Tel : Fax : email : 0044 (0)118 979 1238 0044 (0)118 979 1283 [email protected] ACT1100 / ACT1700 Standard Clock Oscillators The ACT1100 is a full size through hole oscillator. The ACT1700 is a half size through hole oscillator. The popularity of these families still remains even after the advent of smaller surface mount devices. With wide frequency and operating temperature ranges, these series offer low cost & good reliability for ATM, Networking, Microprocessor and Consumer applications. An option with a supply voltage of 2.5V is available please contact our sales desk for details. For frequencies < 500KHz, >125MHz & ± 10ppm stability please refer to the ACT1100HS/1700HS data. Specification Parameter Frequency Range Frequency Stability Temp Operating Range Temp Storage Range Supply Voltage Symbol fo Δf/fo Topr Tstg VDD Supply Current Iop Duty Cycle TW/t Output Level ‘0’ VOL Output Level ‘1’ VOH Output Logic Output Load Rise & Fall Time Start-up Time Option on Pin 1 Aging tr/tf Specification Condition Please Specify Please Specify Please Specify 500KHz ~ 125.0MHz ±25ppm, ±50ppm and ±100ppm 0 ~ +70°, -10 ~ +70°C -40~85°C 3.3Vdc ±10% 5.0Vdc ±10% 15mA max 25mA max 25mA max 35mA max 40/60%, 45/55% TTL 40/60%, 45/55% HCMOS TTL 0.4V max, HCMOS .33V max TTL 0.4V max, HCMOS 0.5V max TTL 2.4V min, HCMOS 2.97V min VDD TTL 2.4V min, HCMOS 4.5V min VDD TTL / HCMOS TTL 10 Gates CMOS 15 pF TTL 10nSec max, 3nSec typical Measured between 0.4V ~ 2.4V (RL = 390Ω ; CL = 15pF) CMOS 10nSec max, 3nSec typical Measured between 10%~ 90% VDD (CL = 15pF) 4mSec max, Tri State or No Connection ±5ppm / year max Please Specify 0.5 - 27MHz 27 - 125MHz Measured at +1.4Volts Measured at 50% VDD VDD = 3.3V VDD = 5.0V VDD = 3.3V VDD = 5.0V Please Specify @25°C Plating Material on leads SnAgCu Soldering conditions please refer to page 3 ACT1100 ( 'V' SERIES ) ACT1700 ( 'CL' SERIES ) Please note that all parameters can not necessarily be specified in the same device Customer to specify : Frequency, Operating Temperature Range, Frequency Stability, Supply Voltage, Duty Cycle, Output Enable (Tristate) If required In line with our ongoing policy of product evolvement and improvement, the above specification may be subject to change without notice ISO9001:2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berkshire, RG41 2EY, UK http://www.actcrystals.com Issue 5 C1A Date 23/3/6 1 of 3 Tel : Fax : email : 0044 (0)118 979 1238 0044 (0)118 979 1283 [email protected] ACT1100 / ACT1700 Standard Clock Oscillators Reliability tests Test Leak Helium bomb: Pressure 200kpa Time 70 min pressure release 5 min measure within 30min Drop 750mm height. 3 drops. Onto wood. Shock Vibration Resistance to Soldering Heat Aging Measurement Requirements Test Method <4x10-9pa.m3/s Peak acceleration 981m/s2 Pulse duration 6ms Each of X, Y and Z axis. 3 shocks each axis 10 to 55Hz and return to 10Hzamplitude 1.5mm sweep time 1min. 2 hrs each of X, Y and Z axis. Total test time 6 hrs As per profile fig.1 below and/or soldering iron applied for 5s max tip temperature 350±10°C 85±3°C 30 days measurements after at least 1 hr at atmospheric conditions. High Temperature 105±3°C 16 hrs measurements after at least 1 hr at atmospheric conditions Storage Specification as per page 1 must be met. Low Temperature -55±3°C 2hrs measurements after at least 1 hr at atmospheric conditions Storage Thermal Cycling Damp Heat Constant Solderability 100cycles to the temperature profile fig 2 below. Measurements after at least 1 hr at atmospheric conditions Temperature 40±2°C RH 90~95% for 56 days. Measurements after at 1 hr at atmospheric conditions 255±5°C for 10±0.5s using Rosin resin methyl alcohol flux Solvent (1:4) dipped to a nominal depth of 0.5mm. In line with our ongoing policy of product evolvement and improvement, the above specification may be subject to change without notice ISO9001:2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berkshire, RG41 2EY, UK http://www.actcrystals.com Issue 5 C1A Date 23/3/6 2 of 3 Tel : Fax : email : 0044 (0)118 979 1238 0044 (0)118 979 1283 [email protected] ACT1100 / ACT1700 Standard Clock Oscillators Application circuits In line with our ongoing policy of product evolvement and improvement, the above specification may be subject to change without notice ISO9001:2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berkshire, RG41 2EY, UK http://www.actcrystals.com Issue 5 C1A Date 23/3/6 3 of 3