Features • • • • • • • • • • High Performance, Low Power Atmel®AVR® 8-Bit Microcontroller Advanced RISC Architecture – 130 Powerful Instructions – Most Single Clock Cycle Execution – 32 x 8 General Purpose Working Registers – Fully Static Operation – Up to 20MIPS Throughput at 20MHz – On-Chip 2-cycle Multiplier High Endurance Non-volatile Memory segments – In-System Self-programmable Flash Program Memory • 32KBytes – EEPROM • 1Kbytes – Internal SRAM • 2Kbytes – Write/Erase cyles: 10,000 Flash/100,000 EEPROM – Data retention: 20 years at 85°C/100 years at 25°C(1) – Optional Boot Code Section with Independent Lock Bits • In-System Programming by On-chip Boot Program • True Read-While-Write Operation – Programming Lock for Software Security JTAG (IEEE std. 1149.1 compliant) Interface – Boundary-scan Capabilities According to the JTAG Standard – Extensive On-chip Debug Support – Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface Peripheral Features – 4 x 25 Segment LCD Driver (ATmega329P) – 4 x 40 Segment LCD Driver (ATmega3290P) – Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode – One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode – Real Time Counter with Separate Oscillator – Four PWM Channels – 8-channel, 10-bit ADC – Programmable Serial USART – Master/Slave SPI Serial Interface – Universal Serial Interface with Start Condition Detector – Programmable Watchdog Timer with Separate On-chip Oscillator – On-chip Analog Comparator – Interrupt and Wake-up on Pin Change Special Microcontroller Features – Power-on Reset and Programmable Brown-out Detection – Internal Calibrated Oscillator – External and Internal Interrupt Sources – Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and Standby I/O and Packages – 54/69 Programmable I/O Lines – 64/100-lead TQFP, 64-pad QFN/MLF Speed Grade: – ATmega329P/ATmega3290P: • 0 - 16MHz @ 1.8 - 5.5V, • 0 - 20MHz @ 2.7 - 5.5V Temperature range: – -40°C to 85°C Industrial Ultra-Low Power Consumption – Active Mode: • 420μA at 1MHz, 1.8V – Power-down Mode: • 40nA at 1.8V – Power-save Mode: • 750nA at 1.8V 8-bit Atmel Microcontroller with 32KBytes In-System Programmable Flash ATmega329P ATmega3290P Preliminary Summary 8021HS–AVR–07/2015 ATmega329P/3290P 1. Pin Configurations LCDCAP 1 (RXD/PCINT0) PE0 2 AVCC GND AREF PF0 (ADC0) PF1 (ADC1) PF2 (ADC2) PF3 (ADC3) PF4 (ADC4/TCK) PF5 (ADC5/TMS) PF6 (ADC6/TDO) PF7 (ADC7/TDI) GND VCC PA0 (COM0) PA1 (COM1) PA2 (COM2) 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 MLF/ Pinout ATmega329P 64 Figure 1-1. 48 PA3 (COM3) 47 PA4 (SEG0) INDEX CORNER (SCK/PCINT9) PB1 11 38 PC3 (SEG9) (MOSI/PCINT10) PB2 12 37 PC2 (SEG10) (MISO/PCINT11) PB3 13 36 PC1 (SEG11) (OC0A/PCINT12) PB4 14 35 PC0 (SEG12) (OC1A/PCINT13) PB5 15 34 PG1 (SEG13) (OC1B/PCINT14) PB6 16 33 PG0 (SEG14) Note: (SEG15) PD7 32 39 PC4 (SEG8) (SEG16) PD6 31 10 (SEG17) PD5 30 (SS/PCINT8) PB0 29 40 PC5 (SEG7) (SEG18) PD4 9 28 (CLKO/PCINT7) PE7 (SEG19) PD3 41 PC6 (SEG6) 27 8 (SEG20) PD2 (DO/PCINT6) PE6 26 42 PC7 (SEG5) (INT0/SEG21) PD1 7 25 (DI/SDA/PCINT5) PE5 (ICP1/SEG22) PD0 43 PG2 (SEG4) 24 6 (TOSC1) XTAL1 (USCK/SCL/PCINT4) PE4 23 44 PA7 (SEG3) (TOSC2) XTAL2 5 22 (AIN1/PCINT3) PE3 GND 45 PA6 (SEG2) VCC 21 4 RESET/PG5 20 (XCK/AIN0/PCINT2) PE2 (T0/SEG23) PG4 19 46 PA5 (SEG1) (T1/SEG24) PG3 18 3 (OC2A/PCINT15) PB7 17 (TXD/PCINT1) PE1 The large center pad underneath the QFN/MLF packages is made of metal and internally connected to GND. It should be soldered or glued to the board to ensure good mechanical stability. If the center pad is left unconnected, the package might loosen from the board. 2 8021HS–AVR–07/2015 ATmega329P/3290P LCDCAP 1 (RXD/PCINT0) PE0 2 (TXD/PCINT1) PE1 3 (XCK/AIN0/PCINT2) PE2 (AIN1/PCINT3) PE3 AVCC AGND AREF PF0 (ADC0) PF1 (ADC1) PF2 (ADC2) PF3 (ADC3) PF4 (ADC4/TCK) PF5 (ADC5/TMS) PF6 (ADC6/TDO) PF7 (ADC7/TDI) DNC DNC PH7 (PCINT23/SEG36) PH6 (PCINT22/SEG37) PH5 (PCINT21/SEG38) PH4 (PCINT20/SEG39) DNC DNC GND VCC DNC PA0 (COM0) PA1 (COM1) PA2 (COM2) 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 TQFP / Pinout ATmega3290P 100 Figure 1-2. 75 PA3 (COM3) 74 PA4 (SEG0) 73 PA5 (SEG1) 4 72 PA6 (SEG2) 5 71 PA7 (SEG3) (USCK/SCL/PCINT4) PE4 6 70 PG2 (SEG4) (DI/SDA/PCINT5) PE5 7 69 PC7 (SEG5) (DO/PCINT6) PE6 8 68 PC6 (SEG6) (CLKO/PCINT7) PE7 9 67 DNC VCC 10 66 PH3 (PCINT19/SEG7) GND 11 65 PH2 (PCINT18/SEG8) DNC 12 64 PH1 (PCINT17/SEG9) (PCINT24/SEG35) PJ0 13 63 PH0 (PCINT16/SEG10) (PCINT25/SEG34) PJ1 14 62 DNC DNC 15 61 DNC DNC 16 60 DNC DNC 17 59 DNC DNC 18 58 PC5 (SEG11) (SS/PCINT8) PB0 19 57 PC4 (SEG12) (SCK/PCINT9) PB1 20 56 PC3 (SEG13) (MOSI/PCINT10) PB2 21 55 PC2 (SEG14) (MISO/PCINT11) PB3 22 54 PC1 (SEG15) (OC0A/PCINT12) PB4 23 53 PC0 (SEG16) (OC1A/PCINT13) PB5 24 52 PG1 (SEG17) (OC1B/PCINT14) PB6 25 51 PG0 (SEG18) 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 (OC2A/PCINT15) PB7 DNC (T1/SEG33) PG3 (T0/SEG32) PG4 RESET/PG5 VCC GND (TOSC2) XTAL2 (TOSC1) XTAL1 DNC DNC (PCINT26/SEG31) PJ2 (PCINT27/SEG30) PJ3 (PCINT28/SEG29) PJ4 (PCINT29/SEG28) PJ5 (PCINT30/SEG27) PJ6 DNC (ICP1/SEG26) PD0 (INT0/SEG25) PD1 (SEG24) PD2 (SEG23) PD3 (SEG22) PD4 (SEG21) PD5 (SEG20) PD6 (SEG19) PD7 INDEX CORNER 3 8021HS–AVR–07/2015 ATmega329P/3290P 2. Overview The ATmega329P/3290P is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega329P/3290P achieves throughputs approaching 1MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. Block Diagram GND Block Diagram PF0 - PF7 VCC PA0 - PA7 DATA DIR. REG. PORTF DATA REGISTER PORTF PC0 - PC7 PORTA DRIVERS PORTF DRIVERS PORTC DRIVERS DATA DIR. REG. PORTA DATA REGISTER PORTA XTAL2 Figure 2-1. XTAL1 2.1 DATA REGISTER PORTC DATA DIR. REG. PORTC 8-BIT DATA BUS AVCC AGND CALIB. OSC ADC INTERNAL OSCILLATOR AREF WATCHDOG TIMER ON-CHIP DEBUG PROGRAM FLASH SRAM MCU CONTROL REGISTER BOUNDARYSCAN INSTRUCTION REGISTER TIMING AND CONTROL LCD CONTROLLER/ DRIVER TIMER/ COUNTERS GENERAL PURPOSE REGISTERS X PROGRAMMING LOGIC INSTRUCTION DECODER CONTROL LINES + - INTERRUPT UNIT ALU EEPROM STATUS REGISTER AVR CPU ANALOG COMPARATOR Z Y RESET DATA DIR. REG. PORTH DATA REGISTER PORTH JTAG TAP STACK POINTER DATA DIR. REG. PORTJ DATA REGISTER PORTJ PORTH DRIVERS PORTJ DRIVERS PJ0 - PJ6 PH0 - PH7 OSCILLATOR PROGRAM COUNTER USART UNIVERSAL SERIAL INTERFACE DATA REGISTER PORTE DATA DIR. REG. PORTE PORTE DRIVERS PE0 - PE7 SPI DATA REGISTER PORTB DATA DIR. REG. PORTB PORTB DRIVERS PB0 - PB7 DATA REGISTER PORTD DATA DIR. REG. PORTD PORTD DRIVERS PD0 - PD7 DATA REG. PORTG DATA DIR. REG. PORTG PORTG DRIVERS PG0 - PG4 The Atmel® AVR® core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The 4 8021HS–AVR–07/2015 ATmega329P/3290P resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The ATmel®AVR® ATmega329P/3290P provides the following features: 32K bytes of In-System Programmable Flash with Read-While-Write capabilities, 1Kbytes EEPROM, 2Kbyte SRAM, 54/69 general purpose I/O lines, 32 general purpose working registers, a JTAG interface for Boundary-scan, On-chip Debugging support and programming, a complete On-chip LCD controller with internal contrast control, three flexible Timer/Counters with compare modes, internal and external interrupts, a serial programmable USART, Universal Serial Interface with Start Condition Detector, an 8-channel, 10-bit ADC, a programmable Watchdog Timer with internal Oscillator, an SPI serial port, and five software selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt system to continue functioning. The Power-down mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next interrupt or hardware reset. In Power-save mode, the asynchronous timer and the LCD controller continues to run, allowing the user to maintain a timer base and operate the LCD display while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O modules except asynchronous timer, LCD controller and ADC, to minimize switching noise during ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low-power consumption. The device is manufactured using Atmel’s high density non-volatile memory technology. The On-chip In-System re-Programmable (ISP) Flash allows the program memory to be reprogrammed In-System through an SPI serial interface, by a conventional non-volatile memory programmer, or by an On-chip Boot program running on the AVR core. The Boot program can use any interface to download the application program in the Application Flash memory. Software in the Boot Flash section will continue to run while the Application Flash section is updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATmega329P/3290P is a powerful microcontroller that provides a highly flexible and cost effective solution to many embedded control applications. The ATmega329P/3290P AVR is supported with a full suite of program and system development tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators, In-Circuit Emulators, and Evaluation kits. 2.2 Comparison between ATmega329P, and ATmega3290P. The ATmega329P, and ATmega3290P differ only in pin count and pinout. Table 2-1 on page 5 summarizes the different configurations for the four devices. Table 2-1. Configuration Summary Device Flash EEPROM RAM LCD Segments General Purpose I/O Pins ATmega329P 32Kbytes 1Kbytes 2Kbytes 4 x 25 54 ATmega3290P 32Kbytes 1Kbytes 2Kbytes 4 x 40 69 5 8021HS–AVR–07/2015 ATmega329P/3290P 2.3 Pin Descriptions The following section describes the I/O-pin special functions. 2.3.1 VCC Digital supply voltage. 2.3.2 GND Ground. 2.3.3 Port A (PA7...PA0) Port A is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port A output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port A pins that are externally pulled low will source current if the pull-up resistors are activated. The Port A pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port A also serves the functions of various special features of the ATmega329P/3290P as listed on page 71. 2.3.4 Port B (PB7...PB0) Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port B has better driving capabilities than the other ports. Port B also serves the functions of various special features of the ATmega329P/3290P as listed on page 72. 2.3.5 Port C (PC7...PC0) Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port C also serves the functions of special features of the ATmega329P/3290P as listed on page 75. 2.3.6 Port D (PD7...PD0) Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D also serves the functions of various special features of the ATmega329P/3290P as listed on page 76. 6 8021HS–AVR–07/2015 ATmega329P/3290P 2.3.7 Port E (PE7...PE0) Port E is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port E output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port E pins that are externally pulled low will source current if the pull-up resistors are activated. The Port E pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port E also serves the functions of various special features of the ATmega329P/3290P as listed on page 78. 2.3.8 Port F (PF7...PF0) Port F serves as the analog inputs to the A/D Converter. Port F also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins can provide internal pull-up resistors (selected for each bit). The Port F output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port F pins that are externally pulled low will source current if the pull-up resistors are activated. The Port F pins are tri-stated when a reset condition becomes active, even if the clock is not running. If the JTAG interface is enabled, the pull-up resistors on pins PF7(TDI), PF5(TMS), and PF4(TCK) will be activated even if a reset occurs. Port F also serves the functions of the JTAG interface. 2.3.9 Port G (PG5...PG0) Port G is a 6-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port G output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port G pins that are externally pulled low will source current if the pull-up resistors are activated. The Port G pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port G also serves the functions of various special features of the ATmega329P/3290P as listed on page 82. 2.3.10 Port H (PH7...PH0) Port H is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port H output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port H pins that are externally pulled low will source current if the pull-up resistors are activated. The Port H pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port H also serves the functions of various special features of the ATmega3290P as listed on page 84. 2.3.11 Port J (PJ6...PJ0) Port J is a 7-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port J output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port J pins that are externally pulled low will source current if the pull-up resistors are activated. The Port J pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port J also serves the functions of various special features of the ATmega3290P as listed on page 87. 7 8021HS–AVR–07/2015 ATmega329P/3290P 2.3.12 RESET Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not running. The minimum pulse length is given in ”System and Reset Characteristics” on page 336. Shorter pulses are not guaranteed to generate a reset. 2.3.13 XTAL1 Input to the inverting Oscillator amplifier and input to the internal clock operating circuit. 2.3.14 XTAL2 Output from the inverting Oscillator amplifier. 2.3.15 AVCC AVCC is the supply voltage pin for Port F and the A/D Converter. It should be externally connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter. 2.3.16 AREF This is the analog reference pin for the A/D Converter. 2.3.17 LCDCAP An external capacitor (typical > 470nF) must be connected to the LCDCAP pin as shown in Figure 23-2, if the LCD module is enabled and configured to use internal power. This capacitor acts as a reservoir for LCD power (VLCD). A large capacitance reduces ripple on VLCD but increases the time until VLCD reaches its target value. 8 8021HS–AVR–07/2015 ATmega329P/3290P 3. Resources A comprehensive set of development tools, application notes and datasheets are available for download on http://www.atmel.com/avr. Note: 1. 4. Data Retention Reliability Qualification results show that the projected data retention failure rate is much less than 1 PPM over 20 years at 85°C or 100 years at 25°C. 5. About Code Examples This documentation contains simple code examples that briefly show how to use various parts of the device. These code examples assume that the part specific header file is included before compilation. Be aware that not all C compiler vendors include bit definitions in the header files and interrupt handling in C is compiler dependent. Please confirm with the C compiler documentation for more details. For I/O Registers located in extended I/O map, “IN”, “OUT”, “SBIS”, “SBIC”, “CBI”, and “SBI” instructions must be replaced with instructions that allow access to extended I/O. Typically “LDS” and “STS” combined with “SBRS”, “SBRC”, “SBR”, and “CBR”. 9 8021HS–AVR–07/2015 ATmega329P/3290P 6. Register Summary Note: Address Name Registers with bold type only available in ATmega3290P. Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (0xFF) LCDDR19 SEG339 SEG338 SEG337 SEG336 SEG335 SEG334 SEG333 SEG332 Page 247 (0xFE) LCDDR18 SEG331 SEG330 SEG329 SEG328 SEG327 SEG326 SEG325 SEG324 247 (0xFD) LCDDR17 SEG323 SEG322 SEG321 SEG320 SEG319 SEG318 SEG317 SEG316 247 (0xFC) LCDDR16 SEG315 SEG314 SEG313 SEG312 SEG311 SEG310 SEG309 SEG308 247 (0xFB) LCDDR15 SEG307 SEG306 SEG305 SEG304 SEG303 SEG302 SEG301 SEG300 247 (0xFA) LCDDR14 SEG239 SEG238 SEG237 SEG236 SEG235 SEG234 SEG233 SEG232 247 (0xF9) LCDDR13 SEG231 SEG230 SEG229 SEG228 SEG227 SEG226 SEG225 SEG224 247 (0xF8) LCDDR12 SEG223 SEG222 SEG221 SEG220 SEG219 SEG218 SEG217 SEG216 247 (0xF7) LCDDR11 SEG215 SEG214 SEG213 SEG212 SEG211 SEG210 SEG209 SEG208 247 (0xF6) LCDDR10 SEG207 SEG206 SEG205 SEG204 SEG203 SEG202 SEG201 SEG200 247 (0xF5) LCDDR09 SEG139 SEG138 SEG137 SEG136 SEG135 SEG134 SEG133 SEG132 247 (0xF4) LCDDR08 SEG131 SEG130 SEG129 SEG128 SEG127 SEG126 SEG125 SEG124 247 (0xF3) LCDDR07 SEG123 SEG122 SEG121 SEG120 SEG119 SEG118 SEG117 SEG116 247 (0xF2) LCDDR06 SEG115 SEG114 SEG113 SEG112 SEG111 SEG110 SEG109 SEG108 247 (0xF1) LCDDR05 SEG107 SEG106 SEG105 SEG104 SEG103 SEG102 SEG101 SEG100 247 (0xF0) LCDDR04 SEG039 SEG038 SEG037 SEG036 SEG035 SEG034 SEG033 SEG032 247 (0xEF) LCDDR03 SEG031 SEG030 SEG029 SEG028 SEG027 SEG026 SEG025 SEG024 247 247 (0xEE) LCDDR02 SEG023 SEG022 SEG021 SEG020 SEG019 SEG018 SEG017 SEG016 (0xED) LCDDR01 SEG015 SEG014 SEG013 SEG012 SEG011 SEG010 SEG009 SEG008 247 (0xEC) LCDDR00 SEG007 SEG006 SEG005 SEG004 SEG003 SEG002 SEG001 SEG000 247 (0xEB) Reserved - - - - - - - - (0xEA) Reserved - - - - - - - - (0xE9) Reserved - - - - - - - - (0xE8) Reserved - - - - - - - - (0xE7) LCDCCR LCDDC2 LCDDC1 LCDDC0 LCDMDT LCDCC3 LCDCC2 LCDCC1 LCDCC0 245 (0xE6) LCDFRR - LCDPS2 LCDPS1 LCDPS0 - LCDCD2 LCDCD1 LCDCD0 243 (0xE5) LCDCRB LCDCS LCD2B LCDMUX1 LCDMUX0 LCDPM3 LCDPM2 LCDPM1 LCDPM0 242 (0xE4) LCDCRA LCDEN LCDAB - LCDIF LCDIE LCDBD LCDCCD LCDBL 241 (0xE3) Reserved - - - - - - - - (0xE2) Reserved - - - - - - - - (0xE1) Reserved - - - - - - - - (0xE0) Reserved - - - - - - - - (0xDF) Reserved - - - - - - - - (0xDE) Reserved - - - - - - - - (0xDD) PORTJ - PORTJ6 PORTJ5 PORTJ4 PORTJ3 PORTJ2 PORTJ1 PORTJ0 93 (0xDC) DDRJ - DDJ6 DDJ5 DDJ4 DDJ3 DDJ2 DDJ1 DDJ0 93 (0xDB) PINJ - PINJ6 PINJ5 PINJ4 PINJ3 PINJ2 PINJ1 PINJ0 93 (0xDA) PORTH PORTH7 PORTH6 PORTH5 PORTH4 PORTH3 PORTH2 PORTH1 PORTH0 92 (0xD9) DDRH DDH7 DDH6 DDH5 DDH4 DDH3 DDH2 DDH1 DDH0 93 (0xD8) PINH PINH7 PINH6 PINH5 PINH4 PINH3 PINH2 PINH1 PINH0 93 (0xD7) Reserved - - - - - - - - (0xD6) Reserved - - - - - - - - (0xD5) Reserved - - - - - - - - (0xD4) Reserved - - - - - - - - (0xD3) Reserved - - - - - - - - (0xD2) Reserved - - - - - - - - (0xD1) Reserved - - - - - - - - (0xD0) Reserved - - - - - - - - (0xCF) Reserved - - - - - - - - (0xCE) Reserved - - - - - - - - (0xCD) Reserved - - - - - - - - (0xCC) Reserved - - - - - - - - (0xCB) Reserved - - - - - - - - (0xCA) Reserved - - - - - - - - (0xC9) Reserved - - - - - - - - (0xC8) Reserved - - - - - - - - (0xC7) Reserved - - - - - - - - (0xC6) UDR0 (0xC5) UBRR0H USART0 Data Register 189 USART0 Baud Rate Register High 193 10 8021HS–AVR–07/2015 ATmega329P/3290P Address Name (0xC4) UBRR0L (0xC3) Reserved (0xC2) (0xC1) (0xC0) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 USART0 Baud Rate Register Low - - UCSR0C - UMSEL0 UCSR0B RXCIE0 TXCIE0 UCSR0A RXC0 TXC0 - Page 193 - - - - - UPM01 UPM00 USBS0 UCSZ01 UCSZ00 UCPOL0 UDRIE0 RXEN0 TXEN0 UCSZ02 RXB80 TXB80 190 UDRE0 FE0 DOR0 UPE0 U2X0 MPCM0 189 191 (0xBF) Reserved - - - - - - - - (0xBE) Reserved - - - - - - - - (0xBD) Reserved - - - - - - - - (0xBC) Reserved - - - - - - - - (0xBB) Reserved - - - - - - - - (0xBA) USIDR (0xB9) USISR USISIF USIOIF USIPF USIDC USICNT3 USICNT2 USICNT1 USICNT0 206 (0xB8) USICR USISIE USIOIE USIWM1 USIWM0 USICS1 USICS0 USICLK USITC 207 (0xB7) Reserved - - - - - - - - (0xB6) ASSR - - - EXCLK AS2 TCN2UB OCR2UB TCR2UB (0xB5) Reserved - - - - - - - - (0xB4) Reserved - - - - - - - - (0xB3) OCR2A Timer/Counter 2 Output Compare Register A (0xB2) TCNT2 Timer/Counter2 (0xB1) Reserved - - - - - - - - USI Data Register 206 157 157 157 (0xB0) TCCR2A FOC2A WGM20 COM2A1 COM2A0 WGM21 CS22 CS21 CS20 (0xAF) Reserved - - - - - - - - 155 (0xAE) Reserved - - - - - - - - (0xAD) Reserved - - - - - - - - (0xAC) Reserved - - - - - - - - (0xAB) Reserved - - - - - - - - (0xAA) Reserved - - - - - - - - (0xA9) Reserved - - - - - - - - (0xA8) Reserved - - - - - - - - (0xA7) Reserved - - - - - - - - (0xA6) Reserved - - - - - - - - (0xA5) Reserved - - - - - - - - (0xA4) Reserved - - - - - - - - (0xA3) Reserved - - - - - - - - (0xA2) Reserved - - - - - - - - (0xA1) Reserved - - - - - - - - (0xA0) Reserved - - - - - - - - (0x9F) Reserved - - - - - - - - (0x9E) Reserved - - - - - - - - (0x9D) Reserved - - - - - - - - (0x9C) Reserved - - - - - - - - (0x9B) Reserved - - - - - - - - (0x9A) Reserved - - - - - - - - (0x99) Reserved - - - - - - - - (0x98) Reserved - - - - - - - - (0x97) Reserved - - - - - - - - (0x96) Reserved - - - - - - - - (0x95) Reserved - - - - - - - - (0x94) Reserved - - - - - - - - (0x93) Reserved - - - - - - - - (0x92) Reserved - - - - - - - - (0x91) Reserved - - - - - - - - (0x90) Reserved - - - - - - - - (0x8F) Reserved - - - - - - - - (0x8E) Reserved - - - - - - - - (0x8D) Reserved - - - - - - - - (0x8C) Reserved - - - - - - - - (0x8B) OCR1BH Timer/Counter1 Output Compare Register B High (0x8A) OCR1BL Timer/Counter1 Output Compare Register B Low 131 (0x89) OCR1AH Timer/Counter1 Output Compare Register A High 131 (0x88) OCR1AL Timer/Counter1 Output Compare Register A Low 131 (0x87) ICR1H Timer/Counter1 Input Capture Register High 132 (0x86) ICR1L Timer/Counter1 Input Capture Register Low 132 131 11 8021HS–AVR–07/2015 ATmega329P/3290P Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page (0x85) TCNT1H Timer/Counter1 High (0x84) TCNT1L Timer/Counter1 Low (0x83) Reserved - - - (0x82) TCCR1C FOC1A FOC1B - - - - - - 130 (0x81) TCCR1B ICNC1 ICES1 - WGM13 WGM12 CS12 CS11 CS10 129 - - 131 131 - - - (0x80) TCCR1A COM1A1 COM1A0 COM1B1 COM1B0 - - WGM11 WGM10 127 (0x7F) DIDR1 - - - - - - AIN1D AIN0D 212 ADC7D ADC6D ADC5D ADC4D ADC3D ADC2D ADC1D ADC0D 229 - - - - - - - - (0x7E) DIDR0 (0x7D) Reserved (0x7C) ADMUX REFS1 REFS0 ADLAR MUX4 MUX3 MUX2 MUX1 MUX0 225 (0x7B) ADCSRB - ACME - - - ADTS2 ADTS1 ADTS0 211/228 (0x7A) ADCSRA ADEN ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 (0x79) ADCH (0x78) ADCL (0x77) Reserved - - - - - - - - (0x76) Reserved - - - - - - - - (0x75) Reserved - - - - - - - - (0x74) Reserved - - - - - - - - (0x73) PCMSK3 - PCINT30 PCINT29 PCINT28 PCINT27 PCINT26 PCINT25 PCINT24 (0x72) Reserved - - - - - - - - (0x71) Reserved - - - - - - - - (0x70) TIMSK2 - - - - - - OCIE2A TOIE2 (0x6F) TIMSK1 - - ICIE1 - - OCIE1B OCIE1A TOIE1 132 (0x6E) TIMSK0 - - - - - - OCIE0A TOIE0 139 (0x6D) PCMSK2 PCINT23 PCINT22 PCINT21 PCINT20 PCINT19 PCINT18 PCINT17 PCINT16 62 (0x6C) PCMSK1 PCINT15 PCINT14 PCINT13 PCINT12 PCINT11 PCINT10 PCINT9 PCINT8 62 (0x6B) PCMSK0 PCINT7 PCINT6 PCINT5 PCINT4 PCINT3 PCINT2 PCINT1 PCINT0 62 (0x6A) Reserved - - - - - - - - (0x69) EICRA - - - - - - ISC01 ISC00 (0x68) Reserved - - - - - - - - (0x67) Reserved - - - - - - - - (0x66) OSCCAL (0x65) Reserved - - - - - - - - (0x64) PRR - - - PRLCD PRTIM1 PRSPI PSUSART0 PRADC (0x63) Reserved - - - - - - - - (0x62) Reserved - - - - - - - - (0x61) CLKPR CLKPCE - - - CLKPS3 CLKPS2 CLKPS1 CLKPS0 35 (0x60) WDTCR - - - WDCE WDE WDP2 WDP1 WDP0 50 0x3F (0x5F) SREG I T H S V N Z C 0x3E (0x5E) SPH 0x3D (0x5D) SPL 0x3C (0x5C) Reserved - - - - - - - - 0x3B (0x5B) Reserved - - - - - - - - 0x3A (0x5A) Reserved - - - - - - - - 0x39 (0x59) Reserved - - - - - - - - 0x38 (0x58) Reserved - - - - - - - - 0x37 (0x57) SPMCSR SPMIE RWWSB - RWWSRE BLBSET PGWRT PGERS SPMEN 294 0x36 (0x56) Reserved 57/90/280 ADC Data Register High 227 228 ADC Data Register Low 228 Oscillator Calibration Register [CAL7...0] 62 158 59 35 Stack Pointer High 43 12 14 Stack Pointer Low 14 0x35 (0x55) MCUCR JTD BODS BODSE PUD - - IVSEL IVCE 0x34 (0x54) MCUSR - - - JTRF WDRF BORF EXTRF PORF 50 0x33 (0x53) SMCR - - - - SM2 SM1 SM0 SE 42 0x32 (0x52) Reserved - - - - - - - - 0x31 (0x51) OCDR IDRD/OCDR7 OCDR6 OCDR5 OCDR4 OCDR3 OCDR2 OCDR1 OCDR0 253 0x30 (0x50) ACSR ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 211 0x2F (0x4F) Reserved - - - - - - - - 0x2E (0x4E) SPDR 0x2D (0x4D) SPSR SPIF WCOL - - SPI Data Register - - - SPI2X 169 168 0x2C (0x4C) SPCR SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 167 0x2B (0x4B) GPIOR2 General Purpose I/O Register 0x2A (0x4A) GPIOR1 General Purpose I/O Register 0x29 (0x49) Reserved - - - 0x28 (0x48) Reserved - - - 0x27 (0x47) OCR0A 26 26 - - - - - - - - - - Timer/Counter0 Output Compare A 139 12 8021HS–AVR–07/2015 ATmega329P/3290P Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 2 Bit 1 Bit 0 - - - - COM0A0 WGM01 CS02 CS01 CS00 136 - - - PSR2 PSR10 140/159 - - - 0x26 (0x46) TCNT0 0x25 (0x45) Reserved - - - - 0x24 (0x44) TCCR0A FOC0A WGM00 COM0A1 0x23 (0x43) GTCCR TSM - - 0x22 (0x42) EEARH - - - 0x21 (0x41) EEARL Bit 3 Timer/Counter0 Page 138 EEPROM Address Register High EEPROM Address Register Low 22 22 0x20 (0x40) EEDR 0x1F (0x3F) EECR EEPROM Data Register 0x1E (0x3E) GPIOR0 0x1D (0x3D) EIMSK PCIE PCIE2 PCIE1 PCIE0 - - - INT0 60 0x1C (0x3C) EIFR PCIF3 PCIF2 PCIF1 PCIF0 - - - INTF0 61 0x1B (0x3B) Reserved - - - - - - - - 0x1A (0x3A) Reserved - - - - - - - - 0x19 (0x39) Reserved - - - - - - - - 0x18 (0x38) Reserved - - - - - - - - 0x17 (0x37) TIFR2 - - - - - - OCF2A TOV2 0x16 (0x36) TIFR1 - - ICF1 - - OCF1B OCF1A TOV1 133 0x15 (0x35) TIFR0 - - - - - - OCF0A TOV0 140 0x14 (0x34) PORTG - - - PORTG4 PORTG3 PORTG2 PORTG1 PORTG0 92 0x13 (0x33) DDRG - - - DDG4 DDG3 DDG2 DDG1 DDG0 92 0x12 (0x32) PING - - PING5 PING4 PING3 PING2 PING1 PING0 92 0x11 (0x31) PORTF PORTF7 PORTF6 PORTF5 PORTF4 PORTF3 PORTF2 PORTF1 PORTF0 92 0x10 (0x30) DDRF DDF7 DDF6 DDF5 DDF4 DDF3 DDF2 DDF1 DDF0 92 - - - - EERIE 22 EEMWE EEWE EERE General Purpose I/O Register 23 26 159 0x0F (0x2F) PINF 0x0E (0x2E) PORTE 0x0D (0x2D) DDRE DDE7 DDE6 DDE5 DDE4 DDE3 DDE2 0x0C (0x2C) PINE PINE7 PINE6 PINE5 PINE4 PINE3 PINE2 0x0B (0x2B) PORTD PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 91 0x0A (0x2A) DDRD DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 91 0x09 (0x29) PIND PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 91 0x08 (0x28) PORTC PORTC7 PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 91 0x07 (0x27) DDRC DDC7 DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 91 0x06 (0x26) PINC PINC7 PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 91 0x05 (0x25) PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 90 0x04 (0x24) DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 90 0x03 (0x23) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 90 0x02 (0x22) PORTA PORTA7 PORTA6 PORTA5 PORTA4 PORTA3 PORTA2 PORTA1 PORTA0 90 0x01 (0x21) DDRA DDA7 DDA6 DDA5 DDA4 DDA3 DDA2 DDA1 DDA0 90 0x00 (0x20) PINA PINA7 PINA6 PINA5 PINA4 PINA3 PINA2 PINA1 PINA0 90 Notes: PINF7 PINF6 PINF5 PINF4 PINF3 PINF2 PINF1 PINF0 92 PORTE7 PORTE6 PORTE5 PORTE4 PORTE3 PORTE2 PORTE1 PORTE0 91 DDE1 DDE0 91 PINE1 PINE0 92 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. 2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the value of single bits can be checked by using the SBIS and SBIC instructions. 3. Some of the Status Flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI instructions will only operate on the specified bit, and can therefore be used on registers containing such Status Flags. The CBI and SBI instructions work with registers 0x00 to 0x1F only. 4. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. The ATmega329P/3290P is a complex microcontroller with more peripheral units than can be supported within the 64 location reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from 0x60 - 0xFF in SRAM, only the ST/STS/STD and LD/LDS/LDD instructions can be used. 13 8021HS–AVR–07/2015 ATmega329P/3290P 7. Instruction Set Summary Mnemonics Operands Description Operation Flags #Clocks ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers Rd Rd + Rr Z,C,N,V,H ADC Rd, Rr Add with Carry two Registers Rd Rd + Rr + C Z,C,N,V,H 1 ADIW Rdl,K Add Immediate to Word Rdh:Rdl Rdh:Rdl + K Z,C,N,V,S 2 SUB Rd, Rr Subtract two Registers Rd Rd - Rr Z,C,N,V,H 1 SUBI Rd, K Subtract Constant from Register Rd Rd - K Z,C,N,V,H 1 SBC Rd, Rr Subtract with Carry two Registers Rd Rd - Rr - C Z,C,N,V,H 1 SBCI Rd, K Subtract with Carry Constant from Reg. Rd Rd - K - C Z,C,N,V,H 1 SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl Rdh:Rdl - K Z,C,N,V,S 2 AND Rd, Rr Logical AND Registers Rd Rd Rr Z,N,V 1 ANDI Rd, K Logical AND Register and Constant Rd Rd K Z,N,V 1 OR Rd, Rr Logical OR Registers Rd Rd v Rr Z,N,V 1 1 ORI Rd, K Logical OR Register and Constant Rd Rd v K Z,N,V 1 EOR Rd, Rr Exclusive OR Registers Rd Rd Rr Z,N,V 1 COM Rd One’s Complement Rd 0xFF Rd Z,C,N,V 1 NEG Rd Two’s Complement Rd 0x00 Rd Z,C,N,V,H 1 SBR Rd,K Set Bit(s) in Register Rd Rd v K Z,N,V 1 CBR Rd,K Clear Bit(s) in Register Rd Rd (0xFF - K) Z,N,V 1 INC Rd Increment Rd Rd + 1 Z,N,V 1 DEC Rd Decrement Rd Rd 1 Z,N,V 1 TST Rd Test for Zero or Minus Rd Rd Rd Z,N,V 1 CLR Rd Clear Register Rd Rd Rd Z,N,V 1 SER Rd Set Register Rd 0xFF None 1 MUL Rd, Rr Multiply Unsigned R1:R0 Rd x Rr Z,C 2 MULS Rd, Rr Multiply Signed R1:R0 Rd x Rr Z,C 2 MULSU Rd, Rr Multiply Signed with Unsigned R1:R0 Rd x Rr Z,C 2 FMUL Rd, Rr Fractional Multiply Unsigned R1:R0 (Rd x Rr) << 1 Z,C 2 FMULS Rd, Rr Fractional Multiply Signed R1:R0 (Rd x Rr) << 1 Z,C 2 FMULSU Rd, Rr Fractional Multiply Signed with Unsigned R1:R0 (Rd x Rr) << 1 Z,C 2 Relative Jump PC PC + k + 1 None 2 Indirect Jump to (Z) PC Z None 2 3 BRANCH INSTRUCTIONS RJMP k IJMP JMP k Direct Jump PC k None RCALL k Relative Subroutine Call PC PC + k + 1 None 3 Indirect Call to (Z) PC Z None 3 ICALL Direct Subroutine Call PC k None 4 RET Subroutine Return PC STACK None 4 RETI Interrupt Return PC STACK I Compare, Skip if Equal if (Rd = Rr) PC PC + 2 or 3 None CALL CPSE k Rd,Rr 4 1/2/3 CP Rd,Rr Compare Rd Rr Z, N,V,C,H 1 CPC Rd,Rr Compare with Carry Rd Rr C Z, N,V,C,H 1 CPI Rd,K Compare Register with Immediate Rd K Z, N,V,C,H SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC PC + 2 or 3 None 1/2/3 SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC PC + 2 or 3 None 1/2/3 SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC PC + 2 or 3 None 1/2/3 SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC PC + 2 or 3 None 1/2/3 1 BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PCPC+k + 1 None 1/2 BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PCPC+k + 1 None 1/2 BREQ k Branch if Equal if (Z = 1) then PC PC + k + 1 None 1/2 BRNE k Branch if Not Equal if (Z = 0) then PC PC + k + 1 None 1/2 BRCS k Branch if Carry Set if (C = 1) then PC PC + k + 1 None 1/2 BRCC k Branch if Carry Cleared if (C = 0) then PC PC + k + 1 None 1/2 BRSH k Branch if Same or Higher if (C = 0) then PC PC + k + 1 None 1/2 BRLO k Branch if Lower if (C = 1) then PC PC + k + 1 None 1/2 BRMI k Branch if Minus if (N = 1) then PC PC + k + 1 None 1/2 BRPL k Branch if Plus if (N = 0) then PC PC + k + 1 None 1/2 BRGE k Branch if Greater or Equal, Signed if (N V= 0) then PC PC + k + 1 None 1/2 BRLT k Branch if Less Than Zero, Signed if (N V= 1) then PC PC + k + 1 None 1/2 BRHS k Branch if Half Carry Flag Set if (H = 1) then PC PC + k + 1 None 1/2 BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC PC + k + 1 None 1/2 BRTS k Branch if T Flag Set if (T = 1) then PC PC + k + 1 None 1/2 BRTC k Branch if T Flag Cleared if (T = 0) then PC PC + k + 1 None 1/2 BRVS k Branch if Overflow Flag is Set if (V = 1) then PC PC + k + 1 None 1/2 14 8021HS–AVR–07/2015 ATmega329P/3290P Mnemonics Operands Description Operation Flags #Clocks BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC PC + k + 1 None BRIE k Branch if Interrupt Enabled if ( I = 1) then PC PC + k + 1 None 1/2 BRID k Branch if Interrupt Disabled if ( I = 0) then PC PC + k + 1 None 1/2 1/2 BIT AND BIT-TEST INSTRUCTIONS SBI P,b Set Bit in I/O Register I/O(P,b) 1 None 2 CBI P,b Clear Bit in I/O Register I/O(P,b) 0 None 2 LSL Rd Logical Shift Left Rd(n+1) Rd(n), Rd(0) 0 Z,C,N,V 1 LSR Rd Logical Shift Right Rd(n) Rd(n+1), Rd(7) 0 Z,C,N,V 1 ROL Rd Rotate Left Through Carry Rd(0)C,Rd(n+1) Rd(n),CRd(7) Z,C,N,V 1 ROR Rd Rotate Right Through Carry Rd(7)C,Rd(n) Rd(n+1),CRd(0) Z,C,N,V 1 ASR Rd Arithmetic Shift Right Rd(n) Rd(n+1), n=0..6 Z,C,N,V 1 SWAP Rd Swap Nibbles Rd(3..0)Rd(7..4),Rd(7..4)Rd(3..0) None 1 1 BSET s Flag Set SREG(s) 1 SREG(s) BCLR s Flag Clear SREG(s) 0 SREG(s) 1 BST Rr, b Bit Store from Register to T T Rr(b) T 1 BLD Rd, b Bit load from T to Register Rd(b) T None 1 SEC Set Carry C1 C 1 CLC Clear Carry C0 C 1 SEN Set Negative Flag N1 N 1 CLN Clear Negative Flag N0 N 1 SEZ Set Zero Flag Z1 Z 1 CLZ Clear Zero Flag Z0 Z 1 SEI Global Interrupt Enable I1 I 1 CLI Global Interrupt Disable I 0 I 1 SES Set Signed Test Flag S1 S 1 CLS Clear Signed Test Flag S0 S 1 SEV Set Twos Complement Overflow. V1 V 1 CLV Clear Twos Complement Overflow V0 V 1 SET Set T in SREG T1 T 1 CLT Clear T in SREG T0 T 1 SEH CLH Set Half Carry Flag in SREG Clear Half Carry Flag in SREG H1 H0 H H 1 1 DATA TRANSFER INSTRUCTIONS MOV Rd, Rr Move Between Registers 1 Rd, Rr Copy Register Word Rd Rr Rd+1:Rd Rr+1:Rr None MOVW None 1 LDI Rd, K Load Immediate Rd K None 1 LD Rd, X Load Indirect Rd (X) None 2 LD Rd, X+ Load Indirect and Post-Inc. Rd (X), X X + 1 None 2 LD Rd, - X Load Indirect and Pre-Dec. X X - 1, Rd (X) None 2 LD Rd, Y Load Indirect Rd (Y) None 2 LD Rd, Y+ Load Indirect and Post-Inc. Rd (Y), Y Y + 1 None 2 LD Rd, - Y Load Indirect and Pre-Dec. Y Y - 1, Rd (Y) None 2 LDD Rd,Y+q Load Indirect with Displacement Rd (Y + q) None 2 LD Rd, Z Load Indirect Rd (Z) None 2 LD Rd, Z+ Load Indirect and Post-Inc. Rd (Z), Z Z+1 None 2 LD Rd, -Z Load Indirect and Pre-Dec. Z Z - 1, Rd (Z) None 2 LDD Rd, Z+q Load Indirect with Displacement Rd (Z + q) None 2 LDS Rd, k Load Direct from SRAM Rd (k) None 2 ST X, Rr Store Indirect (X) Rr None 2 ST X+, Rr Store Indirect and Post-Inc. (X) Rr, X X + 1 None 2 ST - X, Rr Store Indirect and Pre-Dec. X X - 1, (X) Rr None 2 2 ST Y, Rr Store Indirect (Y) Rr None ST Y+, Rr Store Indirect and Post-Inc. (Y) Rr, Y Y + 1 None 2 ST - Y, Rr Store Indirect and Pre-Dec. Y Y - 1, (Y) Rr None 2 STD Y+q,Rr Store Indirect with Displacement (Y + q) Rr None 2 ST Z, Rr Store Indirect (Z) Rr None 2 ST Z+, Rr Store Indirect and Post-Inc. (Z) Rr, Z Z + 1 None 2 ST -Z, Rr Store Indirect and Pre-Dec. Z Z - 1, (Z) Rr None 2 STD Z+q,Rr Store Indirect with Displacement (Z + q) Rr None 2 STS k, Rr Store Direct to SRAM (k) Rr None 2 Load Program Memory R0 (Z) None 3 LPM LPM Rd, Z Load Program Memory Rd (Z) None 3 LPM Rd, Z+ Load Program Memory and Post-Inc Rd (Z), Z Z+1 None 3 Store Program Memory (Z) R1:R0 None - IN Rd, P In Port Rd P None 1 OUT P, Rr Out Port P Rr None 1 SPM 15 8021HS–AVR–07/2015 ATmega329P/3290P Mnemonics Operands Description Operation Flags #Clocks PUSH Rr Push Register on Stack STACK Rr None 2 POP Rd Pop Register from Stack Rd STACK None 2 MCU CONTROL INSTRUCTIONS NOP No Operation None 1 SLEEP Sleep (see specific descr. for Sleep function) None 1 WDR BREAK Watchdog Reset Break (see specific descr. for WDR/timer) For On-chip Debug Only None None 1 N/A 16 8021HS–AVR–07/2015 ATmega329P/3290P 8. Ordering Information 8.1 ATmega329P Speed (MHz)(3) 10 20 20 Notes: Power Supply Ordering Code(2) Package Type(1) 1.8 - 5.5V ATmega329PV-10AU ATmega329PV-10AUR(4) ATmega329PV-10MU ATmega329PV-10MUR(4) 64A 64A 64M1 64M1 2.7 - 5.5V ATmega329P-20AU ATmega329P-20AUR(4) ATmega329P-20MU ATmega329P-20MUR(4) 64A 64A 64M1 64M1 1.8 - 5.5V ATmega329P-20AN ATmega329P-20ANR(4) ATmega329P-20MN ATmega329P-20MNR(4) 64A 64A 64M1 64M1 Operational Range Industrial (-40C to 85C) Extended (-40C to 105C)(5) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. 3. For Speed vs. VCC see Figure 28-2 on page 334 and Figure 28-3 on page 334. 4. Tape & Reel 5. See Appendix A ATmega169PA/329P/3290P 105°C Package Type 64A 64-lead, 14 x 14 x 1.0 mm, Thin Profile Plastic Quad Flat Package (TQFP) 64M1 64-pad, 9 x 9 x 1.0 mm, Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF) 17 8021HS–AVR–07/2015 ATmega329P/3290P 8.2 ATmega3290P Speed (MHz)(3) 10 20 20 Notes: Power Supply Ordering Code(2) 1.8 - 5.5V ATmega3290PV-10AU ATmega3290PV-10AUR(4) 2.7 - 5.5V ATmega3290P-20AU ATmega3290P-20AUR(4) 1.8 - 5.5V ATmega3290P-20AN ATmega3290P-20ANR(4) ATmega3290P-20MN ATmega3290P-20MNR(4) Package Type(1) 100A 64A 64A 64M1 64M1 Operational Range Industrial (-40C to 85C) Extended (-40C to 105C)(5) 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. 3. For Speed vs. VCC see Figure 28-2 on page 334 and Figure 28-3 on page 334. 4. Tape & Reel 5. See Appendix A ATmega169PA/329P/3290P 105°C Package Type 100A 100-lead, 14 x 14 x 1.0 mm, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) 18 8021HS–AVR–07/2015 ATmega329P/3290P 9. Packaging Information 9.1 64A PIN 1 B e PIN 1 IDENTIFIER E1 E D1 D C 0°~7° A1 A2 A L COMMON DIMENSIONS (Unit of measure = mm) Notes: 1.This package conforms to JEDEC reference MS-026, Variation AEB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10mm maximum. SYMBOL MIN NOM MAX A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 15.75 16.00 16.25 D1 13.90 14.00 14.10 E 15.75 16.00 16.25 13.90 14.00 14.10 E1 B 0.30 – C 0.09 L 0.45 e NOTE Note 2 Note 2 0.45 – 0.20 – 0.75 0.80 TYP 2010-10-20 2325 Orchard Parkway San Jose, CA 95131 TITLE 64A, 64-lead, 14 x 14mm Body Size, 1.0mm Body Thickness, 0.8mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. 64A REV. C 19 8021HS–AVR–07/2015 ATmega329P/3290P 9.2 64M1 D Marked Pin# 1 ID E C SEATING PLANE A1 TOP VIEW A K 0.08 C L Pin #1 Corner D2 1 2 3 Option A SIDE VIEW Pin #1 Triangle COMMON DIMENSIONS (Unit of Measure = mm) E2 Option B Pin #1 Chamfer (C 0.30) SYMBOL MIN NOM MAX A 0.80 0.90 1.00 A1 b K Option C b e BOTTOM VIEW Notes: Pin #1 Notch (0.20 R) – 0.02 0.05 0.18 0.25 0.30 D 8.90 9.00 9.10 D2 5.20 5.40 5.60 E 8.90 9.00 9.10 E2 5.20 5.40 5.60 e NOTE 0.50 BSC L 0.35 0.40 0.45 K 1.25 1.40 1.55 1. JEDEC Standard MO-220, (SAW Singulation) Fig. 1, VMMD. 2. Dimension and tolerance conform to ASMEY14.5M-1994. 2010-10-19 2325 Orchard Parkway San Jose, CA 95131 TITLE 64M1, 64-pad, 9 x 9 x 1.0 mm Body, Lead Pitch 0.50 mm, 5.40 mm Exposed Pad, Micro Lead Frame Package (MLF) DRAWING NO. 64M1 REV. H 20 8021HS–AVR–07/2015 ATmega329P/3290P 9.3 100A PIN 1 B PIN 1 IDENTIFIER E1 e E D1 D C 0°~7° A1 A2 A L COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-026, Variation AED. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.08mm maximum. SYMBOL MIN NOM MAX A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 15.75 16.00 16.25 D1 13.90 14.00 14.10 E 15.75 16.00 16.25 E1 13.90 14.00 14.10 B 0.17 – 0.27 C 0.09 – 0.20 L 0.45 – 0.75 e NOTE Note 2 Note 2 0.50 TYP 2014-02-05 100A, 100-lead, 14 x 14mm Body Size, 1.0mm Body Thickness, 0.5mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) 100A E 21 8021HS–AVR–07/2015 ATmega329P/3290P 10. Errata 10.1 ATmega329P rev. A • Interrupts may be lost when writing the timer registers in the asynchronous timer • Using BOD disable will make the chip reset 1. Interrupts may be lost when writing the timer registers in the asynchronous timer The interrupt will be lost if a timer register that is synchronous timer clock is written when the asynchronous Timer/Counter register (TCNTx) is 0x00. Problem Fix/ Workaround Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor 0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx). 2. Using BOD disable will make the chip reset If the part enters sleep with the BOD turned off with the BOD disable option enabled, a BOD reset will be generated at wakeup and the chip will reset. Problem Fix/Workaround Do not use BOD disable 10.2 ATmega329P rev. B • Interrupts may be lost when writing the timer registers in the asynchronous timer 1. Interrupts may be lost when writing the timer registers in the asynchronous timer The interrupt will be lost if a timer register that is synchronous timer clock is written when the asynchronous Timer/Counter register (TCNTx) is 0x00. Problem Fix/ Workaround Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor 0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx). 10.3 ATmega329P rev. C • Interrupts may be lost when writing the timer registers in the asynchronous timer 1. Interrupts may be lost when writing the timer registers in the asynchronous timer The interrupt will be lost if a timer register that is synchronous timer clock is written when the asynchronous Timer/Counter register (TCNTx) is 0x00. Problem Fix/ Workaround Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor 0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx). 22 8021HS–AVR–07/2015 ATmega329P/3290P 10.4 ATmega3290P rev. A • Interrupts may be lost when writing the timer registers in the asynchronous timer • Using BOD disable will make the chip reset 1. Interrupts may be lost when writing the timer registers in the asynchronous timer The interrupt will be lost if a timer register that is synchronous timer clock is written when the asynchronous Timer/Counter register (TCNTx) is 0x00. Problem Fix/ Workaround Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor 0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx). 2. Using BOD disable will make the chip reset If the part enters sleep with the BOD turned off with the BOD disable option enabled, a BOD reset will be generated at wakeup and the chip will reset. Problem Fix/Workaround Do not use BOD disable 10.5 ATmega3290P rev. B • Interrupts may be lost when writing the timer registers in the asynchronous timer 1. Interrupts may be lost when writing the timer registers in the asynchronous timer The interrupt will be lost if a timer register that is synchronous timer clock is written when the asynchronous Timer/Counter register (TCNTx) is 0x00. Problem Fix/ Workaround Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor 0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx). 10.6 ATmega3290P rev. C • Interrupts may be lost when writing the timer registers in the asynchronous timer 1. Interrupts may be lost when writing the timer registers in the asynchronous timer The interrupt will be lost if a timer register that is synchronous timer clock is written when the asynchronous Timer/Counter register (TCNTx) is 0x00. Problem Fix/ Workaround Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor 0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx). 23 8021HS–AVR–07/2015 ATmega329P/3290P 11. Datasheet Revision History Refer to the complete datasheet for revision history. 24 8021HS–AVR–07/2015 Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2015 Atmel Corporation. / Rev.: Atmel-8021HS-AVR-ATmega329P-3290P_Datasheet_07/2015. Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR® and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade. 8021HS–AVR–07/2015