CRYSTAL OSCILLATORS 10KH PECL 5V FULL SIZE D.I.L M package HALF SIZE D.I.L H package M1700, M1744, M1748, M1936, M1945, M2700, M2744, M2748 H1700, H1744, H1748, H1936, H1945, H2700, H2744, H2748 M1736, M1745, M1900, M1944, M1948, M2736, M2745, H1736, H1745, H1900, H1944, H1948, H2736, H2745, Thru-Hole / Gull Wing Commercial: 0º to 70ºC 10 MHZ to 210 MHZ The MF PECL oscillators are available in a variety of common configurations. Models are full size or half size, in 10 KH logic, with and without complementary outputs. Frequency tolerances from 100 ppm to 20 ppm include all effects of voltage, load and aging. Description MF Electronics’ high speed clock oscillators for digital and communications applications are based on 5V PECL logic and are available in full size (M) and half size (H) thru-hole packages. Designs in 10KH logic develop 10 MHz to 210 MHz output, and are available with 45/55 symmetry. They can be optionally provided with dual complementary output. Frequency stability extends from the high end at ±20 ppm to ±100 ppm. For superior performance, see our model 2900s using ECLPS logic. FEATURES • DIL – full size or half size • Single or dual complementary outputs • H1900 and M1900 have Enable/Disable, reducing noise of unwanted frequency • Start up time less than 5 ms • Stability options from .01% (100 ppm) to .002% (20 ppm) • Guaranteed start-up with ramping DC Supply • Terminating resistor may be internal – consult factory PECL OSCILLATORS Single Output Complementary Output Enable/Disable Output Frequency Stability 1700 1736* 1744 1745 1748 2700 2736* 2744 2745 2748 1900 1936* 1944 1945 1948 ±100 ppm ±100 ppm ±25 ppm ±50 ppm ±20 ppm * Guaranteed Superior Symmetry 45/55 DOT DENOTES PIN 1 DOT DENOTES PIN 1 .018 – .001 DOT DENOTES PIN 1 .800 – .005 .060 TYP .300 – .005 DOT DENOTES PIN 1 .52 MAX SQUARE .200 MAX .215 MAX .2 MAX .008/025 .15 MIN .160 .2 MAX .018 .400 .600 – .005 Pin 1 .150 Pin 8 .250 MAX Pin 7 4 5 .520 – .005 .300 +.004 .300 –. 005 5 Pin 14 Pin 8 GLASS INSULATORS (4) “M” Package .300 +.004 4 .300 8 .070 .018 .600 – .005 .500 – .005 .200 MAX .018 – .001 Pin 1 1 .300 –. 005 Pin 14 .52 MAX SQUARE .200 MAX .270 MAX .300 .100 – .005 Pin 7 .800 – .005 GLASS INSULATORS (4) on .48 x .18 ctrs. “H” Package “M” Package with Gull Wing 1 8 Glass Insulators (4) “H” Package with Gull Wing ELECTRONICS 10 Commerce Dr • New Rochelle NY 10801 International Sales: +1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:[email protected] 1 of 3 CRYSTAL OSCILLATORS 10KH PECL 5V Thru-Hole /Gull Wing Commercial: 0º to 70º 10 MHz to 210 MHz FULL SIZE D.I.L M package HALF SIZE D.I.L H package M1700, M1744, M1748, M1936, M1945, M2700, M2744, M2748 H1700, H1744, H1748, H1936, H1945, H2700, H2744, H2748 M1736, M1745, M1900, M1944, M1948, M2736, M2745, H1736, H1745, H1900, H1944, H1948, H2736, H2745, +5V TERMINATIONS All ECL oscillators must be terminated. If required, internal terminating resistors of any specified value may be factory-supplied COMPLEMENTARY OUTPUT 1 ON (1) ’2700 ENABLE/DISABLE The M1900 and H1900 have Enable-Disable feature, which allows several oscillators to be wire-OR'd, so that one frequency of several may be selected. If Pin1. is “0”, the output is normal, However, when Pin1. is “1”, the oscillator shuts-down, and the output goes to logic “0”'. The logic “0” may be wire-OR'd. 7 ’1700 & ’2700 (4) 14 (8) 8 CASE (5) OUTPUT Half size connections shown in ( ) Fig. 1 AUTOMATED TESTING (ATE) Automated testing can effectively be performed using the M1900, since this model may be turned-off and “0”'d, allowing an ECL test frequency to be inserted on the output node. +5V ENABLE: FLOAT OR “0” DISABLE APPLY “1” 1 (1) 14 (8) M1900 7 ELECTRICAL SPECIFICATIONS Frequency Range 10 MHz to 210 MHz Frequency Stability Includes calibration at 25°C, operating temperature, change of input voltage, change of load, shock and vibration. MIN 4.75 Input Voltage Input Current Output Levels “0” Level 25°C 75° “1” Level 25°C 75° TYP 5.0 MAX 5.25 UNITS volts 45 60 mA 8 CASE (5) OUTPUT (“0”, WHEN DISABLED) Half size connections shown in ( ) Fig. 2 Note: Outputs must be properly terminated ENVIRONMENTAL SPECIFICATIONS Temperature Operating Storage 0º to 70°C -55º to +125°C (VC–1.95) (VC–1.95) (VC–1.63) (VC–1.60) volts volts (VC–0.98) (VC–0.92) (VC–0.81) (VC–0.735) volts volts Humidity – Resistant to 85° R.H. at 85°C 0.85 mA MECHANICAL SPECIFICATIONS Shock – 1000 Gs, 0.35 ms, 1/2 sine wave, 3 shocks in each plane Vibration – 10-2000 Hz of .06" d.a. or 20 Gs, whichever is less Drive Required for 1900 (at ECL levels) Rise and Fall Times (20 to 80%) Symmetry All units, except ‘36 Models All ‘36 Models Aging First year After first year (4) Leak – MIL STD 883, Method 1014, condition A1 Pins – Kovar, 7 microinch gold over nickel 1.0 2.0 ns 45/55 48/52 40/60 45/55 percent percent Header – Steel, 7 microinch gold over nickel ppm ppm/yr Marking – Epoxy ink or laser engraved Bend Test – Will withstand two bends of 90° from reference 3 1 Case – Stainless steel, type 304 Resistance to Solvents – MIL STD 202, Method 215 ELECTRONICS 10 Commerce Dr • New Rochelle NY 10801 International Sales: +1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:[email protected] 2 of 3 CRYSTAL OSCILLATORS 10KH PECL 5V Thru-Hole /Gull Wing Commercial: 0º to 70º 10 MHz to 210 MHz FULL SIZE D.I.L M package HALF SIZE D.I.L H package M1700, M1744, M1748, M1936, M1945, M2700, M2744, M2748 H1700, H1744, H1748, H1936, H1945, H2700, H2744, H2748 M1736, M1745, M1900, M1944, M1948, M2736, M2745, H1736, H1745, H1900, H1944, H1948, H2736, H2745, CONNECTIONS PINS Full Half Size Size H1700, H2700, H1900 M1700, M2700, M1900 Models Not used in Single Output or Used for Complementary Output (Same termination as Pin 8.) Used for H1900 and M1900. Float or “0” for normal operation, “1” for “0” Output 1. 1. 7. 4. Electrical Ground and Case 5. Output requires termination of 270 ohms to Pin 7 (4) or 50 ohms to +3V 8. 14. 8. +5V, VDD CASE Tied to Pin 7. “0” FOR NORMAL OPERATION “1” FOR DISABLE (“0” OUTPUT) 50Ω +5V Power Supply 1 (1) IMF 14 (8) COAX 1900’s 7 GND Y-OUTPUT 350 MHz SCOPE +3V MA COUNTER 8 (5) (4) Half Size connections shown in ( ) To connect output to scope use Tektronix Part #131-0258-00 (receptacle) To adapt Fet probe to receptacle use Tektronix Part #103-0164-00 TEST CIRCUIT FOR 1900’s COMPLEMENTARY OUTPUT FOR 2700’s 50Ω +5V Power Supply MA 1 (1) IMF GND 7 (4) Half Size connections shown in ( ) To adapt Fet probe to receptacle use Tektronix Part #103-0164-00 1700’s & 2700’s Y-OUTPUT 350 MHz SCOPE +3V 14 (8) COAX 8 (5) COUNTER To connect output to scope use Tektronix Part #131-0258-00 (receptacle) Fig. 3 M1700-80M TEST CIRCUIT FOR 2700’s HAVE ADDITIONAL OUTPUT ON PIN 1. HOW TO ORDER For Part Number, put package type before model number, and add frequency in MHz, for example: M 1700 - 77.76M “M” is full size DIL “H” is half size DIL SS# Rev. M1700 A “1700” is model type “77.76 M” frequency in MHz Leave blank for straight leads Add “G” for gullwing ELECTRONICS Unless customer-specific terms and conditions are signed by an officer of MF Electronics, the sale of this and all MF Electronics products are subject to terms and conditions set forth at www.mfelectronics.com/terms 10 Commerce Dr • New Rochelle NY 10801 International Sales: +1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:[email protected] 3 of 3