AT89LP51/52 - Complete

Features
• 8-bit Microcontroller Compatible with 8051 Products
• Enhanced 8051 Architecture
•
•
•
•
•
– Single Clock Cycle per Byte Fetch
– 12 Clock per Machine Cycle Compatibility Mode
– Up to 20 MIPS Throughput at 20 MHz Clock Frequency
– Fully Static Operation: 0 Hz to 20 MHz
– On-chip 2-cycle Hardware Multiplier
– 256 x 8 Internal RAM
– External Data/Program Memory Interface
– Dual Data Pointers
– 4-level Interrupt Priority
Nonvolatile Program and Data Memory
– 4K/8K Bytes of In-System Programmable (ISP) Flash Program Memory
– 256 Bytes of Flash Data Memory
– 256-byte User Signature Array
– Endurance: 10,000 Write/Erase Cycles
– Serial Interface for Program Downloading
– 64-byte Fast Page Programming Mode
– 3-level Program Memory Lock for Software Security
– In-Application Programming of Program Memory
Peripheral Features
– Three 16-bit Timer/Counters with Clock Out Modes
– Enhanced UART
• Automatic Address Recognition
• Framing Error Detection
• SPI and TWI Emulation Modes
– Programmable Watchdog Timer with Software Reset and Prescaler
Special Microcontroller Features
– Brown-out Detection and Power-on Reset with Power-off Flag
– Selectable Polarity External Reset Pin
– Low Power Idle and Power-down Modes
– Interrupt Recovery from Power-down Mode
– Internal 1.8432 MHz Auxiliary Oscillator
I/O and Packages
– Up to 36 Programmable I/O Lines
– Green (Pb/Halide-free) Packages
• 40-lead PDIP
• 44-lead TQFP/PLCC
• 44-pad VQFN/MLF
– Configurable Port Modes (per 8-bit port)
• Quasi-bidirectional (80C51 Style)
• Input-only (Tristate)
• Push-pull CMOS Output
• Open-drain
Operating Conditions
– 2.4V to 5.5V VCC Voltage Range
– -40° C to 85°C Temperature Range
– 0 to 20 MHz @ 2.4V–5.5V
– 0 to 25 MHz @ 4.5V–5.5V
8-bit
Microcontroller
with 4K/8K
Bytes In-System
Programmable
Flash
AT89LP51
AT89LP52
3709D–MICRO–12/11
1. Pin Configurations
1.1
40-lead PDIP
(T2) P1.0
(T2 EX) P1.1
P1.2
P1.3
P1.4
(MOSI) P1.5
(MISO) P1.6
(SCK) P1.7
RST
(RXD) P3.0
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
(WR) P3.6
(RD) P3.7
(XTAL2) P4.1
(XTAL1) P4.0
GND
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
VCC
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
POL
P4.2 (ALE)
P4.3 (PSEN)
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
P2.4 (A12)
P2.3 (A11)
P2.2 (A10)
P2.1 (A9)
P2.0 (A8)
44-lead TQFP
44
43
42
41
40
39
38
37
36
35
34
P1.4
P1.3
P1.2
P1.1 (T2 EX)
P1.0 (T2)
*NC
VCC
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
1.2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
33
32
31
30
29
28
27
26
25
24
23
1
2
3
4
5
6
7
8
9
10
11
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
POL
*NC
P4.4 (ALE)
P4.5 (PSEN)
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
(WR) P3.6
(RD) P3.7
(XTAL2) P4.7
(XTAL1) P4.6
GND
*NC
(A8) P2.0
(A9) P2.1
(A10) P2.2
(A11) P2.3
(A12) P2.4
12
13
14
15
16
17
18
19
20
21
22
(MOSI) P1.5
(MISO) P1.6
(SCK) P1.7
RST
(RXD) P3.0
*NC
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
2
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
44-lead PLCC
6
5
4
3
2
1
44
43
42
41
40
P1.4
P1.3
P1.2
P1.1 (T2 EX)
P1.0 (T2)
*NC
VCC
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
1.3
7
8
9
10
11
12
13
14
15
16
17
39
38
37
36
35
34
33
32
31
30
29
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
POL
*NC
P4.4 (ALE)
P4.5 (PSEN)
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
(WR) P3.6
(RD) P3.7
(XTAL2) P4.7
(XTAL1) P4.6
GND
*NC
(A8) P2.0
(A9) P2.1
(A10) P2.2
(A11) P2.3
(A12) P2.4
18
19
20
21
22
23
24
25
26
27
28
(MOSI) P1.5
(MISO) P1.6
(SCK) P1.7
RST
(RXD) P3.0
*NC
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
44-pad VQFN/QFN/MLF
44
43
42
41
40
39
38
37
36
35
34
P1.4
P1.3
P1.2
P1.1/T2EX
P1.0/T2
*NC
VDD
P0.0/AD0
P0.1/AD1
P0.2/AD2
P0.3/AD3
1.4
33
32
31
30
29
28
27
26
25
24
23
NOTE:
Bottom pad
should be
soldered to ground
P0.4/AD4
P0.5/AD5
P0.6/AD6
P0.7/AD7
POL
*NC
P4.4/ALE
P4.5/PSEN
P2.7/A15
P2.6/A14
P2.5/A13
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
8
9
10
11
WR/P3.6
RD/P3.7
XTAL2/P4.7
XTAL1/P4.6
GND
*NC
A8/P2.0
A9/P2.1
A10/P2.2
A11/P2.3
A12/P2.4
MOSI/P1.5
MISO/P1.6
SCK/P1.7
RST
RXD/P3.0
*NC
TXD/P3.1
INT0/P3.2
INT1/P3.3
T0/P3.4
T1/P3.5
3
3709D–MICRO–12/11
1.5
Pin Description
Table 1-1.
AT89LP51/52 Pin Description
Pin Number
4
TQFP
PLCC
PDIP
VQFN
Symbol
Type
1
7
6
1
P1.5
I/O
I/O
P1.5: I/O Port 1 bit 5.
MOSI: SPI master-out/slave-in. In UART SPI mode this pin is an output. During InSystem Programming, this pin is an input.
2
8
7
2
P1.6
I/O
I/O
P1.6: I/O Port 1 bit 6.
MISO: SPI master-in/slave-out. In UART SPI mode this pin is an input. During InSystem Programming, this pin is an output.
3
9
8
3
P1.7
I/O
I/O
P1.7: I/O Port 1 bit 7.
SCK: SPI Clock. In UART SPI mode this pin is an output. During In-System
Programming, this pin is an input.
4
10
9
4
RST
5
11
10
5
P3.0
6
12
7
13
11
7
P3.1
8
14
12
8
9
15
13
10
16
11
I/O
Description
RST: External Reset input (Reset polarity depends on POL pin. See “External Reset”
on page 33.). The RST pin can output a pulse when the internal Watchdog reset is
active.
I/O
I
P3.0: I/O Port 3 bit 0.
RXD: Serial Port Receiver Input.
NC
Not internally connected
I/O
O
P3.1: I/O Port 3 bit 1.
TXD: Serial Port Transmitter Output.
P3.2
I/O
I
P3.2: I/O Port 3 bit 2.
INT0: External Interrupt 0 Input or Timer 0 Gate Input.
9
P3.3
I/O
I
P3.3: I/O Port 3 bit 3.
INT1: External Interrupt 1 Input or Timer 1 Gate Input
14
10
P3.4
I/O
P3.4: I/O Port 3 bit 4.
T1: Timer/Counter 0 External input or output.
17
15
1
P3.5
12
18
16
12
P3.6
13
19
17
13
P3.7
14
20
18
14
P4.7
I/O
O
6
I/O
I/O
I/O
I/O
O
I/O
O
15
21
19
15
P4.6
I/O
I
16
22
20
16
GND
I
17
23
18
24
21
18
19
25
22
20
26
23
17
P3.5: I/O Port 3 bit 5.
T1: Timer/Counter 1 External input or output.
P3.6: I/O Port 3 bit 6.
WR: External memory interface Write Strobe (active-low).
P3.7: I/O Port 3 bit 7.
RD: External memory interface Read Strobe (active-low).
P4.7: I/O Port 4 bit 7.
XTAL2: Output from inverting oscillator amplifier. It may be used as a port pin if the
internal RC oscillator or external clock is selected as the clock source.
P4.6: I/O Port 4 bit 6.
XTAL1: Input to the inverting oscillator amplifier and internal clock generation circuits.
It may be used as a port pin if the internal RC oscillator is selected as the clock
source.
Ground
NC
Not internally connected
P2.0
I/O
O
P2.0: I/O Port 2 bit 0.
A8: External memory interface Address bit 8.
19
P2.1
I/O
O
P2.1: I/O Port 2 bit 1.
A9: External memory interface Address bit 9.
20
P2.1
I/O
O
P2.2: I/O Port 2 bit 2.
A10: External memory interface Address bit 10.
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Table 1-1.
AT89LP51/52 Pin Description
Pin Number
TQFP
PLCC
PDIP
VQFN
Symbol
Type
21
27
24
21
P2.3
I/O
O
P2.3: I/O Port 2 bit 3.
A11: External memory interface Address bit 11.
22
28
25
22
P2.4
I/O
O
P2.4: I/O Port 2 bit 5.
A12: External memory interface Address bit 12.
23
29
26
23
P2.5
I/O
O
P2.5: I/O Port 2 bit 5.
A13: External memory interface Address bit 13.
24
30
27
24
P2.6
I/O
O
P2.6: I/O Port 2 bit 6.
A14: External memory interface Address bit 14.
25
31
28
25
P2.7
I/O
O
P2.7: I/O Port 2 bit 7.
A15: External memory interface Address bit 15.
26
32
29
26
P4.5
I/O
O
P4.5: I/O Port 4 bit 5.
PSEN: External memory interface Program Store Enable (active-low).
27
33
30
27
P4.4
I/O
O
P4.4: I/O Port 4 bit 4.
ALE: External memory interface Address Latch Enable.
28
34
NC
Not internally connected
29
35
31
29
POL
I
30
36
32
30
P0.7
I/O
I/O
P0.7: I/O Port 0 bit 7.
AD7: External memory interface Address/Data bit 7.
31
37
33
31
P0.6
I/O
I/O
P0.6: I/O Port 0 bit 6.
AD6: External memory interface Address/Data bit 6.
32
38
34
32
P0.5
I/O
I/O
P0.5: I/O Port 0 bit 5.
AD5: External memory interface Address/Data bit 5.
33
39
35
33
P0.4
I/O
I/O
P0.4: I/O Port 0 bit 4.
AD4: External memory interface Address/Data bit 4.
34
40
36
34
P0.3
I/O
I/O
P0.3: I/O Port 0 bit 3.
AD3: External memory interface Address/Data bit 3.
35
41
37
35
P0.2
I/O
I/O
P0.2: I/O Port 0 bit 2.
AD2: External memory interface Address/Data bit 2.
36
42
38
36
P0.1
I/O
I/O
P0.1: I/O Port 0 bit 1.
AD1: External memory interface Address/Data bit 1.
37
43
39
37
P0.0
I/O
I/O
P0.0: I/O Port 0 bit 0.
AD0: External memory interface Address/Data bit 0.
38
44
40
38
VDD
I
39
1
40
2
1
40
41
3
2
42
4
43
44
28
39
Description
POL: Reset polarity (See “External Reset” on page 33.)
Supply Voltage
NC
Not internally connected
P1.0
I/O
I/O
P1.0: I/O Port 1 bit 0.
T2: Timer 2 External Input or Clock Output.
41
P1.1
I/O
I
P1.1: I/O Port 1 bit 1.
T2EX: Timer 2 External Capture/Reload Input.
3
42
P1.2
I/O
P1.2: I/O Port 1 bit 2.
5
4
43
P1.3
I/O
P1.3: I/O Port 1 bit 3.
6
5
44
P1.4
I/O
P1.4: I/O Port 1 bit 4.
5
3709D–MICRO–12/11
2. Overview
The AT89LP51/52 is a low-power, high-performance CMOS 8-bit microcontroller with 4K/8K
bytes of In-System Programmable Flash program memory and 256 bytes of Flash data memory.
The device is manufactured using Atmel's high-density nonvolatile memory technology and is
compatible with the industry-standard 80C52 instruction set.
The AT89LP51/52 is built around an enhanced CPU core that can fetch a single byte from memory every clock cycle. In the classic 8051 architecture, each fetch requires 6 clock cycles, forcing
instructions to execute in 12, 24 or 48 clock cycles. In the AT89LP51/52 CPU, instructions need
only 1 to 4 clock cycles providing 6 to 12 times more throughput than the standard 8051. Seventy percent of instructions need only as many clock cycles as they have bytes to execute, and
most of the remaining instructions require only one additional clock. The enhanced CPU core is
capable of 20 MIPS throughput whereas the classic 8051 CPU can deliver only 4 MIPS at the
same current consumption. Conversely, at the same throughput as the classic 8051, the new
CPU core runs at a much lower speed and thereby greatly reducing power consumption and
EMI. The AT89LP51/52 also includes a compatibility mode that will enable classic 12 clock per
machine cycle operation for true timing compatibility with AT89S51/52.
The AT89LP51/52 provides the following standard features: 4K/8K bytes of In-System
Programmable Flash program memory, 256 bytes of Flash data memory, 256 bytes of RAM, up
to 36 I/O lines, three 16-bit timer/counters, a programmable watchdog timer, a full-duplex serial
port, an on-chip crystal oscillator, an internal 1.8432 MHz auxiliary oscillator, and a four-level,
six-vector interrupt system. A block diagram is shown in Figure 2-1.
Key Benefits:
• Full software and timing compatibility with AT89S52 means no changes to existing software,
including fetching from external ROM or read/write from/to external RAM
• Disable compatibility mode to achieve on average 9 times more throughput at the same
current consumption and frequency as AT89S52; or lower the clock frequency 9 times and
achieve the same speed as AT89S52 but with more than 5 times less current consumption
• Save even more power and the cost of a quartz crystal by using the internal 1.8432 MHz RC
oscillator, which is Vcc and temperature compensated well enough to ensure proper UART
serial communications. Together with the built-in POR and the BOD circuits, you do not need
any external components for AT89LP52 to provide the reset and clock functions
• All three timer/counters of the AT89LP51/52, Timer 0, Timer 1 and Timer 2, can be
configured to toggle a port pin on overflow for clock/waveform generation. Unlike AT89S51,
Timer 2 is also present on AT89LP51
• The enhanced full-duplex UART of the AT89LP51/52 includes Framing Error Detection and
Automatic Address Recognition. In addition, enhancements to Mode 0 allow hardware
accelerated emulation of a master SPI or TWI
• Use In-Application Programming to alter the built-in 8K Flash program memory while
executing the application, in effect making it possible to have programmable data tables
embedded in the program code. Or use the 256-byte Flash Data memory for nonvolatile data
storage
• Each 8-bit I/O port of the AT89LP51/52 can be independently configured in one of four
operating modes. In quasi-bidirectional mode, the port operates as in the classic 8051. In
input-only mode, the port is tristated. Push-pull output mode provides full CMOS drivers and
open-drain mode provides just a pull-down. Unlike other 8051s, this allows Port 0 to operate
with on-chip pull-ups if desired
6
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
2.1
Block Diagram
Figure 2-1.
AT89LP51/52 Block Diagram
4K/8K Bytes
Flash Code
256 Bytes
Flash Data
256 Bytes
RAM
XRAM
Interface
8051 Single Cycle CPU
with 12-cycle Compatibility
Crystal or
Resonator
2.2
Port 0
Configurable I/O
UART
Port 1
Configurable I/O
16-bit Timer 0
16-bit Timer 1
Port 2
Configurable I/O
16-bit Timer 2
Port 3
Configurable I/O
Watchdog
Timer
Port 4
Configurable I/O
POR
BOD
Configurable
Oscillator
RC Auxiliary
Oscillator
System Configuration
The AT89LP51/52 supports several system configuration options. Nonvolatile options are set
through user fuses that must be programmed through the flash programming interface. Volatile
options are controlled by software through individual bits of special function registers (SFRs).
The AT89LP51/52 must be properly configured before correct operation can occur.
2.2.1
Fuse Options
Table 2-1 lists the fusable options for the AT89LP51/52. These options maintain their state even
when the device is powered off, but can only be changed with an external device programmer.
For more information, see Section 17.7 “User Configuration Fuses” on page 86.
7
3709D–MICRO–12/11
Table 2-1.
User Configuration Fuses
Fuse Name
Description
Clock Source
Selects between the High Speed Crystal Oscillator, Low Speed
Crystal Oscillator, External Clock or Internal RC Oscillator for the
source of the system clock.
Start-up Time
Selects time-out delay for the POR/BOD/PWD wake-up period.
Compatibility Mode
Configures the CPU in 12-clock Compatibility mode or single-cycle
Fast mode
In-System Programming Enable
Enables or disables In-System Programming.
User Signature Programming
Enables or disables programming of User Signature array.
Tristate Ports
Configures the default port state as input-only mode (tristated) or
quasi-bidirectional mode (weakly pulled high).
In-Application Programming
Enables or disables In-Application (self) Programming
R1 Enable
2.2.2
Software Options
Table 2-2 lists some important software configuration bits that affect operation at the system
level. These can be changed by the application software but are set to their default values upon
any reset. Most peripherals also have multipe configuration bits that are not listed here.
Table 2-2.
2.3
Important Software Configuration Bits
Bit(s)
SFR Location
Description
PxM0
PxM1
PMOD
Configures the I/O mode of all pins of Port x to be nput-only, quasibidirectional, push-pull output or open-drain. The default state is
controlled by the Default Port State fuse above
CDV2-0
CLKREG.3-1
Selects the division ratio between the oscillator and the system clock
TPS3-0
CLKREG.7-4
Selects the division ratio between the system clock and the timers
DISALE
AUXR.0
Enables/disables toggling of ALE
EXRAM
AUXR.1
Enables/disables access to on-chip memories that are mapped to the
external data memory address space
WS1-0
AUXR.3-2
Selects the number of wait states when accessing external data
memory
DMEN
MEMCON.3
Enables/disables access to the on-chip flash data memory
IAP
MEMCON.7
Enbles/disables the self programming feature when the fuse allows
Comparison to AT89S51/52
The AT89LP51/52 is part of a family of devices with enhanced features that are fully binary compatible with the 8051 instruction set. The AT89LP51/52 has two modes of operations,
Compatibility mode and Fast mode. In Compatibility mode the instruction timing, peripheral
behavior, SFR addresses, bit assignments and pin functions are identical to Atmel's existing
AT89S51/52 product. Additional enhancements are transparent to the user and can be used if
desired. Fast mode allows greater performance, but with some differences in behavior. The
major enhancements from the AT89S51/52 are outlined in the following paragraphs and may be
useful to users migrating to the AT89LP51/52 from older devices. A summary of the differences
between Compatibility and Fast modes is given in Table 2-3 on page 10. See also the Application note “Migrating from AT89S52 to AT89LP52.”
8
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
2.3.1
Instruction Execution
In Compatibility mode the AT89LP51/52 CPU uses the six-state machine cycle of the standard
8051 where instruction bytes are fetched every three system clock cycles. Execution times in
this mode are identical to AT89S51/52. For greater performance the user can enable Fast mode
by disabling the Compatibility fuse. In Fast mode the CPU fetches one code byte from memory
every clock cycle instead of every three clock cycles. This greatly increases the throughput of
the CPU. Each standard instruction executes in only 1 to 4 clock cycles. See “Instruction Set
Summary” on page 75 for more details. Any software delay loops or instruction-based timing
operations may need to be retuned to achieve the desired results in Fast mode.
2.3.2
System Clock
By default in Compatibility mode the system clock frequency is divided by 2 from the externally
supplied XTAL1 frequency for compatibility with standard 8051s (12 clocks per machine cycle).
The System Clock Divider can scale the system clock versus the oscillator source (See Section
6.4 on page 31). The divide-by-2 can be disabled to operate in X2 mode (6 clocks per machine
cycle) or the clock may be further divided to reduce the operating frequency. In Fast mode the
clock divider defaults to divide by 1.
The system clock source is selectable between the crystal oscillator, an externally driven clock
and an internal 1.8432 MHz auxiliary oscillator. See “System Clock” on page 29 and “User Configuration Fuses” on page 86.
2.3.3
Reset
The RST pin of the AT89LP51/52 has selectable polarity using the POL pin (formerly EA). When
POL is high the RST pin is active high with a pull-down resistor and when POL is low the RST
pin is active low with a pull-up resistor. For existing AT89S51/52 sockets where EA is tied to
VDD, replacing AT89S51/52 with AT89LP51/52 will maintain the active high reset. Note that
forcing external execution by tying EA low is not supported.
The AT89LP51/52 includes an on-chip Power-On Reset and Brown-out Detector circuit that
ensures that the device is reset from system power up. In most cases a RC startup circuit is not
required on the RST pin, reducing system cost, and the RST pin may be left unconnected if a
board-level reset is not present.
2.3.4
Timer/Counters
A common prescaler is available to divide the time base for Timer 0, Timer 1, Timer 2 and the
WDT. The TPS3-0 bits in the CLKREG SFR control the prescaler (Table 6-2 on page 31). In
Compatibility mode TPS3-0 defaults to 0101B, which causes the timers to count once every
machine cycle. The counting rate can be adjusted linearly from the system clock rate to 1/16 of
the system clock rate by changing TPS3-0. In Fast mode TPS3-0 defaults to 0000B, or the system
clock rate. TPS does not affect Timer 2 in Clock Out or Baud Generator modes.
In Compatibility mode the sampling of the external Timer/Counter pins: T0, T1, T2 and T2EX;
and the external interrupt pins, INT0 and INT1, is also controlled by the prescaler. In Fast mode
these pins are always sampled at the system clock rate.
Both Timer 0 and Timer 1 can toggle their respective counter pins, T0 and T1, when they overflow by setting the output enable bits in TCONB.
The Watchdog Timer includes a 7-bit prescaler for longer timeout periods than the AT89S51/52.
Note that in Fast Mode the WDIDLE and DISRTO bits are located in WDTCON and not in
AUXR.
9
3709D–MICRO–12/11
2.3.5
Interrupt Handling
With the addition of the IPH register, the AT89LP51/52 provides four levels of interrupt priority
for greater flexibility in handling multiple interrupts. Also, Fast mode allows for faster interrupt
response due to the shorter instruction execution times.
2.3.6
Serial Port
The timer prescaler increases the range of achievable baud rates when using Timer 1 to generate the baud rate in UART Modes 1 or 3, including an increase in the maximum baud rate
available in Compatibility mode. Additional features include automatic address recognition and
framing error detection.
The shift register mode (Mode 0) has been enhanced with more control of the polarity, phase
and frequency of the clock and full-duplex operation. This allows emulation of master serial
pheriperal (SPI) and two-wire (TWI) interfaces.
2.3.7
I/O Ports
The P0, P1, P2 and P3 I/O ports of the AT89LP51/52 may be configured in four different modes.
The default setting depends on the Tristate-Port User Fuse (See Section 17.7 on page 86).
When the fuse is set all the I/O ports revert to input-only (tristated) mode at power-up or reset.
When the fuse is not active, ports P1, P2 and P3 start in quasi-bidirectional mode and P0 starts
in open-drain mode. P4 always operates in quasi-bidirectional mode. P0 can be configured to
have internal pull-ups by placing it in quasi-bidirectional or output modes. This can reduce system cost by removing the need for external pull-ups on Port 0.
The P4.4–P4.7 pins are additional I/Os that replace the normally dedicated ALE, PSEN, XTAL1
and XTAL2 pins of the AT89S51/52. These pins can be used as additional I/Os depending on
the configuration of the clock and external memory.
2.3.8
Security
The AT89LP51/52 does not support the extenal access pin (EA). Therefore it is not possible to
execute from external program memory in address range 0000H–1FFFH. When the third Lockbit
is enabled (Lock Mode 4) external program execution is disabled for all addresses above
1FFFH. This differs from AT89S51/52 where Lock Mode 4 prevents EA from being sampled low,
but may still allow external execution at addresses outside the 8K internal space.
2.3.9
Programming
The AT89LP51/52 supports a richer command set for In-System Programming (ISP). Existing
AT89S51/52 programmers should be able to program the AT89LP51/52 in byte mode. In page
mode the AT89LP51/52 only supports programming of a half-page of 64 bytes and therefore
requires an extra address byte as compared to AT89S51/52. Furthermore the device signature
is located at addresses 0000H, 0001H and 0003H instead of 0000H, 0100H and 0200H.
Table 2-3.
Compatibility Mode versus Fast Mode Summary
Feature
Compatibility
Fast
3
1
6, 12, 18 or 24
1, 2, 3, 4 or 5
Default System Clock Divisor
2
1
Default Timer Prescaler Divisor
6
1
Instruction Fetch in System Clocks
Instruction Execution Time in System Clocks
10
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Table 2-3.
Compatibility Mode versus Fast Mode Summary
Feature
Compatibility
Fast
Pin Sampling Rate (INT0, INT1, T0, T1, T2, T2EX)
Prescaler Rate
System Clock
12
2
AUXR
WDTCON
Minimum RST input pulse in System Clocks
WDIDLE and DISRTO bit locations
3. Memory Organization
The AT89LP51/52 uses a Harvard Architecture with separate address spaces for program and
data memory. The program memory has a regular linear address space with support for 64K
bytes of directly addressable application code. The data memory has 256 bytes of internal RAM
and 128 bytes of Special Function Register I/O space. The AT89LP51/52 supports up to 64K
bytes of external data memory, with portions of the external data memory space implemented on
chip as nonvolatile Flash data memory. External program memory is supported for addresses
above 8K. The memory address spaces of the AT89LP51/52 are listed in Table 3-1.
Table 3-1.
3.1
AT89LP51/52 Memory Address Spaces
Name
Description
Range
DATA
Directly addressable internal RAM
00H–7FH
IDATA
Indirectly addressable internal RAM and stack space
00H–FFH
SFR
Directly addressable I/O register space
80H–FFH
FDATA
On-chip nonvolatile Flash data memory
0000H–00FFH
XDATA
External data memory
0100H–FFFFH
CODE
On-chip nonvolatile Flash program memory
0000H–0FFFH (AT89LP51)
0000H–1FFFH (AT89LP52)
XCODE
External program memory
2000H–FFFFH (AT89LP51)
1000H–FFFFH (AT89LP52)
SIG
On-chip nonvolatile Flash signature array
0000H–01FFH
Program Memory
The AT89LP51/52 contains 4K/8K bytes of on-chip In-System Programmable Flash memory for
program storage, plus support for up to 60K/56K bytes of external program memory. The Flash
memory has an endurance of at least 10,000 write/erase cycles and a minimum data retention
time of 10 years. The reset and interrupt vectors are located within the first 83 bytes of program
memory (refer to Table 9-1 on page 38). Constant tables can be allocated within the entire 64K
program memory address space for access by the MOVC instruction. A map of the
AT89LP51/52 program memory is shown in Figure 3-1.
11
3709D–MICRO–12/11
Figure 3-1.
Program Memory Map
01FF
AT89LP51
User Signature Array
User Signature Array
0100
0100
007F
0000
AT89LP52
01FF
Atmel Signature Array
007F
0000
SIGEN=1
Atmel Signature Array
FFFF
FFFF
External Program
Memory
(XCODE: 56KB)
External Program
Memory
(XCODE: 60KB)
SIGEN=0
1000
0FFF
0000
3.1.1
2000
1FFF
Internal Program
Memory
(CODE: 4KB)
Internal Program
Memory
(CODE: 8KB)
0000
External Program Memory Interface
The AT89LP51/52 uses the standard 8051 external program memory interface with the upper
address on Port 2, the lower address and data in/out multiplexed on Port 0, and the ALE and
PSEN strobes. Program memory addresses are always 16-bits wide, even though the actual
amount of program memory used may be less than 64K byes. External program execution sacrifices two full 8-bit ports, P0 and P2, to the function of addressing the program memory.
Figure 3-2 shows a hardware configuration for accessing up to 64K bytes of external ROM using
a 16-bit linear address. Port 0 serves as a multiplexed address/data bus to the ROM. The
Address Latch Enable strobe (ALE) is used to latch the lower address byte into an external register so that Port 0 can be freed for data input/output. Port 2 provides the upper address byte
throughout the operation. PSEN strobes the external memory.
Figure 3-3 shows the timing of the external program memory interface. ALE is emitted at a constant rate of 1/3 of the system clock with a 1/3 duty cycle. PSEN is emitted at a similar rate, but
with 50% duty cycle. The new address changes in the middle of the ALE pulse for latching on
the falling edge and is tristated at the falling edge of PSEN. The instruction data is sampled from
P0 and latched internally during the high phase of the clock prior to the rising edge of PSEN.
This timing applies to both Compatibility and Fast modes. In Compatibility mode there is no difference in instruction timing between internal and external execution.
Figure 3-2.
Executing from External Program Memory
AT89LP
P1
EXTERNAL
PROGRAM
MEMORY
INSTR.
P0
ALE
LATCH
P3
P2
PSEN
12
ADDR
OE
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 3-3.
External Program Memory Fetches
CLK
ALE
PSEN
DATA
SAMPLED
P0
P2
PCL
OUT
FLOAT
DATA
SAMPLED
DATA
SAMPLED
PCL
OUT
PCL
OUT
PCH OUT
PCH OUT
PCH OUT
In order for Fast mode to fetch externally, two wait states must be inserted for every clock cycle,
increasing the instruction execution time by a factor of 3. However, due to other optimizations,
external Fast mode instructions may still be 1/4 to 1/2 faster than their Compatibility mode equivalents. Note that if ALE is allowed to toggle in Fast mode, there is a possibility that when the
CPU jumps from internal to external execution a short pulse may occur on ALE as shown in Figure 3-4. The setup time from the address to the falling edge of ALE remains the same. However,
this behavior can be avoided by setting the DISALE bit prior to any jump above the 8K border.
Figure 3-4.
Internal/External Program Memory Boundary (Fast Mode)
CLK
SHORT
PULSE
ALE
DISALE=0
ALE
DISALE=1
INTERNAL EXECUTION
EXTERNAL EXECUTION
PSEN
DATA
SAMPLED
3.1.2
P0
P0 SFR OUT
P2
P2 SFR OUT
PCL OUT
FLOAT
PCH OUT
PCL OUT
PCH OUT
SIG
In addition to the 64K code space, the AT89LP51/52 also supports a 256-byte User Signature
Array and a 128-byte Atmel Signature Array that are accessible by the CPU. The Atmel Signature Array is initialized with the Device ID in the factory. The User Signature Array is available for
user identification codes or constant parameter data. Data stored in the signature array is not
secure. Security bits will disable writes to the array; however, reads by an external device programmer are always allowed.
In order to read from the signature arrays, the SIGEN bit (AUXR1.3) must be set (See Table 5-3
on page 28). While SIGEN is one, MOVC A,@A+DPTR will access the signature arrays. The
User Signature Array is mapped from addresses 0100h to 01FFh and the Atmel Signature Array
is mapped from addresses 0000h to 007Fh. SIGEN must be cleared before using MOVC to
13
3709D–MICRO–12/11
access the code memory. The User Signature Array may also be modified by the In-Application
Programming interface. When IAP = 1 and SIGEN = 1, MOVX @DPTR instructions will access
the array (See Section 3.4 on page 23).
3.2
Internal Data Memory
The AT89LP51/52 contains 256 bytes of general SRAM data memory plus 128 bytes of I/O
memory mapped into a single 8-bit address space. Access to the internal data memory does not
require any configuration. The internal data memory has three address spaces: DATA, IDATA
and SFR; as shown in Figure 3-5. Some portions of external data memory are also implemented
internally. See “External Data Memory” below for more information.
Figure 3-5.
Internal Data Memory Map
FFH
FFH
IDATA
ACCESSIBLE
BY INDIRECT
ADDRESSING
ONLY
UPPER
128
80H
7FH
0
3.2.1
80H
DATA/IDATA
ACCESSIBLE
BY DIRECT
AND INDIRECT
ADDRESSING
LOWER
128
SFR
ACCESSIBLE
BY DIRECT
ADDRESSING
SPECIAL
FUNCTION
REGISTERS
PORTS
STATUS AND
CONTROL BITS
TIMERS
REGISTERS
STACK POINTER
ACCUMULATOR
(ETC.)
DATA
The first 128 bytes of RAM are directly addressable by an 8-bit address (00H–7FH) included in
the instruction. The lowest 32 bytes of DATA memory are grouped into 4 banks of 8 registers
each. The RS0 and RS1 bits (PSW.3 and PSW.4) select which register bank is in use. Instructions using register addressing will only access the currently specified bank. The lower 128 bit
addresses are also mapped into DATA addresses 20H—2FH.
3.2.2
IDATA
The full 256 byte internal RAM can be indirectly addressed using the 8-bit pointers R0 and R1.
The first 128 bytes of IDATA include the DATA space. The hardware stack is also located in the
IDATA space.
3.2.3
SFR
The upper 128 direct addresses (80H–FFH) access the I/O registers. I/O registers on AT89LP
devices are referred to as Special Function Registers. The SFRs can only be accessed through
direct addressing. All SFR locations are not implemented. See Section 4. for a listed of available
SFRs.
3.3
External Data Memory
AT89LP microcontrollers support a 16-bit external memory address space for up to 64K bytes of
external data memory (XDATA). The external memory space is accessed with the MOVX
instructions. Some internal data memory resources are mapped into portions of the external
14
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
address space as shown in Figure 3-6. These memory spaces may require configuration before
the CPU can access them. The AT89LP51/52 includes 256 bytes of nonvolatile Flash data
memory (FDATA).
3.3.1
XDATA
The external data memory space can accommodate up to 64KB of external memory. The
AT89LP51/52 uses the standard 8051 external data memory interface with the upper address
byte on Port 2, the lower address byte and data in/out multiplexed on Port 0, and the ALE, RD
and WR strobes. XDATA can be accessed with both 16-bit (MOVX @DPTR) and 8-bit (MOVX
@Ri) addresses. See Section 3.3.3 on page 18 for more details of the external memory
interface.
Some internal data memory spaces are mapped into portions of the XDATA address space. In
this case the lower address ranges will access internal resources instead of external memory.
Addresses above the range implemented internally will default to XDATA. The AT89LP51/52
supports up to 63.75K or 56K bytes of external memory when using the internally mapped memories. Setting the EXRAM bit (AUXR.1) to one will force all MOVX instructions to access the
entire 64KB XDATA regardless of their address (See “AUXR – Auxiliary Control Register” on
page 20).
Figure 3-6.
External Data Memory Map
FFFF
FFFF
FFFF
External Data
(XDATA: 56KB)
External Data
(XDATA: 64KB)
External Data
(XDATA: 63.75KB)
0100
00FF
2000
1FFF
Flash Program
(CODE: 8KB)
Flash Data
(FDATA: 256)
0000
EXRAM = 1 or
DMEN = 0
IAP = 0
3.3.2
EXRAM = 0
DMEN = 1
IAP = 0
EXRAM = 0
DMEN = x
IAP = 1
FDATA
The Flash Data Memory is a portion of the external memory space implemented as an internal
nonvolatile data memory. Flash Data Memory is enabled by setting the DMEN bit (MEMCON.3)
to one. When IAP = 0 and DMEN = 1, the Flash Data Memory is mapped into the FDATA space,
at the bottom of the external memory address space, from 0000H to 00FFH. (See Figure 3-6).
MOVX instructions to this address range will access the internal nonvolatile memory. FDATA is
15
3709D–MICRO–12/11
not accessible while DMEN = 0. FDATA can be accessed only by 16-bit (MOVX @DPTR)
addresses. MOVX @Ri instructions to the FDATA address range will access external memory.
Addresses above the FDATA range are mapped to XDATA.
3.3.2.1
Write Protocol
The FDATA address space accesses an internal nonvolatile data memory. This address space
can be read just like EDATA by issuing a MOVX A,@DPTR; however, writes to FDATA require a
more complex protocol and take several milliseconds to complete.
For internal execution the AT89LP51/52 uses an idle-while-write architecture where the CPU is
placed in an idle state while the write occurs. When the write completes, the CPU will continue
executing with the instruction after the MOVX @DPTR,A instruction that started the write. All
peripherals will continue to function during the write cycle; however, interrupts will not be serviced until the write completes.
For external execution the AT89LP51/52 uses an execute-while-write architecture where the
CPU continues to operate while the write occurs. The software should poll the state of the BUSY
flag to determine when the write completes. Interrupts must be disabled during the write
sequence as the CPU will not be able to vector to the internal interrupt table and care should be
taken that the application does not jump to an internal address until the write completes.
To enable write access to the nonvolatile data memory, the MWEN bit (MEMCON.4) must be set
to one. When MWEN = 1 and DMEN = 1, MOVX @DPTR,A may be used to write to FDATA.
FDATA uses flash memory with a page-based programming model. Flash data memory differs
from traditional EEPROM data memory in the method of writing data. EEPROM generally can
update a single byte with any value. Flash memory splits programming into write and erase
operations. A Flash write can only program zeroes, i.e change ones into zeroes ( 1 →0 ). Any
ones in the write data are ignored. A Flash erase sets an entire page of data to ones so that all
bytes become FFH. Therefore after an erase, each byte in the page can only be written once
with any possible value. Bytes can be overwritten without an erase as long as only ones are
changed into zeroes. However, if even a single bit needs updating from zero to one ( 0 →1 );
then the contents of the page must first be saved, the entire page must be erased and the zero
bits in all bytes (old and new data combined) must be written. Avoiding unnecessary page
erases greatly improves the endurance of the memory..
The AT89LP51/52 includes 2 data pages of 128 bytes each. One or more bytes in a page may
be written at one time. The AT89LP51/52 includes a temporary page buffer of 64 bytes, or half of
a page. Because the page buffer is 64 bytes long, the maximum number of bytes written at one
time is 64. Therefore, two write cycles are required to fill the entire 128-byte page, one for the
low half page (00H–3FH) and one for the high half page (40H–7FH) as shown in Figure 3-7.
Figure 3-7.
Page Programming Structure
00
3F
Page Buffer
Data Memory
Low Half Page
00
16
High Half Page
3F 40
7F
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
The LDPG bit (MEMCON.5) allows multiple data bytes to be loaded to the temporary page buffer. While LDPG = 1, MOVX @DPTR,A instructions will load data to the page buffer, but will not
start a write sequence. Note that a previously loaded byte must not be reloaded prior to the write
sequence. To write the half page into the memory, LDPG must first be cleared and then a
MOVX @DPTR,A with the final data byte is issued. The address of the final MOVX determines
which half page will be written. If a MOVX @DPTR,A instruction is issued while LDPG = 0 without loading any previous bytes, only a single byte will be written. The page buffer is reset after
each write operation. Figures 3-8 and Figure 3-9 on page 17 show the difference between byte
writes and page writes.
Figure 3-8.
FDATA Byte Write
DMEN
MWEN
LDPG
IDLE
tWC
tWC
MOVX
Figure 3-9.
FDATA Page Write
DMEN
MWEN
LDPG
IDLE
tWC
MOVX
The auto-erase bit AERS (MEMCON.6) can be set to one to perform a page erase automatically
at the beginning of any write sequence. The page erase will erase the entire page, i.e. both the
low and high half pages. However, the write operation paired with the auto-erase can only program one of the half pages. A second write cycle without auto-erase is required to update the
other half page.
Frequently just a few bytes within a page must be updated while maintaining the state of the
other bytes. There are two options for handling this situation that allow the Flash Data memory
to emulate a traditional EEPROM memory. The simplest method is to copy the entire page into a
buffer allocated in RAM, modify the desired byte locations in the RAM buffer, and then load and
write back first the low half page (with auto-erase) and then the high half page to the Flash memory. This option requires that at least one page size of RAM is available as a temporary buffer.
The second option is to store only one half page in RAM. The unmodified bytes of the other page
are loaded directly into the Flash memory’s temporary load buffer before loading the updated
values of the modified bytes. For example, if just the low half page needs modification, the user
must first store the high half page to RAM, followed by reading and loading the unaffected bytes
of the low half page into the page buffer. Then the modified bytes of the low half page are stored
17
3709D–MICRO–12/11
to the page buffer before starting the auto-erase sequence. The stored value of the high half
page must be written without auto-erase after the programming of the low half page completes.
This method reduces the amount of RAM required; however, more software overhead is needed
because the read-and-load-back routine must skip those bytes in the page that need to be
updated in order to prevent those locations in the buffer from being loaded with the previous
data, as this will block the new data from being loaded correctly.
A write sequence will not occur if the Brown-out Detector is active. If a write currently in progress
is interrupted by the BOD due to a low voltage condition, the ERR flag will be set.
Table 3-2.
MEMCON – Memory Control Register
MEMCON = 96H
Reset Value = 0000 0XXXB
Not Bit Addressable
Bit
IAP
AERS
LDPG
MWEN
DMEN
ERR
BUSY
WRTINH
7
6
5
4
3
2
1
0
Symbol
Function
IAP
In-Application Programming Enable. When IAP = 1 and the IAP Fuse is enabled, programming of the CODE/SIG space
is enabled and MOVX @DPTR instructions will access CODE/SIG instead of EDATA or FDATA. Clear IAP to disable
programming of CODE/SIG and allow access to EDATA and FDATA.
AERS
Auto-Erase Enable. Set to perform an auto-erase of a Flash memory page (CODE, SIG or FDATA) during the next write
sequence. Clear to perform write without erase.
LDPG
Load Page Enable. Set to this bit to load multiple bytes to the temporary page buffer. Byte locations may not be loaded
more than once before a write. LDPG must be cleared before writing.
MWEN
Memory Write Enable. Set to enable programming of a nonvolatile memory location (CODE, SIG or FDATA). Clear to
disable programming of all nonvolatile memories.
DMEN
Data Memory Enable. Set to enable nonvolatile data memory and map it into the FDATA space. Clear to disable
nonvolatile data memory.
ERR
Error Flag. Set by hardware if an error occurred during the last programming sequence due to a brownout condition (low
voltage on VDD). Must be cleared by software.
BUSY
Busy Flag.
WRTINH
Write Inhibit Flag. Cleared by hardware when the voltage on VDD has fallen below the minimum programming voltage.
Set by hardware when the voltage on VDD is above the minimum programming voltage.
3.3.3
External Data Memory Interface
The AT89LP51/52 uses the standard 8051 external data memory interface with the upper
address on Port 2, the lower address and data in/out multiplexed on Port 0, and the ALE, RD
and WR strobes. The interface may be used in two different configurations depending on which
type of MOVX instruction is used to access XDATA.
Figure 3-10 shows a hardware configuration for accessing up to 64K bytes of external RAM
using a 16-bit linear address. Port 0 serves as a multiplexed address/data bus to the RAM. The
Address Latch Enable strobe (ALE) is used to latch the lower address byte into an external register so that Port 0 can be freed for data input/output. Port 2 provides the upper address byte
throughout the operation. The MOVX @DPTR instructions use Linear Address mode.
18
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 3-10. External Data Memory 16-bit Linear Address Mode
EXTERNAL
DATA
MEMORY
DATA
AT89LP
P0
P1
ALE
LATCH
ADDR
P2
RD
WR
P3
WE
OE
Figure 3-11 shows a hardware configuration for accessing 256-byte blocks of external RAM
using an 8-bit paged address. Port 0 serves as a multiplexed address/data bus to the RAM. The
ALE strobe is used to latch the address byte into an external register so that Port 0 can be freed
for data input/output. The Port 2 I/O lines (or other ports) can provide control lines to page the
memory; however, this operation is not handled automatically by hardware. The software application must change the Port 2 register when appropriate to access different pages. The
MOVX @Ri instructions use Paged Address mode.
Figure 3-11. External Data Memory 8-bit Paged Address Mode
EXTERNAL
DATA
MEMORY
DATA
AT89LP
P1
P0
ALE
RD
WR
LATCH
ADDR
PAGE
BITS
WE
P3 P2
I/O
OE
Note that prior to using the external memory interface, WR (P3.6) and RD (P3.7) must be configured as outputs. See Section 10.1 “Port Configuration” on page 41. P0 and P2 are configured
automatically to push-pull output mode when outputting address or data and P0 is automatically
tristated when inputting data regardless of the port configuration. The Port 0 configuration will
determine the idle state of Port 0 when not accessing the external memory.
Figure 3-12 and Figure 3-13 show examples of external data memory write and read cycles,
respectively. The address on P0 and P2 is stable at the falling edge of ALE. The idle state of
ALE is controlled by DISALE (AUXR.0). When DISALE = 0 the ALE toggles at a constant rate
when not accessing external memory. When DISALE = 1 the ALE is weakly pulled high. DISALE
must be one in order to use P4.4 as a general-purpose I/O. The WS bits in AUXR can extended
the RD and WR strobes by 1, 2 or 3 cycles as shown in Figures 3-16, 3-17 and 3-18. If a longer
strobe is required, the application can scale the system clock with the clock divider to meet the
requirements (See Section 6.4 on page 31).
19
3709D–MICRO–12/11
Table 3-3.
AUXR – Auxiliary Control Register
AUXR = 8EH
Reset Value = xxx0 0000B
Not Bit Addressable
Bit
Symbol
–
–
–
WDIDLE(1)
DISRTO(1)
WS1(2)
WS0
EXRAM
DISALE
7
6
5
4
3
2
1
0
Function
WDIDLE
WDT Disable during Idle(1). When WDIDLE = 0 the WDT continues to count in Idle mode. When WDIDLE = 1 the WDT
halts counting in Idle mode.
DISRTO
Disable Reset Output(1). When DISTRO = 0 the reset pin is driven to the same level as POL when the WDT resets.
When DISRTO = 1 the reset pin is input only.
WS[1-0]
Wait State Select. Determines the number of wait states inserted into external memory accesses.
WS1(2)
WS0
Wait States
RD / WR Strobe Width
ALE to RD / WR Setup
0
0
0
1 x tCYC (Fast); 3 x tCYC (Compatibility)
1 x tCYC (Fast); 1.5 x tCYC (Compatibility)
0
1
1
2 x tCYC (Fast); 15 x tCYC (Compatibility)
1 x tCYC (Fast); 1.5 x tCYC (Compatibility)
1
0
2
2 x tCYC (Fast)
2 x tCYC (Fast)
1
1
3
3 x tCYC (Fast)
2 x tCYC (Fast)
EXRAM
External RAM Enable. When EXRAM = 0, MOVX instructions can access the internally mapped portions of the address
space. Accesses to addresses above internally mapped memory will access external memory. Set EXRAM = 1 to
bypass the internal memory and map the entire address space to external memory.
DISALE
ALE Disable. When DISALE = 0 the ALE pulse is active at 1/3 of the system clock frequency in Compatibility mode and
1/2 of the system clock frequency in Fast mode. When DISALES = 1 the ALE is inactive (high) unless an external
memory access occurs. DISALE must be set to use P4.4 as a general I/O.
Notes:
1. AUXR.4 and AUXR.3 function as WDIDLE and DISRTO only in Compatibility mode. In Fast mode these bits are located in
WDTCON.
2. WS1 is only available in Fast mode. WS1 is forced to 0 in Compatibility mode.
Figure 3-12. Fast Mode External Data Memory Write Cycle (WS = 00B)
S1
S2
P0
P0 SFR
DPL or Ri OUT
P2
P2 SFR
S3
S4
CLK
ALE
WR
20
DATA OUT
DPH or P2 OUT
P0 SFR
P2 SFR
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 3-13. Fast Mode External Data Memory Read Cycle (WS = 00B)
S1
S2
S3
P0
P0 SFR
DPL or Ri OUT
P2
P2 SFR
S4
CLK
ALE
RD
DATA SAMPLED
P0 SFR
FLOAT
DPH or P2 OUT
P2 SFR
Figure 3-14. Compatibility Mode External Data Memory Write Cycle (WS0 = 0)
S4
S5
S6
S1
S2
S3
S4
S5
CLK
ALE
WR
P0
P0 SFR
P2
PCH or
P2 SFR
DPL or Ri
OUT
PCL or
P0 SFR
DATA OUT
PCH or
P2 SFR
DPH or P2 OUT
Figure 3-15. Compatibility Mode External Data Memory Read Cycle (WS0 = 0)
S4
S5
S6
S1
S2
S3
S4
S5
CLK
ALE
RD
DATA SAMPLED
P0
P0 SFR
P2
PCH or
P2 SFR
DPL or Ri
OUT
FLOAT
DPH or P2 OUT
PCL or
P0 SFR
PCH or
P2 SFR
21
3709D–MICRO–12/11
Figure 3-16. MOVX with One Wait State (WS = 01B)
S1
S2
S3
W1
S4
CLK
ALE
P2
P2 SFR
DPH or P2 OUT
P2 SFR
WR
P0
P0 SFR
DPL OUT
P0 SFR
DPL OUT
DATA OUT
P0 SFR
RD
P0
FLOAT
P0 SFR
Figure 3-17. MOVX with Two Wait States (WS = 10B)
S1
S2
S3
W1
W2
S4
CLK
ALE
P2
P2 SFR
DPH or P2 OUT
P2 SFR
WR
P0
P0 SFR
DPL OUT
P0 SFR
DPL OUT
DATA OUT
P0 SFR
RD
P0
FLOAT
P0 SFR
Figure 3-18. MOVX with Three Wait States (WS = 11B)
S1
S2
S3
W1
W2
W3
S4
CLK
ALE
P2
P2 SFR
DPH or P2 OUT
P2 SFR
WR
P0
P0 SFR
DPL OUT
P0 SFR
DPL OUT
DATA OUT
P0 SFR
RD
P0
22
FLOAT
P0 SFR
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
3.4
In-Application Programming (IAP)
The AT89LP51/52 supports In-Application Programming (IAP), allowing the program memory to
be modified during execution. IAP can be used to modify the user application on the fly or to use
program memory for nonvolatile data storage. The same page structure write protocol for
FDATA also applies to IAP (See Section 3.3.2.1 “Write Protocol” on page 16). The CPU is
always placed in idle while modifying the program memory. When the write completes, the CPU
will continue executing with the instruction after the MOVX @DPTR,A instruction that started the
write.
To enable access to the program memory, the IAP bit (MEMCON.7) must be set to one and the
IAP User Fuse must be enabled. The IAP User Fuse can disable all IAP operations. When this
fuse is disabled, the IAP bit will be forced to 0. While IAP is enabled, all MOVX @DPTR instructions will access the CODE space instead of EDATA/FDATA/XDATA. IAP also allows
reprogramming of the User Signature Array when SIGEN = 1. The IAP access settings are summarized in Table 3-4 and Table 3-5.
Table 3-4.
IAP Access Settings for AT89LP52
IAP
SIGEN
DMEN
MOVX @DPTR
MOVC @DPTR
0
0
0
XDATA (0000–FFFFH)
CODE (0000–1FFFH)
XCODE (2000–FFFFH)
0
0
1
FDATA (0000–00FFH)
XDATA (0100–FFFFH)
CODE (0000–1FFFH)
XCODE (2000–FFFFH)
0
1
0
XDATA (0000–FFFFH)
SIG (0000–01FFH)
0
1
1
FDATA (0000–00FFH)
XDATA (0100–FFFFH)
SIG (0000–01FFH)
1
0
X
CODE (0000–1FFFH)
XDATA (2000–FFFFH)
CODE (0000–1FFFH)
XCODE (2000–FFFFH)
1
1
X
SIG (0000–01FFH)
XDATA (2000–FFFFH)
SIG (0000–01FFH)
Table 3-5.
IAP Access Settings for AT89LP51
IAP
SIGEN
DMEN
MOVX @DPTR
MOVC @DPTR
0
0
0
XDATA (0000–FFFFH)
CODE (0000–0FFFH)
XCODE (1000–FFFFH)
0
0
1
FDATA (0000–00FFH)
XDATA (0100–FFFFH)
CODE (0000–0FFFH)
XCODE (1000–FFFFH)
0
1
0
XDATA (0000–FFFFH)
SIG (0000–01FFH)
0
1
1
FDATA (0000–00FFH)
XDATA (0100–FFFFH)
SIG (0000–01FFH)
1
0
X
CODE (0000–0FFFH)
XDATA (1000–FFFFH)
CODE (0000–0FFFH)
XCODE (1000–FFFFH)
1
1
X
SIG (0000–01FFH)
XDATA (1000–FFFFH)
SIG (0000–01FFH)
Note:
When In-Application programming is not required, it is recommended that the IAP User Fuse be
disabled.
23
3709D–MICRO–12/11
4. Special Function Registers
A map of the on-chip memory area called the Special Function Register (SFR) space is shown in
Table 4-1.
Note that not all of the addresses are occupied, and unoccupied addresses may not be implemented on the chip. Read accesses to these addresses will in general return random data, and
write accesses will have an indeterminate effect. User software should not write to these unlisted
locations, since they may be used in future products to invoke new features.
Table 4-1.
AT89LP51/52 SFR Map and Reset Values
8
9
A
B
C
D
E
F
0F8H
0F0H
0FFH
B
0000 0000
0F7H
0E8H
0E0H
0EFH
ACC
0000 0000
0E7H
0D8H
0D0H
0C8H
0DFH
PSW
0000 0000
0D7H
T2CON
0000 0000
T2MOD
0000 0000
0C0H
P4
1111 1111
PMOD
(2)
0C7H
0B8H
IP
xx00 0000
SADEN
0000 0000
0BFH
0B0H
P3
1111 1111
0A8H
IE
0x00 0000
0A0H
RCAP2L
0000 000
RCAP2H
0000 0000
TL2
0000 000
TH2
0000 0000
IPH
xx00 0000
SADDR
0000 0000
P2
1111 1111
0B7H
0AFH
AUXR1
0000 00x0
WDTRST
(write-only)
98H
SCON
0000 0000
SBUF
xxxx xxxx
90H
P1
1111 1111
TCONB
000x xxxx
88H
TCON
0000 0000
TMOD
0000 0000
TL0
0000 0000
TL1
0000 0000
TH0
0000 0000
TH1
0000 0000
80H
P0
1111 1111
SP
0000 0111
DP0L
0000 0000
DP0H
0000 0000
DP1L
0000 0000
DP1H
0000 0000
0
1
2
3
4
5
Notes:
0CFH
WDTCON
0000 0xx0
0A7H
9FH
MEMCON
0000 00xx
AUXR
0000 0000
6
97H
CLKREG
(3)
8FH
PCON
000x 0000
87H
7
1. All SFRs in the left-most column are bit-addressable.
2. Reset value is 0101 0101B when Tristate-Port Fuse is enabled and 0000 0011B when disabled.
3. Reset value is 0101 0010B when Compatibility mode is enabled and 0000 0000B when disabled.
24
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
5. Enhanced CPU
The AT89LP51/52 uses an enhanced 8051 CPU that runs at 6 to 12 times the speed of standard
8051 devices (or 3 to 6 times the speed of X2 8051 devices). The increase in performance is
due to two factors. First, the CPU fetches one instruction byte from the code memory every clock
cycle. Second, the CPU uses a simple two-stage pipeline to fetch and execute instructions in
parallel. This basic pipelining concept allows the CPU to obtain up to 1 MIPS per MHz. The
AT89LP51/52 also has a Compatibility mode that preserves the 12-clock machine cycle of standard 8051s like the AT89S51/52.
5.1
Fast Mode
Fast (Single-Cycle) mode must be enabled by clearing the Compatibility User Fuse. (See “User
Configuration Fuses” on page 86.) In this mode one instruction byte is fetched every system
clock cycle. The 8051 instruction set allows for instructions of variable length from 1 to 3 bytes.
In a single-clock-per-byte-fetch system this means each instruction takes at least as many
clocks as it has bytes to execute. The majority of instructions in the AT89LP51/52 follow this
rule: the instruction execution time in system clock cycles equals the number of bytes per
instruction, with a few exceptions. Branches and Calls require an additional cycle to compute the
target address and some other complex instructions require multiple cycles. See “Instruction Set
Summary” on page 75. for more detailed information on individual instructions.
Example of Fast mode instructions are shown in Figure 5-1. Note that Fast mode instructions
take three times as long to execute if they are fetched from external program memory.
Figure 5-1.
Instruction Execution Sequences in Fast Mode
CLK
READ NEXT
OPCODE
S1
(A) 1-byte, 1-cycle instruction, e.g. INC A
READ OPERAND
READ NEXT OPCODE
S1
S2
(B) 2-byte, 2-cycle instruction, e.g. ADD A, #data
READ NEXT OPCODE
S1
S2
(C) 1-byte, 2-cycle instruction, e.g. INC DPTR
READ NEXT
OPCODE
S1
S2
ADDR
S3
S4
DATA
ACCESS EXTERNAL
MEMORY
(D) MOVX (1-byte, 4-cycle)
25
3709D–MICRO–12/11
5.2
Compatibility Mode
Compatibility (12-Clock) mode is enabled by default from the factory or by setting the Compatibility User Fuse. In Compatibility mode instruction bytes are fetched every three system clock
cycles and the CPU operates with 6-state machine cycles and a divide-by-2 system clock for 12
oscillator periods per machine cycle. Standard instructions execute in1, 2 or 4 machine cycles.
Instruction timing in this mode is compatible with standard 8051s such as the AT89S51/52.
Compatibility mode can be used to preserve the execution profiles of legacy applications. For a
summary of differences between Fast and Compatibility modes see Table 2-3 on page 10.
Examples of Compatibility mode instructions are shown in Figure 5-2.
Figure 5-2.
Instruction Execution Sequences in Compatibility Mode
S1
S2
S3
S4
S5
S6
S1
S2
S3
S4
S5
S6
S1
CLK
ALE
READ OPCODE
S1
S2
S3
S4
READ NEXT
OPCODE
(DISCARD)
S5
READ NEXT OPCODE AGAIN
S6
(A) 1-byte, 1-cycle instruction, e.g., INC A
READ OPCODE
READ 2ND
BYTE
S1
S2
S3
S4
S5
(B) 2-byte, 1-cycle instruction, e.g., ADD A, #data
S2
S3
S4
S6
READ NEXT
OPCODE (DISCARD)
READ OPCODE
S1
READ NEXT OPCODE
S5
S6
S1
S2
READ NEXT
OPCODE AGAIN
S3
S4
S5
S6
(C) 1-byte, 2-cycle instruction, e.g., INC DPTR
READ
OPCODE
(MOVX)
S1
(D) MOVX (1-byte, 2-cycle)
S2
S3
NO
READ NEXT
OPCODE (DISCARD) FETCH
S4
S5
ADDR
S6
S1
NO READ NEXT
FETCH
OPCODE
AGAIN
NO
ALE
S2
S3
S4
S5
S6
DATA
DA
MEMORY
ACCESS EXTERNAL MEMOR
5.3
Enhanced Dual Data Pointers
The AT89LP51/52 provides two 16-bit data pointers: DPTR0 formed by the register pair DPOL
and DPOH (82H an 83H), and DPTR1 formed by the register pair DP1L and DP1H (84H and
85H). The data pointers are used by several instructions to access the program or data memories. The Data Pointer Configuration Register (AUXR1) controls operation of the dual data
pointers (Table 5-3 on page 28). The DPS bit in AUXR1 selects which data pointer is currently
referenced by instructions including the DPTR operand. Each data pointer may be accessed at
its respective SFR addresses regardless of the DPS value. The AT89LP51/52 provides two
methods for fast context switching of the data pointers:
26
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
• Bit 2 of AUXR1 is hard-wired as a logic 0. The DPS bit may be toggled (to switch data
pointers) simply by incrementing the AUXR1 register, without altering other bits in the register
unintentionally. This is the preferred method when only a single data pointer will be used at
one time.
EX:
INC
AUXR1
; Toggle DPS
• In some cases, both data pointers must be used simultaneously. To prevent frequent toggling
of DPS, the AT89LP51/52 supports a prefix notation for selecting the opposite data pointer
per instruction. All DPTR instructions, with the exception of JMP @A+DPTR, when prefixed
with an 0A5H opcode will use the inverse value of DPS (DPS) to select the data pointer.
Some assemblers may support this operation by using the /DPTR operand. For example, the
following code performs a block copy within EDATA:
COPY:
MOV
AUXR1, #00H
; DPS = 0
MOV
DPTR, #SRC
; load source address to dptr0
MOV
/DPTR, #DST
; load destination address to dptr1
MOV
R7, #BLKSIZE
; number of bytes to copy
MOVX A, @DPTR
; read source (dptr0)
INC
; next src (dptr0+1)
DPTR
MOVX @/DPTR, A
; write destination (dptr1)
INC
; next dst (dptr1+1)
/DPTR
DJNZ R7, COPY
For assemblers that do not support this notation, the 0A5H prefix must be declared in-line:
EX:
DB
0A5H
INC
DPTR
; equivalent to INC /DPTR
A summary of data pointer instructions with fast context switching is listed inTable 5-1.
Table 5-1.
Data Pointer Instructions
Operation
5.3.1
Instruction
DPS = 0
DPS = 1
JMP @A+DPTR
JMP @A+DPTR0
JMP @A+DPTR1
MOV DPTR, #data16
MOV DPTR0, #data16
MOV DPTR1, #data16
MOV /DPTR, #data16
MOV DPTR1, #data16
MOV DPTR0, #data16
INC DPTR
INC DPTR0
INC DPTR1
INC /DPTR
INC DPTR1
INC DPTR0
MOVC A,@A+DPTR
MOVC A,@A+DPTR0
MOVC A,@A+DPTR1
MOVC A,@A+/DPTR
MOVC A,@A+DPTR1
MOVC A,@A+DPTR0
MOVX A,@DPTR
MOVX A,@DPTR0
MOVX A,@DPTR1
MOVX A,@/DPTR
MOVX A,@DPTR1
MOVX A,@DPTR0
MOVX @DPTR, A
MOVX @DPTR0, A
MOVX @DPTR1, A
MOVX @/DPTR, A
MOVX @DPTR1, A
MOVX @DPTR0, A
Data Pointer Update
The Dual Data Pointers on the AT89LP51/52 include two features that control how the data
pointers are updated. The data pointer decrement bits, DPD1 and DPD0 in AUXR1, configure
the INC DPTR instruction to act as DEC DPTR. The resulting operation will depend on DPS as
shown in Table 5-2. These bits also control the direction of auto-updates during MOVC and
MOVX.
27
3709D–MICRO–12/11
Table 5-2.
Data Pointer Decrement Behavior
Equivalent Operation for INC DPTR and INC /DPTR
DPS = 0
Table 5-3.
DPS = 1
DPD1
DPD0
INC DPTR
INC /DPTR
INC DPTR
INC /DPTR
0
0
INC DPTR0
INC DPTR1
INC DPTR1
INC DPTR0
0
1
DEC DPTR0
INC DPTR1
INC DPTR1
DEC DPTR0
1
0
INC DPTR0
DEC DPTR1
DEC DPTR1
INC DPTR0
1
1
DEC DPTR0
DEC DPTR1
DEC DPTR1
DEC DPTR0
AUXR1 – Data Pointer Configuration Register
AUXR1 = A2H
Reset Value = 0000 00X0B
Not Bit Addressable
Bit
DPU1
DPU0
DPD1
DPD0
SIGEN
0
–
DPS
7
6
5
4
3
2
1
0
Symbol
Function
DPU1
Data Pointer 1 Update. When set, MOVX @DPTR and MOVC @DPTR instructions that use DPTR1 will also update
DPTR1 based on DPD1. If DPD1 = 0 the operation is post-increment and if DPD1 = 1 the operation is post-decrement.
When DPU1 = 0, DPTR1 is not updated.
DPU0
Data Pointer 0 Update. When set, MOVX @DPTR and MOVC @DPTR instructions that use DPTR0 will also update
DPTR0 based on DPD0. If DPD0 = 0 the operation is post-increment and if DPD0 = 1 the operation is post-decrement.
When DPU0 = 0, DPTR0 is not updated.
DPD1
Data Pointer 1 Decrement. When set, INC DPTR instructions targeted to DPTR1 will decrement DPTR1. When cleared,
INC DPTR instructions will increment DPTR1. DPD1 also determines the direction of auto-update for DPTR1 when
DPU1 = 1.
DPD0
Data Pointer 0 Decrement. When set, INC DPTR instructions targeted to DPTR0 will decrement DPTR0. When cleared,
INC DPTR instructions will increment DPTR0. DPD0 also determines the direction of auto-update for DPTR0 when
DPU0 = 1.
SIGEN
Signature Enable. When SIGEN = 1 all MOVC @DPTR instructions and all IAP accesses will target the signature array
memory. When SIGEN = 0, all MOVC and IAP accesses target CODE memory.
DPS
Data Pointer Select. DPS selects the active data pointer for instructions that reference DPTR. When DPS = 0, DPTR will
target DPTR0 and /DPTR will target DPTR1. When DPS = 1, DPTR will target DPTR1 and /DPTR will target DPTR0.
The data pointer update bits, DPU1 and DPU0, allow MOVX @DPTR and MOVC @DPTR
instructions to update the selected data pointer automatically in a post-increment or post-decrement fashion. The direction of update depends on the DPD1 and DPD0 bits as shown in Table
5-4. These bits can be used to make block copy routines more efficient.
Table 5-4.
Data Pointer Auto-Update
Update Operation for MOVX and MOVC (DPU1 = 1 & DPU0 = 1)
DPS = 0
28
DPS = 1
DPD1
DPD0
DPTR
/DPTR
DPTR
/DPTR
0
0
DPTR0++
DPTR1++
DPTR1++
DPTR0++
0
1
DPTR0--
DPTR1++
DPTR1++
DPTR0--
1
0
DPTR0++
DPTR1--
DPTR1--
DPTR0++
1
1
DPTR0--
DPTR1--
DPTR1--
DPTR0--
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
6. System Clock
The system clock is generated directly from one of three selectable clock sources. The three
sources are the on-chip crystal oscillator, external clock source, and internal RC oscillator. A diagram of the clock subsystem is shown in Figure 6-1. The on-chip crystal oscillator may also be
configured for low or high power operation. The clock source is selected by the Clock Source
User Fuses as shown in Table 6-1. See “User Configuration Fuses” on page 86. By default, in
Fast mode no internal clock division is used to generate the CPU clock from the system clock. In
Compatibility mode the default is to divide the oscillator output by two. The system clock divider
may be used to prescale the system clock with other values. The choice of clock source also
affects the start-up time after a POR, BOD or Power-down event (See “Reset” on page 32 or
“Power-down Mode” on page 35)
Figure 6-1.
Clock Subsystem Diagram
CLOCK FUSES
INTERNAL
1.8432MHz
OSC
CLKIRC
0
CLKEXT
1
CLKXTAL
2
5-BIT
CLOCK
DIVIDER
CLKosc/32
CLKosc/8
CLKosc/16
CLKosc
CLKosc/2
CLKosc/4
3
XTAL1
TPS3-0
XTAL2
CDV2-0
0
1 2 3 4 5
4-BIT
PRESCALER
Timer 0
Timer 1
Timer 2
Watchdog
SYSTEM CLOCK
(CLKSYS)
Table 6-1.
6.1
Clock Source Settings
Clock Source
Fuse 1
Clock Source
Fuse 0
1
1
High Power Crystal Oscillator (f > 12 MHz)
1
0
Low Power Crystal Oscillator (f ≤12 MHz)
0
1
External Clock on XTAL1
0
0
Internal 1.8432 MHz Auxiliary Oscillator
Selected Clock Source
Crystal Oscillator
When enabled, the internal inverting oscillator amplifier is connected between XTAL1 and
XTAL2 for connection to an external quartz crystal or ceramic resonator. The oscillator may
operate in either high-power or low-power mode. Low-speed mode is intended for crystals of 12
MHz or less and consumes less power than the higher speed mode. The configuration as shown
in Figure 6-2 applies for both high and low power oscillators. Note that in some cases, external
capacitors C1 and C2 may NOT be required due to the on-chip capacitance of the XTAL1 and
XTAL2 inputs (approximately 10 pF each). When using the crystal oscillator, P4.6 and P4.7 will
have their inputs and outputs disabled. Also, XTAL2 in crystal oscillator mode should not be
used to directly drive a board-level clock without a buffer.
29
3709D–MICRO–12/11
An optional 5 MΩ on-chip resistor can be connected between XTAL1 and GND. This resistor can
improve the startup characteristics of the oscillator especially at higher frequencies. The resistor
can be enabled/disabled with the R1 User Fuse (See “User Configuration Fuses” on page 86.)
Figure 6-2.
Crystal Oscillator Connections
C2
~10 pF
C1
R1
~10 pF
Note:
6.2
1.
~5 MΩ
C1, C2 = 5 pF ± 5pF for Crystals
= 5 pF ± 5pF for Ceramic Resonators
External Clock Source
The external clock option disables the oscillator amplifier and allows XTAL1 to be driven directly
by an external clock source as shown in Figure 6-3. XTAL2 may be left unconnected, used as
general purpose I/O P4.7, or configured to output a divided version of the system clock.
Figure 6-3.
External Clock Drive Configuration
NC GPIO
XTAL2 (P4.7)
EXTERNAL
OSCILLATOR
SIGNAL
XTAL1 (P4.6)
GND
6.3
Internal RC Oscillator
The AT89LP51/52 has an Internal Auxiliary oscillator tuned to 1.8432 MHz ±2.0%. When
enabled as the clock source, XTAL1 and XTAL2 may be used as P4.6 and P4.7 respectively.
30
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
6.4
System Clock Divider
The CDV2-0 bits in CLKREG allow the system clock to be divided down from the selected clock
source by powers of 2. The clock divider provides users with a greater frequency range when
using the Internal Oscillator. For example, to achieve a 230.4 kHz system frequency when using
the RC oscillator, CDV2-0 should be set to 011B for divide-by-8 operation. The divider can also
be used to reduce power consumption by decreasing the operational frequency during non-critical periods. The resulting system frequency is given by the following equation:
f OSC
f SYS = -----------CDV
2
where fOSC is the frequency of the selected clock source. The clock divider will prescale the clock
for the CPU and all peripherals. The value of CDV may be changed at any time without interrupting normal execution. Changes to CDV are synchronized such that the system clock will not
pass through intermediate frequencies. When CDV is updated, the new frequency will take
affect within a maximum period of 32 x tOSC.
In Compatibility mode the divider defaults to divide-by-2 and and in Fast mode it defaults to no
division.
Table 6-2.
CLKREG – Clock Control Register
CLKREG = 8FH
Reset Value = 0?0? 00?0B
Not Bit Addressable
Bit
Symbol
TPS[3-0]
TPS3
TPS2
TPS1
TPS0
CDV2
CDV1
CDV0
—
7
6
5
4
3
2
1
0
Function
Timer Prescaler. The Timer Prescaler selects the time base for Timer 0, Timer 1, Timer 2 and the Watchdog Timer. The
prescaler is implemented as a 4-bit binary down counter. When the counter reaches zero it is reloaded with the value
stored in the TPS bits to give a division ratio between 1 and 16. By default the timers will count every clock cycle in Fast
mode (TPS = 0000B) and every six cycles in Compatibility mode (TPS = 0101B).
System Clock Division. Determines the frequency of the system clock relative to the oscillator clock source.
CDIV2
CDIV1
CDIV0
System Clock Frequency
0
0
0
fOSC/1
0
0
1
fOSC/2
0
1
0
fOSC/4
0
1
1
fOSC/8
1
0
0
fOSC/16
1
0
1
fOSC/32
1
1
0
Reserved
1
1
1
Reserved
CDV[2-0]
Note:
The reset value of CLKREG is 0000000B in Fast mode and 01010010B in Compatibility mode.
31
3709D–MICRO–12/11
7. Reset
During reset, all I/O Registers are set to their initial values, the port pins are set to their default
mode, and the program starts execution from the Reset Vector, 0000H. The AT89LP51/52 has
five sources of reset: power-on reset, brown-out reset, external reset, watchdog reset, and software reset.
7.1
Power-on Reset
A Power-on Reset (POR) is generated by an on-chip detection circuit. The detection level VPOR
is nominally 1.4V. The POR is activated whenever VDD is below the detection level. The POR circuit can be used to trigger the start-up reset or to detect a major supply voltage failure. The POR
circuit ensures that the device is reset from power-on. A power-on sequence is shown in Figure
7-1. When VDD reaches the Power-on Reset threshold voltage VPOR, an initialization sequence
lasting tPOR is started. When the initialization sequence completes, the start-up timer determines
how long the device is kept in POR after VDD rise. The start-up timer does not begin counting
until after VDD reaches the Brown-out Detector (BOD) threshold voltage VBOD. The POR signal is
activated again, without any delay, when VDD falls below the POR threshold level. A Power-on
Reset (i.e. a cold reset) will set the POF flag in PCON. The internally generated reset can be
extended beyond the power-on period by holding the RST pin active longer than the time-out.
Figure 7-1.
Power-on Reset Sequence
VBOD
VDD
Time-out
VPOR
tSUT
tPOR
POL
(POL Tied to VCC)
RST
(RST Tied to GND)
Internal
Reset
RST
(RST Controlled Externally)
Internal
Reset
Note:
VIL
tRHD
tPOR is approximately 143 µs ± 5%.
The start-up timer delay is user-configurable with the Start-up Time User Fuses and depends on
the clock source (Table 7-1). The Start-Up Time fuses also control the length of the start-up time
after a Brown-out Reset or when waking up from Power-down during internally timed mode. The
start-up delay should be selected to provide enough settling time for VDD and the selected clock
source. The device operating environment (supply voltage, frequency, temperature, etc.) must
meet the minimum system requirements before the device exits reset and starts normal operation. The RST pin may be held active externally until these conditions are met.
32
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Table 7-1.
Start-up Timer Settings
SUT Fuse 1
SUT Fuse 0
0
0
Clock Source
tSUT (± 5%) µs
Internal RC/External Clock
0
Crystal Oscillator
1024
Internal RC/External Clock
512
Crystal Oscillator
2048
Internal RC/External Clock
1024
Crystal Oscillator
4096
Internal RC/External Clock
4096
Crystal Oscillator
16384
1
1
0
1
7.2
16
1
Brown-out Reset
The AT89LP51/52 has an on-chip Brown-out Detection (BOD) circuit for monitoring the VDD level
during operation by comparing it to a fixed trigger level. The trigger level VBOD for the BOD is
nominally 2.0V. The purpose of the BOD is to ensure that if VDD fails or dips while executing at
speed, the system will gracefully enter reset without the possibility of errors induced by incorrect
execution. A BOD sequence is shown in Figure 7-2. When VDD decreases to a value below the
trigger level VBOD, the internal reset is immediately activated. When VDD increases above the
trigger level plus about 200 mV of hysteresis, the start-up timer releases the internal reset after
the specified time-out period has expired (Table 7-1).
Figure 7-2.
VDD
Time-out
Brown-out Detector Reset
VPOR
VBOD
tSUT
Internal
Reset
The AT89LP51/52 allows for a wide VDD operating range. The on-chip BOD may not be sufficient to prevent incorrect execution if VBOD is lower than the minimum required VDD range, such
as when a 5.0V supply is coupled with high frequency operation. In such cases an external
Brown-out Reset circuit connected to the RST pin may be required.
7.3
External Reset
The RST pin of the AT89LP51/52 can function as either an active-low reset input or as an activehigh reset input. The polarity of the RST pin is selectable using the POL pin (formerly EA). When
POL is high the RST pin is active high with an on-chip pull-down resistor tied to GND. When
POL is low the RST pin is active low with an on-chip pull-up resistor tied to VDD. The RST pin
structure is shown in Figure 7-3. In Compatibility mode the reset pin is sampled every six clock
cycles and must be held active for at least twelve clock cycles to trigger the internal reset. In
Fast mode the reset pin is sampled every clock cycle and must be held active for at least two
clock cycles to trigger the internal reset.
33
3709D–MICRO–12/11
The AT89LP51/52 includes an on-chip Power-On Reset and Brown-out Detector circuit that
ensures that the device is reset from system power up. In most cases a RC startup circuit is not
required on the RST pin, reducing system cost, and the RST pin may be left unconnected if a
board-level reset is not present.
Note:
RST also serves as the In-System Programming (ISP) enable. ISP is enabled when the external
reset pin is held active. When ISP is disabled by fuse, ISP may only be entered by pulling RST
active during power-up. If this behavior is necessary, it is recommended to use an active-low reset
so that ISP can be entered by shorting RST to GND at power-up.
Figure 7-3.
Reset Pin Structure
VCC
VCC
POL = 1
POL = 0
DISRTO
WDT Reset
Internal Reset
RST
RST
Internal Reset
DISRTO
WDT Reset
7.4
Watchdog Reset
When the Watchdog times out, it will generate a reset pulse lasting 49 clock cycles. By default
this pulse is also output on the RST pin. To disable the RST output the DISRTO bit in AUXR
(Compatibility mode) or WDTCON (Fast mode) must be set to one. Watchdog reset will set the
WDTOVF flag in WDTCON. To prevent a Watchdog reset, the watchdog reset sequence
1EH/E1H must be written to WDTRST before the Watchdog times out. See “Programmable
Watchdog Timer” on page 73. for details on the operation of the Watchdog.
7.5
Software Reset
The CPU may generate a 49-clock cycle reset pulse by writing the software reset sequence
5AH/A5H to the WDRST register. A software reset will set the SWRST bit in WDTCON. See
“Software Reset” on page 73 for more information on software reset. Writing any sequences
other than 5AH/A5H or 1EH/E1H to WDTRST will generate an immediate reset and set both
WDTOVF and SWRST to flag an error. Software reset will also drive the RST pin active unless
DISRTO is set.
8. Power Saving Modes
The AT89LP51/52 supports two different power-reducing modes: Idle and Power-down. These
modes are accessed through the PCON register. Additional steps may be required to achieve
the lowest possible power consumption while using these modes.
8.1
Idle Mode
Setting the IDL bit in PCON enters idle mode. Idle mode halts the internal CPU clock. The CPU
state is preserved in its entirety, including the RAM, stack pointer, program counter, program
status word, and accumulator. The Port pins hold the logic states they had at the time that Idle
was activated. Idle mode leaves the peripherals running in order to allow them to wake up the
34
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
CPU when an interrupt is generated. The timer and UART peripherals continue to function during Idle. If these functions are not needed during idle, they should be explicitly disabled by
clearing the appropriate control bits in their respective SFRs. The watchdog may be selectively
enabled or disabled during Idle by setting/clearing the WDIDLE bit. The Brown-out Detector is
always active during Idle. Any enabled interrupt source or reset may terminate Idle mode. When
exiting Idle mode with an interrupt, the interrupt will immediately be serviced, and following RETI
the next instruction to be executed will be the one following the instruction that put the device
into Idle.
The power consumption during Idle mode can be further reduced by prescaling down the system
clock using the System Clock Divider (Section 6.4 on page 31). Be aware that the clock divider
will affect all peripheral functions and baud rates may need to be adjusted to maintain their rate
with the new clock frequency.
.
Table 8-1.
PCON – Power Control Register
PCON = 87H
Reset Value = 000X 0000B
Not Bit Addressable
SMOD1
SMOD0
PWDEX
POF
GF1
GF0
PD
IDL
7
6
5
4
3
2
1
0
Bit
Symbol
Function
SMOD1
Double Baud Rate bit. Doubles the baud rate of the UART in Modes 1, 2, or 3.
SMOD0
Frame Error Select. When SMOD0 = 1, SCON.7 is SM0. When SMOD0 = 1, SCON.7 is FE. Note that FE will be set after
a frame error regardless of the state of SMOD0.
PWDEX
Power-down Exit Mode. When PWDEX = 0, wake up from Power-down is externally controlled. When PWDEX = 1, wake
up from Power-down is internally timed.
POF
Power Off Flag. POF is set to “1” during power up (i.e. cold reset). It can be set or reset under software control and is not
affected by RST or BOD (i.e. warm resets).
GF1, GF0
General-purpose Flags
PD
Power-down bit. Setting this bit activates power-down operation. The PD bit is cleared automatically by hardware when
waking up from power-down.
IDL
Idle Mode bit. Setting this bit activates Idle mode operation. The IDL bit is cleared automatically by hardware when
waking up from idle
8.2
Power-down Mode
Setting the Power-down (PD) bit in PCON enters Power-down mode. Power-down mode stops
the oscillator, disables the BOD and powers down the Flash memory in order to minimize power
consumption. Only the power-on circuitry will continue to draw power during Power-down. During Power-down, the power supply voltage may be reduced to the RAM keep-alive voltage. The
RAM contents will be retained, but the SFR contents are not guaranteed once VDD has been
reduced. Power-down may be exited by external reset, power-on reset, or certain enabled
interrupts.
35
3709D–MICRO–12/11
8.2.1
Interrupt Recovery from Power-down
Two external interrupt sources may be configured to terminate Power-down mode: external
interrupts INT0 (P3.2) and INT1 (P3.3). To wake up by external interrupt INT0 or INT1, that interrupt must be enabled by setting EX0 or EX1 in IE and must be configured for level-sensitive
operation by clearing IT0 or IT1.
When terminating Power-down by an interrupt, two different wake-up modes are available.
When PWDEX in PCON is one, the wake-up period is internally timed as shown in Figure 8-1. At
the falling edge on the interrupt pin, Power-down is exited, the oscillator is restarted, and an
internal timer begins counting. The internal clock will not be allowed to propagate to the CPU
until after the timer has timed out. After the time-out period the interrupt service routine will
begin. The time-out period is controlled by the Start-up Timer Fuses (see Table 7-1 on page 33).
The interrupt pin need not remain low for the entire time-out period.
Figure 8-1.
Interrupt Recovery from Power-down (PWDEX = 1)
PWD
XTAL1
tSUT
INT1
Internal
Clock
When PWDEX = “0”, the wake-up period is controlled externally by the interrupt. Again, at the
falling edge on the interrupt pin, power-down is exited and the oscillator is restarted. However,
the internal clock will not propagate until the rising edge of the interrupt pin as shown in Figure 82. The interrupt pin should be held low long enough for the selected clock source to stabilize.
After the rising edge on the pin the interrupt service routine will be executed.
Figure 8-2.
Interrupt Recovery from Power-down (PWDEX = 0)
PWD
XTAL1
INT1
Internal
Clock
8.2.2
36
Reset Recovery from Power-down
The wake-up from Power-down through an external reset is similar to the interrupt with
PWDEX = “1”. At the rising edge of RST, Power-down is exited, the oscillator is restarted, and
an internal timer begins counting as shown in Figure 8-3. The internal clock will not be allowed to
propagate to the CPU until after the timer has timed out. The time-out period is controlled by the
Start-up Timer Fuses. (See Table 7-1 on page 33). If RST returns low before the time-out, a two
clock cycle internal reset is generated when the internal clock restarts. Otherwise, the device will
remain in reset until RST is brought low.
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 8-3.
Reset Recovery from Power-down (POL = 1)
PWD
XTAL1
tSUT
RST
Internal
Clock
Internal
Reset
8.3
Reducing Power Consumption
Several possibilities need consideration when trying to reduce the power consumption in an
8051-based system. Generally, Idle or Power-down mode should be used as often as possible.
All unneeded functions should be disabled. The System Clock Divider can scale down the operating frequency during periods of low demand. The ALE output can be disabled by setting
DISALE in AUXR, thereby also reducing EMI.
9. Interrupts
The AT89LP51/52 provides 6 interrupt sources: two external interrupts, three timer interrupts,
and a serial port interrupt. These interrupts and the system reset each have a separate program
vector at the start of the program memory space. Each interrupt source can be individually
enabled or disabled by setting or clearing a bit in the interrupt enable register IE. The IE register
also contains a global disable bit, EA, which disables all interrupts.
Each interrupt source can be individually programmed to one of four priority levels by setting or
clearing bits in the interrupt priority registers IP and IPH. IP holds the low order priority bits and
IPH holds the high priority bits for each interrupt. An interrupt service routine in progress can be
interrupted by a higher priority interrupt, but not by another interrupt of the same or lower priority.
The highest priority interrupt cannot be interrupted by any other interrupt source. If two requests
of different priority levels are pending at the end of an instruction, the request of higher priority
level is serviced. If requests of the same priority level are pending at the end of an instruction, an
internal polling sequence determines which request is serviced. The polling sequence is based
on the vector address; an interrupt with a lower vector address has higher priority than an interrupt with a higher vector address. Note that the polling sequence is only used to resolve pending
requests of the same priority level.
The External Interrupts INT0 and INT1 can each be either level-activated or edge-activated,
depending on bits IT0 and IT1 in Register TCON. The flags that actually generate these interrupts are the IE0 and IE1 bits in TCON. When the service routine is vectored to, hardware clears
the flag that generated an external interrupt only if the interrupt was edge-activated. If the interrupt was level activated, then the external requesting source (rather than the on-chip hardware)
controls the request flag.
The Timer 0 and Timer 1 Interrupts are generated by TF0 and TF1, which are set by a rollover in
their respective Timer/Counter registers (except for Timer 0 in Mode 3). When a timer interrupt is
generated, the on-chip hardware clears the flag that generated it when the service routine is
37
3709D–MICRO–12/11
vectored to. The Timer 2 Interrupt is generated by a logic OR of bits TF2 and EXF2 in register
T2CON. Neither of these flags is cleared by hardware when the CPU vectors to the service routine. The service routine normally must determine whether TF2 or EXF2 generated the interrupt
and that bit must be cleared by software.
The Serial Port Interrupt is generated by the logic OR of RI and TI in SCON. Neither of these
flags is cleared by hardware when the CPU vectors to the service routine. The service routine
normally must determine whether RI or TI generated the interrupt and that bit must be cleared by
software.
All of the bits that generate interrupts can be set or cleared by software, with the same result as
though they had been set or cleared by hardware. That is, interrupts can be generated and
pending interrupts can be canceled in software.
Table 9-1.
9.1
Interrupt Vector Addresses
Interrupt
Source
Vector Address
System Reset
RST or POR or BOD
0000H
External Interrupt 0
IE0
0003H
Timer 0 Overflow
TF0
000BH
External Interrupt 1
IE1
0013H
Timer 1 Overflow
TF1
001BH
Serial Port Interrupt
RI or TI
0023H
Timer 2 Interrupt
TF2 or EXF2
002BH
Interrupt Response Time
The interrupt flags may be set by their hardware in any clock cycle. The interrupt controller polls
the flags in the last clock cycle of the instruction in progress. If one of the flags was set in the
preceding cycle, the polling cycle will find it and the interrupt system will generate an LCALL to
the appropriate service routine as the next instruction, provided that the interrupt is not blocked
by any of the following conditions: an interrupt of equal or higher priority level is already in progress; the instruction in progress is RETI or any write to the IE, IP or IPH registers; the CPU is
currently forced into idle by an IAP or FDATA write. Each of these conditions will block the generation of the LCALL to the interrupt service routine. The second condition ensures that if the
instruction in progress is RETI or any access to IE, IP or IPH, then at least one more instruction
will be executed before any interrupt is vectored to. The polling cycle is repeated at the last cycle
of each instruction, and the values polled are the values that were present at the previous clock
cycle. If an active interrupt flag is not being serviced because of one of the above conditions and
is no longer active when the blocking condition is removed, the denied interrupt will not be serviced. In other words, the fact that the interrupt flag was once active but not serviced is not
remembered. Every polling cycle is new.
If a request is active and conditions are met for it to be acknowledged, a hardware subroutine
call to the requested service routine will be the next instruction executed. The call itself takes
four cycles. Thus, a minimum of five complete clock cycles elapsed between activation of an
interrupt request and the beginning of execution of the first instruction of the service routine. A
longer response time results if the request is blocked by one of the previously listed conditions. If
an interrupt of equal or higher priority level is already in progress, the additional wait time
depends on the nature of the other interrupt's service routine. If the instruction in progress is not
in its final clock cycle, the additional wait time cannot be more than 4 cycles, since the longest
38
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
instruction is 5 cycles long. If the instruction in progress is RETI, the additional wait time cannot
be more than 9 cycles (a maximum of 4 more cycles to complete the instruction in progress, plus
a maximum of 5 cycles to complete the next instruction). Thus, in a single-interrupt system, the
response time is always more than 5 clock cycles and less than 14 clock cycles. See Figure 9-1
and Figure 9-2.
Figure 9-1.
Minimum Interrupt Response Time (Fast Mode)
Clock Cycles
1
5
INT0
IE0
Instruction
Figure 9-2.
Ack.
Cur. Instr.
LCALL
1st ISR Instr.
Maximum Interrupt Response Time (Fast Mode)
Clock Cycles
1
5
10
14
INT0
Ack.
IE0
Instruction
Figure 9-3.
RETI
MOVX @/DPTR, A
LCALL
1st ISR Instr.
Minimum Interrupt Response Time (Compatibility Mode)
Clock Cycles
1
INT0
14
Ack.
IE0
Instruction
Figure 9-4.
LCALL
ISR
Maximum Interrupt Response Time (Compatibility Mode)
Clock Cycles
1
13
37
49
INT0
Ack.
IE0
Instruction
RETI
MUL AB
LCALL
ISR
39
3709D–MICRO–12/11
Table 9-2.
IE – Interrupt Enable Register
IE = A8H
Reset Value = 0000 0000B
Bit Addressable
Bit
EA
–
ET2
ES
ET1
EX1
ET0
EX0
7
6
5
4
3
2
1
0
Symbol
Function
EA
Global enable/disable. All interrupts are disabled when EA = 0. When EA = 1, each interrupt source is enabled/disabled by setting
/clearing its own enable bit.
ET2
Timer 2 Interrupt Enable
ES
Serial Port Interrupt Enable
ET1
Timer 1 Interrupt Enable
EX1
External Interrupt 1 Enable
ET0
Timer 0 Interrupt Enable
EX0
External Interrupt 0 Enable
Table 9-3.
IP – Interrupt Priority Register
IP = B8H
Reset Value = 0000 0000B
Bit Addressable
Bit
–
–
PT2
PS
PT1
PX1
PT0
PX0
7
6
5
4
3
2
1
0
Symbol
Function
PT2
Timer 2 Interrupt Priority Low
PS
Serial Port Interrupt Priority Low
PT1
Timer 1 Interrupt Priority Low
PX1
External Interrupt 1 Priority Low
PT0
Timer 0 Interrupt Priority Low
PX0
External Interrupt 0 Priority Low
Table 9-4.
IPH – Interrupt Priority High Register
IPH = B7H
Reset Value = 0000 0000B
Not Bit Addressable
Bit
–
–
PT2H
PSH
PT1H
PX1H
PT0H
PX0H
7
6
5
4
3
2
1
0
Symbol
Function
PT2H
Timer 2 Interrupt Priority High
PSH
Serial Port Interrupt Priority High
PT1H
Timer 1 Interrupt Priority High
PX1H
External Interrupt 1 Priority High
PT0H
Timer 0 Interrupt Priority High
PX0H
External Interrupt 0 Priority High
40
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
10. I/O Ports
The AT89LP51/52 can be configured for between 32 and 36 I/O pins. The exact number of I/O
pins available depends on the clock, external memory and package type as shown in Table 101.
Table 10-1.
I/O Pin Configurations
Clock Source
External Program Access
External Data Access
Number of I/O
Pins
Yes (RD+WR)
14
No
16
Yes (ALE+RD+WR+P0)
31
No
34
Yes (RD+WR)
15
No
17
Yes (ALE+RD+WR+P0)
32
No
35
Yes (RD+WR)
16
No
18
Yes (ALE+RD+WR+P0)
33
No
36
Yes (PSEN+ALE+P0+P2)
External Crystal or
Resonator
No
Yes (PSEN+ALE+P0+P2)
External Clock
No
Yes (PSEN+ALE+P0+P2)
Internal RC
Oscillator
No
10.1
Port Configuration
Each 8-bit port on the AT89LP51/52 may be configured in one of four modes: quasi-bidirectional
(standard 8051 port outputs), push-pull output, open-drain output, or input-only. Port modes may
be assigned in software on a port-by-port basis as shown in Table 10-2 using the PMOD register
listed in Table 10-3. The Tristate-Port User Fuse determines the default state of the port pins
(See “User Configuration Fuses” on page 86). When the fuse is enabled, all port pins default to
input-only mode after reset. When the fuse is disabled, all port pins on P1, P2 and P3 default to
quasi-bidirectional mode after reset and are weakly pulled high. P0 is set to Open-drain mode.
P4 always operates in quasi-bidirectional mode.
Each port pin also has a Schmitt-triggered input for improved input noise rejection. During
Power-down all the Schmitt-triggered inputs are disabled with the exception of P3.2 (INT0), P3.3
(INT1), RST, P4.6 (XTAL1) and P4.7 (XTAL2). Therefore, P3.2, P3.3, P4.6 and P4.7 should not
be left floating during Power-down.
.
Table 10-2.
Configuration Modes for Port x
PxM0
PxM1
Port Mode
0
0
Quasi-bidirectional
0
1
Push-pull Output
1
0
Input Only (High Impedance)
1
1
Open-Drain Output
41
3709D–MICRO–12/11
.
Table 10-3.
PMOD – Port Mode Register
PMOD = C1H
Reset Value = 0000 0011B
Not Bit Addressable
Bit
P3M1
P3M0
P2M1
P2M0
P1M1
P1M0
P0M1
P0M0
7
6
5
4
3
2
1
0
Symbol
Function
P3M1-0
Port 3 Configuration Mode
P2M1-0
Port 2 Configuration Mode
P1M1-0
Port 1 Configuration Mode
P0M1-0
Port 0 Configuration Mode
10.1.1
Quasi-bidirectional Output
Port pins in quasi-bidirectional output mode function similar to standard 8051 port pins. A Quasibidirectional port can be used both as an input and output without the need to reconfigure the
port. This is possible because when the port outputs a logic high, it is weakly driven, allowing an
external device to pull the pin low. When the pin is driven low, it is driven strongly and able to
sink a large current. There are three pull-up transistors in the quasi-bidirectional output that
serve different purposes.
One of these pull-ups, called the “very weak” pull-up, is turned on whenever the port latch for the
pin contains a logic “1”. This very weak pull-up sources a very small current that will pull the pin
high if it is left floating. When the pin is pulled low externally this pull-up will always source some
current.
A second pull-up, called the “weak” pull-up, is turned on when the port latch for the pin contains
a logic “1” and the pin itself is also at a logic “1” level. This pull-up provides the primary source
current for a quasi-bidirectional pin that is outputting a “1”. If this pin is pulled low by an external
device, this weak pull-up turns off, and only the very weak pull-up remains on. In order to pull the
pin low under these conditions, the external device has to sink enough current to overpower the
weak pull-up and pull the port pin below its input threshold voltage.
The third pull-up is referred to as the “strong” pull-up. This pull-up is used to speed up low-tohigh transitions on a quasi-bidirectional port pin when the port latch changes from a logic “0” to a
logic “1”. When this occurs, the strong pull-up turns on for one CPU clock, quickly pulling the port
pin high. The quasi-bidirectional port configuration is shown in Figure 10-1.
10.1.2
Input-only Mode
The input only port configuration is shown in Figure 10-2. The output drivers are tristated. The
input includes a Schmitt-triggered input for improved input noise rejection. The input circuitry of
P3.2, P3.3, P4.6 and P4.7 is not disabled during Power-down (see Figure 10-3) and therefore
these pins should not be left floating during Power-down when configured in this mode.
Input-only mode can reduce power consumption for low-level inputs over quasi-bidirectional
mode because the “very weak” pull-up is turned off and only very small leakage current in the
sub microamp range is present.
42
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 10-1. Quasi-bidirectional Output
1 Clock Delay
(D Flip-Flop)
VCC
VCC
VCC
Strong
Very
Weak
Weak
Por t
Pin
From Por t
Register
Input
Data
PWD
Figure 10-2. Input Only
Input
Data
Por t
Pin
PWD
Figure 10-3. Input Circuit for P3.2, P3.3, P4.6 and P4.7
Input
Data
10.1.3
Port
Pin
Open-drain Output
The open-drain output configuration turns off all pull-ups and only drives the pull-down transistor
of the port pin when the port latch contains a logic “0”. To be used as a logic output, a port configured in this manner must have an external pull-up, typically a resistor tied to VDD. The pulldown for this mode is the same as for the quasi-bidirectional mode. The open-drain port configuration is shown in Figure 10-4. The input circuitry of P3.2, P3.3, P4.6 and P4.7 is not disabled
during Power-down (see Figure 10-3) and therefore these pins should not be left floating during
Power-down when configured in this mode.
Figure 10-4. Open-Drain Output
Por t
Pin
From Por t
Register
Input
Data
PWD
43
3709D–MICRO–12/11
10.1.4
Push-pull Output
The push-pull output configuration has the same pull-down structure as both the open-drain and
the quasi-bidirectional output modes, but provides a continuous strong pull-up when the port
latch contains a logic “1”. The push-pull mode may be used when more source current is needed
from a port output. The push-pull port configuration is shown in Figure 10-5.
Figure 10-5. Push-pull Output
VCC
Por t
Pin
From Por t
Register
Input
Data
PWD
10.2
Port Read-Modify-Write
A read from a port will read either the state of the pins or the state of the port register depending
on which instruction is used. Simple read instructions will always access the port pins directly.
Read-modify-write instructions, which read a value, possibly modify it, and then write it back, will
always access the port register. This includes bit write instructions such as CLR or SETB as they
actually read the entire port, modify a single bit, then write the data back to the entire port. See
Table 10-4 for a complete list of Read-Modify-Write instruction which may access the ports.
Table 10-4.
44
Port Read-Modify-Write Instructions
Mnemonic
Instruction
Example
ANL
Logical AND
ANL P1, A
ORL
Logical OR
ORL P1, A
XRL
Logical EX-OR
XRL P1, A
JBC
Jump if bit set and clear bit
JBC P3.0, LABEL
CPL
Complement bit
CPL P3.1
INC
Increment
INC P1
DEC
Decrement
DEC P3
DJNZ
Decrement and jump if not zero
DJNZ P3, LABEL
MOV PX.Y, C
Move carry to bit Y of Port X
MOV P1.0, C
CLR PX.Y
Clear bit Y of Port X
CLR P1.1
SETB PX.Y
Set bit Y of Port X
SETB P3.2
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
10.3
Port Alternate Functions
Most general-purpose digital I/O pins of the AT89LP51/52 share functionality with the various
I/Os needed for the peripheral units. Table 10-6 lists the alternate functions of the port pins.
Alternate functions are connected to the pins in a logic AND fashion. In order to enable the
alternate function on a port pin, that pin must have a “1” in its corresponding port register bit,
otherwise the input/output will always be “0”. However, alternate functions may be temporarily
forced to “0” by clearing the associated port bit, provided that the pin is not in input-only mode.
Furthermore, each pin must be configured for the correct input/output mode as required by its
peripheral before it may be used as such. Table 10-5 shows how to configure a generic pin for
use with an alternate function. If two or more port pins on the same 8-bit require difference directions, the port must be configured for bidirectional operation.
Table 10-5.
Pin Function Configurations for Port x Pin y
PxM0
PxM1
Px.y
0
0
1
bidirectional (internal pull-up)
0
1
1
output
1
0
X
input
1
1
1
bidirectional (external pull-up)
Table 10-6.
Port Pin Alternate Functions
Configuration Bits
Port Pin
I/O Mode
PxM0
P0.0–P0.7
PxM1
N/A
Alternate
Function
AD0–AD7
Address and data on Port 0 are
automatically configured as output
or input regardless of P0M0 and
P0M1.
T2 Clock out toggles P1.0 directly
P1.0
P1M0
P1M1
T2
P1.1
P1M0
P1M1
T2EX
P1.5
P1M0
P1M1
MOSI
P1.6
P1M0
P1M1
MISO
P1.7
P1M0
P1M1
SCK
P2.0–P2.7
N/A
Notes
A8–A15
Address on Port 2 is automatically
configured as output regardless of
P2M0 and P2M1.
P3.0
P3M0
P3M1
RXD
P3.1
P3M0
P3M1
TXD
P3.2
P3M0
P3M1
INT0
P3.3
P3M0
P3M1
INT1
P3.4
P3M0
P3M1
T0
T0 Clock out toggles P3.4 directly
P3.5
P3M0
P3M1
T1
T1 Clock out toggles P3.5 directly
P3.6
P3M0
P3M1
WR
P3.7
P3M0
P3M1
RD
45
3709D–MICRO–12/11
11. Timer 0 and Timer 1
The AT89LP51/52 has two 16-bit Timer/Counters, Timer 0 and Timer 1, with the following
features:
• Two independent 16-bit timer/counters with 8-bit reload registers
• UART baud rate generation using Timer 1
• Output pin toggle on timer overflow
• Split timer mode allows for three separate timers (2 8-bit, 1 16-bit)
• Gated modes allow timers to run/halt based on an external input
Timer 0 and Timer 1 have similar modes of operation. As timers, the timer registers normally
increase every clock cycle. Thus, the registers count clock cycles. The timer rate can be prescaled by a value between 1 and 16 using the Timer Prescaler (see Table 6-2 on page 31). Both
Timers share the same prescaler. In Compatibility mode CDV defaults to 2, so a clock cycle consists of two oscillator periods,and the prescaler defaults to 6 making the count rate equal to 1/12
of the oscillator frequency. By default in Fast mode CDV = 0 and TPS = 0 so the count rate is
equal to the oscillator frequency.
As counters, the timer registers are incremented in response to a 1-to-0 transition at the corresponding input pins, T0 or T1. In Fast mode the external input is sampled every clock cycle.
When the samples show a high in one cycle and a low in the next cycle, the count is incremented. The new count value appears in the register during the cycle following the one in which
the transition was detected. Since 2 clock cycles are required to recognize a 1-to-0 transition,
the maximum count rate is 1/2 of the system frequency. There are no restrictions on the duty
cycle of the input signal, but it should be held for at least one full clock cycle to ensure that a
given level is sampled at least once before it changes.
In Compatibility mode the counter input sampling is controlled by the prescaler. Since TPS
defaults to 6 in this mode, the pins are sampled every six system clocks. Therefore the input signal should be held for at least six clock cycles to ensure that a given level is sampled at least
once before it changes.
Furthermore, the Timer or Counter functions for Timer 0 and Timer 1 have four operating modes:
13-bit timer, 16-bit timer, 8-bit auto-reload timer, and split timer. The control bits C/T in the Special Function Register TMOD select the Timer or Counter function. The bit pairs (M1, M0) in
TMOD select the operating modes.
Table 11-1.
46
Timer 0/1 Register Summary
Name
Address
Purpose
Bit-Addressable
TCON
88H
Control
Y
TMOD
89H
Mode
N
TL0
8AH
Timer 0 low-byte
N
TL1
8BH
Timer 1 low-byte
N
TH0
8CH
Timer 0 high-byte
N
TH1
8DH
Timer 1 high-byte
N
TCONB
91H
Mode
N
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
11.1
Mode 0 – 13-bit Timer/Counter
Both Timers in Mode 0 are 8-bit Counters with a divide-by-32 prescaler. Figure 11-1 shows the
Mode 0 operation as it applies to Timer 1. As the count rolls over from all “1”s to all “0”s, it sets
the Timer interrupt flag TF1. The counter input is enabled to the Timer when TR1 = 1 and either
GATE1 = 0 or INT1 = 1. Setting GATE1 = 1 allows the Timer to be controlled by external input
INT1, to facilitate pulse width measurements. TR1 is a control bit in the Special Function Register TCON. GATE1 is in TMOD. The 13-bit register consists of all 8 bits of TH1 and the lower 5
bits of TL1. The upper 3 bits of TL1 are indeterminate and should be ignored. Setting the run flag
(TR1) does not clear the registers.
8192
Time-out Period = -------------------------------------------------- × ( TPS + 1 )
System Frequency
Mode 0:
Figure 11-1. Timer/Counter 1 Mode 0: 13-bit Counter
OSC
÷CDV
÷TPS
C/T = 0
TL1
(5 Bits)
TH1
(8 Bits)
TF1
Interrupt
C/T = 1
T1 Pin
Control
TR1
GATE1
INT1 Pin
Mode 0 operation is the same for Timer 0 as for Timer 1, except that TR0, TF0, GATE0 and
INT0 replace the corresponding Timer 1 signals in Figure 11-1. There are two different C/T bits,
one for Timer 1 (TMOD.6) and one for Timer 0 (TMOD.2).
11.2
Mode 1 – 16-bit Timer/Counter
In Mode 1 the Timers are configured for 16-bit operation. The Timer register is run with all 16 bits
and the clock is applied to the combined high and low timer registers (TH1/TL1). As clock pulses
are received, the timer counts up: 0000H, 0001H, 0002H, etc. An overflow occurs on the
FFFFH-to-0000H transition, upon which the overflow flag bit in TCON is set. See Figure 11-2.
Mode 1 operation is the same for Timer/Counter 0.
Mode 1:
65536
Time-out Period = -------------------------------------------------- × ( TPS + 1 )
System Frequency
Figure 11-2. Timer/Counter 1 Mode 1: 16-bit Counter
OSC
÷CDV
÷TPS
C/T = 0
TL1
(8 Bits)
TH1
(8 Bits)
TF1
Interrupt
C/T =1
T1 Pin
Control
TR1
GATE1
INT1 Pin
47
3709D–MICRO–12/11
11.3
Mode 2 – 8-bit Auto-Reload Timer/Counter
Mode 2 configures the Timer register as an 8-bit Counter (TL1) with automatic reload, as shown
in Figure 11-3. Overflow from TL1 not only sets TF1, but also reloads TL1 with the contents of
TH1, which is preset by software. The reload leaves TH1 unchanged. Mode 2 operation is the
same for Timer/Counter 0.
( 256 – TH0 )
Time-out Period = -------------------------------------------------- × ( TPS + 1 )
System Frequency
Mode 2:
Figure 11-3. Timer/Counter 1 Mode 2: 8-bit Auto-Reload
÷CDV
OSC
÷TPS
C/T = 0
TL1
(8 Bits)
TF1
Interrupt
C/T = 1
Control
T1 Pin
Reload
TR1
TH1
(8 Bits)
GATE1
INT0 Pin
11.4
Mode 3 – 8-bit Split Timer
Timer 1 in Mode 3 simply holds its count. The effect is the same as setting TR1 = 0. Timer 0 in
Mode 3 establishes TL0 and TH0 as two separate counters. The logic for Mode 3 on Timer 0 is
shown in Figure 11-4. TL0 uses the Timer 0 control bits: C/T, GATE0, TR0, INT0, and TF0. TH0
is locked into a timer function (counting clock cycles) and takes over the use of TR1 and TF1
from Timer 1. Thus, TH0 now controls the Timer 1 interrupt. While Timer 0 is in Mode 3, Timer 1
will still obey its settings in TMOD but cannot generate an interrupt.
Mode 3 is for applications requiring an extra 8-bit timer or counter. With Timer 0 in Mode 3, the
AT89LP51/52 can appear to have four Timer/Counters. When Timer 0 is in Mode 3, Timer 1 can
be turned on and off by switching it out of and into its own Mode 3. In this case, Timer 1 can still
be used by the serial port as a baud rate generator or in any application not requiring an
interrupt.
Figure 11-4. Timer/Counter 0 Mode 3: Two 8-bit Counters
OSC
÷CDV
÷TPS
C/T = 0
C/T =1
T0 Pin
(8 Bits)
Interrupt
(8 Bits)
Interrupt
Control
GATE0
INT0 Pin
OSC
÷CDV
÷TPS
Control
48
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
.
Table 11-2.
TCON – Timer/Counter Control Register
TCON = 88H
Reset Value = 0000 0000B
Bit Addressable
Bit
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
7
6
5
4
3
2
1
0
Symbol
Function
TF1
Timer 1 overflow flag. Set by hardware on Timer/Counter overflow. Cleared by hardware when the processor vectors
to interrupt routine.
TR1
Timer 1 run control bit. Set/cleared by software to turn Timer/Counter on/off.
TF0
Timer 0 overflow flag. Set by hardware on Timer/Counter overflow. Cleared by hardware when the processor vectors
to interrupt routine.
TR0
Timer 0 run control bit. Set/cleared by software to turn Timer/Counter on/off.
IE1
Interrupt 1 edge flag. Set by hardware when external interrupt edge detected. Cleared when interrupt processed.
IT1
Interrupt 1 type control bit. Set/cleared by software to specify falling edge/low level triggered external interrupts.
IE0
Interrupt 0 edge flag. Set by hardware when external interrupt edge detected. Cleared when interrupt processed.
IT0
Interrupt 0 type control bit. Set/cleared by software to specify falling edge/low level triggered external interrupts.
Table 11-3.
TCONB – Timer/Counter Control Register B
TCONB = 91H
Reset Value = 0000 0000B
Not Bit Addressable
Bit
T1OE
T0OE
SPEN
–
–
–
–
–
7
6
5
4
3
2
1
0
Symbol
Function
T1OE
Timer 1 Output Enable. Configures Timer 1 to toggle T1 (P3.5) upon overflow.
T0OE
Timer 0 Output Enable. Configures Timer 0 to toggle T0 (P3.4) upon overflow.
SPEN
Enables SPI mode for UART mode 0
11.5
Clock Output (Pin Toggle Mode)
On the AT89LP51/52, Timer 0 and Timer 1 may be independently configured to toggle their
respective counter pins, T0 and T1, on overflow by setting the T0OE or T1OE bits in TCONB.
The C/Tx bits must be set to “0” when in toggle mode and the T0 (P3.4) and T1 (P3.5) pins must
be configured in an output mode. The Timer Overflow Flags and Interrupts will continue to function while in toggle mode and Timer 1 may still generate the baud rate for the UART. The timer
GATE function also works in toggle mode, allowing the output to be halted by an external input.
Toggle mode can be used with Timer Mode 2 to output a 50% duty cycle clock with 8-bit programmable frequency. Tx is toggled at every Timer x overflow with the pulse width determined
by the value of THx. An example waveform is given in Figure 11-5. The following formula gives
the output frequency for Timer 0 in Mode 2.
Mode 2:
System Frequency
1
f out = -------------------------------------------------- × --------------------2 × ( 256 – TH0 )
TPS + 1
49
3709D–MICRO–12/11
Figure 11-5. Timer 0/1 Toggle Mode 2 Waveform
FFh
THx
Tx
Table 11-4.
TMOD – Timer/Counter Mode Control Register
TMOD Address = 089H
Reset Value = 0000 0000B
Not Bit Addressable
Bit
GATE1
C/T1
T1M1
T1M0
GATE0
C/T0
T0M0
T0M1
7
6
5
4
3
2
1
0
Symbol
Function
GATE1
Timer 1 Gating Control. When set, Timer/Counter 1 is enabled only while INT1 pin is high and TR1 control pin is set.
When cleared, Timer 1 is enabled whenever TR1 control bit is set.
C/T1
Timer or Counter Selector 1. Cleared for Timer operation (input from internal system clock). Set for Counter operation
(input from T1 input pin). C/T1 must be zero when using Timer 1 in Clock Out mode.
T1M1
T1M0
Timer 1 Operating Mode
Mode
T1M1
T1M0
Operation
0
0
0
13-bit Timer Mode. 8-bit Timer/Counter TH1 with TL1 as 5-bit prescaler.
1
0
1
16-bit Timer Mode. TH1 and TL1 are cascaded to form a 16-bit Timer/Counter.
2
1
0
8-bit Auto Reload Mode. TH1 holds a value which is reloaded into 8-bit Timer/Counter
TL1 each time it overflows.
3
1
1
Timer/Counter 1 is stopped
GATE0
Timer 0 Gating Control. When set, Timer/Counter 0 is enabled only while INT0 pin is high and TR0 control pin is set.
When cleared, Timer 0 is enabled whenever TR0 control bit is set.
C/T0
Timer or Counter Selector 0. Cleared for Timer operation (input from internal system clock). Set for Counter operation
(input from T0 input pin). C/T0 must be zero when using Timer 0 in Clock Out mode.
T0M1
T0M0
50
Timer 0 Operating Mode
Mode
T0M1
T0M0
Operation
0
0
0
13-bit Timer Mode. 8-bit Timer/Counter TH0 with TL0 as 5-bit prescaler.
1
0
1
16-bit Timer Mode. TH0 and TL0 are cascaded to form a 16-bit Timer/Counter.
2
1
0
8-bit Auto Reload Mode. TH0 holds a value which is reloaded into 8-bit Timer/Counter
TL0 each time it overflows.
3
1
1
Split Timer Mode. TL0 is an 8-bit Timer/Counter controlled by the standard Timer 0
control bits. TH0 is an 8-bit timer only controlled by Timer 1 control bits.
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
12. Timer 2
The AT89LP51/52 includes a 16-bit Timer/Counter 2 with the following features:
• 16-bit timer/counter with one 16-bit reload/capture register
• One external reload/capture input
• Up/Down counting mode with external direction control
• UART baud rate generation
• Output-pin toggle on timer overflow
• Dual slope symmetric operating modes
• Timer 2 is included in AT89LP51, unlike AT89S51.
Timer 2 is a 16-bit Timer/Counter that can operate as either a timer or an event counter. The
type of operation is selected by bit C/T2 in the SFR T2CON. Timer 2 has three operating modes:
capture, auto-reload (up or down counting), and baud rate generator. The modes are selected
by bits in T2CON and T2MOD, as shown in Table 12-3. Timer 2 also serves as the time base for
the Compare/Capture Array (See Section 13. “External Interrupts” on page 57).
Timer 2 consists of two 8-bit registers, TH2 and TL2. In the Timer function, the register is incremented every clock cycle. Since a clock cycle consists of one oscillator period, the count rate is
equal to the oscillator frequency. The timer rate can be prescaled by a value between 1 and 16
using the Timer Prescaler (see Table 6-2 on page 31).
In the Counter function, the register is incremented in response to a 1-to-0 transition at its corresponding external input pin, T2. In this function, the external input is sampled every clock cycle.
When the samples show a high in one cycle and a low in the next cycle, the count is incremented. The new count value appears in the register during the cycle following the one in which
the transition was detected. Since two clock cycles are required to recognize a 1-to-0 transition,
the maximum count rate is 1/2 of the oscillator frequency. To ensure that a given level is sampled at least once before it changes, the level should be held for at least one full clock cycle.
Table 12-1.
Timer 2 Operating Modes
RCLK + TCLK
CP/RL2
DCEN
T2OE
TR2
MODE
0
0
0
0
1
16-bit Auto-reload
0
0
1
0
1
16-bit Auto-reload Up-Down
0
1
X
0
1
16-bit Capture
1
X
X
X
1
Baud Rate Generator
X
X
X
1
1
Frequency Generator
X
X
X
X
0
(Off)
The following definitions for Timer 2 are used in the subsequent paragraphs:
Table 12-2.
Symbol
Timer 2 Definitions
Definition
MIN
0000H
MAX
FFFFH
BOTTOM
16-bit value of {RCAP2H,RCAP2L}
51
3709D–MICRO–12/11
12.1
Timer 2 Registers
Control and status bits for Timer 2 are contained in registers T2CON (see Table 12-3) and
T2MOD (see Table 12-4). The register pair {TH2, TL2} at addresses 0CDH and 0CCH are the
16-bit timer register for Timer 2. The register pair {RCAP2H, RCAP2L} at addresses 0CBH and
0CAH are the 16-bit Capture/Reload register for Timer 2 in capture and auto-reload modes.
Table 12-3.
T2CON – Timer/Counter 2 Control Register
T2CON Address = 0C8H
Reset Value = 0000 0000B
Bit Addressable
Bit
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
C/T2
CP/RL2
7
6
5
4
3
2
1
0
Symbol
Function
TF2
Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set when either
RCLK = 1 or TCLK = 1.
EXF2
Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1.
When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be
cleared by software. EXF2 does not cause an interrupt in up/down counter mode (DCEN = 1) or dual-slope mode.
RCLK
Receive clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock in serial port
Modes 1 and 3. RCLK = 0 causes Timer 1 overflows to be used for the receive clock.
TCLK
Transmit clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock in serial port
Modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.
EXEN2
Timer 2 external enable. When set, allows a capture or reload to occur as a result of a negative transition on T2EX if
Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX.
TR2
Start/Stop control for Timer 2. TR2 = 1 starts the timer.
C/T2
Timer or counter select for Timer 2. C/T2 = 0 for timer function. C/T2 = 1 for external event counter (falling edge
triggered).
CP/RL2
Capture/Reload select. CP/RL2 = 1 causes captures to occur on negative transitions at T2EX if EXEN2 = 1. CP/RL2 = 0
causes automatic reloads to occur when Timer 2 overflows or negative transitions occur at T2EX when EXEN2 = 1. When
either RCLK or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow.
Table 12-4.
T2MOD – Timer 2 Mode Control Register
T2MOD Address = 0C9H
Reset Value = 0000 0000B
Not Bit Addressable
Bit
–
–
–
–
–
–
T2OE
DCEN
7
6
5
4
3
2
1
0
Symbol
Function
T2OE
Timer 2 Output Enable. When T2OE = 1 and C/T2 = 0, the T2 pin will toggle after every Timer 2 overflow.
DCEN
Timer 2 Down Count Enable. When Timer 2 operates in Auto-Reload mode and EXEN2 = 1, setting DCEN = 1 will cause
Timer 2 to count up or down depending on the state of T2EX.
52
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
12.2
Capture Mode
In the Capture mode, Timer 2 is a fixed 16-bit timer or counter that counts up from MIN to MAX.
An overflow from MAX to MIN sets bit TF2 in T2CON. If EXEN2 = 1, a 1-to-0 transition at external input T2EX also causes the current value in TH2 and TL2 to be captured into RCAP2H and
RCAP2L, respectively. In addition, the transition at T2EX causes bit EXF2 in T2CON to be set.
The EXF2 and TF2 bits can generate an interrupt. Capture mode is illustrated in Figure 12-1.
The Timer 2 overflow rate in Capture mode is given by the following equation:
65536
Time-out Period = -------------------------------------------------- × ( TPS + 1 )
System Frequency
Capture Mode:
Figure 12-1. Timer 2 Diagram: Capture Mode
OSC
÷CDV
÷TPS
C/T2 = 0
TL2
TH2
TF2
OVERFLOW
TR2
C/T2 = 1
CAPTURE
T2 PIN
RCAP2L
RCAP2H
TRANSITION
DETECTOR
TIMER 2
INTERRUPT
T2EX PIN
EXF2
EXEN2
12.3
Auto-Reload Mode
Timer 2 can be programmed to count up or down when configured in its 16-bit auto-reload
mode. This feature is invoked by the DCEN (Down Counter Enable) bit located in the SFR
T2MOD (see Table 12-4). Upon reset, the DCEN bit is set to 0 so that timer 2 will default to
count up. When DCEN is set, Timer 2 can count up or down, depending on the value of the
T2EX pin. A summary of the Auto-Reload behaviors is listed in Table 12-5.
Table 12-5.
12.3.1
Summary of Auto-Reload Modes
DCEN
T2EX
Direction
Behavior
0
X
Up
BOTTOM →MAX reload to BOTTOM
1
0
Down
MAX →BOTTOM underflow to MAX
1
1
Up
BOTTOM →MAX overflow to BOTTOM
Up Counter
Figure 12-2 shows Timer 2 automatically counting up when DCEN = 0. In this mode Timer 2
counts up to MAX and then sets the TF2 bit upon overflow. The overflow also causes the timer
registers to be reloaded with BOTTOM, the 16-bit value in RCAP2H and RCAP2L. If EXEN2 = 1,
a 16-bit reload can be triggered either by an overflow or by a 1-to-0 transition at external input
T2EX. This transition also sets the EXF2 bit. Both the TF2 and EXF2 bits can generate an interrupt. The Timer 2 overflow rate for this mode is given in the following equation:
Auto-Reload Mode:
65536 – {RCAP2H , RCAP2L}
Time-out Period = ------------------------------------------------------------------------------- × ( TPS + 1 )
System Frequency
DCEN = 0
53
3709D–MICRO–12/11
Figure 12-2. Timer 2 Diagram: Auto-Reload Mode (DCEN = 0)
OSC
÷CDV
÷TPS
TL2
TH2
Figure 12-3. Timer 2 Waveform: Auto-Reload Mode (DCEN = 0)
TF2 Set
MAX
BOTTOM
MIN
12.3.2
Up or Down Counter
Setting DCEN = 1 enables Timer 2 to count up or down, as shown in Figure 12-5. In this mode,
the T2EX pin controls the direction of the count (if EXEN2 = 1). A logic 1 at T2EX makes Timer 2
count up. When T2CM1-0 = 00B, the timer will overflow at MAX and set the TF2 bit. This overflow
also causes BOTTOM, the 16-bit value in RCAP2H and RCAP2L, to be reloaded into the timer
registers, TH2 and TL2, respectively. A logic 0 at T2EX makes Timer 2 count down. The timer
underflows when TH2 and TL2 equal BOTTOM, the 16-bit value stored in RCAP2H and
RCAP2L. The underflow sets the TF2 bit and causes MAX to be reloaded into the timer registers. The EXF2 bit toggles whenever Timer 2 overflows or underflows and can be used as a 17th
bit of resolution. In this operating mode, EXF2 does not flag an interrupt.
The behavior of Timer 2 when DCEN is enabled is shown in Figure 12-4.
Figure 12-4. Timer 2 Waveform: Auto-Reload Mode (DCEN = 1)
TF2 Set
MAX
BOTTOM
MIN
T2EX
EXF2
54
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 12-5. Timer 2 Diagram: Auto-Reload Mode (DCEN = 1)
÷TPS
The timer overflow/underflow rate for up-down counting mode is the same as for up counting
mode, provided that the count direction does not change. Changes to the count direction may
result in longer or shorter periods between time-outs.
12.4
Baud Rate Generator
Timer 2 is selected as the baud rate generator by setting TCLK and/or RCLK in T2CON (Table
12-3). Note that the baud rates for transmit and receive can be different if Timer 2 is used for the
receiver or transmitter and Timer 1 is used for the other function. Setting RCLK and/or TCLK
puts Timer 2 into its baud rate generator mode, as shown in Figure 12-6.
The baud rate generator mode is similar to the auto-reload mode, in that a rollover in TH2
causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2H and
RCAP2L, which are preset by software.
The baud rates in UART Modes 1 and 3 are determined by Timer 2’s overflow rate according to
the following equation.
Timer 2 Overflow Rate
Modes 1 and 3 Baud Rates = -----------------------------------------------------------16
The Timer can be configured for either timer or counter operation. In most applications, it is configured for timer operation (CP/T2 = 0). The baud rate formulas are given below.
Modes 1, 3
System Frequency
= -------------------------------------------------------------------------------------------------------------------------------16
×
(
TPS
+
1
)
× [ 65536 – ( RCAP2H,RCAP2L ) ]
Baud Rate
where (RCAP2H, RCAP2L) is the content of RCAP2H and RCAP2L taken as a 16-bit unsigned
integer.
Timer 2 as a baud rate generator is shown in Figure 12-6. This figure is valid only if RCLK or
TCLK = 1 in T2CON. Note that a rollover in TH2 does not set TF2 and will not generate an interrupt. Note too, that if EXEN2 is set, a 1-to-0 transition in T2EX will set EXF2 but will not cause a
reload from (RCAP2H, RCAP2L) to (TH2, TL2). Thus when Timer 2 is in use as a baud rate generator, T2EX can be used as an extra external interrupt. Also note that the Baud Rate and
Frequency Generator modes may be used simultaneously.
55
3709D–MICRO–12/11
Figure 12-6. Timer 2 in Baud Rate Generator Mode
TIMER 1 OVERFLOW
÷2
"0"
OSC
÷CDV
"1"
SMOD1
C/T2 = 0
"1"
TL2
"0"
TH2
RCLK
÷16
TR2
Rx
CLOCK
C/T2 = 1
"1"
"0"
T2 PIN
RCAP2L
EXEN2
TRANSITION
DETECTOR
÷ 16
T2EX PIN
12.5
TCLK
RCAP2H
Tx
CLOCK
TIMER 2
INTERRUPT
EXF2
Frequency Generator (Programmable Clock Out)
Timer 2 can generate a 50% duty cycle clock on T2 (P1.0), as shown in Figure 13.. This pin,
besides being a regular I/O pin, has two alternate functions. It can be programmed to input the
external clock for Timer/Counter 2 or to toggle its output at every timer overflow. To configure
the Timer/Counter 2 as a clock generator, bit C/T2 (T2CON.1) must be cleared and bit T2OE
(T2MOD.1) must be set. Bit TR2 (T2CON.2) starts and stops the timer. The clock-out frequency
depends on the system frequency and the reload value of Timer 2 capture registers (RCAP2H,
RCAP2L), as shown in the following equation.
System Frequency
Clock Out Frequency = ------------------------------------------------------------------------------------------2 × [ 65536 – ( RCAP2H,RCAP2L ) ]
In the frequency generator mode, Timer 2 roll-overs will not generate an interrupt. This behavior
is similar to when Timer 2 is used as a baud-rate generator. It is possible to use Timer 2 as a
baud-rate generator and a clock generator simultaneously. Note, however, that the baud-rate
and clock-out frequencies cannot be determined independently from one another since they
both use RCAP2H and RCAP2L.
Figure 12-7. Timer 2 in Clock-out Mode
OSC
÷CDV
TL2
TH2
RCAP2L
RCAP2H
TR2
C/T2
÷2
T2 PIN
T2EX PIN
EXF2
TRANSITION
DETECTOR
56
T2OE
TIMER 2
INTERRUPT
EXEN2
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
13. External Interrupts
The INT0 (P3.2) and INT1 (P3.3) pins of the AT89LP51/52 may be used as external interrupt
sources. The external interrupts can be programmed to be level-activated or transition-activated
by setting or clearing bit IT1 or IT0 in Register TCON. If ITx = 0, external interrupt x is triggered
by a detected low at the INTx pin. If ITx = 1, external interrupt x is edge-triggered. In this mode if
successive samples of the INTx pin show a high in one cycle and a low in the next cycle, interrupt request flag IEx in TCON is set. Flag bit IEx then requests the interrupt. Since the external
interrupt pins are sampled once each clock cycle, an input high or low should hold for at least 2
system periods to ensure sampling. If the external interrupt is transition-activated, the external
source has to hold the request pin high for at least two clock cycles, and then hold it low for at
least two clock cycles to ensure that the transition is seen so that interrupt request flag IEx will
be set. IEx will be automatically cleared by the CPU when the service routine is called if generated in edge-triggered mode. If the external interrupt is level-activated, the external source has
to hold the request active until the requested interrupt is actually generated. Then the external
source must deactivate the request before the interrupt service routine is completed, or else
another interrupt will be generated. Both INT0 and INT1 may wake up the device from the
Power-down state.
14. Serial Interface (UART)
The serial interface on the AT89LP51/52 implements a Universal Asynchronous
Receiver/Transmitter (UART). The UART has the following features:
• Full-duplex Operation
• 8 or 9 Data Bits
• Framing Error Detection
• Multiprocessor Communication Mode with Automatic Address Recognition
• Baud Rate Generator Using Timer 1 or Timer 2
• Interrupt on Receive Buffer Full or Transmission Complete
• Synchronous SPI or TWI Master Emulation
The serial interface is full-duplex, which means it can transmit and receive simultaneously. It is
also receive-buffered, which means it can begin receiving a second byte before a previously
received byte has been read from the receive register. (However, if the first byte still has not
been read when reception of the second byte is complete, one of the bytes will be lost.) The
serial port receive and transmit registers are both accessed at the Special Function Register
SBUF. Writing to SBUF loads the transmit register, and reading SBUF accesses a physically
separate receive register. The serial port can operate in the following four modes.
• Mode 0: Serial data enters and exits through RXD. TXD outputs the shift clock. Eight data
bits are transmitted/received, with the LSB first. The baud rate is programmable to 1/6 or 1/3
the system frequency in Compatibility mode, 1/4 or 1/2 the system frequency in Fast mode,
or variable based on Time 1.
• Mode 1: 10 bits are transmitted (through TXD) or received (through RXD): a start bit (0),
8 data bits (LSB first), and a stop bit (1). On receive, the stop bit goes into RB8 in the Special
Function Register SCON. The baud rate is variable based on Timer 1 or Timer 2.
• Mode 2: 11 bits are transmitted (through TXD) or received (through RXD): a start bit (0),
8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1). On transmit, the 9th
data bit (TB8 in SCON) can be assigned the value of “0” or “1”. For example, the parity bit
(P, in the PSW) can be moved into TB8. On receive, the 9th data bit goes into RB8 in the
57
3709D–MICRO–12/11
Special Function Register SCON, while the stop bit is ignored. The baud rate is
programmable to either 1/16 or 1/32 the system frequency.
• Mode 3: 11 bits are transmitted (through TXD) or received (through RXD): a start bit (0),
8 data bits (LSB first), a programmable 9th data bit, and a stop bit (1). In fact, Mode 3 is the
same as Mode 2 in all respects except the baud rate, which is variable based on Timer 1 or
Timer 2 in Mode 3.
In all four modes, transmission is initiated by any instruction that uses SBUF as a destination
register. Reception is initiated in Mode 0 by the condition RI = 0 and REN = 1. Reception is initiated in the other modes by the incoming start bit if REN = 1.
Table 14-1.
SCON – Serial Port Control Register
SCON Address = 98H
Reset Value = 0000 0000B
Bit Addressable
SM0/FE
Bit
7
(SMOD0 = 0/1)
SM1
SM2
REN
TB8
RB8
T1
RI
6
5
4
3
2
1
0
(1)
Symbol
Function
FE
Framing error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid
frames and must be cleared by software. The SMOD0 bit must be set to enable access to the FE bit. FE will be set
regardless of the state of SMOD0.
SM0
Serial Port Mode Bit 0, (SMOD0 must = 0 to access bit SM0)
Serial Port Mode Bit 1
SM1
SM0
SM1
Mode
Description
Baud Rate (Compat.)(2)
Baud Rate (Fast)(2)
0
0
0
shift register
fSYS/3 or fSYS/6 or Timer 1
fSYS/2 or fSYS/4 or Timer 1
0
1
1
8-bit UART
variable (Timer 1 or Timer 2)
variable (Timer 1 or Timer 2)
1
0
2
9-bit UART
fSYS/32 or fSYS/16
fSYS/32 or fSYS/16
1
1
3
9-bit UART
variable (Timer 1 or Timer 2)
variable (Timer 1 or Timer 2)
SM2
Enables the Automatic Address Recognition feature in Modes 2 or 3. If SM2 = 1 then Rl will not be set unless the received
9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address. In Mode 1, if SM2 =
1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a Given or Broadcast Address.
In Mode 0, SM2 determines the idle state of the shift clock such that the clock is the inverse of SM2, i.e. when SM2 = 0
the clock idles high and when SM2 = 1 the clock idles low.
REN
Enables serial reception. Set by software to enable reception. Clear by software to disable reception.
TB8
The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired. In Mode 0, setting TB8
enables Timer 1 as the shift clock generator.
RB8
In Modes 2 and 3, the 9th data bit that was received. In Mode 1, if SM2 = 0, RB8 is the stop bit that was received. In Mode
0, RB8 is not used.
TI
Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the beginning of the stop bit in the
other modes, in any serial transmission. Must be cleared by software.
RI
Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or halfway through the stop bit time in the
other modes, in any serial reception (except see SM2). Must be cleared by software.
Notes:
58
1. SMOD0 is located at PCON.6.
2. fSYS = system frequency. The baud rate depends on SMOD1 (PCON.7).
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
14.1
Multiprocessor Communications
Modes 2 and 3 have a special provision for multiprocessor communications. In these modes,
9 data bits are received, followed by a stop bit. The 9th bit goes into RB8. Then comes a stop bit.
The port can be programmed such that when the stop bit is received, the serial port interrupt is
activated only if RB8 = 1. This feature is enabled by setting bit SM2 in SCON.
The following example shows how to use the serial interrupt for multiprocessor communications.
When the master processor must transmit a block of data to one of several slaves, it first sends
out an address byte that identifies the target slave. An address byte differs from a data byte in
that the 9th bit is “1” in an address byte and “0” in a data byte. With SM2 = 1, no slave is
interrupted by a data byte. An address byte, however, interrupts all slaves. Each slave can
examine the received byte and see if it is being addressed. The addressed slave clears its SM2
bit and prepares to receive the data bytes that follows. The slaves that are not addressed set
their SM2 bits and ignore the data bytes. See “Automatic Address Recognition” on page 61.
The SM2 bit can be used to check the validity of the stop bit in Mode 1. In a Mode 1 reception, if
SM2 = 1, the receive interrupt is not activated unless a valid stop bit is received.
14.2
Baud Rates
The baud rate in Mode 0 depends on the value of the SMOD1 bit in Special Function Register
PCON.7. If SMOD1 = 0 (the value on reset) and TB8 = 0, the baud rate is 1/4 of the system frequency in Fast mode. If SMOD1 = 1 and TB8 = 0, the baud rate is 1/2 of the system frequency,
as shown in the following equation:
Mode 0 Baud Rate
TB8 = 0
SMOD1
2
= -------------------- × System Frequency
4
:In Compatibility mode the baud rate is 1/6 of the system frequency, scaling to 1/3 when
SMOD1 = 1.
Mode 0 Baud Rate
TB8 = 0
SMOD1
2
= -------------------- × System Frequency
6
The baud rate in Mode 2 also depends on the value of the SMOD1 bit. If SMOD1 = 0, the baud
rate is 1/32 of the system frequency. If SMOD1 = 1, the baud rate is 1/16 of the system frequency, as shown in the following equation:
SMOD1
2
Mode 2 Baud Rate = -------------------- × System Frequency
32
14.2.1
Using Timer 1 to Generate Baud Rates
Setting TB8 = 1 in Mode 0 enables Timer 1 as the baud rate generator. When Timer 1 is the
baud rate generator for Mode 0, the baud rates are determined by the Timer 1 overflow rate and
the value of SMOD1 according to the following equation:
Mode 0 Baud Rate
TB8 = 1
SMOD1
2
= -------------------- × (Timer 1 Overflow Rate)
4
59
3709D–MICRO–12/11
The Timer 1 overflow rate normally determines the baud rates in Modes 1 and 3. When Timer 1
is the baud rate generator, the baud rates are determined by the Timer 1 overflow rate and the
value of SMOD1 according to the following equation:
Modes 1, 3
SMOD1
2
= -------------------- × (Timer 1 Overflow Rate)
32
Baud Rate
The Timer 1 interrupt should be disabled in this application. The Timer itself can be configured
for either timer or counter operation in any of its 3 running modes. In the most typical applications, it is configured for timer operation in auto-reload mode (high nibble of TMOD = 0010B). In
this case, the baud rate is given by the following formula:
Modes 1, 3
SMOD1
2
System Frequency
1
= -------------------- × -------------------------------------------------- × --------------------32
[ 256 – ( TH1 ) ]
TPS + 1
Baud Rate
Table 14-2 lists commonly used baud rates and how they can be obtained from Timer 1.
Table 14-2.
Commonly Used Baud Rates Generated by Timer 1
Timer 1
Baud Rate
fOSC (MHz)
CDV
SMOD1
C/T
Mode
TPS
Reload Value
Mode 0 Max: 6 MHz
12
0
1
X
X
0
X
Mode 2 Max: 750K
12
0
1
X
X
0
X
Modes 1, 3 Max: 750K
12
0
1
0
2
0
F4H
19.2K
11.059
0
1
0
2
0
DCH
9.6K
11.059
0
0
0
2
0
DCH
4.8K
11.059
0
0
0
2
0
B8H
2.4K
11.059
0
0
0
2
0
70H
1.2K
11.059
0
0
0
1
0
FEE0H
137.5
11.986
0
0
0
1
0
F55CH
110
6
0
1
0
1
0
F2AFH
110
12
0
0
0
1
0
F2AFH
19.2K
11.059
1
1
0
2
5
FDH
9.6K
11.059
1
0
0
2
5
FDH
4.8K
11.059
1
0
0
2
5
FAH
2.4K
11.059
1
0
0
2
5
F4H
1.2K
11.059
1
0
0
2
5
E8H
137.5
11.986
1
0
0
2
5
1DH
110
6
1
0
0
2
5
72H
110
12
1
0
0
1
5
FEEBH
14.2.2
60
Using Timer 2 to Generate Baud Rates
Timer 2 is selected as the baud rate generator by setting TCLK and/or RCLK in T2CON. Under
these conditions, the baud rates for transmit and receive can be simultaneously different by
using Timer 1 for transmit and Timer 2 for receive, or vice versa. The baud rate generator mode
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
is similar to the auto-reload mode, in that a rollover causes the Timer 2 registers to be reloaded
with the 16-bit value in registers RCAP2H and RCAP2L, which are preset by software. In this
case, the baud rates in Modes 1 and 3 are determined by Timer 2’s overflow rate according to
the following equation:
Modes 1 and 3
Baud Rate
1
System Frequency
= ------ × --------------------------------------------------------------------------------16 [ 65536 – ( RCAP2H,RCAP2L ) ]
Table 14-3 lists commonly used baud rates and how they can be obtained from Timer 2.
Table 14-3.
Commonly Used Baud Rates Generated by Timer 2
Timer 2
14.3
Baud Rate
fOSC (MHz)
CDV
CP/RL2
C/T2
TCLK or RCLK
Reload Value
Max: 750K
12
0
0
0
1
FFFFH
19.2K
11.059
0
0
0
1
FFDCH
9.6K
11.059
0
0
0
1
FFB8H
4.8K
11.059
0
0
0
1
FF70H
2.4K
11.059
0
0
0
1
FEE0H
1.2K
11.059
0
0
0
1
FDC0H
137.5
11.986
0
0
0
1
EAB8H
110
6
0
0
0
1
F2AFH
110
12
0
0
0
1
E55EH
19.2K
11.059
1
0
0
1
FFEEH
9.6K
11.059
1
0
0
1
FFDCH
4.8K
11.059
1
0
0
1
FFB8H
2.4K
11.059
1
0
0
1
FF70H
1.2K
11.059
1
0
0
1
FEE0H
137.5
11.986
1
0
0
1
F55CH
110
12
1
0
0
1
F2AFH
Framing Error Detection
In addition to all of its usual modes, the UART can perform framing error detection by looking for
missing stop bits, and automatic address recognition. When used for framing error detect, the
UART looks for missing stop bits in the communication. A missing bit will set the FE bit in the
SCON register. The FE bit shares the SCON.7 bit with SM0 and the function of SCON.7 is determined by PCON.6 (SMOD0). If SMOD0 is set then SCON.7 functions as FE. SCON.7 functions
as SM0 when SMOD0 is cleared. When used as FE, SCON.7 can only be cleared by software.
The FE bit will be set by a framing error regardless of the state of SMOD0.
14.4
Automatic Address Recognition
Automatic Address Recognition is a feature which allows the UART to recognize certain
addresses in the serial bit stream by using hardware to make the comparisons. This feature
saves a great deal of software overhead by eliminating the need for the software to examine
every serial address which passes by the serial port. This feature is enabled by setting the SM2
bit in SCON for Modes 1, 2 or 3. In the 9-bit UART modes, Mode 2 and Mode 3, the Receive
61
3709D–MICRO–12/11
Interrupt flag (RI) will be automatically set when the received byte contains either the “Given”
address or the “Broadcast” address. The 9-bit mode requires that the 9th information bit be a “1”
to indicate that the received information is an address and not data.
In Mode 1 (8-bit) the RI flag will be set if SM2 is enabled and the information received has a valid
stop bit following the 8th address bits and the information is either a Given or Broadcast
address. Automatic Address Recognition is not available during Mode 0.
Using the Automatic Address Recognition feature allows a master to selectively communicate
with one or more slaves by invoking the given slave address or addresses. All of the slaves may
be contacted by using the Broadcast address. Two special Function Registers are used to
define the slave’s address, SADDR, and the address mask, SADEN. SADEN is used to define
which bits in the SADDR are to be used and which bits are “don’t care”. The SADEN mask can
be logically ANDed with the SADDR to create the “Given” address which the master will use for
addressing each of the slaves. Use of the Given address allows multiple slaves to be recognized
while excluding others. The following examples show the versatility of this scheme:
Slave 0
SADDR = 1100 0000
SADEN = 1111 1101
Given = 1100 00X0
Slave 1
SADDR = 1100 0000
SADEN = 1111 1110
Given = 1100 000X
In the previous example, SADDR is the same and the SADEN data is used to differentiate
between the two slaves. Slave 0 requires a “0” in bit 0 and it ignores bit 1. Slave 1 requires a “0”
in bit 1 and bit 0 is ignored. A unique address for slave 0 would be 1100 0010 since slave 1
requires a “0” in bit 1. A unique address for slave 1 would be 1100 0001 since a “1” in bit 0 will
exclude slave 0. Both slaves can be selected at the same time by an address which has bit 0 = 0
(for slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed with 1100 0000.
In a more complex system, the following could be used to select slaves 1 and 2 while excluding
slave 0:
Slave 0
SADDR = 1100 0000
SADEN = 1111 1001
Given = 1100 0XX0
Slave 1
SADDR = 1110 0000
SADEN = 1111 1010
Given = 1110 0X0X
Slave 2
SADDR = 1110 0000
SADEN = 1111 1100
Given = 1110 00XX
In the above example, the differentiation among the 3 slaves is in the lower 3 address bits. Slave
0 requires that bit 0 = 0 and it can be uniquely addressed by 1110 0110. Slave 1 requires that
bit 1 = 0 and it can be uniquely addressed by 1110 and 0101. Slave 2 requires that bit 2 = 0 and
its unique address is 1110 0011. To select Slaves 0 and 1 and exclude Slave 2, use address
1110 0100, since it is necessary to make bit 2 = 1 to exclude slave 2.
62
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
The Broadcast Address for each slave is created by taking the logic OR of SADDR and SADEN.
Zeros in this result are trended as don’t cares. In most cases, interpreting the don’t cares as
ones, the broadcast address will be FF hexadecimal.
Upon reset SADDR (SFR address 0A9H) and SADEN (SFR address 0B9H) are loaded with
“0”s. This produces a given address of all “don’t cares” as well as a Broadcast address of all
“don’t cares”. This effectively disables the Automatic Addressing mode and allows the microcontroller to use standard 80C51-type UART drivers which do not make use of this feature.
14.5
More About Mode 0
In Mode 0, the UART is configured as either a two wire half-duplex or three wire full-duplex synchronous serial interface. In two-wire mode serial data enters and exits through RXD and TXD
outputs the shift clock. In three-wire mode serial data enters through MISO, exits through MOSI
and SCK outputs the shift clock. Eight data bits are transmitted/received, with the LSB first. Figure 14-3 and Figure 14-5 on page 67 show simplified functional diagrams of the serial port in
Mode 0 and associated timing. The baud rate is programmable to 1/2 or 1/4 the system frequency by setting/clearing the SMOD1 bit in Fast mode, or 1/3 or 1/6 the system frequency in
Compatibility mode. However, changing SMOD1 has an effect on the relationship between the
clock and data as described below. The baud rate can also be generated by Timer 1 by setting
TB8. Table 14-4 lists the baud rate options for Mode 0.
Table 14-4.
14.5.1
Mode 0 Baud Rates
TB8
SMOD1
Baud Rate (Fast)
Baud Rate (Compatibility)
0
0
fSYS/4
fSYS/6
0
1
fSYS/2
fSYS/3
1
0
(Timer 1 Overflow) / 4
(Timer 1 Overflow) / 4
1
1
(Timer 1 Overflow) / 2
(Timer 1 Overflow) / 2
Two-Wire (Half-Duplex) Mode
Transmission is initiated by any instruction that uses SBUF as a destination register. The “write
to SBUF” signal also loads a “1” into the 9th position of the transmit shift register and tells the TX
Control Block to begin a transmission. The internal timing is such that one full bit slot may elapse
between “write to SBUF” and activation of SEND.
SEND transfers the output of the shift register to the alternate output function line of P3.0, and
also transfers Shift Clock to the alternate output function line of P3.1. As data bits shift out to the
right, “0”s come in from the left. When the MSB of the data byte is at the output position of the
shift register, the “1” that was initially loaded into the 9th position is just to the left of the MSB,
and all positions to the left of that contain “0”s. This condition flags the TX Control block to do
one last shift, then deactivate SEND and set TI.
Reception is initiated by the condition REN = 1 and RI = 0. At the next clock cycle, the RX Control unit writes the bits 11111110B to the receive shift register and activates RECEIVE in the
next clock phase. RECEIVE enables Shift Clock to the alternate output function line of P3.1. As
data bits come in from the right, “1”s shift out to the left. When the “0” that was initially loaded
into the right-most position arrives at the left-most position in the shift register, it flags the RX
Control block to do one last shift and load SBUF. Then RECEIVE is cleared and RI is set.
The relationship between the shift clock and data is determined by the combination of the SM2
and SMOD1 bits as listed in Table 14-5 and shown in Figure . The SM2 bit determines the idle
63
3709D–MICRO–12/11
state of the clock when not currently transmitting/receiving. The SMOD1 bit determines if the
output data is stable for both edges of the clock, or just one.
Table 14-5.
Mode 0 Clock and Data Modes
SM2
SMOD1
Clock Idle
Data Changes
Data Sampled
0
0
High
While clock is high
Positive edge of clock
0
1
High
Negative edge of clock
Positive edge of clock
1
0
Low
While clock is low
Negative edge of clock
1
1
Low
Negative edge of clock
Positive edge of clock
In Two-Wire configuration Mode 0 may be used as a hardware accelerator for software emulation of serial interfaces such as a half-duplex Serial Peripheral Interface (SPI) master in mode
(0,0) or (1,1) or a Two-Wire Interface (TWI) in master mode. An example of Mode 0 emulating a
TWI master device is shown in Figure 14-2. In this example, the start, stop, and acknowledge
are handled in software while the byte transmission is done in hardware. Falling/rising edges on
TXD are created by setting/clearing SM2. Rising/falling edges on RXD are forced by setting/clearing the P3.0 register bit. SM2 and P3.0 must be 1 while the byte is being transferred.
Figure 14-1. Mode 0 Waveforms (Two-Wire)
SMOD1 = 0
SM2 = 0
TXD
RXD (TX)
0
0
RXD (RX)
SMOD1 = 1
SM2 = 0
1
0
2
1
0
RXD (RX)
4
3
5
4
6
5
7
6
7
2
1
3
2
4
3
5
4
6
5
7
6
7
TXD
RXD (TX)
0
1
0
RXD (RX)
SMOD1 = 1
SM2 = 1
1
3
TXD
RXD (TX)
SMOD1 = 0
SM2 = 1
2
2
1
3
2
4
3
5
4
6
5
7
6
7
TXD
0
RXD (TX)
1
0
RXD (RX)
2
1
3
2
4
3
5
4
6
5
6
7
7
Figure 14-2. UART Mode 0 TWI Emulation (SMOD1 = 1)
(SCL) TXD
(SDA) RXD
0
1
2
3
4
5
6
7
ACK
SM2
P3.0
Sample ACK
Write to SBUF
TI
64
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 14-3. Serial Port Mode 0 (Two-Wire)
INTERNAL BUS
TIMER 1
OVERFLOW
1
“1“
f sys
0
TB8
÷2
÷2
0
1
SMOD1
SM2
INTERNAL BUS
WRITE TO SBUF
SEND
SHIFT
RXD (DATA OUT)
TXD (SHIFT CLOCK)
TI
WRITE TO SCON (CLEAR RI)
RI
RECEIVE
SHIFT
RXD (DATA IN)
TXD (SHIFT CLOCK)
65
3709D–MICRO–12/11
Mode 0 transfers data LSB first whereas SPI or TWI are generally MSB first. Emulation of these
interfaces may require bit reversal of the transferred data bytes. The following code example
reverses the bits in the accumulator:
EX:
MOV
REVRS: RLC
XCH
RRC
XCH
DJNZ
14.5.2
R7, #8
A
A, R6
A
A, R6
R7, REVRS
; C << msb (ACC)
; msb (ACC) >> B
Three-Wire (Full-Duplex) Mode
Three-Wire Mode is similar to Two-Wire except that the shift data input and data output are separated for full-duplex operation. Three-Wire Mode is enabled by setting the SPEN bit in TCONB.
Transmission is initiated by any instruction that uses SBUF as a destination register. The “write
to SBUF” signal also loads a “1” into the 9th position of the transmit shift register and tells the TX
Control Block to begin a transmission. The internal timing is such that one full bit slot may elapse
between “write to SBUF” and activation of SEND.
SEND transfers the output of the shift register to the alternate output function line of P1.5, and
also transfers Shift Clock to the alternate output function line of P1.7. As data bits shift out to the
right, “0”s come in from the left. When the MSB of the data byte is at the output position of the
shift register, the “1” that was initially loaded into the 9th position is just to the left of the MSB,
and all positions to the left of that contain “0”s. This condition flags the TX Control block to do
one last shift, then deactivate SEND and set TI.
Reception occurs simultaneously with transmission if REN = 1. Data is input from P1.6. When
REN = 1 any write to SBUF causes the RX Control unit to write the bits 11111110B to the
receive shift register and activates RECEIVE in the next clock phase. As data bits come in from
the right, “1”s shift out to the left. When the “0” that was initially loaded into the right-most position arrives at the left-most position in the shift register, it flags the RX Control block to do one
last shift and load SBUF. Then RECEIVE is cleared and RI is set. When REN = 0, the receiver is
not enabled. When a transmission occurs, SBUF will not be updated and RI will not be set even
though serial data is received on P1.6.
The relationship between the shift clock and data is identical to Two-Wire mode as listed in
Table 14-5 and shown in Figure . Three-Wire mode uses different I/Os from Two-Wire mode and
can be connected to SPI slave devices as shownin Figure 14-4. It is possible to time share the
UART hardware between SPI devices connected on P1 and UART devices on P3 with the
caveat that any asynchronous receptions on the RXD pin will be ignored while the UART is in
Mode 0.
Figure 14-4. SPI Connections for UART Mode 0
Master
MSB
LSB
MSB
MISO
Slave
LSB
MISO
8-Bit Shift Register
8-Bit Shift Register
MOSI
AT89LP52
MOSI
SS
GPIO
Clock
Generator
66
SCK
SCK
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 14-5. Serial Port Mode 0 (Three-Wire)
INTERNAL BUS
TIMER 1
OVERFLOW
“1“
f sys
1
0
MOSI
P1.5 ALT
OUTPUT
FUNCTION
TB8
÷2
÷2
0
1
SMOD1
TI
SERIAL
PORT
INTERRUPT
SCK
P1.7 ALT
OUTPUT
FUNCTION
SM2
MISO
P1.6 ALT
OUTPUT
FUNCTION
INTERNAL BUS
WRITE TO SBUF
SEND
SHIFT
MOSI (DATA OUT)
SCK (SHIFT CLOCK)
MISO (DATA IN)
TI
RI
67
3709D–MICRO–12/11
14.6
More About Mode 1
Ten bits are transmitted (through TXD), or received (through RXD): a start bit (0), 8 data bits
(LSB first), and a stop bit (1). On receive, the stop bit goes into RB8 in SCON. In the
AT89LP51/52, the baud rate is determined either by the Timer 1 overflow rate, the TImer 2 overflow rate, or both. In this case one timer is for transmit and the other is for receive. Figure 14-6
shows a simplified functional diagram of the serial port in Mode 1 and associated timings for
transmit and receive.
Transmission is initiated by any instruction that uses SBUF as a destination register. The “write
to SBUF” signal also loads a “1” into the 9th bit position of the transmit shift register and flags the
TX Control unit that a transmission is requested. Transmission actually commences at S1P1 of
the machine cycle following the next rollover in the divide-by-16 counter. Thus, the bit times are
synchronized to the divide-by-16 counter, not to the “write to SBUF” signal.
The transmission begins when SEND is activated, which puts the start bit at TXD. One bit time
later, DATA is activated, which enables the output bit of the transmit shift register to TXD. The
first shift pulse occurs one bit time after that.
As data bits shift out to the right, “0”s are clocked in from the left. When the MSB of the data byte
is at the output position of the shift register, the “1” that was initially loaded into the 9th position is
just to the left of the MSB, and all positions to the left of that contain “0”s. This condition flags the
TX Control unit to do one last shift, then deactivate SEND and set TI. This occurs at the tenth
divide-by-16 rollover after “write to SBUF.”
Reception is initiated by a 1-to-0 transition detected at RXD. For this purpose, RXD is sampled
at a rate of 16 times the established baud rate. When a transition is detected, the divide-by-16
counter is immediately reset, and 1FFH is written into the input shift register. Resetting the
divide-by-16 counter aligns its roll-overs with the boundaries of the incoming bit times.
The 16 states of the counter divide each bit time into 16ths. At the 7th, 8th, and 9th counter
states of each bit time, the bit detector samples the value of RXD. The value accepted is the
value that was seen in at least 2 of the 3 samples. This is done to reject noise. In order to reject
false bits, if the value accepted during the first bit time is not 0, the receive circuits are reset and
the unit continues looking for another 1-to-0 transition. If the start bit is valid, it is shifted into the
input shift register, and reception of the rest of the frame proceeds.
As data bits come in from the right, “1”s shift out to the left. When the start bit arrives at the leftmost position in the shift register, (which is a 9-bit register in Mode 1), it flags the RX Control
block to do one last shift, load SBUF and RB8, and set RI. The signal to load SBUF and RB8
and to set RI is generated if, and only if, the following conditions are met at the time the final shift
pulse is generated.
RI = 0 and
Either SM2 = 0, or the received stop bit = 1
If either of these two conditions is not met, the received frame is irretrievably lost. If both conditions are met, the stop bit goes into RB8, the 8 data bits go into SBUF, and RI is activated. At
this time, whether or not the above conditions are met, the unit continues looking for a 1-to-0
transition in RXD.
68
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 14-6. Serial Port Mode 1
TIMER 2
OVERFLOW
TIMER 1
OVERFLOW
INTERNAL BUS
“1”
WRITE
TO
SBUF
÷2
S
D Q
CL
“1”
“0”
SBUF
SMOD1
TXD
ZERO DETECTOR
“0”
“1”
SHIFT DATA
START
TX CONTROL
TCLK
÷16
SEND
TI
SERIAL
PORT
INTERRUPT
“1”
“0”
RX CLOCK
RCLK
÷16
SAMPLE
1-TO-0
TRANSITION
DETECTOR
RX CLOCK RI
START
RX CONTROL
LOAD
SBUF
SHIFT
1FFH
BIT
DETECTOR
INPUT SHIFT REG.
(9 BITS)
RXD
SHIFT
LOAD
SBUF
SBUF
READ
SBUF
INTERNAL BUS
TRANSMIT
TX
CLOCK
WRITE TO SBUF
SEND
DATA
SHIFT
D0
TXD
TI
RX
CLOCK
RECEIVE
D1
D2
D3
D4
D5
D6
D7
STOP BIT
START BIT
RXD
÷16 RESET
START BIT
D0
D1
D2
D3
D4
D5
D6
D7
STOP BIT
BIT DETECTOR SAMPLE TIMES
SHIFT
RI
69
3709D–MICRO–12/11
14.7
More About Modes 2 and 3
Eleven bits are transmitted (through TXD), or received (through RXD): a start bit (0), 8 data bits
(LSB first), a programmable 9th data bit, and a stop bit (1). On transmit, the 9th data bit (TB8)
can be assigned the value of “0” or “1”. On receive, the 9th data bit goes into RB8 in SCON. The
baud rate is programmable to either 1/16 or 1/32 of the oscillator frequency in Mode 2. Mode 3
may have a variable baud rate generated from either Timer 1 or Timer 2, depending on the state
of RCLK and TCLK.
Figures 14-7 and 14-8 show a functional diagram of the serial port in Modes 2 and 3. The
receive portion is exactly the same as in Mode 1. The transmit portion differs from Mode 1 only
in the 9th bit of the transmit shift register.
Transmission is initiated by any instruction that uses SBUF as a destination register. The “write
to SBUF” signal also loads TB8 into the 9th bit position of the transmit shift register and flags the
TX Control unit that a transmission is requested. Transmission commences at S1P1 of the
machine cycle following the next rollover in the divide-by-16 counter. Thus, the bit times are synchronized to the divide-by-16 counter, not to the “write to SBUF” signal.
The transmission begins when SEND is activated, which puts the start bit at TXD. One bit time
later, DATA is activated, which enables the output bit of the transmit shift register to TXD. The
first shift pulse occurs one bit time after that. The first shift clocks a “1” (the stop bit) into the 9th
bit position of the shift register. Thereafter, only “0”s are clocked in. Thus, as data bits shift out to
the right, “0”s are clocked in from the left. When TB8 is at the output position of the shift register,
then the stop bit is just to the left of TB8, and all positions to the left of that contain “0”s. This condition flags the TX Control unit to do one last shift, then deactivate SEND and set TI. This occurs
at the 11th divide-by-16 rollover after “write to SBUF.”
Reception is initiated by a 1-to-0 transition detected at RXD. For this purpose, RXD is sampled
at a rate of 16 times the established baud rate. When a transition is detected, the divide-by-16
counter is immediately reset, and 1FFH is written to the input shift register.
At the 7th, 8th and 9th counter states of each bit time, the bit detector samples the value of RXD.
The value accepted is the value that was seen in at least 2 of the 3 samples. If the value
accepted during the first bit time is not 0, the receive circuits are reset and the unit continues
looking for another 1-to-0 transition. If the start bit proves valid, it is shifted into the input shift
register, and reception of the rest of the frame proceeds.
As data bits come in from the right, “1”s shift out to the left. When the start bit arrives at the leftmost position in the shift register (which in Modes 2 and 3 is a 9-bit register), it flags the RX Control block to do one last shift, load SBUF and RB8, and set RI. The signal to load SBUF and RB8
and to set RI is generated if, and only if, the following conditions are met at the time the final shift
pulse is generated:
RI = 0, and
Either SM2 = 0 or the received 9th data bit = 1
If either of these conditions is not met, the received frame is irretrievably lost, and RI is not set. If
both conditions are met, the received 9th data bit goes into RB8, and the first 8 data bits go into
SBUF. One bit time later, whether the above conditions were met or not, the unit continues looking for a 1-to-0 transition at the RXD input.
Note that the value of the received stop bit is irrelevant to SBUF, RB8, or RI.
70
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 14-7. Serial Port Mode 2
INTERNAL BUS
CPU CLOCK
SMOD1 1
SMOD1 0
INTERNAL BUS
71
3709D–MICRO–12/11
Figure 14-8. Serial Port Mode 3
TIMER 2
OVERFLOW
TIMER 1
OVERFLOW
INTERNAL BUS
TB8
WRITE
TO
SBUF
÷2
“0”
S
D Q
CL
“1”
SMOD1
SBUF
TXD
ZERO DETECTOR
“0”
“1”
TCLK
÷16
“0”
SHIFT DATA
START STOP BIT
TX CONTROL
RX CLOCK
SEND
TI
SERIAL
PORT
INTERRUPT
“1”
RCLK
÷16
SAMPLE
1-TO-0
TRANSITION
DETECTOR
RX CLOCK RI
START
RX CONTROL
LOAD
SBUF
SHIFT
1FFH
BIT
DETECTOR
INPUT SHIFT REG.
(9 BITS)
RXD
SHIFT
LOAD
SBUF
SBUF
READ
SBUF
INTERNAL BUS
TRANSMIT
TX
CLOCK
WRITE TO SBUF
SEND
DATA
SHIFT
D0
TXD
TI
D1
D2
D3
D4
D5
D6
D7
TB8
START BIT
STOP BIT
RECEIVE
STOP BIT GEN
RX
CLOCK
÷16 RESET
RXD
START BIT
BIT DETECTOR SAMPLE TIMES
D0
D1
D2
D3
D4
D5
D6
D7
RB8
STOP
BIT
SHIFT
RI
72
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
15. Programmable Watchdog Timer
The programmable Watchdog Timer (WDT) protects the system from incorrect execution by triggering a system reset when it times out after the software has failed to feed the timer prior to the
timer overflow. By Default the WDT counts CPU clock cycles. The prescaler bits, PS0, PS1 and
PS2 in SFR WDTCON are used to set the period of the Watchdog Timer from 16K to 2048K
clock cycles. The Timer Prescaler can also be used to lengthen the time-out period (see Table
6-2 on page 31) The WDT is disabled by Reset and during Power-down mode. When the WDT
times out without being serviced, an internal RST pulse is generated to reset the CPU. See
Table 15-1 for the available WDT period selections.
Table 15-1.
Watchdog Timer Time-out Period Selection
WDT Prescaler Bits
Note:
PS2
PS1
PS0
Period(1)
(Clock Cycles)
0
0
0
16K
0
0
1
32K
0
1
0
64K
0
1
1
128K
1
0
0
256K
1
0
1
512K
1
1
0
1024K
1
1
1
2048K
1. The WDT time-out period is dependent on the system clock frequency.
( PS + 14 )
2
Time-out Period = -------------------------------------------------- × ( TPS + 1 )
System Frequency
The Watchdog Timer consists of a 14-bit timer with 7-bit programmable prescaler. Writing the
sequence 1EH/E1H to the WDTRST register enables the timer. When the WDT is enabled, the
WDTEN bit in WDTCON will be set to “1”. To prevent the WDT from generating a reset when if
overflows, the watchdog feed sequence must be written to WDTRST before the end of the timeout period. To feed the watchdog, two write instructions must be sequentially executed successfully. Between the two write instructions, SFR reads are allowed, but writes are not allowed. The
instructions should move 1EH to the WDTRST register and then 1EH to the WDTRST register.
An incorrect feed or enable sequence will cause an immediate watchdog reset. The program
sequence to feed or enable the watchdog timer is as follows:
MOV WDTRST, #01Eh
MOV WDTRST, #0E1h
15.1
Software Reset
A Software Reset of the AT89LP51/52 is accomplished by writing the software reset sequence
5AH/A5H to the WDTRST SFR. The WDT does not need to be enabled to generate the software
reset. A normal software reset will set the SWRST flag in WDTCON. However, if at any time an
incorrect sequence is written to WDTRST (i.e. anything other than 1EH/E1H or 5AH/A5H), a
software reset will immediately be generated and both the SWRST and WDTOVF flags will be
set. In this manner an intentional software reset may be distinguished from a software error-generated reset. The program sequence to generate a software reset is as follows:
73
3709D–MICRO–12/11
MOV WDTRST, #05Ah
MOV WDTRST, #0A5h
Table 15-2.
WDTCON – Watchdog Control Register
WDTCON Address = A7H
Reset Value = 0000 0XX0B
Not Bit Addressable
PS2
PS1
PS0
WDIDLE(1)
DISRTO(1)
SWRST
WDTOVF
WDTEN
7
6
5
4
3
2
1
0
Bit
Symbol
Function
PS2
PS1
PS0
Prescaler bits for the watchdog timer (WDT). When all three bits are cleared to 0, the watchdog timer has a nominal
period of 16K clock cycles. When all three bits are set to 1, the nominal period is 2048K clock cycles.
WDIDLE
WDT Disable during Idle(1). When WDIDLE = 0 the WDT continues to count in Idle mode. When WDIDLE = 1 the WDT
halts counting in Idle mode.
DISRTO
Disable Reset Output(1). When DISTRO = 0 the reset pin is driven to the same level as POL when the WDT resets.
When DISRTO = 1 the reset pin is input only.
SWRST
Software Reset Flag. Set when a software reset is generated by writing the sequence 5AH/A5H to WDTRST. Also set
when an incorrect sequence is written to WDTRST. Must be cleared by software.
WDTOVF
Watchdog Overflow Flag. Set when a WDT rest is generated by the WDT timer overflow. Also set when an incorrect
sequence is written to WDTRST. Must be cleared by software.
WDTEN
Watchdog Enable Flag. This bit is READ-ONLY and reflects the status of the WDT (whether it is running or not). The
WDT is disabled after any reset and must be re-enabled by writing 1EH/E1H to WDTRST
Note:
1. WDTCON.4 and WDTCON.3 function as WDIDLE and DISRTO only in Fast mode. In Compatibility mode these bits are in
AUXR. (See Table 3-3 on page 20)
Table 15-3.
WDTRST – Watchdog Reset Register
WDTCON Address = A6H
(Write-Only)
Not Bit Addressable
Bit
–
–
–
–
–
–
–
–
7
6
5
4
3
2
1
0
The WDT is enabled by writing the sequence 1EH/E1H to the WDTRST SFR. The current status may be checked by reading
the WDTEN bit in WDTCON. To prevent the WDT from resetting the device, the same sequence 1EH/E1H must be written to
WDTRST before the time-out interval expires. A software reset is generated by writing the sequence 5AH/A5H to WDTRST.
74
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
16. Instruction Set Summary
The AT89LP51/52 is fully binary compatible with the 8051 instruction set. In Compatibility mode
the AT89LP51/52 has identical execution time with AT89S51/52 and other standard 8051s. The
difference between the AT89LP51/52 in Fast mode and the standard 8051 is the number of
cycles required to execute an instruction. Fast mode instructions may take 1 to 5 clock cycles to
complete. The execution times of most instructions may be computed using Table 16-1. Note
that for the purposes of this table, a clock cycle is one period of the output of the system clock
divider. For Fast mode the divider defaults to 1, so the clock cycle equals the oscillator period.
For Compatibility mode the divider defaults to 2, so the clock cycle is twice the oscillator period,
or conversely the clock count is half the number of oscillator periods.
Table 16-1.
Instruction Execution Times and Exceptions(1)
Generic Instruction Types
Fast Mode Cycle Count Formula
Most arithmetic, logical, bit and transfer instructions
# bytes
Branches and Calls
# bytes + 1
Single Byte Indirect (i.e. ADD A, @Ri, etc.)
2
RET, RETI
4
MOVC
3
MOVX
4(3)
MUL
2
DIV
4
INC DPTR
2
Clock Cycles
Arithmetic
Bytes
Compatibility
Fast
Hex Code
ADD A, Rn
1
6
1
28-2F
ADD A, direct
2
6
2
25
ADD A, @Ri
1
6
2
26-27
ADD A, #data
2
6
2
24
ADDC A, Rn
1
6
1
38-3F
ADDC A, direct
2
6
2
35
ADDC A, @Ri
1
6
2
36-37
ADDC A, #data
2
6
2
34
SUBB A, Rn
1
6
1
98-9F
SUBB A, direct
2
6
2
95
SUBB A, @Ri
1
6
2
96-97
SUBB A, #data
2
6
2
94
INC Rn
1
6
1
08-0F
INC direct
2
6
2
05
INC @Ri
1
6
2
06-07
INC A
2
6
2
04
DEC Rn
1
6
1
18-1F
DEC direct
2
6
2
15
75
3709D–MICRO–12/11
Table 16-1.
Instruction Execution Times and Exceptions(1) (Continued)
DEC @Ri
1
6
2
16-17
DEC A
2
6
2
14
INC DPTR
1
12
2
A3
INC /DPTR(2)
2
18
3
A5 A3
MUL AB
1
24
2
A4
DIV AB
1
24
4
84
DA A
1
6
1
D4
Clock Cycles
Logical
Bytes
Compatibility
Fast
Hex Code
CLR A
1
6
1
E4
CPL A
1
6
1
F4
ANL A, Rn
1
6
1
58-5F
ANL A, direct
2
6
2
55
ANL A, @Ri
1
6
2
56-57
ANL A, #data
2
6
2
54
ANL direct, A
2
6
2
52
ANL direct, #data
3
12
3
53
ORL A, Rn
1
6
1
48-4F
ORL A, direct
2
6
2
45
ORL A, @Ri
1
6
2
46-47
ORL A, #data
2
6
2
44
ORL direct, A
2
6
2
42
ORL direct, #data
3
12
3
43
XRL A, Rn
1
6
1
68-6F
XRL A, direct
2
6
2
65
XRL A, @Ri
1
6
2
66-67
XRL A, #data
2
6
2
64
XRL direct, A
2
6
2
62
XRL direct, #data
3
12
3
63
RL A
1
6
1
23
RLC A
1
6
1
33
RR A
1
6
1
03
RRC A
1
6
1
13
SWAP A
1
6
1
C4
Clock Cycles
Data Transfer
76
Bytes
Compatibility
Fast
Hex Code
MOV A, Rn
1
6
1
E8-EF
MOV A, direct
2
6
2
E5
MOV A, @Ri
1
6
2
E6-E7
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Table 16-1.
Instruction Execution Times and Exceptions(1) (Continued)
MOV A, #data
2
6
2
74
MOV Rn, A
1
6
1
F8-FF
MOV Rn, direct
2
12
2
A8-AF
MOV Rn, #data
2
6
2
78-7F
MOV direct, A
2
6
2
F5
MOV direct, Rn
2
12
2
88-8F
MOV direct, direct
3
12
3
85
MOV direct, @Ri
2
12
2
86-87
MOV direct, #data
3
12
3
75
MOV @Ri, A
1
6
1
F6-F7
MOV @Ri, direct
2
12
2
A6-A7
MOV @Ri, #data
2
6
2
76-77
MOV DPTR, #data16
3
12
3
90
MOV /DPTR, #data16(2)
4
–
4
A5 90
MOVC A, @A+DPTR
1
12
3
93
MOVC A, @A+/DPTR(2)
2
–
4
A5 93
MOVC A, @A+PC
1
12
3
83
MOVX A, @Ri
1
12
2
E2-E3
MOVX A, @DPTR
1
12(3)
4(3)
E0
MOVX A, @/DPTR(2)
2
18(3)
5(3)
A5 E0
MOVX @Ri, A
1
12
2
F2-F3
MOVX @DPTR, A
1
12(3)
4(3)
F0
MOVX @/DPTR, A(2)
2
18(3)
5(3)
A5 F0
PUSH direct
2
12
2
C0
POP direct
2
12
2
D0
XCH A, Rn
1
6
1
C8-CF
XCH A, direct
2
6
2
C5
XCH A, @Ri
1
6
2
C6-C7
XCHD A, @Ri
1
6
2
D6-D7
Clock Cycles
Bit Operations
Bytes
Compatibility
Fast
Hex Code
CLR C
1
6
1
C3
CLR bit
2
6
2
C2
SETB C
1
6
1
D3
SETB bit
2
6
2
D2
CPL C
1
6
1
B3
CPL bit
2
6
2
B2
ANL C, bit
2
12
2
82
ANL C, bit
2
12
2
B0
77
3709D–MICRO–12/11
Table 16-1.
Instruction Execution Times and Exceptions(1) (Continued)
ORL C, bit
2
12
2
72
ORL C, /bit
2
12
2
A0
MOV C, bit
2
6
2
A2
MOV bit, C
2
12
2
92
Clock Cycles
Branching
Bytes
Compatibility
Fast
Hex Code
JC rel
2
12
3
40
JNC rel
2
12
3
50
JB bit, rel
3
12
4
20
JNB bit, rel
3
12
4
30
JBC bit, rel
3
12
4
10
JZ rel
2
12
3
60
JNZ rel
2
12
3
70
SJMP rel
2
12
3
80
ACALL addr11
2
12
3
11,31,51,71,91,
B1,D1,F1
LCALL addr16
3
12
4
12
RET
1
12
4
22
RETI
1
12
4
32
AJMP addr11
2
12
3
01,21,41,61,81,
A1,C1,E1
LJMP addr16
3
12
4
02
JMP @A+DPTR
1
12
2
73
JMP @A+PC(2)
2
12
3
A5 73
CJNE A, direct, rel
3
12
4
B5
CJNE A, #data, rel
3
12
4
B4
CJNE Rn, #data, rel
3
12
4
B8-BF
CJNE @Ri, #data, rel
3
12
4
B6-B7
CJNE A, @R0, rel(2)
3
18
4
A5 B6
CJNE A, @R1, rel(2)
3
18
4
A5 B7
DJNZ Rn, rel
2
12
3
D8-DF
DJNZ direct, rel
3
12
4
D5
NOP
1
6
1
00
Notes:
1. A clock cycle is one period of the output of the system clock divider. For Fast mode the divider
defaults to 1, so the clock cycle equals the oscillator period. For Compatibility mode the divider
defaults to 2, so the clock cycle is twice the oscillator period, or conversely the clock count is
half the number of oscillator periods.
2. This escaped instruction is an extension to the instruction set.
3. This is the minimum time for MOVX with no wait states. In Compatibility mode an additional 24
clocks are added for the wait state. In Fast mode, 1 clock is added for each wait state (0–3).
78
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
17. Programming the Flash Memory
The Atmel AT89LP51/52 microcontroller features 8K bytes of on-chip In-System Programmable
Flash program memory and 256bytes of nonvolatile Flash data memory. In-System Programming allows programming and reprogramming of the microcontroller positioned inside the end
system. Using a simple 3-wire SPI interface, the programmer communicates serially with the
AT89LP51/52 microcontroller, reprogramming all nonvolatile memories on the chip. In-System
Programming eliminates the need for physical removal of the chips from the system. This will
save time and money, both during development in the lab, and when updating the software or
parameters in the field. The programming interface of the AT89LP51/52 includes the following
features:
• Three-wire serial SPI Programming Interface or 11-pin Parallel Interface
• Selectable Polarity Reset Entry into Programming
• User Signature Array
• Flexible Page Programming
• Row Erase Capability
• Page Write with Auto-Erase Commands
• Programming Status Register
For more detailed information on In-System Programming, refer to the Application Note entitled
“AT89LP In-System Programming Specification”.
17.1
Physical Interface
The AT89LP51/52 provides a standard programming command set with two physical interfaces:
a bit-serial and a byte-parallel interface. Normal Flash programming utilizes the Serial Peripheral
Interface (SPI) pins of an AT89LP51/52 microcontroller. The SPI is a full-duplex synchronous
serial interface consisting of three wires: Serial Clock (SCK), Master-In/Slave-out (MISO), and
Master-out/Slave-in (MOSI)). When programming an AT89LP51/52 device, the programmer
always operates as the SPI master, and the target system always operates as the SPI slave. To
enter or remain in Programming mode the device’s reset line (RST) must be held active. With
the addition of VDD and GND, an AT89LP51/52 microcontroller can be programmed with a minimum of seven connections as shown in Figure 17-1.
Figure 17-1. In-System Programming Device Connections
AT89LP51/52
Serial Clock
P1.7/SCK
Serial Out
P1.6/MISO
Serial In
P1.5/MOSI
VDD
POL
GND or VDD
RST
RST
GND
79
3709D–MICRO–12/11
The Parallel interface is a special mode of the serial interface, i.e. the serial interface is used to
enable the parallel interface. After enabling the interface serially over P1.7/SCK and P1.5/MOSI,
P1.5 is reconfigured as an active-low output enable (OE) for data on Port 0. When OE = 1, command, address and write data bytes are input on Port 0 and sampled at the rising edge of SCK.
When OE = 0, read data bytes are output on Port 0 and should be sampled on the falling edge of
SCK. The P1.7/SCK and RST pins continue to function in the same manner. With the addition of
VDD and GND, the parallel interface requires a minimum of fourteen connections as shown in
Figure 17-2. Note that a connection to P1.6/MISO is not required for using the parallel interface.
Figure 17-2. Parallel Programming Device Connections
AT89LP51/52
Clock
RST
OE
GND or VDD
P1.7/SCK
RST
VDD
P1.5/MOSI
POL
P0.7-0
8
Data In/Out
GND
The Programming Interface is the only means of externally programming the AT89LP51/52
microcontroller. The Interface can be used to program the device both in-system and in a standalone serial programmer. The Interface does not require any clock other than SCK and is not
limited by the system clock frequency. During Programming the system clock source of the target device can operate normally.
When designing a system where In-System Programming will be used, the following observations must be considered for correct operation:
• The ISP interface uses the SPI clock mode 0 (CPOL = 0, CPHA = 0) exclusively with a
maximum frequency of 5 MHz.
• The AT89LP51/52 will enter programming mode only when its reset line (RST) is active. To
simplify this operation, it is recommended that the target reset can be controlled by the InSystem programmer. To avoid problems, the In-System programmer should be able to keep
the entire target system reset for the duration of the programming cycle. The target system
should never attempt to drive the three SPI lines while reset is active.
• The ISP Enable Fuse must be set to allow programming during any reset period. If the ISP
Fuse is disabled, ISP may only be entered at POR. To enter programming the RST pin must
be driven active prior to the end of Power-On Reset (POR). After POR has completed the
device will remain in ISP mode until RST is brought inactive. Once the initial ISP session has
ended, the power to the target device must be cycled OFF and ON to enter another session.
Note that if this method is required, an active-low reset polarity is recommended.
• For standalone programmers, an active-low reset polarity is recommended (POL = 0). RST
may then be tied directly to GND to ensure correct entry into Programming mode regardless
of the device settings.
80
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
17.2
Memory Organization
The AT89LP51/52 offers 8K bytes of In-System Programmable (ISP) nonvolatile Flash code
memory and 256 bytes of nonvolatile Flash data memory. In addition, the device contains a 256byte User Signature Array and a 128-byte read-only Atmel Signature Array. The memory organization is shown in Table 17-1 and Figure 17-3. The memory is divided into pages of 128 bytes
each. A single read or write command may only access half a page (64 bytes) in the memory;
however, write with auto-erase commands will erase an entire 128-byte page even though they
can only write one half page. Each memory type resides in its own address space and is
accessed by commands specific to that memory. However, all memory types share the same
page size.
User configuration fuses are mapped as a row in the memory, with each byte representing one
fuse. From a programming standpoint, fuses are treated the same as normal code bytes except
they are not affected by Chip Erase. Fuses can be enabled at any time by writing 00h to the
appropriate locations in the fuse row. However, to disable a fuse, i.e. set it to FFh, the entire
fuse row must be erased and then reprogrammed. The programmer should read the state of all
the fuses into a temporary location, modify those fuses which need to be disabled, then issue a
Fuse Write with Auto-Erase command using the temporary data. Lock bits are treated in a similar manner to fuses except they may only be erased (unlocked) by Chip Erase.
Table 17-1.
AT89LP51/52 Memory Organization
Memory
Capacity
Page Size
# Pages
Address Range
CODE
4096 bytes
8192 bytes
128 bytes
32
64
0000H – 0FFFH
0000H – 1FFFH
DATA
256 bytes
128 bytes
2
0000H – 00FFH
User Signature
256 bytes
128 bytes
2
0000H – 00FFH
Atmel Signature
128 bytes
128 bytes
1
0000H – 007FH
Figure 17-3. AT89LP52 Memory Organization
00
3F
Page Buffer
User Fuse Row
Page 0 Low
User Signature Array
Page 1 Low
Page 0 Low
Page 1 High
Page 0 High
Atmel Signature Array
Page 0 Low
Page 0 High
Data Memory
Page 1 Low
Page 0 Low
Page 1 High
Page 0 High
Page 63 Low
Page 63 High
Page 62 Low
Page 62 High
Page 1 Low
Page 0 Low
Page 1 High
Page 1 High
1FFF
Code Memory
00
3F 40
0000
7F
81
3709D–MICRO–12/11
17.3
Command Format
Programming commands consist of an opcode byte, two address bytes, and one or 64 data
bytes. Figure 17-4 on page 82 shows a simplified flow chart of a command sequence.
A sample command packet is shown in Figure 17-5 on page 83. The packet does not use a chip
select. Command bytes are issued serially on MOSI. Data output bytes are received serially on
MISO. The command is not complete until all bytes have been transfered, including any don’t
care bytes.
Page oriented instructions always include a full 16-bit address. The higher order bits select the
page and the lower order bits select the byte within that page. The AT89LP51/52 allocates 6 bits
for byte address, 1 bit for low/high half page selection and 9 bits for page address. The half page
to be accessed is always fixed by the page address and half select as transmitted. The byte
address specifies the starting address for the first data byte. After each data byte has been
transmitted, the byte address is incremented to point to the next data byte. This allows a page
command to linearly sweep the bytes within a page. If the byte address is incremented past the
last byte in the half page, the byte address will roll over to the first byte in the same half page.
While loading bytes into the page buffer, overwriting previously loaded bytes will result in data
corruption.
For a summary of available commands, see Table 17-2 on page 84.
Figure 17-4. Command Sequence Flow Chart
Input Opcode
Input Address
High Byte
Input Address
Low Byte
Input/Output
Data
Byte Mode or
Count == 64
Address +1
no
yes
82
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 17-5. ISP Command Packet (Serial Byte)
SCK
MOSI
MISO
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
Opcode
Address High
Address Low
Data In
X
X
X
7 6 5 4 3 2 1 0
Data Out
Figure 17-6. ISP Command Packet (Serial Page)
SCK
MOSI
MISO
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
Opcode
Address High
Address Low
Data In 0
Data In 63
X
X
X
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
Data Out 0
Data Out 63
Figure 17-7. ISP Command Packet (Parallel Byte)
SCK
WRITE
OE
P0
Opcode
Address High
Address Low
Data In
READ
OE
P0
Opcode
Address High
Data Out
Address Low
Figure 17-8. ISP Command Packet (Parallel Page)
SCK
WRITE
OE
P0
Opcode
Address High
Address Low
Data In 0
Data In 63
READ
OE
P0
Opcode
Address High
Address Low
Data Out 0
Out 62
Data Out 63
83
3709D–MICRO–12/11
Table 17-2.
Programming Command Summary
Command
Opcode
Addr High
Addr Low
Data 0
Data 1–63
Program Enable(1)
1010 1100
0101 0011
xxxx xxxx
xxxx xxxx
(0110 1001)(2)
–
Parallel Enable(3)
1010 1100
0011 0101
xxxx xxxx
xxxx xxxx
–
Chip Erase
1010 1100
100x xxxx
xxxx xxxx
xxxx xxxx
–
Read Status
0110 0000
xxxx xxxx
xxxx xxxx
Status Out
–
Write Code Byte
0100 0000
000a aaaa
asbb bbbb
Data In
–
Read Code Byte
0010 0000
000a aaaa
asbb bbbb
Data Out
–
Write Code Page
0101 0000
000a aaaa
as00 0000
Byte 0
Bytes 1–63
Write Code Page with Auto-Erase
0111 0000
000a aaaa
as00 0000
Byte 0
Bytes 1–63
Read Code Page
0011 0000
000a aaaa
as00 0000
Byte 0
Bytes 1–63
Write Data Byte
1100 0000
xxxx xxxx
asbb bbbb
Data In
–
Read Data Byte
1010 0000
xxxx xxxx
asbb bbbb
Data Out
–
Write Data Page
1101 0000
xxxx xxxx
as00 0000
Byte 0
Bytes 1–63
Write Data Page with Auto-Erase
1101 0010
xxxx xxxx
as00 0000
Byte 0
Bytes 1–63
Read Data Page
1011 0000
xxxx xxxx
as00 0000
Byte 0
Bytes 1–63
Write User Fuse
(5)
Read User Fuse
0100 0001
(5)
Write User Fuses
0010 0001
(5)
0101 0001
xxxx xxxx
xxxx xxxx
00bb bbbb
00bb bbbb
0000 0000
Fuse In
Fuse Out
(4)
–
–
(4)
Bytes 1–63
(4)
Fuse 0
0111 0001
xxxx xxxx
0000 0000
Fuse 0
Fuses 1–63(4)
Read User Fuses(5)
0011 0001
xxxx xxxx
0000 0000
Fuse 0(4)
Fuses 1–63(4)
Write Lock Mode(6)
1010 1100
1110 00BB
xxxx xxxx
xxxx xxxx
–
(6)
0010 0100
xxxx xxxx
xxxx xxxx
xxxL LLxx
–
00bb bbbb
(4)
–
(4)
Write User Fuses with Auto-Erase
Read Lock Mode
(5)
xxxx xxxx
(4)
(6)
Write Lock Bit
0100 0100
xxxx xxxx
Data In
(6)
0101 0100
xxxx xxxx
0000 0000
Byte 0
Bytes 1–63(4)
Read Lock Bits(6)
0011 0100
xxxx xxxx
0000 0000
Byte 0(4)
Bytes 1–63(4)
Write User Signature Byte
0100 0010
xxxx xxxx
asbb bbbb
Data In
–
Read User Signature Byte
0010 0010
xxxx xxxx
asbb bbbb
Data Out
–
Write User Signature Page
0101 0010
xxxx xxxx
as00 0000
Byte 0
Byte 1–63
Write User Signature Page with Auto-Erase
0111 0010
xxxx xxxx
as00 0000
Byte 0
Byte 1–63
Read User Signature Page
0011 0010
xxxx xxxx
as00 0000
Byte 0
Byte 1–63
0010 1000
xxxx xxxx
0sbb bbbb
Data Out
–
0011 1000
xxxx xxxx
0s00 0000
Byte 0
Byte 1–63
Write Lock Bits
(7)
Read Atmel Signature Byte
Read Atmel Signature Page
Notes:
(7)
1. Program Enable must be the first command issued after entering into programming mode.
2. 0110 1001B is returned on MISO when Program Enable was successful.
3. Parallel Enable switches the interface from serial to parallel format until RST goes inactive.
4. Each byte address selects one fuse or lock bit. Data bytes must be 00h or FFh.
5. See Table 17-5 on page 86 for Fuse definitions.
6. See Table 17-4 on page 86 for Lock Bit definitions.
84
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
7. Atmel Signature Bytes:
Address:
0000H
0001H
0002H
AT89LP51:
1EH
54H
05H
AT89LP52:
1EH
54H
06H
8. Symbol Key:
17.4
a:
Page Address Bit
s:
Half Page Select Bit
b:
Byte Address Bit
x:
Don’t Care Bit
Status Register
The current state of the memory may be accessed by reading the status register. The status register is shown in Table 17-3.
Table 17-3.
Status Register
Bit
–
–
–
–
LOAD
SUCCESS
WRTINH
BUSY
7
6
5
4
3
2
1
0
Symbol
Function
LOAD
Load flag. Cleared low by the load page buffer command and set high by the next memory write. This flag signals that
the page buffer was previously loaded with data by the load page buffer command.
SUCCESS
Success flag. Cleared low at the start of a programming cycle and will only be set high if the programming cycle
completes without interruption from the brownout detector.
WRTINH
Write Inhibit flag. Cleared low by the brownout detector (BOD) whenever programming is inhibited due to VDD falling
below the minimum required programming voltage. If a BOD episode occurs during programming, the SUCCESS flag
will remain low after the cycle is complete.
BUSY
Busy flag. Cleared low whenever the memory is busy programming or if write is currently inhibited.
17.5
DATA Polling
The AT89LP51/52 implements DATA polling to indicate the end of a programming cycle. While
the device is busy, any attempted read of the last byte written will return the data byte with the
MSB complemented. Once the programming cycle has completed, the true value will be accessible. During Erase the data is assumed to be FFH and DATA polling will return 7FH. When
writing multiple bytes in a page, the DATA value will be the last data byte loaded before programming begins, not the written byte with the highest physical address within the page.
17.6
Flash Security
The AT89LP51/52 provides three Lock Bits for Flash Code and Data Memory security. Lock bits
can be left unprogrammed (FFh) or programmed (00h) to obtain the protection levels listed in
Table 17-4. Lock bits can only be erased (set to FFh) by Chip Erase. Lock bit mode 2 disables
programming of all memory spaces, including the User Signature Array and User Configuration
Fuses. User fuses must be programmed before enabling Lock bit mode 2 or 3. Lock bit mode 3
85
3709D–MICRO–12/11
implements mode 2 and also blocks reads from the code and data memories; however, reads of
the User Signature Array, Atmel Signature Array, and User Configuration Fuses are still allowed.
The Lock Bits will not disable FDATA or IAP programming initiated by the application software.
Table 17-4.
Lock Bit Protection Modes
Program Lock Bits (by address)
Mode
00h
01h
02h
Protection Mode
1
FFh
FFh
FFh
No program lock features
2
00h
FFh
FFh
Further programming of the Flash is disabled
3
00h
00h
FFh
Further programming of the Flash is disabled and verify (read) is also disabled
4
00h
00h
00h
Further programming of the Flash is disabled and verify (read) is also disabled;
External execution above 4K/8K is disabled
17.7
User Configuration Fuses
The AT89LP51/52 includes 10 user fuses for configuration of the device. Each fuse is accessed
at a separate address in the User Fuse Row as listed in Table 17-5. Fuses are cleared by programming 00h to their locations. Programming FFh to a fuse location will cause that fuse to
maintain its previous state. To set a fuse (set to FFh) the fuse row must be erased and then
reprogrammed using the Fuse Write with Auto-erase command. The default state for all fuses is
FFh except for Tristate Ports, which defaults to 00h.
Table 17-5.
Address
User Configuration Fuse Definitions
Fuse Name
Description
Selects source for the system clock:
00 – 01h
Clock Source – CS[0:1](2)
CS1
CS0
Selected Source
FFh
FFh
High Speed Crystal Oscillator (XTAL)
FFh
00h
Low Speed Crystal Oscillator (XTAL)
00h
FFh
External Clock on XTAL1 (XCLK)
00h
00h
Internal Auxiliary Oscillator (IRC)
Selects time-out delay for the POR/BOD/PWD wake-up period:
02 – 03h
Start-up Time – SUT[0:1]
SUT1
SUT0
Selected Time-out
00h
00h
1 ms (XTAL); 16 µs (XCLK/IRC)
00h
FFh
2 ms (XTAL); 512 µs (XCLK/IRC)
FFh
00h
4 ms (XTAL); 1 ms (XCLK/IRC)
FFh
FFh
16 ms (XTAL); 4 ms (XCLK/IRC)
04h
Compatibility Mode
FFh: CPU functions in 12-clock Compatibility mode
00h: CPU functions is single-cycle Fast mode
05h
ISP Enable(3)
FFh: In-System Programming Enabled
00h: In-System Programming Disabled (Enabled at POR only)
06H
User Signature Programming
FFh: Programming of User Signature Disabled
00h: Programming of User Signature Enabled
86
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Table 17-5.
User Configuration Fuse Definitions
Address
Fuse Name
Description
07H
Tristate Ports
FFh: I/O Ports start in input-only mode (tristated) after reset
00h: I/O Ports start in quasi-bidirectional mode after reset
08H
In-Application Programming
FFh: In-Application Programming Disabled
00h: In-Application Programming Enabled
09H
R1 Enable
FFh: 5 MΩ resistor on XTAL1 Disabled
00h: 5 MΩ resistor on XTAL1 Enabled
Notes:
1. The default state for Tristate Ports is 00h. All other fuses default to FFh.
2. Changes to these fuses will only take effect after a device POR.
3. Changes to these fuses will only take effect after the ISP session terminates by bringing RST inactive.
17.8
User Signature
The User Signature Array contains 256 bytes of non-volatile memory in two 128-byte pages. The
User Signature is available for serial numbers, firmware revision information, date codes or other
user parameters. The User Signature Array may only be written by an external device when the
User Signature Programming Fuse is enabled. When the fuse is enabled, Chip Erase will also
erase the first page of the array. When the fuse is disabled, the array is not affected by write or
erase commands. Programming of the Signature Array can also be disabled by the Lock Bits.
However, reading the signature is always allowed and the array should not be used to store
security sensitive information. The User Signature Array may be modified during execution
through the In-Application Programming interface, regardless of the state of the User Signature
Programming fuse or Lock Bits, provided that the IAP Fuse is enabled. Note that the address of
the User Signature Array, as seen by the IAP interface, equals the User Signature address plus
256 (0100H–01FFH instead of 0000H–00FFH).
17.9
Programming Interface Timing
This section details general system timing sequences and constraints for entering or exiting InSystem Programming as well as parameters related to the Serial Peripheral Interface during
ISP. The general timing parameters for the following waveform figures are listed in section “Timing Parameters” on page 91.
17.9.1
Power-up Sequence
Execute this sequence to enter programming mode immediately after power-up. In the RST pin
is disabled or if the ISP Fuse is disabled, this is the only method to enter programming (see
“External Reset” on page 33).
1. Apply power between VDD and GND pins. RST should remain low.
2. Wait at least tPWRUP. and drive RST high if active-high otherwise keep low.
3. Wait at least tSUT for the internal Power-on Reset to complete. The value of tSUT will
depend on the current settings of the device.
4. Start programming session.
87
3709D–MICRO–12/11
Figure 17-9. Serial Programming Power-up Sequence
VDD
tPWRUP
RST
tPOR + tSUT
RST
SCK
17.9.2
MISO
HIGH Z
MOSI
HIGH Z
Power-down Sequence
Execute this sequence to power-down the device after programming.
1. Drive SCK low.
2. Wait at least tSSD and Tristate MOSI.
3. Wait at least tRHZ and drive RST low.
4. Wait at least tSSZ and tristate SCK.
5. Wait no more than tPWRDN and power off VDD.
Figure 17-10. Serial Programming Power-down Sequence
VDD
tPWRDN
RST
SCK
17.9.3
tSSD
tRHZ
tSSZ
MISO
HIGH Z
MOSI
HIGH Z
ISP Start Sequence
Execute this sequence to exit CPU execution mode and enter ISP mode when the device has
passed Power-On Reset and is already operational.
1. Drive RST high.
2. Wait tRLZ + tSTL.
3. Drive SCK low.
4. Start programming session.
88
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 17-11. In-System Programming (ISP) Start Sequence
VDD
XTAL1
tRLZ
RST
tSTL
tZSS
tSSE
SCK
17.9.4
MISO
HIGH Z
MOSI
HIGH Z
ISP Exit Sequence
Execute this sequence to exit ISP mode and resume CPU execution mode.
1. Drive SCK low.
1. Wait at least tSSD.
2. Tristate MOSI.
3. Wait at least tRHZ and bring RST low.
4. Wait tSSZ and tristate SCK.
Figure 17-12. In-System Programming (ISP) Exit Sequence
VDD
XTAL1
RST
SCK
Note:
17.9.5
tSSD
tRHZ
tSSZ
MISO
HIGH Z
MOSI
HIGH Z
The waveforms on this page are not to scale.
Serial Peripheral Interface
The Serial Peripheral Interface (SPI) is a byte-oriented full-duplex synchronous serial communication channel. During In-System Programming, the programmer always acts as the SPI master
and the target device always acts as the SPI slave. The target device receives serial data on
MOSI and outputs serial data on MISO. The Programming Interface implements a standard
SPI Port with a fixed data order and For In-System Programming, bytes are transferred MSB
first as shown in Figure 17-13. The SCK phase and polarity follow SPI clock mode 0 (CPOL = 0,
CPHA = 0) where bits are sampled on the rising edge of SCK and output on the falling edge of
SCK. For more detailed timing information see Figure 17-14.
89
3709D–MICRO–12/11
Figure 17-13. ISP Byte Sequence
SCK
MOSI
7
6
5
4
3
2
1
0
MISO
7
6
5
4
3
2
1
0
Data Sampled
Figure 17-14. Serial Programming Interface Timing
RST
tSCK
tSSE
tSHSL
SCK
tSR
tSSD
tSF
tSLSH
tSOV
tSOX
tSOH
MISO
tSIS
tSIH
MOSI
Figure 17-15. Parallel Programming Interface Timing
RST
tSCK
tSSE
tSHSL
SCK
tSR
tSF
tSSD
tSLSH
OE
tPIS
tPIH
tPOE
tPOV
tPOH
tPOX
P0
90
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
17.9.6
Timing Parameters
The timing parameters for Figure 17-9, Figure 17-10, Figure 17-11, Figure 17-12, Figure 17-14
and Figure 17-15 are shown in Table .
Table 17-6.
Symbol
Parameter
Min
Max
Units
60
ns
tCLCL
System Clock Cycle Time
0
tPWRUP
Power On to SS High Time
10
tPOR
Note:
Programming Interface Timing Parameters
Power-on Reset Time
µs
100
µs
1
µs
2 tCLCL
ns
tPWRDN
SS Tristate to Power Off
tRLZ
RST Low to I/O Tristate
tCLCL
tSTL
RST Low Settling Time
100
tRHZ
RST High to SS Tristate
0
tSCK
Serial Clock Cycle Time
200(1)
ns
tSHSL
Clock High Time
75
ns
tSLSH
Clock Low Time
50
ns
ns
2 tCLCL
ns
tSR
Rise Time
25
ns
tSF
Fall Time
25
ns
tSIS
Serial Input Setup Time
10
ns
tSIH
Serial Input Hold Time
10
ns
tSOH
Serial Output Hold Time
10
ns
tSOV
Serial Output Valid Time
35
ns
tPIS
Parallel Input Setup Time
10
ns
tPIH
Parallel Input Hold Time
10
ns
tPOH
Parallel Output Hold Time
10
ns
tPOV
Parallel Output Valid Time
35
ns
tSOE
Serial Output Enable Time
10
ns
tSOX
Serial Output Disable Time
25
ns
tPOE
Parallel Output Enable Time
10
ns
tPOX
Parallel Output Disable Time
25
ns
tSSE
RST Active Lead Time
tSLSH
ns
tSSD
RST Inactive Lag Time
tSLSH
ns
tZSS
SCK Setup to SS Low
25
ns
tSSZ
SCK Hold after SS High
25
ns
tWR
Write Cycle Time
2.5
ms
tAWR
Write Cycle with Auto-Erase Time
5
ms
7.5
ms
tERS
Chip Erase Cycle Time
1. tSCK is independent of tCLCL.
91
3709D–MICRO–12/11
18. Electrical Characteristics
18.1
Absolute Maximum Ratings*
Operating Temperature ................................... -40°C to +85°C
*NOTICE:
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin with Respect to Ground......-0.7V to +5.5V
Maximum Operating Voltage ............................................ 5.5V
Total DC Output Current ........................................... 150.0 mA
18.2
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
DC Characteristics
TA = -40°C to 85°C, VDD = 2.4V to 5.5V (unless otherwise noted)
Symbol
Parameter
VIL
Input Low-voltage
VIH
Input High-voltage
VOL
Output Low-voltage(1)
VOH
Output High-voltage
With Weak Pull-ups Enabled
Condition
Max
Units
-0.5
min(0.25VDD,
0.8(3))
V
min(0.7VDD,
2.4(3))
VDD + 0.5
V
IOL = 8 mA, VDD = 5V ± 10%
V
0.5
IOL = 4 mA, VDD = 2.4V
IOH = -60 µA, VDD = 5V ± 10%
2.4
V
IOH = -25 µA
0.7 VDD
V
IOH = -10 µA
0.85 VDD
V
IOH = -7 mA, VDD = 5V ± 10%
VOH1
Min
Output High-voltage
With Strong Pull-ups Enabled
0.9 VDD
IOH = -2.5 mA, VDD = 2.4V
IOH = -10 mA, VDD = 5V ± 10%
0.75 VDD
IOH = -6 mA, VDD = 2.4V
IIL
Logic 0 Input Current
VIN = 0.45V
-50
µA
ITL
Logic 1 to 0 Transition Current
VIN = 2V, VDD = 5V ± 10%
-200
µA
ILI
Input Leakage Current
0 < VIN < VDD
±10
µA
CIO
Pin Capacitance
Test Freq. = 1 MHz, TA = 25°C
10
pF
Power Supply Current
(Fast Mode)
Active Mode, 12 MHz, VDD = 5V
10
mA
Idle Mode, 12 MHz, VDD = 5V
3
mA
Power Supply Current
(Compatibility Mode)
Active Mode, 12 MHz, VDD = 5V
4
mA
Idle Mode, 12 MHz, VDD = 5V
2
mA
VDD = 5V
5
µA
VDD = 3V
2
µA
ICC
Power-down Mode(2)
Notes:
92
1. Under steady state (non-transient) conditions, IOL must be externally limited as follows:
Maximum IOL per port pin: 10 mA
Maximum total IOL for all output pins: 100 mA
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test conditions.
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
2. Minimum VDD for Power-down is 2V.
3. Inputs are TTL-compatible when VDD is 5V ± 10%
18.3
Typical Characteristics
The following charts show typical behavior. These figures are not tested during manufacturing.
All current consumption measurements are performed with all I/O pins configured as quasi-bidirectional (with internal pull-ups). A square wave generator with rail-to-rail output is used as an
external clock source for consumption versus frequency measurements.
18.3.1
Supply Current (Internal Oscillator)
Figure 18-1. Active Supply Current vs. Vcc (1.8432 MHz Internal Oscillator)
Active Supply Current vs. Vcc
1.8432 MHz Internal Oscillator
1.25
85C
Compatibility Mode
-40C
Icc (mA)
1.00
25C
0.75
0.50
0.25
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Vcc (V)
3.0
85C
Fast Mode
-40C
Icc (mA)
2.5
25C
2.0
1.5
1.0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Vcc (V)
93
3709D–MICRO–12/11
Figure 18-2. Idle Supply Current vs. Vcc (1.8432 MHz Internal Oscillator)
Idle Supply Current vs. Vcc
1.8432 MHz Internal Oscillator
0.60
85C
Compatibility Mode
-40C
Icc (mA)
0.45
25C
0.30
0.15
0.00
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Vcc (V)
0.8
85C
Fast Mode
-40C
Icc (mA)
0.6
25C
0.4
0.2
0.0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Vcc (V)
94
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
18.3.2
Supply Current (External Clock)
Figure 18-3. Active Supply Current vs. Frequency
Active Supply Current vs. Frequency
External Clock Source
8
5.5V
Compatibility Mode
7
5.0V
Icc (mA)
6
5
4.5V
4
3.6V
3
3.0V
2
2.4V
1
0
0
5
10
15
20
25
Frequency (MHz)
20
5.5V
Fast Mode
18
5.0V
16
Icc (mA)
14
4.5V
12
3.6V
10
8
3.0V
6
2.4V
4
2
0
0
5
10
15
20
25
Frequency (MHz)
20
5V Compat.
18
3V Compat.
16
Icc (mA)
14
5V Fast
12
3V Fast
10
8
6
4
2
0
0
5
10
15
20
25
MIPS
95
3709D–MICRO–12/11
Figure 18-4. Idle Supply Current vs. Frequency
Idle Supply Current vs. Frequency
External Clock Source
Icc (mA)
3.0
5.5V
Compatibility Mode
2.5
5.0V
2.0
4.5V
1.5
3.6V
1.0
3.0V
2.4V
0.5
0.0
0
5
10
15
20
25
Frequency (MHz)
Icc (mA)
6
5.5V
Fast Mode
5
5.0V
4
4.5V
3
3.6V
2
3.0V
2.4V
1
0
0
5
10
15
20
25
Frequency (MHz)
96
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
18.3.3
Quasi-Bidirectional Input
Figure 18-5. Quasi-bidirectional Input Transition Current at 5V
0.0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
85C
-40C
ITL (μA)
-30
25C
-60
-90
-120
-150
VIL (V)
Figure 18-6. Quasi-bidirectional Input Transition Current at 3V
0.0
0
0.5
1.0
1.5
2.0
2.5
3.0
85C
-10
-40C
ITL (μA)
-20
25C
-30
-40
-50
-60
-70
-80
VIL (V)
97
3709D–MICRO–12/11
18.3.4
Quasi-Bidirectional Output
Figure 18-7. Quasi-Bidirectional Output I-V Source Characteristic at 5V
1
2
3
4
5
0
85C
-20
-40C
IOH (μA)
-40
25C
-60
-80
-100
-120
-140
VOH (V)
Figure 18-8. Quasi-Bidirectional Output I-V Source Characteristic at 3V
1.0
0
1.5
2.0
3.0
85C
-10
-40C
-20
IOH (μA)
2.5
25C
-30
-40
-50
-60
-70
98
VOH (V)
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
18.3.5
Push-Pull Output
Figure 18-9. Push-Pull Output I-V Source Characteristic at 5V
0
1
2
3
4
5
0
85C
-40C
IOH1 (mA)
-2
25C
-4
-6
-8
-10
VOH1 (V)
Figure 18-10. Push-Pull Output I-V Source Characteristic at 3V
0
1
2
0
85C
-40C
-2
IOH1 (mA)
3
25C
-4
-6
-8
-10
VOH1 (V)
99
3709D–MICRO–12/11
Figure 18-11. Push-Pull Output I-V Sink Characteristic at 5V
10
85C
-40C
IOL (mA)
8
25C
6
4
2
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
VOL (V)
Figure 18-12. Push-Pull Output I-V Sink Characteristic at 3V
10
85C
-40C
IOL (mA)
8
25C
6
4
2
0
0.0
0.2
0.4
0.6
0.8
1.0
VOL (V)
Note:
18.4
The IOL/VOL characteristic applies to Push-Pull, Quasi-Bidirectional and Open-Drain modes.
Clock Characteristics
The values shown in this table are valid for TA = -40°C to 85°C and VDD = 2.4 to 5.5V, unless otherwise noted.
Figure 18-13. External Clock Drive Waveform
100
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Table 18-1.
External Clock Parameters
VDD = 2.4V to 5.5V
VDD = 4.5V to 5.5V
Min
Max
Min
Max
Units
20
0
25
MHz
Symbol
Parameter
1/tCLCL
Oscillator Frequency(1)
0
tCLCL
Clock Period
50
40
ns
tCHCX
External Clock High Time
15
12
ns
tCLCX
External Clock Low Time
15
12
ns
tCLCH
External Clock Rise Time
5
5
ns
tCHCL
External Clock Fall Time
5
5
ns
Min
Max
Units
Low Power Oscillator
0
12
MHz
High Power Oscillator
0
24
MHz
TA = 25°C; VDD = 5.0V
1.824
1.862
MHz
VDD = 2.4 to 5.5V
1.751
1.935
MHz
Note:
1. No wait state (single-cycle) fetch speed for Fast Mode
Table 18-2.
Clock Characteristics
Symbol
Parameter
fXTAL
Crystal Oscillator Frequency
fRC
Internal Oscillator Frequency
18.5
Condition
Reset Characteristics
The values shown in this table are valid for TA = -40°C to 85°C and VDD = 2.4 to 5.5V, unless otherwise noted.
Table 18-3.
Symbol
Reset Characteristics
Min
Max
Units
Reset Pull-up Resistor
150
300
kΩ
Reset Pull-down Resistor
100
200
kΩ
VPOR
Power-On Reset Threshold
1.3
1.6
V
VBOD
Brown-Out Detector Threshold
1.9
2.2
V
VBH
Brown-Out Detector Hysteresis
200
300
mV
tPOR
Power-On Reset Delay
135
150
µs
tWDTRST
Watchdog Reset Pulse Width
RRST
Parameter
Condition
49tCLCL
ns
101
3709D–MICRO–12/11
18.6
External Memory Characteristics
The values shown in this table are valid for TA = -40°C to 85°C and VDD = 2.4 to 5.5V, unless otherwise noted. Under operating conditions, load capacitance for Port 0, ALE and PSEN = 100 pF; load capacitance for all other outputs = 80 pF.
Parameters refer to Figure 18-14, Figure 18-15 and Figure 18-16.
Table 18-4.
External Program and Data Memory Characteristics
Compatibility Mode(1)
Symbol
1/tCLCL
tLHLL
tAVLL
Parameter
System Frequency
(6)
ALE Pulse Width
Address Valid to ALE Low
tLLAX
Address Hold after ALE Low
tLLIV
ALE Low to Valid Instruction In
tLLPL
tPLPH
ALE Low to PSEN Low
PSEN Pulse WIdth
tPLIV
PSEN Low to Valid Instruction In
tPXIX
Input Instruction Hold after PSEN
tPXIZ
tPXAV
tAVIV
Address to Valid Instruction In
tPLAZ
PSEN Low to Address Float
tRLRH
Min
Max
Min
0
24
0
tCLCL - 10
tCLCL - 10
0.5tCLCL - 20
(2)
0.5tCLCL - 20
(3)
0.5tCLCL - 20
(2)
1.5tCLCL - 10
(2)
RD Pulse Width
(5)
(5)
1.5tCLCL - 30
0.5tCLCL - 20
(2)
0.5tCLCL - 20
(2)
2.5tCLCL - 30
4tCLCL - 30
tRLAZ
Data Hold after WR
1.5tCLCL - 30
0.5tCLCL - 20
(2)
2.5tCLCL - 30
(2)
ns
ns
(2)
(2)
ns
ns
10
2.5tCLCL - 30
ns
ns
tCLCL - 30
0
ns
0
4.5tCLCL - 30
1.5tCLCL - 20
2tCLCL - 20
(2)
1tCLCL - 20
(2)
4tCLCL - 20
(2)
1tCLCL - 20
(3)
RD Low to Address Float
Address Hold after RD or WR High
1tCLCL - 20
tWHLH
RD or WR High to ALE High
0.5tCLCL - 20
ns
2tCLCL - 30
(2)
1.5tCLCL + 20
-1tCLCL + 20
ns
tCLCL - 20
2.5tCLCL - 30
tCLCL - 20
tCLCL + 20
ns
ns
1.5tCLCL - 20
ns
0.5tCLCL - 20
(2)
ns
1.5tCLCL - 20
(2)
ns
0.5tCLCL - 20
(3)
ns
-0.5tCLCL + 20
0.5tCLCL - 20
0.5tCLCL + 20
ns
(2)
(2)
(2)
(3)
tWHAX
Notes:
ns
(2)
ns
ALE Low to Valid Data In
tWHQX
ns
tCLCL - 10
tLLDV
Data Valid to WR High
1.5tCLCL - 10
(2)
ns
3tCLCL - 10
tCLCL - 20
tQVWH
0.5tCLCL - 20
(2)
ns
Data Float after RD
Data Valid to WR Transition
ns
tCLCL - 10
tRHDZ
tQVWX
0.5tCLCL - 20
3tCLCL - 10
Data Hold after RD
Address to RD or WR Low
ns
(3)
10
tRHDX
tAVWL
ns
0.5tCLCL - 20
0.5tCLCL - 20
RD Low to Valid Data In
ALE Low to RD or WR Low
MHz
0
tRLDV
tLLWL
24
(2)
0
WR Pulse Width
Address to Valid Data In
Units
2tCLCL - 30
(2)
tWLWH
tAVDV
Max
(4)
2tCLCL - 30
Input Instruction Float after PSEN
PSEN to Address Valid
Fast Mode(1)
(3)
(2)
ns
ns
tCLCL - 20
ns
1. Compatibility Mode timing for MOVX also applies to Fast Mode during exeternal execution of MOVX.
2. This assumes 50% clock duty cycle. The half period depends on the clock high value tCHCX (high duty cycle).
3. This assumes 50% clock duty cycle. The half period depends on the clock low value tCLCX (low duty cycle).
4. In some cases parameter tLHLL may have a minimum of 0.5tCLCL during Fast mode external execution with DISALE = 0.
5. The strobe pulse width may be lengthened by 1, 2 or 3 additional tCLCL using wait states.
6. tCLCL is the internal system clock period. By default in Compatibility Mode, tCLCL = 2 tOSC
102
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Figure 18-14. External Program Memory Read Cycle
tLHLL
ALE
tAVLL
tLLPL
tPLIV
PSEN
tPLAZ
tLLAX
tPXAV
tPXIZ
tPXIX
A0 - A7
PORT 0
tPLPH
tLLIV
INSTR IN
A0 - A7
tAVIV
A8 - A15
PORT 2
A8 - A15
Figure 18-15. External Data Memory Read Cycle
tLHLL
ALE
tLLDV
tLLWL
tWHLH
tRLRH
RD
tRLAZ
tAVLL
PORT 0
tRLDV
tLLAX
tRHDX
DATA IN
A0 - A7
tAVWL
tAVDV
PORT 2
P2
tRHDZ
tWHAX
A8 - A15 FROM DPH OR P2.0 - P2.7
P2
Figure 18-16. External Data Memory Write Cycle
tLHLL
ALE
tLLWL
tWLWH
tWHLH
WR
tQVWX
tAVLL
PORT 0
tWHQX
tLLAX
A0 - A7
DATA OUT
tQVWH
tAVWL
PORT 2
P2
A8 - A15 FROM DPH OR P2.0 - P2.7
tWHAX
P2
103
3709D–MICRO–12/11
18.7
Serial Port Timing: Shift Register Mode
The values in this table are valid for VDD = 2.4V to 5.5V and Load Capacitance = 80 pF.
SMOD1 = 0
Min
SMOD1 = 1
Symbol
Parameter
Max
Min
Max
Units
tXLXL
Serial Port Clock Cycle Time
4tCLCL -15
2tCLCL -15
µs
tQVXH
Output Data Setup to Clock Rising Edge
3tCLCL -15
tCLCL -15
ns
tXHQX
Output Data Hold after Clock Rising Edge
tCLCL -15
tCLCL -15
ns
tXHDX
Input Data Hold after Clock Rising Edge
0
0
ns
tXHDV
Input Data Valid to Clock Rising Edge
15
15
ns
Figure 18-17. Shift Register Mode Timing Waveform
SMOD1 = 0
Clock
Write to SBUF
Output Data
0
1
2
3
4
5
6
7
Clear RI
Input Data
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
SMOD1 = 1
Clock
Write to SBUF
0
Output Data
1
2
3
4
5
6
7
Clear RI
Input Data
18.8
18.8.1
Note:
104
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Valid
Test Conditions
AC Testing Input/Output Waveform(1)
1. AC Inputs during testing are driven at VDD - 0.5V for a logic “1” and 0.45V for a logic “0”. Timing measurements are made at
VIH min. for a logic “1” and VIL max. for a logic “0”.
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
18.8.2
Note:
18.8.3
Float Waveform(1)
1. For timing purposes, a port pin is no longer floating when a 100 mV change from load voltage occurs. A port pin begins to
float when 100 mV change from the loaded VOH/VOL level occurs.
ICC Test Condition, Active Mode, All Other Pins are Disconnected(1)
VDD
VDD
ICC
RST
GND
POL
(NC)
XTAL2
CLOCK SIGNAL
Notes:
18.8.4
VDD
XTAL1
GND
1. For active supply current measurements all ports are configured in quasi-bidirectional mode. Timers 0, 1 and 2 are configured to be free running in their default timer modes. The CPU executes a simple random number generator that accesses
RAM and SFR bus, and exercises the ALU and hardware multiplier.
ICC Test Condition, Idle Mode, All Other Pins are Disconnected
VDD
VDD
ICC
RST
GND
POL
(NC)
XTAL2
CLOCK SIGNAL
18.8.5
VDD
XTAL1
GND
Clock Signal Waveform for ICC Tests in Active and Idle Modes, tCLCH = tCHCL = 5 ns
VCC - 0.5V
0.45V
0.7 VCC
0.2 VCC - 0.1V
tCHCL
tCHCX
tCLCH
tCHCX
tCLCL
105
3709D–MICRO–12/11
18.8.6
ICC Test Condition, Power-down Mode, All Other Pins are Disconnected, VDD = 2V to 5.5V
VDD
VDD
ICC
RST
GND
POL
(NC)
XTAL2
VDD
XTAL1
GND
106
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
19. Ordering Information
19.1
Green Package Option (Pb/Halide-free)
Speed
(MHz)
20
20
Power
Supply
2.4V to 5.5V
2.4V to 5.5V
Code Memory
Ordering Code
Package
Operation Range
4KB
AT89LP51-20AU
AT89LP51-20PU
AT89LP51-20JU
AT89LP51-20MU
44A
40P6
44J
44M1
Industrial
(-40° C to 85° C)
8KB
AT89LP52-20AU
AT89LP52-20PU
AT89LP52-20JU
AT89LP52-20MU
44A
40P6
44J
44M1
Industrial
(-40° C to 85° C)
Package Types
44A
44-lead, Thin Plastic Quad Flat Package (TQFP)
40P6
40-lead, 0.600” Wide, Plastic Dual Inline Package (PDIP)
44J
44-lead, Plastic J-leaded Chip Carrier (PLCC)
44M1
44-pad, 7 x 7 x 1.0 mm Body, Plastic Very Thin Quad Flat No Lead Package (VQFN/MLF)
107
3709D–MICRO–12/11
20. Packaging Information
20.1
44A – TQFP
D1
D
e
E
E1
b
BOTTOM VIEW
TOP VIEW
C
COMMON DIMENSIONS
(Unit of Measure = mm)
0°~7°
A1
L
SIDE VIEW
A2
A
SYMBOL
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
11.75
12.00
12.25
D1
9.90
10.00
10.10
E
11.75
12.00
12.25
E1
9.90
10.00
10.10
B
0.30
–
0.45
C
0.09
–
0.20
L
0.45
–
0.75
e
Notes:
NOTE
Note 2
Note 2
0.80 TYP
1. This package conforms to JEDEC reference MS-026, Variation ACB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10 mm maximum.
09/23/11
TITLE
44A, 44-lead 10.0 x 10.0x1.0 mm Body, 0.80 mm
Package Drawing Contact:
[email protected] Lead Pitch, Thin Profile Plastic Quad Flat
GPC
DRAWING NO.
AIX
44A
REV.
C
Package (TQFP)
108
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
20.2
40P6 – PDIP
40
21
E1
1
20
D
e
A2 A
BASE
PLANE
-CSEATING
PLANE
A1
L
b2
.015
b j
0.10 m C
E
GAGE
PLANE
See
Lead Detail
Z Z
COMMON DIMENSIONS
(UNIT OF MEASURE=MM)
C
L
eC
Lead Detail
eA
eB
Notes:
1. This package conforms to JEDEC reference MS-011,
Variation AC.
2. Dimensions D and E1 do not include mold Flash or
Protrusion. Mold Flash or Protrusion shall not exceed
0.25 mm (0.010").
c
Symbol
A
A1
A2
Min.
0.39
3.18
Nom.
-
Max.
6.35
4.95
b
b2
c
D
E
0.356
0.77
0.204
50.3
15.24
-
0.558
1.77
0.381
53.2
15.87
E1
12.32
-
14.73
L
e
eA
eB
2.93
5.08
-
2.54 BSC
15.24 BSC
-
17.78
eC
0.000
-
1.524
Note
Note 2
Note 2
11/28/11
TITLE
40P6, 40-lead, 0.600”/15.24 mm Wide Plastic Dual
Package Drawing Contact:
[email protected] Inline Package (PDIP)
GPC
DRAWING NO.
REV.
PBL
40P6
C
109
3709D–MICRO–12/11
20.3
44J – PLCC
1.14(0.045) X 45˚
PIN NO. 1
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
IDENTIFIER
E1
D2/E2
B1
E
B
e
A2
D1
A1
D
A
0.51(0.020)MAX
45˚ MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-018, Variation AC.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
SYMBOL
MIN
NOM
MAX
A
4.191
–
4.572
A1
2.286
–
3.048
A2
0.508
–
–
D
17.399
–
17.653
D1
16.510
–
16.662
E
17.399
–
17.653
E1
16.510
–
16.662
D2/E2
14.986
–
16.002
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
R
110
2325 Orchard Parkway
San Jose, CA 95131
TITLE
44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC)
DRAWING NO.
REV.
44J
B
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
20.4
44M1 – VQFN/MLF
D
Marked Pin# 1 ID
E
SEATING PLANE
A1
TOP VIEW
A3
A
K
L
Pin #1 Corner
D2
1
2
3
Option A
SIDE VIEW
Pin #1
Triangle
E2
Option B
K
Option C
b
e
Pin #1
Chamfer
(C 0.30)
Pin #1
Notch
(0.20 R)
BOTTOM VIEW
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN
NOM
MAX
A
0.80
0.90
1.00
A1
–
0.02
0.05
A3
0.20 REF
b
0.18
0.23
0.30
D
6.90
7.00
7.10
D2
5.00
5.20
5.40
E
6.90
7.00
7.10
E2
5.00
5.20
5.40
e
Note: JEDEC Standard MO-220, Fig. 1 (SAW Singulation) VKKD-3.
NOTE
0.50 BSC
L
0.59
0.64
0.69
K
0.20
0.26
0.41
9/26/08
Package Drawing Contact:
[email protected]
TITLE
44M1, 44-pad, 7 x 7 x 1.0 mm Body, Lead
Pitch 0.50 mm, 5.20 mm Exposed Pad, Thermally
Enhanced Plastic Very Thin Quad Flat No
Lead Package (VQFN)
GPC
ZWS
DRAWING NO.
REV.
44M1
H
111
3709D–MICRO–12/11
21. Revision History
Revision No.
History
Revision A – September 2010
•
Initial Release
Revision B – December 2010
•
•
•
Added AT89LP51 device
Updated Device IDs
Lowered Minimum Operating Voltage to 2.4V
Revision C – May 2011
•
•
Added System Configuration (Section 2.2 on page 7)
Added Code size to Ordering table
•
•
Removed Preliminary Status
Updated AC/DC characteristics (Section 18.2 on page 92 and
Section 18.6 on page 102)
Added typical I/O characteristics (Section 18.3.3 on page 97,
Section 18.3.4 on page 98 and Section 18.3.5 on page 99)
Added note on active power measurement (page 105)
Revision D – December 2011
•
•
112
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Table of Contents
Features ..................................................................................................... 1
1
Pin Configurations ................................................................................... 2
1.1
40-lead PDIP .....................................................................................................2
1.2
44-lead TQFP ....................................................................................................2
.................................................................................................................... 3
2
3
1.3
44-lead PLCC ....................................................................................................3
1.4
44-pad VQFN/QFN/MLF ....................................................................................3
1.5
Pin Description ..................................................................................................4
Overview ................................................................................................... 6
2.1
Block Diagram ...................................................................................................7
2.2
System Configuration ........................................................................................7
2.3
Comparison to AT89S51/52 ..............................................................................8
Memory Organization ............................................................................ 11
3.1
Program Memory .............................................................................................11
3.2
Internal Data Memory ......................................................................................14
3.3
External Data Memory .....................................................................................14
3.4
In-Application Programming (IAP) ...................................................................23
4
Special Function Registers ................................................................... 24
5
Enhanced CPU ....................................................................................... 25
6
7
5.1
Fast Mode ........................................................................................................25
5.2
Compatibility Mode ..........................................................................................26
5.3
Enhanced Dual Data Pointers .........................................................................26
System Clock ......................................................................................... 29
6.1
Crystal Oscillator .............................................................................................29
6.2
External Clock Source .....................................................................................30
6.3
Internal RC Oscillator ......................................................................................30
6.4
System Clock Divider ......................................................................................31
Reset ....................................................................................................... 32
7.1
Power-on Reset ...............................................................................................32
7.2
Brown-out Reset ..............................................................................................33
7.3
External Reset .................................................................................................33
7.4
Watchdog Reset ..............................................................................................34
i
3709D–MICRO–12/11
Table of Contents (Continued)
7.5
8
9
Software Reset ................................................................................................34
Power Saving Modes ............................................................................. 34
8.1
Idle Mode .........................................................................................................34
8.2
Power-down Mode ...........................................................................................35
8.3
Reducing Power Consumption ........................................................................37
Interrupts ................................................................................................ 37
9.1
Interrupt Response Time .................................................................................38
10 I/O Ports .................................................................................................. 41
10.1
Port Configuration ............................................................................................41
10.2
Port Read-Modify-Write ...................................................................................44
10.3
Port Alternate Functions ..................................................................................45
11 Timer 0 and Timer 1 ............................................................................... 46
11.1
Mode 0 – 13-bit Timer/Counter ........................................................................47
11.2
Mode 1 – 16-bit Timer/Counter ........................................................................47
11.3
Mode 2 – 8-bit Auto-Reload Timer/Counter .....................................................48
11.4
Mode 3 – 8-bit Split Timer ...............................................................................48
11.5
Clock Output (Pin Toggle Mode) .....................................................................49
12 Timer 2 .................................................................................................... 51
12.1
Timer 2 Registers ............................................................................................52
12.2
Capture Mode ..................................................................................................53
12.3
Auto-Reload Mode ...........................................................................................53
12.4
Baud Rate Generator ......................................................................................55
12.5
Frequency Generator (Programmable Clock Out) ...........................................56
13 External Interrupts ................................................................................. 57
14 Serial Interface (UART) .......................................................................... 57
ii
14.1
Multiprocessor Communications .....................................................................59
14.2
Baud Rates ......................................................................................................59
14.3
Framing Error Detection ..................................................................................61
14.4
Automatic Address Recognition ......................................................................61
14.5
More About Mode 0 .........................................................................................63
14.6
More About Mode 1 .........................................................................................68
14.7
More About Modes 2 and 3 .............................................................................70
AT89LP51/52
3709D–MICRO–12/11
AT89LP51/52
Table of Contents (Continued)
15 Programmable Watchdog Timer ........................................................... 73
15.1
Software Reset ................................................................................................73
16 Instruction Set Summary ...................................................................... 75
17 Programming the Flash Memory .......................................................... 79
17.1
Physical Interface ............................................................................................79
17.2
Memory Organization ......................................................................................81
17.3
Command Format ............................................................................................82
17.4
Status Register ................................................................................................85
17.5
DATA Polling ...................................................................................................85
17.6
Flash Security ..................................................................................................85
17.7
User Configuration Fuses ................................................................................86
17.8
User Signature .................................................................................................87
17.9
Programming Interface Timing ........................................................................87
18 Electrical Characteristics ...................................................................... 92
18.1
Absolute Maximum Ratings* ...........................................................................92
18.2
DC Characteristics ...........................................................................................92
18.3
Typical Characteristics ....................................................................................93
18.4
Clock Characteristics .....................................................................................100
18.5
Reset Characteristics ....................................................................................101
18.6
External Memory Characteristics ...................................................................102
18.7
Serial Port Timing: Shift Register Mode ........................................................104
18.8
Test Conditions ..............................................................................................104
19 Ordering Information ........................................................................... 107
19.1
Green Package Option (Pb/Halide-free) ........................................................107
20 Packaging Information ........................................................................ 108
20.1
44A – TQFP ...................................................................................................108
20.2
40P6 – PDIP ..................................................................................................109
20.3
44J – PLCC ...................................................................................................110
20.4
44M1 – VQFN/MLF .......................................................................................111
21 Revision History ................................................................................... 112
Table of Contents....................................................................................... i
iii
3709D–MICRO–12/11
iv
AT89LP51/52
3709D–MICRO–12/11
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: (+1) (408) 441-0311
Fax: (+1) (408) 487-2600
www.atmel.com
[email protected]
Atmel Asia Limited
Unit 1-5 & 16, 19/F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
HONG KONG
Tel: (+852) 2245-6100
Fax: (+852) 2722-1369
Atmel Munich GmbH
Business Campus
Parkring 4
D-85748 Garching b. Munich
GERMANY
Tel: (+49) 89-31970-0
Fax: (+49) 89-3194621
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
JAPAN
Tel: (+81) (3) 3523-3551
Fax: (+81) (3) 3523-7581
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2011 Atmel Corporation. All rights reserved. Atmel ®, Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
3709D–MICRO–12/11