toggle SCI at least six times.
3.
Set the Prog_enable pins listed in Table 21-13 to “000” and wait at least 100ns.
4.
Apply VHVRST – 5.5V to RESET. Keep the Prog_enable pins unchanged for at least tHVRST after the high-voltage
has been applied to ensure the Prog_enable signature has been latched.
5.
Shortly after latching the Prog_enable signature, the device will actively output data on the Prog_enable[2]/SDO
pin, and the resulting drive contention may increase the power consumption. To minimize this drive contention,
release the Prog_enable[2] pin after tHVRST has elapsed.
6.
Wait at least 50µs before giving any serial instructions on SDI/SII.
Table 21-14. High-voltage Reset Characteristics
Supply Voltage
RESET Pin High-voltage Threshold
Minimum High-voltage Period for Latching
Prog_enable
VCC
VHVRST
tHVRST
4.5V
11.5V
100ns
5.5V
11.5V
100ns
21.8.2 Considerations for Efficient Programming
The loaded command and address are retained in the device during programming. For efficient programming, the following
should be considered.
● The command needs only be loaded once when writing or reading multiple memory locations.
●
Skip writing the data value 0xFF that is the contents of the entire EEPROM (unless the EESAVE fuse is programmed)
and flash after a chip erase.
●
Address high byte only needs be loaded before programming or reading a new 256-word window in flash or 256-byte
EEPROM. This consideration also applies to reading signature bytes.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
149
21.8.3 Chip Erase
The chip erase will erase the flash and EEPROM(1) memories, as well as lock bits. The lock bits are not reset until the
program memory has been completely erased. The fuse bits are not changed. A chip erase must be performed before the
flash and/or EEPROM are reprogrammed.
Note:
1.
The EEPROM memory is preserved during chip erase if the EESAVE fuse is programmed.
1.
Load “chip erase” command (see Table 21-15 on page 152).
2.
Wait after Instr. 3 until SDO goes high for the “chip erase” cycle to finish.
3.
Load “no operation” command.
21.8.4 Programming the Flash
The flash is organized in pages, see Section 21.5 “Page Size” on page 144. When programming the flash, the program data
are latched into a page buffer. This allows one page of program data to be programmed simultaneously. The following
procedure describes how to program the entire flash memory:
1. Load “write flash” command (see Table 21-15 on page 152).
2.
Load flash page buffer.
3.
Load flash high address and program page. Wait after Instr. 3 until SDO goes high for the “page programming”
cycle to finish.
4.
Repeat 2 and 3 until the entire flash is programmed, or until all data has been programmed.
5.
End page programming by loading “no operation” command.
When writing or reading serial data to the Atmel® ATtiny24/44/84, data are clocked on the rising edge of the serial clock. See
Figure 22-5 on page 162, Figure 21-3 on page 148 and Table 22-9 on page 162 for details.
Figure 21-4. Addressing the Flash which is Organized in Pages
PCMSB
Program
Counter
PAGEMSB
PCPAGE
Page Address
within the Flash
PCWORD
Word Address
within a Page
Program Memory
Page
Page
Instruction Word
PCWORD[PAGEMSB:0]
00
01
02
PAGEEND
150
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Figure 21-5. High-voltage Serial Programming Waveforms
SDI
PB0
MSB
LSB
SII
PB1
MSB
LSB
SDO
PB2
SCI
PB3
MSB
0
LSB
1
2
3
4
5
6
7
8
9
10
21.8.5 Programming the EEPROM
The EEPROM is organized in pages, see Table 22-8 on page 161. When programming the EEPROM, the data are latched
into a page buffer. This allows one page of data to be programmed simultaneously. The programming algorithm for the
EEPROM data memory is as follows (refer to Table 21-15 on page 152):
1. Load “Write EEPROM” command.
2.
Load EEPROM page buffer.
3.
Program EEPROM page. Wait after Instr. 2 until SDO goes high for the page programming cycle to finish.
4.
Repeat 2 and 3 until the entire EEPROM is programmed, or until all data has been programmed.
5.
End page programming by loading “no operation” command.
21.8.6 Reading the Flash
The algorithm for reading the flash memory is as follows (refer to Table 21-15 on page 152):
1. Load “read flash” command.
2.
Read flash low and high bytes. The contents at the selected address are available at serial output SDO.
21.8.7 Reading the EEPROM
The algorithm for reading the EEPROM memory is as follows (refer to Table 21-15 on page 152):
1. Load “read EEPROM” command.
2.
Read EEPROM byte. The contents at the selected address are available at serial output SDO.
21.8.8 Programming and Reading the Fuse and Lock Bits
The algorithms for programming and reading the fuse low/high bits and lock bits are shown in Table 21-15 on page 152.
21.8.9 Reading the Signature Bytes and Calibration Byte
The algorithms for reading the signature bytes and calibration byte are shown in Table 21-15 on page 152.
21.8.10 Power-off sequence
Set SCI to “0”. Set RESET to “1”. Turn VCC power off.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
151
Table 21-15. High-voltage Serial Programming Instruction Set for ATtiny24/44/84
Instruction Format
Instruction
Instr.1/5
Instr.2/6
Instr.4
Chip erase
Load “write
flash”
Command
SDI
SII
SDO
0_0001_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
SDI
SII
SDO
0_ bbbb_bbbb _00 0_eeee_eeee_00
0_0000_1100_00
0_0010_1100_00
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1101_00
x_xxxx_xxxx_xx
SDI
SII
SDO
0_dddd_dddd_00
0_0011_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
x_xxxx_xxxx_xx
Instr 5-7.
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
Wait after Instr 3 until SDO
goes high. Repeat Instr. 2 - 3
for each loaded flash page
until the entire flash or all data
are programmed. Repeat Instr.
1 for a new 256-byte page(1).
0_0000_0000_00
0_0111_1101_00
x_xxxx_xxxx_xx
SDI
SII
SDO
0_0000_000a_00
0_0001_1100_00
x_xxxx_xxxx_xx
Load “read
flash”
command
SDI
SII
SDO
0_0000_0010_00
0_0100_1100_00
x_xxxx_xxxx_xx
SDI
SII
SDO
0_bbbb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
0_0000_000a_00
0_0001_1100_00
x_xxxx_xxxx_xx
SDI
SII
SDO
0_0000_0000_00
0_0111_1000_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
p_pppp_pppx_xx
SDI
SII
SDO
0_0001_0001_00
0_0100_1100_00
x_xxxx_xxxx_xx
SDI
SII
SDO
0_bbbb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
SDI
SII
SDO
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
SDI
SII
SDO
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
Load “write
EEPROM”
Command
Load
EEPROM
Page buffer
Program
EEPROM
page
Wait after Instr.3 until SDO
goes high for the chip erase
cycle to finish.
Enter flash programming code.
Load flash
High address
and program
page
Read flash
Low and high
bytes
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
Operation Remarks
0_1000_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
Load flash
Page buffer
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
Instr.3/7
SDI
SII
SDO
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
Repeat after Instr. 1 - 7until the
entire page buffer is filled or
until all data within the page is
filled(1).
Enter flash read mode.
0_0000_0000_00
0_0110_1000_00
x_xxxx_xxxx_xx
0_0000_0000_00 Repeat Instr. 1, 3 - 6 for each
0_0110_1100_00 new address. Repeat Instr. 2
q_qqqq_qqqx_xx for a new 256 byte page.
Instr 5 - 6.
Enter EEPROM programming
mode.
0_aaaa_aaaa_00
0_0001_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
0_eeee_eeee_00
0_0010_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1101_00
x_xxxx_xxxx_xx
Repeat Instr. 1 - 5 until the
entire page buffer is filled or
until all data within the page is
filled(2).
Wait after Instr. 2 until SDO
goes high. Repeat Instr. 1 - 2
for each loaded EEPROM
page until the entire EEPROM
or all data is programmed.
a = address high bits, b = address low bits, d = data in high bits, e = data in low bits, p = data out high bits,
q = data out low bits, x = don’t care, 1 = Lock Bit1, 2 = Lock Bit2, 3 = CKSEL0 Fuse, 4 = CKSEL1 Fuse, 5 = CKSEL2 Fuse,
6 = CKSEL3 Fuse, 7 = SUT0 Fuse, 8 = SUT1 Fuse, 9 = CKDIV8 Fuse, A = CKOUT Fuse, B = BODLEVEL0 Fuse,
C = BODLEVEL1 Fuse, D= BODLEVEL2 Fuse, E = EESAVE Fuse, F = WDTON Fuse, G = SPIEN Fuse, H = DWEN Fuse,
I = RSTDISBL Fuse
Notes:
152
1.
For page sizes less than 256 words, parts of the address (bbbb_bbbb) will be parts of the page address.
2.
For page sizes less than 256 bytes, parts of the address (bbbb_bbbb) will be parts of the page address.
3.
The EEPROM is written page-wise. But only the bytes that are loaded into the page are actually written to the
EEPROM. Page-wise EEPROM access is more efficient when multiple bytes are to be written to the same
page. Note that auto-erase of EEPROM is not available in high-voltage serial programming, only in SPI
programming.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 21-15. High-voltage Serial Programming Instruction Set for ATtiny24/44/84 (Continued)
Instruction Format
Instruction
Instr.1/5
SDI
SII
SDO
Write
EEPROM byte SDI
SII
SDO
Load “read
EEPROM”
Command
SDI
SII
SDO
SDI
Read
SII
EEPROM byte
SDO
Instr.2/6
0_bbbb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
0_aaaa_aaaa_00
0_0001_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
Instr.3/7
0_eeee_eeee_00
0_0010_1100_00
x_xxxx_xxxx_xx
Instr.4
0_0000_0000_00
0_0110_1101_00
x_xxxx_xxxx_xx
Operation Remarks
Repeat Instr. 1 - 6 for each
new address. Wait after Instr. 6
until SDO goes high. (3)
Instr. 5-6
0_0000_0011_00
0_0100_1100_00
x_xxxx_xxxx_xx
Enter EEPROM read mode.
0_bbbb_bbbb_00
0_0000_1100_00
x_xxxx_xxxx_xx
0_aaaa_aaaa_00
0_0001_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1000_00
x_xxxx_xxxx_xx
0_0000_0000_00 Repeat Instr. 1, 3 - 4 for each
0_0110_1100_00 new address. Repeat Instr. 2
q_qqqq_qqq0_00 for a new 256-byte page.
Write fuse
Low bits
SDI
SII
SDO
0_0100_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_A987_6543_00
0_0010_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
Wait after Instr. 4 until SDO
goes high. Write A - 3 = “0” to
program the fuse bit.
Write fuse
High bits
SDI
SII
SDO
0_0100_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_IHGF_EDCB_00 0_0000_0000_00
0_0010_1100_00
0_0111_0100_00
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
x_xxxx_xxxx_xx
Wait after Instr. 4 until SDO
goes high. Write F - B = “0” to
program the fuse bit.
Write fuse
Extended bits
SDI
SII
SDO
0_0100_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_000J_00
0_0010_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0110_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1110_00
x_xxxx_xxxx_xx
Wait after Instr. 4 until SDO
goes high. Write J = “0” to
program the fuse bit.
Write lock bits
SDI
SII
SDO
0_0010_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_0021_00
0_0010_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_0100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_xxxx_xx
Wait after Instr. 4 until SDO
goes high. Write 2 - 1 = “0” to
program the lock bit.
Read fuse
Low bits
SDI
SII
SDO
0_0000_0100_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1000_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
A_9876_543x_xx
Reading A - 3 = “0” means the
fuse bit is programmed.
Read fuse
High bits
SDI
SII
SDO
0_0000_0100_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1010_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
I_HGFE_DCBx_xx
Reading F - B = “0” means the
fuse bit is programmed.
Read fuse
Extended bits
SDI
SII
SDO
0_0000_0100_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1010_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1110_00
x_xxxx_xxJx_xx
Reading J = “0” means the
fuse bit is programmed.
Read lock bits
SDI
SII
SDO
0_0000_0100_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1000_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1100_00
x_xxxx_x21x_xx
Reading 2, 1 = “0” means the
lock bit is programmed.
a = address high bits, b = address low bits, d = data in high bits, e = data in low bits, p = data out high bits,
q = data out low bits, x = don’t care, 1 = Lock Bit1, 2 = Lock Bit2, 3 = CKSEL0 Fuse, 4 = CKSEL1 Fuse, 5 = CKSEL2 Fuse,
6 = CKSEL3 Fuse, 7 = SUT0 Fuse, 8 = SUT1 Fuse, 9 = CKDIV8 Fuse, A = CKOUT Fuse, B = BODLEVEL0 Fuse,
C = BODLEVEL1 Fuse, D= BODLEVEL2 Fuse, E = EESAVE Fuse, F = WDTON Fuse, G = SPIEN Fuse, H = DWEN Fuse,
I = RSTDISBL Fuse
Notes:
1.
For page sizes less than 256 words, parts of the address (bbbb_bbbb) will be parts of the page address.
2.
For page sizes less than 256 bytes, parts of the address (bbbb_bbbb) will be parts of the page address.
3.
The EEPROM is written page-wise. But only the bytes that are loaded into the page are actually written to the
EEPROM. Page-wise EEPROM access is more efficient when multiple bytes are to be written to the same
page. Note that auto-erase of EEPROM is not available in high-voltage serial programming, only in SPI
programming.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
153
Table 21-15. High-voltage Serial Programming Instruction Set for ATtiny24/44/84 (Continued)
Instruction Format
Instruction
Instr.1/5
Instr.2/6
Instr.3/7
Instr.4
Operation Remarks
SDI
Read signature
SII
bytes
SDO
0_0000_1000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_00bb_00
0_0000_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0110_1000_00
x_xxxx_xxxx_xx
0_0000_0000_00
Repeats Instr 2 4 for each
0_0110_1100_00
signature byte address.
q_qqqq_qqqx_xx
SDI
Read
SII
calibration byte
SDO
0_0000_1000_00
0_0100_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0000_1100_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1000_00
x_xxxx_xxxx_xx
0_0000_0000_00
0_0111_1100_00
p_pppp_pppx_xx
Load “no
operation”
command
0_0000_0000_00
0_0100_1100_00
x_xxxx_xxxx_xx
SDI
SII
SDO
a = address high bits, b = address low bits, d = data in high bits, e = data in low bits, p = data out high bits,
q = data out low bits, x = don’t care, 1 = Lock Bit1, 2 = Lock Bit2, 3 = CKSEL0 Fuse, 4 = CKSEL1 Fuse, 5 = CKSEL2 Fuse,
6 = CKSEL3 Fuse, 7 = SUT0 Fuse, 8 = SUT1 Fuse, 9 = CKDIV8 Fuse, A = CKOUT Fuse, B = BODLEVEL0 Fuse,
C = BODLEVEL1 Fuse, D= BODLEVEL2 Fuse, E = EESAVE Fuse, F = WDTON Fuse, G = SPIEN Fuse, H = DWEN Fuse,
I = RSTDISBL Fuse
Notes:
154
1.
For page sizes less than 256 words, parts of the address (bbbb_bbbb) will be parts of the page address.
2.
For page sizes less than 256 bytes, parts of the address (bbbb_bbbb) will be parts of the page address.
3.
The EEPROM is written page-wise. But only the bytes that are loaded into the page are actually written to the
EEPROM. Page-wise EEPROM access is more efficient when multiple bytes are to be written to the same
page. Note that auto-erase of EEPROM is not available in high-voltage serial programming, only in SPI
programming.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
22.
Electrical Characteristics
22.1
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Parameters
Min.
Automotive operating temperature
Typ.
Max.
Unit
–40
+125
°C
Storage temperature
–65
+150
°C
Voltage on any pin except RESET
with respect to ground
–0.5
VCC + 0.5
V
Voltage on RESET with respect to GND
–0.5
+13.0
V
Voltage on VCC with respect to GND
–0.5
6.0
V
40.0
mA
200.0
mA
±5
mA(1)
DC current per I/O pin
DC current VCC and GND pins
(2)
Injection current at VCC = 0V to 5V
Notes: 1. Maximum current per port = ±30mA
2.
Functional corruption may occur
Table 22-1. DC Characteristics TA = –40°C to 125°C, VCC = 2.7V to 5.5V (unless otherwise noted)(1)
Parameter
Condition
Symbol
Min.
Input low voltage
VCC = 2.4V to 5.5V
VIL
Input high-voltage
Except RESET pin
VCC = 2.4V to 5.5V
Input high-voltage
RESET pin
Max.
Units
–0.5
0.3VCC
V
VIH
0.6VCC(3)
VCC + 0.5(2)
V
VIH2
0.9VCC(3)
VCC + 0.5(2)
V
0.8
0.5
V
V
Output low voltage(4)
(port B,PORTA)
IOL = 10mA, VCC = 5V
IOL = 5mA, VCC = 3V
VOL
Output high-voltage(5)
(Port B2:0,PORTA)
IOH = –10mA, VCC = 5V
IOH = –5mA, VCC = 3V
VOH
Input leakage
Current I/O pin
VCC = 5.5V, pin low
(absolute value)
Typ.
4.3
2.5
V
V
IILPORTA
50
nA
Input leakage
VCC = 5.5V, pin high
IIHPORTA
50
nA
Current I/O pin
(absolute value)
®
Notes: 1. All DC Characteristics contained in this data sheet are based on actual silicon characterization of Atmel
ATtiny24/44/84 AVR® microcontrollers manufactured in corner run process technology. These values are preliminary
values representing design targets, and will be updated after characterization of actual Automotive silicon.
2.
“Max” means the highest value where the pin is guaranteed to be read as low.
3.
“Min” means the lowest value where the pin is guaranteed to be read as high.
4.
Although each I/O port can sink more than the test conditions (10mA at VCC = 5V, 5mA at VCC = 3V) under steady state
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current
greater than the listed test condition.
5.
Although each I/O port can source more than the test conditions (10mA at VCC = 5V, 5mA at VCC = 3V) under steady
state conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition. Pull up driving strength of the PB3 RESET pad is weak.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
155
Table 22-1. DC Characteristics TA = –40°C to 125°C, VCC = 2.7V to 5.5V (unless otherwise noted)(1) (Continued)
Parameter
Condition
Symbol
Input leakage
Current I/O pin
Vcc = 5.5V, pin low
(absolute value)
Input leakage
Current I/O pin
Vcc = 5.5V, pin high
(absolute value)
Min.
Typ.
Max.
Units
IIHPORTB
< 0.05
1
µA
IILPORTB
< 0.05
1
µA
Reset pull-up resistor
RRST
30
60
k
I/O pin pull-up resistor
Rpu
20
50
k
Power supply current
Active 1MHz, VCC = 3V
0.4
1.5
mA
Active 4MHz, VCC = 3V
1.8
3.0
mA
Active 8MHz, VCC = 5V
5.0
10.0
mA
0.075
0.2
mA
0.3
0.5
mA
1.2
2.5
mA
WDT enabled, VCC = 3V
5.0
30
µA
WDT enabled, VCC = 5V
9.0
50
µA
WDT disabled, VCC = 3V
2.5
24
µA
WDT disabled, VCC = 5V
4.3
36
µA
Idle 1MHz, VCC = 3V
Idle 4MHz, VCC = 3V
Idle 8MHz, VCC = 5V
Power-down mode
ICC
Analog comparator input
VCC = 5V
IACLK
–50
50
nA
Leakage current
Vin = VCC/2
Notes: 1. All DC Characteristics contained in this data sheet are based on actual silicon characterization of Atmel®
ATtiny24/44/84 AVR® microcontrollers manufactured in corner run process technology. These values are preliminary
values representing design targets, and will be updated after characterization of actual Automotive silicon.
156
2.
“Max” means the highest value where the pin is guaranteed to be read as low.
3.
“Min” means the lowest value where the pin is guaranteed to be read as high.
4.
Although each I/O port can sink more than the test conditions (10mA at VCC = 5V, 5mA at VCC = 3V) under steady state
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current
greater than the listed test condition.
5.
Although each I/O port can source more than the test conditions (10mA at VCC = 5V, 5mA at VCC = 3V) under steady
state conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition. Pull up driving strength of the PB3 RESET pad is weak.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
22.2
Speed Grades
Figure 22-1. Maximum Frequency versus VCC
16MHz
8MHz
Safe Operating
Area
2.7V
22.3
4.5V
5.5V
Clock Characterizations
22.3.1 Calibrated Internal RC Oscillator Accuracy
Table 22-2. Calibration Accuracy of Internal RC Oscillator
Frequency
VCC
Temperature
Accuracy
8.0MHz
3V
25°C
±2%
7.3 to 8.1MHz
2.7V to 5.5V
–40°C to 125°C
±20%
–40°C to 125°
Standard deviation 0.4ns(1)
Factory calibration
User calibration
Oscillator jitter
8.0MHz
2.7V to 5.5V
Note:
1. The overall jitter increase proportionally to the divider ratio
Example:
With oscillator divided by 32, jitter standard deviation will be 32 0.4ns = 12.8ns.
22.3.2 External Clock Drive Waveforms
Figure 22-2. External Clock Drive Waveforms
tCHCX
tCLCH
tCHCX
tCHCL
VIH1
VIL1
tCLCX
tCLCL
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
157
22.3.3 External Clock Drive
Table 22-3. External Clock Drive
VCC = 2.7 to 5.5V
VCC = 4.5 to 5.5V
Symbol
Min.
Max.
Min.
Max.
Units
1/tCLCL
0
10
0
20
MHz
Clock period
tCLCL
100
50
ns
High time
tCHCX
40
20
ns
Low time
tCLCX
40
20
ns
Rise time
tCLCH
1.6
0.5
µs
Fall time
tCHCL
1.6
0.5
µs
Change in period from one clock cycle to the next
tCLCL
2
2
%
Parameter
Clock frequency
22.4
System and Reset Characterizations
Table 22-4. Reset, Brown-out and Internal Voltage Reference Characteristics(1)
Parameter
Condition
Brown-out detector hysteresis
RAM retention voltage
Symbol
Min
VHYST
(1)
VRAM2.
Min pulse width on brown-out reset
Typ
Max
Units
100
250
mV
50
tBOD
mV
2
Bandgap reference voltage
VC C = 2.7V, TA = 25°C
VBG
1.1
1.2
V
Bandgap reference start-up time
VC C = 2.7V, TA = 25°C
tBG
40
70
µs
Bandgap reference current consumption
Notes: 1. Values are guidelines only.
VC C = 2.7V, TA = 25°C
IBG
10
2.
1.0
ns
µA
This is the limit to which VDD can be lowered without losing RAM data
Table 22-5. BODLEVEL Fuse Coding(1)
BODLEVEL [2..0] Fuses
Min VBOT
111
158
1.
Max VBOT
Units
BOD disabled
110
Note:
Typ VBOT
1.8
101
2.5
2.7
2.9
100
4.0
4.3
4.6
011
2.3
010
2.2
001
1.9
V
000
2.0
VBOT may be below nominal minimum operating voltage for some devices. For devices where this is the case,
the device is tested down to VCC = VBOT during the production test. This guarantees that a brown-out reset will
occur before VCC drops to a voltage where correct operation of the microcontroller is no longer guaranteed.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
22.5
ADC Characteristics – Preliminary Data
Table 22-6. ADC Characteristics, Single Ended Channels. –40°C to +125°C
Parameter
Condition
Resolution
Single-ended conversion
10
Single-ended conversion
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
2.0
4.0
LSB
2.0
4.0
LSB
Absolute accuracy (Including
INL, DNL, quantization error,
gain and offset error)
Single-ended conversion
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
Noise reduction mode
Symbol
Min
Typ
Max
Units
Bits
TUE
Single-ended conversion
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
INL
0.5
1.5
LSB
Single-ended conversion
Differential non-linearity (DNL) VREF = 4V, VCC = 4V,
ADC clock = 200kHz
DNL
0.3
0.7
LSB
Integral non-linearity (INL)
Gain error
Single-ended conversion
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
–5.0
–3.0
+5.0
LSB
Offset error
Single-ended conversion
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
–3.5
+1.5
+3.5
LSB
Conversion time
Free running conversion
65
260
µs
Clock frequency
50
200
kHz
VREF
2.56
AVCC
V
Input voltage
VIN
GND
VREF
V
Internal voltage reference
VINT
1.0
1.2
V
Analog input resistance
RAIN
External voltage reference
1.1
100
M
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
159
Table 22-7. ADC Characteristics, Differential Channels, TA = –40°C to +125°C
Parameter
Resolution
Absolute accuracy
Condition
Symbol
Min
Differential non-linearity (DNL)
Offset error
Units
Bits
Gain = 20x
8
Bits
Gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
2.5
5.0
LSB
3.0
6.0
LSB
0.5
2.5
LSB
0.5
3.0
LSB
Unipolar – Gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
1.5
5.0
LSB
Gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
0.4
1.0
LSB
0.4
1.0
LSB
0.7
2.0
LSB
Gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
TUE
Bipolar – gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
Bipolar – gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
INL
DNL
Unipolar – gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
Gain error
Max
8
Gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
Integral non-linearity (INL)
Typ
Gain = 1x
Bipolar – gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
–5.0
+2.3
+5.0
LSB
Unipolar – gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
–5.0
–2.8
+5.0
LSB
Bipolar – gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
–7.0
+2.2
+7.0
LSB
Unipolar – gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
–7.0
–1.8
+7.0
LSB
Gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
–5.0
+2.0
+5.0
LSB
Bipolar – gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
–5.0
+2.0
+5.0
LSB
Unipolar – gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 to 200kHz
–6.5
+2.0
+6.5
LSB
Clock frequency
50
200
kHz
Conversion time
65
260
µs
160
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Table 22-7. ADC Characteristics, Differential Channels, TA = –40°C to +125°C (Continued)
Parameter
Condition
Symbol
Reference voltage
Input voltage
Input differential voltage
22.6
Min
Typ
Max
Units
VREF
2.56
AVCC – 0.5
V
VIN
GND
AVCC
V
VDIFF
–VREF/gain
VREF/gain
V
Serial Programming Characteristics
Figure 22-3. Serial Programming Timing
MOSI
tOVSH
SCK
tSHOX
tSLSH
tSHSL
MISO
tSLIV
Figure 22-4. Serial Programming Waveforms
SERIAL DATA INPUT
(MOSI)
MSB
LSB
SERIAL DATA OUTPUT
(MISO)
MSB
LSB
SERIAL CLOCK INPUT
(SCK)
SAMPLE
Table 22-8. Serial Programming Characteristics, TA = –40°C to +125°C, VCC = 2.7 to 5.5V (Unless Otherwise Noted)
Parameter
Symbol
®
Oscillator frequency (Atmel ATtiny24/44/84V)
Min
Typ
Max
Units
4
MHz
1/tCLCL
0
tCLCL
250
1/tCLCL
0
Oscillator period (ATtiny24/44/84, VCC = 4.5V to 5.5V)
tCLCL
50
ns
SCK pulse width high
tSHSL
2 tCLCL*
ns
SCK pulse width low
tSLSH
2 tCLCL*
ns
MOSI setup to SCK high
tOVSH
tCLCL
ns
MOSI hold after SCK high
tSHOX
2 tCLCL
ns
SCK low to MISO valid
Note:
2 tCLCL for fck < 12MHz, 3 tCLCL for fck ≥ 12MHz
tSLIV
TBD
Oscillator period (Atmel ATtiny24/44/84V)
Oscillator frequency (ATtiny24/44/84, VCC = 4.5V to 5.5V)
ns
20
TBD
TBD
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
MHz
ns
161
22.7
High-voltage Serial Programming Characteristics
Figure 22-5. High-voltage Serial Programming Timing
VCC
RESET
1 CK Cycle
WDT
Time-out
RESET
Time-out
tTOUT
Internal
Reset
Table 22-9. High-voltage Serial Programming Characteristics
TA = 25°C ±10%, VCC = 5.0V ±10% (Unless otherwise noted)
Parameter
162
Symbol
Min
SCI (PB0) pulse width high
tSHSL
110
ns
SCI (PB0) pulse width low
tSLSH
110
ns
SDI (PA6), SII (PB1) valid to SCI (PB0) high
tIVSH
50
ns
SDI (PA6), SII (PB1) hold after SCI (PB0) high
tSHIX
50
SCI (PB0) high to SDO (PA4) valid
tSHOV
16
ns
Wait after Instr. 3 for write fuse bits
tWLWH_PFB
2.5
ms
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
Typ
Max
Units
ns
23.
Typical Characteristics – Preliminary Data
The data contained in this section is largely based on simulations and characterization of similar devices in the same
process and design methods. Thus, the data should be treated as indications of how the part will behave.
The following charts show typical behavior. These figures are not tested during manufacturing. All current consumption
measurements are performed with all I/O pins configured as inputs and with internal pull-ups enabled. A sine wave generator
with rail-to-rail output is used as clock source.
The power consumption in power-down mode is independent of clock selection.
The current consumption is a function of several factors such as: operating voltage, operating frequency, loading of I/O pins,
switching rate of I/O pins, code executed and ambient temperature. The dominating factors are operating voltage and
frequency.
The current drawn from capacitive loaded pins may be estimated (for one pin) as CL  VCCf where CL = load capacitance,
VCC = operating voltage and f = average switching frequency of I/O pin.
The parts are characterized at frequencies higher than test limits. Parts are not guaranteed to function properly at
frequencies higher than the ordering code indicates.
The difference between current consumption in power-down mode with watchdog timer enabled and power-down mode with
watchdog timer disabled represents the differential current drawn by the watchdog timer.
Active Supply Current
Figure 23-1. Active Supply Current versus Low Frequency (0.1 to 1.0MHz) - Temperature = 25°C
1.2
5.5V
1
5.0V
4.5V
0.8
ICC (mA)
23.1
3.3V
3.0V
2.7V
0.6
0.4
0.2
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Frequency (MHz)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
163
Figure 23-2. Active Supply Current versus Low Frequency (0.1 to 1.0MHz) - Temperature = 125°C
1.2
5.5V
1
5.0V
ICC (mA)
0.8
4.5V
0.6
3.3V
3.0V
2.7V
0.4
0.2
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Frequency (MHz)
Figure 23-3. Active Supply Current versus Frequency (1 to 20MHz) - Temperature = 25°C
25
ICC (mA)
20
15
5.5V
5.0V
4.5V
10
3.3V
3.0V
2.7V
5
0
0
2
4
6
8
10
12
14
16
18
20
Frequency (MHz)
Figure 23-4. Active Supply Current versus Frequency (1 to 20MHz) - Temperature = 125°C
25
ICC (mA)
20
15
10
5.5V
5.0V
4.5V
5
3.3V
3.0V
2.7V
0
0
2
4
6
8
10
12
Frequency (MHz)
164
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
14
16
18
20
Figure 23-5. Active Supply Current versus VCC (Internal RC Oscillator, 8MHz)
7
125°C
85°C
25°C
-45°C
6
ICC (mA)
5
4
3
2
1
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-6. Active Supply Current versus VCC (Internal RC Oscillator, 1MHz)
1.4
125°C
85°C
25°C
-40°C
1.2
ICC (mA)
1
0.8
0.6
0.4
0.2
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-7. Active Supply Current versus VCC (Internal RC Oscillator, 128kHz)
0.2
ICC (mA)
0.16
-40°C
25°C
85°C
125°C
0.12
0.08
0.04
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
165
23.2
Idle Supply Current
Figure 23-8. Idle Supply Current versus Low Frequency (0.1 to 1.0MHz)
0.012
5.5V
0.01
ICC (mA)
5.0V
0.008
4.5V
0.006
3.3V
3.0V
2.7V
0.004
0.002
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Frequency (MHz)
Figure 23-9. Idle Supply Current versus Frequency (1 to 20MHz)
4
ICC (mA)
3.5
5.5V
3
5.0V
2.5
4.5V
2
3.3V
3.0V
2.7V
1.5
1
0.5
0
0
2
4
6
8
10
12
Frequency (MHz)
166
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
14
16
18
20
Figure 23-10. Idle Supply Current versus VCC (Internal RC Oscillator, 8MHz)
2
1.8
1.6
125°C
85°C
25°C
-45°C
ICC (mA)
1.4
1.2
1
0.8
0.6
0.4
0.2
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-11. Idle Supply Current versus VCC (Internal RC Oscillator, 1MHz)
0.35
125°C
85°C
25°C
-40°C
0.3
ICC (mA)
0.25
0.2
0.15
0.1
0.05
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-12. Idle Supply Current versus VCC (Internal RC Oscillator, 128kHz)
0.035
0.03
125°C
85°C
25°C
-40°C
ICC (mA)
0.025
0.02
0.015
0.01
0.005
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
167
23.3
Supply Current of IO modules
The tables and formulas below can be used to calculate the additional current consumption for the different I/O modules in
Active and Idle mode. The enabling or disabling of the I/O modules are controlled by the power reduction register. See
Section 8.7 “Power Reduction Register” on page 32 for details.
Table 23-1. Additional Current Consumption for the different I/O Modules (Absolute Values)
PRR bit
23.4
Typical numbers
VCC = 2V, F = 1MHz
VCC = 3V, F = 4MHz
VCC = 5V, F = 8MHz
PRTIM1
6.6µA
26µA
106µA
PRTIM0
8.7µA
35µA
140µA
PRUSI
5.5µA
22µA
87µA
PRADC
22µA
87µA
340µA
Power-down Supply Current
Figure 23-13. Power-down Supply Current versus VCC (Watchdog Timer Disabled)
5
4.5
4
ICC (µA)
3.5
125°C
3
2.5
2
1.5
85°C
1
0.5
0
2.5
25°C
-45°C
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-14. Power-down Supply Current versus VCC (Watchdog Timer Enabled)
10
9
8
ICC (µA)
7
6
5
4
125°C
-45°C
85°C
25°C
3
2
1
0
2.5
3
3.5
4
VCC (V)
168
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
4.5
5
5.5
Pin Pull-up
Figure 23-15. I/O Pin Pull-up Resistor Current versus input Voltage (VCC = 2.7V)
90
80
70
IOP (µA)
60
50
40
30
20
-45°C
25°C
85°C
125°C
10
0
0
0.5
1
1.5
2
2.5
3
VOP (V)
Figure 23-16. I/O pin Pull-up Resistor Current versus Input Voltage (VCC = 5V)
160
140
120
100
IOP (µA)
23.5
80
60
40
-45°C
25°C
85°C
125°C
20
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
VOP (V)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
169
Figure 23-17. Reset Pull-up Resistor Current versus Reset Pin Voltage (VCC = 2.7V)
60
-40°C
50
125°C
IRESET (µA)
40
30
20
10
0
0
0.5
1
1.5
2
2.5
3
VRESET (V)
Figure 23-18. Reset Pull-up Resistor Current versus Reset Pin Voltage (VCC = 5V)
120
-40°C
100
125°C
IRESET (µA)
80
60
40
20
0
0
0.5
1
1.5
2
2.5
VRESET (V)
170
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
3
3.5
4
4.5
5
Pin Driver Strength
Figure 23-19. I/O Pin Output Voltage versus Sink Current (VCC = 3V)
0.06
125°C
0.05
VOL (V)
0.04
85°C
25°C
-40°C
0.03
0.02
0.01
0
0
2
4
6
8
10
12
14
16
18
20
IOL (mA)
Figure 23-20. I/O pin Output Voltage versus Sink Current (VCC = 5V)
0.7
125°C
0.6
85°C
0.5
VOL (V)
25°C
0.4
-45°C
0.3
0.2
0.1
0
0
2
4
6
8
10
12
14
16
18
20
IOL (mA)
Figure 23-21. I/O Pin Output Voltage versus Source Current (VCC = 3V)
3.5
3
VOH (V)
23.6
2.5
-45°C
25°C
85°C
125°C
2
1.5
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
171
Figure 23-22. I/O Pin output Voltage versus Source Current (VCC = 5V)
5.1
5
4.9
VOH (V)
4.8
4.7
4.6
-45°C
4.5
25°C
4.4
85°C
125°C
4.3
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
23.7
Pin Threshold and Hysteresis
Figure 23-23. I/O Pin Input Threshold Voltage versus VCC (VIH, IO Pin Read as ‘1’)
3.5
125°C
85°C
25°C
-40°C
3
Threshold (V)
2.5
2
1.5
1
0.5
0
2.5
3
3.5
4
VCC (V)
172
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
4.5
5
5.5
Figure 23-24. I/O Pin Input threshold Voltage versus VCC (VIL, IO Pin Read as ‘0’)
125°C
85°C
25°C
-40°C
2.5
Threshold (V)
2
1.5
1
0.5
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-25. I/O Pin Input Hysteresis versus VCC
0.5
125°C
85°C
-20°C
-40°C
0.45
Input Hysteresis (mV)
0.4
0.35
0.3
0.25
0.2
0.15
0.1
0.05
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-26. Reset Input Threshold Voltage versus VCC (VIH, IO Pin Threshold as ‘1’)
3
125°C
85°C
25°C
-40°C
Threshold (mV)
2.5
2
1.5
1
0.5
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
173
Figure 23-27. Reset Input Threshold Voltage versus VCC (VIL, IO pin Read as ‘0’)
3
Threshold (mV)
2.5
125°C
85°C
25°C
-45°C
2
1.5
1
0.5
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-28. Reset Pin Input Hysteresis versus VCC
1
0.9
Input Hysteresis (mV)
0.8
0.7
0.6
0.5
-40°C
0.4
0.3
25°C
0.2
85°C
0.1
125°C
0
2.5
3
3.5
4
VCC (V)
174
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
4.5
5
5.5
BOD Threshold and Analog Comparator Offset
Figure 23-29. BOD Threshold versus Temperature (BODLEVEL is 4.3V)
4.4
1
Threshold (V)
4.35
4.3
0
4.25
4.2
4.15
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
100
110
120
Temperature (°C)
Figure 23-30. BOD Threshold versus Temperature (BODLEVEL is 2.7V)
2.78
1
2.76
2.74
Threshold (V)
23.8
2.72
2.7
0
2.68
2.66
2.64
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
100
110
120
Temperature (°C)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
175
Figure 23-31. BOD Threshold versus Temperature (BODLEVEL is 1.8V)
1.85
1
1.84
Threshold (V)
1.83
1.82
1.81
0
1.8
1.79
1.78
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
100
110
120
Temperature (°C)
23.9
Internal Oscillator Speed
Figure 23-32. Watchdog Oscillator Frequency versus VCC
124
122
-40°C
120
FRC (kHz)
118
25°C
116
114
112
85°C
110
108
125°C
106
104
2.5
3
3.5
4
VCC (V)
176
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
4.5
5
5.5
Figure 23-33. Calibrated 8MHz RC Oscillator Frequency versus VCC
9
8.5
-40°C
25°C
85°C
125°C
FRC (MHz)
8
7.5
7
6.5
6
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-34. Calibrated 8MHz RC Oscillator Frequency versus Temperature
8.4
8.3
5.0V
3.0V
FRC (MHz)
8.2
8.1
8
7.9
7.8
7.7
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
100
110
120
Temperature (°C)
Figure 23-35. Calibrated 8MHz RC Oscillator Frequency versus OSCCAL Value
16
125°C
85°C
25°C
-40°C
14
FRC (MHz)
12
10
8
6
4
2
0
0
16
32
48
64
80
96
112
128
144
160
176
192
208
224
240
OSCCAL (X1)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
177
23.10 Current Consumption of Peripheral Units
Figure 23-36. ADC Current versus VCC
700
125°C
85°C
25°C
-40°C
600
ICC (µA)
500
400
300
200
100
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-37. AREF External Reference Current versus VCC
14
25°C
AREF Pin Current (µA)
12
10
8
6
4
2
0
1.5
2
2.5
3
3.5
AREF (V)
178
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
4
4.5
5
5.5
Figure 23-38. Analog Comparator Current versus VCC
100
-40°C
25°C
85°C
125°C
90
80
ICC (µA)
70
60
50
40
30
20
10
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 23-39. Programming Current versus VCC
12000
25°C
10000
ICC (µA)
8000
6000
4000
2000
0
2.5
3.5
4.5
5.5
VCC (V)
Figure 23-40. Watchdog Timer Current versus VCC
30
-40°C
25°C
85°C
125°C
25
ICC (µA)
20
15
10
5
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
179
23.11 Current Consumption in Reset and Reset Pulse Width
Figure 23-41. Reset Supply Current versus VCC (0.1 to 1.0MHz, excluding Current Through the Reset Pull-up)
0.2
5.5V
0.18
5.0V
0.16
4.5V
ICC (mA)
0.14
0.12
3.3V
3.0V
0.1
2.7V
0.08
0.06
0.04
0.02
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Frequency (MHz)
Figure 23-42. Reset Supply Current versus VCC (1 to 20MHz, Excluding Current Through the Reset Pull-up)
3
2.5
5.5V
5.0V
ICC (mA)
2
4.5V
1.5
3.6V
3.3V
3.0V
2.7V
1
0.5
0
0
2
4
6
8
10
12
Frequency (MHz)
180
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
14
16
18
20
Figure 23-43. Minimum Reset Pulse Width versus VCC
1200
Pulse Width (ns)
1000
800
600
125°C
85°C
25°C
-40°C
400
200
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
181
24.
Register Summary
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
0x3F (0x5F)
SREG
I
T
H
S
V
N
Z
C
10
0x3E (0x5E)
SPH
–
–
–
–
–
–
SP9
SP8
13
0x3D (0x5D)
SPL
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0
13
0x3C (0x5C)
OCR0B
0x3B (0x5B)
GIMSK
–
INT0
PCIE1
PCIE0
–
–
–
47
0x3A (0x5A
GIFR
–
INTF0
PCIF1
PCIF0
–
–
–
–
48
0x39 (0x59)
TIMSK0
–
–
–
–
–
OCIE0B
OCIE0A
TOIE0
77
0x38 (0x58)
TIFR0
0x37 (0x57)
SPMCSR
0x36 (0x56)
OCR0A
0x35 (0x55)
MCUCR
Timer/Counter0 – Output compare register B
76
–
–
–
–
–
OCF0B
OCF0A
TOV0
77
–
–
–
CTPB
RFLB
PGWRT
PGERS
SPMEN
140
BODS
PUD
SE
SM1
Timer/Counter0 – Output compare register A
76
SM0
BODSE
ISC01
ISC00
47
0x34 (0x54)
MCUSR
–
–
–
–
WDRF
BORF
EXTRF
PORF
41
0x33 (0x53)
TCCR0B
FOC0A
FOC0B
–
–
WGM02
CS02
CS01
CS00
75
CAL7
CAL6
CAL5
CAL4
CAL2
CAL1
CAL0
0x32 (0x52)
TCNT0
0x31 (0x51)
OSCCAL
Timer/Counter0
CAL3
76
29
0x30 (0x50)
TCCR0A
COM01 COM0A0 COM0B1 COM0B0
–
WGM01 WGM00
73
0x2F (0x4F)
TCCR1A
COM11 COM1A0 COM1B1 COM1B0
–
WGM11 WGM10
97
0x2E (0x4E)
TCCR1B
ICNC1
0x2D (0x4D)
TCNT1H
ICES1
–
WGM13
WGM12
CS12
CS11
CS10
99
Timer/Counter1 – Counter register high byte
100
0x2C (0x4C)
TCNT1L
Timer/Counter1 – Counter register low byte
100
0x2B (0x4B)
OCR1AH
Timer/Counter1 – Compare register A high byte
100
0x2A (0x4A)
OCR1AL
Timer/Counter1 – Compare register A low byte
100
0x29 (0x49)
OCR1BH
Timer/Counter1 – Compare register B high byte
101
0x28 (0x48)
OCR1BL
Timer/Counter1 – Compare register B low byte
101
0x27 (0x47)
DWDR
DWDR[7:0]
136
0x26 (0x46)
CLKPR
0x25 (0x45)
ICR1H
CLKPCE
–
–
–
CLKPS3 CLKPS2 CLKPS1 CLKPS0
Timer/Counter1 - Input capture register high byte
0x24 (0x44)
ICR1L
0x23 (0x43)
GTCCR
TSM
–
Timer/Counter1 - Input capture register low byte
0x22 (0x42)
TCCR1C
FOC1A
FOC1B
–
–
–
–
0x21 (0x41)
WDTCSR
WDIF
WDIE
WDP3
WDCE
WDE
WDP2
–
–
–
–
29
101
101
–
PSR10
104
–
–
100
WDP1
WDP0
41
0x20 (0x40)
PCMSK1
–
–
–
–
PCINT8
48
0x1F (0x3F)
EEARH
–
–
–
–
–
–
–
EEAR8
21
0x1E (0x3E)
EEARL
EEAR7
EEAR6
EEAR5
EEAR4
EEAR3
EEAR2
EEAR1
EEAR0
21
0x1D (0x3D)
EEDR
0x1C (0x3C)
EECR
0x1B (0x3B)
PORTA
0x1A (0x3A)
DDRA
PCINT11 PCINT10 PCINT9
EEPROM data register
–
–
EEPM1
EEPM0
EERIE
21
EEMPE
EEPE
EERE
PORTA7 PORTA6 PORTA5 PORTA4 PORTA3 PORTA2 PORTA1 PORTA0
DDA7
DDA6
DDA5
DDA4
DDA3
DDA2
DDA1
DDA0
22
61
61
0x19 (0x39)
PINA
PINA7
PINA6
PINA5
PINA4
PINA3
PINA2
PINA1
PINA0
62
Notes: 1. For compatibility with future devices, reserved bits should be written to logical zero if accessed. Reserved I/O memory
addresses should never be written.
182
2.
I/O registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In
these registers, the value of single bits can be checked by using the SBIS and SBIC instructions.
3.
Some of the status flags are cleared by writing a logical one to them. Note that, unlike most other AVR®, the CBI and
SBI instructions will only operation the specified bit, and can therefore be used on registers containing such status
flags. The CBI and SBI instructions work with registers 0x00 to 0x1F only.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
24.
Register Summary (Continued)
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0x18 (0x38)
PORTB
–
–
–
–
0x17 (0x37)
DDRB
–
–
–
–
DDB3
DDB2
DDB1
DDB0
62
0x16 (0x36)
PINB
–
–
–
–
PINB3
PINB2
PINB1
PINB0
62
0x15 (0x35)
GPIOR2
General purpose I/O register 2
23
0x14 (0x34)
GPIOR1
General purpose I/O register 1
23
0x13 (0x33)
GPIOR0
General purpose I/O register 0
23
0x12 (0x32)
PCMSK0
PCINT7
PCINT6
PCINT5
PCINT4
0x11 (0x31)) Reserved
0x10 (0x30)
PORTB3 PORTB2 PORTB1 PORTB0
Page
PCINT3
PCINT2
PCINT1
PCINT0
62
48
–
USIBR
USI buffer register
111
0x0F (0x2F) USIDR
USI data register
111
0x0E (0x2E) USISR
USISIF
USIOIF
USICN3
USICN2
USICN1 USICN0
112
0x0D (0x2D) USICR
USISIE
USIOIE USIWM1 USIWM0 USICS1
USIPF
USIDC
USICS0
USICLK
USITC
112
0x0C (0x2C) TIMSK1
–
–
ICIE1
–
–
OCIE1B
OCIE1A
TOIE1
101
0x0B (0x2B) TIFR1
–
–
ICF1
–
–
OCF1B
OCF1A
TOV1
102
0x0A (0x2A) Reserved
–
0x09 (0x29)
–
Reserved
0x08 (0x28)
ACSR
ACD
ACBG
ACO
ACI
ACIE
ACIC
ACIS1
ACIS0
116
0x07 (0x27)
ADMUX
REFS1
REFS0
MUX5
MUX4
MUX3
MUX2
MUX1
MUX0
129
0x06 (0x26)
ADCSRA
ADEN
ADSC
ADATE
ADIF
ADIE
ADPS2
ADPS1
ADPS0
132
0x05 (0x25)
ADCH
0x04 (0x24)
ADCL
0x03 (0x23)
ADCSRB
0x02 (0x22)
Reserved
0x01 (0x21)
DIDR0
ADC data register high byte
133
ADC data register low byte
BIN
ACME
–
ADLAR
ADC7D
ADC6D
ADC5D
ADC4D
133
–
ADTS2
ADTS1
ADTS0
133
ADC3D
ADC2D
ADC1D
ADC0D
117,134
–
0x00 (0x20) PRR
–
–
–
–
PRTIM1 PRTIM0 PRUSI PRADC
32
Notes: 1. For compatibility with future devices, reserved bits should be written to logical zero if accessed. Reserved I/O memory
addresses should never be written.
2.
I/O registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In
these registers, the value of single bits can be checked by using the SBIS and SBIC instructions.
3.
Some of the status flags are cleared by writing a logical one to them. Note that, unlike most other AVR®, the CBI and
SBI instructions will only operation the specified bit, and can therefore be used on registers containing such status
flags. The CBI and SBI instructions work with registers 0x00 to 0x1F only.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
183
25.
Instruction Set Summary
Mnemonics
Operands
Description
Operation
Flags
#Clocks
Arithmetic and Logic Instructions
ADD
Rd, Rr
Add two registers
Rd  Rd + Rr
Z,C,N,V,H
1
ADC
Rd, Rr
Add with carry two registers
Rd  Rd + Rr + C
Z,C,N,V,H
1
ADIW
Rdl, K
Add immediate to word
Rdh:Rdl  Rdh:Rdl + K
Z,C,N,V,S
2
SUB
Rd, Rr
Subtract two registers
Rd  Rd – Rr
Z,C,N,V,H
1
SUBI
Rd, K
Subtract constant from register
Rd  Rd – K
Z,C,N,V,H
1
SBC
Rd, Rr
Subtract with carry two registers
Rd  Rd – Rr – C
Z,C,N,V,H
1
SBCI
Rd, K
Subtract with carry constant from Reg.
Rd  Rd – K – C
Z,C,N,V,H
1
SBIW
Rdl, K
Subtract immediate from word
Rdh:Rdl  Rdh:Rdl – K
Z,C,N,V,S
2
AND
Rd, Rr
Logical AND registers
Rd Rd  Rr
Z,N,V
1
ANDI
Rd, K
Logical AND register and constant
Rd  Rd K
Z,N,V
1
OR
Rd, Rr
Logical OR registers
Rd  Rd v Rr
Z,N,V
1
ORI
Rd, K
Logical OR register and constant
Rd Rd v K
Z,N,V
1
EOR
Rd, Rr
Exclusive OR registers
Rd  Rd  Rr
Z,N,V
1
COM
Rd
One’s complement
Rd  0xFF  Rd
Z,C,N,V
1
NEG
Rd
Two’s complement
Rd  0x00  Rd
Z,C,N,V,H
1
SBR
Rd, K
Set bit(s) in register
Rd  Rd v K
Z,N,V
1
CBR
Rd, K
Clear bit(s) in register
Rd  Rd  (0xFF – K)
Z,N,V
1
INC
Rd
Increment
Rd  Rd + 1
Z,N,V
1
DEC
Rd
Decrement
Rd  Rd  1
Z,N,V
1
TST
Rd
Test for zero or minus
Rd  Rd  Rd
Z,N,V
1
CLR
Rd
Clear register
Rd  Rd  Rd
Z,N,V
1
SER
Rd
Set register
Rd  0xFF
None
1
Relative jump
PC PC + k + 1
None
2
Indirect jump to (Z)
PC  Z
None
2
Relative subroutine call
PC  PC + k + 1
None
3
ICALL
Indirect call to (Z)
PC  Z
None
3
RET
Subroutine return
PC  STACK
None
4
Branch Instructions
RJMP
k
IJMP
RCALL
k
Interrupt return
PC  STACK
I
CPSE
Rd, Rr
Compare, skip if equal
if (Rd = Rr) PC PC + 2 or 3
None
CP
Rd, Rr
Compare
Rd  Rr
Z, N,V,C,H
1
CPC
Rd, Rr
Compare with carry
Rd  Rr  C
Z, N,V,C,H
1
CPI
Rd, K
Compare register with immediate
Rd  K
Z, N,V,C,H
SBRC
Rr, b
Skip if bit in register cleared
if (Rr(b)=0) PC  PC + 2 or 3
None
1/2/3
SBRS
Rr, b
Skip if bit in register is set
if (Rr(b)=1) PC  PC + 2 or 3
None
1/2/3
SBIC
P, b
Skip if bit in I/O register cleared
if (P(b)=0) PC  PC + 2 or 3
None
1/2/3
SBIS
P, b
Skip if bit in I/O register is set
if (P(b)=1) PC  PC + 2 or 3
None
1/2/3
None
1/2
None
1/2
RETI
BRBS
s, k
Branch if status flag set
if (SREG (s) = 1) then PC 
PC + k + 1
BRBC
s, k
Branch if status flag cleared
if (SREG(s) = 0) then PC 
PC + k + 1
184
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
4
1/2/3
1
25.
Instruction Set Summary (Continued)
Mnemonics
Operands
Description
Operation
Flags
#Clocks
BREQ
k
Branch if equal
if (Z = 1) then PC  PC + k + 1
None
1/2
BRNE
k
Branch if not equal
if (Z = 0) then PC  PC + k + 1
None
1/2
BRCS
k
Branch if carry set
if (C = 1) then PC  PC + k + 1
None
1/2
BRCC
k
Branch if carry cleared
if (C = 0) then PC  PC + k + 1
None
1/2
BRSH
k
Branch if same or higher
if (C = 0) then PC  PC + k + 1
None
1/2
BRLO
k
Branch if lower
if (C = 1) then PC  PC + k + 1
None
1/2
BRMI
k
Branch if minus
if (N = 1) then PC  PC + k + 1
None
1/2
BRPL
k
Branch if plus
if (N = 0) then PC  PC + k + 1
None
1/2
BRGE
k
Branch if greater or equal, signed
if (N  V= 0) then PC  PC + k + 1 None
1/2
BRLT
k
Branch if less than zero, signed
if (N  V= 1) then PC  PC + k + 1 None
1/2
BRHS
k
Branch if half carry flag set
if (H = 1) then PC  PC + k + 1
None
1/2
BRHC
k
Branch if half carry flag cleared
if (H = 0) then PC  PC + k + 1
None
1/2
BRTS
k
Branch if T flag set
if (T = 1) then PC  PC + k + 1
None
1/2
BRTC
k
Branch if T flag cleared
if (T = 0) then PC  PC + k + 1
None
1/2
BRVS
k
Branch if overflow flag is set
if (V = 1) then PC  PC + k + 1
None
1/2
BRVC
k
Branch if overflow flag is cleared
if (V = 0) then PC  PC + k + 1
None
1/2
BRIE
k
Branch if interrupt enabled
if (I = 1) then PC  PC + k + 1
None
1/2
BRID
k
Branch if interrupt disabled
if (I = 0) then PC  PC + k + 1
None
1/2
Bit and Bit-Test Instructions
SBI
P,b
Set bit in I/O register
I/O (P, b)  1
None
2
CBI
P,b
Clear bit in I/O register
I/O (P, b)  0
None
2
LSL
Rd
Logical shift left
Rd(n+1)  Rd(n), Rd(0)  0
Z,C,N,V
1
LSR
Rd
Logical shift right
Rd(n)  Rd(n+1), Rd(7)  0
Z,C,N,V
1
ROL
Rd
Rotate left through carry
Rd(0) C,Rd(n+1)  Rd(n),
C Rd(7)
Z,C,N,V
1
ROR
Rd
Rotate right through carry
Rd(7) C, Rd(n)  Rd(n+1),
C Rd(0)
Z,C,N,V
1
ASR
Rd
Arithmetic shift right
Rd(n)  Rd(n+1), n=0..6
Z,C,N,V
1
None
1
SWAP
Rd
Swap nibbles
Rd(3..0) Rd(7..4),Rd(7..4) 
Rd(3..0)
BSET
s
Flag set
SREG(s)  1
SREG(s)
1
BCLR
s
Flag clear
SREG(s)  0
SREG(s)
1
BST
Rr, b
Bit store from register to T
T  Rr(b)
T
1
BLD
Rd, b
Bit load from T to register
Rd(b)  T
None
1
SEC
Set carry
C1
C
1
CLC
Clear carry
C0
C
1
SEN
Set negative flag
N1
N
1
CLN
Clear negative flag
N0
N
1
SEZ
Set zero flag
Z1
Z
1
CLZ
Clear zero flag
Z0
Z
1
SEI
Global interrupt enable
I1
I
1
CLI
Global interrupt disable
I 0
I
1
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
185
25.
Instruction Set Summary (Continued)
Mnemonics
Description
Operation
Flags
SES
Operands
Set signed test flag
S1
S
#Clocks
1
CLS
Clear signed test flag
S0
S
1
SEV
Set twos complement overflow.
V1
V
1
CLV
Clear twos complement overflow
V0
V
1
SET
Set T in SREG
T1
T
1
CLT
Clear T in SREG
T0
T
1
SEH
Set Half carry flag in SREG
H1
H
1
CLH
Clear half carry flag in SREG
H0
H
1
Data Transfer Instructions
MOV
Rd, Rr
Move between registers
Rd  Rr
None
1
MOVW
Rd, Rr
Copy register word
Rd+1:Rd  Rr+1:Rr
None
1
LDI
Rd, K
Load immediate
Rd  K
None
1
LD
Rd, X
Load indirect
Rd  (X)
None
2
LD
Rd, X+
Load indirect and post-inc.
Rd  (X), X  X + 1
None
2
LD
Rd, - X
Load indirect and pre-dec.
X  X – 1, Rd  (X)
None
2
LD
Rd, Y
Load indirect
Rd  (Y)
None
2
LD
Rd, Y+
Load indirect and post-inc.
Rd  (Y), Y  Y + 1
None
2
LD
Rd, - Y
Load indirect and pre-dec.
Y  Y – 1, Rd  (Y)
None
2
LDD
Rd,Y+q
Load indirect with displacement
Rd  (Y + q)
None
2
LD
Rd, Z
Load indirect
Rd  (Z)
None
2
LD
Rd, Z+
Load indirect and post-inc.
Rd  (Z), Z  Z+1
None
2
LD
Rd, -Z
Load indirect and pre-dec.
Z  Z 1, Rd  (Z)
None
2
LDD
Rd, Z+q
Load indirect with displacement
Rd  (Z + q)
None
2
LDS
Rd, k
Load direct from SRAM
Rd  (k)
None
2
ST
X, Rr
Store indirect
(X) Rr
None
2
ST
X+, Rr
Store indirect and post-inc.
(X) Rr, X  X + 1
None
2
ST
- X, Rr
Store indirect and pre-dec.
X  X 1, (X)  Rr
None
2
ST
Y, Rr
Store indirect
(Y)  Rr
None
2
ST
Y+, Rr
Store indirect and post-inc.
(Y)  Rr, Y  Y + 1
None
2
ST
- Y, Rr
Store indirect and pre-dec.
Y  Y 1, (Y)  Rr
None
2
STD
Y+q,Rr
Store indirect with displacement
(Y + q)  Rr
None
2
ST
Z, Rr
Store indirect
(Z)  Rr
None
2
ST
Z+, Rr
Store indirect and post-inc.
(Z)  Rr, Z  Z + 1
None
2
ST
-Z, Rr
Store indirect and pre-dec.
Z  Z 1, (Z)  Rr
None
2
STD
Z+q,Rr
Store indirect with displacement
(Z + q)  Rr
None
2
STS
k, Rr
Store direct to SRAM
(k)  Rr
None
2
Load program memory
R0  (Z)
None
3
LPM
LPM
Rd, Z
Load program memory
Rd  (Z)
None
3
LPM
Rd, Z+
Load program memory and post-inc
Rd  (Z), Z  Z+1
None
3
Store program memory
(z)  R1:R0
None
IN
Rd, P
In port
Rd  P
None
1
OUT
P, Rr
Out port
P  Rr
None
1
SPM
186
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
25.
Instruction Set Summary (Continued)
Mnemonics
Operands
Description
Operation
Flags
#Clocks
PUSH
Rr
Push register on stack
STACK  Rr
None
2
POP
Rd
Pop register from stack
Rd  STACK
None
2
MCU Control Instructions
NOP
No operation
None
1
None
1
SLEEP
Sleep
(see specific descr. for sleep
function)
WDR
Watchdog reset
(see specific descr. for WDR/timer)
None
1
BREAK
Break
For on-chip Debug Only
None
N/A
26.
Ordering Information
26.1
ATtiny24/44/84
Ordering Code
Speed (MHz)(3)
Power Supply (V)
Package(1)(2)
Operation Range
ATtiny24-15SSZ
16
2.7 to 5.5
TU
Automotive (–40° to +125°C)
ATtiny24-15MZ
16
2.7 to 5.5
PC
Automotive (–40° to +125°C)
ATtiny44-15SSZ
16
2.7 to 5.5
TU
Automotive (–40° to +125°C)
ATtiny44-15MZ
16
2.7 to 5.5
PC
Automotive (–40° to +125°C)
2.7 to 5.5
PC
Automotive (–40° to +125°C)
ATtiny84-15MZ
16
Notes: 1. Green and ROHS packaging
2.
Tape and reel with Dry-pack delivery.
3.
For Speed versus VCC,see Figure 22-1 on page 157.
Table 26-1. Package Type
Package Type
TU
14-lead, 0.150" wide body, plastic gull wing small outline package (SOIC)
PC
20-pad, 4  4  0.8mm body, quad flat no-lead/micro lead frame package (QFN/MLF)
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
187
27.
Packaging Information
27.1
PC
eee C
ccc C
DRAWINGS NOT SCALED
A
A1
D
E
Laser Mark for Pin 1
Identification in this Area
Seating Plane
B
C
Top View
Side View
D2
COMMON DIMENSIONS
6
(Unit of Measure = mm)
10
11
0.35
5
E2
15
1
Pin1 ID
20
e
16
L
b
SYMBOL
MIN
NOM
MAX
A
0.70
0.75
0.80
A1
D/E
0.00
3.90
0.02
4.00
0.05
4.10
D2/E2
2.50
2.60
2.70
L
0.35
0.45
0.55
b
0.20
0.25
0.30
e
0.50 BSC
ccc
Tolerances of Form and Position
0.10
eee
0.08
n
See Option A, B
NOTE
20
Bottom View
Option A
Pin 1# Chamfer
(C 0.35 max)
Option B
Pin 1# Notch
(0.20 R)
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-220, Variation WGGD-5 for proper dimensions, tolerances, datums, etc.
(excepted D2/E2 Min et Nom.)
2. Dimensions b applies to metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip.
If the terminal has the optical radius on the other end of the terminal, the dimensions should not be measured in that radius area.
Package Drawing Contact:
[email protected]
188
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
08/01/14
TITLE
GPC
DRAWING NO.
REV.
PC, 20-Lds - 0.50mm Pitch, 4x4x0.8mm Body size
Very very Thin Quad Flat No Lead Package (WQFN) Sawn
ZVF
PC
J
27.2
TU
N
E
H
L
1
D
e
B
A1
A
E
MM
MIN
NOM
1.60
A
1.35
A1
0.10
B
0.33
D
E
INCH
MAX
MIN
NOM
MAX
.063
.069
1.75
.053
0.25
.004
0.41
0.51
.013
.016
.020
8.53
8.64
8.74
.336
.340
.344
3.80
3.91
3.99
.149
.154
.157
H
5.79
5.99
6.20
.228
.236
.244
L
0.40
0.71
1.27
.016
.028
.050
e
1.27 BSC
.010
.050 BSC
07/27/07
TITLE
Package Drawing Contact:
[email protected]
TU, 14 Lead, 0.150” Body Width
Plastic Gull Wing Small Outline Package (SOIC)
GPC
DRAWING NO.
REV.
TU
C
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
189
28.
Errata
The revision letter in this section refers to the revision of the Atmel® ATtiny24/44/84 Automotive device.
28.1
ATtiny24 Automotive
28.1.1 Rev. E
1.
28.2
No known errata.
ATtiny44 Automotive
28.2.1 Rev. D
1.
28.3
No known errata.
ATtiny84 Automotive
28.3.1 Rev. B
1.
190
No known errata.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
29.
Revision History
Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this
document.
Revision No.
7701G-AVR-02/15
7701F-AVR-10/12
7701E-AVR-02/11
7701D-AVR-09/10
History
Put datasheet in the latest template
Section 27 “Packaging Information” on pages 188 to 189 updated
Section 27 “Packaging Information” on page 214 updated.
MCUCR registers updated
BOD values updated.
Internal RC oscillator accuracy update.
See Section 7.6 “Calibrated Internal RC Oscillator” on page 27.
7701C-AVR-11/08
ADC characteristics update.
See Section 22.5 “ADC Characteristics – Preliminary Data” on page 159
DC characteristics update. See Table 22-1 on page 155.
Brown-out detector hysteresis See Table 22-4 on page 158.
Calibrated Internal RC Oscillator Accuracy update. See
Section 22-2 “Calibration Accuracy of Internal RC Oscillator” on page 157
DC Characteristics updated. Section 22. “Electrical Characteristics” on page 155.
7701B-AVR-09/07
7701A-AVR-05/07
ADC maximum resolution corrected.
Section 18. “Analog-to-Digital Converter” on page 118.
POR value updated. Table 9-1 on page 37.
Initial automotive version. Started from industrial specification document 8006 rev. E
09/06.
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
191
30.
Table of Contents
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.
Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1
2.
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1
2.2
2.3
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Automotive Quality Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.
Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.
About Code Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.
CPU Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
6.
7.
In-System Re-programmable Flash Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SRAM Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EEPROM Data Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Systems and their Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Default Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low-frequency Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibrated Internal RC Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
128kHz Internal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Clock Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
25
25
25
27
27
28
28
29
29
Power Management and Sleep Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
Sleep Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADC Noise Reduction Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software BOD Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Reduction Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimizing Power Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
16
16
17
20
21
System Clock and Clock Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
8.
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Architectural Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ALU – Arithmetic Logic Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
General Purpose Register File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Stack Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Instruction Execution Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reset and Interrupt Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.1
6.2
6.3
6.4
6.5
192
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
31
31
31
32
32
32
32
32
34
9.
System Control and Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.10
10.
49
50
54
61
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer/Counter Clock Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Counter Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Compare Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compare Match Output Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer/Counter Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
63
64
64
65
66
67
71
73
16-bit Timer/Counter1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
14.1
14.2
14.3
14.4
14.5
14.6
14.7
14.8
14.9
14.10
14.11
15.
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ports as General Digital I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alternate Port Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-bit Timer/Counter0 with PWM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
13.1
13.2
13.3
13.4
13.5
13.6
13.7
13.8
13.9
14.
Pin Change Interrupt Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
I/O Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
12.1
12.2
12.3
12.4
13.
Interrupt Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
External Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
11.1
11.2
12.
36
36
37
38
38
39
39
39
40
41
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
10.1
11.
Resetting the AVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-on Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brown-out Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timed Sequences for Changing the Configuration of the Watchdog Timer. . . . . . . . . . . . . .
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing 16-bit Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer/Counter Clock Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Counter Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Capture Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Compare Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compare Match Output Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer/Counter Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
78
78
80
83
84
84
86
88
89
95
97
Timer/Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
15.1
15.2
15.3
Prescaler Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
External Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
193
16.
USI – Universal Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
16.1
16.2
16.3
16.4
16.5
17.
Performing Page Erase by SPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filling the Temporary Buffer (Page Loading) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performing a Page Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Addressing the Flash During Self-Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Program And Data Memory Lock Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signature Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibration Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Downloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-voltage Serial Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-voltage Serial Programming Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed Grades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Characterizations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System and Reset Characterizations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADC Characteristics – Preliminary Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Programming Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High-voltage Serial Programming Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
135
135
135
136
136
136
137
137
137
138
140
141
142
143
143
144
144
148
149
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
22.1
22.2
22.3
22.4
22.5
22.6
22.7
194
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Break Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limitations of debugWIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
21.1
21.2
21.3
21.4
21.5
21.6
21.7
21.8
22.
118
118
120
120
121
124
124
128
128
129
Self-Programming the Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
20.1
20.2
20.3
20.4
20.5
21.
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADC Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting a Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prescaling and Conversion Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Channel or Reference Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADC Noise Canceller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADC Conversion Result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
debugWIRE On-chip Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
19.1
19.2
19.3
19.4
19.5
19.6
20.
Analog Comparator Multiplexed Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Analog-to-Digital Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
18.1
18.2
18.3
18.4
18.5
18.6
18.7
18.8
18.9
18.10
19.
105
105
106
111
111
Analog Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
17.1
17.2
18.
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alternative USI Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Register Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
155
157
157
158
159
161
162
23.
Typical Characteristics – Preliminary Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
23.1
23.2
23.3
23.4
23.5
23.6
23.7
23.8
23.9
23.10
23.11
Active Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply Current of IO modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-down Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Pull-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Driver Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Threshold and Hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BOD Threshold and Analog Comparator Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Oscillator Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current Consumption of Peripheral Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current Consumption in Reset and Reset Pulse Width . . . . . . . . . . . . . . . . . . . . . . . . . . .
163
166
168
168
169
171
172
175
176
178
180
24.
Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
25.
Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
26.
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
26.1
27.
Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
27.1
27.2
28.
ATtiny24/44/84. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
TU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Errata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
28.1
28.2
28.3
ATtiny24 Automotive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
ATtiny44 Automotive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
ATtiny84 Automotive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
29.
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
30.
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
ATtiny24/44/84 [DATASHEET]
7701G–AVR–02/15
195
XXXXXX
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2015 Atmel Corporation. / Rev.: 7701G–AVR–02/15
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR®, AVR Studio ®, and others are registered trademarks or trademarks of Atmel
Corporation in U.S. and other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.