Data Sheet

M5500 Series
Crystal Oscillators HCMOS 5V Thru-Hole
High Reliability 1 Hz to 125 MHz
Extended Temperature Hi-Rel Product Specification
Features
ƒ
ƒ
ƒ
ƒ
ƒ
XO
Description
Hermetically sealed half size or full size DIL package
Crystal angle controlled to +/-1 minute for excellent
temperature stability
168 hour Class B burn-in and extensive
environmental testing for best performance in rugged
field environments
Start-up time less than 10 ms, typical
Serialized test data available
Typical Applications
Thru-hole PCB projects requiring high reliability
HCMOS clock waveforms
Full Size
Half Size
Model
M5500, M5516
M5515
Package
M-2
M-2
Model
M5622
M5623
M
M
H5622
H5623
Package
H
H
These high reliability oscillators provide HCMOS
clock waveforms for applications subjected to the
most stringent environmental conditions. They are
through-hole mechanically robust oscillators. The
“M-2” package has 14 pins which provides greater
holdability onto the pc board. Each oscillator is
burned-in at 125°C for 168 hours, temperature
cycled and centrifuged and fully tested in
accordance with Table 1. Reliability tests are
performed per Table 2. The calculated MTBF is
1.4 X 106 hours at 125°C.
Operating
Temperature
Frequency Stability
-55 to +125°C
0 to 70°C
+/-75 ppm
+/-50 ppm
-55 to +85°C
-55 to +125°C
+/-50 ppm
+/-75 ppm
Valpey Fisher Corporation • 75 South Street, Hopkinton, MA 01748 • Tel. 1-800-XTALREP, 508-435-6831 • FAX 508 4355289
1
Rev 1.0 11/04
M5500 Series
Crystal Oscillators HCMOS 5V Thru-Hole
High Reliability 1 Hz to 125 MHz
Pin
M5500
M5515, M5516
Frequency Range
M5500, M5515, M5516, M5622, M5623- 1 Hz to 125 MHz
H5622, H5623-1KHz to 125 MHz
Frequency Stability
Includes calibration at 25°C, operating temperature, change of input voltage,
change of load, shock and vibration.
MIN
TYP
MAX
UNITS
Input Voltage,
4.5
5.0
5.5
volts
M5622,
M5623
1.
Case
N.C
Case & Electrical
Ground
2.
N.C.
N.C.
3.
N.C.
N.C
Pins 2 thru 6 are
not present
4.
N.C.
N.C.
5.
N.C.
N.C.
6.
N.C.
N.C.
Input Current
Frequency at 1 KHz or above
Frequency below 1 KHz
Frequency Accuracy
Waveform Symmetry
Measured at 1.5V
Rise and Fall Times
Below 10 MHz
0.8 to 2.4volts
10 MHz and above,
0.8 to 2.4 volts
“Zero” Level,
Sinking 16 mA
“One” Level
Sourcing 400 microAmps
Sourcing to 10 TTL loads
Frequency Change
From +5.5 to +5.0V
From +4.5 to +5.0V
Aging
First year
After first year
7.
8.
9.
Electrical
Ground
Output
N.C.
Case & Electrical
Ground
Output
N.C.
10.
N.C.
N.C.
11.
N.C.
N.C.
12.
13.
14.
N.C.
N.C.
+5V, VDD
N.C.
N.C.
+5V, VDD
ELECTRICAL SPECIFICATIONS
30
55
35
60
See Preceding Table
40/60
60/40
mA
mA
percent
5
15
ns
2
5
ns
0.5
volts
4.5
2.5
volts
volts
+/-5
+/-5
3
1
+/-10
+/-10
ppm
ppm
CONNECTIONS
Pin 1.
Pin 4.
Pin 5.
Pin 8.
Case & Electrical
Ground
Output
Pins 9 thru 13 are
not present
+5V, VDD
Half Size
Not Used
Ground and Case
Output
+5V, VDD
ppm
ppm/yr
ENVIRONMENTAL SPECIFICATIONS
Shock- MIL-STD 883, Method 2002, Test Condition B (1500 peak g, 0.5
ms duration, ½ sine wave, 5 shocks in 6 planes)
Vibration- MIL-STD 883, Method 2007, Test Condition A (20-2000 Hz
of .06” d.a. or 20 Gs, whichever is less)
Humidity- Resistant to 85° R.H. at 85°C
Valpey Fisher Corporation • 75 South Street, Hopkinton, MA 01748 • Tel. 1-800-XTALREP, 508-435-6831 • FAX 508 4355289
2
Rev 1.0 11/04
M5500 Series
Crystal Oscillators HCMOS 5V Thru-Hole
High Reliability 1 Hz to 125 MHz
MECHANICAL DESCRIPTION
Case- Stainless Steel
Marking- Valpey part number, date code, serial number and
description. Markings will withstand MIL-STD 202, Method
215.
Optional Marking- Customer part number if required
Leads- Kovar, nickel plated, gold flash
Shock- MIL-STD 883, Method 2002, Test Condition B
Vibration- MIL-STD 883, Method 2007, Test Condition A
TABLE 2- RELIABILITY TEST PROCEDURE AND CONDITIONS FOR
QUARTZ CRYSTAL OSCILLATORS
1.
Group A
Electrical Characteristics at -55°, (0° for ‘5515), 25° and 125° (70° for M5515 and 85°
for M5622)
Frequency @ 4.5, 5.0 and 5.5 volts (for 5 volts units)
Symmetry (Duty Cycle)
Input current
Zero/One levels
Rise/Fall times
Physical Dimensions
Length/width
Height
Package finish (Corrosion, discoloration, etc.)
Marking placement/legibility
II. Group B- Life Test
1000 hrs at 125°C with bias and load
III.
Group C- All units have passed Group A testing
A. Subgroup 1-8 pcs.
TABLE 1
Each unit undergoes the following:
1. Stabilization Bake
2. Temperature Cycling
3. Centrifuge
4. Burn-in
MIL-STD-883 Method 1008, Cond. B
MIL-STD-883 Method 1010, Cond B
MIL-STD-883 Method 2001, Cond. A
MIL-STD-1015 1015, Cond. B
(125°C for 168 hours with bias)
5. Fine Leak
MIL-STD-883 Method 1014, Cond. A1
6. Gross Leak
MIL-STD-883, Method 1014, Cond. C
7. Electrical Test at 25°C and temperature extremes, as follows:
A.
B.
C.
D.
E.
Frequency*
Current
Rise Time (FL)
Fall Time (FL)
Duty Cycle (NL)
F. Duty Cycle (FL)
G. Frequency at 5.5V
H. Frequency at 4.5V
I. “Zero” logic level
J. “One” logic level
M5623)
Within 50 ppm from 0 to +70°C (M5515)
Within 50 ppm from -55 to +85°C (M5622)
HOW TO ORDER
For Part Number, put package type before mode number, and
add frequency in MHz, for example:
M is full size DIL
H is half size DIL
5516 5516
is model type
Condition
Method 2002
COND.B
Description
End point measurement
Mechanical Shock
1500 g’s, 5ms
5 drops, 6 axis
MIL-STD-883
Method 2007
Vibration, var.
COND. A.
freq. 20 g’s,
.06” disp., 2020, 000-20 Hz
MIL-STD-883
Method 2003
Solderability
B. Subgroup 2-4 pcs (One-half of Subgroup 1)
MIL-STD-883
Method 1011
Thermal Shock
COND. B
Liq. To liq.
15 cycles
MIL-STD-202
Method 105
Altitude, 3.44
COND. B
inch Hg. 12 hrs
MIL-STD-883
Method 1004
Moisture resist.
With 5V applied
25-65°C, 90 to
100% RH, 10 cycles
MIL-STD-202
Method 210
Resistance to
COND.A
Solder Heat
Immersion @350°C
3.5 sec
C.Subgroups 3-4 pcs. (One half of Subgroup 1)
*Within 75 ppm from -55 to +125°C (M5500, M5516 and
M
Standard
MIL-STD-883
Standard
32M
MIL-STD-883
MIL-STD-883
32M Frequency
in MHz
MIL-STD-883
Frequency
Output Waveform
Frequency
Output waveform
Visual 95% coverage
Frequency
Output waveform
Frequency
Output waveform
Frequency
Output waveform
Frequency
Output waveform
Condition
Description
Storage Temp.
No. Oper
Method 1009
COND. A
24 hrs. @ -55°C
24 hrs. @ 125°C
Salt Atmosphere
24 hrs. @ 35°C
.5-3.0% Solution
Fine Leak
Frequency
Output waveform
Frequency
Output waveform
Visual
Qs <5 X10-8
Gross Leak
Visual in 125°C
Detector fluid
Method 1014
COND. B
Method 1014
COND. C
End point measurement
Valpey Fisher Corporation • 75 South Street, Hopkinton, MA 01748 • Tel. 1-800-XTALREP, 508-435-6831 • FAX 508 4355289
3
Rev 1.0 11/04